Arsenie Treatment
  Technologies for
Soil, Waste, and Water

-------

-------
                                      Solid Waste
                                      and Emergency Response
                                      (5102G)
EPA-542-R-02-004
September 2002
www.epa.gov/tio
clu-in.org/arsenic
             Arsenic Treatment Technologies for Soil, Waste, and Water
                               Internet Address (URL) • http://www.epa.gov
Recycled/Recyclable • Printed with Vegetable Oil Based,Inks on Process Chlorine Free Recycled Paper (minimum 50% Postconsumer)

-------

-------
                                 TABLE OF CONTENTS
Section                                                                           Page
LIST OF ACRONYMS AND ABBREVIATIONS	iv
FOREWORD	 v
NOTICE AND DISCLAIMER	;...'	:	vi
ACKNOWLEDGMENTS ....:	;.	vi

PARTI       OVERVIEW AND FINDINGS
1.0 .    EXECUTIVE SUMMARY	•'	1-1
2.0     INTRODUCTION	'.	2-1
       2.1    Who Needs to Know about Arsenic Treatment Technologies?	2-1
       2.2    Background	2-1
       2.3    How Often Does Arsenic Occur in Drinking Water? 	2-2
       2.4    How Often Does Arsenic Occur* at Hazardous Waste Sites?	2-2
       2.5    What Are the Structure and Contents of the Report?	2-4
       2.6    What Technologies and Media Are Addressed in This Report? 	2-5
       2.7    How Is Technology Scale Defined? 		2-5
       2.8    How Are Treatment Trains Addressed?	2-5
       2.9    What Are the Sources of Information for This Report?	2-5
       2.10   What Other Types of Literature Were Searched and Referenced for This Report?	2-6
       2.11   References	•.	2-6
3.0     COMPARISON OF ARSENIC TREATMENT TECHNOLOGIES	3-1
       3.1    What Technologies Are Used to Treat Arsenic?	3-1
       3.2    What Technologies Are Used Most Often to Treat Arsenic?  	3-1
       3.3 '   What Factors Affect Technology Selection for Drinking Water Treatment? 	3-3
       3.4    How Effective Are Arsenic Treatment Technologies? 	3-4
       3.5    What Are Special Considerations for Retrofitting Existing Water Treatment Systems?	3-4
       3.6    How Do I Screen Arsenic Treatment Technologies?	3-5
       3.7    What Does Arsenic Treatment Cost?	3-6
       3.8    References	3-7
PART II      ARSENIC TREATMENT TECHNOLOGY SUMMARIES
PART IIA     ARSENIC TREATMENT TECHNOLOGIES APPLICABLE TO SOIL AND WASTE
4.0   .  SOLIDIFICATION AND STABILIZATION TREATMENT FOR ARSENIC  	4-1
5.0     VITRIFICATION FOR ARSENIC	5-1
6.0     SOIL WASHING/ACID EXTRACTION; FOR ARSENIC		6-1
7.0     PYROMETALLURGICAL RECOVERY FOR ARSENIC 	7-1
8.0     IN SITU SOIL FLUSHING FOR ARSENIC 	8-1
PART IIB     ARSENIC TREATMENT TECHNOLOGIES APPLICABLE TO WATER
9.0     PRECIPITATION/COPRECIPITATION FOR ARSENIC	9-1
10.0    MEMBRANE FILTRATION FOR ARSENIC	10-1
11.0    ADSORPTION TREATMENT FOR ARSENIC	11-1

-------
12.0    ION EXCHANGE FOR ARSENIC	12-1

13.0    PERMEABLE REACTIVE BARRIERS FOR ARSENIC  	13-1

PART IIC     ARSENIC TREATMENT TECHNOLOGIES APPLICABLE TO SOIL, WASTE, AND
              WATER

14.0    ELECTROKINETIC TREATMENT OF ARSENIC	14-1

15.0    PHYTOREMEDIATION TREATMENT OF ARSENIC	15-1

16.0    BIOLOGICAL TREATMENT FOR ARSENIC	16-1

APPENDICES

APPENDIX A - LITERATURE SEARCH RESULTS (available only in on-line version)  	 A-l

APPENDIX B - SUPERFUND SITES WITH ARSENIC AS A CONSTITUENT OF CONCERN	 B-l


                                       LIST OF TABLES

Table                                                                                    Page

1.1     Arsenic Treatment Technology Descriptions	1-3
1,2     Summary of Key Data and Findings 	1-4
2.1     Number of Superfund Sites with Arsenic as a Contaminant of Concern by Media	2-2
2.2     Number of Superfund Sites with Arsenic as a Contaminant of Concern by Site Type  	2-4
3.1     Applicability of Arsenic Treatment Technologies	3-9
3.2     Arsenic Treatment Technologies Screening Matrix	3-10
3.3     Available Arsenic Treatment Cost Data	3-15
3.4     Summary of Cost Data for Treatment of Arsenic in Drinking Water  	3-17
4.1     Solidification/Stabilization Treatment Performance Data for Arsenic	4-6
4.2     Long-Term Solidification/Stabilization Treatment Performance Data for Arsenic	4-12
5.1     Vitrification Treatment Performance Data for Arsenic 	5-5
6.1     Soil Washing/Acid Extraction Treatment Performance Data for Arsenic 	6-4
7.1     Pyrometallurgical Treatment Performance Data for Arsenic	7-4
8.1     In Situ Soil Flushing Treatment Performance Data for Arsenic	8-4
9.1     Precipitation/Coprecipitation Treatment Performance Data for Arsenic	9-7
10.1    Membrane Filtration Treatment Performance Data for Arsenic	10-5
11.1    Adsorption Treatment Performance Data for Arsenic	11-6
12.1    Ion Exchange Treatment Performance Data for Arsenic	12-5
13.1    Permeable Reactive Barrier Treatment Performance Data for Arsenic	13-6
14.1    Electrokinetics Treatment Performance Data for Arsenic	14-5
15.1    Phytoremediation Treatment Performance Data for Arsenic	15-5
16.1    Biological Treatment Performance Data for Arsenic	16-4


                                       LIST OF FIGURES

Figure                                                                                   Page

2.1     Top Twelve Contaminants of Concern at Superfund Sites  	2-3
2.2     Number of Applications of Arsenic Treatment Technologies at Superfund Sites	2-4
3.1     Number of Identified Applications of Arsenic Treatment Technologies for Soil and Waste	3-2
3.2     Number of Identified Applications of Arsenic Treatment Technologies for Water	3-2

-------
                                     LIST OF FIGURES (continued)
Figure

3.3
4.1

4.2
5.1
6.1
7.1
8.1
9.1
10.1
11.1
12.1
13.1
14.1
15.1
16.1
Page
3-3
Number of Identified Applications of Arsenic Treatment Technologies for Soil, Waste, and Water
Binders and Reagents Used for Solidification/Stabilization of Arsenic for 21 Identified Superfund
Remedial Action Projects	'	4-1
Scale of Identified Solidification/Stabilization Projects for Arsenic Treatment	4-2
Scale of Identified Vitrification Projects for Arsenic Treatment	5-2
Scale of Identified Soil Washing/Acid Extraction Projects for Arsenic Treatment	6-1
Scale of Identified Pyrometallurgical Recovery Projects for Arsenic Treatment	:	7-1
Scale of Identified In Situ Soil Flushing Projects for Arsenic Treatment  	8-1
Scale of Identified Precipitaition/Coprecipitation Projects for Arsenic Treatment  	9-2
Scale of Identified Membrane Filtration Projects for Arsenic Treatment  	10-2
Scale of Identified Adsorption Projects for Arsenic Treatment	11-2
Scale of Identified Ion Exchange Projects for Arsenic Treatment	12-2
Scale of Identified Permeable Reactive bkrrier Projects for Arsenic Treatment 	13-3
Scale of Identified Electrokinetics Projects for Arsenic Treatment	14-3
Scale of Identified Phytoremediation Projects for Arsenic Treatment	15-2
Scale of Identified Biological Treatment Projects for Arsenic Treatment	16-2
                                                   in

-------
                           LIST OF ACRONYMS AND ABBREVIATIONS
AA         Activated alumina
AC         Activated carbon
ASR        Annual Status Report
As(III)      Trivalent arsenic, common inorganic form
            in water is arsenite, H3AsO3
As(V)       Pentavalent arsenic, common inorganic
            form in water is arsenate, H2AsO4"
BOAT      best demonstrated available technology
BTEX       Benzene, toluene, ethylbenzene, and
            xylene
CCA        Chromated copper arsenate
CERCLA    Comprehensive Environmental Response,
            Compensation, and Liability Act
CERCLIS 3  CERCLA Information System
CLU-IN     EPA's CLeanUp INformation system
CWS        Community Water System
cy          Cubic yard
DDT        Dichloro-diphenyl-trichloroethane
DI          Deionized
DOC        Dissolved organic carbon
DoD        Department of Defense
DOE        Department of Energy
EDTA       Ethylenediaminetetraacetic acid
EPA        U.S. Environmental Protection Agency
EPT        Extraction Procedure Toxicity Test
FRTR       Federal Remediation Technologies
            Roundtable
ft           feet
GJO        DOE's Grand Junction Office
gpd         gallons per day
gpm        gallons per minute
HTMR      High temperature metals recovery
MCL        Maximum Contaminant Level
            (enforceable drinking water standard)
MF         Microfiltration
MHO       Metallurgie-Hobqken-Overpelt
mgd      •  million gallons per day
mg/kg       milligrams per kilogram
mg/L       milligrams per Liter
NF         Nanofiltration
NPL        National Priorities List
OCLC       Online Computer Library Center
ORD       EPA Office of Research and Development
OU         Operable Unit
PAH        Polycyclic aromatic hydrocarbons
PCB        Polychlorinated biphenyls
POTW      Publicly owned treatment works
PRB        Permeable reactive barrier
RCRA      Resource Conservation and Recovery Act
Redox       Reduction/oxidation
RO         Reverse osmosis
ROD       Record of Decision
SDWA      Safe Drinking Water Act
SMZ        surfactant modified zeolite
SNAP       Superfund NPL Assessment Program
S/S         Solidification/Stabilization
SVOC       Semivolatile organic compounds
TCLP       Toxicity Characteristic Leaching
            Procedure
TNT        2,3,6-trinitrotoluene
TWA       Total Waste Analysis
UF         Ultrafiltration
VOC        Volatile organic compounds
WET       Waste Extraction Test
ZVI        Zero valent iron
                                                 IV

-------
                                               FOREWORD

The purpose of this report is to provide a synopsis of the availability, performance, and cost of 13 arsenic treatment
technologies for soil, water, and waste. Its intended audience includes hazardous waste site managers; generators
and treaters of arsenic-contaminated waste and wastewater; owners and operators of drinking water treatment plants;
regulators; and the interested public.           ,'

There is a growing need for cost-effective arsenic treatment. The presence of arsenic in the environment can pose a
risk to human health. Historical and current indu$trial use of arsenic has resulted in soil and groundwater
contamination that may require remediation.  Sorrie industrial wastes and wastewaters currently being produced
require treatment to remove or immobilize arsenic. In addition, arsenic must be removed from some sources of
drinking water before they can be used.         ,

Recently the EPA reduced the maximum contaminant level (MCL) for arsenic in drinking water from 0.050 mg/L to
0.010 mg/L, effective in 2006. Current and futur$ drinking water and groundwater treatment systems will require
better-performing technologies to achieve this lower level.  EPA recently prepared an issue paper, Proven
Alternatives for Aboveground Treatment of Arsenic in Groundwater, that describes four technologies
(precipitation/coprecipitation, adsorption, ion exchange, and membrane filtration) for removing arsenic from water.
The paper also discusses special considerations for retrofitting systems to meet the lower arsenic drinking water
standard.  This information is incorporated in this report, as well as details on emerging approaches, such as
phytoremediation and electrokinetics, for addressing arsenic in groundwater.

This report is intended to be used as a screening tool for arsenic treatment technologies. It provides descriptions of
the theory, design, and operation of the technologies; information on commercial availability and use; performance
and cost data, where available; and a discussion of factors affecting effectiveness and cost. As a technology
overview document, the information can serve asia starting point for identifying  options for arsenic treatment. The
feasibility of particular technologies will depend heavily on site-specific factors, and final treatment and remedy
decisions will require further analysis, expertise, and possibly treatability studies.

-------
                                     NOTICE AND DISCLAIMER

Preparation of this report has been funded by the U.S. Environmental Protection Agency (EPA) Technology
Innovation Office (TIO) under Contract Numbers 68-W-99-003 and 68-W-02-034. Information in this report is
derived from numerous sources (including personal communications with experts in the field), some of which have
been peer-reviewed. This study has undergone EPA and external review by subject-matter experts. Mention of
trade names or commercial products does not constitute endorsement or recommendation for use.

A PDF version of Arsenic Treatment Technologies for Soil, Waste, and Water, is available for viewing or
downloading from the Hazardous Waste Cleanup Information (CLU-IN) system web site at http://clu-in.org/arsenic.
A limited number of printed copies are available free of charge, and may be ordered via the web site, by mail or by
facsimile from:

U.S. EPA/National Service Center for Environmental Publications (NSCEP)
P.O. Box 42419
Cincinnati, OH 45242-2419
Telephone: (513) 489-8190 or (800) 490-9198
Fax: (513)489-8695
                                       ACKNOWLEDGMENTS

Special acknowledgment is given to the federal and state staff and other remediation professionals for providing
information for this document.  Their cooperation and willingness to share their expertise on arsenic treatment
technologies encourages their application at other sites. Contributors to the report included: U.S. EPA Office of
Groundwater and Drinking Water; U.S. EPA National Risk Management Research Laboratory; U.S. EPA Office of
Emergency and Remedial Response; U.S. EPA Office of Solid Waste; U.S. EPA Region I; U.S. EPA Region III;
David Ellis and Hilton Frey of Dupont; Richard M. Markey and James C. Redwine of Southern Company; James D.
Navratil of Clemson University; Robert G. Robbins of the Aquamin Science Consortium International; Cindy
Schreier of Prima Environmental; David Smythe of the University of Waterloo; Enid J. "Jeri" Sullivan of the Los
Alamos National Laboratory; and G. B. Wickramanayake of the Battelle Memorial Institute.
                                                  VI

-------
        PART I
OVERVIEW AND FINDINGS

-------

-------
1.0
EXECUTIVE SUMMARY
This report contains information on the current state of
the treatment of soil, waste, and water containing ;
arsenic, a contaminant that can be difficult to treat and
may cause a variety of adverse health effects in hiimans.
This information can help managers at sites with  ;
arsenic-contaminated media, generators of arsenic^
contaminated waste and wastewater, and owners and
operators of drinking water treatment plants to:

•   Identify.proven and effective arsenic treatment
    technologies                              ':
    Screen those technologies based on effectiveness,
    treatment goals, application-specific characteristics,
    and cost
    Apply experience from sites with similar treatment
    challenges.                                ;
•   Find more detailed arsenic treatment information

Arsenic is in many industrial raw materials, products,
and wastes, and is a contaminant of concern in soil and
groundwater at many remediation sites.  Because  ,
arsenic readily changes valence state and reacts to1 form
species with varying toxicity and mobility, effective
treatment of arsenic can be difficult. Treatment can
result in residuals that, under some environmental
conditions, become more toxic and mobile. In addition,
the recent reduction in the maximum contaminant level
(MCL) for arsenic in drinking water from 0.050 to
0.010 mg/L will impact technology selection and
application for drinking water treatment, and could
result in lower treatment goals for remediation of \
arsenic-contaminated sites. A lower treatment goal may
affect the selection, design, and operation of arsenic
treatment systems.                              i

This report identifies 13 technologies to treat arsenic in
soil, waste, and water. Table 1.1 provides brief  •
descriptions of these technologies. Part II of this report
contains more detailed information about each   "
technology.                                   '  •

Table 1.2 summarizes the technology applications and
performance identified for this report.  The table  i
provides information on the number of projects that met
certain current or revised regulatory standards,   !  ,
including the RCRA regulatory threshold for the  !
toxicity characteristic of 5.0 mg/L leachable arsenic, the
former MCL of 0.050 mg/L arsenic, and the revised
MCL of 0.010 mg/L.  The table presents information for
solid-phase media (soil and waste) and aqueous media
(water, including groundwater, surface water, drinking
water, and wastewater).  The technologies used to^treat
one type of media typically show similar applicability
and effectiveness when applied to a similar media; For
example, technologies used to treat arsenic in soil have
about the same applicability and effectiveness, and are
used with similar frequency, to treat solid industrial
wastes. Similarly, technologies used to treat one type
of water (e.g., groundwater) typically show similar
applicability, effectiveness, and frequency of use when
treating another type of water (e.g., surface water).

Soil and Waste Treatment Technologies

In general, soil and waste are treated by immobilizing
the arsenic using solidification/stabilization (S/S).  This
technology is usually capable of reducing the
teachability of arsenic to below 5.0 mg/L (as measured
by the toxicity characteristic leaching procedure
[TCLP]), which is a common treatment goal for soil and
waste. S/S is generally the least expensive technology
for treatment of arsenic-contaminated soil and waste.

Pyrometallurgical processes are applicable to some soil
and waste from metals mining and smelting industries.
However, the information gathered for this report did
not indicate any current users of these technologies for
arsenic in the U. S.  Other soil and waste treatment
technologies, including vitrification, soil washing/acid
extraction, and soil flushing, have had only limited
application to the treatment of arsenic. Although these
technologies may be capable of effectively treating
arsenic, data on performance are limited. In addition,
these technologies tend to be more expensive than S/S.

Water Treatment Technologies

Based on the information gathered for this report,
precipitation/coprecipitation is frequently used to treat
arsenic-contaminated water, and is capable of treating a
wide range of influent concentrations to the revised
MCL for arsenic. The effectiveness of this technology
is less likely to be reduced by characteristics and
contaminants other than arsenic, compared to other
water treatment technologies. It is also capable of
treating water characteristics or contaminants other than
arsenic, such as hardness or heavy metals.  Systems
using this technology generally require skilled
operators; therefore, precipitation/coprecipitation is
more cost effective at a large scale where labor costs
can be spread over a larger amount of treated water
produced.

The effectiveness of adsorption and ion exchange for
arsenic treatment is more likely than precipitation/
coprecipitation to be affected by characteristics and
contaminants other than arsenic. However, these
technologies are capable of treating arsenic to the
revised MCL. Small capacity systems using these
technologies tend to have lower operating and
maintenance costs, and require less operator expertise.
Adsorption and ion exchange tend to be used more
often when arsenic is the only contaminant to be
treated, for relatively smaller systems, and as a
polishing technology for the effluent from larger
systems. Membrane filtration is used less frequently
                                                    1-1

-------
because it tends to have higher costs and produce a
larger volume of residuals than other arsenic treatment
technologies.

Innovative Technologies

Innovative technologies, such as permeable reactive
barriers, biological treatment, phytoremediation, and
electrokinetic treatment, are also being used to treat
arsenic-contaminated soil, waste, and water. The
references identified for this report contain information
about only a few applications of these technologies at
full scale. However, they may be used to treat arsenic
more frequently in the future. Additional treatment data
are needed to determine their applicability and
effectiveness.

Permeable reactive barriers are used to treat
groundwater in situ.  This technology tends to have
lower operation and maintenance costs than ex situ
(pump and treat) technologies, and typically requires a
treatment time of many years. This report identified
three full-scale applications of this technology, but
treatment data were available for only one application.
In that application, a permeable reactive barrier is
treating arsenic to below the revised MCL.

Biological treatment for arsenic is used primarily to
treat water above-ground in processes that use
microorganisms to enhance precipitation/
coprecipitation. Bioleaching  of arsenic from soil has
also been tested on a bench scale. This technology may
require pretreatment or addition of nutrients and other
treatment agents to encourage the growth of key
microorganisms.

Phytoremediation is an in situ technology intended to be
applicable to soil, waste, and water. This technology
tends to have low capital, operating, and maintenance
costs relative to other arsenic  treatment technologies
because it relies on the activity and growth of plants.
However, the effectiveness of this technology may be
reduced by a variety of factors, such as the weather, soil
and groundwater contaminants and characteristics, the
presence of weeds or pests, and other factors. The
references identified for this report contained
information on one full-scale  application of this
technology to arsenic treatment.

Electrokinetic treatment is an hi situ technology
intended to be applicable to soil, waste and water.  This
technology is most applicable to fine-grained soils, such
as clays.  The references identified for this report
contained information on one full-scale application of
this technology to arsenic treatment.
                                                    1-2

-------
               Table 1.1
Arsenic Treatment Technology Descriptions
Technology
Description
Technologies for Soil and Waste Treatment
Solidification/
Stabilization
Vitrification
Soil Washing/
Acid Extraction
Pyrometallurgical
Recovery
In Situ Soil
Flushing
Physically binds or encloses Contaminants within a stabilized mass and chemically reduces the
hazard potential of a waste by converting the contaminants into less soluble, mobile, or toxic
forms.
High temperature treatment that reduces the mobility of metals by incorporating them into a
chemically durable, leach resistant, vitreous mass. The process also may cause contaminants
to volatilize, thereby reducing their concentration in the soil and waste.
An ex situ technology that takes advantage of the behavior of some contaminants to
preferentially adsorb onto the fines fraction of soil. The soil is suspended in a wash solution
and the fines are separated from the suspension, thereby reducing the contaminant
concentration in the remaining soil.
Uses heat to convert a contaminated waste feed into a product with a high concentration of the
contaminant that can be reused or sold.
Extracts organic and inorganic contaminants from soil by using water, a solution of chemicals
in water, or an organic extrattant, without excavating the contaminated material itself. The
solution is injected into or sprayed onto the area of contamination, causing the contaminants
to become mobilized by dissolution or emulsification. After passing through the
contamination zone, the contaminant-bearing flushing solution is collected and pumped to the
surface for treatment, discharge, or reinjection.
Technologies for Water Treatment
Precipitation/
Coprecipitation
Membrane
Filtration
Adsorption
Ion Exchange
Permeable
Reactive Barriers
Uses chemicals to transform dissolved contaminants into an insoluble solid or form another
insoluble solid onto which dissolved contaminants are adsorbed. The solid is then removed
from the liquid phase by clarification or filtration.
Separates contaminants from water by passing it through a semi-permeable barrier or
membrane. The membrane allows some constituents to pass, while blocking others.
Concentrates solutes at the surface of a sorbent, thereby reducing their concentration in the
bulk liquid phase. The adsorption media is usually packed into a column. As contaminated
water is passed through the column, contaminants are adsorbed.
Exchanges ions held electrostatically on the surface of a solid with ions of similar charge in a
solution. The ion exchange media is usually packed into a column. As contaminated water is
passed through the column, contaminants are removed.
Walls containing reactive media that are installed across the path of a contaminated
groundwater plume to intercept the plume. The barrier allows water to pass through while the
media remove the contaminants by precipitation, degradation, adsorption, or ion exchange.
Technologies for Soil, Waste, and Water Treatment
Electrokinetic
Treatment
Phytoremediation
Biological
Treatment
Based on the theory that a low-density current applied to soil will mobilize contaminants in
the form of charged species. ; A current passed between electrodes inserted into the subsurface
is intended to cause water, ions, and particulates to move through the soil. Contaminants
arriving at the electrodes can be removed by means of electroplating or electrodeposition,
precipitation or coprecipitatibn, adsorption, complexing with ion exchange resins, or by
pumping of water (or other fluid) near the electrode.
Involves the use of plants to degrade, extract, contain, or immobilize contaminants in soil,
sediment, and groundwater. ;
Involves the use of microorganisms that act directly on contaminant species or create ambient
conditions that cause the contaminant to leach from soil or precipitate/coprecipitate from
water.
                 1-3

-------
                                                                    Table 1.2
                                                        Summary of Key Data and Findings
Technology
Solidification/Stabilization
Vitrification
Soil Washing/Acid Extraction
Pyrometallurgical Recovery
In Situ Soil Flushing
Precipitation/Coprecipitation
Membrane Filtration
Adsorption
Ion Exchange
Permeable Reactive Barriers
Electrokinetics
Phytoremediation
Biological Treatment
Media Treated
Soil
and
Waste
+
4-
4.
+ •
4-
-
-
.
-
-
+
4-
4-
Water
-
-
-
-
-
4-
' 4-
4-
4-
4-
4-
4-
4-
Number of Applications Identified"
(Number with Performance Data)
Bench
Scale
NC
NC
2(0)
0
0
NC
6(0)
NC
NC
5(4)
3(0)
4(0)
1
Pilot
Scale
10 (10)
10(5)
3(0)
0
2(0)
24 (22)
25(2)
7(4)
0
2(1)
3(1)
2(0)
3(2)
Full
Scale
34 (32)
6(2)
4(0)
4(2)
2(0)
45 (30)
2(2)
14(8)
7(4)
3(1)
1(0)
1(0)
1(0)
Total
44 (42)
16(7)
9(0)
4(2)
' 4(0)
68(51)
33(4)
21 (12)
7(4)
10(6)
7(1)
7(0)
5(2)
Soil and Waste
Number of
Applications
Achieving <5.0
mg/L Leachable
Arsenic
37
7 .
-
2 '
-
-
-
-
-
-
-
-
-
Water
Number of
Applications
Achieving <0.050
mg/L Arsenic
-
-
• -
-'
-
36
4
• 12
3
6
1
-
1
Number of
Applications
Achieving
<0.010 mg/L
Arsenic
-
-
- '
-
-
19
2
7
2
4
0
-
0
a   Applications were identified through a search of available technical literature (See Sections 2.9 and 2.10). The number of applications include only those
    identified during the preparation of this report, and are not comprehensive. Limited information on treatment of industrial wastes and wastewaters was -
    identified, therefore the table may not be representative of these types of applications.
NC = Data not collected           -  = Not applicable
Source: Adapted from data in Sections 4.0 to 16.0 of this report
                                                                       1-4

-------
2.0 INTRODUCTION

2.1 Who Needs to Know about Arsenic Treatment
    Technologies?                             ,

This report was prepared to provide information ori the
current state of arsenic treatment for soil, waste, and
water.  The report may be used to:

• Identify proven and effective arsenic treatment  '
  technologies
• Screen those technologies based on effectiveness,
  treatment goals, application-specific characteristics,
  and cost                                    ;
• Apply experience from sites with similar treatment
  challenges                                  I
• Find more detailed arsenic treatment information

The report may be used by remediation site managers,
hazardous waste generators (for example, wood treaters,
herbicide manufacturers, mine and landfill operators),
drinking water treatment plant designers and operators,
and the general public to help screen arsenic treatment
options.    .                                   j

Arsenic is a  common inorganic element found widely in
the environment.  It is in many industrial products,
wastes, and wastewaters, and is a contaminant of  ;
concern at many remediation sites.  Arsenic-      ;
contaminated soil, waste, and water must be treated by
removing the arsenic or immobilizing it.  Because
arsenic readily changes valence states and reacts tq
form species with varying toxicity and mobility,   j
effective, long-term treatment of arsenic can be    ,
difficult. In some disposal environments arsenic h^s
leached from arsenic-bearing wastes at high       |
concentrations (Ref. 2.11).

Recently, the EPA reduced the maximum contaminant
level (MCL) for arsenic in drinking water from 0.050
mg/L to 0.010 mg/L, effective in 2006 (Ref. 2.9).  ;
Drinking water suppliers may need to add new    ;
treatment processes or retrofit existing treatment   ;
systems to meet the revised MCL.  In addition, it may
affect Superfund remediation sites and other sites that
base cleanup goals on the arsenic drinking water MCL.
This report provides information needed to help meet
the challenges of arsenic treatment.              j

2.2 Background

Where Does Arsenic Come From?

Arsenic occurs naturally in rocks, soil, water, air,,
plants, and animals. Natural activities such as volcanic
action, erosion of rocks, and forest fires, can release
arsenic into the environment. Industrial products
containing arsenic include wood preservatives, paints,
dyes, Pharmaceuticals, herbicides, and semi-
conductors.  The man-made sources of arsenic in the
environment include mining and smelting operations;
agricultural applications; burning of fossil fuels and
wastes; pulp and paper production; cement
manufacturing; and former agricultural uses of arsenic
(Ref. 2.1).

What Are the Health Effects of Arsenic?

Many studies document the adverse health effects in
humans exposed to inorganic arsenic compounds.  A
discussion of those effects is available in the following
documents:

•   National Primary Drinking Water Regulations;
    Arsenic and Clarifications to Compliance and New
    Source Contaminants Monitoring (66 FR 6976 /
    January 22, 2001) (Ref. 2.1)
•   The Agency for Toxic Substances and Disease
    Registry (ATSDR) ToxFAQs™ for Arsenic (Ref.
    2.13).

How Does Arsenic Chemistry Affect Treatment?

Arsenic is a metalloid or inorganic semiconductor that
can form inorganic and organic compounds.  It occurs
with valence states of-3, 0, +3 (arsenite), and +5
(arsenate). However, the valence states of-3 and 0
occur only rarely in nature.  This discussion of arsenic
chemistry focuses on inorganic species of As(III) and
As(V).  Inorganic compounds of arsenic include
hydrides  (e.g., arsine), halides, oxides, acids, and
sulfides (Ref. 2.4).

The toxicity and mobility of arsenic varies with its
valence state and chemical form.  Arsenite and arsenate
are the dominant species in surface water and sea water,
and organic arsenic species can be found in natural gas
and shale oil (Ref. 2.12).  Different chemical
compounds containing arsenic exhibit varying degrees
of toxicity and solubility.

Arsenic readily changes its valence state and chemical
form in the environment.  Some conditions that may
affect arsenic valence and speciation include (Ref. 2.7):

    •   pH - in the pH range of 4 to 10, As(V) species
        are negatively charged in water, and the
        predominant As(III) species is neutral in
        charge
    •   redox potential
        the presence of complexing ions, such as ions
        of sulfur, iron, and calcium
    •   microbial activity

Adsorption-desorption reactions can also affect the
mobility of arsenic in the environment. Clays,
                                                   2-1

-------
carbonaceous materials, and oxides of iron, aluminum,
and manganese are soil components that may participate
in adsorptive reactions with arsenic (Ref. 2.7).

The unstable nature of arsenic species may make it
difficult to treat or result in treated wastes whose
toxicity and mobility can change under some
environmental conditions. Therefore, the successful
treatment and long-term disposal of arsenic requires an
understanding of arsenic chemistry and the disposal
environment.

2.3 How Often Does Arsenic Occur in Drinking
    Water?

Arsenic is a fairly common environmental contaminant.
Both groundwater (e.g., aquifers) and surface water
(e.g., lakes and rivers) sources of drinking water can
contain arsenic. The levels of arsenic are typically
higher in groundwater sources. Arsenic levels in
groundwater tend to vary geographically.  In the U.S.,
Western states (AK, AZ, CA, ID, NV, OR, UT, and
WA) tend to have the highest concentrations (>0.010
mg/L), while states in the North Central (MT, ND, SD,
WY), Midwest Central (TL, IN, IA, MI, MN, OH, and
WI), and New England (CT, MA,  ME, NH, NJ, NY, RI,
and VT) regions tend to have low to moderate
concentrations (0.002 to 0.010 mg/L). However, some
portions of these areas may have no detected arsenic in
drinking water. Other regions of the U.S. may have
isolated areas of high concentration. EPA estimates that
4,000 drinking water treatment systems may require
additional treatment technologies,  a retrofit of existing
treatment technologies, or other measures to achieve the
revised MCL for arsenic. An estimated 5.4% of
community water systems (CWSs) using groundwater
as a drinking water source and 0.7% of CWSs using
surface water have average  arsenic levels above 0.010
mg/L. (Ref. 2.1)

2.4 How Often Does Arsenic Occur at Hazardous
    Waste Sites?

Hazardous waste sites fall under several clean-up
programs, such as Superfund, Resource Conservation
and Recovery Act (RCRA)  corrective actions, and state
cleanup programs.  This section contains information
on the occurrence and treatment of arsenic at National
Priorities List (NPL) sites, known  as Superfund sites.
Information on arsenic occurrence and treatment at
Superfund sites was complied from the CERCLIS 3
database (Ref. 2.3), the Superfund NPL Assessment
Program (SNAP) database,  and the database supporting
the document "Treatment Technologies for Site
Cleanup: Annual Status Report (Tenth Edition)" (Ref.
2.8). The information sources identified for this report
did not contain information on arsenic occurrence and
treatment at RCRA corrective action and state cleanup
program sites.

Table 2.1 lists the number of Superfund sites with
arsenic as a contaminant of concern by media.
Groundwater and soil were the most common media
contaminated with arsenic at 380 and 372 sites,
respectively.  The number of sites in Table 2.1 exceeds
the number of total sites with arsenic contamination
(568) because each site may have more than one type of
media contaminated with arsenic.

                    Table 2.1
    Number of Superfund Sites with Arsenic as a
         Contaminant of Concern by Media
Media Type
Groundwater
Soil
Sediment
Surface Water
Debris
Sludge
Solid Waste
Leachate
Other
Liquid Waste
Air
Residuals
Number of Sites
380
372
154
86
77
45
30
24
21
12
8
1
                 Source: Ref. 2.3

Arsenic occurs frequently at NPL sites.  Figure 2.1
shows the most common contaminants of concern
present at Superfund sites for which a Record of
Decision (ROD) has been signed, through FY 1999, the
most recent year for which such information is
available. Arsenic is the second most common
contaminant of concern (after lead), occurring at 568
sites (47% of all sites on the NPL with RODs).
                                                 2-2

-------
     700
     600
     500
  |  400.
 I  300
  S
 J!
     200 i
     100.
                                                Figure 2.1
                         , Top Twelve Contaminants of Concern at Superfund Sites
591
 S
I
                   568
                           529
                                   518
                        'Vป'
                        *mj!
                        iVซ'
                        m
                                   a*
                                   fsfi
                                           457
                                                           384

                                                                        373
                                                                                           357
I
53?

                                                                                           m
                                             Source: Ref. 2.3
Table 2.2 lists the number of Superfund sites with
arsenic as a contaminant of concern by site type.  The
most common site types were landfills and other  . I
disposal facilities, chemicals and allied products,  and
lumber and wood products.  Some sites may have more
than one site type.                             i

Figure 2.2 shows the use of treatment technologies;to
address arsenic at Superfund sites. These projects may
be planned, ongoing, or completed.  Solidification/;
stabilization was the most common treatment     !
technology for soil and waste, used in 45 projects tp
treat arsenic.  The most common treatment technology
for water was precipitation/coprecipitation, which is
known to have been used in nine projects.        j
                                            More detail on these applications is provided in the
                                            technology-specific sections (Sections 4.0 through
                                            16.0).  Information in Figure 2.2 on the treatment of
                                            contaminant sources (i.e., contaminated soil, sludge,
                                            sediment, or other environmental media excluding
                                            groundwater) and in situ groundwater treatment is
                                            based on a detailed review of RODs and contacts with
                                            RPMs.  A similar information source for pump and treat
                                            technologies (precipitation/coprecipitation, membrane
                                            filtration, adsorption, ion exchange) for groundwater
                                            containing arsenic at Superfund Sites was not available.
                                                  2-3

-------
                     Table 2.2
   Number of Superfund Sites with Arsenic as a
       Contaminant of Concern by Site Type
                    Figure 2.2
   Number of Applications of Arsenic Treatment
         Technologies at Superfund Sites"
Site Type
Landfills and Other Disposal
Chemicals and Allied Products
Lumber and Wood Products
Groundwater Plume Site
Metal Fabrication and Finishing
Batteries and Scrap Metal
Military and Other Ordnance
Transportation Equipment
Primary Metals Processing
Chemicals and Chemical Waste
Ordnance Production
Electrical Equipment
Radioactive Products
Product Storage and Distribution
Waste Oil and Used Oil
Metals
Drums and Tanks
Transportation
Research and Development
Other*
Number of
Sites"
209
42
33
26
20
18
18
15
14
12
12
11
9
8
8
6
6
5
5
104
Sources:    Ref. 2.3,2.15

a   Includes site types with fewer than 5 sites, sites
    whose site types were identified as "other"or
    "multiple", and unspecified industrial waste
    facilities.
b   Some sites have more than one site type.
                                                              Solidification/Stabilization
                                                                          Vitrification
                                                           Soil Washing/Acid Extraction
                                                            Pyrometallurgical Recovery
                                                                   In Situ Soil Flushing
                                                            Precipitation/Coprecipitation
                                                                   Membrane Filtration
                                                                           Adsorption
                                                                         Ion Exchange
                                                            Permeable Reactive Barriers
                                                                  Biological Treatment
                                                                        Electrokinetics
                                                                     Phytoremediation
                               il
                               12
                               11
                               12
                               HH9
                               0
                               m5
                                                           Information on the application of groundwater
                                                           pump and treat technologies, including
                                                           precipitation/coprecipitation, membrane filtration,
                                                           adsorption, and ion exchange, is based on available
                                                           data and is not comprehensive.
2.5 What Are the Structure and Contents of the
Report?

Part I of this report, the Overview and Findings,
contains an Executive Summary, an Introduction, and a
Comparison of Arsenic Treatment Technologies. This
Introduction describes the purpose of the report,
presents background information, and summarizes the
methodology used to gather and analyze data. The
"Comparison of Technologies" Section (3.0) analyzes
and compares the data gathered.

Part II of this report contains 13 sections, each
summarizing the available information for an arsenic
treatment technology. Each summary includes a brief
description of the technology, information about how it
is used to treat arsenic,  its status and scale, and
available cost and performance data, including the
amount and type of soil, waste, and water treated and a
summary of the results of analyses of untreated soil,
waste, and water and treatment residuals for total and
leachable arsenic concentrations.  The technology
summaries are organized as follows: the technologies
typically used to treat soil and waste appear first, in the
order of their frequency of full-scale applications,
followed by those typically used for water in the same
order, and then by those used to treat soil,  waste, and
water.
                                                   2-4

-------
2.6 What Technologies and Media Are Addressed in
the Report?

This report provides information on the 13 technologies
listed in Table 1.1. These technologies have been used
at full scale for the treatment of arsenic in soil, waste,
and water. For the purposes of this report, the term
"soil" includes soil, debris, sludge, sediments, and other
solid-phase environmental media.  Waste includes non-
hazardous and hazardous solid waste generated by
industry. Water includes groundwater, drinking water,
non-hazardous and hazardous industrial wastewater,
surface water, mine drainage, and  leachate.       '

2.7 How Is Technology Scale Defined?

This report includes available information on bench-,
pilot- and full-scale applications for the 13
technologies. Full-scale projects include those used
commercially to treat industrial wastes and those used
to remediate an entire area of contamination.  Pilotr
scale projects are usually conducted in the field to test
the effectiveness of the technology on a specific soil,
waste, and water or to obtain information for scaling a
treatment system up to full scale.  Bench-scale projects
are conducted on a small scale, usually in a laboratory
to evaluate the technology's ability to treat soil, waste,
and water. These often occur during the early phases of
technology development.                       j

The report focuses on full- and pilot-scale data. Bench-
scale data are presented only when less than 5 full-jscale
applications of a technology were  identified.  For the
technologies with at least 5 identified full-scale   1
applications (solidification/stabilization, vitrification,
precipitation/coprecipitation, adsorption, and ion  •
exchange), the report does not include bench-scale;data.

2.8 How Are Treatment Trains  Addressed?    i

Treatment trains consist of two or  more technologies
used together, either integrated into a single process or
operated as a series of treatments in sequence. The;
technologies  in a train may treat the same contaminant.
The information gathered for this report included many
projects that used treatment trains. A common    ;
treatment train used for arsenic in  water includes an
oxidation step to change arsenic from As(IH) to its less
soluble As(V) state, followed by precipitation/    !
coprecipitation and filtration to remove the precipitate.

Some trains are employed when one technology alone is
not capable of treating all of the contaminants.  For
example, at the Baird and McGuire Superfund Site
(Table 9.1), an above-ground system consisting of air
stripping, metals precipitation, and activated carbon
adsorption was used to treat groundwater contaminated
with volatile organic compounds (VOCs), arsenic, knd
semivolatile organic compounds (SVOCs). In this
treatment train the air stripping was intended to treat
VOCs, the precipitation, arsenic, and the activated
carbon adsorption, SVOCs and any remaining VOCs.

In many cases, the available information does not
specify the technologies within the train that are
intended to treat arsenic.  Influent and effluent
concentrations, where available, often were provided
for the entire train, and not the individual components.
In such cases, engineering judgement was used to
identify the technology that treated arsenic. For
example, at the Greenwood Chemical Superfund site
(Table 9.1), a treatment train consisting of metals
precipitation, filtration, UV oxidation and carbon
adsorption was used to treat groundwater contaminated
with arsenic, VOCs, halogenated VOCs, and SVOCs.
The precipitation and filtration were assumed to remove
arsenic, and the UV oxidation and carbon adsorption
were assumed to have only a negligible effect on the
arsenic concentration.

Where a train included more than one potential arsenic
treatment technology, all arsenic treatment technologies
were assumed to contribute to arsenic treatment, unless
available information indicated otherwise. For
example, at the Higgins Farm Superfund site, arsenic-
contaminated groundwater was treated with
precipitation and ion exchange (Tables 9.1 and 12.1).
Information about this treatment is presented in both the
precipitation/coprecipitation (Section 9.0) and ion
exchange (Section 12.0) sections.

Activated carbon adsorption is most commonly used to
treat organic contaminants. This technology is
generally ineffective  on As(III) (Ref. 2.14). Where
treatment trains included activated carbon adsorption
and another arsenic treatment technology, it was
assumed that activated carbon adsorption did not
contribute to the arsenic treatment, unless the available
information indicated otherwise.

2.9 What Are the Sources of Information for This
Report?

This report is based on an electronic literature search
and information gathered from readily-available data
sources, including:

        Documents and databases prepared by EPA,
        DOD, and DOE
    •   Technical literature
    •   Information supplied by vendors of treatment
        technologies
    •   Internet sites
    •   Information from technology experts
                                                   2-5

-------
Most of the information sources used for this report
contained information about treatments of
environmental media and drinking water.  Only limited
information was identified about the treatment of
industrial waste and wastewater containing arsenic.
This does not necessarily indicate that treatment
industrial wastes and wastewater containing arsenic
occurs less frequently, because data on industrial
treatments may be published less frequently.

The authors and reviewers of this report identified these
information sources based on their experience with
arsenic treatment.  In addition, a draft version of this
report was presented at the U.S. EPA Workshop on
Managing Arsenic Risks to the Environment, which
was held in Denver, Colorado in May of 2001.
Information gathered from this workshop and sources
identified by workshop attendees were also reviewed
and incorporated where appropriate. Proceedings for
this workshop may be available from EPA in 2002.

2.10 What Other Types of Literature Were
Searched and Referenced for This Report?

To identify recent and relevant documents containing
information on the application of arsenic treatment
technologies in addition to the sources listed in Section
2.9, a literature search was conducted using the
Dialogฎ and Online Computer Library Center (OCLC)
services. The search was limited to articles published
between January 1, 1998 and May 30, 2001  in order to
ensure that the information gathered was current. The
search  identified documents that included in their title
the words "arsenic," "treatment," and one of a list of
key words intended to encompass the types of soil,
waste,  and water containing arsenic that might be
subject to treatment. Those key words were:
     • Waste
     • Sludge
     • Mining
     • Groundvvater
     • Hazardous
     • Sediment
- Water
-Mine
- Debris
-Soil
- Toxic
-Slag
The Dialogฎ search identified 463 references, and the
OCLC search found 45 references. Appendix A lists
the title, author, and publication source for each of the
508 references identified through the literature search.
The search results were reviewed to identify the
references (in English) that provided information on the
treatment of waste that contains arsenic using one of the
technologies listed in Table 1.1. Using this
methodology, a total of 44 documents identified
through the literature search were obtained and
reviewed in detail to gather information for this report.
These documents are identified in Appendix A with an
asterisk (*).
2.11    References

2.1  U.S. EPA. National Primary Drinking Water
     Regulations; Arsenic and Clarifications to
     Compliance and New Source Contaminants
     Monitoring; Proposed Rule. Federal Register, Vol
     65, Number 121, p. 38888. June 22, 2000.
     http://www.epa.gov/safewater/ars/arsenic.pdf.

2.2  U.S. Occupational Safety and Health
     Administration. Occupational Safety and Health
     Guidelines for Arsenic, Organic Compounds (as
     As). November, 2001.
     http://www.osha-slc.gov/SLTC/healthguidelines/
     arsenic/recognition.html.

2.3  U.S. EPA Office of Emergency and Remedial
     Response. Comprehensive Environmental
     Response Compensation and Liability Information
     System database (CERCLIS 3). October 2001.

2.4  Kirk-Othmer. "Arsenic and Arsenic Alloys." The
     Kirk-Othemer Encyclopedia of Chemical
     Technology, Volume 3. John Wiley and Sons,
     New York.  1992.

2.5  Kirk-Othmer. "Arsenic Compounds"  The Kirk-
     Othemer Encyclopedia of Chemical Technology,
     Volume 3. John Wiley and Sons, New York.
     1992.

2.6  EPA. Treatment Technology Performance and
     Cost Data for Remediation of Wood Preserving
     Sites. Office of Research and Development.
     EPA-625-R-97-009. October 1997.
     http://epa.gov/ncepihom.

2.7  Vance, David B.  "Arsenic - Chemical Behavior
     and Treatment". October, 2001.
     http://2the4.net/arsenicart.htm.

2.8  EPA. Treatment Technologies for Site Cleanup:
     Annual Status Report (Tenth Edition). Office of
     Solid Waste and Emergency Response. EPA-542-
     R-01-004. February 2001. http://clu-in.org.

2.9  U.S. EPA. National Primary Drinking Water
     Regulations; Arsenic and Clarifications to
     Compliance and New Source Contaminants
     Monitoring; Final Rule. Federal Register,
     Volume 66, Number 14, p. 6975-7066. January
     22,2001.
     http://www.epa.gov/sbrefa/documents/pnll4f.pdf
                                                  2-6

-------
 2.10 U.S. EPA Office of Water. Fact Sheet: EPA to
      Implement 1 Oppb Standard for Arsenic in  :
      Drinking Water. EPA 815-F-01-010. October,
      2001. http://www.epa.gov/safewater/ars/   '
      ars-oct-factsheet.html.                   '•

 2.11  Federal Register. Land Disposal Restrictions:
      Advanced Notice of Proposed Rulemaking. !
      Volume 65, Number 118.  June 19, 2000. pp.
      37944.37946.                          .
      http://www.epa.gov/fedrgstr/EPA-WASTE/2000/
      June/Day- 19/fl 5392.htm                 :
                                            i
 2.12  National Research Council. Arsenic in Drinking
      Water. Washington, D.C. National Academy
      Press. 1999.                            ;
      http://www.nap.edu/catalog/6444.html     i

2.13  The Agency for Toxic Substances and Disease
     Registry (ATSDR): ToxFAQs™ for Arsenic (12).
     July, 2001.                             |
     http://www.atsdr.cdc.gov/tfacts2.html.

2.14 U.S. EPA. Cost Analyses  for Selected     :
     Groundwater Cleanup Projects: Pump and Treat
     Systems and Permeable Reactive Barriers, EPA-
     542-R-00-013, February 2001. http://clu-in.org

2.15 U.S. EPA Office of Emergency and Remedial
     Response.  Superfund NPL Assessment Program
     (SNAP) database. April 11, 2002.          ;
                                                2-7

-------

-------
3.0  COMPARISON OF ARSENIC TREATMENT
     TECHNOLOGIES                      ;

3.1  What Technologies Are Used to Treat Arsenic?

This report identifies 13 technologies applicable to
arsenic-contaminated soil, waste, and water.      !
Technologies are considered applicable if they have
been used at full scale to treat arsenic.           :
  Arsenic Treatment Technologies

  Soil and Waste Treatment Technologies
  • Solidification/          • Pyrometallurgical
    Stabilization              Recovery        '•
  • Vitrification            • In Situ Soil Flushing
  • Soil Washing/Acid                         ;
    Extraction                            -   .  ;

  Water Treatment Technologies
  • Precipitation/           • Ion Exchange
    Coprecipitation         • Permeable Reactive
  • Membrane Filtration      Barriers
  • Adsorption

  Soil, Waste, and Water Treatment Technologies
  • Electrokinetics          • Biological Treatment
  • Phytoremediation
Table 3.1 summarizes their applicability to arsenicj-
contaminated media. The media treated by these ,
technologies can be grouped into two general    ;
categories: soil and waste; and water.            :

Technologies applicable to one type of soil and waste
are typically applicable to other types. For example,
solidification/stabilization has been used to effectively
treat industrial waste, soil, sludge, and sediment.  ;
Similarly, technologies applicable to one type of water
are generally applicable to other types.  For example,
precipitation/coprecipitation has been used to    |
effectively treat industrial wastewaters, groundwater,
and drinking water.                            !

