United States
Environmental Protection
Agency
Office of Air Quality
Planning and Standards
Research Triangle Park NC 27711
EPA-450/4-81 -009
February 1981
Air
The Comprehensive Data
Handling System (CDHS)
Coding Manual
-------
EPA-450/4-81-009
The Comprehensive Data
Handling System
(CDHS)
Coding Manual
by
Larry R. McMaster, Project Leader
Research Triangle Institute
Research Triangle Park, NC 27709
Contract No. 68-02-3011
EPA Project Officer: Sam Colon-Velez
Prepared for
U.S. ENVIRONMENTAL PROTECTION AGENCY
Office of Air, Noise, and Radiation
Office of Air Quality Planning and Standards
Research Triangle Park, North Carolina 27711
February 1981
-------
This report is issued by trie" Environmental' Protection Agency to report:
technical data of interest to a limited number of readers . Copies? are
available free of charge to Federal employees, current contractors' and
grantees, and nonprofit organizations - in limited quantities. - from the
Library Services Office (MD-35), U.S. Environmental Protection Agency,
Research Triangle Park, North Carolina 27711; or for a. nominal fee,
from the National Technical Information Service., 5285 Port Royal Road,
Springfield, Virginia 22161.
This report was furnished to the Environmental Protection. Agency by
Research Triangle Institute, Research Triangle Park, North Carolina
27709, in fulfillment of Contract No. 68-02-30X1. The contents of this
report are reproduced herein as received from, Research Triangle-
Institute . The opinions, findings, and conclusions expressed are
those of the author and not necessarily those of the Environmental
Protection Agency. Mention of company or1 product names is* not to be
considered as an endorsement by the Environmental- Protection Agency.
-------
Table of Contents
List of Tables v
Acknowledgment vi
1.0 Introduction 1
2.0 EIS/AS Master File . . 4
2.1 Description Record 8
2.1.1 Description Card 1 8
2.1.2 Description Card 2 11
2.1.3 Description Card 3 11
2.1.4 Description Card 4 . 13
2.1.5 Description Card 5 14
2.1.6 Description Card 6 ..... 15
2.1.7 Description Card 7 17
2.2 Category Record . 19
2.2.1 Category Card 1 19
2.2.2 Category Card 2 21
2.2.3 Category Card 3 24
2.2.4 Category Card 4 26
2.2.5 Category Card 5 27
2.3 Comment Record 30
2.3.1 Comment Cards 1 and 2 30
2.4 NEDS A6 Comment Record 32
2.4.1 NEDS A6 Comment Card 32
3.0 EIS/AS Emission Factor File . 33
3.1 Card 1 35
3.2 Card 2 38
3.3 Card 3 39
4.0 EIS/PS Master File 41
4.1 Plant Record 44
4.1.1 Card 1 44
4.1.2 Card 2 47
-------
4.1.3 Card 3 ,48
4.1.4 Card 4 49
4.2 Point Record 50
4.2.1 Card 11 50
4.2.2 Card 12 52
4.2.3 Card 13 58
4.2.4 Card 14 . 62
4.3 SCC Record . . 63
4.3.1 Card 21 63
4.3.2 Card 22 65
4.3.3 Card 23 66
4.3.4 Card 24 68
4.3.5 Card 25 69
4.4 Comment Record 70
4.4.1 Card 30 70
5.0 EIS/PS Emission Factor Files 72
5.1 Card 1. 74
5.2 Card 2 75
5.3 Card 3 76
5'.4 Card 4 .77
Appendix A: EIS/AS Transaction Field. Tables , . . 80
Appendix B: EIS/PS Transaction Field Tables. ..... 96
Appendix C: EIS/AS Input Forms Ill
Appendix D: EIS/PS Input Forms 121
-------
List of Tables
A-l Description - Card 1 81
A-2 Description - Card 2 82
A-3 Description - Card 3 83
A-4 Description - Card 4 85
A-5 Description - Card 5 86
A-6 Description - Card 6 87
A-7 Description - Card 7 88
A-8 Category - Card 1 • 89
A-9 Category - Card 2 90
A-10 Category - Card 3 91
A-ll Category - Card 4 92
A-12 Category - Card 5 93
A-13 Comment Record 94
A-14 NEDS A6 Comment 95
B-l Card 1 - Plant Information 97
B-2 Card 2 - Plant Information 98
B-3 Card 3 - Plant Information 99
B-4 Card 4 - Plant Information 100
B-5 Card 11 - Point Information 101
B-6 Card 12 - Point Information 102
B-7 Card 13 - Point Information 103
B-8 Card 14 - Point Information 104
B-9 Card 21 - SCC Information 105
B-10 Card 22 - SCC Information 106
B-ll Card 23 - SCC Information 107
B-12 Card 24 - SCC Information 108
B-13 Card 25 - SCC Information 109
B-14 Card 30 - Comment 110
-------
ACKNOWLEDGEMENT
This manual was prepared by the Research Triangle Institute, Research
Triangle Park, North Carolina, for the Environmental Protection Agency under
Contract 68-02-3011.
The work has been conducted under the direction of Mr. Edward J. Mask of
the National Air Data Branch (NADB), who is the EPA Project Officer for the
contract.
RTI staff members principally participating in the development of this
document are: '
R. C. Haws, Laboratory Supervisor
L. R. McMaster, Project Leader
D. L. Franke, Analyst/Programmer
W. M. Bailey, Programmer
F. A. Farmer, Programmer
C. 0. Scheper, Programmer
A. F. Tallant, Programmer
D. S. Chase, Secretary
VI
-------
1.0 Introduction
The Emissions Inventory System (EIS) consists of two subsystems:
Emissions Inventory System/Area Source (EIS/AS) and Emissions Inventory
System/Point Source (EIS/PS).
This manual is provided as a supplement to the EIS/AS User's Guide
(EPA-450/4-80-009) and the EIS/PS User's Guide (EPA-450/4-80-010). It
contains detailed information on coding the input transactions for both area
sources and point sources.
An introduction to each subsystem is given detailing the types of records
on the file and information concerning adding records to the file. Then each
card is explained, field by field, giving allowed codes for the field. The
appendices include tables listing each field with its length, characteristic
(alphabetic or numeric),'and which type of transactions the field is allowed
on. Also in the appendices are copies of all input forms.
The EIS coding forms are used to organize emissions data into
computer-readable format for key punching and subsequent entry into
computerized data files. Therefore, all forms must be completed correctly.
In the following discussion, several terms will be used for which the
following definitions are necessary:
FORM - Any of the individual sheets containing coding information, see
Appendices C and D.
CARD - 80-column computer punch card.
COLUMN - One of the vertical columns on the card. The numbers on the
form refer to these columns.
-------
FIELD - a COLUMN or group of" COLUMNS; only one subject to a FIELD. A
FIELD is identified on the FORM by vertical Tines extending above the
COLUMN numbers. The name of the FIELD is printed between the vertical
lines.
LEFT JUSTIFIED - the entry in the FIELD starts at the left side of the
FIELD; it may be alphabetic or numeric; e.g.,
CONTACT PERSON
43
J|Q|H|N|S|0|N|
RIGHT JUSTIFIED - the entry in the FIELD starts at the right side of the
FIELD and is always numeric; e.g.,
EMISSIONS
ESTIMATE
42
3|7|4|9|
ZERO FILLED - zeros are coded in any excess columns when a numeric entry
contains fewer characters than there are columns in the field.
Every entry is either left justified or right justified, unless it is
numeric data containing a decimal point. In that case, an implied decimal
point is indicated by a triangle preprinted on the. form and the data is
entered so that the decimal point in the data corresponds to the triangle on
the form. Zeros are entered in the remaining columns of the field; i.e., the
field is zero filled. The decimal point is not punched on the card. The
following example illustrates coding such data:
EMISSION FACTOR
54
0|0|0|3|7|5Al|0|0|
-------
TEN BASIC FACTS AND RULES FOR COMPLETING CODING FORMS
1. Legibility is mandatory. Print data entries using block capital
letters.
2. Characters - slash zeros (0) and Z's (I)-
3. DON'T change field names.
4. Decimal point - only when a triangle is preprinted in field.
5. To indicate nonapplicable, code a single, right-justified, zero in
the field.
6. NO DATA - leave field blank.
7. Identifiers must be complete! Otherwise, the computer rejects the
entry.
8. Control codes must be complete! Otherwise, the computer rejects the
entry.
9. DON'T use fields (or columns) without names (headings).
10. Left justify letters or alphanumeric fields; right justify numbers.
-------
2.0 EIS/AS Master Tile
The Emissions Inventory System/Area Source (EIS/AS) master file contains
area source emissions data. There are three types of records on the master
file: description, category, and comment.
Description records contain general descriptive information pertaining to
a geographic area. The geographic area may be either a county or a smaller
area denoted by a nonzero geographic suballocation number. The suballocations
can be developed using any method the user desires. Up to 99,999
suballocation numbers per county are allowed.
Category records contain emissions information for a geographic area and
are subordinate to the description record for that area. There can be up to
999 category records for each geographic area: category records 001-064 are
used for the NEDS categories; 065-998 are used for user-defined categories;
and category 999 is generated by CFMMSTR (EC0070). In addition, each category
can be disaggregated with a separate record describing each disaggregation.