3.2  What Technologies Are Used Most Often to
Treat Arsenic?                                i

This section provides information on the number of
treatment projects identified for each technology and
estimates of the relative frequency of their application.
Figures 3.1 to 3.3 show the number of treatment
projects identified for each technology. Figure 3.1;
shows the number for technologies applicable to sQil
and waste based on available data. The most frequently
used technology for soil and waste containing arsenic is
solidification/stabilization. The available data show
that this technology can effectively meet regulatory
cleanup levels, is commercially available to treat both
soil and waste, is usually less expensive, and generates
a residual that typically does not require further
treatment prior to disposal.

Other arsenic treatment technologies for soil and waste
are typically used for specific applications.
Vitrification may be used when a combination of
contaminants are present that cannot be effectively
treated using solidification/stabilization. It has also
been used when the vitrification residual could be  sold
as a commercial product. However, vitrification
typically requires large amounts of energy, can be  more
expensive than S/S, and may generate off-gasses
containing arsenic.

Soil washing/acid extraction is used to treat soil
primarily. However, it is not applicable to all types of
soil or to waste.  Pyrometallurgical treatment has been
used primarily to recycle arsenic from industrial wastes
containing high concentrations of arsenic from metals
refining and smelting operations. These technologies
may not be applicable to soil and waste containing low
concentrations of arsenic. In situ soil flushing treats
soil in place, eliminating the need to excavate soil.
However, no performance data were identified for the
limited number of full-scale applications of this
technology to arsenic.

Figure 3.2 shows the number of treatment projects
identified for technologies applicable to water. For
water containing arsenic, the most frequently used
technology is precipitation/coprecipitation. Based on
the information gathered for this report, precipitation/
coprecipitation is frequently used to treat arsenic-
contaminated water, and is capable of treating a wide
range of influent concentrations to the revised MCL for
arsenic. The effectiveness of this technology is less
likely to be reduced by characteristics and contaminants
other than arsenic, compared to other water treatment
technologies.  It is also capable of treating water
characteristics or contaminants other than arsenic,  such
as hardness  or heavy metals.  Systems using this
technology generally require skilled operators;
therefore, precipitation/ coprecipitation is more cost
effective at a large scale where labor costs can be
spread over a larger amount of treated water produced.

The effectiveness of  adsorption and ion exchange for
arsenic treatment is more likely than precipitation/
coprecipitation to be affected by characteristics and
contaminants other than arsenic. However, these
technologies are capable of treating arsenic to the
                                                    3-1

-------
                                               Figure 3.1
         Number of Identified Applications of Arsenic Treatment Technologies for Soil and Waste
           Solidification/
           Stabilization*
                                                                         0    0
Vitrification*
 Soil Washing/     Pyrometallurgical      In Situ Soil
Acid Extraction       Recovery           Flushing
        * Bench-scale data not collected for this technology.
                                               Figure 3.2
             Number of Identified Applications of Arsenic Treatment Technologies for Water
      50
           Precipitation/
           Coprecipitation*
 Membrane
  Filtration
 Adsorption*
Ion Exchange*
Permeable Reactive
    Barriers
* Bench-scale data not collected for this technology.
                                                  3-2

-------
                                              I  Figure 3.3
      Number of Identified Applications of Arsenic Treatment Technologies for Soil, Waste, and Water
                  Electrokinetics
Phytoremediation
Biological
Treatment
revised MCL.  Small capacity systems using these
technologies tend to have lower operating and
maintenance costs, and require less operator expertise.
Adsorption and ion exchange tend to be used more
often when arsenic is the only contaminant to be
treated, for relatively smaller systems, and as a   \
polishing technology for the effluent from larger  ',
systems.  Membrane filtration is used less frequently
because it tends to have higher costs and produce a
larger volume of residuals than other arsenic treatment
technologies.                                  ;

Permeable reactive barriers are used to treat
groundwater in situ. This technology tends to have
lower operation and maintenance costs than ex situ
(pump and treat) technologies, and typically requires a
treatment time of many years. This report identified
three full-scale applications of this technology, but
treatment data were available for only one application.
In that application, a permeable reactive barrier is
treating arsenic to below the revised MCL.       [

Figure 3.3 shows the number of treatment projects
identified for technologies applicable to soil, waste, and
water. Three arsenic treatment technologies are  :
generally applicable to soil, waste, and water:    '
electrokinetics, phytoremediation, and biological
treatment.  These technologies have been applied in
only a limited number of applications.

Electrokinetic treatment is an in situ technology  ,
intended to be applicable to soil, waste and water. This
technology is most applicable to fine-grained soils, such
as clays. The references identified for this report'
     contained information on one full-scale application of
     this technology to arsenic treatment.

     Phytoremediation is an in situ technology intended to be
     applicable to soil, waste, and water.  This technology
     tends to have low capital, operating, and maintenance
     costs relative to other arsenic treatment technologies
     because it relies on the activity and growth of plants.
     However, this technology tends to be less robust. The
     references identified for this report contained
     information on  one full-scale application of this
     technology to arsenic treatment.

     Biological treatment for arsenic is used primarily to
     treat water above-ground in processes that use
     microorganisms to enhance precipitation/
     coprecipitation. Bioleaching of arsenic from soil has
     also been tested on a bench scale. This technology may
     require pretreatment or addition of nutrients and other
     treatment agents to encourage the growth of key
     microorganisms.

     3.3  What Factors Affect Technology Selection for
          Drinking Water Treatment?

     For the treatment of drinking water, technology
     selection depends on several of factors, such as existing
     systems, the need to treat for other contaminants, and
     the size of the treatment system. Although the data
     collected for this report indicate that
     precipitation/coprecipitation is the technology most
     commonly used to remove arsenic from drinking water,
     in the future other technologies may become more
                                                    3-3

-------
 common as drinking water treatment facilities modify
 their operations to meet the revised arsenic MCL.

 Precipitation/coprecipitation is often used to remove
 contaminants other than arsenic from drinking water,
 such as hardness or suspended solids. However, the
 precipitation/coprecipitation processes applied to
 drinking water usually also remove arsenic, or can be
 easily modified  to do so. Where precipitation/
 coprecipitation processes are already in place, or are
 needed to remove other contaminants, these processes
 are commonly used to remove arsenic. Where
 precipitation/coprecipitation is not needed to treat
 drinking water for other contaminants, treaters may be
 more likely to choose another technology, such as
 adsorption, ion exchange, or reverse osmosis.

 In addition, the size of a drinking water treatment
 system may affect the choice of technology.
 Precipitation/coprecipitation processes tend to be more
 complex, requiring more unit operations and greater
 operational expertise and monitoring, while adsorption
 and ion exchange units are usually less complex and
 require less operator expertise and monitoring.
 Therefore, operators of smaller drinking water treatment
 systems  are more likely to select adsorption or ion
 exchange to treat arsenic instead of precipitation/
 coprecipitation.

 3.4   How Effective Are Arsenic Treatment
      Technologies?

 Applications are considered to have performance data
 when analytical  data for arsenic are available both
 before and after  treatment. For the technologies
 applicable to soil and waste, Table  1.2 (presented in the
 Executive Summary) includes performance data only
 for those projects with leachable arsenic  concentration
 data for the treated soil and waste, and either leachable
 or total arsenic concentrations for the untreated soil and
 waste. Performance data were compared to the RCRA
 TCLP regulatory threshold of 5.0 mg/L (Ref. 3.1).  For
 this table, projects that measured teachability with other
 procedures, such as the EPT and the WET, were also
 compared directly to this level. The tables in the
 technology-specific sections (Sections 4.0 to 16.0)
 identify the leaching procedures used to measure
 performance. The text box to the right describes the
 leaching procedures most frequently identified in the
 information sources used for this report.

 For the technologies applicable to water, the
 performance was compared to the former MCL of 0.050
 mg/L, and the revised MCL of 0.010 mg/L (Ref. 3.2).
 Information was available on relatively few projects
that have treated arsenic to below 0.010 mg/L.
 However, this does not necessarily indicate that these
treatment technologies cannot achieve 0.010 mg/L
  Leaching Procedure Descriptions

  Toxicity Characteristic Leaching Procedure
  (TCLP):  The TCLP is used in identifying RCRA
  hazardous wastes that exhibit the characteristic of
  toxicity.  In this procedure, liquids are separated
  from the solid phase of the waste, and the solid
  phase is then reduced in particle size until it is '
  capable of passing through a 9.5 mm sieve. The
  solids are then extracted for 18 hours with a solution
  of acetic acid equal to 20 times the weight of the
  solid phase. The pH  of the extraction fluid is a
  function of the alkalinity of the waste. Following
  extraction, the liquid  extract is separated from the
  solid phase by filtration. If compatible, the initial
  liquid phase of the waste is added to the liquid
  extract and analyzed, otherwise they are analyzed
  separately. The RCRA TCLP regulatory threshold
  for arsenic is 5.0 mg/L in the extraction fluid (Ref.
  3.22).

  Extraction Procedure Toxicity Test (EPT): This
  procedure is similar to the TCLP test, with the
  following differences:
  •  The extraction period is 24 hours
  •  The extraction fluid is a pH 5 solution of acetic
    acid.
  The EPT was replaced by the TCLP test in March,
  1990 for purposes of hazardous waste identification,
  and is therefore no longer widely used (Ref. 3.23)

  Waste Extraction Test (WET): The WET is used
  in identifying hazardous wastes in California. This
  procedure is similar to the TCLP, with the following
  differences
  •  The solid phase is reduced in particle size until it
    is capable of passing through a 2 mm sieve.,
  •  The waste is extracted for 48  hours
  •  The extraction fluid is a pH 5 solution of sodium
    citrate equal to 10 times the weight of the solid
    phase. The WET regulatory threshold for arsenic
    is 5.0 mg/L (Ref. 3.24).
arsenic. In many cases, the treatment goal in the
projects was greater than 0.010 mg/L, and in most cases
was the previous arsenic MCL of 0.050 mg/L.  In such '
cases, the treatment technology may be capable of
meeting 0.010 mg/L arsenic with modifications to the
treatment technology design or operating parameters.

3.5  What Are Special Considerations for
     Retrofitting Existing Water Treatment
     Systems?

On January 22, 2001, EPA published a revised MCL for
arsenic in drinking water that would require public
                                                   3-4

-------
water suppliers to maintain arsenic concentrations at or
below 0.010 mg/L by 2006 (Ref. 2.9). Some 4,00p
drinking water treatment systems may require
additional treatment technologies, a retrofit of existing
treatment technologies, or other measures to achieve
this level (Ref. 2.10). In addition, this revised MQL
may affect Superfund remediation sites and other sites
that base cleanup goals on the arsenic drinking water
MCL. A lower goal could affect the selection, design,
and operation of treatment systems.

Site-specific conditions will determine the type of
changes needed to meet the revised MCL. Some
arsenic treatment systems may be retrofitted, white
other may require new arsenic treatment systems to be
designed.  In addition, treatment to lower arsenic ;
concentrations could require the use of multiple  '.
technologies in sequence. For example, a site with an
existing metals precipitation/coprecipitation systetn
may need to add another technology such as ion  ,
exchange to achieve a lower treatment goal.      ;

In some cases, a lower treatment goal might be met by
changing the operating parameters of existing systems.
For example, changing the type or amount of treatment
chemicals used, replacing spent treatment media more
frequently, or changing treatment system flow  rat^s can
reduce arsenic concentrations in the treatment system
effluent. However, such changes may increase  '
operating  costs from use of additional treatment
chemicals or media, use of more expensive treatment
chemicals or media, and from disposal of increased
volumes of treatment residuals.                 ;

Examples of technology-specific modifications that can
help reduce effluent concentrations of arsenic include:

Precipitation/Coprecipitation                   '
•     Use of additional treatment chemicals
•     Use of different treatment chemicals       ;
•     Addition of another technology to the treatnjent
      train, such as membrane filtration

Adsorption
•     Addition of an adsorption media bed       '
•     Use of a different adsorption media        :
      More frequent replacement or regeneration df
      adsorption media
•     Decrease in the flow rate of water treated
•     Addition of another treatment technology to! the
      treatment train, such as membrane filtration j
Ion Exchange                                 :
•     Addition of an ion exchange bed          :
      Use of a different ion exchange resin      i
      More frequent regeneration or replacement of ion
      exchange media
•     Decrease in the flow rate of water treated  '
•    Addition of another technology to the treatment
     train, such as membrane filtration

Membrane Filtration
•    Increase in the volume of reject generated per
     volume of water treated
•    Use of membranes with a smaller molecular
     weight cutoff
•    Decrease in the flow rate of water treated
     Addition of another treatment technology to the
     treatment train, such as ion exchange

3.6  How Do I Screen Arsenic Treatment
     Technologies?

Table 3.2 at the end of this section is a screening matrix
for arsenic treatment technologies. It can assist
decision makers  in evaluating candidate treatment
technologies by providing information on relative
availability, cost, and other factors for each technology.
The matrix is based on the Federal Remediation
Technologies Roundtable Technology (FRTR)
Treatment Technologies Screening Matrix (Ref. 3.3),
but has been tailored to treatment technologies for
arsenic in soil, waste, and water. Table 3.2 differs from
the FRTR matrix by:

     Limiting the scope of the table to the technologies
     discussed in this report.

•    Changing the information based on the narrow
     scope of this report. For example, the FRTR
     screening matrix lists the overall cost of
     adsorption as "worse" (triangle symbol) in
     comparison to other treatment technologies for
     water. However, when applied to arsenic
     treatment, the costs of the technologies discussed
     in this report may vary based on scale, water
     characteristics, and other factors. Therefore,
     adsorption costs are not necessarily higher than
     the costs of other technologies discussed in this
     report, and this technology's overall cost is rated
     as "average" (circle symbol) in Table 3.2.

•    Adding information about characteristics that can
     affect technology performance or cost.

Table 3.2 includes the following information:

•    Development Status - The scale at which the
     technology has been  applied. "F" indicates that
     the technology has been applied to a site at full
     scale.  All of the technologies have been applied
     at full scale.

•    Treatment Trains - "Y" indicates that the
     technology is typically used in combination with
     other technologies, such as pretreatment or
                                                   3-5

-------
 treatment of residuals (excluding off gas). "N"
 indicates that the technology is typically used
 independently.

 Residuals Produced - The residuals typically
 produced that may require additional
 management. "S" indicates production of a solid
 residual, "L", a liquid residual, and "V" a vapor
 residual. All of the technologies generate a solid
 residual, with the exceptions of soil flushing and
 membrane filtration, which generate only liquid
 residuals. Vitrification and pyrometallurgical
 recovery produce a vapor residual.

 O&M or Capital Intensive -This indicates the
 main cost-intensive parts of the system.  "O&M"
 indicates that the operation and maintenance costs
 tend to be high in comparison to other
 technologies. "Cap" indicates that capital costs
 tend to be high in comparison to other
 technologies. "N" indicates neither operation and
 maintenance nor capital costs are intensive.

 Availability - The relative number of vendors that
 can design, construct, or maintain the technology.
 A square indicates more than four vendors; a
 circle, two to three vendors; and a triangle, fewer
 than two vendors. All of the technologies have
 more than four vendors with the exception of
 pyrometallurgical recycling, bioremediation,
 electrokinetics, and phytoremediation, which have
 less than two.

 System Reliability/Maintainability - The expected
 reliability/maintainability of the technology.  A
 square indicates high reliability and low
 maintenance; a circle, average reliability and
 maintenance; and a triangle, low reliability and
 high maintenance. Biological treatment,
 electrokinetics, and phytoremediation are rated
 low because of the limited number of applications
 for those technologies, and indications that some
 applications were not effective.

 Overall Cost - Design, construction, and O&M
 costs of the core process that defines each
technology, plus the treatment of residuals. A
square indicates lower overall cost; a circle,
average overall cost; and a triangle, higher overall
cost.  Solidification/stabilization is rated a low
cost technology because it typically uses standard
equipment and relatively low cost chemicals  and
additives. Phytoremediation is low cost because
of the low capital expense to purchase and plant
phytoremediating species and the low cost to
maintain the plants.
 •     Characteristics That May Require Pretreatment
      or Affect Performance or Cost - The types of
      contaminants or other substances that generally
      may interfere with arsenic treatment for each
      technology.  A 'V" indicates that the presence of
      the characteristic may interfere with technology
      effectiveness or result in increased costs.
      Although these contaminants can usually be
      removed before arsenic treatment through
      pretreatment with another technology, the addition
      of a pretreatment technology may increase overall
      treatment costs and generate additional residuals
      requiring disposal.  "Other characteristics" are
      technology-specific elements which affect
      technology performance, cost, or both.  These
      characteristics are described in Sections 4.0
      through 16.0.

 The selection of a treatment technology for a particular
 site will depend on many site-specific factors; thus the
 matrix is not intended to be used as the sole basis for
 treatment decisions.

 More detailed information on selection and design of
 arsenic treatment systems for small drinking water
 systems is available in the document "Arsenic
 Treatment Technology Design Manual for Small
 Systems " (Ref. 3.25).

 3.7 What Does Arsenic Treatment Cost?

 A limited amount of cost data on arsenic treatment was
 identified for this report.  Table 3.3 summarizes this
 information.  In many cases, the cost information was
 incomplete. For example, some data were for operating
 and maintenance (O&M) costs only, and did not specify
 the associated capital costs.  In other cases, a cost per
 unit of soil, waste, and water treated was provided, but
 total costs were not.  For some technologies, no arsenic-
 specific cost data were identified.

 The cost data were taken from a variety of sources,
 including EPA, DoD, other government sources, and
 information from technology vendors. The quality of
 these data varied, with some sources providing detailed
 information about the items included in the costs, while
 other sources gave little detail about their basis.  In
 most cases, the particular year for the costs were not
provided.  The costs in Table 3.3 are the costs reported
 in the identified references, and are not adjusted for
 inflation. Because of the  variation in type of
 information and quality, this  report does not provide a
 summary or interpretation of the costs in Table 3.3.

In general, Table 3.3 only includes costs specifically for
treatment of arsenic.  Because arsenic treatment is very
waste- and site-specific, general technology cost
estimates are unlikely to accurately predict arsenic
                                              3-6

-------
treatment costs.  However, general technology cost
estimates were included for three technologies:
solidification/stabilization, pyrometallurgical recovery,
and phytoremediation.                          ,

One of the solidification/stabilization costs listed ih
Table 3.3 is a general cost for treatment of metals, ,and
is not arsenic-specific.  This cost was included because
solidification/stabilization processes for arsenic are
similar to those for treatment of metals. The only cost
for pyrometallurgical recovery listed in Table 3.3 is a
general cost for the treatment of volatile metals and is
not arsenic-specific. This cost was included because
arsenic is expected to behave in a manner similar to
other volatile metals when treated using          ;
pryometallurgical recovery processes. For
phytoremediation, costs for applications to metals and
radionuclides are included due to the lack of data on
arsenic.

The EPA document "Technologies and Costs for  '.
Removal of Arsenic From Drinking Water" (Ref. 3.4)
contains  more information on the cost to reduce the
concentration of arsenic in drinking water from the
former MCL of 0.050 mg/L to below the  revised TylCL
of 0.010  mg/L.  The document includes capital and
O&M cost curves for a variety of processes, including:

•    Retrofitting of existing precipitation/       :
     coprecipitation processes to improve arsenic!
     removal (enhanced coagulation/filtration and
     enhanced lime softening)                  ;
     Precipitation/coprecipitation followed by
     membrane filtration (coagulation-assisted
     microfiltration)
•    Ion exchange (anion exchange) with varying
     levels of sulfate in the influent             i
     Two types of adsorption (activated  alumina at
     varying influent pH and greensand filtration)
     Oxidation pretreatment technologies (chlorination
     and potassium permanganate)
•    Treatment and disposal costs of treatment   ;
     residuals (including mechanical and
     non-mechanical sludge dewatering)
•    Point-of-use systems using adsorption (activated
     alumina) and membrane filtration (reverse   ;
     osmosis)                                 i

The EPA cost curves are  based on computer cost  ;
models for drinking water treatment systems. Costs for
full-scale reverse osmosis, a common type of menjibrane
filtration, were not included because it generally is
more expensive and generates larger volumes of  '
treatment residuals than other arsenic treatment   i
technologies  (Ref. 3.4). Although the cost information
is only for the removal of arsenic from drinking water,
many of the same treatment technologies can be used
for the treatment of other waters and may have similar
costs.

Table 3.4 presents estimated capital and annual O&M
costs for four treatment technologies based on cost
curves presented in "Technologies and Costs for
Removal of Arsenic From Drinking Water":

1.    Precipitation/coprecipitation followed by
     membrane filtration (coagulation-assisted
     microfiltration)
2.    Adsorption (greensand filtration)
3.    Adsorption (activated alumina with pH of 7 to 8 in
     the influent)
4.    Ion exchange (anion exchange with <20 mg/L
     sulfate in the influent)

The table presents the estimated costs for three
treatment system sizes: 0.01, 0.1, and 1 million gallons
per day (mgd). The costs presented in Table 3.4 are for
specific technologies listed in the table, and do not
include costs for oxidation pretreatment or management
of treatment residuals. Detailed descriptions of the
assumptions used to generate the arsenic treatment
technology cost curves are available (Ref. 3.4).

3.8  References

3.1  Code of Federal Regulations, Title 40, Part
     261.24.
     http://lula.law.cornell.edu/cfr/
3.2  U.S. EPA Office of Water. Fact Sheet: EPA To
     Implement lOppb Standard for Arsenic in
     Drinking Water. EPA815-F-01-010. October,
     2001.  http://
     www.epa.gov/safewater/ars/ars-oct-factsheet.html
3.3  Federal Remediation Technologies Reference
     Guide and Screening Manual, Version 4.0.
     Federal Remediation Technologies Roundtable.
     September 5,2001.
     http://www.frtr.gov/matrix2/topjage.html.
3.4  U.S. EPA. Office of Water. Technologies and
     Costs for Removal of Arsenic From Drinking
     Water. EPA-R-00-028. December 2000.
     http://www.epa.gov/safewater/ars/
     treatments_and_costs.pdf
3.5  U.S. EPA Office of Research and Development.
     Engineering Bulletin, Technology Alternatives  for
     the Remediation of Soils  Contaminated with
     Arsenic, Cadmium, Chromium, Mercury, and
     Lead.  Cincinnati, OH. March 1997.
     http://www.epa.gov/ncepi/Catalog/
     EPA540S97500.html
3.6  Redwine, J.C.  Successful In Situ Remediation
     Case Histories: Soil Flushing And
     Solidification/Stabilization With Portland Cement
     And Chemical Additives. Southern Company
     Services, Inc. Presented at the Air and Waste
                                                   3-7

-------
      Management Association's 93rd Annual
      Conference and Exhibition, Salt Lake City, June
      2000.
 3.7   Miller JP. In-Situ Solidification/Stabilization of
      Arsenic Contaminated Soils. Electric Power
      Research Institute.  Report TR-106700. Palo
      Alto, CA. November 1996.
 3.8   Federal Remediation Technologies Roundtable
      (FRTR). In Situ Vitrification at the Parsons
      Chemical/ETM Enterprises Superfund Site Grand
      Ledge, Michigan. April 17,2001
      http://www.frtr.gov/costperf.htm
 3.9   U.S. EPA. Treatment Technologies for Site
      Cleanup: Annual Status Report (Tenth Edition).
      Office of Solid Waste and Emergency Response.
      EPA-542-R-01-004. February 2001.
      http://clu-in.org/asr.
 3.10  U.S. EPA. Contaminants and Remedial Options
      at Selected Metal-Contaminated Sites.  Office of
      Research and Development.  EPA-540-R-95-512.
      July 1995.
 3.11  U.S. EPA. Database for EPA REACH IT
      (REmediation And CHaracterization Innovative
      Technologies). March 2001.
      http://www.epareachit.org.
 3.12  U.S. EPA. Treatment Technology Performance
      and Cost Data for Remediation of Wood
      Preserving Sites. Office of Research and
      Development. EPA-625-R-97-009. October
      1997.
      http://www.epa.gov/ncepi/Catalog/
      EPA625R97009.html
 3.13  E-mail attachment sent from Doug Sutton of
      Geotrans, Inc. to Linda Fiedler, U.S. EPA. April
      20,2001.
 3.14  E-mail attachment sent from Anni Loughlin of
      U.S. EPA Region I to Linda Fiedler, U.S. EPA.
     August 21,2001.
 3.15  Miller JP, Hartsfield TH, Corey AC, Markey RM.
      In Situ Environmental Remediation of an
      Energized Substation. EPRI. Palo Alto, CA.
      Report No. 1005169.2001.
3.16 Twidwell, L.G., et al. Technologies and Potential
     Technologies for Removing Arsenic from Process
     and Mine Wastewater.  Presented at
     "REWAS'99." San Sebastian, Spam. September
      1999. http://www.mtech.edu/metallurgy/arsenic/
     REWASAS%20for%20proceedings99ฐ/o20in
     %20word.pdf
3.17 U.S. EPA. Arsenic Removal from Drinking
     Water by Ion Exchange and Activated Alumina
     Plants.  EPA-600-R-00-088.  Office of Research
     and Development. October 2000.
 3.18 DOE.  Permeable Reactive Treatment (PeRT)
     Wall for Rads and Metals. Office of
     Environmental Management, Office of Science
     and Technology. DOE/EM-0557. September,
     2000.  http://apps.apps.em.doe.gov/ost/pubs/
     itsrs/itsr2155.pdf
 3.19 Applied Biosciences. June 28,2001.
     http://www.bioprocess.com
 3.20 Center for Bioremediation at Weber State
     University. Arsenic Treatment Technologies.
     August 27, 200.  http://www.weber.edu/
     Bioremediation/arsenic.htm..
 3.21 Electric Power Research Institute. Electrokinetic
     Removal of Arsenic from Contaminated Soil:
     Experimental Evaluation.  July 2000.
     http://www.epri.com/
     OrderableitemDesc.asp?product_id.
 3.22 U.S. EPA. SW-846 On-Line. Test Methods for
     Evaluating Solid Wastes. Physical/Chemical
     Methods.  Method 1311 Toxicity Characteristic
     Leaching Procedure. July 1992.
     http://www.epa.gov/epaoswer/hazwaste/test/pdfs/
     1311.pdf.
 3.23 U.S. EPA. SW-846 On-Line. Test Methods for
     Evaluating Solid Wastes. Physical/Chemical
     Methods.  Method 1310A Extraction Procedure
     (EP) Toxicity Test Method and Structural
     Integrity Test. July 1992.
     http://www.epa.gov/epaoswer/hazwaste/test/pdfs/
     1310a.pdf.
 3.24 California  Code of Regulations. Title 22 Section
     66261.126, Appendix II. Waste Extraction Test
     (WET) Procedures. August, 2002.
     http://ccr.oal.ca.gov/
 3.25 U.S. EPA.  Arsenic Treatment Technology Design
     Manual for Small Systems (100% Draft for Peer
     Review). June 2002. http://www.epa.gov/
     safewater/smallsys/
     arsenicdesignmanualpeerreviewdraft.pdf
 3.26 Cunningham, S. D. The Phytoremediation of Soils
     Contaminated with Organic Pollutants: Problems
     and Promise. International Phytoremediation
     Conference. May 8-10, Arlington, VA. 1996.
 3.27 Salt, D. E., M. et al. Phytoremedia-tion: A Novel
     Strategy for the Removal of Toxic Metals from
     the Environment Using Plants. Biotechnol.
     13:468-474.  1995.
3.28 Dushenkov, S., D. et al.. Removal of Uranium
     from Water Using Terrestrial Plants. Environ, Sci.
     Technol. 31(12):3468-3474.  1997.
3.29 Cunningham, S. D., and W. R. Berti, and J. W.
     Huang. Phytoremediation of Contaminated Soils.
     Trends Biotechnol. 13:393-397.  1995.
                                                 3-8

-------
                                                                   Table 3.1.
                                                 Applicability of Arsenic Treatment Technologies
Technology
Solidification/Stabilization
Vitrification
Soil Washing/Acid Extraction
Pyrometallurgical Treatment
In Situ Soil Flushing
Precipitation/Coprecipitation
Membrane Filtration
Adsorption
Ion Exchange
Permeable Reactive Barriers
Electrokinetics
Phytoremediation
Biological Treatment
Soil11
+
• +
+
+
+





+
+

Waste"
+
+

+






+


Water
Groundwater
and Surface
Water0





+
+
+
+
>
+
+
>
Brhiking Water





>•
+
>
>




Wastewaterd





-f






+
•^ = Indicates treatment has been conducted at full scale.

a    Soil includes soil, debris, sludge, sediments, and other solid phase environmental media.
b    Waste includes non-hazardous and hazardous solid waste generated by industry.
c    Groundwater and surface water also includes mine drainage.
d    Wastewater includes nonhazardous and hazardous industrial wastewater and leachate.
                                                                      3-9

-------
|
o
o'















TJ
2

O>
<
r*
•
9
0









^j i— t- cfl t*ซ CD O ^ OQ *~*^ ^ O ^ P O
||"!-8งltl sUls,
 < /-,
" M g. ^ B' " ere
"" o'
oo
gt
&.
I

*•- —
55
CT"
K"
P3
a.
o







*n
^

GO

O
•ง
"
"
"



S


s


• Redox potential
• Presence of organics
• Fine particulate
• Type of binder &
reagent
• Pretreatment
H
S
Sf
o
1

































!>!f^p>
il Iff 7*1

*~j *• • !__( b^ \S li.
d * p;- o" o
"S ^ S- -r*
p5~ o> "* •

pa pr* ^^

o ง ฐ
•1 S ^
05 ,
fD O
O ^3
8 |
" o'
g p
O H -
r T ป
> ป 0
ซ 1 i
p *? m
OQ -• M
ft












Development Status
Treatment Train
(excludes off-gas treatment)


Residuals Produced
O&M or Capital Intensive
Availability
System Reliability/Maintainability
Overall Cost
High Arsenic Concentration



Arsenic Chemical Form


pH

O
n>
O
p
o
ro
ง-'
I
?
?
o o
ซ• 5"
1 2
P j^
* 3.
> a
B5"
ro ,
[hat May Require
ct Performance or Cost
 I.
 S"
 H
 3
 ง
 =>• 2
 g  re
 2. 01
 I
 CA
  ?

trq

-------
t/3
O
i •
hcj
S-
1'


















*
*

t-1

I
•
@
ฉ
S

s




tfQ o* P3
ฐ* -
>-tf
Q
3
1
o
EL

m
o
^S

5'
OQ









*
2

< J73
^
O O
Rf>^
s&
o
a
>






S' ^ H i?1 '"d
1 a i* 1 a
@. 8 8 s ฃ
•3-. o P % CO
ft ft ^ CD 00
"ฐMS'
ii

S.
•a.
iw
g.
i?

o
Q
;s








^
.^
1
;O1
;r
I"*1
•
ฉ
ฉ




S

O. C/D H ^ ฐ ^ W
ง: ^ T3 ft g" ^ tf
g S3 o c 3 pL o
ft &. fฐ ft 3' ** 3
O o g' o p O
N' g 2.
<"> S- >ง
i

•S S|p^^H< i^
S> ' G* ^ (^2 *rrj .j ^
2 1^ 3. ' o ^ ^
O O o g-' t"1 i "^ S
r^ 2! ^" O* O
" ' )iJ ซ-f •
M ii ti.
g. Q ^B*
o ft-"  ป n
g 1. i
p 11 n>
OQ -• 
 ts
 re
 IH
 o   is
era   cr
 n>
 re

 3.
 I
S
a
8


-------
1
s
D
g4
CD
1
s.
o
ป











^
Ki

(-1

rง
•
e
c>
s

s

s


• • • * •



%
o

*I^J
1
Hซ
8
T3
ฃ3"
o'
o







hd
K!

00

r*
•
•
ฎ


s

s


	
vฑ H O g^ H g ^
tlP;lli
ซ' & ;r & &• o
173 (TQ 8* fป " "5
1 i 1 i. &
& "8 S q


*g SS 0 ซป -id Ki [V
h4^ ' S. *T3 rf. )—t . \s

|^i i-^ s? — ^^ pฃj PJ rp i
fP ^ 8 Hi. i HH ' S
>T3 ' tf "

rf K,* ^4
g_ ^ p*
ง *•"*•<
t3 C^ i^
o ^R
•t <• •
1 i
S- ^
8 ง
to ef.
^^ o
OH-

3
1 1 0Q
ฃ S? o
1 s a
1 ซ 8
?D













Development Status
Treatment Train
(excludes off-gas treatment)


Residuals Produced
O&M or Capital Intensive
Availability
System Reliability/Maintainability
Overall Cost

High Arsenic Concentration

Arsenic Chemical Form

pH

O
ฃ
re
i
en

S

hi
S
3- i"
ro (a
- S-
>- a
>^) n
re* "%
Hri ta
t May Require
'erformance or C
o
a
E.
ra'

H
 o
 a
 O
 sr

 I.
 o
era
 n

 3
 o

 a-
 o

 n-.

 c

-------
                       Table 3.2
Arsenic Treatment Technologies Screening Matrix (continued)



































Rating Codes
• -Better;

QU -Average;
^— ^ - Worse;
Y-Yes;N-No.
F - Full; P - Pilot.
S - Solid; L - Liquid; V - Vapor.
Cap - Capital; N - Neither; O&M - Operation &
Maintenance.

/ - May require pretreatment or affect cost and
performance.
Adsorption





Ion Exchange







Permeable Reactive Barriers














a
1
S


1
0
F ...





F







F












c-
a
|

~ S
H ss
a ฐ
a 
13
la
|
-<

•
























ฃ
ซ
c
S
'ซ
•S*
"3
1
C3
1
K
S
St

9




(f*\
Cy)























+-
W
u
1
6

ฎ a




a
w







ฉ








Characteristics That May Require
Pretreatment or Affect Performance or Cost

B
1
C
o
e
o
U
u
1
S
•a
m
j





/

















s
h
O
'a
1
JS
U
1
J





/







/















9,
j





/























Other Characteristics
.?- Flow rate .
• pH
• Fouling
• Contamination
concentration
• Spent media
• Presence of
competing ions
• Presence of organics
• Presence of trivalent
ion
• Project scale
• Bed regeneration
• Sulfate
• Fractured rock
• Deep aquifers &
contaminant plumes
• High aquifer
hydraulic
conductivity
• Stratigraphy
• Barrier plugging
• PRB depth
                        3-13

-------
cr JL
o  M
   1
   •3'
    o
    I
   p

   k
    ง
    ง


    I

    cT
    B
   •B
    ts
    o
    I
    s
    CD
    i
    en
    ft.
    o
00
Q
ง
3
re
ฃ
1
2.
I
&•
n>
:D
1
n>
3
1

^
o
H
8
i*
o
0
S.
CD'
tn
f?

1
o-
CD
O
r

o
^
tiO
creenins
uw
a.
3.
X
&•
|
1"
|
•
3^
1

C^
o
1
i
1
OJ
Lo



'-d
|
O
H*
'emediation















v


2


r
GO

^


0
0


_
B
s



s

s

• Contaminant d
• Climatic or set
conditions
" &

>-^
w
CD*
^
CD
ST.
O
t/1















>n


*:


01
tr1

O
1?
•^
o
p>


l\
^
s



s

s

e • • • •
CD ("} OO O ^ GO CD GO

& <^
a.
CD
S?.
o'
Q
OQ
1
1
I














>TJ


^


JjO
r

0 RP 0
s w
^
>
t>


ฃ*•!
U
S



S

s

ฃ3 *~d H^ ^>- o f*\ t^
f~> 5 fB -^ S o o
^ ง- 3 5 ^3 P
P^" CD *T3 &* fp po O
| | ง s & 1. 8
[^ P R- CD P P ฃ?
g CD d „ St. g ง
5? & CD c 2 3. 3-
3" i.
CD' g"-
1 ง

*a %gncซhrji-< is.
g, . |.-ง ^ ^ ' P"
H [S, ^~ O, ^, ft |
/T\ • ^
CJ • ง.
| | *M
! I I
ง !z! ^- o^ p ซ
3 s;^:
S 3^ "^
3" CD '
s "6^
3 1 ฐ
S3 O
O ปT3
8 1
w ff.
ซ-*• o
g a
a. SP


















Development Status
Treatment Train
(excludes off-gas treatment)




Residuals Produced
O&M or Capital Intensive
Availability
System Reliability/Maintainability



Overall Cost

High Arsenic Concentration


Arsenic Chemical Form


PH
O
i
o
n
c?

a
ฃ




>4
a
?
re O
ca -T-
a ป
i s
B <5_
o n.
>!
rhat May Requin
rt Performance 01
— s TO
g>
f-t-
                                                                                                                                        I.
                                                                                                                                        B"

                                                                                                                                        H
                                                                                                                                        S
                                                                                                                                        B

                                                                                                                                        a H
                                                                                                                                        O  83
                                                                                                                                       "B. 2
                                                                                                                                        I
                                                                                                                                        o
re
a-

-------
             Table 3.3
Available Arsenic Treatment Cost Data
Site
Amount
Treated
Capita!
Cost
Annual
O&M
Cost
Unit Cost
Total Cost
Cost Explanation
Source
Solidification/Stabilization

Electrical Substation in Florida

3,300 cubic
yards

• -

-
$60 - $290 per
ton
$85 per cubic
yard
"
-
• Cost is for S/S of metals and is not
arsenic-specific
• Cost year not specified
• Excludes Disposal Costs
• Costs in 1995 Dollars
3.5
3.6, 3.7
Vitrification
Parsons Chemical Superfund Site
3,000 cubic
yards
$350,000
$550,000

$375 - $425
per ton

• Capital cost includes pilot testing,
mobilization, and demobilization
• Unit cots are for operation of
vitrification equipment only
• Cost year nor specified
3.8
Soil Washing/Acid Extraction
King of Prussia Superfund Site
-
-
-
-
12,800 cubic
yards
-
-
400 cubic
yards
38,000 tons
-
-
-
-
-
-
-
-
-
-
$400 per ton
$100 - $300
per ton
$65 per ton
$80 per ton
$203 per ton
-
-
-
-
$7.7 million
• Cost year not specified
• Cost year not specified
• Cost year not specified
• Cost year not specified
• Cost year not specified
3.9,
3.10
3.10
3.11
3.11
3.12
Pyrometallurgical Recovery
-
-
-
-
$208 to $458
per ton
-
• Cost is not arsenic-specific
• Costs in 1991 dollars
3.10
In Situ Soil Flushing - No cost data identified
Precipitation/Coprecipitation
Vineland Chemical Company
Winthrop Landfill
Energized Substation in Florida
1,400 gpm
65 gpm
44 million
gallons
-
$2
million
-
$4 million
$250,000
-
-
-
$0.0006 per
gallon
-
-
-
• Cost year not specified
• Cost year not specified
• Cost year not specified
3.13
3.14
3.15
Membrane Filtration - No cost data identified
              3-15

-------
                                                               Table 3.3
                                            Available Arsenic Treatment Cost Data (Continued)
Site
Amount
Treated
Capital
Cost
Annual
O&M
Cost
Unit Cost
Total Cost
Cost Explanation
Source
Adsorption
"
"
"
"
$0.003 - $0.76
per 1,000
gallons

• Cost year not specified
3.16
Ion Exchange
-
-
$9,000
-
-
-
• Cost year not specified
3.17
Permeable Reactive Barrier
Monticello Mill Tailings
-
$1.2
million
-
-
-
• Cost year not specified
3.18
Electrokinetics
Pederok Plant, Kwint, Loppersum,
Netherlands
Blackwater River State Forest, FL
325 cubic
yards
-
-
-
-
-
$70 per ton
$883 per ton
-
-
• Cost year not specified
• Cost year not specified
3.11
3.21
PhytoremediatioH
~
"
"
-
12 acres
1 acre, 20
inches deep
"
-
~
"
"
~"
"*
"
"
~
"
'
$2 - $6 per
1,000 gallons
$0.02 - $.76
per cubic yard
$200,000
$60,000 -
$100,000

"
• 1998 dollars
• Cost is for phytoextraction of lead from
soil
• Cost year not specified
• Cost is for phytoextraction from soil
• Contaminant was not specified
• Cost is for ex situ treatment of water
containing radionuclides
• Cost year not specified
• Cost year not specified
• Cost is for phytostabilization of metals,
and is not arsenic-specific
3.26
3.27
3.28
3.29
Biological Treatment
-
-
-
-
-
-
-
-
$0.50 per
1,000 gallons
$2 per 1,000
gallons
-
-
• Cost year not specified
• Cost year not specified
3.19
3.20
- = Data nor provided
gpm - gallons per minute
                                                                 3-16

-------
                                                                   Table 3.4
                                        Summary of Cost" Data for Treatment of Arsenic in Drinking Water
Technology
Precipitation/Coprecipitation
(coagulation-assisted
microfiltration)
Adsorption (greensand filtration)
Adsorption (activated alumina,
influent pH 7 -8)
Jon exchange (anion exchange,
influent <20 mg/L sulfate)
Design Flow Rate
0.01 mgd
Capital Cost ($)
142,000
12,400
15,400
23,000
Annual O&M
Cost($)
22,200
7,980
6,010
- - -5,770
0.1 mgd
Capital Cost ($)
463,000
85,300
52,200
54,000
Annual O&M
Cost($)
35,000
13,300
23,000
12,100
1 mgd
Capital Cost ($)
2,010,000
588,000
430,000
	 350,000 - -
Annual O&M
Cost ($)
64,300
66,300
201,000
-v 52,200 -
Source: Derived from Ref. 3.4

a.  Costs are rounded to three significant figures and are in September 1998 dollars. Costs do not include pretreatment or management of treatment residuals.
   Costs for enhanced coagulation/filtration and enhanced lime softening are not presented because the costs curves for these technologies are for modification of
   existing drinking water treatment systems only (Ref. 3.4), and are not comparable to other costs presented in this table, which are for new treatment systems.
mgd = million gallons per day
O&M = operating and maintenance
mg/L = milligrams per liter
< = less than
                                                                     3-17

-------

-------
                     II
ARSENIC TREATMENT TECHNOLOGY SUMMARIES

-------

-------
               IIA
ARSENIC TREATMENT TECHNOLOGIES
  APPLICABLE TO SOIL AND WASTE

-------

-------
4.0     SOLIDIFICATION AND
        STABILIZATION TREATMENT FOR
        ARSENIC
                               Model of a Solidification/Stabilization System
  Summary

  Solidification and stabilization (S/S) is an      '•
  established treatment technology often used to
  reduce the mobility of arsenic in soil and waste. The
  most frequently used binders for S/S of arsenic are
  pozzolanic materials such as cement and lime. S/S
  can generally produce a stabilized product that
  meets the regulatory threshold of 5 mg/L leachable
  arsenic as measured by the TCLP. However,
  leachability tests may not always be accurate
  indicators of arsenic leachability for some wastes
  under certain disposal conditions.
Technology Description and Principles
                                             i

The stabilization process involves mixing a soil or;
waste with binders such as Portland cement, lime, fly
ash, cement kiln dust, or polymers to create a slurry,
paste, or other semi-liquid state, which is allowed time
to cure into a solid form. When free liquids are present
the S/S process may involve a pretreatment step   :
(solidification) in which the waste is encapsulated or
absorbed, forming a solid material. Pozzolanic bidders
such as cement and fly ash are used most frequently for
the S/S of arsenic. No site-specific information is ;
currently available on the use of organic binders to
immobilize arsenic.                            ;
  Technology Description: S/S reduces the mobility
  of hazardous substances and contaminants in the
  environment through both physical and chemical
  means. It physically binds or encloses contaminants
  within a stabilized mass and chemically reduces the
  hazard potential of a waste by converting the
  contaminants into less soluble, mobile, or toxic ;
  forms.                                      ;
  Media Treated:

    •  Soil
    •  Sludge
Other solids
Industrial waste
  Binders and Reagents used in S/S of Arsenic: ,
       Cement
       Fly Ash
       Lime
       Phosphate
pH adjustment agents
Sulfur
                                          Dry
                                        Reagents
                           Water
                       (If Required) I
                                Liquid
                               Reagents
                                             Stabilized Waste
                            The process also may include the addition of pH
                            adjustment agents, phosphates, or sulfur reagents to
                            reduce the setting or curing time, increase the
                            compressive strength, or reduce the leachability of
                            contaminants (Ref. 4.8). Information gathered for this
                            report included 45 Superfund remedial action projects
                            treating soil or waste containing arsenic using S/S.
                            Figure 4.1 shows the frequency of use of binders and
                            reagents in 21 of those S/S treatments. The figure
                            includes some projects where no performance data were
                            available but information was available on the types of
                            binders and reagents used.  Some projects used more
                            than one binder or reagent. Data were not available for
                            all 46 projects.

                                                Figure 4.1
                                      Binders  and Reagents Used for
                                Solidification/Stabilization of Arsenic for 21
                               Identified Superfund Remedial Action Projects
                                  13
                                                     n       2
                                                     M      FTI
                                                     KiJ      Ni
Cement  Phosphate   pH     Lime
                  Adjustment
                   Agents
                                                                                                 Sulfur
                                                   4-1

-------
S/S often involves the use of additives or pretreatment
to convert arsenic and arsenic compounds into more
stable and less soluble forms, including pH adjustment
agents, ferric sulfate, persulfates, and other proprietary
reagents (Ref. 4.3,4.8).  Prior to S/S, the soil or waste
may be pretreated with chemical oxidation to render the
arsenic less soluble by converting it to its As(V) state
(Ref. 4.3).  Pretreatment with incineration to convert
arsenic into ferric arsenate has also been studied, but
limited data are available on this process (Ref. 4.3).

This technology has also been used to immobilize
arsenic in soil in situ by injecting solutions of chemical
precipitants, pH adjustment agents, and chemical
oxidants. In this report, such applications are referred
to as in situ S/S. In one full-scale treatment, a solution
of ferrous iron, limestone, and potassium permanganate
was injected (Ref. 4.8). In another full-scale treatment,
a solution of unspecified pH adjustment agents and
phosphates was injected (Ref. 4.10).

Media and Contaminants Treated

S/S is used frequently to immobilize metals  and
inorganics in soil and waste. It has been used to
immobilize arsenic in environmental media  such as soil
and industrial wastes such as sludges and mine tailings.

Type, Number, and Scale of Identified Projects
Treating Soil and Wastes Containing Arsenic

S/S of soil and waste containing arsenic is
commercially available at full scale.  Data sources used
for this report included information about 58 full-scale
and 19 pilot-scale applications of S/S to treat arsenic.
This included 45 projects at 41 Superfund sites (Ref.
4.8). Figure 4.2 shows the number of applications at
both full and pilot scale.

                     Figure 4.2
    Scale of Identified Solidification/Stabilization
           Projects for Arsenic Treatment
Full
  Factors Affecting S/S Performance

  •    Valence state - The specific arsenic compound
      or valence state of arsenic may affect the
      leachability of the treated material because
      these factors affect the solubility of arsenic.
      pH and redox potential - The pH and redox
      potential of the waste and waste disposal
      environment may affect the leachability of the
      treated material because these factors affect the
      solubility of arsenic and may cause arsenic to
      react to form more soluble compounds or reach
      a more soluble valence state.
      Presence of organics - The presence of volatile
      or semivolatile organic compounds, oil and
      grease, phenols, or other organic contaminants
      may reduce the unconfined compressive
      strength or durability of the S/S product, or
      weaken the bonds between the waste particles
      and the binder.
      Waste characteristics - The presence of
      halides, cyanide, sulfate, calcium, or soluble
      salts of manganese, tin, zinc, copper, or lead
      may reduce the unconfined compressive
      strength or durability of the S/S product, or
      weaken the bonds between the waste particles
      and the binder.
  •    Fine particulate - The presence of fine
      particulate matter coats the waste particles and
      weakens the bond between the waste and the
      binder.
  •    Mixing - Thorough mixing is necessary to
      ensure waste particles are coated with the
      binder.
Summary of Performance Data

Table 4.1 provides performance data for 10 pilot-scale
treatability studies and 34 full-scale remediation
projects. Due to the large number of projects, Table 4.1
lists only those for which leachable arsenic
concentrations are available for the treated soil or
waste, with the exception of projects involving only in
situ stabilization. In situ projects without information
on the leachability of arsenic in the stabilized mass are
included in the table because this type of application is
more innovative and information is available for only a
few applications.

The performance of S/S treatment  is usually measured
by leach testing a sample of the stabilized mass.  For
most land-disposed arsenic-bearing hazardous wastes
that fall under RCRA (including both listed and
                                                    4-2

-------
characteristic wastes), the treatment standard is less
than 5.0 mg/L arsenic in the extract generated by ti>e
toxicity characteristic leaching procedure (TCLP). | The
standard for spent potliners from primary aluminum
smelting (K088) is 26.1 mg/kg total arsenic (Ref. 4.10).
For listed hazardous wastes, the waste must be disposed
in a Subtitle C land disposal unit after treatment to ;meet
the standard for arsenic and any other applicable
standards, unless it is specifically delisted.  For
hazardous wastes exhibiting the characteristic for ;
arsenic, the waste may be disposed in a Subtitle D :
landfill after being treated to remove the  characteristic
and to meet all other applicable standards.        >

Of the 23  soil projects identified for this report, 22 j
achieved a leachable arsenic concentration of less than
5.0 mg/L in the stabilized material. Of the 19 industrial
waste projects, 17 achieved a leachable arsenic    ;
concentration of less than 5.0 mg/L in the stabilized
material.  Leachability data are not available for the
projects that involve only in situ stabilization.    :

Four projects (Projects 25,26, 27, and 41, Table 4.1)
included pretreatment to oxidize As(III) to As(V). lln
these projects, the teachability of arsenic in industrial
wastes was reduced to less than 0.50 mg/L. The  I
compound treated in Projects 24, 25, and 26 was  ;
identified as arsenous trisulfide. All three treatment
processes  involved pretreating a waste containing 5,000
to 40,000  mg/kg arsenous trisulfide with  chemical;
oxidation  (Ref. 4.1). The specific arsenic compound in
another S/S treatment (Project 41) was identified as
As2O3.  This treatment process included pretreatmept by
chemical oxidation to form ferric arsenate sludge j
followed by S/S with lime (Ref. 4.3).             i

Limited data are available about the long-term stability
of soil and waste containing arsenic treated using S/S.
Projects 12, 13, and 16 were part of one study that ]
tested the  teachability of arsenic six years after S/S! was
performed (see Case Study: Long-Term Stability of S/S
or Arsenic).                                   <

The case study on Whitmoyer Laboratories SuperfUnd
Site discusses in greater detail the treatment of arsehic
using S/S. This information is summarized in Tablฃ
4.1, Project 20.                                •

Applicability, Advantages, and Potential Limitations

The mobility of arsenic depends upon its  valence state,
the reduction-oxidation potential of the waste disposal
environment, and the specific arsenic  compound  !
contained  in the waste (Ref. 4.1). This mobility is ;
usually measured by testing the teachability of arsefaic
under acidic conditions. In some disposal environments
the leachability of arsenic may be different than that
  Case Study:  Long-Term Stability of S/S of
  Arsenic

  EPA obtained leachate data from landfills accepting
  wastes treated using solidification/stabilization
  operated by Waste Management, Inc., Envirosafe,
  and Reynolds Metals.  The Waste Management, Inc.
  landfills received predominantly hazardous wastes
  from a variety of sources, the Envirosafe landfill
  received primarily waste bearing RCRA waste code
  K061 (emission control dust and sludge from the
  primary production of steel in electric furnaces) and
  the Reynolds Metals facility was a monofill
  accepting waste bearing RCRA waste code K088
  (spent potliners from primary aluminum reduction).
  Analysis of the leachate from 80 landfill cells
  showed 9 cells, or 11%, had dissolved arsenic
  concentrations higher than the TCLP level of 5.0
  mg/L.  The maximum dissolved arsenic
  concentration observed in landfill leachate was 120
  mg/L.  Analysis of the leachate from 152 landfill
  cells showed 29 cells, or 19%, had total arsenic
  concentrations in excess of the TCLP level of 5.0
  mg/L.  The maximum total arsenic concentration
  observed in landfill leachate was 1,610 mg/L (Ref.
  4.12).

  Another study reported the long-term stability of S/S
  technologies treating wastes from three landfills
  contaminated with heavy metals, including arsenic
  (Ref. 4.16). S/S was performed at each site using
  cement and a variety of chemical additives. TCLP
  testing  showed arsenic concentrations ranging from
  zero to 0.017 mg/L after a 28-day cure time.  Six
  years later, TCLP testing showed leachable arsenic
  concentrations that were slightly higher than those
  for a 28-day cure time (0.005 - 0.022 mg/L),  but the
  levels remained below 0.5 mg/L. However, the
  stabilized waste was stored above ground, and
  therefore may not be representative of waste
  disposed in a landfill (see Projects 12, 13, and 16 in
  Table 4. land Table 4.2).
predicted by an acidic leach test, particularly when the
specific form of arsenic in the waste shows increased
solubility at higher pH and the waste disposal
environment has a high pH. Analytical data for
leachate from monofills containing wastes bearing
RCRA waste code K088 (spent aluminum potliners)
indicate that arsenic may leach from wastes at levels
                                                   4-3

-------
 Case Study: Whitmoyer Laboratories
 Superfund Site

 The Whitmoyer Laboratories Superfund Site was a
 former veterinary feed additives and phannaceuticals
 manufacturing facility. It is located on
 approximately 22 acres of land in Jackson Township,
 Lebanon County, Pennsylvania.  Production began at
 the site in 1934. In the mid-1950's the facility began
 using arsenic in the production of feed additives.
 Soils on most of the area covered by the facility are
 contaminated with organic arsenic.

 Off-site stabilization began hi mid-1999 and was
 completed by the spring of 2000. A total of 400 tons
 of soil were stabilized using a mixture of 10% water,
 10% ferric sulfate, and 5% Portland cement.  The
 concentration of leachabile arsenic hi the treated soil
 was below 5.0 mg/L, as measured by the TCLP.
 Information on the pretreatment arsenic leachability
 was not available.
higher than those predicted by the TCLP (see Case
Study: Long-term Stability of S/S of Arsenic).

Some S/S processes involve pretreatment of the waste
to render arsenic less soluble prior to stabilization (Ref.
4.1,4.3). Such processes may render the waste less
mobile under a variety of disposal conditions (See
Projects 25,26,27,and 41 in Table 4.1), but also may
result in significantly higher waste management costs
for the additional treatment steps.

In situ S/S processes may reduce the mobility of arsenic
by changing it to less soluble forms, but do not remove
the arsenic.  Ensuring thorough mixing of the binder
and the waste can also be challenging for in situ S/S
processes, particularly when the subsurface contains
large particle size soil and debris or subsurface
obstructions. The long-term effectiveness of this type
of treatment may be impacted if soil conditions cause
the stabilized arsenic to change to more soluble and
therefore more mobile forms.

Summary of Cost Data

The reported costs of treatment of soil containing
metals using S/S range from $60 to $290 per ton (Ref.
4.5, cost year not identified).  Limited site-specific cost
data are currently available for S/S treatment of arsenic.
At two sites, (Projects  21 and 22), total project costs, in
1995 dollars, were about $85 per cubic yard, excluding
disposal costs (Ref. 4.21).
 Factors Affecting S/S Costs

     Type of binder and reagent - The use of
     proprietary binders or reagents may be more
     expensive than the use of non-proprietary
     binders (Ref. 4.16).
 •   Pretreatment - The need to pretreat soil and
     waste prior to S/S may increase management
     costs (Ref. 4.18).
     Factors affecting S/S performance - Items in
     the "Factors Affecting S/S Performance" box
     will  also affect costs.
References

4.1.   U.S. EPA. Arsenic & Mercury - Workshop on
      Removal, Recovery, Treatment, and Disposal.
      Office of Research and Development. EPA-600-
      R-92-105. August 1992.
      http://epa.gov/ncepihom.
4.2.   U.S. EPA. Contaminants and Remedial Options
      at Selected Metal-Contaminated Sites. Office of
      Research and Development. EPA-540-R-95-
      512. July 1995. http://epa.gov/ncepihom.
4.3.   U.S. EPA. Final Best Demonstrated Available
      Technology (BOAT) Background Document for
      K031, K084, K101, K102, Characteristic Arsenic
      Wastes (D004), Characteristic Selenium Wastes
      (DO 10), and P and U Wastes Containing Arsenic
      and Selenium Listing Constituents. Office of
      Solid  Waste. May 1990.
4.4.   U.S. EPA National Risk Management Research
      Laboratory. Treatability Database. March 2001.
4.5.   U.S. EPA Office of Research and Development.
      Engineering Bulletin, Technology Alternatives
      for the Remediation of Soils Contaminated with
      Arsenic, Cadmium, Chromium, Mercury, and
      Lead. Cincinnati, OH.  March 1997.
      http://www.epa.gov/ncepi/Catalog/
      EPA540S97500.html
4.6.   TIO.  Database for EPA REACH IT
      (Remediation And Characterization Innovative
      Technologies). March 2001.
      http://www.epareachit.org.
4.7.   U.S. EPA. Solidification/Stabilization Use at
      Superfund Sites. Office of Solid Waste and
      Emergency Response.  EPA 542-R-00-010.
      September 2000.  http://clu-in.org.
4.8.   U.S. EPA. Treatment Technologies for Site
      Cleanup: Annual Status Report (Tenth Edition).
      Office of Solid Waste and Emergency Response.
      EPA-542-R-01-004. February 2001. http://clu-
      in.org.
                                                   4-4

-------
 4.9.   U.S. EPA. Treatment Technology Performance
       and Cost Data for Remediation of Wood   '
       Preserving Sites.  Office of Research and  '
       Development. EPA-625-R-97-009. Octobe;r
       1997.  http://epa.gov/ncepihom.          ]
 4.10.  Code of Federal Regulations, Part 40, Section
       268. http://lula.law.cornell.edu/cfr/       '
       cfr.php?title=40&rype=part&value=268   !
. 4.11.  Personal communication with Jim Sook,   ;
       Chemical Waste Management, Inc. March 2001.
 4.12.  Federal Register.  Land Disposal Restriction's:
       Advanced Notice of Proposed Rulemaking.':
       Volume 65, Number 118. June 19,2000. pjp.
       37944 - 37946.                         ;
       http://www.epa.gOv/fedrgstr/EPA-WASTE/i
       2000/June/Day-19/fl 5392.htm            ;
 4.13.  U.S. EPA. Biennial Reporting System. Draft
       Analysis. 1997.                         :
 4.14.  Fuessle, R.W. andM.A. Taylor. Stabilization of
       Arsenic- and Barium-Rich Glass Manufacturing
       Waste. Journal of Environmental Engineering,
       March 2000.  pp. 272-278.              !
       http://www.pubs.asce.org/journals/ee.html !
 4.15.  Wickramanayake, Godage, Wendy Condit, 4nd
       Kim Cizerle.  Treatment Options for Arsenic
       Wastes.  Presented at the U.S. EPA Workshop on
       Managing Arsenic Risks to the Environment:
       Characterization of Waste, Chemistry, and i
       Treatment and Disposal. Denver, CO. May! 1 -
       3,2001.                                |
 4.16.  Klich,  Ingrid. Permanence of Metals      I
       Containment in Solidified and Stabilized Wastes.
       A Dissertation submitted to the Office of   i
       Graduate Studies of Texas A&M University !in
       partial fulfillment of the requirements for the
       degree of Doctor of Philosophy. December ;
       1997.
 4.17.  Klean Earth Environmental Company. Spring
       Hill Mine Study. August 2001.            ;
       http://www.keeco.com/spring.htm.
 4.18.  Markey, R. Comparison and Economic Analysis
       of Arsenic Remediation Methods Used in Soil
       and Groundwater. M.S. Thesis. FAMU-FSU
       College of Engineering. 2000.            j
4.19.  Bates, Edward, Endalkachew Sable-Demessie,
       and Douglas W. Grosse. Solidification/     i
       Stabilization for Remediation of Wood     j
       Preserving Sites: Treatment for Dioxins, PCp,
       Creosote, and Metals. Remediation. John Wiley
       & Sons, Inc. Summer 2000. pp. 51 - 65.   j
       http://www.wiley.com/cda/product/       i
       0,,REM,OO.html                         '
4.20.   Palfy, P., E. Vircikova, and L. Molnar.     ;
       Processing of Arsenic Waste by Precipitation and
       Solidification. Waste Management. Volume  19.
       1999. pp. 55 - 59.                       \
       http://sdnp.deUii.nic.in/node/jnu/database/  ;
      biogeoch/bioch99.html
4.21  Redwine JC. Successful In Situ Remediation
      Case Histories: Soil Flushing And
      Solidification/Stabilization With Portland
      Cement And Chemical Additives.  Southern
      Company Services, Inc. Presented at the Air and
      Waste Management Association's 93rd Annual
      Conference and Exhibition, Salt Lake City, June
      2000.
4.22  Miller JP. In-Situ Solidification/Stabilization of
      Arsenic Contaminated Soils. Electric Power
      Research Institute.  Report TR-106700. Palo
      Alto, CA. November 1996.
4.23  E-mail from Bhupi Khona, U.S. EPA Region 3 to
      Sankalpa Nagaraja, Tetra Tech EM, Inc.,
      regarding S/S of Arsenic at the Whitmoyer
      Laboratories Superfund site. May 3, 2002.
                                                  4-5

-------
                           Table 4.1
Solidification/Stabilization Treatment Performance Data for Arsenic
Project
Number
s p= „_;_ _ _ _ =i-i_ _==i . _^
..'.-'. i: _ _ f ::-: -sf I --:}
Industry and Site
Type !
;: - ^
Ji — , .
ai= . -i i
Waste or Media
^ f ~~f
ii
i ป
3-
:H
Scale"
t . - -
Site Name, Location,
and Project
Completion Date"
JMfial Arsenic
Concentration
(mg/kg) or
Leachability
(mg/L) (Test
method)
UnaJ Arsenic.
Concentration
(mg/kg) or
Leachability (mg/L)
(Test method)
• • ' • T1ff---^-f,T- TTTf
^^ ซWN> * ; i • *•'
= ! = a : .1 1 A
- VI I Hi
-.---.- 1 '- •• ,
Binderior ; S
Stabilization^Process
'-• !'•
mi • ".!!
Source
Environmental Media
1
2
3
4
5
6
7
8
9
Disposal Pit
Fire/Crash Training
Area;
Federal Facility
Metal Ore Mining and
Smelting
Munitions
Manufacturing/
Storage
—
—
-
-
-
20,000 cy sludge
and soil
3,000 cy sludge
and soil
500,000 cy soil
1, 000 cy soil
Soil
Soil
Soil
Soil
Soil
Full
Full
Full
Full
Full
Full
Full
Full
Full
Pab Oil Superfund
Site, LA
August 1998
Jacksonville Naval
Air Station Superfund
Site, FL
October 1995
Anaconda Co.
Smelter Superfund
Site, MT
January 1994
Fernald
Environmental
Management Project
Superfund Site, OH
September 1999
—
—
-
-
-
7.5-25.1mg/kg
NDC- 61 mg/kg
50 - 100 mg/L
(EPT)
3 - 18 mg/kg
0.18 mg/L (EPT)
0.19 mg/L (TCLP)
0.0086 mg/L
(EPT)
0.0091 mg/L
(TCLP)
0.017 mg/L
(TCLP)
O.I mg/L (TCLP)
<5 mg/L (TCLP)
<2 mg/L (TCLP)
<5mg/L (TCLP)
0.028 mg/L (EPT)
0.017 mg/L (TCLP)
0.0049 mg/L (EPT)
O.002 mg/L (TCLP)
0.0035 mg/L (TCLP)
Cement, organophilic
clay, other unspecified
organic, ferric sulfate,
other unspecified
inorganic, and sulfur
Cement, lime, other
unspecified inorganic,
and kiln dust
Unspecified inorganic
Cement and
other unspecified
inorganic
Cement
Cement
Proprietary binder
Proprietary binder
Proprietary binder
4.8
4.8
4.8
4.8
4.4
4.4
4.4
4.4
4.4
                              4-6

-------
                                 Table 4.1
Solidification/Stabilization Treatment Performance Data for Arsenic (continued)
Project
Number
10
11
12
13
14
15
16
17
Industry and Site
Type
—
-
Oil Processing &
Reclamation
Oil Processing &
Reclamation
Pesticides
Pharmaceutical
Transformer and
Metal Salvage
Wood Preserving
: ' 1 •' ! ' 5 1 :
i
r
i
Waste or Media
Soil
Soil
Filter cake and
oily sludge
Soil
Soil
3,800 tons sludge
and soil
Soil
14,800 cy soil
Scale"
Full
Full
Full
Full
Full
Full
Full
Full
Site 'Name, Location,
and Project
Completion Dateb
-
-
Imperial Oil Co -
Champion Chemical
Co Superfund Site,
NJ
Imperial Oil Co -
Champion Chemical
Co Superfund Site,
NJ
-
"
Portable Equipment
Salvage Co, OR
Macgillis And
Gibbs/Bell Lumber
And Pole Superfund
Site, MN
February 1998
Initial Arsenic
Concentration
(mg/kg) or
Leachability
(mg/L) (Test
method)
2,430 mg/kg
0.10 mg/L (TCLP)
40 mg/kg
92 mg/kg
0.60 mg/L (EPT)
28.0 mg/L (WET)
260,000 mg/kg
4,3 10 -4,390 mg/L
(TCLP)
42 mg/kg
1 - 672 mg/kg
Final Arsenic
Concentration
(mg/kg) or
Leachability (mg/L)
(Test method)
0.1 1-0.26 mg/L
(TCLP)
0.04 mg/L (TCLP)
NDc'd (TCLP)
0.017" mg/L (TCLP)
0.27 mg/L (EPT)
6.5 mg/L (WET)
1.24 -3. 44 mg/L
(TCLP)
0.004d mg/L (TCLP)
55 mg/L (TCLP)
Binder or
Stabilization Process
fly ash, cement, and
proprietary reagent
„
Cement and proprietary
additives
Cement and proprietary
additives
-
Potassium persulfate,
ferric sulfate, and
cement
Proprietary binder
Cement
Source
4.3
4.1
4.16
4.16
4.1
4.15
4.16
4.8
                                   4-7

-------
                                Table 4.1
Solidification/Stabilization Treatment Performance Data for Arsenic (continued)
Project
Number
18
19
20
21
22
23
- ---- -I"- =s= 1 -= 	 3^ -,= -== -5- ^==3 =
	 	 ^S -11--= ^-A-^J=X,---Pฐ : alL
':t 14ป " -E S, II
• : ",-;- , ~J - - -,-- "-: +
Industry and Site :
Type
Wood Preserving
Wood Preserving
Veterinary feed
additives and
pharmaceutical
manufacturing
Electrical substation
Electrical substation
Wood Preserving
-..._*.. ^ •'ซ-
i
i
7 1 H
Waste or Media
Soil
13,000 cy soil
400 tons
1 ,000 cy soil
3,300 cy soil
Soil
i
i =
Scale"
Full
Full
Full
Pilot
Pilot
Pilot
Site Name, Location,
and Project
Completion Dateb

Palmetto Wood
Preserving Superfund
Site, SC
1989
Whitmoyer
Laboratories
Superfund Site
Florida
1995
Florida
1995
Selma Pressure
Treating Superfund
Site, Selma, CA
1998
Initial Arsenic n
Concentration^
(mg/kg)or
Leachability
(mg/L) (Test
method)
91 - 128 mg/kg
6,200 mg/kg

<0.5 -2,000 mg/kg
1.42 -3. 7 mg/L
(TCLP)
O.5 - 1,900 mg/kg
0.15 - 3.5 mg/L
(TCLP)
10 mg/L (TCLP)
(L i • : .
: JJFinal ATSenic,a|
Concentration
(mg/kg) or J
Leachability (mg/L)
(Test method)
0.015 - 0.29 mg/L
0.02 mg/L (TCLP)
< 5 mg/L (TCLP)
ND- 0.11 (TCLP)
0.22 - 0.38 (TCLP)
< 0.1 mg/L (TCLP)
-
~ wft" ! ' ' -"• "• ;ป:
-^1^1^- i *^ - =- 1 — -
!- ^t= :i^ :.,u Kli
^JiM^a -= - -i^s ^- : M, ;-:Tr=
. -:• i " •
_: --; ;T: ; ; ~_
•r-^H Binder or
i Stabilization Process
Reduction of
hexavalent chromium
followed by
stabilization with
cement and lime
Cement and a pH
adjustment agent
Water, ferric sulfate,
and Portland cement
Cement and ferrous
sulfate
Cement and ferrous
sulfate
Proprietary binder
f, ^_^__
^t,,. ^-5^=^
	 J:i HK^-s
Source
4.16
4.8
4.23
4.21,
4.22
4.21,
4.22
4.19
                                    4-8

-------
                                 Table 4.1
Solidification/Stabilization Treatment Performance Data for Arsenic (continued)


Project
Number
• • 1 ;••''•
Industry and Site
Type
1 • . - ; ! --
Waste or Media
;1 -', ' :
Scale"
Site Name, Location,
and Project
Completion Dateb
Initial Arsenic
Concentration
(mg/kg) or
Leachability
(mg/L) (Test
method)
! . 5 . , : r ':.:•'
•Final Arsenic
Concentration
(mg/kg) or
Leachability (mg/L)
(Test method)
Binder or
Stabilization Process
Source
Industrial Wastes
24
25

26
27
28
29
30
31
Food-grade H3P04
manufacture from
phosphate rock
Food-grade H3PO4
manufacture from
phosphate rock

Food-grade H3P04
manufacture from
phosphate rock
Food-grade H3P04
manufacture from
phosphate rock
—
—
—
--
"
Arsenous
trisulfide

Arsenous
trisulfide
Arsenous
trisulfide
Dry waste
Dry waste
Sludge
Sludge
Full
Full

Full
Full
Full
Full
Full
Full
—
—



-
—
-
—
70.0 mg/L (TCLP)
5,000 - 40,000
mg/kg
5,000 - 40,000
mg/kg
5,000 - 40,000
mg/kg
0.005 mg/L
(TCLP)
0.01 mg/L (EPT)
0.011 mg/L (EPT)
0.014 mg/L
(TCLP)
1.58 mg/L (TCLP)
0.43 mg/L (TCLP)
<0.14mg/L(TCLP)
<0. 10 mg/L (TCLP)
<0.002 mg/L (TCLP)
0.0023 mg/L (TCLP)
0.002 mg/L (EPT)
<0.002 mg/L (TCLP)
—
Oxidation with NaOH
and NaOCl followed
]by_ stabilization with _.
bed ash
Oxidation with
hydrated lime and
NaOCl followed by
stabilization with bed
ash
Pretreatment with
cement and CaOC12
followed by
stabilization with lime
and cement
Cement and other
unspecified additives
Cement and other
unspecified additives
Cement and other
unspecified additives
Cement and other
unspecified additives
4.1
4.1

4.1
4.1
4.4
4.4
4.4
4.4
                                   4-9

-------
                                Table 4.1
Solidification/Stabilization Treatment Performance Data for Arsenic (continued)
1 "" • * !'
Project
Number
32
33
34
35
36
37
38
39
40
41
Industry and Site
Type
Pesticide
Waste disposal
Waste treatment
Waste treatment
Glass Manufacturing
Glass Manufacturing
Glass Manufacturing
Mining


s* - -i - 'N. -*- ^_ ;fs
- ,=J = --_ = -- i =1 , i- ;
= -^^=|ij* ^ = 1, l-ilr tL, :lซ'
-:~^3i^^ I 4. i m. II- :!:
t= ; \ I:
Waste or Media
Pesticide sludge
Hazardous waste
landfill leachate
Hazardous waste
incinerator ash
Hazardous waste
incinerator pond
sludge
D004/D005
Waste
D004/D005
Waste
D004/D005
Waste
Mine Tailings
D004, spent
catalyst
P012,As203
Scale-
Full
Full
Full
Full
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
-• ' T~ • ' i
i * .
Site Name, Location,
and Project
Completion Date"
-
-
--
"~"
-
-
-
Spring Hill Mine,
Montana


iniS Arsenic
Concentration
(mg/kg) or
Leachability
(mg/L)(Test
method)
52.0 mg/L (WET)
19.0 mg/L (EPT)
4.20 mg/L (TCLP)
0.07 mg/L (TCLP)
0.30 mg/L (TCLP)
0.30 mg/L (EPT)
296 mg/L (TCLP)
6 mg/L (TCLP)
18 mg/L (TCLP)
6,000 mg/kg
280,000 mg/kg
750,000 mg/kg
ซ,,,ป, „„,„,„ t,.ซf,,ju^,ft,,
RraalApewcgujj;
Concentration
(mg/kg) or
Leachability (mg/L)
(Test method)
5.20 mg/L (WET)
0.14 mg/L (EPT)
0.016 mg/L (TCLP)
0.019 mg/L (TCLP)
O.01 mg/L (TCLP)
<0.01 mg/L (EPT)
66.3 mg/L (TCLP)
<1 mg/L (TCLP)
<1 mg/L (TCLP)
NDฐ (TCLP)
0.79 mg/L (TCLP)
1.25 mg/L (alkaline
leaching test at pH
9.5)
O.05 - 0.59 mg/L
(TCLP)
0.34 - 0.79 mg/L
(alkaline leaching test
atpH9.5)
^l*-1**'! *rn 	 *'"
Hrn::*: :
!: I -
--- Binder or
Stabilization Process
—
—
—
"
Cement and fly ash
Cement and fly ash and
ferrous sulfate
Cement and fly ash and
ferric sulfate
Silica
Microencapsulation
Chemical oxidation of
waste to form ferric
arsenate sludge,
followed by
stabilization with lime
Chemical oxidation of
waste to form ferric
arsenate sludge,
followed by
stabilization with lime
Source
4.1
4.1
4.1
4.1
4.14
4.14
4.14
4.17
4.3
4.3
                                   4-10

-------
                                                                     Table 4.1
                                  Solidification/Stabilization Treatment Performance Data for Arsenic (continued)


Project
Number
42
Industry and Site
Type

Waste or Media
Sludge
Scale"
Pilot
Site Name, Location,
and Project
Completion Dateb

Initial Arsenic
Concentration
(mg/kg) or
Leachability
(mg/L)(Test
method)
6,430 mg/L
Final Arsenic
Concentration
(mg/kg) or
Leachability (mg/L)
(Test method)
0.823 mg/L (TCLP)
Binder or
Stabilization Process
Embedding calcium
and ferric
arsenates/arsenites in a
cement matrix
Source
4.20
In Situ Stabilization Only
43

44
Agricultural
application of
pesticides
Wood preserving
wastes, soil, 50,000
cubic yards
Soil, 5,000 cubic
yards

Soil, 50,000
cubic yards
Full
Full
Wisconsin DNR-
QrcharcLSoil; 	
Silver Bow
Creek/Butte Area
Superfund Site, MT
1998
NDC - 50 mg/L
. (type of analysis
not reported)

NDC - 1 mg/L (type of
analysis notreported)

In situ treatment of
. contaminated, soil by
injecting pH
adjustment agents and
phosphates
In situ treatment of
contaminated soil by
injecting a solution of
ferrous iron, limestone,
and potassium
permanganate
4.6
4.8
a Excludes all bench-scale projects. Also excludes full- and pilot-scale projects where data on the leachability of stabilized wastes are not available.
b Project completion dates provided for Superfund remedial action projects only.
c Detection limit not provided.
d Analyzed after 28 days.  See Table 1.2 for long-term TCLP data.
EPT = Extraction procedure toxicity test.
- = Not available
WET = Waste extraction test
mg/kg = Milligrams per kilogram
TCLP = Toxicity characteristic leaching procedure
OU = Operable Unit
mg/L = Milligrams per liter
TWA = Total waste analysis
cy = Cubic yard
                                                                       4-11

-------
                                                                    Table 4.2
                                  Long-Term Solidification/Stabilization Treatment Performance Data for Arsenic
Project
Number
1
2
3
mtWPgHMfy^
^^^ TT^r'" ^r r~
Industry or Site
Type
Oil Processing &
Reclamation
Oil Processing &
Reclamation
Transformer and
Metal Salvage
BP**"yHII'H
'&*-- 'r *N
Waste or \
Media i
Filter cake
and oily
sludge
Soil
Soil
ti W""'q
~t : "
Fl ^ :
Scale"
Full
Full
Full
Site Name or :
Location
Imperial Oil Co. -
Champion
Chemical Co.
Superfund Site,
NJ
Imperial Oil Co. -
Champion
Chemical Co.
Superfund Site,
NJ
Portable
Equipment
Salvage Co., OR
iiwป^ซT1ปป*tlW;
-. Er_-.. ,,..
MtiatArsenic:
Concentration
(Total Waste
Analysis)
40mg/kg
92mg/kg
42mg/kg
. . ปi I. p. lapnfufTg'PBJg^1^
' !| ; - ' ,
j;; JlnMAr&enk .
Concentration of ,
Leachability
(28 day cure time)
NDh (TCLP)
0.017 mg/L (TCLP)
0.004 mg/L (TCLP)
Long-IPerm LeaSiaSe i Arsenic
Concentrafioni
(6 year cure time)
Archived
0.009 mg/L
(TCLP)
0.021 mg/L
(TCLP)

Field
0.005 mg/L
(TCLP)
0.022 mg/L
(TCLP)
0.005 mg/L
(TCLP)
Binder or
Stabilization
Process
Cement and
proprietary
additives
Cement and
proprietary
additives
Proprietary
binder
Source: 4.16

a Excludes all bench-scale projects.  Also excludes foil- and pilot-scale projects where data on the leachability of stabilized wastes are not available.
b Detection limit not provided.

— = Not available.
ND = Not detected.
TCLP = Toxicity characteristic leaching procedure.
                                                                       4-12

-------
5.0
VITRIFICATION FOR ARSENIC
  Summary

  Vitrification has been applied in a limited number of
  projects to treat arsenic-contaminated soil and waste.
  For soil treatment, the process can be applied either
  in situ or ex situ. This technology typically requires
  large amounts of energy to achieve vitrification
  temperatures* and therefore can be expensive to
  operate. Off-gases may require further treatment to
  remove hazardous constituents.
Model of an In Situ Vitrification System
                                                           Electrodes
                                                                                  Off-Gas
                                                                               to Treatment
                                                                                      Off-Gas
                                                                                      Collection
                                                                                      Hood
Technology Description and Principles        i
                                             i
During the vitrification treatment process, the metals
are surrounded by a glass matrix and become    ,
chemically bonded inside the matrix. For example,
arsenates can be converted into silicoarsenates during
vitrification (Ref. 5.4).                         |
  Technology Description: Vitrification is a high
  temperature treatment aimed at reducing the
  mobility of metals by incorporating them into a '
  chemically durable, leach resistant, vitreous mass
  (Ref. 5.6). This process also may cause
  contaminants to volatilize or undergo thermal  '.
  destruction, thereby reducing their concentration in
  the soil or waste.

  Media Treated
  •   Soil
      Waste                                 :

  Energy Sources Used for Vitrification:
  •   Fossil fuels
  •   Direct joule heat

  Energy Delivery Mechanisms Used for
  Vitrification:
  •   Arcs                               •    . •
  •   Plasma torches
  •   Microwaves
  •   Electrodes (in situ)

  In Situ Application Depth:                  •
  •   Maximum demonstrated depth is 20 feet
  •   Depths greater than 20 feet may require   '.
      innovative techniques
                                               Ex situ processes provide heat to a melter through a
                                               variety of sources, including combustion of fossil fuels,
                                               and input of electric energy by direct joule heating. The
                                               heat may be delivered via arcs, plasma torches, and
                                               microwaves. In situ vitrification uses resistance heating
                                               by passing an electric current through soil by means of
                                               an array of electrodes (Ref. 5.6). In situ vitrification
                                               can treat up to 1,000 tons of soil in a single melt.

                                               Vitrification occurs at temperatures from 2,000 to
                                               3,600ฐF (Ref.  5.1, 5.4).  These high temperatures may
                                               cause arsenic to volatilize and contaminate the off-gas
                                               of the vitrification unit.  Vitrification units typically
                                               employ treatment of the off-gas using air pollution
                                               control devices such as baghouses (Ref. 5.5).

                                               Pretreatment of the waste to be vitrified may reduce the
                                               contamination of off-gasses with arsenic.  For example,
                                               in one application (Project  15), prior to vitrification of
                                               flue dust containing arsenic trioxide (As2O3), a mixture
                                               of the flue dust and lime was roasted at 400 ฐC to
                                               convert the more volatile arsenic trioxide to less volatile
                                               calcium arsenate (Ca^AsO^) (Ref. 5.5).  Solid
                                               residues from off-gas treatment may be recycled into
                                               the feed to the vitrification unit (Ref. 5.6).

                                               The maximum treatment depth for in situ vitrification
                                               has  been demonstrated to be about 20 feet (Ref. 5.6).
                                               Table 5.1 describes specific vitrification processes used
                                               to treat soil and wastes containing arsenic.

                                               Media and Contaminants Treated

                                               Vitrification has been applied to soil and wastes
                                               contaminated with arsenic, metals, radionuclides, and
                                               organics. This method is a RCRA best demonstrated
                                               available technology (BOAT)  for various arsenic-
                                               containing hazardous wastes, including K031, K084,
                                               K101, K102, D004, and arsenic-containing P and U
                                               wastes  (Ref. 5.5, 5.6).
                                                   5-1

-------
Type, Number, and Scale of Identified Projects
Treating Soil and Wastes Containing Arsenic

Vitrification of arsenic-contaminated soil and waste has
been conducted at both pilot and full scale. The sources
for this report contained information on ex situ
vitrification of arsenic-contaminated soil at pilot scale
at three sites and at full scale at one site. Information
was  also identified for two in situ applications for
arsenic treatment at full scale.  In addition, 7 pilot-scale
and 3 full-scale applications to industrial waste were
identified.  Figure 5.1 shows the number of applications
identified at each scale.

                     Figure 5.1
 Scale of Identified Vitrification Projects for Arsenic
                     Treatment
 FUIL IE^LI
Pilot
     0                      5
Summary of Performance Data
Table 5.1 lists the vitrification performance data
identified in the sources used for this report. For ex situ
vitrification of soil, total arsenic concentrations prior to
treatment ranged from 8.7 to 540 mg/kg (Projects 2 and
4). Data on the leachability of arsenic from the vitrified
product were available only for Project 4, for which the
leachable arsenic concentration was reported as 0.9
mg/L.  For in situ vitrification of soil, total arsenic
concentrations prior to treatment ranged from 10.1 to
4,400 mg/kg (Projects 6 and 5, respectively). The
leachability of arsenic in the stabilized soil and waste
ranged from O.004 to 0.91 mg/L (Projects 5 and 6).

For treatment of industrial wastes, the total arsenic
concentrations prior to treatment ranged from 27 to
25,000 mg/kg (Projects 7 and 16) and leachable
concentrations in the vitrified waste ranged from 0.007
mg/L to 2.5 mg/L (Projects 15 and 16).  For some of the
projects listed in Table 5.1, the waste treated was
identified as a spent potliner from primary aluminum
reduction (RCRA waste code K088) but the
concentration of arsenic in the waste was not identified.
Some K088 wastes contain relatively low
concentrations of arsenic, and these projects may
involve treatment of such wastes.
The case study in this section discusses in greater detail
the in situ vitrification of arsenic-contaminated soil at
the Parsons Chemical Superfund Site.  This information
is summarized in Table 5.1, Project 6.
  Case Study:  Parsons Chemical Superfund Site
  Vitrification

  The Parsons Chemical Superfund Site in Grand
  Ledge, Michigan was an agricultural chemical
  manufacturing facility. Full-scale in situ
  vitrification was implemented to treat 3,000 cubic
  yards of arsenic-contaminated soil.  Initial arsenic
  concentrations ranged from 8.4 to 10.1 mg/kg. Eight
  separate melts were performed at the site, which
  reduced arsenic concentrations to 0.717 to 5.49
  mg/kg . The concentration of leachable arsenic in
  the treated soils ranged from O.004 to 0.0305
  mg/L, as measured by the TCLP. The off-gas
  emissions had arsenic concentrations of <0.000269
  mg/m3, O.59 mg/hr (see Table 5.1, Project 6).
Applicability, Advantages, and Potential Limitations

Arsenic concentrations present in soil or waste may
limit the performance of the vitrification treatment
process. For example, if the arsenic concentration in
the feed exceeds its solubility in glass, the technology's
effectiveness may be limited (Ref. 5.6).  Metals retained
in the melt must be dissolved to minimize the formation
of crystalline phases that can decrease leach resistance
of the vitrified product. The approximate solubility of
arsenic in silicate glass ranges from 1 - 3% by weight
(Ref. 5.7).

The presence of chlorides, fluorides, sulfides, and
sulfates may interfere with the process, resulting in
higher mobility of arsenic in the vitrified product.
Feeding additional slag-forming materials such as sand
to the process may compensate for the presence of
chlorides, fluorides, sulfides, and sulfates (Ref. 5.4).
Chlorides, such as those found  in chlorinated solvents,
in excess of 0.5 weight percent in the waste will
typically fume off and enter the off-gas. Chlorides in
the off-gas may result in the accumulation of salts of
alkali, alkaline earth, and heavy metals in the solid
residues collected by off-gas treatment.  If the residue is
returned to the process for treatment, separation of the
chloride salts from the residue may be necessary.  When
excess chlorides are present, dioxins and furans may
also form and enter the off-gas  treatment system (Ref.
5.6). The presence of these constituents may also lead
to the formation of volatile metal species or corrosive
acids in the off-gas (Ref. 5.7).
                                                    5-2

-------
During vitrification, combustion of the organic content
of the waste liberates heat, which will raise the    !
temperature of the waste, thus reducing the external
energy requirements. Therefore, this process may be
advantageous to wastes containing a combination Of
arsenic and organic contaminants or for the treatment of
organo-arsenic compounds. However, high      '
  Factors Affecting Vitrification Performance

  •   Presence of halogenated organic compounds -
     The combustion of halogenated organic
     compounds may result in incomplete combustion
     and the deposition of chlorides, which can result
     in higher mobility of arsenic hi the vitrified  .
     product (Ref. 5.4).
  •   Presence of volatile metals - The presence of
     volatile metals, such as mercury and cadmiurii,
     and other volatile inorganics, such as arsenic,;
     may require treatment of the off-gas to reduce air
     emissions of hazardous constituents (Ref. 5.6).
  •   Particle size -  Some vitrification units require
     that the particle size of the feed be controlled.
     For wastes containing refractory compounds that
     melt above the unit's nominal processing     '•
     temperature, such as quartz and alumina, size
     reduction may be required to achieve acceptable
     throughputs and a homogeneous melt.  High-;
     temperature processes, such as arcing and    ;
     plasma processes may not require size reduction
     of the feed (Ref. 5.6).                      ;
  •   Lack of glass-forming materials - If
     insufficient glass-forming materials  (SiO2 >30%
     by weight) and combined alkali (Na +  K > 1.4%
     by weight) are present  in the waste the vitrified
     product may be less durable. The addition of frit
     or flux additives may compensate for the lack of
     glass-forming and alkali materials (Ref. 5.6).
  •   Subsurface air pockets - For in situ
     vitrification, subsurface air pockets, such as
     those that may be associated with buried drums,
     can cause bubbling and splattering of molten
     material, resulting in a safety hazard (Ref. 5.10).
  •   Metals content - For in situ vitrification, a
     metals content greater than 15% by weight may
     result in pooling of molten metals at the bottom
     of the melt, resulting in electrical short-circuiting
     (Ref. 5.10).                               :
  •   Organic content - For in situ vitrification, an
     organic content of greater than 10% by weight
     may cause excessive heating of the melt,
     resulting in damage to  the treatment equipment
     (Ref. 5.10). High organics concentrations may
     also cause large volumes of off-gas as  the    :
     organics volatilize and combust, and may
     overwhelm air emissions control systems.
concentrations of organics and moisture may result in
high volumes of off-gas as organics volatilize and
combust and water turns to steam. This can overwhelm
emissions control systems.

Vitrification can also increase the density of treated
material, thereby reducing its volume.  In some cases,
the vitrified product can be reused or sold.  Vitrified
wastes containing arsenic have been reused as industrial
glass (Ref. 5.5). Metals retained in the melt that do not
dissolve in the glass phase can form crystalline phases
upon cooling that can decrease the leach resistance of
the vitrified product.

Excavation of soil is not required for in situ
vitrification. This technology has been demonstrated to
a depth of 20 feet.  Contamination present at greater
depths may require innovative application techniques.
In situ vitrification may be impeded by the presence of
subsurface air pockets, high metals concentrations, and
high organics concentrations (Ref. 5.10).
 Factors Affecting Vitrification Costs

 ซ   Moisture content - Greater than 5% moisture
     in the waste may result in greater mobility of
     arsenic in the final treated matrix. These
     wastes  may require drying prior to vitrification
     (Ref. 5.4). Wastes containing greater than 25%
     moisture content may require excessive fuel
     consumption or dewatering before treatment
     (Ref. 5.6).
 •   Characteristics of treated waste - Depending
     upon the qualities of the vitrified waste, the
     treated soil and waste may be able to be reused
     or sold.
 *   Factors affecting vitrification performance -
     Items in the "Factors Affecting Vitrification
     Performance" box will also affect costs.
Summary of Cost Data

Cost information for ex situ vitrification of soil and
wastes containing arsenic was not found in the
references identified for this report. The cost for in situ
vitrification of 3,000 cubic yards of soil containing
arsenic, mercury, lead, DDT, dieldrin and chlordane at
the Parsons Chemical Superfund site are presented
below (Ref. 5.8, cost year not provided):

    Treatability/pilot testing $50,000 - $ 150,000
    Mobilization $ 150,000 - $200,000
    Vitrification operation $375 - $4257 ton
    Demobilization $150,000 - $200,000
                                                    5-3

-------
References

5.1.  TIO. Database for EPA REACH IT (Remediation
     And Characterization Innovative Technologies).
     March 2001.  http://www.epareachit.org.
5.2.  U.S. EPA. Arsenic & Mercury - Workshop on
     Removal, Recovery, Treatment, and Disposal.
     Office of Research and Development. EPA-600-
     R-92-105. August 1992.
5.3.  U.S. EPA. BOAT Background Document for
     Spent Potliners from Primary Aluminum
     Reduction - K088. Office of Solid Waste.
     February 1996.
     http://yosemitel.epa.gov/EE/epa/ria.nsf/
     Ca2fb654a3ebbce28525648f007b8c26/22bebel32
     177e059852567e8006919c3?OpenDocument
5.4.  U.S. EPA. Best Demonstrated Available
     Technology (BOAT) Background Document for
     Wood Preserving Wastes: F032, F034, and F035;
     Final. April 1996.
     http://www.epa.gov/epaoswer/hazwaste/ldr/
     wood/bdat_bd.pdf
5.5.  U.S. EPA. Final Best Demonstrated Available
     Technology (BOAT) Background Document for
     K031, K084, K101, K102, Characteristic Arsenic
     Wastes (D004), Characteristic Selenium Wastes
     (DO 10), and P and U Wastes Containing Arsenic
     and Selenium Listing Constituents.  Office of
     Solid Waste.  May 1990.
5.6.  U.S. EPA Office of Research and Development.
     Engineering Bulletin, Technology Alternatives for
     the Remediation of Soils Contaminated with
     Arsenic, Cadmium, Chromium, Mercury, and
     Lead. Cincinnati, OH. March 1997.
     http://www.epa.gov/ncepi/Catalog/
     EPA540S97500.html
5.7.  U.S. EPA. Contaminants and Remedial Options at
     Selected Metal-Contaminated Sites. Office of
     Research and Development.  EPA-540-R-95-512.
     July 1995.
     http://www.epa.gov/ncepi/Catalog/
     EPA540R95512.html                     ;
5.8.  Federal Remediation Technologies Roundtable
     (FRTR). In Situ Vitrification at the Parsons
     Chemical/ETM Enterprises Superfund Site Grand
     Ledge, Michigan.
     http://www.frtr.gov/costperf.htm.
5.9.  FRTR. In Situ Vitrification,  U.S. Department of
     Energy, Hanford Site, Richland, Washington; Oak
     Ridge National Laboratory WAG 7; and Various
     Commercial Sites.
     http://www.frtr.gov/costperf.htm.
5.10  U.S. EPA. SITE Technology Capsule, Geosafe
     Corporation In Situ Vitrification Technology.
     Office of Research and Development. EPA
     540/R-94/520a. November 1994.
     http://www.epa.gov/ORD/SITE/reports/
     540_r-94_520a.pdf.
                                                 5-4

-------
                    Table 5.1
Vitrification Treatment Performance Data for Arsenic
Project
Number
Industry or Site
Type.:....
Media or
Waste
Scale"
Site Name or
Location
Initial Arsenic
Concentration
Vitrified Product and
Final Arsenic
Concentration
Vitrification Process
Description
Source
Environmental Media
1
2
3
4
5
Metal Ore Mining
and Smelting
Industrial Landfill


RCRA waste code
K031 and other
pesticide wastes
River and
harbor sludge
Mixture of
solids, soil,
and sludge
Soil, 400 tons
Soil

Pilot
Pilot
Full
Pilot
Full
Ecotechneik
B.V., Utrecht,
Netherlands
Matanza-
Riachuelo
River,
Monditech,
S.A., Buenos
Aires, Argentina
Chatham
Dockyard, St.
Mary's Island,
VERT, Kent,
England
University of
Pittsburgh
Applied
Research
Center,
Harmarville, PA

llVmg/kg
(TWA)
8.7 - 12 mg/kg
(TWA)

540 mg/kg
(TWA)
4,400 mg/kg
(TWA)
Artificial gravel
Artificial gravel, 0.01
mg/L (TCLP)
Glass fait
Glass cullet 0.9 mg/L
(TCLP)
0.91 mg/L (TCLP)
Rotary kiln vitrification at
1,150ฐC
Seizing, grinding, and
milling pretreatment
followed by vitrification in
a rotary kiln at 1,000ฐC
Wastes are mixed with
sand and limestone and fed
to a furnace containing a
pool of molten glass
maintained at 1550ฐC.
Glass is removed from
bottom of pool and water
cooled to produce fait.
Vortec Corporation
Advanced Combustion
Melting System, counter-
rotating vortex combustor
followed by cyclone melter
and water quench
In situ vitrification at 1200
degrees C with unspecified
air pollution control
equipment
5.1
5.1
5.1
5.2
5.5
                       5-5

-------
                         Table 5.1
Vitrification Treatment Performance Data for Arsenic (continued)
Project
Number
6
Industry or Site
Type
Agricultural
chemicals
manufacturing
Media or
Waste
Soil, 3,000
cubic yards
Scale8
Full
Site Name or
Location
Parsons
Chemical
Superfund Site,
MI
, Initial Arsenic
Concentration
8.4-10.1mg/kg
(TWA)
Vitrified Product and
Final Arsenic
Concentration
0.717 - 5.49 mg/kg
(TWA)
O.004 - 0.0305 mg/L
(TCLP)
Vitrification Process
Description
In situ vitrification, eight
separate melts. Stack gas
emissions of arsenic
O.000269 milligrams per
cubic meter, O.59
milligrams per hour.
Source
5.8
Industrial Waste
7
8
9
10
Incinerator air
pollution control
scrubber wastewater
Residues from
incineration of
municipal solid waste

Primary aluminum
reduction, RCRA
hazardous waste code
K088
Incinerator
ash
Fly ash
Hazardous
baghouse dust
Spent
potliners,
30,000 tons
per year
Pilot
Pilot
Pilot
Full
University of
Pittsburgh
Applied
Research
Center,
Harmarville, PA.
University of
Pittsburgh
Applied
Research
Center,
Harmarville, PA
University of
Pittsburgh
Applied
Research
Center,
Harmarville, PA
Barnard
Environmental,
Richland, WA
27 mg/kg (TWA)
981 mg/kg
(TWA)


Glass cullet 0.05 mg/L
(TCLP)
Glass cullet O.05 mg/L
(TCLP)
Glass cullet <0.02 mg/L
(TCLP)
Molten glass
Vortec Corporation
Advanced Combustion
Melting System, counter-
rotating vortex combustor
followed by cyclone melter
and water quench
Vortec Corporation
Advanced Combustion
Melting System, counter-
rotating vortex combustor
followed by cyclone melter
and water quench
Vortec Corporation
Advanced Combustion
Melting System, counter-
rotating vortex combustor
followed by cyclone melter
and water quench
Terra- Vit process,
resistance heating using
electrodes submerged in the
molten mass, molten glass
effluent is formed into
products
5.2
5.2
5.2
5.3
                            5-6

-------
                         Table 5.1
Vitrification Treatment Performance Data for Arsenic (continued)
Project
Number
11
12
13
14
Industry or Site
Type
Primary aluminum
reduction, RCRA
hazardous waste code
K088
Primary aluminum
reduction, RCRA
hazardous waste code
K088, and electric arc
furnace dust, RCRA
hazardous waste code
K066
Primary aluminum
reduction, RCRA
hazardous waste code
K088
Primary aluminum
reduction, RCRA
hazardous waste code
K088
Media or
Waste
Spent
potliners, 200
- 30ฐ
kilograms per
hour
Spent
potliners
Spent
potliners
Spent
potliners
Scale"
Pilot
Pilot
Pilot
Full
Site Name or
Location
Elkem
Technology,
Norway
Enviroscience,
Inc., Vancouver,
Washington
Ormet
Corporation
Reynolds
Metals
Initial Arsenic
Concentration




Vitrified Product and
Final Arsenic
Concentration
Slag
Slag wool
Industrial glass
Kiln residue has been
delisted, disposed at non-
hazardous landfill
Vitrification Process
Description
Slagging process with
addition of iron ore and
quartz
Extractive metallurgical
process conducted in a
shaft furnace to produce
zinc, calcium, and lead
oxides in the baghouse
dusfypig iron,-and mineral
wool
Spent potliners and glass-
forming ingredients are
vitrified in an in-flight
suspension combustor
followed by a cyclone
separation and melting
chamber
Spent potliners, limestone,
and brown sand are blended
and fed to a rotary kiln
vitrification unit
Source
5.3
5.3
5.3
5.3
                            5-7

-------
                                                         Table 5.1
                              Vitrification Treatment Performance Data for Arsenic (continued)
Project
Number
15
16
Industry or Site
Type

Phosphoric acid
production, RCRA
hazardous waste code
D004
Media orj
Waste
Flue dust
Sludge
containing
arsenic sulfide
Scale-
Full
Pilot
Site Name or
Location

Rhone-Poulenc
Initial Arsenic
Concentration

20,000 - 25,000
mg/kg(TWA)
Vitrified Product an^
Final Arsenic
Concentration
3,000 - 235,000 mg/kg
(TWA)
0.007-1. 8 mg/L (TCLP)
0.5 - 0.5 mg/L (EPT)
<0.5 - 2.5 mg/L (TCLP)
P.
Vitrification Process
Description
Roasting at 400 degrees C
to convert arsenic trioxide
to calcium arsenate
followed by vitrification in
an iron silicate slag at
1,290 degrees C

Source
5.5
5.5
a  Excluding bench-scale treatments
C = Celsius
EPT = Extraction procedure toxicity test
— = Not available
TCLP = Toxicity characteristic leaching procedure
TWA = Total waste analysis
WET = Waste extraction test
                                                            5-8

-------
 6.0     SOIL WASHING/ACID EXTRACTION
         FOR ARSENIC                       i
           Model of Soil Washing System
   Summary                                   ;

   Soil washing/acid extraction (soil washing) has been
   used to treat arsenic-contaminated soil in a limited
   number of applications.  The process is limited to:
   soils in which contaminants are preferentially
   adsorbed onto the fines fraction. The separated
   fines must be further treated to remove or
   immobilize arsenic.                           s
Technology Description and Principles          ;
                                               i
Soil washing uses particle size separation to reducejsoil
contaminant concentrations. This process is based on
the concept that most contaminants tend to bind to tjie
finer soil particles (clay, silt) rather than the larger i
particles (sand, gravel).  Because the finer particles iare
attached to larger particles through physical processes
(compaction and adhesion), physical methods can be
used to separate the relatively clean larger particles \
from the finer particles, thus concentrating the
contamination bound to the  finer particles  for further
treatment (Ref. 6.7).                             ;
                                               [
In this process, soil is first screened to remove     ;
oversized particles, and then homogenized. The soi^ is
then mixed with a wash solution consisting of water or
water enhanced with chemical additives such as    j
leaching agents, surfactants, acids, or chelating ageijts
to help remove organics and heavy metals.  The    j
particles are separated by size (cyclone and/or gravity
separation depending on the type of contaminants in the
soil and particle size), concentrating the contaminants
with the fines. Because the  soil washing process   i
removes and concentrates the contaminants but does not
destroy them, the resulting concentrated fines or sludge
usually require further treatment.  The coarser-grained
soil is generally relatively "clean", requiring no     j
  Technology Description: Soil washing is an ex
  situ technology that takes advantage of the behavior
  of some contaminants to preferentially adsorb onto
  the fines fraction. The soil is suspended in a wash'
  solution and the fines are separated from the
  suspension, thereby reducing the contaminant
  concentration in the remaining soil.