Up to 99 disaggregations per category are allowed. The category 999 record
contains a summary of emissions for all the category records with a
disaggregation number of zero.
Comment records are used to include additional information for both
geographic areas (county and/or suballocation description records) and
categories (both category and disaggregation). There can be only one NEDS
comment record for a county description record; all other EIS/AS records can
have up to 999 comment records.
The master file transactions allow the user to add, change, or delete
records on the master file.
•Records can be added to the master file subject to the following
restrictions:
-------
1) A county description record must be present before any other
records will be accepted for that county. The description
record can be added in the same run as the other records.
2) A description record (county or suballocation) must be
present before any category records (or category disaggregation
records) can be accepted for that geographic area.
3) Comment records will only be added if there is a record
in the master file (description or category) with
matching key information, including state, county, geographic
suballocation number, category number, and category
disaggregation number.
4) Any add transaction will create a new record provided that
conditions 1-3 are met.
Each transaction may be divided into three areas named identifiers,
control codes, and data.fields.
The identifiers do just as the name implies - identify category,
geographical location, date, etc.
(IDENTIFIERS FOR EACH CARD (NO BLANKS ALLOWED)
Card No. Columns
Description 1 1 thru 19
Description 2 1 thru 14
Description 3 1 thru 14
Description 4 1 thru 14
Card No. Columns
Description 5 1 thru 14
Description 6 1 thru 14
Description 7 1 thru 19
-------
Card No. Columns
Category 1 1 thru 19
Category 2 1 thru 19
Category 3 1 thru 19
Category 4 . 1 thru 19
Category 5 1 thru 24
Comment 1 1 thru 22
Comment' 2 1 thru 22
NEDS comment 1 thru 9
The control codes tell the computer program what action is required.
Column CONTROL CODES FOR EACH CARD (NO BLANKS ALLOWED)
77 Suballocation type: C - county, S - suballocation
78 G - geographic description (preprinted)
A - category aggregation
D - category disaggregation
R - comment (preprinted)
N - NEDS comment (preprinted)
79 Card Number:
Description 1-7 (preprinted)
Category 1-5 (preprinted)
Comment 1,2
NEDS comment 0 (preprinted)
80 Action code: A - add, C - change, D - delete
All control codes must be filled in for each card that is to be keypunched.
The remainder of the form constitutes the data fields. The discussion
that follows applies to the fields individually or in groups. It will start
with description transactions and continue through category, comment, and NEDS
-------
comment transactions. Note that any data field can be deleted by entering an
asterisk (*) in the left-most column of the field.
See Appendix A for EIS/AS transaction field tables and Appendix C for
EIS/AS input forms.
-------
2.1 DESCRIPTION RECORDT
The description record gi ves infarmation describing.,the- geographic
region.
2.1.1 DESCRIPTION CARD 1
STATE - COLUMNS 1-2
Enter the state identification-code, for-the1.geographic area,. The-
codes can be found, in the_AEROSlM'anua:T Sertes:, Volume; V: AEROS
Manual of Codes, Section 2,. I.Q., The^ entry-must be right, justified.,
zero filled', with no blanks.,
COUNTY - COLUMNS 3-6
Enter-the four-digit code for ther county* or poTitic'al subdivision
(census, division for Alaska,, a.ir pollution: control district for
Massachusetts, or parish for'Louis.iana:).. The-county-identification-
codes are listed in the AEROSlManuaJ Series', Volume V: AEROS Manual
of Codes, Section 2.2.0. The^ entry must; b:e: right: justified., zero
filled, with no blanks.
AQCR - COLUMNS 7-9
Enter the /Virtual ity Control Region'(AQGR) numb.e.r-a.s found in the
AEROS Manual Series, Volume-V: AEROS%Manual of Codes.,. Section
2.3.0. The entry must be right: jus.ttfred:, z:ero filled, w^ith no
blanks-.
SUBALLOCATION NUMBER - COLUMNS 10-14
The suballocation number is used. to:, di'v-i den a,- county into smaller
geographic areas when emissions1 data, arerknown for the smaller
areas. This suballocation is user-dearned1 and is not. required for
EIS/AS. Any technique may be used for-tire suba-1 location.. Enter the
suballocation number if applicable.. Otherwise, leave blank (or fill
with zero). The entry must" be. right justified.
-------
DATE - COLUMNS 15-19
Enter the Julian date of the information recorded in the
transaction. The format is YYDDD, where YY represents the year and
ODD represents the day. The year (first two characters) must not be
greater than the option date year. The day must be between 000 and
366. The entry must be right justified, zero filled, with no
blanks.
AIR BASIN - COLUMNS 20-22
Enter a user-defined code to specify the air basin. The entry must
be right justified.
SMSA - COLUMNS 23-26
Enter the code for the ^Standard Metropolitan Statistical /\rea
(SMSA). See the AEROS Manual Series, Volume V: AEROS Manual of
Codes, Section.2.7.0, for a complete list of SMSA's. The entry must
be right justified.
GEOGRAPHIC NAME - COLUMNS 27-46
Enter a description of the area, either by indicating the county
name or the name of the geographic area.
The entry must left justified.
MAJOR ACTIVITY - COLUMNS 47-66
Enter a description of the major activity of the area. The entry
must be left justified.
ASSOCIATED PLANT ID - COLUMNS 67-70
An associated plant ID may be used to relate emissions from an area
source to a plant (point source) identified in EIS/PS. For example,
in EIS/PS an oil refinery is given a plant ID number and inventoried
as a point source with all emissions assigned to points within the
refinery boundaries. However, the refinery may be the source of
-------
additional fugitive emissions which are actually emitted from many
points all around the refinery area. The fugitive emissions may be
inventoried as an area source and spatially distributed over the
refinery area, but can still be related to the plants and to the
point .source emissions in EIS/PS. The entry must be right
justified.
SIP BASE YEAR - COLUMNS 71-72
Enter the most recent year in which the State Implementation £lan
(SIP) was revised.
PROJECTED YEAR - COLUMNS 73-74
Enter the year for which the projection has been made.
RURAL POPULATION PERCENTAGE - COLUMNS 75-76
Enter the percentage of the area population that is rural. The
entry must be right justified.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation
G CODE - COLUMN 78
The column is preprinted with a G for description record.
CARD NUMBER - COLUMN 79
The column is preprinted with a 1.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
left blank.
10
-------
2.1.2 DESCRIPTION CARD 2
COLUMNS 1-14
These fields are described in detail for the description card 1.
POPULATION - COLUMNS 15-22
Enter the population of the area. The entry must be right
justified.
AQCR NAME - COLUMNS 23-76
Enter a description of the Mr Duality Control Region (AQCR). The
entry must be left justified.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation.
G CODE - COLUMN 78
The column is preprinted with a G for description record.
CARD NUMBER - COLUMN 79
The column is preprinted with a 2.
ACTION CODE - COLUMN 80
Enter A (add), or C (change). D (delete) is not valid for this
transaction. This field must not be left blank.
2.1.3 DESCRIPTION CARD 3
COLUMNS 1-14
These fields are described in detail for the description card 1.
SUBALLOCATION TECHNIQUE - COLUMNS 15-16
A user-defined code to specify the suballocation technique used.
The entry must be right justified.
11
-------
-SUBALLOCATION TECHNIQUE DESCRIPTION - COLUMNS 17-36
Enter a description of the subalLocation -technique used. The .entry
must be left justified.
DEFINED AREA CODE - COLUMNS 37-3.9
Used instead of UTM area descriptors 'When an area Is ;to.o large :or
too complex in shape :to ;be 'described :by coordinates. The co.de
number references .an external \file which-contains digitized boundary
information -for each area. ;An area may be .as large as an /\ir
Duality IMaintenance _Area i'('AQMA;) -or Air Conservation Area (ACA) or as
small as a census tract; e.g..., -it may be .defined .as the eastern half
of a county -or as terrain above a specified altitude. Enter the
user-defined code. The entry must ;be right justified.
SULFUR CONTENTS - COLUMNS 40-47
Enter the percentage of sulfur .contents ('wei;ghted average) for
anthracite coal, bituminous '.coal, -distillate oil,, and residual oil
consumed by area sources in the geographic area. Note that the
triangles indicate decimal points. ;A conditional message will .be
printed if the value exceeds 2..0 for anthracite coal, 7..-Q for
bituminous coal, 1.0 for distillate oil., -.or 5.0 for residual oil.
ASH CONTENTS - COLUMNS 4.8-53
Enter the percentage of ash contents (weighted average) for
anthracite and bituminous coal consumed by area sources in the
geographic area. Note that the triangles indicate decimal points.
A conditional message will be printed if the value exceeds 25.0 for
either subfield.
UTM COORDINATES - COLUMNS 54-75
The geographic area can be described by up to six UTM (JJniversal
T_ransverse Creator Projection System) coordinates. Enter the
zone, horizontal (or easting), and vertical (or northing)
12
-------
coordinates for each desired point of the description. Note that
the triangles indicate decimal points. The valid codes for each
state may be found in the EIS/AS User's Guide, Appendix A, Table
A-l. For further discussion of UTM, refer to the AEROS Manual
Series, Volume II: AEROS User's Manual.
COLUMN 76
This column is not assigned; leave blank.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation.
6 CODE - COLUMN 78
The column is preprinted with a G for description record.