  Media Treated:
  •   Soil (ex situ)
additional treatment. Wash water from the process is
treated and either reused in the process, or disposed
(Ref. 6.7).  Commonly used methods for treating the
wastewater include ion exchange and solvent
extraction.

Media and Contaminants Treated

Soil washing is suitable for use on soils contaminated
with SVOCs, fuels, heavy metals, pesticides, and some
VOCs, and works best on homogenous, relatively
simple contaminant mixtures (Ref. 6.1, 6.4, 6.7). Soil
washing has been used to treat soils contaminated with
arsenic.

Type, Number, and Scale of Identified Projects
Treating Soil and Wastes Containing Arsenic

Nine projects were identified where soil washing was
performed to treat arsenic. Of these, four were
performed at full scale, including two at Superfund
sites. Three projects were conducted at pilot scale, and
two at bench scale (Ref. 6.4).  Figure 6.1 shows the
number of arsenic soil washing projects at bench, pilot,
and full scale.

                     Figure 6.1
  Scale of Identified Soil Washing/Acid Extraction
          Projects for Arsenic Treatment
                                                         Full
  Pilot
Bench
                                                   6-1

-------
 Case Study: King of Prussia Superfund Site

  The King of Prussia Superfund Site in Winslow
 Township, New Jersey is a former waste processing
 and recycling facility. Soils were contaminated with
 arsenic, berylllium, cadmium, chromium, copper,
 lead, mercury, nickel, selenium, silver, and zinc
 from the improper disposal of wastes (Project 1).
 Approximately 12,800 cubic yards of arsenic-
 contaminated soil, sludge, and sediment was treated
 using soil washing in 1993. The treatment reduced
 arsenic concentrations from 1 mg/kg to 0.31  mg/kg,
 a reduction of 69%.
Summary of Performance Data

Table 6.1. lists the available performance data.  For soil
and waste, this report focuses on performance data
expressed as the leachability of arsenic in the treated
material. However, arsenic leachability data are not
available for any of the projects in Table 6.1. The case
study in this section discusses in greater detail the soil
washing to treat arsenic at the King of Prussia
Superfund Site. This information is summarized in
Table 6.1, Project 1.

Applicability, Advantages, and Potential Limitations

The principal advantage of soil washing is that it can be
used to reduce the volume of material requiring further
treatment (Ref. 6.3).  However, this technology is
generally limited to soils with a range of particle size
distributions, and contaminants that preferentially
adsorb onto the fines fraction.

Summary of Cost Data

Table 6.1. shows the reported costs for soil washing to
treat arsenic. The unit costs range from $30 to $400 per
  Factors Affecting Soil Washing Costs

  •   Soil particle size distribution - Soils with a
      high proportion of fines may require disposal
      of a larger amount of treatment residual.
  •   Residuals management - Residuals from soil
      washing, including spent washing solution and
      removed fines, may require additional
      treatment prior to disposal.
  •   Factors affecting soil washing performance -
      Items in the "Factors Affecting Soil Washing
      Performance" box will also affect costs.
 Factors Affecting Soil Washing Performance

 •   Soil homogeneity - Soils that vary widely and
     frequently in characteristics such as soil type,
     contaminant type and concentration, and where
     blending for homogeneity is not feasible, may
     not be suitable for soil washing (Ref. 6.1).
     Multiple contaminants - Complex,
     heterogeneous contaminant compositions can
     make it difficult to formulate a simple washing
     solution, requiring the use of multiple,
     sequential washing processes to remove
     contaminants (Ref. 6.1).
 •   Moisture content - The moisture content of the
     soil may render its handling more difficult.
     Moisture content may be controlled by covering
     the excavation, storage, and treatment areas to
     reduce the amount of moisture in the soil (Ref.
     6.1).
 •   Temperature - Cold weather can cause the
     washing solution to freeze and can affect
     leaching rates (Ref. 6.1).
ton of material treated (costs not adjusted to a consistent
cost year). For one project treating 19,200 tons of soil,
sludge, and sediment (Table 6.1, Project 1), the total
reported treatment costs, including off-site disposal of
treatment residuals, was $7.7 million, or $400/ton (Ref.
6.6, 6.8, cost year not provided).

References

6.1.  U.S. EPA. Engineering Bulletin. Technology
     Alternatives for the Remediation of Soils
     Contaminated with Arsenic, Cadmium,
     Chromium, Mercury, and Lead. Office of
     Emergency and Remedial Response. 540-S-97-
     500. March 1997.
     http://www.epa.gov/ncepi/Catalog/
     EPA540S97500.html
6.2.  U.S. EPA.  A Citizen's Guide to Soil Washing.
     Office of Solid Waste and Emergency Response.
     EPA 542-F-96-002. April 1996.
     http://www.epa.gov/tio/download/remed/
     soilwash.pdf.
6.3.  U.S. EPA.  Treatment Technology Performance
     and Cost Data for Remediation of Wood
     Preserving Sites. Office of Research and
     Development. EPA-625-R-97-009. October
     1997.
     http ://www.epa.gov/ncepi/Catalog/
     EPA625R97009.html
6.4.  U.S. EPA.  Treatment Technologies for Site
     Cleanup: Annual Status Report (Tenth Edition).
                                                   6-2

-------
     Office of Solid Waste and Emergency Response.
     EPA-542-R-01-004.  February 2001.       ;
     http://clu-in.org/asr.                      ''
6.5.  U.S. EPA. Database for EPA REACH IT   |
     (REmediation And CHaracterization Innovative
     Technologies). March 2001.
     http://www.epareachit.org.
6.6.  U.S. EPA. Contaminants and Remedial Options
     at Selected Metal-Contaminated Sites. Office of
     Research and Development. EPA-540-R-95-512.
     July 1995.                              |
6.7.  Federal Remediation Technologies Roundtable:
     Remediation Technologies Screening Matrix and
     Reference Guide Version 3.0. November 2000.
     http://www.frtr.gov/matrix2/topjpage.html.
6.8.  Federal Remediation Technologies Roundtabje
     (FRTR). Soil Washing at the King of Prussia'
     Technical Corporation Superfund Site.      |
     http://www.frtr.gov/cosrperf.htm.
                                                 6-3

-------
                                                                 Table 6.1
                                    Arsenic Soil Washing Treatment Cost and Performance Data for Arsenic
Project
Number
1
2
3
4
5
6
7
8
9
Industry or Site
Type
Waste treatment,
recycling, and
disposal
Pesticide
manufacturing
Inorganic
chemical
manufacturing,
wood preserving
—
Herbicide
manufacturing,
explosives
manufacturing
Munitions
Manufacturing
Munitions
Manufacturing
Pesticide
manufacturing
Wood preserving
Waste or
Media
Soil
(12,800 cy)
Soil
(180,000 cy)
Soil
(5000 cy)
Soil
Soil (130 cy)
Soil,
sediments,
and other
solids
(400 cy)
Soil
Soil
Sediment
Scale
Full
Full
Full
Full
Pilot
Pilot
Pilot
Bench
Bench
Site Name or
Location
King of Prussia
Superfund Site,
Winslow Township,
NJ
Vineland Chemical
Company Superfund
Site, Operable Unit 01
Vineland, NJ
Ter Apel, Moerdijk,
Netherlands
—


—
Camp Pendleton
Marine Corps Base
Superfund Site, CA
Thunder Bay,
Ontario, Canada
Initial Arsenic
Concentration
1 mg/kg (TWA)

15-455mg/kg
(TWA)
250 mg/kg
(TWA)
97 - 227 mg/kg
(TWA)
2-129 mg/kg
(TWA)
--
4.5 mg/kg
(TWA)
9.1 mg/kg
(TWA)
Final Arsenic
Concentration
0.31 mg/kg
(TWA)

20 mg/kg (TWA)
20 mg/kg (TWA)
6.6 - 142 mg/kg
(TWA)
0.61-3.1
(mg/kg)
—
3 mg/kg (TWA)
0.015 mg/kg
(TWA)
Soil Washing Agent or
Process
Screening, separation, and
froth flotation


—


—

—
Cost
($/ton)"
$400


$100-
$300
$65
$80
—

—
Source
6.4, 6.8
6.4
6.5
6.6
6.5
6.5
6.5
6.5
6.3
a    Cost year not provided.

mg/kg = milligrams per kilogram    ~ = Not available    TWA = Total waste analysis
cy = Cubic yards
                                                                    6-4

-------
 7.0      PYROMETALLURGICAL RECOVERY
         FOR ARSENIC
   Summary

   Information gathered for this report indicate that
   pyrometallurgical processes have been implemented
   to recover arsenic from soil and wastes in four full-
   scale applications. These technologies may have
   only limited application because of their cost ($208
   - $458 per ton in 1991 dollars) and because the cost
   of importing arsenic is generally lower than
   reclaiming it using pyrometallurgical processes
   (Ref. 7.6). The average cost of imported arsenic
   metal in 1999 was $0.45 per pound (Ref. 7.6, in
   1999 dollars).  In order to make recovery
   economically feasible, the concentration of metals in
   the waste should be over 10,000 mg/kg (Ref. 7.2).
Technology Description and Principles
  Technology Description: Pyrometallurgical
  recovery processes use heat to convert an arsenic-
  contaminated waste feed into a product with a high
  arsenic concentration that can be reused or sold.

  Media Treated
  •    Soil                                   ;
  •    Industrial wastes                        ;

  Types of Pyrometallurgical Processes
  •    High temperature metals recovery
  •    Slag cleaning process                    ;
 Media and Contaminants Treated

 This technology has recovered heavy metals, such as
 arsenic and lead, from soil, sludge, and industrial
 wastes (Ref. 7.8).  The references used for this report
 contained information on applications of HTMR to
 recover arsenic from contaminated soil (Ref. 7.3) and
 secondary lead smelter soda slag (Ref. 7.8). In
 addition, one metals refining process that was modified
 to recover arsenic (Ref. 7.9) was identified.  The
 recycling and reuse of arsenic from consumer end-
 product scrap is not typically done (Ref. 7.6).

 Type, Number, and Scale of Identified Projects
 Treating Soil and Wastes Containing Arsenic

 This report identified application of pyrometallurgical
 recovery of arsenic at full scale at four facilities (Ref.
 7.3, 7.8, 7.9). No pilot-scale projects  for arsenic were
 found.

                     Figure 7.1
  Scale of Identified Pyrometallurgical Projects for
                Arsenic Treatment
  Full
 Pilot
A variety of processes reportedly have been used to
recover arsenic from soil and waste containing arsenic.
High temperature metals recovery (HTMR) involves
heating a waste feed to cause metals to volatilize or
"fume". The airborne metals are then removed with the
off-gas and recovered, while the residual solid materials
are disposed.  Other pyrometallurgical technologies
typically involve modifications at metal refining  :
facilities to recover arsenic from process residuals.
The Metallurgie-Hoboken-Overpelt (MHO) slag  ;
cleaning process involves blast smelting with the \
addition of coke as a reducing agent of primary ancl
secondary materials from lead, copper, and iron  '
smelting operations (Ref. 7.9).                  |
Summary of Performance Data

Table 7.1 presents the available performance data.
Because this technology typically generates a product
that is reused instead of disposed, the performance of
these processes is typically measured by the percent
removal of arsenic from the waste, the concentration of
arsenic in the recovered product, and the concentration
of impurities in the recovered product.  Other soil and
waste treatment processes are usually evaluated by
leach testing the treated materials.

Both of the soil projects identified have feed and treated
material arsenic concentrations. One project had an
                                                   7-1

-------
 arsenic feed concentration of 86 mg/kg and a treated
arsenic concentration of 6.9 mg/kg (Project 1).  The
other project had an leachable arsenic concentration in
the feed of 0.040 mg/L and 0.019 mg/L in the treated
material (Project 2).

Both of the industrial waste projects identified have
feed and residual arsenic data, and one has post-
treatment teachability data. The feed concentrations
ranged from 428 to 2,100 mg/kg (Projects 3 and 4).
The residual arsenic concentrations ranged from 92.1 to
 1,340 mg/kg, with less than 5 mg/L leachability (Project
3).

The case study in this section discusses in greater detail
an HTMR application at the National Smelting and
Refining Company Superfund Site. This information is
summarized in Table 7.1, Project 3.
  Case Study:  National Smelting and Refining
  Company Superfund Site, Atlanta, Georgia

  Secondary lead smelter slag from the National
  Smelting and Refining Company Superfund Site in
  Atlanta, Georgia was processed using high
  temperature metals recovery at a full-scale facility.
  The initial waste feed had an arsenic concentration
  range of 428 to 1,040 mg/kg. The effluent slag
  concentration ranged from 92.1 to 1,340 mg/kg of
  arsenic, but met project goals for arsenic leachability
  (<5 mg/L TCLP). The oxide from the baghouse
  fumes had an arsenic concentration of 1,010 to 1,170
  mg/kg; however, the arsenic was not recovered (Ref.
  7.8) (see Project 3, Table 7.1).
Applicability, Advantages, and Potential Limitations

Although recovering arsenic from soil and wastes is
feasible, it has not been done in the U.S. on a large
scale because it is generally less expensive to import
arsenic than to obtain it through reclamation processes
(Ref. 7.5-7).  The cost of importing arsenic in 1999 was
approximately $0.45 per pound (Ref. 7.6, in 1999 •
dollars). In order to make recovery economically
feasible, the concentration of metals in the waste should
be over 10,000 mg/kg (Ref. 7.2). In some cases, the
presence of other metals in the waste, such as copper,
may provide sufficient economic incentive to recover
copper and arsenic together for the manufacture of
arsenical wood preservatives (Ref. 7.1). However,
concern over the toxicity of arsenical wood
preservatives is leading to its phase-out (Ref. 7.10).
 Factors Affecting Pyrometallurgical Recovery
 Performance

 •   Particle size - Larger particles do not allow
     heat transfer between the gas and solid phases
     during HTMR.  Smaller particles may increase
     the particulate in the off-gas.
 •   Moisture content - A high water content
     generally reduces the efficiency of HTMR
     because it increases energy requirements.
     Thermal conductivity - Higher thermal
     conductivity of the waste results in better heat
     transfer into the waste matrix during HTMR
     (Ref. 7.2).
 •   Presence of impurities - Impurities, such as
     other heavy metals, may need to be removed,
     which increases the complexity of the treatment
     process.
At present, arsenic is not being recovered domestically
from arsenical residues and dusts at nonferrous
smelters, although some of these materials are
processed for the recovery of other materials (Ref. 7.6).

This technology may produce treatment residuals such
as slag, flue dust, and baghouse dust. Although some
residuals may be treated using the same process that
generated them, the residuals may require additional
treatment or disposal.

Summary of Cost Data

The estimated cost of treatment using HTMR ranges
from $208 to  $458 per ton (in  1991 dollars). However,
these costs are not specific to treatment of arsenic (Ref.
7.2). No cost data for pyrometallurgical recovery for
arsenic was found.
  Factors Affecting Pyrometallurgical Recovery
  Costs

      Factors affecting pyrometallurgical recovery
      performance - Items in the "Factors Affecting
      Pyrometallurgical Recovey Performance" box
      will also affect costs.
                                                    7-2

-------
 References
 7.1   U.S. EPA. Arsenic & Mercury - Workshop on
      Removal, Recovery, Treatment, and Disposal.
      Office of Research and Development. EPA-6JOO-
      R-92-105. August 1992.                  !
 7.2   U.S. EPA. Contaminants and Remedial Options
      at Selected Metal-Contaminated Sites. Office of
      Research and Development. EPA-540-R-95-512.
      July 1995. http://www.epa.gov/ncepi/Catalog/
      EPA540R95512.htmT                    i
 7.3   U.S. EPA National Risk Management Research
      Laboratory. Treatability Database. March 2001.
 7.4   Code of Federal Regulations, Part 40, Section
      268. http://lula.law.cornell.edu/cfr/         i
      cfr.php?title=40&type=part&value=268     \
 7.5   U.S. EPA. Final Best Demonstrated Available
      Technology (BOAT) Background Document for
      K031, K084, K101, K102, Characteristic Arsenic
      Wastes (D004), Characteristic Selenium Wasjes
      (DO 10), and P and U Wastes Containing Arsenic '
      and Selenium Listing Constituents. Office of
      Solid Waste. May 1990.                   •
 7.6   U.S. Geological Survey. Mineral Commodity
      Summaries. February 2000.
      http://minerals.usgs.gov/minerals/pubs/
      commodity/soda_ash/610300.pdf
 7.7   U.S. EPA.  Engineering Bulletin. Technology
      Alternatives for the Remediation of Soils
      Contaminated with Arsenic, Cadmium,
      Chromium, Mercury, and Lead. Office of
      Emergency and Remedial Response. March 1997.
     http ://www.epa.gov/ncepi/Catalog/
     EPA540S97500.html
 7.8  U.S. EPA.  Superfund Innovative Technology
     Evaluation Program. Technology Profiles Tenth
     Edition. Volume 1 Demonstration Program.
     Office of Research and Development. EPA-540-
     R-99-500a. February 1999.
     http://www.epa.gov/ncepi/Catalog/
     EPA540R99500A.html
7.9  U.S. EPA. Profiles of Metal Recovery
     Technologies for Mineral Processing and Other
     Metal-Bearing Hazardous Wastes. December
     1994.
7.10  U.S. EPA. Manufacturers to Use New Wood
     Preservatives, Replacing Most Residential Uses of
     CCA. February 12, 2002.
     http://www.epa.gov/pesticides/citixens/
     cca transition.htm
                                                 7-3

-------
                                                                Table 7.1
                                      Arsenic Pyroraetallurgical Recovery Performance Data for Arsenic


Project
Number

Industry ! -'<
or Site
Type

Media or
Waste
Reclaimed



Scale


Site Name or
Location
Reclamation
Process Feed
Arsenic
Concentration

Reclamation Process
Residual Arsenic
Concentration


Recovered Arsenic
Concentration


Reclamation
Process Used

1
!
Source
Environmental Media 	 . 	 _ 	 , 	
1

2

—

~

Soil (amount not
available)
Soil (amount not
available)
Full

Full

-

-

86mg/kg(TWA)

0.040 mg/L (TCLP)

6.9 mg/kg (TWA)

0.019 mg/L (TCLP)

—

—

HTMR

HTMR

7.3

7.3

Industrial Wastes 	 , 	 , 	
3






4







	






„-







Secondary lead
smelter soda
slag (72 tons)
-



Primary and
secondary
materials
(additional
description of
materials not
available)

Full






Full







National
Smelting and
Refining
Company
Superfund
Site, Atlanta,
GA
Hoboken,
Belgium






428 - 1,040 mg/kg
(TWA)





2,100 mg/kg
(TWA)






Slag, 92.1 - 1,340
mg/kg (TWA)
Slag, <5 mg/L (TCLP)




Slag, 100 mg/kg
(TWA)
zinc flue dust, 1,000
mg/kg (TWA)




Arsenic trioxide,
1,010 -1,170 mg/kg
(TWA)
. . .



Lead-copper-iron
alloy, 52,000 mg/kg
(TWA)
lead bullion, 3,900
mg/kg (TWA)
Arsenic trioxide
(concentration not
available)
HTMR






MHO







7.8






7.9







TCLP = Toxicity Characteristic Leaching Procedure.
- = Not available
MHO = Metallurgie-Hoboken-Overpelt process.
TWA = Total Waste Analysis.
HTMR = High Temperature Metals Recovery.
                                                                    7-4

-------
 8.0
IN SITU SOIL FLUSHING FOR ARSENIC
  Summary

  Data gathered for this report show that in situ soil
  flushing has been used to treat arsenic-contaminated
  soils in a limited number of applications. Two
  projects have been identified that are currently  ;
  operating at full scale, but performance results are
  not yet available.
Technology Description and Principles

In situ soil flushing techniques may employ water <>r a
mixture of water and additives as the flushing solution.
Additives may include acids (sulfuric, hydrochloric,
nitric, phosphoric, or carbonic acid), bases (for    j
example, sodium hydroxide), chelating or completing
agents (such as EDTA), reducing agents, or surfactant
to aid in the desorption and dissolution of the targejt
contaminants (Ref. 8.1).                        i

Subsurface containment barriers or other hydraulic
controls have sometimes been used in conjunction With
soil flushing to help control the flow of flushing fluids
and assist in the capture of the contaminated fluid.
Impermeable membranes have also been used in soime
cases to limit infiltration of groundwater, which could
cause dilution of flushing solutions and loss of    ]
hydraulic control (Ref. 8.1).                     !
  Technology Description: In situ soil flushing is a
  technology that extracts organic and inorganic   ;
  contaminants from soil by using water, a solution: of
  chemicals in water, or an organic extractant, without
  excavating the contaminated material itself. The
  solution is injected into or sprayed onto the area of
  contamination, causing the contaminants to become
  mobilized by dissolution or emulsification. After
  passing through the contamination zone, the     !
  contaminant-bearing flushing solution is collected
  by downgradient wells or trenches and pumped to
  the surface for removal, treatment, discharge, or ;
  reinjection (Ref. 8.1).

  Media Treated:
  •    Soil (in situ)
Media and Contaminants Treated

Soil flushing has been used to treat soils in situ
contaminated with organic, inorganic, and metal
contaminants (Ref. 8.1), including arsenic.
Model of an In Situ Flushing System
1

Surfactant, Cosolvent,
or Water Mixture
r

1
Ground Surface
•ซ*. Contaminated Soil — "
=3
                                              Type, Number, and Scale of Identified Projects
                                              Treating Soil Containing Arsenic

                                              The references identified for this report contained
                                              information on two full-scale in situ soil flushing
                                              projects for the treatment of arsenic at two Superfund
                                              sites (Ref. 8.4), and two at pilot scale at two other sites
                                              (Ref. 8.6, 8.7). At one of the Superfund sites, 150,000
                                              cubic yards of soil are being treated, while at the other
                                              19,000 cubic yards of soil are being treated. Figure 8.1
                                              shows the number of projects identified at pilot and full
                                              scale.

                                                                   Figure 8.1
                                               Scale of Identified In Situ Soil Flushing Projects for
                                                               Arsenic  Treatment
                                                 Fun
                                                Pflot
                                              Summary of Performance Data

                                              Arsenic treatment is ongoing at two Superfund sites
                                              using in situ soil flushing, and has been completed at
                                              two other sites (Ref. 8.3, 8.4, 8.6, 8.7). Performance
                                              data for the Superfund site projects are not yet available
                                                   8-1

-------
 Case Study: Vineland Chemical Company
 Superfund Site

 The Vineland Chemical Company Superfund Site in
 Vineland, New Jersey is a former manufacturing
 facility for herbicides containing arsenic. Soils
 were contaminated with arsenic from the improper
 storage and disposal of herbicide by-product salts
 (RCRA waste code K031).  Approximately 150,000
 cubic yards of soil were treated. Pretreatment
 arsenic concentrations were as high as 650 mg/kg.
 The soil was flushed with groundwater from the
 site, which was extracted, treated to remove arsenic,
 and reinjected into the contaminated soil. Because
 the species of arsenic contaminating the soil is
 highly soluble in water, the addition of surfactants
 and cosolvents was not necessary. No data are
 currently available on the treatment performance
 (Ref. 8.3, 8.4, 8.8) (see Project 1, Table 8.1). The
 remedy at this site was changed to soil washing in
 order to reduce treatment cost and the time needed
 to remediate the site.
as the projects are ongoing.  Performance data are also
not available for the other two projects. See Table 8.1
for information on these projects. The case study in this
section discusses in greater detail a soil flushing
application at the Vineland Chemical Company
Superfund Site.  This information is summarized in
Table 8.1, Project 3.
  Factors Affecting Soil Flushing Performance

  •    Number of contaminants treated - The
      technology works best when a single
      contaminant is targeted. Identifying a flushing
      fluid that can effectively remove multiple
      contaminants may be difficult (Ref. 8.1).
  •    Soil characteristics - Some soil characteristics
      may effect the performance of soil flushing.
      For example, an acidic flushing solution may
      have reduced effectiveness in an alkaline soil
      (Ref. 8.1).
  •    Precipitation - Soil flushing may cause arsenic
      or other chemicals in the soil to precipitate and
      obstruct the soil pore structure and inhibit flow
      through the soil (Ref. 8.1).
  *    Temperature - Low temperatures may cause
      the flushing solution to freeze, particularly
      when shallow infiltration galleries and above-
      ground sprays are used to apply the flushing
      solution (8.1).
Applicability, Advantages, and Potential Limitations

The equipment used for in situ soil flushing is relatively
easy to construct and operate, and the process does not
involve excavation or disposal of the soil, thereby
avoiding the expense and hazards associated with these
activities (Ref. 8.1). Spent flushing solutions may
require treatment to remove contaminants prior to reuse
or disposal. Treatment of flushing fluid results in
process sludges and residual solids, such as spent
carbon and spent ion exchange resin, which may require
treatment before disposal. In some cases, the spent
flushing solution may be discharged to a publicly-
owned treatment works (POTW), or reused in the
flushing process. Residual flushing additives in the soil
may be a concern and should be evaluated on a site-
specific basis (Ref. 8.1). In addition, soil flushing may
cause contaminants to mobilize and spread to
uncontaminated areas of soil or groundwater.
  Factors Affecting Soil Flushing Costs

  •    Reuse of flushing solution - The ability to
      reuse the flushing solution may reduce the cost
      by reducing the amount of flushing solution
      required (Ref. 8.1).
      Contaminant recovery - Recovery of
      contaminants from the flushing solution and the
      reuse or sale of recovered contaminants may be
      possible in some cases (Ref. 8.3, 8.4).
  •    Factors affecting soil flushing performance -
      Items in the "Factors Affecting Soil Flushing
      Performance" box will also affect costs.
Summary of Cost Data

No data are currently available on the cost of soil
flushing systems used to treat arsenic.

References

8.1. U.S. EPA. Engineering Bulletin. Technology
     Alternatives for the Remediation of Soils
     Contaminated with Arsenic, Cadmium,
     Chromium, Mercury, and Lead. Office of
     Emergency and Remedial Response. EPA 540-S-
     97-500. March 1997.
     http://www.epa.gov/ncepi/Catalog/
     EPA540S97500.html
                                                     80
                                                    -Z

-------
8.2.  U.S. EPA. Contaminants and Remedial Options
     at Selected Metal-Contaminated Sites.  Office of
     Research and Development.  EPA-540-R-9f!-512
     July 1995.                             l
     http://www.epa.gov/ncepi/Catalog/        i
     EPA540R95512.html                   ;
8.3.  U.S. EPA. Database for EPA REACH IT  [
     (REmediation And CHaracterization Innovative
     Technologies). March 2001.             !
     http://www.epareachit.org.               ;
8.4.  U.S. EPA. Treatment Technologies for Site!
     Cleanup: Annual Status Report (Tenth Edition).
     Office of Solid Waste and Emergency Response.
     EPA-542-R-01-004.  February 2001.      i
     http://www.epa.gov/ncepi/Catalog/
     EPA542R01004.html                   '
8.5.  U.S. EPA. Recent Developments for In Situ
     Treatment of Metals Contaminated Soil. EPA
     March 1997. http://clu-in.org            \
8.6  Redwine JC. Innovative Technologies for  j
     Remediation of Arsenic in Soil and Ground^ater.
     Southern Company Services, Inc. Presented kt the
     Air and Waste Management Association's 93rd
     Annual Conference and Exhibition, Salt Lake
     City, June, 2000.                         i
8.7  Miller JP, Hartsfield TH, Corey AC, Markey RM.
     In Situ Environmental Remediation of an   |
     Energized Substation. EPRI. Palo Alto, CA;
     Report No. 1005169. 2001.
8.8  U.S. EPA. Vineland Chemical Company, Inc.
     Fact Sheet. April 2002.        '          j
     http://www.epa.gov/region02/            •
     superfund/npl/0200209c.pdf              !
                                                 8-3

-------
                                                                  Table 8.1
                                          Arsenic In Situ Soil Flushing Performance Data for Arsenic
Project
Number
1
2
3
4
Industry or
Site Tvpe
Pesticide
manufacturing
Primary
aluminum
production
Power
substation
Power
substation
Waste or
Media
Soil
(150,000 cy)
Soil
(19,000 cy)
Soil
Soil
Scale
Full
Full
Pilot
Pilot
Site Name or
Location
Vineland Chemical
Company Superfund
Site, Operable Unit 01
Vineland, NJ
Ormet Superfund Site,
Hannibal, OH
Ft. Walton Beach, FL
Florida
Initial Arsenic
Concentration
20 - 650 mg/kg
(TWA)

—

Final Arsenic
Concentration

0.027 mg/L
—

Soil Flushing Agent or
Process
Flushing with groundwater
followed by extraction,
treatment, and reuse to flush
soil. Project was changed to
soil washing prior to
completion.
Flushing with water followed
by extraction, treatment, and
discharge to surface water
under an NPDES permit.
Project completion is
expected in 2007.
Flushing with 0.01 M
phosphoric acid.
Treatment train consisting of
flushing with citric acid
followed by iron
coprecipitation and ceramic
membrane filtration.
Source
8.3, 8.4,
8.8
8.3, 8.4
8.7
8.6
mg/kg = milligrams per kilogram

— = Not available
mg/L = milligrams per liter

TWA = Total waste analysis
                                                                     8-4

-------
                IIB
ARSENIC TREATMENT TECHNOLOGIES
      APPLICABLE TO WATER

-------

-------
9.0     PRECIPITATION/COPRECIPITATION
        FOR ARSENIC                      '•
  Summary

  Precipitation/coprecipitation has been the most  :
  frequently used method to treat arsenic-        ;
  contaminated water, including groundwater, surface
  water, leachate, mine drainage, drinking water, and
  wastewater in numerous pilot- and full-scale
  applications.  Based on the information collected to
  prepare this report, this technology typically can
  reduce arsenic concentrations to less than 0.050
  mg/L and in some cases has reduced arsenic    •
  concentrations to below 0.010 mg/L.
Technology Description and Principles

For this report, technologies were considered     j
precipitation/coprecipitation if they involved the  |
following steps:                                j

•   Mixing of treatment chemicals into the water;
•   Formation of a solid matrix through precipitation,
    coprecipitation, or a combination of these    ;
    processes, and
•   Separation of the solid matrix from the water I
                                              i
Technologies that remove arsenic by passing it through
a fixed bed of media, where the arsenic may be   •
removed through adsorption, precipitation/       I
coprecipitation, or a combination of these processes, are
discussed in the adsorption treatment section (Section
11.0).                                         j

Precipitation/coprecipitation usually involves pH  ,
adjustment and addition of a chemical precipitant 6r
  Technology Description:  Precipitation uses
  chemicals to transform dissolved contaminants into
  an insoluble solid.  In coprecipitation, the target
  contaminant may be dissolved or in a colloidal or
  suspended form. Dissolved contaminants do not
  precipitate, but are adsorbed onto another species
  that is precipitated. Colloidal or suspended
  contaminants become enmeshed with other
  precipitated species, or are removed through
  processes such as coagulation and flocculation.
  Many processes to remove arsenic from water
  involve a combination of precipitation and
  coprecipitation. The precipitated/coprecipitated
  solid is then removed from the liquid phase by
  clarification or filtration. Arsenic precipitation/
  coprecipitation can use combinations of the
  chemicals and methods listed below.
  Media Treated:
  •  Drinking water
  •  Groundwater
  •  Wastewater
Surface water
Leachate
Mine drainage
  Chemicals and Methods Used for Arsenic
  Precipitation/Coprecipitation:
    Ferric salts, (e.g.,
    ferric chloride), ferric
    sulfate, ferric
    hydroxide
    Ammonium sulfate
    Alum (aluminum
    hydroxide)
pH adjustment
Lime softening,
limestone, calcium
hydroxide
Manganese sulfate
Copper sulfate
Sulfide
coagulant; it can also include addition of a chemical
oxidant (Ref. 9.1).  Oxidation of arsenic to its less
soluble As(V) state can increase the effectiveness of
Model of a Precipitation/Coprecipitation System

1
Oxidation/
Reduction
(Pretreatment
Process)
Groundwater
Soh'ds to -^
Disposal
Reagent

"1 i ~1

Polymer

	 *- Effluent
_______ ^^^SE. ^-^^^^
TT.,.,,, .„, , .. T i Clarification
pH Adjustment ^nd Flocculation i 1
Reagent Addition i 1
i
Filtrate T
! c
Sludge ^
Dewatering
•
' 1

)verflow ^t- ^^J
Sludge | S] fl
Thickening
                                                   9-1

-------
precipitation/coprecipitation processes, and can be done
as a separate pretreatment step or as part of the
precipitation process.  Some pretreatment processes that
oxidize As(III) to As(V) include ozonation, photo
oxidation, or the addition of oxidizing chemicals such
as potassium permanganate, sodium hypochlorite, or
hydrogen peroxide (Ref. 9.8, 9.16, 9.22,  9.25, 9.29).
Clarification or filtration are commonly used to remove
the solid precipitate.

Media and Contaminants Treated

Precipitation/coprecipitation is frequently used to treat
water contaminated with metals (Ref. 9.1). The
references identified for this report contained
information on its application to industrial wastewater,
groundwater, surface water, leachate, and mine    !
drainage.

Type, Number, and Scale of Identified Projects
Treating Water Containing Arsenic

Precipitation/coprecipitation processes for arsenic in
drinking water, groundwater,  and industrial wastewater
are commercially available. The data gathered hi
support of this report include  information on its full-
scale application at 16 sites. Information on  full-scale
treatment of drinking water is available for eight
facilities and of industrial wastewater for 21 facilities.
Information on 24 pilot-scale applications was also
identified.  Figure 9.1 shows the number of pilot- and
full-scale precipitation/coprecipitation projects in the
sources researched.

                     Figure 9.1
   Scale  of Identified Precipitation/Coprecipitation
           Projects for Arsenic Treatment
 Pilot
       0       10      20       30      40      50
Summary of Performance Data

Table 9.1 presents the available performance data for
pilot- and full-scale precipitation/coprecipitation
  Precipitation/Coprecipitation Chemistry

  The chemistry of precipitation/coprecipitation is
  often complex, and depends upon a variety of
  factors, including the speciation of arsenic, the
  chemical precipitants used and their concentrations,
  the pH of the water, and the presence of other
  chemicals  in the water to be treated. As a result, the
  particular mechanism that results in the removal of
  arsenic through precipitation/coprecipitation
  treatment is process-specific, and in some cases is
  not completely understood.  For example, the
  removal mechanism in the treatment of As(V) with
  Fe(III) has been debated in the technical literature
  (Ref. 9.33).

  It is beyond the scope of this report to provide all
  possible chemical reactions and mechanisms for
  precipitation/coprecipitation processes that are used
  to remove arsenic.  More detailed information on the
  chemistry  involved in specific processes can be
  found in the references listed at the end of this
  section.
treatment. It contains information on 69 applications,
including 20 groundwater, surface water, and mine
drainage, 15 drinking water, and 34 industrial
wastewater projects.  The information that appears in
the "Precipitating Agent or Process" column of Table
9.1, including the chemicals used, the descriptions of
the processes, and whether it involved precipitation or
coprecipitation, is based on the cited references.  This
information was not independently checked for
accuracy or technical feasability. For example, in some
cases, the reference used may apply the term
"precipitation" to a process that is actually
coprecipitation.

The effectiveness of this technology can be evaluated
by comparing influent and effluent contaminant
concentrations. All of the 12 environmental media
projects for which both influent and effluent arsenic
concentration data were available had influent
concentrations greater than 0.050 mg/L. The treatments
achieved effluent concentrations of less than 0.050
mg/L in eight of the projects and less than 0.010 mg/L
in four of the projects.  Information on the leachability
of arsenic from the precipitates and sludges was
available for three projects. For all of these projects, the
concentration of leachable arsenic as measured by the
toxicity characteristic leaching procedure  (TCLP) (the
RCRA regulatory threshold for identifying a waste that
is hazardous because it exhibits the characteristic of
toxicity for arsenic) was below 5.0 mg/L.
                                                    9-2

-------
   Factors Affecting Precipitation/Coprecipitation
   Performance

       Valence state of arsenic - The presence of the
       more soluble trivalent state of arsenic may ;
       reduce the removal efficiency. The solubility of
       arsenic depends upon its valence state, pH, the
       specific arsenic compound, and the presence of
       other chemicals with which arsenic might react
       (Ref. 9.12). Oxidation to As(V) could improve
       arsenic removal through precipitation/     i
       coprecipitation (Ref. 9.7).               ;
       pH - In general, arsenic removal will be
       maximized at the pH at which the precipitated
       species is least soluble.  The optimal pH range
       for precipitation/coprecipitation depends upon
       the waste treated and the specific treatment '
       process (Ref. 9.7).                       :
       Presence of other compounds - The presence
       of other metals or contaminants may impact the
       effectiveness of precipitation/coprecipitatiori.
       For example, sulfate could decrease arsenic
       removal in processes using ferric chloride as a
       coagulant, while the presence of calcium or iron
       may increase the removal of arsenic in these
       processes (Ref. 9.7).                     '.
 Information on treatment goals was not collected for
 this report.

 Some projects in Table 9.1 include treatment trains, the
 most common being precipitation/coprecipitation
 followed by activated carbon adsorption or membrane
 filtration. In those cases, the performance data listed
 are for the entire treatment train, not just the
 precipitation/coprecipitation step.

 The case study in this section discusses in greater detail
 the removal of arsenic from groundwater using an
 aboveground treatment system at the Winthrop Landfill
 Superfund site. This information is summarized in
 Table 9.1, Project 1.

 Applicability, Advantages,  and Potential Limitations

 Precipitation/coprecipitation is an active ex situ
 treatment technology designed to function with routine
 chemical addition and sludge removal. It usually
 generates a sludge residual, which typically requires
 treatment such as dewatering and subsequent disposal.
 Some sludge from the precipitation/coprecipitation of
 arsenic can be a hazardous waste and require additional
treatment such as solidification/stabilization prior to
disposal. In the presence of other metals or
Of the 12 drinking water projects having both influent
and effluent arsenic concentration data, eight had  j
influent concentrations greater than 0.050 mg/L. The
treatments achieved effluent concentrations of lessithan
0.050 mg/L in all eight of these projects, and less than
0.010 mg/L in two projects.  Information on the   ;
leachability of arsenic from the precipitates and sludges
was available for six projects.  For these projects the
leachable concentration of arsenic was below 5.0 nig/L.

All of the 28  wastewater projects having both influent
and effluent arsenic concentration data had influent
concentrations greater than 0.050 mg/L.  TheTreatments
achieved effluent concentrations of less than 0.050!
mg/L in 16 of these projects, and less than 0.010 mg/L
in 11 projects. Information on the leachability of  |
arsenic from the precipitates and sludges was available
for four projects.  Only one of these projects had a '
leachable concentration of arsenic below 5.0 mg/L.I
                                               i
Projects that did not reduce effluent arsenic       i
concentrations to below 0.050 or 0.010 mg/L do not
necessarily indicate that precipitation/coprecipitation
cannot achieve these levels. The treatment goal for I
some applications could have been above these    |
concentrations, and the technology may have been ]
designed and  operated to meet a higher concentration.
  Case Study: Winthrop Landfill Site

  The Winthrop Landfill Site, located in Winthrop,
  Maine, is a former dump site that accepted
  municipal and industrial wastes (See Table 9.1,
  Project 1). Groundwater at the site was
  contaminated with arsenic and chlorinated and
  nonchlorinated VOCs. A pump-and-treat system for
  the groundwater has been in operation at the site
  since 1995. Organic compounds have been
  remediated to below action levels, and the pump-
  and-treat system is currently being operated for the
  removal of arsenic alone. The treatment train
  consists of equalization/pH adjustment to pH 3,
  chemical oxidation with hydrogen peroxide,
  precipitation/coprecipitation via pH adjustment to
  PH 7, flocculation/clarification, and sand bed
  filtration. It treats 65 gallons per minute of
  groundwater containing average arsenic
  concentrations of 0.3 mg/L to below 0.005 mg/L.
  Through May, 2001,359 pounds of arsenic had
  been removed from groundwater at the Winthrop
  Landfill Site using this above ground treatment
  system. Capital costs for the system were about $2
  million, and O&M costs are approximately
  $250,000 per year (Ref. 9.29, cost year not
  provided).
                                                   9-3

-------
 Factors Affecting Precipitation/Coprecipitation
 Costs

 •   Type of chemical addition - The chemical
     added will affect costs. For example, calcium
     hypochlorite, is a less expensive oxidant than
     potassium permanganate (Ref. 9.16).
 •   Chemical dosage - The cost generally
     increases with increased chemical addition.
     Larger amounts of chemicals added usually
     results in a larger amount of sludge requiring
     additional treatment or disposal (Ref. 9.7,
     9.12).
 •   Treatment goal - Application could require
     additional treatment to meet stringent cleanup
     goals and/or effluent and disposal standards
     (Ref. 9.7)
 •   Sludge disposal - Sludge produced from the
     precipitation/coprecipitation process could be
     considered a hazardous waste and require
     additional treatment before disposal, or disposal
     as hazardous waste (Ref. 9.7).
 •   Factors affecting
     precipitation/coprecipitation performance -
     Items in the "Factors Affecting
     Precipitation/Coprecipitation Performance" box
     will also affect costs.
contaminants, arsenic precipitation/coprecipitation
processes may also cause other compounds to
precipitate, which can render the resulting sludge
hazardous (Ref. 9.7). The effluent may also require
further treatment, such as pH adjustment, prior to
discharge or reuse.                             L

More detailed information on selection and design of
arsenic treatment systems for small drinking water
systems is available in the document "Arsenic
Treatment Technology Design Manual for Small
Systems " (Ref. 9.36).

Summary of Cost Data

Limited cost data are currently available for
precipitation/coprecipitation treatment of arsenic.  At
the Winthrop Landfill Site (Project 1), groundwater
containing arsenic, 1,1-dichloroethane, and vinyl
chloride is being pumped and treated above ground
through a treatment train that includes precipitation.
The total capital cost of this treatment system was $2
million ($1.8 million for construction and $0.2 million
for design). O&M costs were about $350,000 per year
for the first few years and are now approximately
$250,000 per year.  The treatment system has a capacity
of 65 gpm. However, these costs are for the entire
treatment train (Ref. 9.29, cost year not provided). At
the power substation in Fort Walton, Florida, (Table
9.1, Project 4), the reported O&M cost was $0.006 per
gallon (for the entire treatment train, Ref 9.32, cost year
not provided). Capital cost information was not
provided.

A low-cost, point-of-use precipitation/coprecipitation
treatment designed for use in developing nations with
arsenic-contaminated drinking water was pilot-tested in
four areas of Bangladesh (Project 31). This simple
treatment process consists of a two-bucket system that
uses potassium permanganate and alum to precipitate
arsenic, followed by sedimentation and filtration.  The
equipment cost of the project was approximately $6,
and treatment of 40 liters of water daily would require a
monthly chemical cost of $0.20 (Ref. 9.22, cost year not
provided).

The document "Technologies and Costs for Removal of
Arsenic From Drinking Water" (Ref. 9.7) contains more
information on the cost of systems to treat arsenic in
drinking water to below the revised MCL of 0.010
mg/L. The document includes capital and O&M cost
curves for three precipitation/coprecipitation processes:

•    Enhanced coagulation/filtration
•    Enhanced lime softening
•    Coagulation assisted microfiltration

These cost curves are based on computer cost models
for drinking water treatment systems. Table 3.4 in
Section 3 of this document contains cost estimates
based on these curves for coagulation assisted
microfiltration.  The cost information available for
enhanced coagulation/ filtration and enhanced lime
softening are for retrofitting existing
precipitation/coprecipitation systems at
drinking water treatment plants to meet the revised
MCL. Therefore, the cost information could not be
used to estimate the cost of a new precipitation/
coprecipitation treatment system.

References

9.1    Federal Remediation Technologies Reference
       Guide and Screening Manual, Version 3.0.
       Federal Remediation Technologies Roundtable
       http://www.frtr.gov./matrix2/topjage.html
 9.2    Twidwell, L.G., et al.  Technologies and
       Potential Technologies for Removing Arsenic
       from Process and Mine Wastewater. Presented
       at "REWAS '99." San Sebastian, Spain.
       September 1999.
       http://www.mtech.edu/metallurgy/arsenic/
       REWASAS%20for%20proceedings99%20in%2
       Oword.pdf
                                                   9-4

-------
 9.3
 9.4
 9.5
 9.6
 9.7
9.8
9.9
9.10
9.11
9.12
9.13
9.14
 U.S. EPA. Final Best Demonstrated Available
 Technology (BDAT) Background Document; for
 K031, K084, K101, K102, Characteristic Arsenic
 Wastes (D004), Characteristic Selenium Wastes
 (DO 10), and P and U Wastes Containing Arsenic
 and Selenium Listing Constituents.  Office of
 Solid Waste. May 1990.
 U.S. EPA. Best Demonstrated Available   ;
 Technology (BDAT) Background Document for
 Wood Preserving Wastes:  F032, F034, and >
 F035; Final.  April, 1996. http://www.epa.gov/
 epaoswer/hazwaste/ldr/wood/bdat_bd.pdf   !
 U.S. EPA. Pump and Treat of Contaminated
 Groundwater at the Baird and McGuire     i
 Superfund Site, Holbrook, Massachusetts.   '
 Federal Remediation Technologies Roundtab'le.
 September, 1998.                        '
 http://www.frtr.gov/costperf.html.          .
 U.S. EPA. Development Document for Effluent
 Limitations Guidelines and Standards for the'
 Centralized Waste Treatment Industry.      ]
 December, 2000.                        I
 http://www.epa.gov/ost/guide/cwt/final/     i
 devtdoc.html                            !
 U.S. EPA. Technologies and Costs for Removal
 of Arsenic From Drinking Water.  EPA-R-00-
 028.  Office of Water. December, 2000.    '.
 http://www.epa.gov/safewater/ars/          !
 treatments_and_costs.pdf                 i
 U.S. EPA. Treatment Technologies for Site
 Cleanup: Annual Status Report (Tenth Edition).
 Office of Solid Waste and Emergency Response.
 EPA-542-R-01-004. February 2001.        i
 http://www.epa.gov/ncepi/Catalog/         l.
 EPA542R01004.html                     ]
 U.S. EPA National Risk Management Researph
 Laboratory. Treatability Database.         |
 U.S. EPA Technology Innovation Office.    j
 Database for EPA REACH IT (REmediation;
 And CHaracterization Innovative Technologies).
 http://www.epareachit.org.  March, 2001.    j
 Electric Power Research Institute.  Innovativb
 Technologies for Remediation of Arsenic in Soil
 Groundwater: Soil Flushing, In-Situ Fixation,!
 Iron Coprecipitation, and Ceramic Membrane|
 Filtration,  http://www.epri.com. 1996.      \
 U.S. EPA  Office of Research and Development.
 Contaminants and Remedial Options at Selected
 Metal-Contaminated Sites. EPA/540/R-95/51i2.
 July, 1995. http://search.epa.gov/s97is.vts    I
 U.S. EPA  Office of Solid Waste and Emergency
 Response. 1997 Biennial Reporting System ;
Database.                                i
U.S. EPA. Groundwater Remedies Selected at
 Superfund Sites. EPA 542-R-01-022. Januar^,
2002. http://clu-in.org                    j
 9.15  U.S. EPA. Groundwater Pump and Treat
       Systems: Summary of Selected Cost and
       Performance Information at Superfund-financed
       Sites.  EPA-542-R-01-021b. EPAOSWER.
       December 2001. http://clu-in.org
 9.16  MSB Technology Applications, Inc. Arsenic
       Oxidation Demonstration Project - Final Report.
       January 1998. http://www.arsenic.org/
       PDF%20Files/Mwtp-84.pdf
 9.17  Vendor information provided by MSB
       Technology Applications, Inc.
 9.18  HYDRO-Solutions and Purification. June 28,
       2001. http://www.mosquitonet.com/~hydro
 9.19  DPHE-Danida Arsenic Mitigation Pilot Project.
       June 28, 2001.
       http://phys4.harvard.edu/~wilson/
       2bucket.html.
 9.20  Environmental Research Institute. Arsenic
       Remediation Technology - AsRT. June 28,
       2001. http://www.eng2.uconn.edu/~nikos/
       asrt-brochure.html
 9.21  A Simple Household Device to Remove Arsenic
       from Groundwater Hence Making it Suitable for
       Drinking and Cooking.  June 28,2001
       http://phys4.harvard.edu/~wilson/
       asfilterl. html
 9.22  Appropriate Remediation Techniques for
       Arsenic-Contaminated Wells in Bangladesh.
       June 28, 2001. http://phys4.harvard.edu/
       -wilson/murcotthtml
 9.23   Redox Treatment of Groundwater to Remove
       Trace Arsenic at Point-of-Entry Water Treatment
       Systems. June 28, 2001
       http://phys4.harvard.edu/~wilson/Redox/
       Desc.html
 9.24   U.S. EPA Office of Water. Arsenic in Drinking
       Water. August 3, 2001. http://www.dainicb.i-
       consul.co.jp/english/arsenic/treatl.htm.
 9.25   U.S. EPA Office of Research and Development.
      Arsenic Removal from Drinking Water by
      Coagulation/Filtration and Lime Softening
      Plants. EPA/600/R-00/063.  June, 2000.
      http://www.epa.gov/ncepi/Catalog/
      EPA600R00063.html
 9.26  U.S. EPA and NSF International. ETV Joint
      Verification Statement for Chemical
      Coagulant/Filtration System Used in Packaged
      Drinking Water Treatment Systems. March,
      2001.
9.27  FAMU-FSU College of Engineering. Arsenic
      Remediation.  August 21,2001.
      http://www.eng.fsu.edu/departments/civil/
      research/arsenicremedia/index.htm
9.28   U.S. EPA. Contaminants and Remedial Options
      at Selected Metal-Contaminated Sites. Office of
      Research and Development.  EPA-540-R-95-
      512. July 1995.
                                                 9-5

-------
9.29  E-mail attachment sent from Anni Loughlin of
      U.S. EPA Region I to Linda Fiedler, U.S. EPA.
      August 21,2001.
9.30  U.S. EPA.  Arsenic & Mercury - Workshop on
      Removal, Recovery, Treatment, and Disposal.
      Office of Research and Development. EPA-600-
      R-92-105.  August 1992.
9.31  U.S. EPA.  Profiles of Metal Recovery
      Technologies for Mineral Processing and Other
      Metal-Bearing Hazardous Wastes. December
      1994.
9.32  Miller JP, Hartsfield TH, Corey AC, Markey
      RM.  In Situ Environmental Remediation of an
      Energized Substation. EPRI. Palo Alto, CA.
      Report No. 1005169.2001.
9.33  Robins, Robert G. Some Chemical Aspects
      Relating To Arsenic Remedial Technologies.
      Proceedings of the U.S. EPA Workshop on
      Managing Arsenic Risks to the Environment.
      Denver, Colorado. May 1-3, 2001.
9.34  E-mail from Bhupi Khona, U.S. EPA Region 3 to
      Sankalpa Nagaraja, Tetra Tech EM, Inc.,
      regarding Groundwater Pump-and-Treat of
      Arsenic at the Whitmoyer Laboratories
      Superfund site. May 3,2002.
9.35  Hydroglobe LLC. Removal of Arsenic from
      Bangladesh Well Water by the Stevens
      Technology for Arsenic Removal (S.T.A.R.).
      Hoboken, NJ. http://www.hydroglobe.net.
9.36  U.S. EPA. Arsenic Treatment Technology
      Design Manual for Small Systems (100% Draft
      for Peer Review). June 2002.
      http://www.epa.gov/safewater/smallsys/
      arsenicdesignmanualpeerreviewdraft.pdf
                                                 9-6

-------
                               Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic
Project
Number
Environi
1









Environi
3

4

5









Industry or Site
Type
Waste or
Media
Scale"
Site Name or
Location
Initial Arsenic
Concentration
Final Arsenic
Concentration
Precipitate
Arsenic
Concentration
Precipitating Agent
or Process0'
nental Media- Coagulation/Filtration "" 	
Landfill







Metal ore mining
andsmelting __

Groundwater







Surface water,
-LSpMOQ.-
gallons
Full







Full

Winthrop
Landfill
Superfund Site,
Winthrop, ME




Tex-Tin
^Superfund Site^
OU1,TX
0.300 mg/L







—


O.005 mg/L







—


—







-


Treatment train
consisting of pH
adjustment,
oxidation,
flocculation/
clarification, air
stripping, and sand-
bed filtration
Precipitation by pH
-adjustment followed
by filtration
nental Media - Iron Coprecipitation ' 	
Herbicide
application

Power substation

Chemical mixing









Groundwater

Groundwater,
44 million
gallons
Groundwater,
43,000 gpd








Full

Full

Full









"

Ft. Walton
Beach, FL

Baird and
McGuire
Superfund Site,
Holbrook, MA






0.005 - 3.8 mg/L

0.2- 1.0 mg/L

—









O.005 - 0.05
mg/L

O.005 mg/L

—









<5mg/L
(TCLP)

—

	









Iron coprecipitation
followed by
membrane filtration
Iron coprecipitation
followed by ceramic
membrane filtration
Treatment train
consisting of air
stripping,
precipitation (ferric
chloride, lime slurry,
phosphoric and
sulfuric acids, and
ammonium sulfate),
filtration, and carbon
adsorption.
Source

9.29







9.8


9.27

9.32

9.5,9.15









                                 9-7

-------
                                     Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)
Project
Number
6
7
8
9
10
Industry or Site
Type
Wood preserving
wastes
Metal ore mining
and smelting
activities
Herbicide
application
Metal ore mining
Metals
processing
Waste or ;
Media
Groundwater
Collection
pond water
Groundwater
Acid mine
water
Leachate from
nickel roaster
flue dust
disposal area
Scale"
Full
Pilot
Pilot
Pilot
Pilot
Site Name or
Location
Silver Bow
Creek/Butte
Area Superfund
Site - Rocker
Timber Framing
And Treatment
Plant OU,MT
Ryan Lode
Mine, AK

Susie
Mine/Valley
Forge site,
Rimini, MT
Susie
Mine/Valley
Forge site,
Rimini, MT
Initial Arsenic
Concentration

4.6mg/L
1 mg/L (TWA)
12.2 - 16.5 mg/L
423 - 439 mg/L
Final Arsenic
Concentration

0.027 mg/L
O.005 mg/L
(TWA)
0.017 - 0.053
mg/L
<0.32 mg/L
Precipitate
Arsenic
Concentration



8,830-13,300
mg/kg
0.0051-0.0076
mg/L (TCLP)
102,000 mg/kg
0.547-0.658
mg/L (TCLP)
Environmental Media - Other or Unspecified Precipitation Process
11
12
13
-
_
"
"Superfund
wastewater"
Groundwater
"Superfund
wastewater"
Full
Full
Full
—
-

0.1 - 1 mg/L
100 mg/L
0.1 - 1 mg/L
0.022 mg/L
< 0.2 mg/L
0.1 10 mg/L

—

Precipitating Agent
or Process0"
In situ treatment of
contaminated
groundwater by
injecting a solution
of ferrous iron,
limestone, and
potassium
permanganate
Enhanced iron co-
precipitation
followed by filtration
Iron coprecipitation
followed by ceramic
membrane filtration
Photo-oxidation of
arsenic followed by
iron coprecipitation
Photo-oxidation of
arsenic followed by
iron coprecipitation

Chemical
precipitation
Precipitation
Chemical
precipitation
Source
9.o
9.18
9.11
9.16
9.16


9.17

                                        9-8

-------
                                     Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)








Project
Number
14
15
16

17
18
19
Industry or Site
Type

Chemical
manufacturing
wastes,
groundwater
Chemical
manufacturing
Waste disposal
Wood preserving
Herbicide
manufacturing
Waste or
Media
Groundwater
Groundwater
Groundwater,
65,000 gpd
Groundwater,
43,000 gpd
Groundwater,
3,000 gpd
RCRA waste
codeK031,
1 mgd
Scale"
Full
Full
Full

Full
Full
Full
Site Name or
Location

Peterson/Puritan
Inc. Superfund
Site-GUI,
PAC Area, RI
Greenwood
Chemical
Superfund Site,
Greenwood, VA
Higgins Farm
Superfund Site,
Franklin
Township, NJ
Saunders Supply
Company
Superfund Site,
Chuckatuck, VA
Vineland
Chemical
Company
Superfund Site,
Vineland, NJ
Initial Arsenic
Concentration
lOOmg/L

__




Final Arsenic
Concentration
O.010 mg/L






Precipitate
Arsenic
Concentration







Precipitating Agent
or Process''
Reductive
Precipitation
(additional
information not
available)
In-situ treatment of
arsenic-contaminated
groundwater by
injecting oxygenated
water

consisting of metals
precipitation,
filtration, UV
oxidation and carbon
adsorption
Treatment train
consisting of air
stripping, metals
precipitation,
filtration, and ion
exchange
Treatment train
consisting of metals
precipitation,
filtration, and carbon
adsorption.
Metals precipitation
bllowed by filtration
Source
9.17
9.8
0 1*V

9.15
9.15
9.15
                                      9-9

-------
                                    Table 9.1
Arsenic Precipitation/Copredpitation Treatment Performance Data for Arsenic (continued)
Project
Number
20
Drinking
21
22
23
24
25
26
27
Industry or Site
Type
Veterinary feed
additives and
Pharmaceuticals
manufacturing
Waste or
Media
Groundwater,
50-100 gpm
Scale"
Full
Site Name or
Location
Whitmoyer
Laboratories
Superfund Site
Initial Arsenic
Concentration
100 mg/L
Final Arsenic
Concentration
0.025 mg/L
Precipitate
Arsenic
Concentration

Precipitating Agent
or Process0'
Neutralization and
flocculation by
increasing pH to 9
Water - Iron Coprecipitation

-




—
Drinking water,
1.6mgd
Drinking water,
1.4 mgd
Drinking water
Drinking water,
600 mgd
Drinking water,
62.5 mgd
Drinking water
Drinking water
Full
Full
Full
Full
Full
Full
Pilot

—
McGrath Road
Baptist Church,
AK



—
0.0203 mg/L
(TWA)
0.0485 mg/L
(TWA)
0.370 mg/L
0.0026 - 0.0121
mg/L
0.015 - 0.0239
mg/L
Plant A: 0.02
mg/L
Plant B: 0.049
mg/L
""_
0.0030 mg/L
(TWA)
0.01 13 mg/L
_(TWA)
<0.005 mg/L
0.0008 - 0.006
mg/L
0.0015-0.0118
mg/L
Plant A: 0.003
mg/L
Plant B: 0.012
mg/L
O.002 mg/L
Arsenic (V)
<5 mg/L (WET)
<5 mg/L (WET)

806-880 mg/kg
O.05-0.106
mg/L (TCLP)
293-493 mg/kg
0.058-0.114
mg/L (TCLP)


Feme
coprecipitation
followed by zeolite
softening
Ferric
coprecipitation
Enhanced iron co -
precipitation
followed by filtration
Ozonation followed
by coagulation with
iron- and aluminum-
based additives and
filtration
Coagulation with
iron and aluminum
based additives,
sedimentation, and
filtration
Adsorption and
coprecipitation with
iron hydroxide
precipitates
Iron coagulation
with direct filtration
Source
9.34

9.7
9.7
9.18
9.25
9.25
9.10
9.24
                                       9-10

-------
                                     Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)


Project
Number
28
Industry or Site
Type

Waste or
Media
Drinking water,
5.3 gallons
Scale8
Pilot
Site Name or
Location
Bhariab &
Sreenagar
Thana,
Bangladesh
Initial Arsenic
Concentration
0.28 - 0.59 mg/L
Final Arsenic
Concentration
O.03 - 0.05 mg/L
Precipitate
Arsenic
Concentration
1194mg/kg
Precipitating Agent
or Process0'
Iron co -
precipitation
followed by filtration
Source
9.35
Drinking Water - Lime Softening
29
30




Drinking water
Drinking water,
lOmgd

Full
Full

5 facilities,
identification
unknown



0.0159 - 0.0849
mg/L

O.003 mg/L
(TWA)
0.0063-0.0331
mg/L

<5 mg/L
(TCLP)
17.0-35.3 mg/kg
<0.05 mg/L
(TfT P~\

Lime softening at
pH>10.2
Oxidation followed
by lime softening
— ;and-filtration — '-
9.7
9.25
Drinking Water - Point-of-Use Systems
31
32
33



Drinking water
Drinking water
Drinking water,
40 liters per
day
Pilot
Pilot
Pilot
Harian Village
Rajshaji District
Bangladesh
West Bengal,
India
Noakhali,
Bangladesh
0.092-0.120
mg/L
0.300 mg/L
0.12 -0.46 mg/L
0.023 - 0.036
mg/L
0.030 mg/L
O.05 mg/L



Naturally-occurring
iron at 9 mg/L
facilitates
precipitation,
followed by
sedimentation,
filtration and
acidification
Precipitation with
sodium hypochlorite
and alum, followed
by mixing,
flocculation,
sedimentation, and
up-flow filtration
Coagulation with
potassium
permanganate and
alum, followed by
sedimentation and
filtration
9.22
9.22
9.19
                                      9-11

-------
I
                                                                              Table 9.1
                                         Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)
Project
Number
34
35
Industry or Site
Type


Waste or
Media
Drinking water,
1.0-1.1 gpm
Drinking water,
20 liters per
day
Scale"
Pilot
Pilot
Site Name or
Location
Spiro Tunnel
Water Filtration
Plant, Park City,
UT
West Bengal,
India
Initial Arsenic
Concentration
0.0609-0.146
mg/L

Final Arsenic
Concentration
0.0012 - 0.0345
mg/L

Precipitate
Arsenic
Concentration


Precipitating Agent
or Process"'
Precipitation with
ferric chloride and
sodium hypochlorite,
followed by filtration
Precipitation by
ferric salt, oxidizing
agent, and activated
charcoal, followed
by sedimentation and
filtration
Source
9.26
9.21
Wastewaters - Lime Softening
36
37
38
39
Veterinary
Pharmaceuticals



K084,
wastewater
Wastewater
Wastewater
Wastewater
Full
Full
Full
Full
Charles City,
Iowa


BP Minerals
America
399- 1,670 mg/L
(TWA)
4.2 mg/L (TWA)
4.2 mg/L (TWA)

Calcium arsenate,
60.5 - 500 mg/L
(TWA)
0.51 mg/L (TWA)
0.34 mg/L (TWA)

45,200 mg/kg
(TWA) 2,200
mg/L (TCLP)


Calcium
arsenate and
calcium arsenite,
1,900 - 6,900
mg/kg (TWA)
0.2 - 74.5 mg/L
(EP Tox)
Calcium hydroxide
Lime precipitation
followed by
sedimentation
Lime precipitation
followed by
sedimentation and
filtration
Lime
9.3
9.4
9.4
9.3
                                                                                9-12

-------
                                     Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)


Project
Number
Industry or Site
Type
Waste or
Media
Scale2
Site Name or
Location
Initial Arsenic
Concentration
Final Arsenic
Concentration
Precipitate
Arsenic
Concentration
Precipitating Agent
or Process1'
Source
Wastewaters - Metal Sulfates
40
41

42
Veterinary
Pharmaceuticals
Metals
processing

Metals
processing
K084,
wastewater
Spent leachate
from the
recovery of Cu,
Ag, and Sb
from ores
(amount not
available)
Leachate from
filter cake from
purification of
zinc sulfate
electrowinning
solution
(amount not
available)
Full
Full

Full
Charles City,
Iowa
Equity Silver
Mine, Houston,
British
Columbia,
Canada

Texasgulf
Canada,
Timmons,
Ontario, Canada
125 - 302 mg/L
(TWA)



Manganese
arsenate, 6.02 -
22.4 mg/L (TWA)



47,400 mg/kg
(TWA) 984
mg/L (TCLP)
95 to 98%
recovery of
arsenic

98% recovery of
arsenic
Manganese sulfate
Acid addition,
chemical
precipitation with
copper sulfate, and
filtration

Acid addition,
chemical
precipitation with
copper sulfate, and
filtration
9.3
9.30

9.30
Wastewaters - Iron Coprecipitation
43
44

Veterinary
Pharmaceuticals
Wastewater
from wet
scrubbing of
incinerator vent
gas (D004,
P011)
K084,
wastewater
Full
Full
American
NuKem
Charles City,
Iowa
69.6 - 83.7 mg/L
(TWA)
15 - 107 mg/L
(TWA)
O.02 - 0.6 mg/L
(TWA)
Ferric arsenate,
0.163-0.580
mg/L (TWA)

9,760 mg/kg
(TWA)
0.508 mg/L
(TCLP)
Chemical oxidation
followed by
precipitation with
ferric salts
Ferric sulfate
9.3
9.3
                                      9-13

-------
                                     Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)
Project
Number
Industry or Site
Type
Waste or
Media
Scale'
i Site Name or
Location
Initial Arsenic
Concentration
Final Arsenic
Concentration
Precipitate
Arsenic
Concentration
Precipitating Agent
or Process"
Source
Wastewaters - Other or Unspecified Precipitation Process
45
46
47
48
49

Centralized waste
treatment
industry
Centralized waste
treatment
industry
Centralized waste
treatment
industry
Centralized waste
treatment
industry
Wastewater
Wastewater
Wastewater
Wastewater
Wastewater
Full
Full
Full
Full
Full





<0.1-3.0mg/L
(TWA)
57 mg/L (TWA)
57 mg/L (TWA)
57 mg/L (TWA)
57 mg/L (TWA)
0.18 mg/L
(average, TWA)
0.181 mg/L
(TWA)
0.246 mg/L
(TWA)
0.084 mg/L
(TWA)
0.0 11 mg/L
(TWA)





Chemical reduction
followed by
precipitation,
sedimentation, and
filtration
Primary precipitation
with solids-liquid
separation
Primary precipitation
with solids-liquid
separation followed
by secondary
precipitation with
solids-liquid
separation
Primary precipitation
with solids-liquid
separation followed
by secondary
precipitation with
solids-liquid
separation and
multimedia filtration
Selective metals
precipitation, solids-
liquid separation,
secondary
precipitation, solids-
liquid separation,
tertiary precipitation,
and solid-liquid
separation
9.4
9.6
9.6
9.6
9.6
                                       9-14

-------
                                     Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)
Project
Number
50
51
52
53
54
55
56
57
58
Industry or Site
Type
Chemical and
allied products
—
Transportation
equipment
industry
Chemicals and
allied products
WR Metals
-^jJndustries 	
(WRMI) arsenic
leaching process
Metals
processing
Metals
processing
Metallurgie-
Hoboken-
Overpelt (MHO)
solvent extraction
process
Metals
processing
Electric, gas, and
sanitary
Primary metals
Waste or
Media
Wastewater
Domestic
wastewater
Wastewater
Wastewater
Leachate from
. arsenical Hue,-
dusts from non-
ferrous
smelters
(amount not
available)
Spent leachate
from the
recovery of Ag
from ores
(amount not
available)
Spent
electrolyte
fromCu
refining
(amount not
available)
Wastewater
Wastewater
Scale8
Full
Full
Full
Full
Full
Full
Full
Pilot
Pilot
Site Name or
Location
—
—

—
WR Metals
-_ -Jndustries 	
(location not
available)
Sheritt Gordon
Mines, LTD.,
Fort
Saskatchewan,
Alberta, Canada
Olen, Belgium
—
~
Initial Arsenic
Concentration
Ob- - 0.1 mg/L
(TWA)
Ob'- 0.1 mg/L
(TWA)
0.1-1 mg/L
(TWA)
0.1 - 1 mg/L
(TWA)
110,000-550,000
-mg/k&(TWA)-^


Ob- - 0.1 mg/L
(TWA)
Ob-- 0.1 mg/L
(TWA)
Final Arsenic
Concentration
0.0063 mg/L
(TWA)
0.0015 mg/L
(TWA)
O.002 mg/L
(TWA)
0.028 mg/L
(TWA)



0.0028 mg/L
(TWA)
O.0015 mg/L
(TWA)
Precipitate
Arsenic
Concentration
—
—

—


99.96%
recovery of
arsenic
—
--
Precipitating Agent
or Process0'
Chemically assisted
clarification
Chemical
precipitation
Chemical
precipitation and
filtration
Chemically assisted
clarification
Chemical
— precipitation and -
filtration
Chemical
precipitation and
filtration
Chemical
precipitation and
filtration
Chemically assisted
clarification
Chemical
precipitation
Source
9.9
9.9
9.9
9.9
9.31
9.30
9.31
9.9
9.9
                                      9-15

-------
                                    Table 9.1
Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)
Project i
Number
59
60
61
62
63
64
65
Industry or Site
Type

—



Landfill

Waste or
Media
Wastewater
bearing
unspecified
RCRA listed
waste code
Domestic
wastewater
Wastewater
bearing
unspecified
RCRA listed
waste code
Wastewater
bearing
unspecified
RCRA listed
waste code
Wastewater
bearing
unspecified
RCRA listed
waste code
Hazardous
leachate, F039
Wastewater
bearing
unspecified
RCRA listed
waste code
Scale"
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Site Name or
Location

—





Initial Arsenic
Concentration
Ob--0.1mg/L
(TWA)
Ob-- 0.1 mg/L
(TWA)
0.1 - 1 mg/L
(TWA)
0.1 - 1 mg/L
(TWA)
0.1 - 1 mg/L
(TWA)
0.1 - 1 mg/L
(TWA)
0.1 - 1 mg/L
(TWA)
Final Arsenic
Concentration
0.001 mg/L
(TWA)
0.001 mg/L
(TWA)
0.012 mg/L
(TWA)
0.012 mg/L
(TWA)
0.006 mg/L
(TWA)
0.008 mg/L
(TWA)
0.0 14 mg/L
(TWA)
Precipitate
; Arsenic
Concentration

"~





Precipitating Agent
or Process''
Chemical
precipitation,
activated carbon
adsorption, and
filtration
Chemical
precipitation
Chemical
precipitation,
activated carbon
adsorption, and
filtration
Chemical
precipitation,
activated carbon
adsorption, and
filtration
Chemical
precipitation,
activated carbon
adsorption, and
filtration
Chemical
precipitation,
activated carbon
adsorption, and
filtration
Chemical
precipitation,
activated carbon
adsorption, and
filtration
Source
9.9
9.9
9.9
9.9
9.9
9.9
9.9
                                      9-16

-------
                                                                    Table 9.1
                             Arsenic Precipitation/Coprecipitation Treatment Performance Data for Arsenic (continued)
Project
Number
66
67
68

69
Industry or Site
Type
Municipal
landfill
Metals
processing
Metals
processing

Waste or
Media
Leachate
Scrubber water
from lead
smelter
Thickener
overflow from
lead smelter
Industrial
wastewater
Scale"
Pilot
Pilot
Pilot

Pilot
Site Name or
Location


—


Initial Arsenic
Concentration
1 - 10 mg/L
(TWA)
3,300 mg/L
5.8 mg/L

5.8mg/kg
Final Arsenic
Concentration
8 mg/L (TWA)
0.007 mg/L
0.003 mg/L

< 0.5 mg/kg
Precipitate
Arsenic
Concentration


—


Precipitating Agent
or Process0'
Chemical
precipitation,
activated carbon
adsorption, and
filtration
Mineral-like
precipitation
(additional
information not
available)
Mineral-like
precipitation
(additional
information not
available)

Source
9.9
9.17
9.17

9.17
a  Excluding bench-scale treatments.
b  Detection limit not provided.
c  The information that appears in the "Precipitating Agent or Process" column, including the chemicals used, the descriptions of the precipitation/
   coprecipitation processes, and whether the process involved precipitation or coprecipitation, were prepared based on the information reported in the cited
   references. This information was not independently checked for accuracy or technical feasability.  In some cases the term "precipitation" may be applied to a
   process that is actually coprecipitation.
EPT = Extraction procedure toxicity test
mg/L = milligrams per liter
RCRA = Resource Conservation and Recovery Act
WET = Waste extraction test
mg/kg = milligrams per kilogram
—  = Not available
TWA = Total waste analysis
gpd = gallons per day
mgd = million gallons per day
TCLP = Toxicity characteristic leaching
procedure
                                                                      9-17

-------

-------
 10.0    MEMBRANE FILTRATION FOR
         ARSENIC
  Summary

   Membrane filtration can remove a wide range of1
  contaminants from water. Based on the information
  collected to prepare this report, this technology  .
  typically can reduce arsenic concentrations to less
  than 0.050 mg/L and in some cases has reduced
  arsenic concentrations to below 0.010 mg/L.
  However, its effectiveness is sensitive to a variety of
  untreated water contaminants and characteristics. It
  also produces a larger volume of residuals and tends
  to be more expensive than other arsenic treatment'
  technologies. Therefore, it is used less frequently
  than precipitation/coprecipitation, adsorption, and
  ion exchange.  It is most commonly used to treat
  groundwater and drinking water, or as a polishing
  step for precipitation processes. Only two full-scale
  projects using membrane filtration to treat arsenic1
  were identified in the sources researched for this
  report.
Technology Description and Principles         I

There are four types of membrane processes:      I
microfiltration (MF), ultrafiltration (UF), nanofiltratjion
(NF), and reverse osmosis (RO). All four of these !
processes are pressure-driven and are categorized by the
size of the particles that can pass through the      !
membranes or by the molecular weight cut off (i.e., j
pore size) of the membrane (Ref. 10.2). The force !
 Technology Description:  Membrane filtration
 separates contaminants from water by passing it
 through a semi-permeable barrier or membrane.
 The membrane allows some constituents to pass
 through, while blocking others (Ref. 10.2,10.3).

 Media Treated:

 •   Drinking water
 •   Groundwater
 •   Surface water
     Industrial wastewater

 Types of Membrane Processes:

     Microfiltration
 •   Ultrafiltration
     Nanofiltration
 •   Reverse osmosis
 required to drive fluid across the membrane depends on
 the pore size; NF and RO require a relatively high
 pressure (50 to 150 pounds per square inch [psi]), while
 MF and UF require lower pressure (5 to 100 psi) (Ref.
 10.4).  The low pressure processes primarily remove
 contaminants through physical sieving, and the high
 pressure processes through chemical diffusion across
 the permeable membrane (Ref. 10.4).

       Model of a Membrane Filtration System
   Contaminated
       Water
 Because arsenic species dissolved in water tend to have
 relatively low molecular weights, only NF and RO
 membrane processes are likely to effectively treat
 dissolved arsenic (Ref. 10.4).  MF has been used with
 precipitation/coprecipitation to remove solids
 containing arsenic. The sources used for this report did
 not contain any information on the use of UF to remove
 arsenic; therefore, UF  is not discussed in this
 technology summary.  MF generates two treatment
 residuals from the influent waste stream: a treated
 effluent (permeate) and a rejected waste stream of
 concentrated contaminants (reject).

 RO is a high pressure process that primarily removes
 smaller ions typically associated with total dissolved
 solids. The molecular  weight cut off for RO
 membranes ranges from 1 to 20,000, which is a
 significantly lower cut off than for NF membranes. The
 molecular weight cut off for NF membranes ranges
 from approximately 150 to 20,000. NF is a high-
pressure process that primarily removes larger divalent
 ions associated with hardness (for example, calcium
 [Ca], and magnesium [Mg] but not monovalent salts
(for example, sodium [Na] and chlorine [Cl]). NF is
slightly less efficient than RO in removing  dissolved
arsenic from water (Ref. 10.4).
                                                  10-1

-------
MF is a low-pressure process that primarily removes
particles with a molecular weight above 50,000 or :a
particle size greater than 0.050 micrometers. The pore
size of MF membranes is too large to effectively
remove dissolved arsenic species, but MF can remove
particulates containing arsenic and solids produced by
precipitation/coprecipitation (Ref. 10.4).

Media and Contaminants Treated

Drinking water, surface water, groundwater, and
industrial wastewater can be treated with this
technology. Membrane filtration can treat dissolved
salts and other dissolved materials (Ref. 10.12).

Type* Number, and Scale of Identified Projects
Treating Water Containing Arsenic

The data gathered for this report identified one full-
scale RO and one full-scale MF treatment of arsenic in
groundwater and surface water (Figure 10.1). The MF
application is a treatment train consisting of
precipitation/coprecipitation followed by MF to remove
solids. In addition, 16 pilot-scale and three bench-scale
applications of RO and eight pilot-scale and three
bench-scale applications of NF have been identified.
One pilot-scale application of MF to remove solids
from precipitation/coprecipitation of arsenic has also
been identified.

                     Figure 10.1
 Scale of Identified Membrane Filtration Projects for
                 Arsenic Treatment
   Full
   Pilot
 Bench
 Summary of Performance Data

 Table 10.1 presents the performance data found for this
 technology.  Performance results for membrane
 filtration are typically reported as percent removal, (i.e.,
 the percentage of arsenic, by mass, in the influent that is
 removed or rejected from the influent wastewater
 stream).  A higher percentage indicates greater removal
 of arsenic, and therefore, more effective treatment.
 Factors Affecting Membrane Filtration
 Performance

 •   Suspended solids, high molecular weight,
     dissolved solids, organic compounds, and
     colloids - The presence of these constituents in
     the feed stream may cause membrane fouling.
     Oxidation state of arsenic - Prior oxidation of
     the influent stream to convert As(III) to As(V)
     will increase arsenic removal; As(V) is
     generally larger and is captured by the
     membrane more effectively than As(III).
     pH - pH may affect the adsorption of arsenic on
     the membrane by creating an electrostatic
     charge on the membrane surface.
 •   Temperature - Low influent stream
     temperatures decreases membrane flux.
     Increasing system pressure or increasing the
     membrane surface area may compensate for low
     influent stream temperature.
Although many of the projects listed in Table 10.1 may
have reduced arsenic concentrations to below 0.05
mg/L or 0.01 mg/L, data on the concentration of arsenic
in the effluent and reject streams were not available for
most projects.

For two RO projects, the arsenic concentration in the
reject stream was available, allowing the concentration
in permeate to be calculated.  For both projects, the
concentration of arsenic prior to treatment was greater
than 0.050 mg/L, and was reduced to less than 0.010
mg/L in the treated water.

For two projects involving removal of solids from
precipitation/coprecipitation treatment of arsenic with
MF, the arsenic concentration in the permeate was
available. The concentration prior to precipitation/
coprecipitation treatment was greater than 0.0^0 mg/L
for one project, and ranged from 0.005 to 3.8 mg/L for
the other.  For both projects, the concentration in the
treated water was less than 0.005 mg/L.

The case study at the end of this section further
discusses  the use of membrane filtration to remove
arsenic from groundwater used as a drinking water
source. Information for this site is summarized in Table
 10.1, Project 31.
                                                    10-2

-------
Applicability, Advantages, and Potential
Limitations                                  !

Membrane technologies are capable of removing ajwide
range of dissolved contaminants and suspended solids
from water (Ref. 10.12).  RO and NF technologies j
require no chemical addition to ensure adequate   '
separation. This type of treatment may be run in either
batch or continuous mode. This technology's    j
effectiveness is sensitive to a variety of contaminants
and characteristics in the untreated water. Suspended
solids, organics, colloids, and other contaminants can
cause membrane fouling.  Therefore, it is typically:
applied to groundwater and drinking water, which are
less likely to contain fouling contaminants. It is also
applied to remove solids  from precipitation processes
and as a polishing step for other water treatment
technologies when lower concentrations must be
achieved.
More detailed information on selection and design
arsenic treatment systems for small drinking water
systems is available in the document "Arsenic
Treatment Technology Design Manual for Small
Systems" (Ref. 10.15).
bf
  Factors Affecting Membrane Filtration Costs

  •   Type of membrane filtration - The type of
      membrane selected may affect the cost of the
      treatment (Ref. 10.1, 10.2).                :
  •   Initial waste stream - Certain waste streams
      may require pretreatment, which would
      increase costs (Ref. 10.4).
  •   Rejected waste stream - Based on
      concentrations of the removed contaminant,  :
      further treatment may be required prior to
      disposal or discharge (Ref. 10.4).
  •   Factors affecting membrane filtration     ;
      performance - Items in the "Factors Affecting
      Membrane Filtration Performance" box will  i
      also affect costs.                          ;
Summary of Cost Data                       I

The research conducted in support of this report did not
document any cost data for specific membrane filtration
projects to treat of arsenic.  The document        :
"Technologies and Costs for Removal of Arsenic From
Drinking Water" (Ref. 10.4) contains additional
information on the cost of point-of-use reverse osmbsis
systems to treat arsenic in drinking water to levels |
below the revised MCL of 0.010 mg/L. The docunient
          Case Study:  Park City Spiro Tunnel Water
          Filtration Plant

          The Park City Spiro Tunnel Water Filtration Plant in
          Park City, Utah treats groundwater from water-
          bearing fissures that collect in a tunnel of an
          abandoned silver mine to generate drinking water.
          A pilot-scale RO unit treated contaminated water at
          a flow rate of 0.77 gallons per minute (gpm) from
          the Spiro tunnel for 34 days. The total and
          dissolved arsenic in the feedwater averaged 0.065
          and 0.042 mg/L, respectively.  The total and
          dissolved arsenic concentrations in the permeate
          averaged <0.0005 and O.0008 mg/L, respectively.
          The RO process reduced As (V) from 0.035 to
          0.0005 mg/L and As (III) from 0.007 to 0.0005
          mg/L.  The membrane achieved 99% total As
          removal and 98% As (V) removal (Ref. 10.12) (see
          Project 31, Table 10.1).
         includes capital and O&M cost curves for this
         technology. These cost curves are based on computer
         cost models for drinking water treatment systems.

         References

         10.1   U.S. EPA Office of Research and Development.
               Arsenic & Mercury - Workshop on Removal,
               Recovery, Treatment, and Disposal. EPA-600-
               R-92-105. August 1992.
         10.2   U.S. EPA Office of Research and Development.
               Regulations on the Disposal of Arsenic
               Residuals from Drinking Water Treatment
               Plants. Office of Research and Development.
               EPA-600-R-00-025. May 2000.
               http://www.epa.gov/ORD/WebPubs/
               residuals/index.htm
         10.3   U.S. EPA Office of Solid Waste.  BOAT
               Background Document for Spent Potliners from
               Primary Aluminum Reduction - K088. EPA
               530-R-96-015. February 1996.
               http://www.epa.gov/ncepi/Catalog/
               EPA530R96015.html
         10.4   U.S. EPA Office of Water. Technologies and
               Cost for Removal of Arsenic from Drinking
               Water. EPA 815-R-00-028. December 2000.
               http://www.epa.gov/safewater/ars/
               treatments_and_costs.pdf
         10.5   U.S. EPA National Risk Management Research
               Laboratory.  Treatability Database. March 2001.
                                                  10-3

-------
10.6  U.S. Technology Innovation Office. Database
      for EPA REACH IT (REmediation And
      CHaracterization Innovative Technologies).
      http://www.epareachit.org.  March 2001.
 10.7  U.S. EPA Office of Research and Development.
      Contaminants and Remedial Options at Selected
      Metal-Contaminated Sites.  EPA/540/R-95/512.
      July, 1995. http://search.epa.gov/s97is.vts
10.8  Federal Remediation Technologies Reference
      Guide and Screening Manual, Version 4.0. ,
      Federal Remediation Technologies Roundtable.
      Septembers, 2001.
      http://www.fhr.gov/matrix2/top_page.html.
10.9  U.S. EPA Office of Water.  Arsenic in Drinking
      Water Rule Economic Analysis. EPA 815-R-OO-
      026.  December 2000.
      http://www.epa.gov/safewater/ars/
      econ_analysis.pdf
10.10 Code of Federal Regulations, Part 40, Section
      268.  Land Disposal Restrictions.
      http://lula.law.cornell.edu/cfr/
      cfr.php?title=40&type=part&value=268
10.11 Code of Federal Regulations, Part 400. Effluent
      Limitations Guidelines.
      http://www.epa.gov/docs/epacfr40/chapt-I.info/
      subch-N.htm
10.12 Environmental Technology Verification Program
      (ETV). Reverse Osmosis Membrane Filtration
      Used In Packaged Drinking Water Treatment
      Systems,  http://www.membranes.com. March
      2001.
10.13 Electric Power Research Institute. Innovative
      Technologies for Remediation of Arsenic in Soil
      Groundwater: Soil Flushing, In-Situ Fixation,
      Iron Coprecipitation, and Ceramic Membrane
      Filtration, http://www.epri.com. April 2000.
10.14 FAMU-FSU College of Engineering. Arsenic
      Remediation.
      http://www.eng.fsu.edu/departments/civil/
      research/arsenicremedia/index.htm August 21,
      2001.
10.15 U.S. EPA. Arsenic Treatment Technology
      Design Manual for Small Systems (100% Draft
      for Peer Review).  June 2002.
      http://www.epa.gov/safewater/smallsys/
      arsenicdesignmanualpeerreviewdraft.pdf
                                                  10-4

-------
                       Table 10.1
Membrane Filtration Treatment Performance Data for Arsenic
rroject
Number
Media or Waste
Scale
Site Name or
Location
Initial Arsenic
Concentration
Percent Arsenic Removal" or
Final Arsenic Concentration
Membrane or
Treatment Process
Source
Nanofiltration " 	 — ' 	
1
2
3
4
5

6
7
o
9
10
11
Groundwater
Groundwater
Groundwater with low
DOC (Img/L)
Groundwater with high
DOC(llmg/L)
Groundwater with high
DOC(llmg/L)

Arsenic spiked surface
water
Arsenic spiked surface
water
Arsenic spiked surface
water
Arsenic spiked DI water
Arsenic spiked lake
water
Arsenic spiked DI water
Pilot
Pilot
Pilot
Pilot
Pilot

Pilot
Pilot
Pilot
Bench
Bench
Bench
Tarrytown, NY
Tarrytown, NY


"


~




0.038-0. 154 mg/L
0.038- 0.154 mg/L


—


__
**~


"
95%
95%
60%
80%
75% initial,
3-16% final

Arsenic (III) 20%
Arsenic (V) > 95%
Arsenic (III) 30%
Arsenic (V) > 95%
Arsenic (III) 52%
Arsenic (V) > 95%
Arsenic (III) 12%
Arsenic (V) 85%
Arsenic (V) 89%
Arsenic (V) 90%
—
—
Single element,
negatively charged
membrane
Single element,
negatively charged
membrane
Single element,
negatively charged
membrane
Single element
membrane
Single element
membrane
Single element
membrane
Single element,
negatively charged
membrane
Single element,
negatively charged
membrane
Flat sheet, negatively
charged membrane
10.4
10.4
10.4
10.4
10.4

10.4
10.4
10.4
10.4
10.4
10.4


                         10-5

-------
                            Table 10.1
Membrane Filtration Treatment Performance Data for Arsenic (continued)
Project
Number
Media or Waste
Scale
Site Name or
Location
Initial Arsenic
Concentration
Percent Arsenic Removal* or
Final Arsenic Concentration
Membrane or
Treatment Process
Reverse Osmosis
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Surface water
contaminated with wood
preserving wastes
Groundwater
Groundwater
Groundwater
Groundwater
Groundwater
Groundwater with low
DOC
Groundwater with high
DOC
Arsenic spiked surface
water
Arsenic spiked surface
water
Arsenic spiked surface
water
Arsenic spiked surface
water
Groundwater
Groundwater
Groundwater
Full
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot
Pilot

Charlotte Harbor, FL
Cincinnati, OH
Eugene, OR
Fairbanks, AL
Hudson, NH


—
—
--

San Ysidro, NM
San Ysidro, NM
San Ysidro, NM
24.4 mg/L
—
-
-
-
- -


~~
~~
—

-
—
"
Arsenic removal, 99%
reject stream, 57.7 mg/L
treated effluent stream, 0.0394
mg/L
Arsenic (III) 46-84%
Arsenic (V) 96-99%
Arsenic (III) 73%
50%
50%
40%
> 80%
> 90%
Arsenic (III) 60%
Arsenic (V) > 95%
Arsenic (III) 68%
Arsenic (V) > 95%
Arsenic (III) 75%
Arsenic (V) > 95%
Arsenic (III) 85%
Arsenic (V) > 95%
91%
99%
93-99%
Treatment tram
consisting of RO
followed by ion
exchange. Performance
data are for RO treatment
only.

—
—
—
—
Single element,
negatively charged
membrane
Single element,
negatively charged
membrane
Single element
membrane
Single element
membrane
Single element
membrane
Single element
membrane
—
Hollow fiber, polyamide
membrane
Hollow fiber, cellulose
acetate membrane
Source

10.1
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.4
10.4
                                10-6

-------
                                                                   Table 10.1
                                    Membrane Filtration Treatment Performance Data for Arsenic (continued)
rroject
Number
27
28
29
30
31
Media or Waste
Groundwater
Arsenic spiked lake
water
Arsenic spiked DI water
Arsenic spiked DI water
Drinking water
Scale
Pilot
Bench
Bench
Bench
Pilot
Site Name or
Location
Tarrytown, NY
"
"
-
Park City Spiro
Tunnel Water
Filtration Plant, Park
City, Utah
Initial Arsenic
Concentration
-
__
.,„
-
0.065 mg/L
Percent Arsenic Removal" or
Final Arsenic Concentration
86%
Arsenic (III) 5%
Arsenic (V) 96%
Arsenic (HI) 5%
Arsenic (V) 96%
Arsenic (V) 88%
0.0005 mg/L
Membrane or
Treatment Process
--
—
—
—

Source
10.4
10.4
10.4
10.4
10.12
MicroliltrationT ~" ' 	 ' 	
32
33
Groundwater
Groundwater
Full
Pilot


0.005 - 3.8 mg/L
0.2 -1.0 mg/L
O.005 - 0.05 mg/L
O.005 mg/L
Iron coprecipitation
followed by membrane
filtration
Iron coprecipitation
followed by ceramic
membrane filtration
10.14
10.13
a  Percent arsenic rejection is 1 minus the mass of arsenic in the treated water divided by the mass of arsenic in the influent times 100
   [(l-(mass of arsenic influent/mass of arsenic effluent))* 100].
DI = Deionized
DOC = Dissolved organic carbon
- = Not available
NF = Nanofiltration
RO = Reverse Osmosis
                                                                     10-7

-------

-------
11.0 ADSORPTION TREATMENT FOR     [
ARSENIC                                    j
                                              i
Technology Description and Principles         ,
                                              i
This section discusses arsenic removal processes that
use a fixed bed of media through which water is passed.
Some of the processes described in this section rely on a
combination of adsorption, precipitation/
coprecipitation, ion exchange, and filtration. However,
the primary removal mechanism in each process is!
adsorption. For example, greensand is made from'
glauconite, a green, iron-rich, clay-like mineral th4t
usually occurs as small pellets mixed with other sand
particles.  The glauconite-containing sand is treateji
with potassium permanganate (KMnO4), forming 4
layer of manganese oxides on the sand. As water ;
passes through a greensand filtration bed, the KMnO4
oxidizes As(III) to  As(V), and As(V) adsorbs onto:the
greensand surface.  In addition, arsenic is removedi by
ion exchange, displacing species from the manganese
oxide (presumably hydroxide ion [OH"] and water!
[H2O]). When the  KMnO4 is exhausted, the greensand
media must be regenerated or replaced. Greensand
media is regenerated with a solution of excess KMnO4.
Greensand filtration is also known as
oxidation/filtration (Ref. 11.3).                  ;
  Summary

  Adsorption has been used to treat groundwater and
  drinking water containing arsenic. Based on the
  information collected for this report, this technology
  typically can reduce arsenic concentrations to less
  than 0.050 mg/L and in some cases has reduced
  arsenic concentrations to below 0.010 mg/L. Its •
  effectiveness is sensitive to a variety of untreated^
  water contaminants and characteristics. It is used
  less frequently than precipitation/coprecipitation,
  and is most commonly used to treat groundwater and
  drinking water, or as a polishing step for other water
  treatment processes.                          ;
Activated alumina (AA) is the sorbent most commbnly
used to remove arsenic from drinking water (Ref. 11.1),
and has also been used for groundwater (Ref. 11.4).
The reported adsorption capacity of AA ranges from
0.003 to 0.112 grams of arsenic per gram of AA (Ref.
11.4). It is available in different mesh sizes and its
particle size affects contaminant removal efficiency.
                                              i
Up to 23,400 bed volumes of wastewater can be treated
before AA requires regeneration or disposal and   !
           Model of an Adsorption System
   Contaminated
     Water
        Sorbent
                                         Effluent
replacement with new media (Ref. 11.3). Regeneration
is a four-step process:

• Backwashing
• Regeneration
• Neutralization
• Rinsing
  Technology Description: In adsorption, solutes
  (contaminants) concentrate at the surface of a
  sorbent, thereby reducing their concentration hi the
  bulk liquid phase. The adsorption media is usually
  packed into a column. As contaminated water is
  passed through the column, contaminants are
  adsorbed.  When adsorption sites become filled, the
  column must be regenerated or disposed of and
  replaced with new media.