CARD NUMBER - COLUMN 79
The column is preprinted with a 3.
ACTION CODE - COLUMN 80
Enter A (add), or C (change). D (delete) is not valid for
transaction 3. This field must not be left blank.
2.1.4 DESCRIPTION CARD 4
COLUMNS 1-14
These fields are described in detail for the description card 1.
UTM COORDINATES - COLUMNS 15-58
These columns are described in detail for columns 54-75 of
description card 3.
SOURCE TYPE - COLUMN 59
Enter the type of source. Use A for area or L for line or link.
13
-------
, LENGTH OR AREA - COLUMNS v6Q-.66
Enter the length of either ,:a 'tine, or link..source, or theoanea of-an
area source. Note that the :tri:angle Indicates the -decimal point.
LENGTH OF AREA UNITS CODE - COLUMNS-:67-68
Enter any us-er-.defined code to ::sp.ectfy the units'code used for
.length or area.
COLUMNS 69-7.6
These columns are not assigned; leave blank.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballoaction.
G CODE - COLUMN 78
The column is preprinted with a G for description record.
CARD NUMBER - COLUMN 79
The column is preprinted .with a 4.
ACTION NUMBER - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid for
transaction 4. This field must not be left blank.
2.1.5 DESCRIPTION CARD 5
COLUMNS 1-14
These fields are described in detail for the description card 1.
SIP ESTIMATES - COLUMNS 15-37
Enter the State implementation £lan (SIP) emissions estimates for
TSP, S02, NOX, HC, and CO. The estimates are expressed in hundreds
of tons per year. Additional spaces in the record are reserved for
14
-------
future criteria pollutants that might be added. Each entry must be
right justified.
COLUMNS 38-76
These columns are not assigned; leave blank.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation.
G CODE - COLUMN 78
The column is preprinted with a G for description record.
CARD NUMBER - COLUMN 79
The column is preprinted with a 5.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid for
transaction 5. This field must not be left blank.
2.1.6 DESCRIPTION CARD 6
COLUMNS 1-14
These fields are described in detail for the description card 1.
SUBCARD NUMBER - COLUMN 15
This field is generated by CCENETR (EC0030) and is not entered on
EIS/AS master file transactions; leave blank.
POPULATION CODE - COLUMN 16
Enter the EPA population distribution code. The field must be
numeric. See the AEROS Manual Series, Volume V: AEROS Manual
of Codes, Section 3.15, for a complete list of population codes.
15
-------
GAS FUEL FOR LIGHT VEHICLES'- COLUMNS 17-23
Enter the amount of gas fuel: consumed', by' light vehicles- within the;
area. The value is expressed" in: thousands of gal.lonsr.- The-entry
must be right justified.
GAS FUEL FOR HEAVY VEHICLES-. - COLUMNS: 24-29
Enter the amount of gasr fuel consumed by heavy vehicles: within the
area. The value is expressed;, iiir thousands, of gallons. The entry
must be- right justified*
DIESEL FUEL FOR HEAVY VEHICLES - COLUMNS 30-3:5:
Enter the amount of diese-T fuel consumed by heavy vehicles within
the area. The value is. expressed in thousands of gallons. The
entry must be; right justified.
VEHICLE MILES FOR LIMITED ACCESS. ROADS - COLUMNS 36.-41
Enter the number of measured; vehicle; miles: traveled on limited:
access roads in the area. The. value is expressed in tens of
thousands of miles. The.- entry, must be right justified..
VEHICLE MILES TRAVELED FOR RURAL ROADS - COLUMNS 42-47
Enter the number of measured: vehicle miles traveled on rural roads
in the area. The value, is. expressed 1m tens of thousands of miles.
The entry, must, be right justified..-
VEHICLE MILES TRAVELED FOR. SUBURBAN ROADS - COLUMNS' 48-53
Enter the number of measured vehicle miles traveled on suburban
roads in the area. The value is expressed in tens of thousands of
miles. The entry must be right justified.,
VEHICLE. MILES TRAVELED FOR URBAN. ROADS - COLUMNS 54.-60
Enter the number of measured, vehicle.' miles, traveled on urban roads
in the area., The value is expressed; in-tens of thousands of miles.
The entry must be right justified.
-------
COLUMNS 61-76
These columns are not assigned; leave blank.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation.
G CODE - COLUMN 78
The column is preprinted with a G for description record.
CARD NUMBER - COLUMN 79
The column is preprinted with a 6.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid for
transaction 6. This field must not be left blank.
2.1.7 DESCRIPTION CARD 7
COLUMNS 1-14
These fields are discussed in detail for the description card 1.
POLLUTANT ID - COLUMNS 15-19, 43-47
Enter the SAROAD parameter code for the pollutant which is being
identified. Refer to the AEROS Manual Series, Volumn V: AEROS
Manual of Codes for a complete listing of SAROAD parameter codes.
The values used for the criteria pollutants are 11101 (TSP), 42101
(CO), 42401 (S02), 42602 (NOX), 43101 (HC), and 12128 (lead). The
entry must be right justified, zero filled, with no blanks. -
POLLUTANT NAME - COLUMNS 20-34, 48-62
Enter a prose description of the pollutant. The entry must be left
justified.
17
-------
ATTAINMENT STATUS - COLUMN 35, 63
Enter the attainment status of a particular geographic area. The
valid codes are:
A - attainment
N - nonattainment
U - unclassified
If this field is left blank in an add transaction, or if this field
contains an asterisk in a change transaction, U will be assumed and
a warning message will be generated.
AQMA NUMBER - COLUMNS 36-41, 64-69
Enter the air quality maintenance number. The entry must be left
justified.
COLUMNS 42, 70-76
These columns are not assigned; leave blank.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation.
G CODE - COLUMN 78
The column is preprinted with a G for description record.
CARD NUMBER - COLUMN 79
The column is preprinted with a 7.
ACTION CODE - COLUMN 80
Inter A (add), C (change>), or D (delete). This field must not be
left blank.
18
-------
2.2 CATEGORY RECORD
The category record contains identification and emissions data for an
individual category or category disaggregation for a given area.
2.2.1 CATEGORY CARD 1
STATE - COLUMN 1-2
Enter the state identification code for the plant. The codes can be
found in the AEROS Manual Series, Volume V: AEROS Manual of Codes,
Section 2.1.0. The entry must be right justified, zero filled, with
no blanks.
COUNTY - COLUMNS 3-6
Enter the four-digit code for the county (census division for
Alaska, air pollution control district for Massachusetts or parish
for Louisiana). The county identification codes are listed in the
AEROS Manual Series, Volume V: AEROS Manual of Codes, Section
2.2.0. The entry must be right justified, zero filled, with no
blanks.
AQCR - COLUMNS 7-9
Enter the Air Quality Control Region (AQCR) number. The codes can
be found in the AEROS Manual Series, Volume V: AEROS Manual of
Codes, Section 2.3.0. The entry must be right justified, zero
filled, with no blanks.
SUBALLOCATION NUMBER - COLUMNS 10-14
The suballocation number is used to divide a county into smaller
geographic areas when emissions data is known for the smaller
areas. This suballocation is user-defined and is not required for
EIS/AS. Any technique may be used for the suballocation. Enter
the suballocation number. If it is a county transaction, leave
blank (or zero fill). The entry must be right justified.
19
-------
CATEGORY NUMBER - COLUMNS 15-1.7
The category number t? used to describe the activity or process»
Categories 001 through 064 are reserved for NEDS categories,
Categories 065 through 998 are user-defined, and Category 999 is
reserved for emissions totals.. Enter the category number. The
entry must be right justified, zero filled, with n;o. blanks.
CATEGORY DISAGGREGATION NUMBER - COLUMNS 18-19
The category disaggregation number allows the user to refine the
activity associated with the category. Disaggregations are user-
defined. The field should be left blank (or zero filled) for
aggregate category transactions, otherwise the entry must be right
justified, zero filled, with no blanks.
CATEGORY DESCRIPTION - COLUMNS 20-44
Enter a description of the category or disaggregation. The entry
must be left justified.
YEAR OF INFORMATION - COLUMNS 45-46
Enter the year (last two digits) of information for the category
record.
PROCESS RATE - COLUMNS 47-55
Enter the thruput during the inventory year of the fuel or material
used. The process rate is expressed in units defined by the units
code field. The entry must be right justified.
CATEGORY ADJUSTMENT VALUE - COLUMNS 56-62
This field is used when a category is dependent upon two activity
levels, such as burning categories. Enter the second factor
associated with the emission calculation. The entry must be right
justified.
20
-------
UNITS CODE - COLUMNS 63-64
Enter a user-defined code for the thruput (process rate) units. The
entry must be left justified.
UNITS CODE DESCRIPTION - COLUMNS 65-76
Enter a description of the units code. The entry must be left
justified.
. SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation
DISAGGREGATION TYPE - COLUMN 78
Enter A for aggregate or D for disaggregate.
CARD NUMBER - COLUMN 79
The column is preprinted with a 1.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
left blank.
2.2.2 CATEGORY CARD 2
COLUMNS 1-19
These fields are described in detail for the category card 1.
UNIFORM MONTHLY THRUPUTS - COLUMN 20
Enter Y (yes) if monthly thruputs are uniform (monthly thruput
fields should not be coded), or N (no) if monthly thruputs are not
uniform (monthly thruput fields should be coded). If this field is
blank in an add transaction, a value of Y will be assumed.
21
-------
MONTHLY THRUPUT PERCENTAGES - COLUMNS 21-44
For each month, enter the percentage of the total yearly thruput
processed in that month. If the uniform monthly thruput field is Y,
.the monthly thruputs should not be entered (a value of 09 will be
assumed for the thruputs for March, June, September, and December
and a value of 08 will be assumed for the thruputs for all other
months, so that the sum of the thruputs will be 100). If the
uniform monthly thruput field is N, the monthly thruputs should be
provided. Each thruput must be numeric. A leading space is allowed
in each thruput. In an add transaction, a value of zero will be
assumed for any blank thruput. The sum of the thruputs must be
greater than or equal to 95 and less than or equal to 105. The
entries must be right justified.
HOURS PER DAY - COLUMNS 45-46
Enter the number of hours during the day in which the activity
takes place. The entry must be right justified.
DAYS PER WEEK - COLUMN 47
Enter the number of days during the week in which the activity
takes place.
WEEKS PER YEAR - COLUMNS 48-49
Enter the number of weeks during the year in which the activity
takes place. The entry must be right justified.
THRUPUT RATIO - COLUMNS 50-53
The thruput ratio provides an indication of how the operating
schedule of the activity may vary from an average. Many area source
emissions occur infrequently and for brief periods of time; although
the total annual emissions averaged over the year may indicate a
small daily output, emission levels while the activity is operating
are quite high. The ratio of worst day to average daily thruput
22
-------
(process rate for the inventory year divided by 365 days) gives an
indication of what "worst case" emissions could be. Taking forest
fires as an example, the ratio of the maximum acres burned on any
day in which forest fires occurred (or total acres burned in those
fires divided by the number of days that the fires burned) to the
average number of acres burned per day (total acres burned in all
forest fires in the activity area during the inventory year, divided
by 365) is a proper thruput ratio. Note that the triangle on the
coding form indicates an implied decimal point.
MAXIMUM HOURLY THRUPUT - COLUMNS 54-63
Enter the maximum hourly thruput of the fuel or material used. The
maximum hourly thruput is expressed in units defined by the units
code field. Note that the triangle on the coding form indicates an
implied decimal point.
DATA CONFIDENCE RATING - COLUMN 64
Enter a user-defined code to indicate a confidence rating for the
data. This field is used to obtain a confidence rating for the
emissions estimate. The field must be numeric. If the field is
blank in an add transaction, or an asterisk in a change transaction,
a value of zero will be assumed for the field.
NITROGEN CONTENT - COLUMNS 65-67
Enter the nitrogen content for combustion processes. The nitrogen
content is indicated as a weight percentage. Note that the triangle
on the coding form indicates an implied decimal point.
SULFUR CONTENT - COLUMNS 68-69
Enter the sulfur content for combustion processes. The sulfur
content is indicated as a weight percentage. Note that the triangle
on the coding form indicates an implied decimal point.
23
-------
ASH CONTENT - COLUMNS 70-72
Enter the ash content for combustion processes. The ash. content Is
expressed as a weight percentage. Note that the triangle on the
coding form indicates an implied decimal point.
HEAT CONTENT - COLUMNS 73-76
Enter the heat content for combustion processes. Units are millions
of BTU per category.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation.
DISAGGREGATION TYPE - COLUMN 78
Enter A for aggregate or D for disaggregate.
CARD NUMBER - COLUMN 79
The column is preprinted with a 2.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid for
transaction 2. This field must not be 'left .blank.
2.2.3 CATEGORY CARD 3
COLUMNS 1-19
These fields are discussed in detail for the category card 1.
UNIFORM HOURLY THRUPUTS - COLUMN 20
Enter Y (yes) if hourly thruputs are uniform (hourly thruput fields
should not be coded), or N (no) if hourly thruputs are not uniform
(hourly thruput fields should be coded). If this field is blank in
an add transaction, a value of Y "will be assumed.
24
-------
HOURLY THRUPUT PERCENTAGES - COLUMNS 21-68
For each hour, enter the percentage of the total daily thruput
processed in that hour. If the uniform hourly thruput field is Y
(yes), the hourly thruputs should not be entered (a value of 05 will
be assumed for the thruputs for hours 0500, 1100, 1700, and 2300 and
a value of 04 will be assumed for the thruputs for all other hours,
so that the sum of the thruputs will be 100). If the uniform hourly
thruput field is N (no), the hourly thruputs should be provided.
Each thruput must be numeric. A leading space is allowed in each
thruput. In an add transaction, a value of zero will be assumed for
any blank thruput. The sum of the thruputs must be greater than or
equal to 95 and less than or equal to 105. The entries must be
right justified.
COLUMNS 69-76
These columns are not assigned; leave blank.
SUBALLOCATION TYPE - COLUMN 77
Enter C for county or S for suballocation
DISAGGREGATION TYPE - COLUMN 78
Enter A for aggregate or D for disaggregate.
CARD NUMBER - COLUMN 79
The column is preprinted with a 3.
ACTION CODE - COLUMN 80
Enter A (add), or C (change). D (delete) is not valid for
transaction 3. This field must not be left blank.
25
-------
.2.2/4 CATEGORY CARD-4
COLUMNS 1-19
These fields are discussed in:detail 'for .the category card .1.
NEDS A7 COMMENT - COLUMNS .20-33
.Enter the information 'to 'be ^transmitted :on:.a NEDS 1A7 card. The
entry must be left justified.
INFORMATION SOURCE .CODE - COLUMN 5.4
Enter a user-defined.code to specify "the type of-source from which
;the rate information was .-received.
INFORMATION SOURCE NARRATIVE -.COLUMNS 55-74
Enter the name-or a description .of 'the information source. The
entry must-be left justified.
COLUMNS 75-76
These columns are not as-signed; leave.blank.
SUBALLOCATION TYPE - COLUMN 77
Enter C forxounty or S for suballocation.
DISAGGREGATION CODE - COLUMN 78
:Enter A for-^aggregate, D for .disaggregate.
CARD NUMBER - COLUMN 79
The column Is preprinted -with ~a '4.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is'not valid for
transaction 4. This field must not.be"left blank.
.26
-------
2.2.5 CATEGORY CARD 5
COLUMNS 1-19
These fields are discussed in detail for the category card 1.
POLLUTANT ID - COLUMNS 20-24
Enter the SAROAD parameter code for the pollutant whose emissions
are being measured. Refer to the AEROS Manual Series, Volume V:
AEROS Manual of Codes for a complete listing of SAROAD parameter
codes. The entry must be right justified, zero filled, with no
blanks. The pollutant ID's for the criteria pollutants are 11101
(TSP), 42101 (CO), 42401 (S02), 42602 (NOX), 43101 (HC), and 12128
(lead).
EMISSION FACTOR - COLUMNS 25-34
Enter statistical average of the rate at which a pollutant is
released into the atmosphere as a result of some activity. The
Federal emission factors for each category can be found in
Compilation of Air Pollutant Emission Factors, EPA Publication No.
AP-42. Note that the triangle on the coding form indicates an
implied decimal point.
EMISSION FACTOR CONFIDENCE RATING - COLUMN 35
Enter a user-defined code to specify confidence in emission factor
information. This field is used in a calculation of emission
confidence rating. The field must be numeric. If the field is
blank in an add transaction or an asterisk in a change transaction,
a value of zero will be assumed.
EMISSION FACTOR ORIGIN - COLUMN 36
Enter the origin of the emission factor information. The valid
codes are:
F - Federal
L - Local
S - State
27
-------
EMISSION FACTOR SOURCE - COLUMN '3.7
Enter a user-defined code bo further specify t'kve (origin ;of local
emission factor information.. Leave ib'Tank for ;state- or'Red-era;! -
origin emission factor .information..
POLLUTANT SPECIFIC .DATA - COLUMNS 38-4.7
• Enter user-defined suRpliementary in.formaition 'keyed to the pollutant
ID code. For instance., this field may contain .particulate size
range information for total susp.endied ;particulate emissions (e.g.,
it may show the percent of total emitted ^articulates with average
diameter less than 2 microns, less than 7, and less than 10), In
the case of organic gas emissions, this field may contain a code
number referencing an emission profile file.
NEDS A7 EMISSION - COLUMNS 48-54
Enter the emissions estimate value to be used on a NEDS A7 card (for
criteria pollutants). The entry must ;be right justified.
POLLUTANT NAME - COLUMNS .55-69
Enter a prose description of the pollutant. Refer to the AEROS
Manual Series, Volume V: AEROS Manual of Codes for a complete list
of pollutant names. The field must be left justified.
COLUMNS 70-76
These columns are not assigned; leave blank.
SUBALLOCATION TY.PE - COLUMN 77
Enter C for county or S for suballocation.
DISAGGREGATION TYPE - COLUMN 78
Enter A for aggregate, D for disaggregate.
28
-------
CARD NUMBER - COLUMN 79
The column is preprinted with a 5.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
left blank.
29
-------
2'.3: COMMENT RECORD
The comment record is used to record! addition-al! infoirmatfam for a
geographic area or a process,. Comment records; may/ be subordinate to
description records (both county and suballocation) and category records (both
aggregate and disaggregate).