  Media Treated:
  •    Groundwater
  *    Drinking water

  Types of Sorbent Used in Adsorption to Treat
  Arsenic:
  •    Activated alumina (AA)
  •    Activated carbon (AC)
  •    Copper-zinc granules
  •    Granular ferric hydroxide, ferric hydroxide-
      coated newspaper pulp, iron oxide coated sand,
      iron filings mixed with sand
  •    Greensand filtration (KMnO4 coated glauconite)
  •    Proprietary media
  •    Surfactant-modified zeolite
                                                  11-1

-------
The regeneration process desorbs the arsenic. The
regeneration fluid most commonly used for AA
treatment systems is a solution of sodium hydroxide.
The most commonly used neutralization fluid is a
solution of sulfuric acid. The regeneration and
neutralization steps for AA adsorption systems might
produce a sludge because the alumina can be dissolved
by the strong acids and bases used in these processes,
forming an aluminum hydroxide precipitate in the spent
regeneration and neutralization fluids. This sludge
typically contains a high concentration of arsenic (Ref.
11.1).

Activated carbon (AC) is an organic sorbent that is
commonly used to remove organic and metal
contaminants from drinking water, groundwater, arid
wastewater (Ref. 11.4). AC media are normally
regenerated using thermal techniques to desorb and
volatilize contaminants (Ref. 11.6).  However,
regeneration of AC media used for the removal of :
arsenic from water might not be feasible (Ref. 11.4).
The arsenic might not volatilize at the temperatures
typically used in AC regeneration. In addition, off-gas
containing arsenic from the regeneration process may
be difficult or expensive to manage.

The reported adsorption capacity of AC is 0.020 grams
of As(V) per gram of AC. As(HI) is not effectively
removed by AC. AC impregnated with metals such as
copper and ferrous iron has a higher reported adsorption
capacity for arsenic.  The reported adsorption capacity
for As(III) is 0.048 grams per gram of copper-
impregnated carbon and for As(V) is 0.2 grams per
gram of ferrous iron-impregnated carbon (Ref. 11.4).

Iron-based adsorption media include granular ferric
hydroxide, ferric hydroxide-coated newspaper pulp?
ferric oxide, iron oxide-coated sand, sulfur-modified
iron, and iron filings mixed with sand.  These media
have been used primarily to remove arsenic from
drinking water. Processes that use these media
typically remove arsenic using adsorption in
combination with oxidation, precipitation/
coprecipitation, ion exchange, or filtration.  For
example, iron oxide-coated sand uses adsorption and
ion exchange with surface hydroxides to selectively
remove arsenic from water.  The media requires
periodic regeneration or disposal and replacement with
new media.  The regeneration process is similar to that
used for AA, and consists of rinsing the media with a
regenerating solution containing excess sodium   ;
hydroxide, flushing with water, and neutralizing with a
strong acid, such as sulfuric acid (Ref. 11.3).

The sources used for this report contained information
on the use of surfactant-modified zeolite (SMZ) at:
bench scale, but no pilot- or full-scale applications were
identified. SMZ is prepared by treating zeolite with a
solution of surfactant, such as
hexadecyltrimethylammonium bromide (HDTMA-Br).
This process forms a stable coating on the zeolite
surface. The reported adsorption capacity of SMZ is
0.0055 grams of As(V) per gram of SMZ at 25ฐC.  SMZ
must be periodically regenerated with surfactant
solution or disposed and replaced with new SMZ (Ref.
11.17).

Media and Contaminants Treated

Adsorption is frequently used to remove organic
contaminants and metals from industrial wastewater. It
has been used to remove arsenic from groundwater and
drinking water.

Type, Number, and Scale of Identified Projects
Treating Water Containing Arsenic

Adsorption technologies to treat arsenic-contaminated
water in water are commercially available.  Information
was found on 23 applications of adsorption (Figure
11.1), including 7 full- and 5 pilot-scale projects fro
groundwater and surface water and 8 full- and 3 pilot-
scale projects for drinking water.

                    Figure 11.1
 Scale of Identified Adsorption Projects for Arsenic
                    Treatment
  Full
 Pilot
                    ^.f^-afr**,*?.,*^'
                                          15
                                  10
15
Summary of Performance Data

Adsorption treatment effectiveness can be evaluated by
comparing influent and effluent contaminant
concentrations. Table 11.1 presents the available
performance data for this technology. Two of the four
groundwater and surface water projects having both
influent and effluent arsenic concentration data had
influent concentrations greater than 0.050 mg/L.
Effluent concentrations of 0.050 mg/L or less were
                                                   11-2

-------
      Factors Affecting Adsorption Performance

       Fouling - The presence of suspended solids],
       organics, solids, silica, or mica, can cause  j
       fouling of adsorption media (Ref. 11.1,11.4).
       Arsenic oxidation state - Adsorption is moire
       effective in removing As(V) than As(III) (Ref.
       11.12).                                 :
       Flow rate - Increasing the rate of flow through
       the adsorption unit can decrease the adsorption
       of contaminants (Ref. 11.1).              ;
       Wastewater pH - The optimal pH to maximize
       adsorption of arsenic by activated alumina is
       acidic (pH 6).  Therefore, pretreatment and
       post-treatment of the water could be required
       (Ref. 11.4).
 achieved in both of the projects.  In the other two j
 groundwater and surface water projects the influent
 arsenic concentration was between 0.010 mg/L and
 0.050 mg/L, and the effluent concentration was leqs
 than 0.010 mg/L.                              :
 Of the ten drinking water projects (eight full and t\jvo
 pilot scale) having both influent and effluent arsenic
 concentration data, eight had influent concentrations
 greater than 0.050 mg/L. Effluent concentrations of
 less than 0.050 mg/L were achieved in seven ofth^se
 projects.  For two drinking water projects the influfent
 arsenic concentration was between 0.010 mg/L and
 0.050 mg/L, and the effluent concentration was less
 than 0.010 mg/L.                              j

 Projects that did not reduce arsenic concentrations ko
 below 0.050 or 0.010 mg/L do not necessarily  indicate
 that adsorption cannot achieve these levels. The  |
 treatment goal for some applications may have been
 above these levels and the technology may have been
 designed and operated to meet a higher arsenic   j
 concentration.  Information on treatment goals wasjnot
 collected for this report.                        j
                                              I
 Two pilot-scale studies were performed to compare the
 effectiveness AA adsorption on As(III) and As(V) |
 (Projects 3 and 4 in Table 11.1). For As(III), 300  hjed
volumes were treated before arsenic concentrations in
the effluent exceeded 0.050 mg/L, whereas 23,400 bed
volumes were treated for As(V) before reaching the
same concentration in the effluent. The results of tjiese
studies indicate that the adsorption capacity of AA jis
much greater for As(V).                        !
                                              !
The  case study at the end of this section discusses  in
greater detail the use of AA to remove arsenic froni
 drinking water. Information for this project is
 summarized in Table 11.1, Project 13.

 Applicability, Advantages, and Potential Limitations

 For AA adsorption media, the spent regenerating
 solution might contain a high concentration of arsenic
 and other sorbed contaminants, and can be corrosive
 (Ref. 11.3).  Spent AA is produced when the AA can no
 longer be regenerated (Ref.  11.3). The spent AA may
 require treatment prior to disposal (Ref. 11.4). Because
 regeneration of AA requires the use of strong acids and
 bases, some of the AA media becomes dissolved during
 the regeneration process.  This can reduce the
 adsorptive capacity of the AA and cause the AA
 packing to become "cemented."

 Regeneration of AC media involves the use of thermal
 energy, which could release volatile arsenic
 compounds.  Use of air pollution control equipment
 may be necessary to remove arsenic from the off-gas
 produced (Ref. 11.6).

 Competition for adsorption sites could reduce the
 effectiveness of adsorption because other constituents
 may be preferentially adsorbed, resulting in a need for
 more frequent bed regeneration or replacement.  The
 presence of sulfate, chloride, and organic compounds
 has reportedly reduced the adsorption capacity of AA
 for arsenic (Ref. 11.3). The order for adsorption
 preference for AA is provided below, with the
 constituents with the greatest adsorption preference
 appearing at the top left (Ref. 11.3):

  Off > H2AsO4- > Si(OH)3O- > F > HSeO/ > SO42'
  > H3AsO3

 This technology's effectiveness is also sensitive to a
 variety of contaminants and characteristics in the
 untreated water, and suspended solids, organics, silica,
 or mica can cause fouling. Therefore, it is typically
 applied to groundwater and drinking water, which are
 less likely to contain fouling contaminants.  It may also
 be used as a polishing step for other water treatment
 technologies.

 More detailed information on selection and design of
 arsenic treatment systems for small drinking water
 systems is available in the document "Arsenic
 Treatment Technology Design Manual for Small
Systems " (Ref. 11.20).

Summary of Cost Data

One source reported that the cost of removing arsenic
from drinking water using AA ranged from $0.003 to
                                                  11-3

-------
        Factors Affecting Adsorption Costs

      Contaminant concentration - Very high
      concentrations of competing contaminants may
      require frequent replacement or regeneration of
      adsorbent (Ref. 11.2). The capacity of the
      adsorption media increases with increasing
      contaminant concentration (Ref. 11.1,11.4).
      High arsenic concentrations can exhaust the
      adsorption media quickly, resulting in the need
      for frequent regeneration or replacement.
      Spent media - Spent media that can no longer
      be regenerated might require treatment or
      disposal (Ref. 11.4).
      Factors affecting adsorption performance -
      Items in the "Factors Affecting Adsorption
      Performance" box will also affect costs.
S0.76 per 1,000 gallons (Ref. 11.4, cost year not  ;
provided). The document "Technologies and Costs/or
Removal of Arsenic From Drinking Water" (Ref. 11.3)
contains detailed information on the cost of adsorption
systems to treat arsenic in drinking water to below the
revised MCL of 0.010 mg/L. The document includes
capital and operating and maintenance (O&M) cost
curves for four adsorption processes:
  Case Study: Treatment of Drinking Water by an
  Activated Alumina Plant

  A drinking water treatment plant using AA (see
  Table 11.1, Project 13) installed in February 1996
  has an average flow rate of 3,000 gallons per day.
  The arsenic treatment system consists of two
  parallel treatment trains, with two AA columns in
  series in each train. For each of the trains, the AA
  media in one column is exhausted and replaced
  every 1 to 1.5 years after treating approximately
  5,260 bed volumes.

  Water samples for a long-term evaluation were
  collected weekly for a year.  Pretreatment arsenic
  concentrations at the inlet ranged from 0.053 to
  0.087 mg/L with an average of 0.063 mg/L.  The
  untreated water contained primarily As(V) with only
  minor concentrations  of As(IH) and particulate
  arsenic. During the entire study, the arsenic
  concentration in the treated drinking water was
  below 0.003 mg/L. Spent AA from the system had
  leachable arsenic concentrations of less than 0.05
  mg/L, as measured by the TCLP, and therefore,
  could be disposed of as nonhazardous waste.
• AA (at various influent pH levels)
• Granular ferric hydroxide
• Greensand filtration (KMNO4 coated sand)
• AA point-of-use systems

These cost curves are based on computer cost models
for drinking water systems. The curves show the costs
for adsorption treatment systems with different design
flow rates. The document also contains information on
the disposal cost of residuals from adsorption. Many of
the technologies used to treat drinking water are
applicable to treatment of other types of water, and may
have similar costs. Table 3.4 in Section 3 of this
document contains cost estimates based on these curves
for AA and greensand filtration.
References

11.1  U.S. EPA.  Regulations on the Disposal of
      Arsenic Residuals from Drinking Water
      Treatment Plants. Office of Research and
      Development. EPA/600/R-00/025. May 2000.
      http://www.epa.gov/ORD/WebPubs/residuals/
      index.htm
11.2  Federal Remediation Technologies Reference
      Guide and Screening Manual, Version 3.0.
      Federal Remediation Technologies Roundtable.
      March 30, 2001. http://www.frtr.gov/matrix2/
      topjpage.html.
11.3  U.S. EPA.  Technologies and Costs for Removal
      of Arsenic From Drinking Water. EPA 815-R-
      00-028.  Office of Water. December 2000.
      http://www.epa.gov/safewater/ars/
      treatments_and_costs.pdf
11.4  Twidwell, L.G., et al.  Technologies and
      Potential Technologies for Removing Arsenic
      from Process and Mine Wastewater.  Presented
      at "REWAS'99." San Sebastian, Spain.
      September 1999.
      http://www.mtech.edu/metallurgy/arsenic/
      REWASAS%20for%20proceedings99%20in%2
      Oword.pdf
 11.5  U.S.  EPA. Pump and Treat of Contaminated
      Groundwater at the Mid-South Wood Products
      Superfund Site, Mena, Arkansas. Federal
      Remediation Technologies Roundtable.
       September 1998.
      http://www.frtr.gov/costperf.html.
 11.6  U.S. EPA. Final Best Demonstrated Available
       Technology (BOAT) Background Document for
       K031, K084, K101, K102, Characteristic Arsenic
       Wastes (D004), Characteristic Selenium Wastes
       (DO 10), and P and U Wastes Containing Arsenic
       and Selenium Listing  Constituents. Office of
       Solid Waste.  May 1990.
                                                  11-4

-------
11.7  U.S. EPA. Groundwater Pump and Treat  ,
      Systems: Summary of Selected Cost and   '
      Performance Information at Superfund-finaiJLced
      Sites.  EPA-542-R-01-021b. EPAOSWERJ
      December 2001. http://clu-in.org         j
11.8  MurcottS. Appropriate Remediation      j
      Technologies for Arsenic-Contaminated Wells in
      Bangladesh.  Massachusetts Institute of   '
      Technology. February 1999.             !
      http://web.mit.edu/civenv/html/people/facul1y/
      murcott.html                           ;
11.9  Haq N. Low-cost method developed to treat;
      arsenic water. West Bengal and Bangladesh
      Arsenic Crisis Information Center.  June 2001.
      http://bicn.com/acic/resources/infobank/nfb/
      2001-06-ll-nv4n593.htm
11.10 U.S. EPA. Arsenic Removal from Drinking
      Water by Iron Removal Plants. EPA 600-RT00-
      086. Office of Research and Development.
      August 2000.      '                    ;
      http://www.epa.gov/ORD/WebPubs/iron/  !
      index.html                             '•
11.11 Harbauer GmbH & Co. KG. Germany. Online
      address: http://www.harbauer-berlin.de/arsejiic.
11.12 U.S. EPA. Arsenic Removal from Drinking'
      Water by Ion Exchange and Activated Aluniina
      Plants. EPA 600-R-00-088.  Office of Research
      and Development.  October 2000.         j
      http://www.epa.gov/ncepi/Catalog/       j
      EPA600R00088.html                    !
11.13 Environmental Research Institute. Arsenic |
      Remediation Technology - AsRT.  June 28, |
      2001.  http://www.eng2.uconn.edu/~nikos/asrt-
      brochure.html.                          i
11.14 Redox Treatment of Groundwater to Remove
      Trace Arsenic at Point-of-Entry Water Treatment
      Systems. June 28, 2001.                >|
      http://phys4.harvard.edu/~wilson/Redox/   j
      Desc.html.                             |
11.15 U.S. EPA. Treatment Technologies for Site :
      Cleanup: Annual Status Report (Tenth Edition).
      Office of Solid Waste and Emergency Response.
      EPA-542-R-01-004. February 2001.      !
      http://clu-in.org/asr                     I
11.16 Electric Power Research Institute. Innovative
      Technologies for Remediation of Arsenic in; Soil
      Groundwater: Soil Flushing, In-Situ Fixatioi,
      Iron Coprecipitation, and Ceramic Membrane
      Filtration. April 2000. http://www.epri.com!
11.17 Sullivan, E. J., Bowman, R S., and Leieic, I.JA..
      Sorption of Arsenate from Soil-Washing   !
      Leachate by Surfactant-Modified Zeolite.  ;
      Prepublication draft. January, 2002.      j
      bowman@nmt.edu                     |
11.18 E-mail attachment  from Cindy Schreier, Prirfta
      Environmental to Sankalpa Nagaraja, Tetra fech
      EM Inc. June 18, 2002.                 i
11.19 Severn Trent Services.  UK.
      http://www.capitalcontrols.co.uk/
11.20 U.S. EPA. Arsenic Treatment Technology
      Design Manual for Small Systems (100% Draft
      for Peer Review). June 2002.
      http://www.epa.gov/safewater/smallsys/
      arsenicdesignmanualpeerreviewdraft.pdf
                                                 11-5

-------
                  Table 11.1
Adsorption Treatment Performance Data for Arsenic
Project
Number
Industry or Site
Type
Waste or Media
Scale"
Site Name or
Location
Initial Arsenic
Concentration
Final Arsenic
Concentration
Adsorption Process
Description11
Source
Environmental Media - Activated Alumina
1

2
3



4

—

—






Groundwater

Groundwater
Solution
containing
trivalent arsenic



Solution
containing
pentavalent
arsenic

Full

Pilot
Pilot



Pilot

—

—






—

—
Trivalent
arsenic, 0.1
mg/L

- ~

Pentavalent
arsenic, 0. 1
mg/L

<0.05 mg/L

<0.05 mg/L
Trivalent arsenic, 0.05
mg/L



Pentavalent arsenic,
0.05 mg/L

Activated alumina.
Flow rate: 300
liters/hour.
Activated alumina
adsorption at pH 5
Activated alumina
adsorption at pH 6.0 of
solution containing
trivalent arsenic. 300
bed volumes treated
before effluent exceeded
0.05 mg/L arsenic.
Activated alumina
adsorbent at pH 6.0 of
solution containing
pentavalent arsenic.
23,400 bed volumes
treated before effluent
exceeded 0.05 mg/L
arsenic.
11.9

11.4
11.3



11.3


                     11-6

-------
                        Table 11.1
Adsorption Treatment Performance Data for Arsenic (continued)
rroject
Number
Industry or Site
Type
Waste or Media
Scale3
Site Name or
Location
Initial Arsenic
Concentration
Final Arsenic
Concentration
Adsorption Process
Description1"
Source
Environmental Media - Activated Carbon
5
6
7
8
9
10
Wood preserving
Wood Preserving
Wood Preserving
Wood Preserving
Chemical mixing
and batching
Chemical
Manufacturing
Groundwater
Groundwater,
27,000 gpd
Groundwater,
3,000 gpd
Groundwater,
4,000 gpd
Groundwater,
43,000 gpd
Groundwater,
65,000 gpd
Full
Full
Full
Full
Full
Full
Mid-South Wood
Product Superfund
Site, Mena, AS
North Cavalcade
Street Superfund Site
Houston, TX
Saunders Supply
Company Superfiind
Site, Chuckatuck,
VA
McCormick and
Baxter Creosoting
Co. Superfund Site,
Portland, OR
Baird and McGuire
Superfund Site,
Holbrook, MA
Greenwood
Chemical Superfund
Site, Greenwood,
VA
0.018 mg/L





O.005 mg/L (29 of 35
monitoring wells)





Treatment train
consisting of oil/water
separation, filtration,
and carbon adsorption.
Performance data are for
the entire treatment
train.
Treatment train
consisting of filtration
followed by carbon
— -adsorption 	 --
Treatment train
consisting of metals
precipitation, filtration,
and carbon adsorption
Treatment train
consisting of filtration,
ion exchange, and
carbon adsorption
Treatment train
consisting of air
stripping, metals
precipitation, filtration,
and carbon adsorption
Treatment train
consisting of metals
precipitation, filtration,
UV oxidation and
carbon adsorption
11.5
11.7
11.7
11.7
11.7
11.7
                         11-7

-------
                       Table 11.1
Adsorption Treatment Performance Data for Arsenic (continued)
! 	 "K 	 "!-|p
Project
Numberi
Environn
11
12
Industry or Site
Type j
Waste or Media
Scale"
Site Name or
Location
Initial Arsenic
Concentration
Final Arsenic
Concentration
Adsorption Process
Description11 !
lental Media - Iron-Based Media
Landfill

Groundwater
Groundwater,
3,600gpd
Pilot
Pilot

CA

0.018 mg/L
0.027 mg/L
O.002 mg/L
	
Treatment train
consisting of
precipitation from barite
addition followed by an
iron filings and sand
media filter.
Performance data are for
the entire treatment
train.
Fixed-bed adsorber with
sulfur-modified iron
adsorbent; 13,300 bed
volumes put through
unit
Drinking Water - Activated Alumina
13
14
15
16
17

-
-

-
Drinking water
Drinking water
Drinking water
Drinking water
Drinking water,
14,000 gpd
Full
Full
Full
Full
Full

—
Project Earth
Industries, Inc.

Bow,NH
0.063 mg/L
0.034 - 0.087
mg/L
0.34 mg/L
0.049 mg/L
0.057 - 0.062
mg/L
O.003 mg/L
O.05 mg/L
0.01 - 0.025 mg/L
O.003 mg/L
0.050 mg/L
Two activated alumina
columns in series, media
replaced in one column
every 1.5 years
Activated alumina
Activated alumina
Two activated alumina
columns in series, media
replaced in column tank
every 1.5 years
Activated alumina
Drinking Water - Iron-Based Media
18

Drinking water
Full
Harbauer GmbH &
Co., Berlin,
Germany
0.3 mg/L
<0.01 mg/L
Granular feme
hydroxide
Source

11.8,
11.13
11.18

11.3
11.12
11.8
11.3
11.3

11.11
                           11-8

-------
                                                                   Table 11.1
                                         Adsorption Treatment Performance Data for Arsenic (continued)
project
Number
19
20
21
Drinking
_ 22 _
23
Industry or Site
Type

"
"""
Waste or Media
Drinking Water
Drinking water
Drinking water
Scale"
Pilot
Pilot
Full
Site Name or
Location

—
--
Initial Arsenic
Concentration
0.1- 0.18 mg/L
0.180mg/L
0.02mg/L
Final Arsenic
Concentration
<0.01 mg/L
0.010 mg/L
0.003 mg/L
Adsorption Process
Description11
Fixed bed adsorber with
ferric hydroxide-coated
newspaper pulp; 20,000
bed volumes treated
before effluent exceeded
0.01 mg/L arsenic
Granular ferric
hydroxide
Fixed bed adsorber with
ferric oxide granules
Water - Other or Unknown Media
	 	 	 _r^ 	

_ JDrinking water__
Drinking water
_Full_
Pilot
	 	 ™ 	 	
ADI International
	 5mg/L 	

- 	 	 0.01 mg/L -- -

- Copper-zinc-granules -
Adsorption in
pressurized vessel
containing proprietary
media at pH 5.5 to 8.0
Source
11.15
11.16
11.19

-1U4-
11.1
a     Excluding bench-scale treatments.
b     Some processes employ a combination of adsorption, ion exchange, oxidation, precipitation/coprecipitation, or filtration to remove arsenic from water.
AA = activated alumina
EPT = Extraction procedure toxicity test
mg/L = milligrams per liter
RCRA = Resource Conservation and Recovery
Act

gpd = gallons per day
mgd = million gallons per day
TCLP = Toxicity characteristic leaching
procedure mg/kg = milligrams per kilogram
- = Not available
 TWA = Total waste analysis
WET = Waste extraction test
                                                                     11-9

-------

-------
 12.0  ION EXCHANGE TREATMENT FOR
 ARSENIC
  Summary

  Ion exchange has been used to treat groundwater
  and drinking water containing arsenic.  Based on the
  information collected to prepare this report, this  i
  technology typically can reduce arsenic
  concentrations to less than 0.050 mg/L and in some
  cases has reduced arsenic concentrations to below
  0.010 mg/L. Its effectiveness is sensitive to a    ;
  variety of untreated water contaminants and
  characteristics. It is used less frequently than
  precipitation/coprecipitation, and is most commonly
  used to treat groundwater and drinking water, or as a
  polishing step for other water treatment processes.
Technology Description and Principles          !
The medium used for ion exchange is typically a resin
made from synthetic organic materials, inorganic   '
materials, or natural polymeric materials that contaih
ionic functional groups to which exchangeable ions'are
attached (Ref. 12.3). Four types of ion exchange media
have been used (Ref. 12.1):                      '
                                               i
•  Strong acid                                 |
•  Weak acid                                  l
•  Strong base                                 j
•  Weak base                                  '
                                               i
Strong and weak acid resins exchange cations while;
strong and weak base resins exchange anions. Because
dissolved arsenic is usually in an anionic form, and J
weak base resins tend to be effective over a smaller pH
  Technology Description: Ion exchange is a
  physical/chemical process in which ions held
  electrostatically on the surface of a solid are
  exchanged for ions of similar charge in a solution.^
  It removes ions from the aqueous phase by the
  exchange of cations or anions between the
  contaminants and the exchange medium (Ref. 12.1,
  12.4, 12.8).

  Media Treated:
  •    Groundwater
  •    Surface water
  •    Drinking water

  Exchange Media Used in Ion Exchange to Treat
  Arsenic:
      Strong base anion exchange resins           ;
          Model of an Ion Exchange System
                                                          Contaminated
                                                            Water   •
       Ion Exchanj
         Resin
                                          Effluent
 range, strong base resins are typically used for arsenic
 treatment (Ref. 12.1).

 Resins may also be categorized by the ion that is
 exchanged with the one in solution.  For example,
 resins that exchange a chloride ion are referred to as
 chloride-form resins. Another way of categorizing
 resins is by the type of ion in solution that the resin
 preferentially exchanges. For example, resins that
 preferentially exchange sulfate ions are referred to as
 sulfate-selective.  Both sulfate-selective and nitrate-
 selective resins have been used for arsenic removal
 (Ref. 12.1).

 The resin is usually packed into a column, and as
 contaminated water is passed through the column,
 contaminant ions are exchanged for other ions such as
 chloride or hydroxide in the resin (Ref.  12.4).  Ion
 exchange is often preceded by treatments such as
 filtration and oil-water separation to remove organics,
 suspended solids, and other contaminants that can foul
the resins and reduce their effectiveness.
 Ion exchange resins must be periodically regenerated to
remove the adsorbed contaminants and replenish the
 exchanged ions (Ref. 12.4). Regeneration of a resin
 occurs in three steps:

 • Backwashing
 • Regeneration with a solution of ions
• Final rinsing to remove the regenerating solution

The regeneration process results in a backwash
solution, a waste regenerating solution, and a waste
rinse water.  The volume of spent regeneration solution
ranges from 1.5 to 10 percent of the treated water
volume depending on the feed water quality and type of
ion exchange unit (Ref. 12.4). The number of ion
exchange bed volumes that can be treated before
                                                   12-1

-------
regeneration is needed can range from 300 to 60,000
(Ref. 12.1). The regenerating solution may be used up
to 25 times before treatment or disposal is required.
The final rinsing step usually requires only a few bed
volumes of water (Ref. 12.4).

Ion exchange can be operated using multiple beds in
series to reduce the need for bed regeneration; beds first
in the series will require regeneration first, and fresh
beds can be added at the end of the series.  Multiple
beds can also allow for continuous operation because
some of the beds can be regenerated while others
continue to treat water. Ion exchange beds are typically
operated as a fixed bed, in which the water to be treated
is passed over an immobile ion exchange resin.  One
variation on this approach is to operate the bed in a non-
fixed, countercurrent fashion in which water is applied
in one direction, usually downward, while spent ion
exchange resin is removed from the top of the bed.
Regenerated resin is added to the bottom of the bed.
This method may reduce the frequency of resin
regeneration (Ref. 12.4).

Media and Contaminants Treated

Anion exchange resins are used to remove soluble
forms of arsenic from wastewater, groundwater, and
drinking water (Ref. 12.1,12.4). Ion exchange
treatment is generally not applicable to soil and  waste.
It is commonly used in drinking water treatment for
softening, removal of calcium, magnesium, and other
cations in exchange for sodium, as well as removing
nitrate, arsenate, chromate, and selenate (Ref. 12.9).

Type, Number, and Scale of Identified Projects
Treating Water Containing Arsenic

Ion exchange of arsenic and groundwater, surface
water, and drinking water is commercially available.
Information is available on seven full-scale applications
(Figure 12.1), including three applications to     "
groundwater and surface water,  and four applications to
drinking water. No pilot-scale applications or
applications to industrial wastewater were found in the
sources researched.

Summary of Performance Data

Table 12.1 presents the performance data found for this
technology.  Ion exchange treatment effectiveness  can
be evaluated by comparing influent and effluent
contaminant concentrations. The single surface water
project with both influent and effluent arsenic   r
concentration data had an influent concentrations of
 0.0394 mg/L, and an effluent concentration of 0.0229
mg/L.  Of the three drinking water projects with both
                   Figure 12.1
    Scale of Identified Ion Exchange Projects for
                Arsenic Treatment
  Full
 Pilot
                               I '•{ >*
influent and effluent concentration data, all had influent
concentrations greater than 0.010 mg/L.  Effluent
concentrations of less than 0.010 mg/L were
consistently achieved in only one of these projects.

Projects that did not reduce arsenic concentrations to
below 0.050 or 0.010 mg/L do not necessarily indicate
that ion exchange cannot achieve these levels. The
treatment goal for some applications could have been
above these levels and the technology may have been
designed and operated to meet a higher arsenic
concentration. Information on treatment goals was not
collected for this report.
  Factors Affecting Ion Exchange Performance

      Valence state - As(III) is generally not
      removed by ion exchange (Ref. 12.4).
  •   Presence of competing ions - Competition for
      the exchange ion can reduce the effectiveness
      of ion exchange if ions in the resin are replaced
      by ions other than arsenic, resulting in a need
      for more frequent bed regeneration (Ref. 12.1,
      12.9).
  •   Fouling - The presence of organics, suspended
      solids, calcium, or iron, can cause fouling of
      ion exchange resins (Ref. 12.4).
      Presence of trivalent iron - The presence of
      Fe (III) could cause arsenic to form complexes
      with the iron that are not removed by ion
      exchange (Ref. 12.1).
      pH - For chloride-form, strong-base resins, a
      pH in the range of 6.5  to 9 is optimal. Outside
      of this range, arsenic removal effectiveness
      decreases quickly (Ref. 12.1).
                                                    12-2

-------
 The case study at the end of this section further  l
 discusses the use of ion exchange to remove arsenic
 from drinking water.  Information for this project is
 summarized in Table 12.1, Project 1.            ;

 Applicability, Advantages, and Potential Limitations

 For ion exchange systems using chloride-form resins,
 the treated water could contain increased levels of
 chloride ions and as a result be corrosive. Chlorides
 can also increase the redox potential of iron, thus '
 increasing the potential for water discoloration if the
 iron is oxidized.  The ion exchange process can also
 lower the pH of treated waters (Ref. 12.4).       j
                                             i
                                             i
 For ion exchange resins used to remove arsenic fhkn
 water, the spent regenerating solution might contain a
 high concentration of arsenic and other sorbed
 contaminants, and could be corrosive. Spent resin' is
produced when the resin can no longer be regenerated.
The spent resin may require treatment prior to reude or
disposal (Ref. 12.8).                           !

The order for exchange for most strong-base resins| is
provided below, with the constituents with the greatest
adsorption preference appearing at the top left (ReJF.
 12.4).                                        i

HCrCV > CrO42- > C1CV  > SeO42- > SO42- > NO/ >| Br
> (HP042-, HAs042-, SeO32-, CO32-) > CN" > NO
(H2PO4-, H2AsO4-, HCCV)
                             3              2
                          OH' > CH3COO- > F
The effectiveness of ion exchange is also sensitiveto a
variety of contaminants and characteristics in the  !
untreated water, and organics, suspended solids,  ;
calcium, or iron can cause fouling. Therefore, it is!
typically applied to groundwater and drinking wat^r,
which are less likely to contain fouling contaminants. It
may also be used as a polishing step for other watejr
treatment technologies.                         i
                                              I
More detailed information on selection and design of
arsenic treatment systems for small drinking water!
systems is available in the document "Arsenic     \
Treatment Technology Design Manual for Small  \
Systems" (Ref. 12.10).                         j
                                              j
                                              I
Summary of Cost Data                        !
                                              i
One project reported a capital cost for an ion exchange
system of $6,886 with an additional $2,000 installation
fee (Ref. 12.9, cost year not' provided). The capacity of
the system and O&M costs were not reported. Cost
data for other projects using ion exchange were nolj
found.
                                                         Factors Affecting Ion Exchange Costs

                                                         •   Bed regeneration - Regenerating ion
                                                             exchange beds reduces the amount of waste for
                                                             disposal and the cost of operation (Ref. 12.1).
                                                             Sulfate - Sulfate (SO4) can compete with
                                                             arsenic for ion exchange sites, thus reducing
                                                             the exchange capacity of the ion exchange
                                                             media for arsenic. This can result in a need for
                                                             more frequent media regeneration or
                                                             replacement, and associated higher costs (Ref.
                                                             12.1).
                                                         •   Factors affecting ion exchange performance
                                                             - Items in the "Factors Affecting Ion Exchange
                                                             Performance" box will also affect costs.
The document "Technologies and Costs for Removal of
Arsenic From Drinking Water" (Ref. 12.1) contains
additional information on the cost of ion exchange
systems to treat arsenic in drinking water to levels
below the revised MCL of 0.010 mg/L. The document
includes capital and O&M cost curves for ion exchange
at various influent sulfate (SO4) concentrations.  These
cost curves are based on computer cost models for
drinking water treatment systems.

The curves estimate the costs for ion exchange
treatment systems with different design flow rates. The
document also contains information on the disposal cost
for residuals from ion exchange. Table 3.4 in Section 3
of this document contains cost estimates based on these
curves for ion exchange. Many of the technologies
used to treat drinking water are applicable to treatment
of other types of water, and may have similar costs.
                                                        Case Study: National Risk Management
                                                        Research Laboratory Study

                                                        A study by EPA ORD's National Risk Management
                                                        Research Laboratory tested an ion exchange system
                                                        at a drinking water treatment plant. Weekly
                                                        sampling for one year showed that the plant
                                                        achieved an average of 97 percent arsenic removal.
                                                        The resin columns were frequently regenerated
                                                        (every 6 days). Influent arsenic concentrations
                                                        ranged from 0.045 to 0.065 mg/L and effluent
                                                        concentrations ranged from 0.0008 to 0.0045 mg/L
                                                        (Ref. 12.9) (see Project 1, Table 12.1).
                                                   12-3

-------
References

12.1    U.S. EPA. Technologies and Costs for
       Removal of Arsenic From Drinking Water.
       EPA-R-00-028. Office of Water. December,
       2000. http://www.epa.gov/safewater/ars/  ,'
       treatments_and_costs.pdf
12.2   U.S. EPA. Arsenic & Mercury - Workshop on
       Removal, Recovery, Treatment, and Disposal.
       Office of Research and Development. EPA-
       600-R-92-105. August 1992.
       http://www.epa.gov/ncepihom
12.3   Federal Remediation Technologies Reference
       Guide and Screening Manual, Version 3.0.
       Federal Remediation Technologies Roundtable
       (FRTR).
       http://\vww.frtr.gov/matrix2/top_page.html.
12.4   U.S. EPA. Regulations on the Disposal of
       Arsenic Residuals from Drinking Water
       Treatment Plants. EPA-600-R-00-025.  Office
       of Research and Development. May 2000.!"'
       http://www.epa.gov/ncepihom
12.5   Tidwell, L.G., et al. Technologies and Potential
       Technologies for Removing Arsenic from
       Process and Mine Wastewater. Presented at
       "REWAS'99." San Sebastian, Spain.
       September 1999.                       :
       http://www.mtech.edu/metallurgy/arsenic/
       REWASAS%20for%20proceedings99%20in%2
       Oword.pdf
12.6   U.S. EPA. Final Best Demonstrated Available
       Technology (BDAT) Background Document for
       K031, K084, K101, K102, Characteristic
       Arsenic Wastes (D004), Characteristic    •
       Selenium Wastes (DO 10), and P and U Wastes
       Containing Arsenic and Selenium Listing
       Constituents. Office of Solid Waste. May;
       1990.
12.7   U.S. EPA. Groundwater Pump and Treat
       Systems: Summary of Selected Cost and
       Performance Information at Superfund-financed
       Sites. EPA-542-R-01-021b. EPAOSWER,
       December 2001. http://clu-in.org
12.8   Murcott, S. Appropriate Remediation
       Technologies for Arsenic-Contaminated Wells
       in Bangladesh. Massachusetts Institute of
       Technology. February 1999.            L
       http://web.mit.edu/civenv/htmVpeople/faculty/
       murcott.html
12.9   U.S. EPA. Arsenic Removal from Drinking
       Water by Ion Exchange and Activated Alumina
       Plants. EPA-600-R-00-088. Office of Research
       and Development. October 2000.        ;
       http://www.epa.gOV/ORD/WebPubs/exchange/E
       PA600R00088.pdf                    I
12.10   U.S. EPA. Arsenic Treatment Technology
       Design Manual for Small Systems (100% Draft
       for Peer Review). June 2002.
       http://www.epa.gov/safewater/smallsys/
       arsenicdesignmanualpeerreviewdraft.pdf
                                                 12-4

-------
                   Table 12.1
Ion Exchange Treatment Performance Data for Arsenic


Project
Number
Industry or Site
Type
Waste or
Media
Scale
Site Name or
Location
Ion Exchange
Media or Process
ifntreafed
Arsenic
Concentration
Treated Arsenic
Concentration
Ion Exchange Media
Regeneration
Information
Source
Drinking Water
1
2

3
4
Environn
5
6

—



dental Media
Wood Preserving,
spill of chromated
copper arsenate
Waste disposal
Drinking
Water
Drinking
Water

Drinking
Water
Drinking
Water

Surface water
Groundwater,
43,000 gpd
Full
Full

Full
Full

—



Treatment train
consisting of
potassium
permanganate
greensand oxidizing
filter followed by a
mixed bed ion
exchange system
Treatment train
-consisting^of a-solid
oxidizing media
filter followed by an
anion exchange
system
Strongly basic gel
ion exchange resin in
chloride form
Chloride-form
strong-base resin
anion-exchange
process
0.040 - 0.065
mg/La
0.019-0.055
	 mg/La- 	 -
0.045 - 0.065
mg/L

O.003 mg/La
<0.005 - 0.080
	 ~mg/La 	 •-
0.0008 - 0.0045
mg/L
0.002 mg/L
Bed regenerated every
6 days
-

Resin regenerated
every four weeks
Spent NaCl brine
reused to regenerate
exhausted ion-
exchange bed

Full
Full
Vancouver,
Canada (site
name
unknown)
Higgins Farm
Superfund
Site, Franklin
Township, NJ
Anion and cation
resins
Treatment train
consisting of air
stripping, metals
precipitation,
filtration, and ion
exchange
0.0394 mg/L

0.0229 mg/L



12.1
12.1

12.9
12.8

12.2
12.7


                     12-5

-------
                                                                    Table 12.1
                                         Ion Exchange Treatment Performance Data for Arsenic (continued)
Project
Number
7
Industry; or Site |
Type
Wood preserving
Waste or
Media
Groundwater,
4,000 gpd
Scale
Full
Site Name ior
Location
McCormick
and Baxter
Creosoting
Co. Superfund
Site, Portland,
OR
: Ion -Exchange;
Media or Process
Treatment train
consisting of
filtration, ion
exchange, and
carbon adsorption
f ซ-,..ซ'ซ!** •
ntreatea
Arsenic
Concentration

Treated Arsenic
Concentration

ion Exchange Media
Regeneration
Information

Source
12.7
 a Data are for entire treatment train, including unit operations that are not ion exchange.
 — = Not available.
 TWA = Total waste analysis.
. gpd = gallons per day     ..            .             ._	 . .
 mg/L = milligrams per liter.
                                                                        12-6

-------
13.0    PERMEABLE REACTIVE BARRIERS
        FOR ARSENIC                     !
  Summary                                 '.

  Permeable reactive barriers (PRBs) are being used
  to treat arsenic in ground-water at full scale at only a
  few sites. Although many candidate materials for
  the reactive portion of the barrier have been tested at
  bench scale, only zero valent iron and limestone
  have been used at full scale. The installation  -
  techniques for PRBs are established for depths less
  than 30 feet, and require innovative installation
  techniques for deeper installations.
Technology Description and Principles       j

PRBs are applicable to the treatment of both organic
and inorganic contaminants. The former usually are
broken down into carbon dioxide and water, while| the
latter are converted to species that are less toxic of less
mobile. The most frequent applications of PRBs is the
in situ treatment of groundwater contaminated with
chlorinated solvents. A number of different treatment
media have been used, the most common being zero-
valent iron (ZVI). Other media include hydrated lime,
slag from steelmaking processes that use a basic ojxygen
furnace, calcium oxides, chelators (ligands selected  for
their specificity for a given metal), iron oxides,  |
sorbents, substitution agents (e.g., ion exchange resins)
  Technology Description:  Permeable reactive
  barriers (PRBs) are walls containing reactive media
  that are installed across the path of a contaminated
  groundwater plume to intercept the plume. The
  barrier allows water to pass through while the media
  remove the contaminants by precipitation,
  degradation, adsorption, or ion exchange.

  Media Treated:
  •   Groundwater (in situ)

  Chemicals and Reactive Media Used in PRBs to
  Treat Arsenic:
  •   Zero valent iron (ZVI)
  •   Limestone
  •   Basic oxygen furnace  slag
  •   Surfactant modified zeolite
  •   Ion exchange resin

  Installation Depth:
     Up to 30 feet deep using established techniques
  •   Innovative techniques  required for depths
     greater than 30 feet
and microbes (Ref. 13.6, 13.8, 13. 18). The cost of the
reactive media will impact the overall cost of PRB
remedies.  The information sources used for this report
included information about PRB applications using
ZVI, basic oxygen furnace slag, limestone, surfactant
modified zeolite, and ion exchange resin to treat
arsenic.
                              Model of a Permeable Reactive Barrier System
     Plume
                      Direction of
                Groundwater Flow
                    Porous Treatment Media
    . -*v  ->-
    "*.,   '  V   ' *
       >f  f~^ป~
Decreased Conta'minant
   '  Concentratiorf "
                                                  13-1

-------
For the PRB projects identified for this report, ZVI was
the most commonly used reactive media. As
groundwater reacts with ZVI, pH increases, Eh
decreases, and the concentration of dissolved  hydrogen
increases. These basic chemical changes promote a
variety of processes that impact contaminant
concentrations. Increases in pH favor the precipitation
of carbonates of calcium and iron as well as insoluble
metal hydroxides. Decreases hi Eh drive reduction of
metals and metalloids with multiple oxidation states.
Finally, an increase in the partial pressure of hydrogen
in subsurface systems supports the activity of various
chemotrophic organisms that use hydrogen as an energy
source, especially sulfate-reducing bacteria and
iron-reducing bacteria (Ref. 13.15).

Arsenate [As (V)] ions bind tightly to the iron filings,
causing the ZVI to be oxidized to ferrous iron,     '
aerobically or anaerobically in the presence of water, as
shown by the following reactions:

(anaerobic)   Feฐ + 2H2O - Fe+2 + H2 + 2OH"
(aerobic)     2Feฐ -t- 2H2O + O2 =ป 2Fe+2 + 4OH'    '

The process results in a positively charged iron surface
that sorbs the arsenate species by electrostatic
interactions (Ref. 13.5,13.17).

In systems where dissolved sulfate is reduced to sulfide
by sulfate-reducing bacteria, arsenic may be removed
by the precipitation of insoluble arsenic sulfide (As2S3)
or co-precipitated with iron sulfides (FeS) (Ref. 13.15).

PRBs can be  constructed by excavating a trench of the
appropriate width and backfilling it with a reactive
medium. Commercial PRBs are built in two basic  *~
configurations: the funnel-and-gate and the continuous
wall.  The funnel-and-gate uses impermeable walls,;for
example, sheet pilings or slurry walls, as a "funnel" to
direct the contaminant plume to a "gate(s)" containing
the reactive media, while the continuous wall transects
the flow path of the plume with reactive media (Ref.
13.6).

Most PRBs installed to date have had depths  of 50 feet
(ft) or less. Those having depths of 30 ft or less can be
installed with a continuous trencher, while depths
between 30 and 70 ft require a more innovative    i
installation method, such as biopolymers. Installation
of PRBs at depths greater than 70 ft is more challenging
(Ref.  13.13).

Media and Contaminants Treated

This technology can  treat both organic and inorganic
contaminants. Organic contaminants are broken down
into less toxic elements and compounds, such as  carbon
dioxide and water. Inorganic contaminants are
converted to species that are less toxic or less mobile.
Inorganic contaminants that can be treated by PRBs
include, but are not limited to, chromium (Cr), nickel
(Ni), lead (Pb), uranium (U), technetium (Tc), iron (Fe),
manganese (Mn), selenium (Se), cobalt (Co), copper
(Cu), cadmium (Cd), zinc (Zn), arsenic (As), nitrate
(NO3-), sulfate (SO420, and phosphate (PO43-). The
characteristics that these elements have in common is
that they can undergo redox reactions and can form
solid precipitates with common groundwater
constituents, such as carbonate (CO32~), sulfide (S2~),
and hydroxide (OH")-  Some common sources of these
contaminants are mine tailings, septic systems, and
battery recycling/disposal facilities (Ref.  13.5, 13.6,
13.14).

PRBs are designed to treat groundwater in situ.  This
technology is not applicable to other contaminated
media such as soil, debris, or industrial wastes.

Type, Number, and Scale of Identified  Projects
Treating Water Containing Arsenic

PRBs are commercially available and are being used
to treat groundwater containing arsenic at a full scale at
two Superfund sites, the Monticello Mill  Tailings and
Tonolli Corporation sites, although arsenic is not the
primary target contaminant for treatment  by the
technology at either site (Ref. 13.1).  At a third
Superfund site, the Asarco East Helena site, this
technology has been tested at a bench scale, and
implementation at a full scale to treat arsenic is
currently planned (Ref. 13.15). In 1999,  a pilot-scale
treatment was conducted at Bodo Canyon Disposal Cell
Mill Tailings Site, Durango, Colorado, to remediate
groundwater contaminated with arsenic (Ref. 13.12).
In addition, PRBs have been used in two  bench-scale
treatability studies by the U.S. Department of Energy's
Grand Junction Office (GJO) to evaluate  their
application to the Monticello Mill Tailings site and a
former uranium ore processing site (Ref.  13.3).  Figure
13.1 shows the number of applications found at each
scale.

Additional bench-scale studies of the treatment of
arsenic using PRBs that contain various reactive media
are listed below (Ref. 13.8, 13.11).  These studies  were
not conducted to evaluate the application of PRBs to
specific sites.  The organizations conducting the studies
are listed in parentheses.  However, no performance
data are available for the studies, and therefore, they are
not included in Figure 13.1 above, or in Table 13.1.
                                                   13-2

-------
 Other Bench-Scale Studies Using Adsorption or Ion
 Exchange Barriers                            j

     Activated alumina (Diipont)               \
 •   Bauxite (Dupont)                         ,
 •   Ferric oxides and oxyhydroxides (Dupont,   ,
     University of Waterloo),                  ;
     Peat, humate, lignite, coal (Dupont)        >
 •   Surfactant-modified zeolite (New Mexico Institute
     of Mining and Technology)                (

 Other Bench-Scale Studies Using Precipitation Barriers
                                             i
     Ferrous hydroxide, ferrous carbonate, ferrous;
     sulfide (Dupont)                          !
 •   Limestone (Dupont)                      '
 •   Zero-Valent Metals (DOE GJO)            ;
                                             i
                    Figure 13.1
    Scale of Identified Permeable Reactive Barrier
           Projects for Arsenic Treatment
    Full
   Pilot
 r>   u
 jjcncii flfcjii^^^                               ซfe*

Summary of Performance Data               I
                                             I
Table 1 provides performance data for full-scale PRB
treatment of groundwater contaminated with arsenic at
three sites, two pilot-scale treatability study and five
bench-scale treatability studies. PRJB performance'
typically is measured by taking groundwater samples at
points upgradient and downgradient of the wall and
measuring the concentration of contaminants of cohcern
at each point. Data on the Monticello site show a 1
reduction in arsenic concentration from a range of J3.010
to 0.013 mg/L before installation of the PRB to <0;002
mg/L after the installation of a PRB.  One pilot-scale
study showed a reduction in arsenic concentrations
from 0.4  mg/L to 0.02 mg/L.  Four bench-scale   l:
treatability studies also show a reduction in arsenic
concentrations.                                I
   Factors Affecting PRB Performance

       Fractured rock - The presence of fractured
       rock in contact with the PRB may allow
       groundwater to flow around, rather than
       through, the PRB (Ref. 13.6).
       Deep aquifers and contaminant plumes -
       PRBs may be difficult to install for deep
       aquifers and contaminant plumes (>70 ft deep)
       (Ref. 13.13).
       High aquifer hydraulic conductivity - The
       hydraulic conductivity of the barrier must be
       greater than that  of the aquifer to prevent
       preferential flow around the barrier (Ref.
       13.13).
       Stratigraphy - Site stratigraphy may affect
       PRB installation. For example, clay layers
       might be "smeared" during installation,
       reducing hydraulic conductivity near the PRB
       (Ref. 13.6).
       Barrier plugging - Permeability and reactivity
   1 '•-   of the barrier may be reduced by precipitation
      products and microbial growth (Ref. 13.6).
Applicability, Advantages, and Potential Limitations

PRBs are a passive treatment technology, designed to
function for a long time with little or no energy input.
They produce less waste than active remediation (for
example, extraction systems like pump and treat), as the
contaminants are immobilized or altered in the
subsurface (Ref. 13.14).  PRBs can treat groundwater
with multiple contaminants and can be effective over a
range of concentrations.  PRBs require no aboveground
equipment, except monitoring devices, allowing return
of the property to  economic use during remediation
(Ref. 13.5, 13.14). PRBs are best applied to shallow,
unconfined aquifer systems in unconsolidated deposits,
as long as the reactive material is more conductive than
the aquifer.  (Ref.  13.13).

PRBs rely on the natural movement of groundwater;
therefore, aquifers with low hydraulic conductivity can
require relatively long periods of time to be remediated.
In addition, PRBs  do not remediate the entire plume,
but only the  portion  of the plume that has passed
through the PRB.  Because cleanup of groundwater
contaminated with arsenic has been conducted at only
two Superfund sites  and these barriers have been
recently installed (Tonolli in 1998 and Monticello in
1999),  the long-term effectiveness of PRBs for arsenic
treatment has not been demonstrated (Ref.  13.13).
                                                  13-3

-------
 Case Study: Monticello Mill Tailings Site
 Permeable Reactive Barrier

 The Monticello Mill Tailings in Southeastern Utah
 is a former uranium/vanadium processing mill and
 mill tailings impoundment (disposal pit). In January
 1998, the U.S.  Department of Energy completed an
 interim investigation to determine the nature and
 extent of contamination in the surface water and  ,
 groundwater in operable unit 3 of the site. Arsenic
 was one among several contaminants in the
 groundwater, and was found at concentrations
 ranging from 0.010 to 0.013 mg/L.  A PRB
 containing ZVI was constructed in June 1999 to
 treat heavy metal and metalloid contaminants in the
 groundwater. Five rounds of groundwater sampling
 occurred between June 1999 and April 2000, and
 was expected to continue on a quarterly basis until
 July 2001. The average concentration of arsenic
 entering the PRB, as measured from September to
 November 1999 was 0.010 mg/L, and the effluent
 concentration, measured in April 2000, was less
 than 0.0002 mg/L (Ref. 13.1,13.2,13.14) (see
 Project 2,  Table 13.1).
Summary of Cost Data

EPA compared the costs of pump-and-treat systems at
32 sites to the costs of PRBs at 16 sites. Although the
sites selected were not a statistically representative
sample of groundwater remediation projects, the capital
costs for PRBs were generally lower than those for |
pump and treat systems (Ref. 13.13).  However, at the
Monticello site, estimates showed that capital costs!for
a PRB were greater than those for a pump-and-treat
system, but lower operations and  maintenance costs
would result in a lower life-cycle cost to achieve similar
cleanup goals. For the PRB at the Monticello site, total
capital cost was $1,196,000, comprised of $1,052,0'00
for constniction and $144,000 for the reactive PRB"
media. Construction costs are assumed to include
actual construction costs and not design activities or
treatability studies (Ref. 13.14, cost year not provided).
Cost data for the other projects described in the section
are not available.

References

13.1  U.S. EPA. Treatment Technologies for Site
      Cleanup: Annual Status Report (Tenth Edition).
      Office of Solid Waste and Emergency Response.
      EPA-542-R-01-004.  February 2001. http://clu-
      in.org
 Factors Affecting PRB Costs

     PRB depth - PRBs at depths greater than 30
     feet may be more expensive to install, requiring
     special excavation equipment and construction
     materials (Ref. 13.13).
     Reactive media - Reactive media vary in cost,
     therefore the reactive media selected can affect
     PRB cost.
     Factors affecting PRB performance - Items in
     the "Factors Affecting PRB Performance" box
     will also affect costs.
13.2  Personal communication with Paul Mushovic,
      RPM, Monticello Mill Tailings - OU3 Superfund
      site.  April 20, 2001.
13.3  U.S. Department of Energy, Grand Junction
      Office (DOE-GJO). Permeable Reactive
      Barriers: Treatability Studies. March 2000.
      http://www.doegjpo.com/.
13.4  Federal Remediation Technologies Roundtable:
      Remediation Technologies Screening Matrix and
      Reference Guide Version 3.0.
      http://www.frtr.gov/matrix2/top_page.html.
13.5  Ott N. Permeable Reactive Barriers for
      Inorganics. National Network of Environmental
      Management Studies (NNEMS) Fellow. July
      2000. http://www.clu-in.org.
13.6  U.S.  EPA. Permeable Reactive Barrier
      Technologies for Contaminant Remediation.
      Office of Research and Development. EPA-600-
      R-98-125. September 1998.
      http ://www.epa.gov/ncepi/Catalog/
      EPA600R98125.html                  :
13.7  U.S.  EPA Technology Innovation Office and
      Office of Research and Development.
      Remediation Technologies Development Forum
      (RTDF).  Permeable Reactive Barrier Installation
      Profiles.  January 2000.
      http://www.rtdf.org/public/permbarr/prbsumms/.
13.8  DOE - GJO. Research and Application of
      Permeable Reactive Barriers. K0002000.  April
      1998.
      http://www.gwrtac.org/pdf/permeab2.pdf
 13.9  Baker MJ, Blowes DW, Ptacek CJ. Phosphorous
      Adsorption and Precipitation in a Permeable
      Reactive Wall:  Applications for Wastewater
      Disposal Systems.  International  Containment
      Technology Conference and Exhibition,
      February 9-12,1997.  St. Petersburg, Florida.
                                                  13-4

-------
13.10 McRae CW, Blowes DW, Ptacek CJ.      ;
      Laboratory-scale investigation of remediation of
      As and Se using iron oxides. Sixth Symposium
      and Exhibition on Groundwater and Soil   !
      Remediation, March 18-21, 1997.  Montreaj,
      Quebec, Canada.                       |
13.11 U.S. EPA. In Situ Remediation Technology
      Status Report: Treatment Walls.  Office of'Solid
      Waste and Emergency Response. EPA 542-K-
      94-004. April 1995. http://www.clu-in.orgi
13.12 U.S. EPA. Innovative Remediation
      Technologies: Field Scale Demonstration !
      Projects in North America, 2nd Edition. Office of
      Solid Waste and Emergency Response. EPA-
      542-B-00-004. June 2000.  http://clu-in.org;.
13.13 U.S. EPA. Cost Analyses for Selected
      Groundwater Cleanup Projects: Pump and 'JTreat
      Systems and Permeable Reactive Barriers, i
      Office of Solid Waste and Emergency Response.
      EPA-542-R-00-013. February  2001.  http:/i/clu-
      in.org.                                 I
13.14 DOE. Permeable Reactive Treatment (PeRT)
      Wall for Rads and Metals. Office of      j
      Environmental Management, Office ofScieJQ.ee
      and Technology. DOE/EM-0557.  September
      2000. http://apps.em.doe.gov/ost/pubs/itsrs/!
      itsr2155.pdf                           !
13.15 Attachment to an E-mail from Rick Wilkin,! U. S.
      EPA Region 8 to Linda Fiedler, U.S. EPA
      Technology Innovation Office.  July 27, 206l.
13.16 Lindberg J, Sterneland J, Johansson PO,   j
      Gustafsson JP. Spodic material for in situ
      treatment of arsenic in ground water. Ground
      Water Monitoring and Remediation.  17,125-3-.
      December 1997.
      http://www.ce.kth.se/aom/amov/people/gustafjp/
      absll.htm
13.17 Su, C.; Puls, R. W.  Arsenate and arsenite
      removal by zerovalent iron: kinetics, redox
      transformation, and implications for in situ
      groundwater remediation. Environmental  !
      Science and Technology.  Volume 35. pp. 1487-
      1492.  2001.                           :
3.18  Smyth D J, Blowes D W, Ptacek, C J (Department
      of Earth Sciences, University of Waterloo).',
      Steel Production Wastes for Use in Permeable
      Reactive Barriers (PRBs). Third International
      Conference on Remediation of Chlorinated tad
      Recalcitrant Compounds. May 20-23, 2000:.
      Monterey, CA.     '                    I
13.19 Personal Communication from David Smyth,
      University of Waterloo to Sankalpa Nagaraja,
      Tetra Tech, EM Inc. August 13, 2002.    ;
                                                 13-5

-------
                                                               Table 13.1
                                 Permeable Reactive Barrier Arsenic Treatment Performance Data for Arsenic
""Prefect"
Number
1
2
3
4
5
6
7
8
9
10
Scale ;
Full
Full
Full
Pilot
Pilot _
Bench
Bench
Bench
Bench
Bench
Site Name and Location :
Tonolli Corporation Superfund
Site, Nesquehoning, PA
Monticello Mill Tailings - OU3,
Monticello, UT
Industrial Site, Chicago, IL
Industrial Site, Northwestern
Ontario, Canada
_ Bodo_Canyon Disposal Cell
Mill Tailings Site, Durango, CO
Former Uranium Ore Processing
Site, Tuba City, AZ
Monticello Mill Tailings,
Monticello, UT
Asarco East Helena Plant, East
Helena, MT
-
—
I Initial iSenfe
Concentration (mg/L)j
0.313
0.010 - 0.013
—
0.4mg/L
—
0.52
0.024
11
l-3mg/L
4mg/L
Final Arsenic
Concentration (mg/L)
Not available
O.0002
-"
0.02 mg/L

0.010
0.001-0.008
Not available
<0.02 mg/L
<0.003 mg/L
• 	 ." ILJ IM"-" 	 I'"
Earner Type and
Media
Trench, limestone
Funnel and gate, ZVI
Trench, basic oxygen
furnace slag
Trench, mixture of
ZVI, surfactant
modified zeolite, and
ion exchange resin
ZVI_
ZVI
ZVI
ZVI
-
Basic oxygen furnace
slag
Project Duration
August 1998 -
present
June 1999 -
present
June 2002 -
present

—
—
—
—
--
—
I
Source
13.1, 13.7
13.1, 13.2,
13.14
13.19
13.19
13.12
13.3
13.3
13.15
13.16
13.18
ZVI = Zero valent iron
mg/L = Milligrams per liter
— = Not available
                                                                  13-6

-------
  ARSENIC
APPLICABLE TO
       IIC
TREATMENT TECHNOLOGIES
     SOIL, WASTE, AND WATER

-------

-------
 14.0     ELECTROKINETIC TREATMENT
         ARSENIC
  Summary

   Electrokinetic treatment is an emerging remediation
  technology designed to remove heavy metal
  contaminants from soil and groundwater.  The
  technology is most applicable to soil with small ;
  particle sizes, such as clay. However, its
  effectiveness may be limited by a variety of
  contaminants and soil and water characteristics. .
  Information sources researched for this report   i
  identified a limited number of applications of the
  technology to arsenic.                         ;
Technology Description and Principles         <

In situ electrokinetic treatment of arsenic uses the  •
natural conductivity of the soil (created by pore water
and dissolved salts) to affect movement of water, kins,
and particulates through the soil (Ref. 14.8).  Water
and/or chemical solutions can also be added to enhance
the recovery of metals by electrokinetics. Positively-
Technology Description: Electrokinetic
remediation is based on the theory that a low-
density current will mobilize contaminants in the
form of charged species.  A current passed between
electrodes is intended to cause water, ions, and
particulates to move through the soil, waste, and
water (Ref. 14.8). Contaminants arriving at the
electrodes can be removed by means of
electroplating or electrodeposition, precipitation or
coprecipitation, adsorption, complexing with ion
exchange resins, or by pumping of water (or other
fluid) near the electrode (Ref. 14.10).

Media Treated:
•    Soil
    Groundwater
ฐ    Industrial wastes

Chemicals Used in Electrokinetic Process to
Treat Arsenic:
ฐ    Sulfuric Acid
    Phosphoric Acid
•    Oxalic Acid
                               Model of an Electrokinetic Treatment System





^

Extraction/
Exchange
"
Processing

Process Control System

1 t
2S>__ _^




Extraction/
Exchange

i
Processing

t 1
~4 — i—*


LT-
       Acid Front
     and/or Anodic
     Process Fluid
                                                  14-1

-------
charged metal or metalloid cations, such as As (V) and
As (III) migrate to the negatively-charged electrode
(cathode), while metal or metalloid anions migrate to
the positively charged electrode (anode) (Ref. 14.9).
Extraction may occur at the electrodes or in an external
fluid cycling/extraction system (Ref. 14.11).       ;
Alternately, the metals can be stabilized in situ by
injecting stabilizing agents that react with and
immobilize the contaminants (Ref. 14.12). Arsenic has
been removed from soils treated by electrokinetics
using an external fluid cycling/extraction system (Ref.
14.2,14. L8).                                    '.

This technology can also be applied ex situ to
groundwater by passing the water between electrodes.
The current causes arsenic to migrate toward the
electrodes, and also alters the pH and oxidation-   r
reduction potential of the water, causing arsenic to •.
precipitate/coprecipitate.  The solids are then removed
from the water using clarification and filtration (Ref.
14.21).

Media and Contaminants Treated

Electrokinetic treatment is an in situ treatment process
that has had limited use to treat soil, groundwater, and
industrial wastes containing arsenic.  It has also been
used to treat other heavy metals such as zinc, cadmium,
mercury, chromium, and copper (Ref. 14.1,14.4,
14.20).

Electrokinetic treatment may be capable of removing
contaminants from both saturated and unsaturated soil
zones, and may be able to perform without the addition
of chemical or biological agents to the site.  This  ;
technology also may be applicable to low-permeability
soils, such as clay (Ref. 14.1,14.4, 14.9).

Type, Number, and Scale of Identified Projects
Treating Soil, Waste, and Water Containing Arsenic

The sources identified for this report contained
information on one full-scale, three pilot-scale, and
three bench-scale applications of electrokinetic    r
remediation to arsenic. Figure 14.1 shows the number
of applications identified at each scale.           ;

Summary of Performance Data

Table 14.1 provides a performance summary of
electrokinetic treatment of arsenic. One full-scale
application reduced arsenic concentrations in soil from
greater than 250 mg/kg to less than 30 mg/kg.  Onb ex
 situ pilot-scale application reduced arsenic in
 groundwater from 0.6 mg/L to 0.013 mg/L. The case
 study at the end of this section further discusses this
 Factors Affecting Electrokinetic Treatment
 Performance

     Contaminant properties - The applicability of
     electrokinetics to soil and water containing
     arsenic depends on the solubility of the
     particular arsenic species. Electrokinetic
     treatment is applicable to acid-soluble polar
     compounds, but not to insoluble metals (Ref.
     14.6).
     Salinity and  cation exchange  capacity - The
     technology is most efficient when these
     parameters are low (Ref. 14.14).  Chemical
     reduction of chloride ions at the anode by the
     electrokinetic process may also produce
     chlorine gas (Ref. 14.6).
 •   Soil moisture - Electrokinetic treatment
     requires adequate soil moisture; therefore
     addition of a  conducting pore fluid may be
     required (Ref. 14.7).  Electrokinetic treatment is
     most applicable to saturated soils (Ref. 14.9).
     However, adding fluid to allow treatment of
     soils without sufficient moisture may flush
     contaminants out of the targeted treatment area.
 •   Polarity and magnitude of the ionic charge -
     These factors affect the direction and rate of
     contaminant  movement (Ref. 14.11).
 •   Soil type - Electrokinetic treatment is most
     applicable to homogenous soils (Ref. 14.9).
     Fine-grained soils are more amenable to
     electrokinetic treatment due to their large
     surface area,  which provides numerous sites for
     reactions necessary for electrokinetic processes
     (Ref. 14.13).
 •   pH - The pH can affect process
     electrochemistry and cause precipitation of
     contaminants or other species, reducing soil
     permeability and inhibiting recovery. The
     deposition of precipitation solids may be
     prevented by flushing the cathode with water or
     a dilute acid  (Ref. 14.14).
project, and information in Table 14.1, Project 3
summarizes the available information about it.

Applicability, Advantages, and Potential Limitations

Electrokinetics is an emerging technology with
relatively few applications for arsenic treatment. It is
an in situ treatment technology, and therefore does not
require excavation of contaminated soil or pumping of
contaminated groundwater. Its effectiveness may be
limited by a variety of soil and contaminant
characteristics, as discussed in the box opposite. In
                                                    14-2

-------
 addition, its treatment depth is limited by the depth to
 which the electrodes can be placed.              i

                    Figure 14.1               |
      Scale of Electrokinetic Projects for Arsenic
                     Treatment               :
   Fun
  Pilot
 Bench
   Case Study:  The Overpelt Project

   A pilot-scale test of electrokinetic remediation of
   arsenic in groundwater was conducted in Belgium
   in 1997.  This ex situ application involved pumping
   groundwater contaminated with zinc, arsenic, and
   cadmium and treating it in an electrokinetic
   remediation system with a capacity of 6,600 gpm.
   The treatment system precipitated the
   contaminants, and the precipitated solids were
   removed using clarification and filtration.  The
   electrokinetic treatment system did not use
   additives  or chemicals.  The treatment reduced
   arsenic concentrations in groundwater from 0.6
   mg/L to 0.013 mg/L. The reported costs of the
   treatment were $0.004 per gallon for total  cost, and
   $0.002 per gallon for O&M. (Ref. 14.21)  (see
   Project 3, Table  14.1).
 Summary of Cost Data                        i
                                              i
 Estimated costs of in situ electrokinetic treatment of
 soils containing arsenic range from $50 - $270 per cy
 (Ref. 14.2,14.4, cost year not provided). The reported
 costs for one pilot-scale, ex situ treatment of      !
 groundwater of the treatment were $0.004 per gallon for
 total cost, and $0.002 per gallon for O&M.  (Ref. 14.21)
 (see Project 3, Table 14.1).                      \
  Factors Affecting Electrokinetic Treatment Costs

      Contaminant extraction system - Some
      electrokinetic systems remove the contaminant
      from the subsurface using an extraction fluid.,1
      In such systems, the extraction fluid may
      require further treatment, which can increase
      the cost (Ref. 14.4).                       :
  •    Factors affecting electrokinetic treatment
      performance - Items in the "Factors Affecting
      Electrokinetic Treatment Performance" box
      will also affect costs.                      '.
References                                    i
                                              I
                                              I
14.1  U.S. EPA. In Situ Remediation Technology:!
      Electrokinetics. Office of Solid Waste and  !
      Emergency Response, Technology Innovation
      Office. EPA-542-K-94-007.  April 1995.   I
      http://clu-in.org                          !
14.2  U.S. EPA.  Database for EPA REACH IT
      (REmediation And CHaracterization Innovative
      Technologies). March 2001.
      http://www.epareachit.org.
14.3  U.S. EPA.  Electrokinetics at an Active Power
      Substation. Federal Remediation Technologies
      Roundtable. March 2000.
      http://www.frtr.gov/costperf.html.
14.4  Electric Power Research Institute.  Electrokinetic
      Removal of Arsenic from Contaminated Soil:
      Experimental Evaluation. July 2000.
      http ://www.epri.com/
      OrderableitemDesc.asp?product_id.
14.5  Ground-Water Remediation Technologies
      Analysis Center. Technology Overview Report:
      Electrokinetics. July 1997.
      http://www.gwrtac.org/pdf/elctro_o.pdf.
14.6  U.S.  EPA.  Contaminants and Remedial Options
      at Selected Metal-Contaminated Sites. Office of
      Research and Development. EPA-540-R-95-
      512.  July 1995.
      http://www.epa.gov/ncepi/Catalog/
      EPA540R95512.html
14.7  U.S.  EPA. Recent Developments for In Situ
      Treatment of Metals Contaminated Soils.
      Technology Innovation Office.  Washington,
      DC.  March 5, 1997.
      http://clu-in.org/download/remed/metals2.pdf
14.8  Will, F. "Removing Toxic Substances from Soil
      Using Electrochemistry," Chemistry and
      Industry, p.  37'6-3''9. 1995.
                                                  14-3

-------
14.9  Evanko, C.R., and D.A. Dzomback.
      Remediation of Metals-Contaminated Soils and
      Ground\vater.  Prepared for the Ground-Water
      Remediation Technologies Analysis Center,
      Technology Evaluation Report TE-97-01.
      October 1997.
      http://www.gwrtac.org/pdfymetals.pdf
14.10 Lindgren, E.R., et al.  "Electrokinetic
      Remediation of Contaminated Soils: An Update,"
      Waste Management 92, Tucson, Arizona.  1992.
14.11 Earthvision. "Electrokinetic Remediation," '
      http://www.earthvision.net/filecomponent/ :
      1727.html, as of October 1999.
14.12 LaChuisa, L. E-mail attachment from Laurie
      LaChuisa, Electrokinetics, Inc., to Kate Mikulka,
      Science Applications International Corporation,
      Process description. August 1999.        |
14.13 Acar, Y. B. and R. J. Gale.  "Electrokinetic >
      Remediation: Basics and Technology Status,"
      Journal of Hazardous Materials, 40: p. 117-137.
      1995.
14.14 Van Cauwenberghe, L. Electrokinetics,
      prepared for the Ground-Water Remediation
      Technologies Analysis Center, GWRTAC 6
      Series Technology Overview Report TO-97|:03.
      July 1997.
      http://www.gwrtac.org/pdf/elctro_o.pdf
14.15 LaChuisa, L.  E-mail from Laurie LaChuisa,
      Electrokinetics, Inc., to Kate Mikulka, Science
      Applications International Corporation, Case
      study for electrokinetic extraction/stabilization of
      arsenic. August 1999.
14.16 LaChuisa, L.  E-mail from Laurie LaChuisa,
      Electrokinetics, Inc., to Deborah R. Raja,
      Science Applications International Corporation,
      Responses to questions on Case Study. October
      13, 1999.
14.17 LaChuisa, L.  Telephone contact between Laurie
      LaChuisa, Electrokinetics, Inc., and Deborah R.
      Raja, Science Applications International
      Corporation, Responses to questions on Case
      Study.  October 11, 1999.
14.18 AAA Geokinetics - Electrokinetic Remediation.
      April 24,2001.
      http://www.geokinetics.com/giiek.htm
14.19 Fabian, G.L., U.S. Army Environmental Center,
      and Dr. R.M. Bricka, Waterways Experiment
      Station. "Electrokinetic Remediation at NAWS
      Point Mugu," paper presented at the
      U.S./German Data Exchange Meeting.
      September 1999.
 14.20 Florida State University - College of
      Engineering.  August 2001.
      http://www.eng.fsu.edu/departments/civil/
      research/arsenicremedia/index.htm        '•
14.21  Pensaert, S. The Treatment of Aquifers
      Contaminated with Arsenic, Zinc and Cadmium
      by the Bipolar Electrolysis Technique:  The
      Overpelt Project. 1998.
14.22  Ribeiro, AB, Mateus EP, Ottosen LM, Bech-
      Nielsen G. Electrodialytic Removal of Cu, Cr,
      and As from Chromated Copper Arsenate-
      Treated Timber Waste. Environmental Science
      & Technology. Vol. 34, No. 5.  2000.
      http://www.vista.gov. vn/nganhangdulieu/tapchi/c
      Ivl899/2000/v34s5.htm
14.23  Redwine, J.C.  Innovative Technologies for
      Remediation of Arsenic in Soil and
      Groundwater.  Southern Co. Services, Inc.
      August 2001.
14.24 Markey, R. Comparison and Economic Analysis
      of Arsenic Remediation Methods Used in Soil
      and Groundwater. M.S. Thesis. FAMU-FSU
      College of Engineering. 2000.
                                                   14-4

-------
                                                                 Table 14.1
                                            Electrokinetic Treatment Performance Data for Arsenic
rroject
Number
1

3

4
5
6

Industry or
Site Type
Wood Preserving
Herbicide
application
Metals refining
and smelting

Herbicide
application
Cattle vat
(pesticide)
Cattle vat
(pesticide)
Wood Preserving
Waste or
Media, Volume
Soil, 325 cubic
yards
Soil, 690 cubic
yards
Groundwater

Soil &
Groundwater
Soil
Soil
Sawdust from
CCA-treated
pole
Scale
Full
Pilot
Pilot

Pilot
Bench
Bench
Bench
Site Name and
Location
Pederok Plant
Kwint,
Loppersum,
Netherlands

Belgium

Florida
Blackwater River
State Forest, FL
Blackwater River
State Forest, FL
Leiria, Portugal
Initial Arsenic
Concentration
> 250 mg/kg
450 mg/kg
0.6 mg/L

ND - 1,400
mg/kg
O.005 - 0.7
mg/L
113 mg/kg
1 13 mg/kg
81 1-871 mg/kg
Final Arsenic Concentration
or Treatment Results
< 30 mg/kg

0.013 mg/L


4.7% of arsenic migrated to
anode, 1.6% to cathode
25% of arsenic migrated to
anode, none to cathode
27-99% removal efficiency
Electrokinetic Process
Description
Contaminant removed
by recirculation of
electrolyte through
casing around electrodes

Bipolar electrolysis,
without use of
Ex situ, pump and treat
application
Bipolar electrolysis,
without use of
additional chemicals
Addition of sulfuric acid
to enhance
electrokinetic process
Addition of phosphoric
acid to enhance
electrokinetic process
Electrodialytic removal,
enhanced by addition of
oxalic acid
Source
14.2,
14.18
14.12,
14.15,
14.16,
14.17
14.21

14.24
14.4
14.4
14.22
~ = Not available
CCA = Chromated copper arsenate
mg/L = Milligrams per liter
mg/kg = Milligrams per kilogram
                                                                   14-5

-------

-------
  15.0    PHYTOREMEDIATION  TREATMENT
          OF ARSENIC                        i
    Summary

    Phytoremediation is an emerging technology. The
    data sources used for this report contained      ;
    information on only one applications of
    phytoremediation to treat arsenic at full scale and
    two at pilot scale. Experimental research into   ,
    identifying appropriate plant species for
    phytoremediation is ongoing.  It is generally    '•
    applicable only to shallow soil or relatively shallow
    groundwater that can be reached by plant roots. In
    addition, the phytoremediating plants may
    accumulate high levels of arsenic during the
    phytoremediation process, and may require
    additional treatment prior to disposal.
           Technology Description: Phytoremediation is
           designed to use plants to degrade, extract, contain,
           or immobilize contaminants in soil, sediment, or
           groundwater (Ref.  15.6).  Typically, trees with deep
           roots are applied to groundwater and other plants are
           used for shallow soil contamination.

           Media Treated:
           •   Soil
           •   Groundwater

           Types of Plants Used in Phytoremediation to
           Treat Arsenic:
           •   Poplar
           •   Cottonwood
           •   Sunflower
               Indian mustard
               Corn
                                                i
 Technology Description and Principles          i
                                                i
 Phytoremediation is an emerging technology generally
 applicable only to shallow contamination that can be
 reached by plant roots. Phytoremediation applies to all
 biological, chemical, and physical processes that are
 influenced by plants and the rhizosphere, and that aid in
 cleanup of the contaminated substances.           j
 Phytoremediation may be applied in situ or ex situ, to
 soils, sludges, sediments, other solids, or groundwater
 (Ref. 15.1, 15.4, 15.5, 15.7).  The mechanisms of  '
         Examples of vegetation used in phytoremediation
         include sunflower, Indian mustard, corn, and grasses
         (such as ryegrass and prairie grasses) (Ref. 15.1).  Some
         plant species, known as hyperaccumulators, absorb and
         concentrate contaminants within the plant at levels
         greater than the concentration in the surrounding soil or
         groundwater. The ratio of contaminant concentration in
         the plant to that in the surrounding soil or groundwater
         is known as the bioconcentration factor. A
         hyperaccumulating fern (Pteris vittatd) has been used in
         the remediation of arsenic-contaminated soil, waste, and
 v^.. IU.L, ij.-,, u.j, * j.,}.  me mecnanisms or   ,         me remediation of arsenic-contaminated soil, waste an<
 phytoremediation include phytoextraction (also kno^n as     water. The fern can tolerate as much as 1,500 parts'per
 phytoaccumulation, the uptake of contaminants by plant
 roots and the translocation/accumulation of contaminants
 into plant shoots and leaves), enhanced rhizosphere '
 biodegradation (takes place in soil or groundwater  \
 immediately surrounding plant roots), phytodegradation
 (metabolism of contaminants within plant tissues), and
 phytostabilization (production of chemical
 compounds by plants to immobilize
 contaminants at the interface of roots and
 soil). The data sources used for this report
 identified phytoremediation applications for
 arsenic using phytoextraction and
 phytostabilization.
The selection of the phytoremediating
species depends upon the species ability to
treat the contaminants and the depth of
contamination.  Plants with shallow roots
(for example, grasses, corn) are appropriate
only for contamination near the surface,
typically in shallow soil. Plants with deeper
roots, (for example, trees) may be capable of
remediating deeper contaminants in soil or
groundwater plumes.
         million (ppm) of arsenic in soil, and can have a
         bioconcentration factor up to 265. The arsenic
         concentration in the plant can be as high as 2 percent
         (dry weight) (Ref. 15.3, 15.6).
.Photosynthesis
               hloem  H20 +nutrients
              Photosynthesis + O2
                                    Transpiration
                                   JJark Respiration
Root! respiration
  CO +H2O2
         •v_^
 Mineralization"'
Organic
chemicals Uptake
                   CXHy OZ
                                         Uptake (and
                                         contaminant
                                         removal)
                                    Transpiration

                                      Degradation
            O2 + exduates
           -e.g.,CH3C OOH
                                                   15-1

-------
Media and Contaminants Treated

Phytoremediation has been applied to contaminants from
soil, surface water, groundwater, leachate, and municipal
and industrial wastewater (Ref. 15.4). In addition to,
arsenic, examples of pollutants it can potentially address
include petroleum hydrocarbons such as benzene,   \
toluene, ethylbenzene, and xylenes (BTEX), polycydic
aromatic hydrocarbons (PAHs), pentachlorophenol,  ;
polychlorinated biphenyls (PCBs), chlorinated aliphatics
(trichloroethylene, tetrachloroethylene, and 1,1,2,2-
tetrachloroethane), ammunition wastes (2,4,6-
trinitrotoluene or TNT, and RDX), metals (lead,    f
cadmium, zinc, arsenic, chromium, selenium), pesticide
wastes and runoff (atrazine, cyanazine, alachlor),
radionuclides (cesium-137, strontium-90, and uranium),
and nutrient wastes (ammonia, phosphate, and nitrate)
(Ref. 15.7).

Type, Number, and Scale of Identified Projects
Treating Soil, Waste, and Water Containing Arsenic

The data sources used for this report contained
information on phytoremediation of arsenic        ,
contaminated soil at full scale at one Superfund site (Ref.
 15.7). Two pilot-scale applications and four bench-scale
tests were also identified (Ref. 15.2, 15.3,15.7-11).
Figure 15.1 shows the number of identified applications
at each scale.

                     Figure  15.1
   Scale of Identified Phytoremediation Projects for
                  Arsenic Treatment
Full
'
Pilot
Bench
i
rr--.ii

jj 411*1 t ซii i
i
2
Jim
_
S=:
f
4
IT :. . :



i "i
0 1 2 3 ' i
 Summary of Performance Data

 Table 15.1 provides a performance summary of the;
 identified phytoremediation projects. Data on the effect
 of phytoremediation on the leachability of arsenic from
 soil were not identified. Where available, Table 15.1
 provides total arsenic concentrations prior to and
following phytoremediation treatment.  However, no
projects with arsenic concentrations in the treated soil,
waste, and water both prior to and after treatment were
identified. Bioconcentration factors were available for
one pilot- and two bench-scale studies, and ranged from
8 to 320.

Applicability, Advantages, and Potential Limitations

Phytoremediation is conducted in situ and therefore
does not require soil excavation.  In addition,
revegetation for the purpose of phytoremediation also
can enhance restoration of an ecosystem (Ref. 15.5).
This technology is best applied at sites with shallow
contamination. If phytostabilization is used, the
vegetation and soil may require long-term maintenance
to prevent re-release of the contaminants. Plant uptake
and translocation of metals to the aboveground portions
of the plant may introduce them into the food chain if
the plants are consumed (Ref. 15.5). Products could
bioaccumulate in animals that ingest the plants (Ref.
 15.4).  In addition, the toxicity and bioavailability of
contaminants absorbed by plants and phytodegradation
products is not always known.

Concentrations of contaminants in hyperaccumulating
plants are limited to a maximum of about 3% of the
   Factors Affecting Phytoremediation
   Performance

       Contaminant depth - The treatment depth is
       limited to the depth of the plant root system
       (Ref. 15.5).
       Contaminant concentration - Sites with; low
       to medium level contamination within the root
       zone are the best candidates for
       phytoremediation processes (Ref. 15.4,15.5).
       High contaminant concentrations may be toxic
       to the remediating flora.
       Climatic or seasonal conditions - Climatic
       conditions may interfere or inhibit plant
       growth, slow remediation efforts, or increase
       the length of the treatment period (Ref. 15.4).
       Contaminant form - In phytoaccumulation
       processes, contaminants are removed from the
       aqueous or dissolved phase.
       Phytoaccumulation is generally not effective on
       contaminants that are insoluble or strongly
       bound to soil particles.
       Agricultural factors -  Factors that affect plant
       growth and health, such as the presence of
       weeds and pests, and ensuring that plants
       receive sufficient water and nutrients will affect
       phytoremediation processes.
                                                     15-2

-------
plant weight on a dry weight basis. Based on this ;
limitation, for fast-growing plants, the maximum annual
contaminant removal is about 400 kg/hectare/year.'
However, many hyperaccumulating species do not!
achieve contaminant concentrations of 3%, and are! slow
growing. (Ref. 15.12)                          I

The case study at the end of this section further dispusses
an application of phytoremediation to the treatment to
arsenic-contaminated soil. Information for this project is
summarized in Table 15.1, Project 1.             j
                                             i
Summary of Cost Data                        I
                                             i
Cost data specific to phytoremediation of arsenic Were
not identified. The estimated 30-year costs (1998 j
dollars) for remediating a 12-acre lead site were   j
$200,000 for phytoextraction (Ref. 15.15). Costs ^ere
estimated to be $60,000 to $ 100,000 using        ;
phytoextraction for remediation of one acre of    ;
20-inch-thick sandy loam (Ref. 15.14). The cost of
removing radionuclides from water with sun-flowers has
been estimated to be $2 to $6 per thousand gallons pf
water (Ref. 15.16).  Phytostabilization system costs have
been estimated at $200 to $ 10,000 per hectare,    '
equivalent to $0.02 to $1.00 per cubic meter of soilj,
assuming a 1-meter root depth (Ref. 15.17).       ,
                                             i
References
                                             i
15.1   U.S. EPA. Treatment Technologies for Sitei
      Cleanup: Annual Status Report (Tenth Edition).
      Office of Solid Waste and Emergency Response.
      EPA-542-R-01-004.  February 2001.       j
      http://www.epa.gov/ncepi/Catalog/        i
      EPA542R01004.html                    i
15.2   Cost and Performance Case Study.         j
      Phytoremediation at Twin Cities Army     j
      Ammunition Plant Minneapolis-St.Paul,    ',
      Minnesota. Federal Remediation Technologies
      Roundtable (FRTR).                     |
      http://www.frtr.gov/costperf.htm.
15.3   Ma LQ, Komar KM, Tu C, Zhang WH, Cai V,
      Kennelly ED. A fern that hyperaccumulates
      arsenic. Nature 409:579. February 2001.   |
      http://www.ifas.ufl.edu/~qma/PUBLICATlON/
      Nature.pdf                             !
15.4   Federal Remediation Technologies Screening
      Matrix and Reference Guide Version 3.0. FRTR.
      http://www.frtr.gov/matrix2/topjpage.html !
15.5   U.S. EPA.  Introduction to Phytoremediation.
      National Risk Management Research       !
      Laboratories.  Office of Research and       !
      Development. EPA 600-R-99-107. February
      2000. http://www.clu-in.org/download/remed/
      introphyto.pdf                          j
  Factors Affecting Phytoremediation Costs

  •   Number of crops grown - A greater number
      of crops may decrease the time taken for
      contaminants to be remediated to specified
      goals, thereby decreasing costs (Ref. 15.2).
      However, the number of crops grown will be
      limited by the length of the growing season, the
      time needed for crops to reach maturity, the
      potential for multiple crops to deplete the soil
      of nutrients,  climatic conditions, and other
      factors.
  •   Factors affecting phytoremediation
      performance - Items in the "Factors Affecting
      Phytoremediation Performance" box will also
      affect costs.
15.6  Zhang W, Cai Y, Tu C, Ma LQ. Speciation and
      Distribution of Arsenic in an Arsenic
      Hyperaccumulating Plant.  Biogeochemistry of
      Environmentally Important Elements. Symposia
      Papers Presented Before the Division of
      Environmental Chemistry. American Chemical
      Society. San Diego, CA. April 1-5, 2001.
15.7  SchnoorJL. Phytoremediation. Technology
      Evaluation Report.  Prepared for Ground-Water
      Remediation Technologies Analysis Center
      (GWRTAC).  1997.
      http://www.gwrtac.org/html/
      tech_eval.html#PHYTO
15.8  U.S. EPA. Phytoremediation Resource Guide.
      Office of Solid Waste and Emergency Response.
      EPA 542-B-99-003.  June 1999.
      http://www.clu-in.org/download/remed/
      phytoresguide.pdf
15.9  Compton A, Foust RD, Salt DA, Ketterer ME.
      Arsenic Accumulation in Potomogeton
      illinoiensis in Montezuma Well, Arizona.
      Biogeochemistry of Environmentally Important
      Elements. Symposia Papers Presented Before
      the Division of Environmental Chemistry.
      American Chemical Society. San Diego, CA.
      April 1-5, 2001.
15.10 RedwineJC. Innovative Technologies for
      Remediation of Arsenic in Soil and
      Groundwater.  Southern Company Services, Inc.
15.11 Qian JH, Zayed A, Zhu YL, Yu M, Terry N.
      Phytoaccumulation of Trace Elements by
      Wetland Plants:  III.  Uptake and Accumulation
      of Ten Trace Elements by Twelve Plant Species.
      Journal of Environmental Quality.  1999.
15.12 Lasat, M. The Use of Plants for the Removal of
      Toxic Metals from Contaminated Soil.
      American Association for the Advancement of
      Science.
                                                  15-3

-------
15.13 Lasat, M. Phytoextraction of Toxic Metals: A
      review of Biological Mechanisms. J. of Environ.
      Qual. 31:109-120. 2002.
15.14 Salt, D. E., M. et al. Phytoremediation: A Novel
      Strategy for the Removal of Toxic Metals from
      the Environment Using Plants. Biotechnol.
      13:468-474.  1995.
15.15 Cunningham, S. D. The Phytoremediation of Soils
      Contaminated with Organic Pollutants: Problems
      and Promise. International Phytoremediation
      Conference. May 8-10. Arlington, VA. 1996.;
15.16 Dushenkov, S., D. et al.. Removal of Uranium
      from Water Using Terrestrial Plants. Environ, Sci.
      Technol. 31(12):3468-3474.  1997.
15.17 Cunningham, S. D., and W. R. Berti, and J. W.
      Huang. Phytoremediation of Contaminated Soils.
      Trends Biotechnol. 13:393-397.  1995.
                                                  15-4

-------
                         Table 15.1
Arsenic Phytoremediation Treatment Performance Data for Arsenic
Project
Number
1
2
3

4

5
6
7
Industry or Site
Type
Mining
Munitions
Manufacturing/S
torage




Wood
Preserving


Waste or
Media
Deep soil
Surface soil
Groundwater
(ex situ)

Surface soil

Surface soil
Soil
Soil
Scale
Full
Pilot
Pilot

Bench

Bench
Bench
Bench
Site Name or
Location
Whitewood Creek
Superfund Site, SD
Twin Cities Army
Ammunition Plant, Site
C and Site 129-3,
Minneapolis-St. Paul,
MN
Montezuma Well, AZ

—

FL
East Palo Alto, CA

Initial Arsenic
Concentration
1,000 mg/kg

100 mg/L (Well
water)

650
™
400


Final Arsenic
Concentration
Performance data
not available due
to death of
remediating flora.

4.59 mg/kg
(shoots)
8 87 mg/kg-
(roots)
—

—

34 mg/kg
(shoots)
177 mg/kg (roots)
Bioconcentration
Factor


8

20 - 75 (leaves)
60 - 320 (shoots)
265


Remediating
Flora
Hybrid poplar
(specific
variety not
identified)
Corn (specific
variety not
identified),
white mustard
(Sinapis alba)
Potomogeton
illinoiensis

Moss verbena
(V. tenuisectd)
Saw palmetto
(S. repens)
Brake fern
(Pteris vittatd)
Tamarisk
(Tamarix
ramosissimd),
Eucalyptus
Water lettuce
(Pistia
stratiotes)
Source
15.7
15.2
15.9

15.10

15.3
15.8
15.11
                           15-5

-------

-------
 16.0    BIOLOGICAL TREATMENT FOR  |
         ARSENIC
  Summary

  Biological treatment designed to remove arsenic
  from soil, waste, and water is an emerging     >
  remediation technology. The information sources .
  used for this report identified a limited number of
  projects treating arsenic biologically.  Arsenic was
  reduced to below 0.050 mg/L in one pilot-scale
  application. This technology promotes
  precipitation/coprecipitation  of arsenic in water or
  leaching of arsenic in soil and waste.  The leachate
  from bioleaching requires additional treatment for
  arsenic prior to disposal.                      ;
Technology Description and Principles        !
                                              i
Although biological treatments have usually been l
applied to the degradation of organic contaminants,
some innovative techniques have applied biological
remediation to the treatment of arsenic. This     !
technology involves biological activity that promotes
precipitation/coprecipitation of arsenic from water 'and
leaching of arsenic in soil and waste.            i

Biological precipitation/coprecipitation processesfdxr
water create ambient conditions intended to cause i
arsenic to precipitate/coprecipitate or act directly oil
arsenic species to transform them into species that &re
more amenable to precipitation/coprecipitation. Trie
microbes may be suspended in the water or attached to
a submerged solid substrate.  Iron or hydrogen sulfide
may also be added (Ref. 16.2, 16.3, 16.4, 16.4).   '
 Technology Description: Biological treatment of
 arsenic is based on the theory that microorganisms
 that act directly on arsenic species or create ambient
 conditions that cause arsenic to precipitate/     •
 coprecipitate from water and leach from soil and
 waste.

 Media Treated:
 •   Soil
 •   Waste                                   :
     Water                                   :

 Microbes Used:
 •   Sulfate-reducing bacteria
 •   Arsenic-reducing bacteria
 One water treatment process depends upon biological
 activity to produce and deposit iron oxides within a
 filter media, which provides a large surface area over
 which the arsenic can contact the iron oxides. The
 aqueous solution is passed through the filter, where
 arsenic is removed from solution through
 coprecipitation or adsorption to the iron oxides. An
 arsenic sludge is continuously produced (Ref. 16.3).
       Model of a Biological Treatment System
                     Influent
                     Packed
                    media and
                     microbes
                     Effluent
Another process uses anaerobic sulfate-reducing
bacteria and other direct arsenic-reducing bacteria to
precipitate arsenic from solution as insoluble arsenic-
sulfide complexes (Ref. 16.2). The water containing
arsenic is typically pumped through a packed-bed
column reactor, where precipitates accumulate until the
column becomes saturated (Ref. 16.5).  The arsenic is
then stripped and the column is biologically regenerated
(Ref. 16.2). Hydrogen sulfide has also been used in
suspended reactors to biologically precipitate arsenic
out of solution (Ref.  16.2, 16.4).  These reactors require
conventional solid/liquid  separation techniques for
removing precipitates.

Removal of arsenic from  soil biologically via
"accelerated bioleaching" has also been tested on a
bench scale.  The microbes in this system produce
nitric, sulfuric, and organic acids which are intended to
mobilize and remove arsenic from ores and sediments
(Ref. 16.4). This biological activity also produces
surfactants, which can enhance metal leaching (Ref.
16.4).

Media and Contaminants Treated

Biological treatment typically uses microorganisms to
degrade organic contaminants in soil, sludge, solids
groundwater, and wastewaters. Biological treatment
                                                  16-1

-------
has also been used to treat arsenic in water via
precipitation/coprecipitation and in soil through
leaching (Ref. 16.1,16.3).                       ;

Type, Number, and Scale of Identified Projects
Treating Soil, Waste, and Water Containing Arsenic

The data sources used for this report contained    ;
information on biological treatment of arsenic at full
scale at one facility, at pilot scale at three facilities,; and
at bench scale for one project. Figure  16.1 shows the
number of identified applications at each scale. An
enhanced bioleaching system for treating soil      !
containing arsenic has been tested at bench scale (Ref.
16.4) (Table 16.1, Project 5). In addition, a biological
treatment system using hydrogen sulfide has been used
in a bioslurry reactor to treat arsenic at bench and pilot
scales (Ref. 16.4) (Table 16.1, Project  4).

                    Figure 16.1                r
Scale of Identified Biological Treatment Projects for
                      Arsenic
   Fun
  Pilot
 Bench
!
!
t. jjji
^^W ~^ — TY^^T--
I
\
, • 	 i|ilHI 111 "I
.Hi i jllbt i i* N i
jtiijllillllli j||3;ฐl iiili 11 1


--T- '-

1
Summary of Performance Data

Table 16.1 lists the available performance data for'three
projects using biological treatment for arsenic
contamination in water. Of the two projects that treated
wastewaters containing arsenic, only one had bothi
influent and effluent arsenic concentration data (Project
 1). The arsenic concentration was not reduced to below
0.05 mg/L in this project.

One project (Project 3) treated groundwater spiked with
sodium arsenite.  The groundwater had naturally- :
occurring iron at 8 - 12 mg/L (Ref. 16.3). The initial
arsenic concentration ranged from 0.075 to 0.400 mg/L,
and was reduced by treatment to less than 0.050 mg/L.
No data were available for the one soil bioleaching
project.
 Factors Affecting Biological Treatment
 Performance

     pH - pH levels can inhibit microbial growth.
     For example, sulfate-reducing bacteria perform
     optimally in a pH range of 6.5 to 8.0 (Ref.
     16.5).
 •   Contaminant concentration - High arsenic
     concentrations may be toxic to microorganisms
     used in biological treatment (Ref. 16.1).
     Available nutrients - An adequate nutrient
     supply should be available to the microbes to
     enhance and stimulate growth. If the initial
     solution is nutrient deficient, nutrient addition
     may be necessary.
     Temperature - Lower temperatures decrease
     biodegradation rates. Heating may be required
     to maintain biological activity (Ref. 16.1).
 •   Iron concentration - For biologically-
     enhanced iron precipitation, iron must be
     present in the water to be treated. The optimal
     iron level depends primarily on the arsenic
     concentration. (Ref. 16.3).
The case study at the end of this section further
discusses a pilot-scale application of biological ;
treatment to arsenic-contaminated groundwater.
Information for this project is summarized in Table
16.1, Project 3.