2.3.1 COMMENT CARDS 1 AND 2
COLUMNS 1-19
These fields are discussed in detail for the category card 1. On a
comment record, the subal location number, category number, and
disaggregate numbers should only be used i:f the related record is
a suballocation, category, or disaggregate, respectively.
LINE NUMBER - COLUMNS 20-21
Enter a user-assigned sequential number for a comment. The field
must be numeric. The line number must be nonzero for an add or
change transaction. A zero or blank line number is allowed for
delete transactions and causes all lines of an E.IS/AS comment to be
deleted. Leading spaces are allowed.
HALF COMMENT - COLUMNS 23-72
Enter the left half of an EIS/AS comment on a card number 1 and a
right half on a card number 2. The entry must be left justified.
COLUMNS 73-77
These columns are not assigned; leave blank.
R CODE - COLUMN 78
The column is preprinted with an R for comment record.
CARD NUMBER - COLUMN 79 -
Enter 1 for the left half comment and 2 for the right half comment.
30
-------
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be left
blank.
31
-------
2.4 NEDS A6 COMMENT RECORD
The NEDS A6 comment record is subordinate, to a county description record.
It contains a comment to be transmitted on a NEDS A6 card.,
2.4.1 NEDS A6 COMMENT CARD
COLUMNS 1-9 (State, County, AQCR)
These fields are discussed in detail for the description card 1.
NEDS A6 COMMENT - COLUMNS 10-77
Enter a comment to be transmitted on a NEDS A6 card. This field
should not be blank. If this field is blank, in an add transaction,
or if the first character of this field ts- an asterisk in a change
transaction, a value of 'GENERATED BY EIS/AS' will be assumed.
N CODE - COLUMN 78
The columir is preprinted with an N for NEDS 16 Comment record.
CARD NUMBER - COLUMN 79
The column is preprinted with a- 0.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
left blank.
32
-------
3.0 EIS/AS Emission Factor File
The EIS/AS emission factor file is used to insert emission factor
information into the master file transactions and to generate master file
transactions when updates to the emission factor file consists of two types of
records: category records and pollutant records. Pollutant records are
subordinate to category records and, therefore, cannot exist in the emission
factor file without corresponding category records.
A category record can be added to the emission factor file by processing
a category-1 (type 1) add transaction or by processing both category-1 and a
category-2 (type 2) add transaction for the desired category. Note that a
category-2 add transaction is not valid unless it is preceded by a category-1
add transaction with the same key information.
An existing category record can be changed by processing a category-1
change transaction and/or a category-2 change transaction.
An existing category record can be deleted from the emission factor
file by processing a category-1 delete transaction. A category-2 delete
transaction is not valid; all of the fields in the category record are deleted
by the category-1 delete transaction. Also, a category-1 delete transaction
deletes all of the pollutant records associated with the category record.
A pollutant record can be added to the emission factor file by processing
a pollutant (type 3) add transaction; however, the corresponding category
record must exist in the emission factor file. If the category record is not
in the file, it must be added prior to adding the pollutant record. This can
be accomplished in the same run because the emission factor file transaction
sort program, CSREFTR (EC0010), sorts the transactions so that pollutant
transactions follow their associated category transactions.
33
-------
An existing pollutant record can be changed by processing a pollutant
change transaction.
Also, an existing pollutant record can be deleted from the emission
factor file by processing a pollutant delete transaction. Each pollutant
delete transaction deletes a single pollutant record from the emission factor
file.
34
-------
3.1 EMISSION FACTOR CARD 1
STATE - COLUMNS 1-2
Enter the state identification code associated with the emission
factor. The codes can be found in the AEROS Manual Series, Volume
V: AEROS Manual of Codes, Section 2.1.0. The entry must be right
justified, zero filled, with no blanks.
COUNTY - COLUMNS 3-6
Enter the four-digit code for the county or political subdivision
(census division for Alaska, air pollution control district for
Massachusetts, or parish for Louisiana). The county identification
codes are listed in the AEROS Manual Series, Volume V: AEROS Manual
of Codes, Section 2.2.0. The entry must be right justified, zero
filled, with no blanks.
SUBALLOCATION NUMBER - COLUMNS 7-11
The suballocation number is used to divide a county into smaller
geographic areas when emission data is known for the smaller areas.
This suballocation is user-defined and is not required for EIS/AS.
Any technique may be used for the suballocation. Enter the
suballocation number associated with the emission factor. If it is
a county transaction, leave blank (or zero filled). The entry must
be right justified.
/
CATEGORY NUMBER - COLUMNS 12-14
The category number is used to describe the activity or process.
Categories 001 through 064 are reserved for NEDS. Categories 065
through 998 are user-defined, and Category 999 is reserved for
totals. Enter the category number associated with the emission
factor. The entry must be right justified, zero filled, with no
blanks.
35
-------
CATEGORY DISAGGREGATION NUMBER - COLUMNS 15-16
The category disaggregation number allows the user to refine the
activity associated with the category. Disaggregations are user-
defined. The field should be left blank (or zero filled) for
aggregate category transactions; otherwise, the entry must be right
justified, zero filled, with no blanks.
COLUMNS 17-23
These columns are not assigned; leave blank.
DATE - COLUMNS 24-28
Enter the Julian date of the transaction in the form YYDDD. The
entry must be right justified, zero filled, with no blanks.
NITROGEN FLAG - COLUMN 29
Enter code to indicate whether or not a nitrogen content is to be
used in the calculation of an estimated emission. The valid codes
are:
N - Nitrogen content used.
Blank -Nitrogen content not used.
SULFUR FLAG - COLUMN 30
Enter code to indicate whether or not a sulfur content is to be used
in the calculation of an estimated emission. The valid codes are:
S - Sulfur content used.
Blank - Sulfur content not used.
ASH FLAG - COLUMN 31
Enter code to indicate whether or not an ash content is to be used
in the calculation of an estimated emission. The valid codes are:
A - Ash content used.
Blank - Ash content not used.
36
-------
NITROGEN CONTENT - COLUMNS 32-34
Enter the weight percentage amount of nitrogen for a combustion
process. Note that the triangle on the coding form indicates an
implied decimal point.
SULFUR CONTENT - COLUMNS 35-37
Enter the weight percentage amount of sulfur for a combustion
process. Note that the triangle on the coding form indicates an
implied decimal point.
ASH CONTENT - COLUMNS 38-40
Enter the weight percentage amount of ash for a combustion process.
Note that the triangle on the coding form indicates an implied
decimal point.
CATEGORY DESCRIPTION - COLUMNS 41-65
Enter a brief description of the category (or disaggregation). The
entry must be left justified.
COLUMNS 66-78
These columns are not assigned; leave blank.
CARD NUMBER - COLUMN 79
The column is preprinted with a 1.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
left blank.
37
-------
3:.,2 EMISSION FACTOR CARD 2
COLUMNS 1-28
These fields are described fn detail? for card 1..
COUNTY NAME - COLUMNS 29-48,
Enter the name of the county. The entry must be: left justified.
COLUMNS 49-78
These columns are not assigned;, leave blank.
CARD NUMNBER - COLUMN 79
The column is preprinted with a 2.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete), is. not valid for card 2.
This field: must not be left blank.
-------
3.3 EMISSION FACTOR CARD 3
COLUMNS 1-16
These fields are described in detail for card 1.
ORIGIN - COLUMN 17
Enter the origin of the emission factor information. The valid
codes are:
F - Federal
S - State
L - Local.
SOURCE - COLUMN 18
Enter a user-defined code to identify individual local emission
factors. This code is used in conjunction with the emission factor
origin to differentiate between local emission factors.
POLLUTANT ID - COLUMNS 19-23
Enter the SAROAD parameter code for the specific pollutant whose
emission factor information is being recorded. The six codes
recognized by EIS/AS for the criteria pollutants and lead are:
11101 - total suspended particulates; 12128 - lead; 42401 - carbon
monoxide; 42401 - sulfur dioxide; 42602 - nitrogen dioxide; and
43101 - total hydrocarbons. Refer to the AEROS Manual Series,
Volume V: AEROS Manual of Codes, for a complete listing of SAROAD
parameter codes.
DATE - COLUMNS 24-28
Enter the Julian date of the transaction in the form YYDDD. The
entry must be right justified, zero filled, with no blanks.
EMISSION FACTOR - COLUMNS 29-38
Enter a statistical average of the rate at which a pollutant is
released into the atmosphere as a result of the activity. Note that
39
-------
the triangl,e on i'he (ood^rng f-oum indicates an implied decimal ip-omnt.
Refer to the AEROS 'Manual 'Series,, 'Vo'lhume W-: AERGS Mantrai] 'of -Cotes
for further information.
CONFIDENCE LEVEL - COLUMN 39
Enter a user-defined -value showing the ,reliability :of t'h:e
.emission factor. The field -must 'be numeric.
POLLUTANT "NAME - COLUMNS 40-54
Enter the name of the pollutant. The entry must f>e left justified.
POLLUTANT SPECIFIC DATA - COLUMNS 55-64
Enter any pollutant-related information:. The field is inserted into
the master file and may be printed on reports.
COLUMNS '65-78
These columns are not assigned; leave ;b!ank.
CARD NUMBER - COLUMN 79
The column is preprinted witti a 3.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D {delete). This field must not be
left blank.