Applicability, Advantages, and Potential Limitations

A variety of arsenic-contaminated soil, waste, and water
can be treated using biological processes.  Biological
treatment of arsenic may produce less sludge than
conventional  ferric arsenic precipitation (Ref. 16.2). A
high concentration of arsenic could inhibit biological
activity (Ref. 16.1, 16.2).
  Factors Affecting Biological Treatment Costs

  •   Pretreatment requirements - Pretreatment
      may be required to encourage the growth of key
      microorganisms.  Pretreatment can include pH
      adjustment and removal of contaminants that
      may inhibit microbial growth.
      Nutrient addition - If nutrient addition is
      required, costs may increase.
  •   Factors  affecting biological treatment
      performance - Items in the "Factors Affecting
      Biological Treatment Performance"  box will
      also affect costs.
                                                    16-2

-------
Summary of Cost Data                       '

The reported costs for biological treatment of arsenic-
contaminated soil, waste, and water range from less
than $0.50 to $2.00 per 1,000 gallons (Ref. 16.2, 1)5.4,
cost year not provided).                        ;

References

16.1  Remediation Technologies Reference Guide and
      Screening Manual, Version 3.0. Federal   •
      Remediation Technologies Roundtable.    I
      http://www.frtr.gov/matrix2/top_page.html.',
16.2  Applied Biosciences. June 28, 2001.       ;
      http://www.bioprocess.com               i
16.3  Use of Biological Processes for Arsenic    i
      Removal. June 28, 2001.                 !
      http://www.saur.co.uk/poster.html         ;
16.4  Center for Bioremediation at Weber State  !
      University.  Arsenic Treatment Technologies.
      August 27, 2001. http://www.weber.edu/
      Bioremediation/arsenic.htm
16.5  Tenny, Ron and Jack Adams. Ferric Salts  '
      Reduce Arsenic in Mine Effluent by Combining
      Chemical and Biological Treatment. August 27,
      2001. http://www.esemag.eom/0101/ferric.hmil
Case Study:  Sodium Arsenite Spiked
Groundwater, Forest Row, Sussex, United
Kingdom

Groundwater with naturally-occurring iron between
8 and 12 mg/L was extracted in Forest Row,
Sussex, England and spiked with sodium arsenite.
The arsenic concentration before treatment ranged
from 0.075 to 0.400 mg/L in the untreated water.
The spiked groundwater was passed through a pilot
biological filtration unit, 3 m high with a 15 cm
diameter and filled to 1 m with silica sand. The
arsenic concentration was reduced to <0.04 mg/L
(Ref. 16.3) (see Project 3, Table 16.1).
                                                16-3

-------
                                                               Table 16.1
                                            Biological Treatment Performance Data for Arsenic
Project
Number
1
2
3 -
4
5
——_ — , ,„,,,
Industry or
Site Type





Waste or Media
Wastewater
Wastewater
Groundwater
spiked with
sodium arsenite
Groundwater
Ores and
sediments
Scale
Full
Pilot
-Pilot
Pilot
Bench
SiteNarne
or Location





Initial Arsenic
Concentration

13mg/L
0.075-0.400
mg/L


Final Arsenic
Concentration
O.05 mg/L
<0.5 mg/L
0.010-0.040
mg/L


Precipitate
Arsenic
Concentration





Biological Process
Reduction and
precipitation from sulfate
reducing bacteria and
direct arsenic-reducing
bacteria
Anaerobic sulfate-
reducing bacteria with a
two-stage reactor, arsenic
precipitation and column
system
Biological filtration where
microbial activity
produces iron oxides for
coprecipitation or
adsorption of arsenic
Precipitation of arsenic
sulfides using hydrogen
sulfide in a bioreactor
system
Enhanced bioleaching
system using microbial-
generated acids to
accelerate anion and
cation removal from ores
and sediments
Source
16.2
16.1
16.3
16.4
16.4
mg/L = Milligram per liter
— = Not available
                                                                  16-4

-------
                              Appendix A
                               \
                        Literature Search Results

          This appendix does not appear in the printed version of
Arsenic Treatment Technologies for Soil, Waste, and Water. This appendix is
   available in the on-line version of this report at http://clu-in.org/arsenic.

-------

-------
                    Appendix B




Superfund Sites with Arsenic as a Constituent of Concern

-------

-------
                      Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern
REGION
01
01
01
1 67"
101
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
ol
oT~
01
01
01
STATE
CT
CT
CT
CT
CT
CT
MA
MA
MA
MA
MA
MA
MA
MA
MA
MA
MA
MA
MA
ME
ME
ME
ME
ME
NH
NH
NH
NH
NH
NH
NH
NH
NH
NH
NH
NH
NH
RI
RI
SITE NAME
LINEMASTER SWITCH; CORP.
GALLUP'S QUARRY !
LAUREL PARK, INC. !
OLD SOUTHINGTON LANDFILL
NEW LONDON SUBMARINE BASE
CHESHIRE GROUND WATER
OTIS AIR NATIONAL GUARD
FORT DEVENS :
SILRESIM CHEMICAL CORP.
W.R. GRACE & CO., INC. (ACTON
PLANT) i
BAIRD & MCGUIRE j
CHARLES-GEORGE RECLAMATION
TRUST LANDFILL i
IRON HORSE PARK ;
INDUSTRI-PLEX !
SALEM ACRES ;
PSC RESOURCES '
GROVELAND WELLS !
HOCOMONCO POND :
NYANZA CHEMICAL WASTE DUMP
BRUNSWICK NAVAL AIR STATION
LORING AIR FORCE BASE
UNION CHEMICAL CO.j INC.
WINTHROP LANDFILL i
i
SACO TANNERY WASTE PITS
PEASE AIR FORCE BASE
FLETCHER'S PAINT WOJRKS &
STORAGE I
NEW HAMPSHIRE PLATING CO.
COAKLEY LANDFILL :
KEEFE ENVIRONMENTAL SERVICES
KES) i
YLVESTER i
MOTTOLO PIG FARM i
DOVER MUNICIPAL LANDFILL
AUBURN ROAD LANDFILL
AVAGE MUNICIPAL WATER SUPPLY
TOWN GARAGE/RADIO iBEACON
IIBBETTS ROAD ;
OTTATI & GOSS/KINGSTON STEEL
DRUM i
DAVISVILLE NAVAL CONSTRUCTION
ATTALION CENTER !
NEWPORT NAVAL EDUCATION &
RAINING CENTER •
EPA ID
CTDOO 11 53923
CTD 108960972
CTD980521165
CTD980670806
CTD980906515
CTD98 10673 17
MA2570024487
MA72 10025 154
MAD000192393
MADOO 1002252
MADOO 104 1987
MAD003809266
MAD05 1787323
MAD076580950
MAD980525240
MAD980731483
MAD980732317
MAD980732341
MAD990685422
ME8 1700220 18
ME9570024522
MED042143883
MED980504435
MED980520241
NH7570024847
NHDOO 1079649
NHD001091453
NHD064424153
NHD092059112
SJHD099363541
^1)980503361
VIHD980520191
•v[HD980524086
SIHD980671002
SHD981063860
^0989090469
NHD9907 17647
RI6170022036
RI6 170085470
APPLIED
—
—
—
—
—
—
—
—
SOLIDIFICATION/
STABILIZATION
PRECIPITATION/
COPRECIPITATION,
ADSORPTION
II
—
—

SOLIDIFICATION/
STABILIZATION
__
	
—
	
—
	
PRECIPITATION/
COPRECIPITATION
—
	
~
	
	
--

	
	
	
	
	
	
-
~
—
                      B-l

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
EPA
REGION
01
01
01
01
01
01
01
01
01
01
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
STATE
RI
RI
RI
RI
VT
VT
VT
VT
VT
VT
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
SITE NAME
ETERSON/PURITAN, INC.
CENTRAL LANDFILL
)AVIS (GSR) LANDFILL
)AVIS LIQUID WASTE '>.-.
'ANSITOR ELECTRONICS, INC.
BURGESS BROTHERS LANDFILL
BFI SANITARY LANDFILL
ROCKINGHAM)
>INE STREET CANAL :
>ARKER SANITARY LANDFILL
BENNINGTON MUNICIPAL SANITARY
LANDFILL
NAVAL WEAPONS STATION EARLE
SITE A) :
'ICATINNY ARSENAL (USARMY)
sTAVAL AIR ENGINEERING CENTER
CHEMICAL CONTROL
)AYCO CORP./L.E CARPENTER CO.
AMERICAN CYANAMID CO.
1ERCULES, INC. (GIBBSTOWN PLANT)
SHIELDALLOY CORP. i
VINELAND CHEMICAL CO., INC.
:URCIO SCRAP METAL, INC.
SWOPE OIL & CHEMICAL CO.
'RIED INDUSTRIES
CHEMICAL LEAMAN TANK LINES,
INC.

-------
                        i   Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
REGION
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
STATE
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NJ
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY-
NY
SITE NAME
CHEMSOL, INC. |
ELLIS PROPERTY i
FLORENCE LAND RECONTOURING,
INC., LANDFILL i
D'IMPERIO PROPERTY;
RINGWOOD MINES/LANDFILL
SPENCE FARM :
FRIEDMAN PROPERTY;
IMPERIAL OIL CO., INC./CHAMPION
CHEMICALS i
DOVER MUNICIPAL WELL 4
ROCKY HILL MUNICIPAL WELL
MONTGOMERY TOWNSHIP HOUSING
DEVELOPMENT ;
MYERS PROPERTY
ROCKAWAY TOWNSHIP WELLS
EWAN PROPERTY
DE REWAL CHEMICALi CO.
CINNAMISON TOWNSHIP (BLOCK 702)
GROUND WATER CONTAMINATION
INDUSTRIAL LATEX CORP.
HIGGINS FARM
PLATTSBURGH AIR FORCE BASE
SYOSSET LANDFILL i
RAMAPO LANDFILL i
POLLUTION ABATEMENT SERVICES
YORK OIL CO. 1
FMC CORP. (DUBLIN ROAD
LANDFILL) ;
MATTIACE PETROCHEMICAL CO.,
INC. ;
NIAGARA COUNTY REFUSE
LOVE CANAL i
CLAREMONT POLYCHBMICAL
GENZALE PLATING COi
AMERICAN THERMOSTAT CO.
ROBINTECH, ESfC./NATIpNAL PIPE CO
HOOKER CHEMICAL & PLASTICS
CORP./RUCO POLYMER! CORP.
CARROLL & DUBIES SEWAGE
DISPOSAL
ACET ENTERPRISES, INC.
OLVENT SAVERS
WARWICK LANDFILL i
HOOKER (102ND STREET)
SLIP MUNICIPAL SANITARY
ANDFILL
OHNSTOWN CITY LANDFILL
IDNEY LANDFILL ;
EPA ID
NJD980528889
NJD980529085
NJD980529143
NJD980529416
NJD980529739
NJD980532816
NJD980532832
NJD980654099
NJD980654131
NJD980654156
NJD980654164
NJD980654198
NJD980654214
NJD980761365
NJD980761373
NJD980785638
NJD981 178411
NJD98 1490261
NY457 1924774
NYD0005 11360
NYD000511493
NYD000511659
NYD000511733
NYD000511857
NYD0005 12459
NYD0005 14257
NYD000606947
hJYD002044584
NTYD002050110
STYD002066330
SIYD002232957
NYD002920312
NYDO 109680 14
MYD073675514
>4YD98042 11 76
^YD980506679
S4YD980506810
NYD980506901
v[YD980506927

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
EPA
REGION
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
03
03
03
03
03
03
03
03
03
03
03
03
STATE
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
NY
PR
PR
VI
DE
DE
DE
MD
MD
MD
MD
MD
MD
MD
MD
PA
SITE NAME
ATAVIA LANDFILL
RICHARDSON HILL ROAD
LANDFILL/POND !
VOLNEY MUNICIPAL LANDFILL
:ORTESE LANDFILL '
DLEAN WELL FIELD
ONES SANITATION r
ARNEY FARM
SEALAND RESTORATION, INC.
SINCLAIR REFINERY ,
APPLIED ENVIRONMENTAL SERVICES
'ULTON TERMINALS
CENTUCKY AVENUE WELL FIELD
>ORT WASHINGTON LANDFILL
NIAGARA MOHAWK POWER CORP.
SARATOGA SPRINGS PLANT)
^TORTH SEA MUNICIPAL LANDFILL
JEC TRUCKING !
'REFERRED PLATING CORP.
iNDICOTT VILLAGE WELL FIELD
ffiRTEL LANDFILL :
:iRCUITRON CORP.
ROWE INDUSTRIES GRQUND WATER
CONTAMINATION '
FOREST GLEN MOBILEJHOME
SUBDIVISION ;
GCL TIE AND TREATING INC.
ROSEN BROTHERS SCRAP
YARD/DUMP !
PASLEY SOLVENTS & CHEMICALS,
INC. •
rUNCOS LANDFILL i
'IBERS PUBLIC SUPPLY WELLS
TUTU WELLFIELD •,
DOVER AIR FORCE BASE
WILDCAT LANDFILL !
HALBY CHEMICAL CO;
ABERDEEN PROVING GROUND
(EDGEWOOD AREA) |
ABERDEEN PROVING GROUND
(MICHAELSVILLE LANDFILL)
PATUXENT RIVER NAVAL AIR
STATION
MID-ATLANTIC WOOD PRESERVERS,
INC. h
WOODLAWN COUNTY1 LANDFILL
LIMESTONE ROAD
SAND, GRAVEL AND STONE
KANE & LOMBARD STREET DRUMS
LETTERKENNY ARMY; DEPOT (PDO
AREA) !
EPA ID

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
EPA
REGION
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
STATE
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
PA
VA
VA
VA
VA
VA
VA
VA
VA
VA
SITE NAME V
TOBYHANNA ARMY DEPOT
NAVAL AIR DEVELOPMENT CENTER
(8 WASTE AREAS) i
STRASBURG LANDFILL
HAVERTOWNPCP
WHITMOYER LABORATORIES
i
1
1
DRAKE CHEMICAL !
TONOLLI CORP.
1
NOVAK SANITARY LANDFILL
OCCIDENTAL CHEMICAL
CORP./FIRESTONE Tire & RUBBER CO.
MILL CREEK DUMP
LORD-SHOPE LANDFILL
MIDDLETOWN AIR FIELD
WADE (ABM) :
BRODHEAD CREEK !
OLD CITY OF YORK LANDFILL
TAYLOR BOROUGH DUMP
BELL LANDFILL
MCADOO ASSOCIATES
OSBORNE LANDFILL ;
LINDANE DUMP i
WALSH LANDFILL [
YORK COUNTY SOLID WASTE AND
REFUSE AUTHORITY LANDFILL
RODALE MANUFACTURING CO., INC.
MARINE CORPS COMBAT
DEVELOPMENT COMMAND
DEFENSE GENERAL SliJPPLY CENTER
(DLA) ;
NAVAL SURFACE WARFARE CENTER -
DAHLGREN >
NAVAL WEAPONS STATION -
YORKTOWN i
SAUNDERS SUPPLY CO.
GREENWOOD CHEMICAL CO.
i
C & R BATTERY CO., INC.
AVTEX FIBERS, INC. ,
RENTOKIL, INC. (VIRGINIA WOOD
PRESERVING DIVISION)
EPA ID
PA5213820892
PA6170024545
PAD000441337
PAD002338010
PAD003005014
PAD003058047
PAD073613663
PAD079 160842
PAD980229298
PAD980231690
PAD980508931
PAD980538763
PAD980539407
PAD980691760
PAD980692420
PAD980693907
PAD980705107
PAD980712616
PAD9807 12673
PAD9807 12798
PAD980829527
PAD980830715
PAD98 1033285
VA1 170024722
VA397 1520751
VA7 170024684
VA8170024170
VAD003117389
VAD003 125374
VAD049957913
VAD070358684
VAD071040752
TECHNOLOGY
APPLIED
—
—
—
—
SOLIDIFICATION/
STABILIZATION,
PRECIPITATION/
COPRECIPITATION
—
SOLIDIFICATION/
STABILIZATION,
PERMEABLE REACTIVE
BARRIER
—
—
—
--
--
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PRECIPITATION/
COPRECIPITATION,
ADSORPTION
PRECIPITATION/
COPRECIPITATION,
ADSORPTION
—
—
—
                             B-5

-------
                           Table B.I
Superfund Sites with Arsenic^as a Contaminant of Concern (continued)
EPA
REGION
03
03
03
03
03
03
03
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
STATE
VA
VA
VA
VA
VA
WV
WV
AL
AL
AL
AL
AL
AL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
FL
SITE NAME
FIRST PIEDMONT CORP: ROCK
QUARRY (ROUTE 719)
U.S. TITANIUM
CHISMAN CREEK
RHINEHART TIRE FIRE DUMP
ATLANTIC WOOD INDUSTRIES, INC.
ALLEGANY BALLISTICS
LABORATORY (USNAVY)
ORDNANCE WORKS DISPOSAL AREAS
ALABAMA ARMY AMMUNITION
PLANT !
CIBA-GEIGY CORP. (MCfNTOSH
PLANT)
T.H. AGRICULTURE & NUTRITION CO.
(MONTGOMERY PLANT)
OLIN CORP. (MCINTOSH PLANT)
INTERSTATE LEAD CO. (ILCO)
REDWING CARRIERS, INC.
(SARALAND) '
CECIL FIELD NAVAL AIR STATION
JACKSONVILLE NAVAL AIR STATION
i
HOMESTEAD AIR FORCE BASE
i
PENSACOLA NAVAL AIR STATION
REEVES SOUTHEASTERN
GALVANIZING CORP.
PEAK OIL CO./BAY DRUM CO.
STAUFFER CHEMICAL CO (TAMPA)
I
!
AMERICAN CREOSOTE WORKS, INC.
(PENSACOLA PLANT) !
STAUFFER CHEMICAL CO. (TARPON
SPRINGS) [
ANACONDA ALUMINUM CO./MILGO
ELECTRONICS CORP. t
PEPPER STEEL & ALLOYS, INC.
SHERWOOD MEDICAL INDUSTRIES
ZELLWOOD GROUND WATER
CONTAMINATION 1
BMI-TEXTRON ;
HELENA CHEMICAL CQ. (TAMPA
PLANT) i
SCHUYLKILL METALS CORP.
MIAMI DRUM SERVICES
MUNISPORT LANDFILL;
AGRICO CHEMICAL CO;
PICKETTVILLE ROAD LANDFILL
EPA ID
VAD980554984
VAD980705404
VAD980712913
VAD980831796
VAD990710410
WV0170023691
WVD000850404
AL62 10020008
ALDOO 122 1902
ALD007454085
ALD008 188708
ALD04 1906 173
ALD980844385
FL5 170022474
FL6170024412
FL7570024037
FL9 170024567
FLD000824896
FLD004091807
FLD004092532
FLD008161994
FLDO 105960 13
FLD020536538
FLD032544587
FLD043861392
FLD049985302
FLD052 172954
FLD053502696
FLD062794003
FLD076027820
FLD084535442
FLD980221857
FLD980556351
TECHNOLOGY
APPLIED
SOLIDIFICATION/
STABILIZATION
—
—
„
—
i
—
;
—
—
—
~
'
—
SOLIDIFICATION/
STABILIZATION
SOLIDIFICATION/
STABILIZATION
—
—
-
SOLIDIFICATION/
STABILIZATION
—
—
—
—
—
—
!
—
-
--
-
SOLIDIFICATION/
STABILIZATION
;
                              B-i

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
REGION
04
04
04
04
04
04
04
04
04
04
04
04
04
05
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
STATE
FL
FL
FL
FL
FL
FL
FL
FL
FL
GA
GA
GA
GA
GA
GA
GA
GA
KY
KY
KY
KY
KY
KY
KY
KY
KY
KY
MS
NC
NC
NC
NC
NC
NC
NC
SITE NAME
DAVIE LANDFILL ,
NORTHWEST 58TH STREET LANDFILL
WHITEHOUSE OIL PITS
SAPP BATTERY SALVAGE
CABOT/KOPPERS
KASSAUF-KIMERLING BATTERY
DISPOSAL
SIXTY-SECOND STREET DUMP
ANODYNE, INC. j
WINGATE ROAD MUNICIPAL
INCINERATOR DUMP
ROBINS AIR FORCE BASE (LANDFILL
#4/SLUDGE LAGOON) !
MONSANTO CORP. (AUGUSTA PLANT)
WOOLFOLK CHEMICAL WORKS, INC.
T.H. AGRICULTURE & NUTRITION CO.
(ALBANY PLANT) !
NATIONAL SMELTING! & REFINING
CO. INC. i
CEDARTOWN INDUSTRIES, INC.
CEDARTOWN MUNICIPAL LANDFILL
HERCULES 009 LANDFILL
PADUCAH GASEOUS DIFFUSION
PLANT (USDOE) :
NATIONAL SOUTHWIRE ALUMINUM
CO.
BRANTLEY LANDFILL,'
GREEN RIVER DISPOSAL, INC.
HOWE VALLEY LANDFILL
LEE'S LANE LANDFILL!
DISTLER BRICKYARD i
MAXEY FLATS NUCLEAR DISPOSAL
FORT HARTFORD COAL CO. STONE
QUARRY !
NEWPORT DUMP ;
NEWSOM BROTHERS/OLD
REICHHOLD CHEMICAtS, INC.
CAMP LEJEUNE MILITARY RES.
(USNAVY) I
CAPE FEAR WOOD PRESERVING
PCX, INC. (STATESVILLE PLANT)
NORTH CAROLINA STATE
UNIVERSITY (LOT 86, FARM UNIT #1)
ADCO-HUGHES FACILITY
CHARLES MACON LAGOON AND
DRUM STORAGE !
ABERDEEN PESTICIDE DUMPS
EPA ID
FLD980602288
FLD980602643
FLD980602767
FLD980602882
FLD980709356
FLD980727820
FLD980728877
FLD981014368
FLD98 102 1470
GA1 570024330
GADOO 1700699
GAD003269578
GAD042101261
GAD057302002
GAD095840674
GAD980495402
GAD980556906
KY8890008982
KYD049062375
KYD980501019
KYD980501076
KYD980501191
KYD980557052
KYD980602155
KYD980729107
KYD980844625
KYD985066380
MSD980840045
NC6170022580
NCD003 188828
NCD095458527
NCD980557656
NCD980729602
NCD980840409
NCD980843346
TECHNOLOGY
APPLIED
SOLIDIFICATION/
STABILIZATION
—
—
—
SOLIDIFICATION/
STABILIZATION
--
—
—
—
—
—
—
--
PYROMETALLURGICAI
RECOVERY
—
—
—
—
—
—
—
—
—
—
—
—
—
-
--
—
—
—
—
—
—
                            B-7

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
E1>A
REGION
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
STATE
NC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
SC
TN
TN
TN
TN
TN
TN
TN
TN
TN
IL
IL
IL
IL
IL
IL
IL
IL
IL
IL
IL
IN
IN
IN
IN
SITE NAME
NATIONAL STARCH & CHEMICAL
CORP. :
SAVANNAH RIVER SITE (USDOE)
BEAUNIT CORP. (CIRCULAR KMT &
DYEING PLANT)
'ARA-CHEM SOUTHERN, INC.
SANGAMO WESTON, INC./TWELVE-
MILE CREEK/LAKE HARTWELL
PCB CONTAMINATION '
SHURON INC. i
PALMETTO WOOD PRESERVING
1
KOPPERS CO., INC. (CHARLESTON
PLANT) I
LEXINGTON COUNTY LANDFILL
AREA
SCRDI DIXIANA
GOLDEN STRIP SEPTIC TANK SERVICE
ELMORE WASTE DISPOSAL
VIILAN ARMY AMMUNITION PLANT
OAK RIDGE RESERVATION (USDOE)
MEMPHIS DEFENSE DEPOT (DLA)
AMERICAN CREOSOTE WORKS, INC.
(JACKSON PLANT) i
ROSS METALS INC.
ARLINGTON BLENDING &
PACKAGING !
MORTH HOLLYWOOD DUMP
GALLAWAYPITS i
WRIGLEY CHARCOAL PLANT
PARSONS CASKET HARDWARE CO.
JOHNS-MANVILLE CORP.
OUTBOARD MARINE WAUKEGAN
COKE PLANT '
BYRON SALVAGE YARD
WAUCONDA SAND & GRAVEL
ACME SOLVENT RECLAIMING, INC.
(MORRISTOWN PLANT)
YEOMAN CREEK LANDFILL
H.O.D. LANDFILL ;
WOODSTOCK MUNICIPAL LANDFILL
PAGEL'S PIT ;
ADAMS COUNTY QUINCY LANDFILLS
2&3 :
REILLY TAR & CHEMICAL CORP.
(INDIANAPOLIS PLANT)
CONTINENTAL STEEL CORP.
AMERICAN CHEMICAL SERVICE, INC.
WAYNE WASTE OIL !
EPA ID
NCD99 1278953
SC1890008989
SCD000447268
SCD002601656
SCD003354412
SCD003357589
SCD003362217
SCD9803 10239
SCD980558043
SCD980711394
SCD980799456
SCD980839542
TN02 10020582
TNI 890090003
TN4210020570
TND0070 18799
TND096070396
TND980468557
TND980558894
TND980728992
TND980844781
ILD005252432
ILD005443544
ILD000802827
ILD010236230
ILD0470 19732
ILD0532 19259
ILD980500102
ILD980605836
ILD980605943
ILD980606685
ILD980607055
IND000807107
IND001213503
INDO 163 60265
IND048989479
APPLIED
"
—
~— ;
—

—
SOLIDIFICATION/
STABILIZATION
""*
""*"
—
—
—
--
—
—
~~
SOLIDIFICATION/
STABILIZATION
__
--
—
--
--
:
SOLIDIFICATION/
STABILIZATION
—
—
SOLIDIFICATION/
STABILIZATION
•
—
—
--
~
"
—
—
—
                              B-!

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
EPA
REGION
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
STATE
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
MI
SITE NAME : '
NORTHSIDE SANITARY LANDFILL,
INC !
LAKELAND DISPOSAL, 'SERVICE, INC.
LAKE SANDY JO (M&M LANDFILL)
WASTE, INC., LANDFILL
DOUGLASS ROAD/UNIROYAL, INC.,
LANDFILL
MIDCO I !
FORT WAYNE REDUCTION DUMP
MIDCO II :
MAIN STREET WELL FIELD
MARION (BRAGG) Dim/IP
TIPPECANOE SANITARY LANDFILL,
INC. ;
WHITEFORD SALES & SERVICE
INC./NATIONALEASE '
KENTWOOD LANDFILL
BERLIN & FARRO :
MICHIGAN DISPOSAL SERVICE (CORK
STREET LANDFILL) !
ANDERSON DEVELOPMENT CO.
ELECTROVOICE !
BENDIX CORP./ALLIED AUTOMOTIVE
NORTH BRONSON INDUSTRIAL AREA
PETOSKEY MUNICIPAL WELL FIELD
ROCKWELL INTERNATIONAL CORP.
(ALLEGAN PLANT) :
PEERLESS PLATING CO.
ADAM'S PLATING I
H. BROWN CO., INC. ;
THERMO-CHEM, INC. !
OTT/STORY/CORDOVA[CHEMICAL CO.
BUTTERWORTH #2 LANDFILL
SOUTH MACOMB DISPOSAL
AUTHORITY (LANDFILLS #9 AND #9 A)
CARTER INDUSTRIALS; INC.
FOREST WASTE PRODUCTS
G&H LANDFILL ;
PARSONS CHEMICAL WORKS, INC.
CHEM CENTRAL
ROSE TOWNSHIP DUMP
SPRINGFIELD TOWNSHIP DUMP
ALBION-SHERIDAN TO^jiVNSHIP
LANDFILL
METAMORA LANDFILL:
FOLKERTSMA REFUSE •
J & L LANDFILL
CANNELTON INDUSTRIES, INC.
WASH KING LAUNDRY!
EPA ID
IND050530872
IND064703200
IND980500524
IND980504005
IND980607881
IND980615421
IND980679542
IND980679559
IND980794358
IND980794366
IND980997639
IND980999791
MID000260281
MID000605717
MID000775957
MID002931228
MID005068143
MID005 107222
MID005480900
MID0060 13049
MID006028062
MID006031348
MID006522791
MID017075136
MID044567162
MID060 174240
MID062222997
MID069826170
MID980274179
MID980410740
MID980410823
MID980476907
MID980477079
MID980499842
MID980499966
MID980504450
MID980506562
MID980609366
MID980609440
MID980678627
MID980701247
TECHNOLOGY
APPLIED
—
—
~
—
—
•
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
VITRIFICATION
—
—
SOLIDIFICATION/
STABILIZATION
—
—
—
—
~
—
                            B-9

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
EPA
REGION
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
STATE
MI
MI
MI
MI
MI
MI
MI
MI
MN
MN
MN
MN
MN
MN
MN
MN
MN
MN
MN
MN
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
SITE NAME
VICTOR WHEEL, INC.
VERONA WELL FIELD
AUTO ION CHEMICALS, INC.
VIASON COUNTY LANDFILL
CEMETERY DUMP
TORCH LAKE :
LOWER ECORSE CREEK DUMP
ORGANIC CHEMICALS, INC.
NEW BRIGHTON/ARDEN HILLS/TCAAP
(USARMY)
TWIN CITIES AIR FORCE RESERVE
BASE (SMALL ARMS RANGE
LANDFILL) ;
DINE BEND SANITARY LANDFILL
MACGILLIS & GIBBS CO./BELL
LUMBER & POLE CO.
WINDOM DUMP
PERHAM ARSENIC SITE
SOUTH ANDOVER SITE
VIORRIS ARSENIC DUMP
OAK GROVE SANITARY LANDFILL
WAITE PARK WELLS :
LAGRAND SANITARY LANDFILL
DAKHUE SANITARY LANDFILL
FERNALD ENVIRONMENTAL
MANAGEMENT PROJECT (FORMERLY
FEED MATERIALS PRODUCTION
CENTER (USDOE)) :
WRIGHT-PATTERSON AIR FORCE
BASE
POWELL ROAD LANDFILL
ORMET CORP.
ARCANUM IRON & METAL
UNITED SCRAP LEAD CO., INC.
ALLIED CHEMICAL & IRONTON COKE
ALSCO ANACONDA
LASKIN/POPLAR OIL CO.
SKINNER LANDFILL
SOUTH POINT PLANT
CHEM-DYNE
PRISTINE, INC.
SANITARY LANDFILL CO.
(INDUSTRIAL WASTE DISPOSAL CO.,
INC.)
BUCKEYE RECLAMATION
E.H. SCHILLING LANDFILL
OLD MILL
EPA ID
MID980702989
MID980793806
MID980794382
MID980794465
MID980794663
MID980901946
MID985574227
MID990858003
MN7213820908
MN8570024275
MND000245795
MND006 192694
MND980034516
MND980609572
MND980609614
MND980792287
MND980904056
MND98 1002249
MND98 1090483
MND98 1191 570
OH6890008976
OH7571724312
OHD000382663
OHD004379970
OHD017506171
OHD018392928
OHD043730217
OHD057243610
OHD061722211
OHD063963714
OHD07 1650592
OHD074727793
OHD076773712
OHD093895787
OHD980509657
OHD980509947
OHD9805 10200
1 JSCHJNOLOtrY
APPLIED
-
--
SOLIDIFICATION/
STABILIZATION
—
—
—
—
;
PHYTOREMEDIATION

—
SOLIDIFICATION/
STABILIZATION
'
--
—
-
~
—
—
—
SOLIDIFICATION/
STABILIZATION
—
—
VITRIFICATION, SOIL
FLUSHING
~
—
—
—
-
-
--
-
--

—
SOLIDIFICATION/
STABILIZATION
—
                             B-10

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
REGION
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
05
06
06
06
06
06
06
06
06
06
06
06
06
06
06
STATE
OH
OH
OH
OH
OH
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
WI
AR
AR
AR
AR
AR
LA
LA
LA
LA
LA
LA
NM
NM
NM
SITE NAME
SUMMIT NATIONAL >
FIELDS BROOK !
ZANESVILLE WELL FIELD
VAN DALE JUNKYARD
FULTZ LANDFILL
JANESVILLE ASH BEDS
KOHLER CO. LANDFILL
OCONOMOWOC ELECTROPLATING
CO., INC. !
PENTA WOOD PRODUCTS
NATIONAL PRESTO INDUSTRIES, INC.
LEMBERGER TRANSPORT &
RECYCLING I
MADISON METROPOLITAN
SEWERAGE DISTRICT LAGOONS
N.W. MAUTHE CO., ING.
HUNTS DISPOSAL LANDFILL
HAGEN FARM i
SAUK COUNTY LANDFILL
ALGOMA MUNICIPAL LANDFILL
WHEELER PIT i
CITY DISPOSAL CORP. LANDFILL
JANESVILLE OLD LANDFILL
MASTER DISPOSAL SERVICE
LANDFILL
ONALASKA MUNICIPAL LANDFILL
LEMBERGER LANDFILL, INC.
SPICKLER LANDFILL !
BETTER BRITE PLATING CO. CHROME
AND ZINC SHOPS
MID-SOUTH WOOD PRODUCTS
CECIL LINDSEY '.
NDUSTRIAL WASTE CONTROL
SOUTH 8TH STREET LANDFILL
MONROE AUTO EQUIPMENT CO.
PARAGOULD PIT) '
SOUTHERN SHIPBUILDING
CLEVE REBER !
PAB OIL & CHEMICAL SERVICE, INC.
I
GULF COAST VACUUMiSERVICES
i
D.L. MUD, INC. i
LINCOLN CREOSOTE \
UNITED NUCLEAR CORP.
CAL WEST METALS (USSBA)
SOUTH VALLEY i
EPA ID
OHD980609994
OHD9806 14572
OHD980794598
OHD980794606
OHD980794630
WID000712950
WID006073225
WID006100275
WID006 176945
WID006196174
WID056247208
WID078934403
WID083290981
WID980511919
WID980610059
WID980610141
WID980610380
WID9806 10620
WID9806 10646
WID9806 14044
WID980820070
WID980821656
WID980901243
WID980902969
WIT560010118
ARD092916188
ARD980496186
ARD980496368
ARD980496723
ARD980864110
LAD008149015
LAD980501456
LAD980749139
LAD980750137
LAD981058019
LAD98 1060429
^MD030443303
SIMD097960272
VFMD980745558
APPLIED
—
_
—
—
—
—
_
—
—
—
—
—
—
—
—
—
—
~
—
—
—
—
—
—
--
ADSORPTION,
SOLIDIFICATION/
STABILIZATION
—
—
—
—
—
SOLIDIFICATION/
STABILIZATION
SOLIDIFICATION/
STABILIZATION
SOLIDIFICATION/
STABILIZATION
—
—
—
—
—
                            B-ll

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
t^A
REGION
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
06
07
07
07
07
07
07
07
07
07
07
07
07
07
STATE
NM
NM
OK
OK
OK
OK
OK
OK
OK
TX
TX
TX
TX
TX
TX
TX
TX
TX
TX
TX
TX
TX
TX
IA
IA
IA
IA
IA
IA
IA
IA
IA
IA
IA
IA
IA
SITE NAME
CIMARRON MINING CORP.
CLEVELAND MILL
NATIONAL ZINC CORP.
DOUBLE EAGLE REFINERY CO.
OKLAHOMA REFINING;CO.
VfOSLEY ROAD SANITARY LANDFILL
TENTH STREET DUMP/JUNKYARD
FOURTH STREET ABANDONED
REFINERY i
SAND SPRINGS PETROCHEMICAL
COMPLEX i
LONGHORN ARMY AMMUNITION
PLANT ,
TEX-TIN
SHERIDAN DISPOSAL SERVICES
ISR CORPORATION
BIO-ECOLOGY SYSTEMS, INC.
FRENCH, LTD.
HIGHLANDS ACID PIT
KOPPERS CO., INC. (TEXARKANA
PLANT) !,
VIOTCO, INC.
SOUTH CAVALCADE STREET
BAILEY WASTE DISPOSAL
CRYSTAL CITY AIRPORT
NORTH CAVALCADE STREET
CRYSTAL CHEMICAL CO.
IOWA ARMY AMMUNITION PLANT
LAWRENCE TODTZ FARM
LEHIGH PORTLAND CEMENT CO.
JOHN DEERE (OTTUMWA WORKS
LANDFILLS) \
WHITE FARM EQUIPMENT CO. DUMP
MIDWEST MANUFACTURING/NORTH
FARM
MID-AMERICA TANNING CO.
VOGEL PAINT & WAX CO.
SHAW AVENUE DUMP
RED OAK CITY LANDFILL
E.I. DU PONT DE NEMOURS & CO.,
INC. (COUNTY ROAD X23)
NORTHWESTERN STATES PORTLAND
CEMENT CO. "
FAIRFIELD COAL GASIFICATION
PLANT
EPA ID
NMD980749378
NMD98 11 55930
OKD000829440
OKD007188717
OKD09 1598870
OKD980620868
OKD980620967
OKD980696470
OKD980748446
TX6213820529
TXD062113329
TXD062132147
TXD079348397
TXD980340889
TXD980514814
TXD9805 14996
TXD980623904
TXD980629851
TXD980810386
TXD980864649
TXD980864763
TXD980873343
TXD990707010
IA7213820445
IAD000606038
IAD005288634
IAD005291182
IAD065210734
IAD069625655
IAD085824688
IAD980630487
IAD980630560
IAD980632509
LAD980685804
IAD980852461
IAD981 124167
APPLIED
~
—
—
—
: SOLIDIFICATION/
STABILIZATION
—
—

;
~ |
PRECIPITATION/
COPRECIPITATION
~
—
SOLIDIFICATION/
STABILIZATION
SOLIDIFICATION/
STABILIZATION
—
~
—
~
—
—
ADSORPTION
—
;
;
—

~
"
:
—
SOLIDIFICATION/
STABILIZATION
—
" !
~™
"
                              B-12

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
REGION
07
07
07
07
07
07
07
07
07
07
07
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
08
STATE
IA
KS
KS
MO
MO
MO
MO
MO
NE
NE
NE
CO
CO
CO
CO
CO
CO
CO
CO
CO
CO
CO
CO
CO
MT
MT
MT
MT
MT
MT
ND
ND
SD
SD
SD
UT
UT
SITE NAME . ' " • -
MCGRAW EDISON SITE
FORT RILEY
PESTER REFINERY CO.'
WELDON SPRING !
QUARRY/PLANT/PITS (USDOE/ARMY)
CONSERVATION CHEMICAL CO.
KEM-PEST LABORATORIES
ST. LOUIS AIRPORT/HAZELWOOD
INTERIM STORAGE/FUTURA
COATINGS CO. ;
BEE CEE MANUFACTURING CO.
CORNHUSKER ARMY AMMUNITION
PLANT
HASTINGS GROUND WATER
CONTAMINATION
10TH STREET SITE ;
ROCKY MOUNTAIN ARSENAL
(USARMY) :
BRODERICK WOOD PRQDUCTS
MARTIN MARIETTA (DENVER
AEROSPACE)
ASARCO, INC. (GLOBE PLANT)
EAGLE MINE j
LOWRY LANDFILL
WOODBURY CHEMICAL CO.
DENVER RADIUM SITE ;
CENTRAL CITY, CLEAR CREEK
CALIFORNIA GULCH
SAND CREEK INDUSTRIAL
SMELTERTOWN SITE i
SUMMITVILLE MINE i
EAST HELENA SITE i
MONTANA POLE AND TREATING
ANACONDA CO. SMELTER
I
LIBBY GROUND WATER
CONTAMINATION
SILVER BOW CREEK/BUTTE AREA
MILLTOWN RESERVOIR SEDIMENTS
ARSENIC TRIOXIDE SITE
MINOT LANDFILL
ELLSWORTH AIR FORCE BASE
WILLIAMS PIPE LINE CO. DISPOSAL
IT
WHITEWOOD CREEK
ACOBS SMELTER
HILL AIR FORCE BASE (
EPA ID
IAD981711989
KS6214020756
KSD000829846
MO32 10090004
MOD000829705
MOD980631113
MOD980633176
MOD980860522
NE2213820234
NED980862668
NED981713837
CO52 10020769
COD000110254
COD001704790
COD007063530
COD081961518
COD980499248
COD980667075
COD9807 16955
COD980717557
COD980717938
COD9807 17953
COD983769738
COD983778432
MTD006230346
MTD006230635
MTD093291656
MTD980502736
MTD980502777
VITD9807 17565
^09807 16963
^TDD980959548
SD2571924644
SDD000823559
SDD980717136
UT0002391472
LJT0571724350
APPLIED
__
—
—
—
—
—
~~
—
—
—
—
SOLIDIFICATION/
STABILIZATION
SOLIDIFICATION/
STABILIZATION
—
	
—

—
—
—

—
—

—
—
SOLIDIFICATION/
STABILIZATION
—
PRECIPITATION/
COPRECIPITATION

—
—
—
—
—
SOLIDIFICATION/
STABILIZATION

                           B-13

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
EPA
REGION
08
08
08
08
08
08
08
08
08
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
STATE
UT
UT
UT
UT
UT
UT
UT
WY
WY
AZ
AZ
AZ
AZ
AZ
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
SITE NAME
MONTICELLO MILL TAILINGS
USDOE) :
DGDEN DEFENSE DEPOT (DLA)
VIIDVALE SLAG
PETROCHEM RECYCLING
CORP./EKOTEK PLANT I
PORTLAND CEMENT (KILN DUST 2 &
)
SHARON STEEL CORP. (MIDVALE
TAILINGS)
MURRAY SMELTER t
'.E. WARREN AIR FORCE BASE
BAXTER/UNION PACIFIC TIE
TREATING !
WILLIAMS AIR FORCE BASE
APACHE POWDER CO. r
JTCHFIELD AIRPORT AREA
NDIAN BEND WASH AREA
TUCSON INTERNATIONAL AIRPORT
AREA i
SACRAMENTO ARMY DEPOT
TREASURE ISLAND NAVAL STATION-
HUNTERS Point ANNEX
CAMP PENDLETON MARINE CORPS
BASE ;
MCCLELLAN AIR FORCE BASE
(GROUND WATER CONTAMINATION)
TRACY DEFENSE DEPOT (USARMY)
EL TORO MARINE CORPS AIR
STATION
?ORT ORD
BARSTOW MARINE CORPS LOGISTICS
BASE '
SHARPE ARMY DEPOT
MATHER AIR FORCE BASE (AC&W
DISPOSAL SITE)
J.H. BAXTER & CO.
KOPPERS CO., INC. (ORQVILLE
PLANT) i
RAYTHEON CORP.
LORENTZ BARREL & DRUM CO.
SELMA TREATING CO:
ADVANCED MICRO DEVICES, INC.
HEXCEL CORP.
INTEL CORP. (MOUNTAIN VIEW
PLANT) i
COAST WOOD PRESERVING
EPA ID
UT3890090035
UT92 10020922
UTD08 1834277
UTD093 119196
UTD9807 18670
UTD980951388
UTD980951420
WY5571924179
WYD061 112470
AZ7570028582
AZD008399263
AZD980695902
AZD980695969
AZD980737530
CA0210020780
CA1 170090087
CA2170023533
CA4570024337
CA497 1520834
CA6 170023208
CA72 10020676
CAS 170024261
CA82 10020832
CA8570024143
CAD000625731
CAD0091 12087
CAD009205097
CAD029295706
CAD029452141
CAD048634059
CAD058783952
CAD06 16202 17
CAD0630 15887
APPLIED
PERMEABLE REACTIVE
BARRIER
—
:
"
"
-
~
~

—
—
—
—
:
SOLIDIFICATION/
STABILIZATION
"
SOIL WASHING

:
" 1
—
"
—

SOLIDIFICATION/
STABILIZATION

—
--
SOLIDIFICATION/
STABILIZATION
—
—
:
—
                              B-14

-------
                           Table B.I
Superfund Sites with Arsenic as a Contaminant of Concern (continued)
REGION
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
09
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
STATE
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
GU
NV
AK
AK
AK
AK
ID
ID
ID
ID
ID
ID
ID
OR
OR
OR
OR
OR
OR
OR
WA
SITE NAME
VALLEY WOOD PRESERVING, INC.
LOUISIANA-PACIFIC CpRP.
SIGNETICS, INC. :
FAIRCHILD SEMICONDUCTOR CORP.
(MOUNTAIN VIEW PLANT)
IRON MOUNTAIN MINE
MCCOLL i
PACIFIC COAST PIPE LINES
CELTOR CHEMICAL WORKS
PURITY OIL SALES, INC.
HEWLETT-PACKARD (620-640 PAGE
MILL ROAD) i
WASTE DISPOSAL, INC!
WESTERN PACIFIC RAILROAD CO.
SAN FERNANDO VALLEY (AREA 2)
RHONE-POULENC, INC./ZOECON
CORP. ;
j
OPERATING INDUSTRIES, INC.,
LANDFILL i
ANDERSEN AIR FORCE ^BASE
CARSON RIVER MERCURY SITE
EIELSON AIR FORCE BASE
ADAK NAVAL AIR STATION
FORT WAINWRIGHT ;
ELMENDORF AIR FORCE BASE
IDAHO NATIONAL ENGINEERING
LABORATORY (USDOEJ
KERR-MCGEE CHEMICAL CORP.
SODA SPRINGS PLANT)
BUNKER HILL MINING &
METALLURGICAL COMPLEX
UNION PACIFIC RAILROAD CO.
MONSANTO CHEMICAL CO. (SODA
SPRINGS PLANT)
PACIFIC HIDE & FUR RECYCLING CO.
EASTERN MICHAUD FLATS
CONTAMINATION !
UMATILLA ARMY DEPOT (LAGOONS)
MCCORMICK & BAXTER CREOSOTING
CO. (PORTLAND PLANT)
UNION PACIFIC RAILROAD CO. TIE-
TREATING PLANT ;
TELEDYNE WAH CHANG
MARTIN-MARIETTA ALUMINUM CO.
OSEPH FOREST PRODUCTS
GOULD, INC.
NAVAL UNDERSEA WARFARE
ENGINEERING STATION (4 WASTE
AREAS) :
EPA ED
CAD063020143
CAD065021594
CAD070466479
CAD095989778
CAD980498612
CAD980498695
CAD980636781
CAD980638860
CAD980736151
CAD980884209
CAD980884357
CAD980894679
CAD980894901
CAT000611350
CAT0800 12024
GU6571999519
NVD980813646
AK1 570028646
AK4 170024323
AK62 10022426
AK8570028649
ID4890008952
IDD0413 10707
IDD048340921
IDD055030852
IDD08 1830994
IDD0988 12878
IDD984666610
OR6213820917
ORD009020603
ORD009049412
DRD050955848
3RD052221025
3RD068782820
DRD095003687
WAI 170023419
TECHNOLOGY
APPLIED


—
-
	
—
—
—
—
—
—

—
VITRIFICATION,
SOLIDIFICATION/
STABILIZATION
~
—
	

—
—
—
—
—
—
—
—

-
—
ADSORPTION, ION
EXCHANGE
—
—
—
—
—
"
                           B-15

-------
                                               Table B.I
                   Superfund Sites with Arsenic as a Contaminant of Concern (continued)
E1ปA
REGION
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
STATE
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
WA
SITE NAME
BONNEVILLE POWER
ADMINISTRATION ROSS COMPLEX
(USDOE)
PUGET SOUND NAVAL LSHIPYARD
COMPLEX ;
IANFORD 3 00- AREA (USDOE)
iANFORD 100-AREA (USDOE)
PORT HADLOCK DETACHMENT
(USNAVY)
IANFORD 1 100-AREA (USDOE)
3ANGOR NAVAL SUBMARINE BASE
NAVAL AIR STATION, WHIDBEY
ISLAND (AULT FIELD)
NAVAL AIR STATION, WHIDBEY
ISLAND (SEAPLANE BASE)
?ORT LEWIS LOGISTICS CENTER
WYCKOFF CO./EAGLE HARBOR
PACIFIC CAR AND FOUNDRY
WESTERN PROCESSING CO., INC.
YAKIMA PLATING CO.
QUEEN CITY FARMS ,
TULALIP LANDFILL
SILVER MOUNTAIN MINE
HARBOR ISLAND (LEAD)
TOFTDAHL DRUMS ,
COMMENCEMENT BAY, SOUTH
TACOMA CHANNEL
COMMENCEMENT BAY, NEAR
SHORE/TIDE FLATS
AMERICAN LAKE i.
EPA ID
WA1891406349
WA2170023418
WA2890090077
WAS 890090076
WA4170090001
WA4890090075
WAS 170027291
WAS 170090059
WA6170090058
WA72 10090067
WAD009248295
WAD009249210
WAD009487513
WAD040187890
WAD980511745
WAD980639256
WAD980722789
WAD980722839
WAD980723506
WAD980726301
WAD980726368
WAD980833065
APPLIED

,
—
—

;
—


—
SOLIDIFICATION/
STABILIZATION
SOLIDIFICATION/
STABILIZATION
--
~
—
—
—
--
.
SOLIDIFICATION/
STABILIZATION
.

— = Not available
                                                  B-16

-------

-------
                                        Solid Waste
                                        and Emergency Response
                                        (5102G)
EPA-542-R-02-004
September 2002
www.epa.gov/tio
clu-in.org/arsenic
United States
Environmental Protection Agency
(5102G)
Washington, D.C. 20460

Official Business
Penalty for Private Use $300
EPA-542-R-02-004

-------