40
-------
4.0 EIS/PS Master File
The Emissions Inventory System/Point Source (EIS/PS) master file contains
point source emission data.
The EIS/PS master file contains four types of records: plant, point,
SCC, and comment. The plant record contains general descriptive information
pertaining to an individual plant (point source). Plants are defined by a
plant ID within the county. These ID's are assigned sequentially beginning
with 0001.
Each plant can contain up to 1,296 emission points. Each emission point
is defined by a point record. Refer to AEROS Manual Series, Volume II: AEROS
User's Manual, Section 3.1.2, for a discussion of the grouping of emission
points. NEDS point ID's are used to identify the points. The point record
contains descriptive information on the point and its emissions, as well as
detailed emission information for a maximum of 16 pollutants.
Each point record can have up to ten SCC records associated with it.
More than one SCC record can be defined for an SCC by using the SCC sequence
number. The SCC record contains descriptive information related to the SCC as
well as detailed emission factor information for a maximum of 16 pollutants.
Comment records are related to emission points. Up to 99 comments with
up to 999 lines (records) each can be used for a single point record. The
comment records are 'free form text1 and can contain permits and registration
information as well as other comments desired for the point. No information
from the comment records is transmitted to NEDS.
The master file transactions allow the user to add, change, or delete
records on the master file.
Records can be added to the master file subject to the following
restrictions:
41
-------
Plant - Valid 01, 02, and 03 transactions are required to add a
plant record.
Point - A plant record must be present in the master file before any
point will be accepted for that plant. Valid 11 and 12
transactions, and at least one valid 13 transaction, are
required to add a point record.
SCC - A point record must be present in the master file before
any SCC's will be accepted for that point. Valid 21 and
22 transactions and at least one valid 23 transaction are
required to add an SCC record.
Comment - A point record must be present in the master file before
any comments will be accepted for that point. A valid 30
transaction is required to add a comment. Any numeric
line number can be used.
Each transaction may be divided into three areas named identifiers,
control codes, and data fields.
The identifiers, as the name implies, identify plant name, geographic
location, date, etc.
IDENTIFIERS FOR EACH CARD (NO BLANKS ALLOWED)
Card No. Columns
1 1-18, 36-41
2 1-18
3 1-18
4 1-18
11 1-20
12 1-20
42
-------
Card No. Columns
13 1-25
14 1-20
21 1-30
22 1-30
23 1-37
24 1-30
25 1-30
30 1-26
The one exception to NO BLANKS in the IDENTIFIER field concerns the City Code
on Card One, Columns 36-39. « This exception is discussed later in this
section.
The control codes cause the computer program to take the action
required.
Column CONTROL CODES FOR EACH CARD (NO BLANKS ALLOWED)
78-79 Card Number This code is preprinted on the coding •
form.
80 Action Code A - add, C - change, D - delete.
All control codes must be filled in for each card that is to be keypunched.
The rest of the form constitutes the data fields. The discussion that
follows applies to the fields individually, or in groups. The discusssion
will start with the point record transactions (cards 1 through 4) and continue
through the comment record transactions (card 30). Note that any data field
can be deleted by entering an asterisk (*) in the left-most column of the
field.
See Appendix B for EIS/PS field tables and Appendix D for EIS/PS input
forms.
43
-------
4.1 PLANT RECORD
The plant record contains information to identify and locate a facility
that has been determined to be a point source-
4.1.1 PLANT RECORD CARD 01
STATE - COLUMNS 1-2
Enter the state identification code for the plant. The codes can be
found in the AEROS Manual Series, Volume V: AEROS Manual of Codes,
Section 2.1.0. The entry must be right justified, zero filled,
with no blanks.
«
COUNTY - COLUMNS 3-6
Enter the four-digit code for the county (census division for
Alaska, air pollution control district for Massachusetts, or parish
for Louisiana). The county identification codes are listed in the
AEROS Manual Series, Volume V: AEROS Manual of Codes, Section
2.2.0. The entry must be right justified, zero filled, with no
blanks.
AQCR - COLUMNS 7-9
Enter the Mr Duality Control Region (AQCR) number as found in
the AEROS Manual Series, Volume V: AEROS Manual of Codes, Section
2.3.0. The entry must be right justified, zero filled, with no
blanks.
PLANT ID NUMBER - COLUMNS 10-13
Enter the plant ID number as assigned within the county. Plant ID
numbers must be unique for each plant within a county. The state,
county, and AQCR codes will differentiate all the plants with the
same plant ID number. The regional office is responsible for
assigning plant ID numbers, but that responsibility may be
delegated. Once assigned, a plant ID should not be changed. In
44
-------
most cases, the simplest and most meaningful method for assigning
plant ID numbers is to begin with 0001 and number the plants
sequentially up to the number of plants in the county. However,
some agencies prefer to assign other special code numbers, and this
is acceptable. Use of alphabetic codes or an alphanumeric
combination for a plant ID number is also acceptable; however, care
should be taken to ensure that, for reports, any desired sort order
for the plants within a county will not be disrupted by the
assignment of alphanumeric ID's. The sequence for sorting is that
alphabetic ID's follow numeric ID's. However, alphanumeric ID's may
fall between numeric ID's. As examples, an ID of OOOA would follow
0009 and precede 0010 in the sort order, A001 would follow 9999 and
precede B001, etc. In all cases, no blanks are allowed in the plant
ID number field. Entries must be zero filled as necessary.
DATE OF RECORD - COLUMNS 14-18
Enter the Julian date of the information recorded in the
transaction. The format is YYDDD, where YY represents the year and
ODD represents the day. The year (first two characters) must not be
greater than the option date year. The day must be between 000 and
366. The entry must be right justified, zero filled, with no
blanks.
CONTROL REGION - COLUMNS 19-21
Enter any user-defined code used to identify the state or local
control area. The entry must be left justified.
LOCAL CONTROL - COLUMNS 22-23
This field allows the user to identify plants that are physically
located in one control region, but whose control is under the
jurisdiction of another control region. The entry must be left
justified.
45
-------
USER PLANT ID - COLUMNS 24-35
Enter any user-defined plant source identification which may differ
from the NEDS conventions. The entry must be left justified.
CITY - COLUMNS 36-39
Enter the SAROAD code number corresponding to the city in which the
source is located. Refer to the AEROS Manual Series, Volume V:
AEROS Manual of Codes, Section 2.2.0, for a full list of city codes.
If the city is not listed, or the plant is not in a city, leave the
field blank. Otherwise, the entry must be right justified, zero
filled, with no blanks.
UTM ZONE - COLUMNS 40-41
Enter the zone associated with the UTM (Universal Jransverse
]1ercator Projection System) coordinates given for the source. UTM
coordinates can be obtained from USGS -maps. The valid codes may be
found in the EIS/PS User's Guide, Appendix A, Table A-l. For
further discussion, refer to the AEROS Manual Series, Volume II:
AEROS User's Manual. The entry must be right justified, zero
filled, with no blanks.
OWNERSHIP CODE - COLUMN 42
Enter the NEDS code used to designate the type of ownership. Values
are:
P - Private
L - Local government
S - State government
F - Federal government
U - Utility
This field must not be left blank.
46
-------
CONTACT PERSON - COLUMNS 43-57
Enter the last name of the person responsible for the pollution
control activity at the source. If an individual is not identified,
a position title should be given. The entry must be left justified.
TELEPHONE - COLUMNS 58-67
Enter the telephone number (including area code) of the person
listed in the contact field. The entry must be right justified,
zero filled, with no blanks.
PRINCIPAL PRODUCT - COLUMNS 68-77
Enter the principal product produced by the plant. The entry must
be left justified.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 01.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
blank.
4.1.2 PLANT RECORD CARD 02
COLUMNS 1-18
These fields are described in detail for the plant record card 01.
ESTABLISHMENT NAME AND ADDRESS - COLUMNS 19-66
Enter a descriptive name for the plant and a usable mailing address.
This is the name and address that is transmitted to NEDS. The
entry must be left justified.
47
-------
NUMBER OF EMPLOYEES - COLUMNS' 67-70
Enter the number of persons who work at the plant. The-entry must
be right justified.
PROPERTY AREA - COLUMNS 71-76
Enter the area, to the nearest tenth of an acre, of the land
occupied by the facility. Note'that the-triangle on the coding form
indicates an implied decimal point.
COLUMN 77
This column is not assigned; leave bTank.
CARD NUMBER - COLUMNS 78-79.
The columns are preprinted-w-fth the? card number 02:.:
ACTION CODE - COLUMN 80
Enter A (add), or C (change.). D (delete1) is not valid: on a card 02.
This field must not. be blank-.,
4.1.3 PLANT RECORD CARD 03
COLUMNS 1-18
These fields are described vn detail for pTant record, card 01.
ESTABLISHMENT MAILING ADDRESS' - COLUMNS 19-66
Enter the address to contact if it is different, than the
establishment name and address. The entry- must be left justified.
COLUMNS 67-77
These columns are not assigned';, leave blank.
CARD NUMBER - COLUMNS 78-79
The columns, are preprinted, with the card, number 03.
48'
-------
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid on a card 03.
This field must not be blank.
4.1.4 PLANT RECORD CARD 04
COLUMNS 1-18
These fields are described in detail for plant record card 01.
NEDS P7 PLANT COMMENT - COLUMNS 19-70
Enter information to be transmitted on a NEDS P7 card. The entry
must be left justified.
COLUMNS 71-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
These columns are preprinted with the card number 04.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid on a card 04.
This field must not be blank.
49
-------
4.2 Point Record
The point record contains emission and identifying informat.io.n: for an
individual point within a plant.
4.2.1 POINT RECORD CARD 11
COLUMNS 1-18
These fields are described in detail for point record card 01.
NEDS POINT ID - COLUMNS 19-20
The NEDS point ID is a sequential number used to designate an
emission point within a plant. There cannot be any blanks in the
field; either numbers or letters may be. used. Numbers will sort
first, beginning with 00. For further discussion on assigning point
ID'S, see the AEROS Manual Series, Volume II: AEROS User's Manual,
Section 3.1.2.
USER POINT ID - COLUMNS 21-23
Enter any local plant identification which differs from the NEDS
conventions. The entry must be left justified.
SIC - COLUMNS 24-27
Enter the Standard Industrial' Classification code associated with
the point. SIC codes can be found in the Standard Industrial
Classifications Manual, 1973.. The entry must be left justified.
IPP - COLUMNS 28-29
Enter the ^Implementation Planning.program process (IPP) code. Refer
to the AEROS Manual Series, Volume V: AEROS Manual of Codes,
Section 3.2.0, for a full list of IPP codes. The entry must be
right justified.
50
-------
UTM HORIZONTAL - COLUMNS 30-33
Enter the horizontal (or easting) coordinate for the UTM (Universal
Transverse Mercator Projection System) measurement of the source.
UTM coordinates can be obtained from USGS maps. For further
discussion see the AEROS Manual Series, Volume II: AEROS User's
Manual and the EIS/PS User's Guide, Appendix A, Table A-l.
UTM VERTICAL - COLUMNS 34-38
Enter the vertical (or northing) coordinate for the UTM measurement
of the source. UTM coordinates can be obtained from USGS maps. For
further discussion see the AEROS Manual Series, Volume II: AEROS
User's Manual and the EIS/PS User's Guide, Appendix A, Table A-l.
LATITUDE - COLUMNS 39-44
Enter the latitude of the point source. Coordinates can be obtained
from a USGS map. The field must be zero filled.
LONGITUDE - COLUMNS 45-51
Enter the longitude of the point source. Coordinates can be
obtained from a USGS map. The field must be zero filled.
ANNUAL THRUPUT - COLUMNS 52-59
The field is divided into four three-month periods representing one
year. Each subfield contains the weighted percentage of the yearly
activity for that period. If all activity occurs in one period,
enter 99 for that period and zeros for the other periods. The field
must be numeric. The four quarterly percentages should add up to
95-105%.
OPERATING RATE - COLUMNS 60-64
The first two digits indicate the hours per day of normal operation;
the third digit, the days per week; and the last two, the weeks per
year. Each subfield must be right justified.
51
-------
BOILER CAPACITY - COLUMNS -65*69
Enter the boiler input capacity b.efore heat-.transfer. .Units ;a re "in
millions of BTU per hour. .Zero should .be.used :for.points:not
containing a boiler. Notetthat .a-boiler Is defined .-as-a ^burner,
firebox, or heat exchanger, .and a means .of creating .and directing
a flow of gases through the .unit. The .entry must-be right
justified.
SPACE HEAT - COLUMNS 70-72
Enter the percentage of total -fuel used for :space'heating the plant.
If no fuel is used for--space h.eating, enter zeros. Note that the
triangle on the coding form indicates an implied-decimal .point.
COLUMNS 73-77
Thes.e columns are not assigned; Leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 11.
ACTION CODE - COLUMN 80
Enter A (add), C (change) or D (-delete). This -field must not be
blank.
4.2.2 POINT RECORD CARD 12
COLUMNS 1-20
These fields are described in detail for plant record card 01 and
point record card 11.
STACK DATA - COLUMNS 21-47
Before entering data in this field, which has six subfields, there
are some considerations -that affect .the ent-ire field. When several
similar boilers that emit pollutants through separate stacks have
.been combined, the following procedure wiTl .be used to determine the
-52
-------
actual stack parameters to be recorded. Calculate K-j for each
individual stack using the following equation:
KJ = OH )(Vi)(Ts1 )/(},•
where: H-j = individual stack height, ft
V-j = individual gas flow rate, ft-^/min
Tsj = individual stack temperature, °F
Q-J = individual emission rate of any common pollutant, T/yr
Select the stack with the lowest Ki value, and enter this stack
height, diameter, temperature, and flow rate on the coding form in
the appropriate fields. Enter in the "Comments" section, Card Six,
the total number of boilers and the total number of stacks
combined.
If there are entries in the height, diameter, and flow rate fields,
then the plume height field should contain a single, right justified
zero to indicate nonapplicability. Conversely, if the height,
diameter, and flow rate fields contain zeros, then there must be an
entry in the plume height field.
There are point sources that have one or more of the following
characteristics:
1. No clear-cut or enclosed point of emission.
2. No stack height (e.g., burning dumps).
3. A changing locus of emissions within the facility (e.g.,
leaking valves at an oil refinery, dust from moving
equipment in a quarry).
In such cases, the stack height, temperature, and flow rate columns
on the coding form should be marked with zeros and columns 44
through 47 completed.
The STACK HEIGHT, columns 21-24, is the vertical distance between
the point of emission and ground level. If an estimate of stack
height must be made, that value should be rounded to the nearest 10
53
-------
f°pt. In the majority of cases, the exact location of the discharge
of pollutants will be well defined,; there wiTl be a .stack or some
other enclosed, constrained, or .physically bounded area where
pollutants are emitted. The .entry must be in feet, right justified,
blanks allowed.
The STACK DIAMETER, columns 25-27, is the inside diameter of a round
gas exit at the point of emission; for nonround exits, it is an
equival'ent diameter calculated from the cross-sectional area at the
point of discharge. Using a measured or estimated cross-sectional
area, the equivalent diameter (De) is calculated as follows:
De = 1.128 A
where A is in square feet. For another common occurrence -the
rectangular stack exit -the equivalent stack diameter must be
calculated from the total cross-sectional area; it cannot be assumed
to be one of the linear dimensions. The entry must be in feet and
tenths of feet (note that the triangle on the coding form indicates
the implied decimal point), right justified, blanks all-owed.
The STACK TEMPERATURE, columns 28-31, of the exhaust stream at the
stack exit is reported in degrees Fahrenheit under normal operating
conditions. If measured temperatures are not available, an estimate
to the nearest 50°F should be made. If no fuel combustion is
involved in the process, and if the exhaust gas appears to be
discharged at ambient air temperatures, then record the stack gas
temperature as 77°F unless a definite value is known. If a plume
height is entered for a source., enter 77°F for cases without
combustion, and estimate the temperature for cases with combustion.
The entry must be in degrees Fahrenheit., right justified, blanks
allowed.
54
-------
The FLOW RATE, columns 32-38, is the actual exhaust-gas volume of
exhaust gas released at the operating temperature of the stack
(assume gas pressure is the same as normal atmospheric pressure).
When two or more boilers discharge into a common stack and each
boiler is coded on a separate form, the exit-gas flow rate
corresponding to each boiler is entered on the coding form. The
flow rate should be reported using the following order of priority
for selection:
1. Actual or measured under normal conditions.
2. Design rate.
•
3. Maximum rate.
The entry must be in cubic feet per minute (ft^/min), right
justified, blanks allowed.
The VELOCITY, columns 39-43, is the exhaust-gas velocity for the
point. If the actual measurement is not available, use the design
or maximum value. The entry must be in feet per minute, right-
justified, blanks allowed.
The PLUME HEIGHT, columns 44-47, is to be filled in if the previous
spaces on stack data (except temperature) all contain zeros.
Conversely, jjf stack height, diameter, temperature, and flow rate
were reported, then column 47 should contain a zero. The plume
height is a gross estimate and is used only when the source has one
of the following characteristics:
1. No clear-cut enclosed point of emission (e.g., gas leaks
at an oil refinery).
2. No stack height (e.g., burning dumps).
3. A mobile emission point within the facility (e.g.,
quarry).
4. Pollutants released into the atmosphere at ambient
temperatures through diffusion (e.g., gasoline storage
tanks).
55
-------
Many point sources have no true stack release points (whereby the
gases are forcibly exhausted to the atmosphere from an enclosed
area). In such cases, columns 44 through 47 must be completed. If
there is a physically definable height above ground level where the
pollutants are discharged, then enter this value (in feet) in the
spaces. Examples of this class are gasoline storage tanks and
uncontrolled grain-drying operations where the height of the tank or
dryer would be considered the plume height. On the other hand,
some sources, such as some quarries, burning dumps, and gas leaks at
ground level at an oil refinery, have no discernible emission
height. In such cases, enter zero in column 47. Processes that-
discharge emissions at ambient temperatures mainly through
ground-level leakage or diffusion should also be considered to have
a zero plume height. In such cases the exhaust flow rate entered
in columns 32 through 38 will also be zero. Ground-level emissions
which are coded as zero plume heights should have an appropriate
temperature entered in columns 28 through 31. Conical refuse
burners must have stack data entered on the coding form. The entry
must be in feet, right justified, no blanks allowed.
POINTS WITH COMMON STACK - COLUMNS 48-51
Entries will be made if emission points discharge through a common
stack. Enter four zeros if there is one emission point and one
stack. First and most important is that the units in this
combination MUST be numbered consecutively. Second, a form for
each unit in the combination MUST be completed. For example, if
plant X has 15 emission points, three of which discharge through a
common stack, 15 point source input forms would be completed. On
three of these forms, enter indentical stack data for the stack
common to the three emission points, except that stack flow rate
will be different on each of these three forms. On each of these
three forms, also enter the lowest and highest of the emission point
ID numbers assigned to the emission points with a common stack.
56
-------
Let's say that of the 15 emission points in this plant, the four for
emission point 04, will have a 04 in columns 19-20 and 0406 in
columns 48-51. The form for emission point 05 would contain 05 in
columns 19-20 and 0406 in columns 48-51. Point 06 would have 06 in
columns 19-20 and 0406 in columns 48-51. Each of the two points so
represented must be valid point ID's; that is, they must be all
numbers or letters and contain no blanks. Also, the NEDS point ID
must not be less than the lower point nor greater than the upper
point.
COMPLIANCE STATUS - COLUMN 52
Enter the present status of the source under existing legislation.
The valid codes are:
1 - Source is in compliance with existing legislation.
2 - Source is not in compliance, and no variance has been
given.
3 - Source is not in compliance, but a variance has been given.
4 - Compliance status is unknown.
COMPLIANCE SCHEDULE - COLUMNS 53-56
Enter the year and month by which the source must be in compliance.
This field is used for sources with compliance status of 2 or 3 (not
in compliance). The field must be numeric. The year (first two
characters) must not be more than 5 years greater than the year
entered on the option card.
COMPLIANCE UPDATE - COLUMNS 57-62
Enter the date (year, month, and day) of the most recent change in
the compliance status of the source. The field should be blank for
sources with compliance status of 4 (unknown). The field must be
numeric. The year (first two characters) must not be greater than
the-year entered on the option card.
57
-------
ECAP - COLUMN 63
Enter the status of the ECAP (emergency control action program) for
the source. Valid codes are:
0 - ECAP is not required
1 - ECAP required but not submitted
2 - ECAP has been submitted
Blank - Status unknown
CONTROL REGULATIONS - COLUMNS 64-75
Enter the air pollution control regulations that are in effect and
apply to the source. The field is currently not used by NEDS.
COLUMNS 76-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 12.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid on card 12.
This field must not be blank.
4.2.3 POINT RECORD CARD 13
COLUMNS 1-20
These fields are described in detail for plant record card 01 and
point record card 11.
POLLUTANT ID - COLUMNS 21-25
Enter the SAROAD parameter code for the pollutant whose emissions
are being measured. Refer to the AEROS Manual Series, Volume V:
Manual of Codes for a listing of SAROAD parameter codes. The entry
must be right justified, zero filled, with no blanks. The pollutant
58
-------
ID'S for the criteria pollutants and lead are 11101 (TSP), 42101
(CO), 42401 (S02), 42602 (NOX), 43101 (HC), and 12128 (lead).
CONTROL EQUIPMENT COST - COLUMNS 26-32
Enter the annual cost of maintenance and operation of pollution
control equipment (in dollars). Note that the triangle on the
coding form indicates an implied decimal point.
PRIMARY CONTROL EQUIPMENT - COLUMNS 33-35
Primary control equipment is any device whose main purpose is
reducing emissions of a pollutant and is reported as a primary
control using the codes listed in the AEROS Manual Series, Volume V,
Section 3.3.0. When none of the equipment codes appear to be
applicable, choose the code that most nearly resembles the actual
equipment and include a comment on card 14. Only control devices
that reduce the uncontrolled emissions normally associated with
the process should be reported. Do not report equipment that is a
normal part of the source activity even though the quantity of the
pollutants emitted may be reduced. For example, the recovery system
for coke by-product gases of a coke oven should not be reported as
pollution control equipment for hydrocarbons. Enter the appropriate
code or leave the field blank. For control equipment, enter the
code. For no control equipment, zero fill. If status is unknown,
leave blank. The entry must be right justified.
SECONDARY CONTROL EQUIPMENT - COLUMNS 36-38
Secondary control equipment is a device following, in a series,
another device designed to remove the same pollutant. For example,
a settling chamber (or gravity collector) for removing large
particles is often followed by an electrostatic precipitator. The
precipitator should be reported as secondary control equipment. A
device installed primarily for removal of one pollutant may also
remove another pollutant. In this case the code for the control
59
-------
device would be entered as primary control equipment for the
pollutant it is intended to remove and as secondary equipment for
the pollutant which it incidentally removes. When this situation
occurs, the control dev.ice would be entered in the secondary control
field with a zero entered in the primary control field for the
pollutant which is incidentally removed. Enter the appropriate code
or leave the field blank. For control equipment, enter the code.
For no control equipment, zero fill. If status is unknown, leave
blank. The entry must be right justified.
ESTIMATED CONTROL EFFICIENCY - COLUMNS 39-41
The overall collection efficiencies in weight percentage of all
control equipment at the source. Assume that the pollutant load
entering the control equipment is the normal, uncontrolled quantity
for that specific process. Note that the triangle on the coding
form indicates an implied decimal point.
ESTIMATED EMISSIONS - COLUMNS 42-48
Enter the annual, controlled emissions from the point source in tons
per year. Only values of 25,000 tons or less per year are valid.
Values between 25,001 and 800,000 tons per year cause a conditional
message to be printed but are accepted. Values above 800,000 are
rejected. The entry must be right justified.
MEASURED EMISSIONS - COLUMNS 49-55
Enter the actual measured annual, controlled emissions in tons per
year. The entry must be right justified.
ALLOWABLE EMISSIONS - COLUMNS 56-62
Enter the maximum emissions, in tons per year, that the source is
legally allowed to discharge into the atmosphere. Values above
25,000 will cause a conditional diagnostic message to be printed.
The entry must be right justified.
60
-------
EMISSIONS UNITS - COLUMN 63
This field is not used at present; in the future this field will
allow emissions to be coded in units other than the NEDS units.
ESTIMATION METHOD - COLUMN 64
Enter the method used to ascertain the estimated emissions. The
valid codes are:
0 - Not applicable (emissions are negligible)
1 - Stack test results or other emission measurement
2 - Material balance
3 - Calculated emissions using the Federal emission factor
4 - Guess
5 - Calculated emissions using a special emission factor other
than that given for the SCC
6 - New construction, not yet operational
7 - Facility closed, operations ceased
TEST METHOD - COLUMN 65
Enter any user-defined code for the method used to ascertain the
measured emissions. The field must be numeric.
COLUMNS 66-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 13.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
blank.
61
-------
4.2.4 POINT RECORD CARD 14
COLUMNS 1-20
These fields are described in detail for.plant record card 01 and
point record card 11.
NEDS P7 POINT COMMENT - COLUMNS ,21-72
Enter information to be transmitted on a NEDS P7 card. The entry
must be left justified.
COLUMNS 73-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 14.
ACTION CODE - COLUMN 80
Enter A (add), or C (change). D (delete) is not valid on a card 14.
This field must not be blank.
62
-------
4.3 SCC RECORD
The SCC record contains emission factor and identifying information for
an individual machine process for a point.
4.3.1 SCC RECORD CARD 21
COLUMNS 1-20
These fields are described in detail for plant record card 01 and
point record card 11.
SCC - COLUMNS 21-28
The ^purce Classification Code (SCC) identifies the type of
combustion or process. The code is an eight-digit number divided
into four levels (I, II, III, and IV) to assist in determining and
entering the correct process definition. Refer to the AEROS Manual
Series, Volume V: AEROS Manual of Codes, Section 2.7.0, for the SCC
codes. A maximum of 15 SCC's may be used to describe a point. The
entry must be right justified, zero filled, with no blanks.
SCC SEQUENCE NUMBER - COLUMNS 29-30
This field allows the user to specify duplicate SCC's for a given
point. If only one record is needed for an SCC, the SCC sequence
number should be 00. Additional records should be numbered. The
entry must be right justified, zero filled with no blanks.
BEC - COLUMNS 31-35
The first three characters indicate the basic equipment
classification code. The last two characters are used to number
units at the same source. The field must be numeric. A listing
of BEC codes can be found in the Air Pollution Manual of Coding: A
Coding System for Identification of Basic Equipment and Control
Devices Used in Industrial Processes, Peter Loquercio and Stanley,
U.S. Dept. of HEW, Public Health Service, National Center for Air
Pollution Control, 1968.
63
-------
FUEL UNITS - COLUMN 36
This field is not used at the present time. Future expansion of the
system will allow the user to specify the fuel process rate in units
other than the NEDS units.
FUEL, PROCESS, SOLID WASTE OPERATING RATE - COLUMNS 37-43
Enter the average annual fuel, process, or solid waste operating
rate. The emission factor file prescribes the units to be used for
each SCC. The entry must be right justified.
MAXIMUM DESIGN RATE - COLUMNS 44-50
Enter the maximum hourly design rate of the most important process
equipment, or the upper operating limit that generally would not be
exceeded in normal practice. Units are the NEDS units for the SCC
for the process, expressed as an hourly rate. Note that the
triangle on the coding form indicates an implied decimal point.
SULFUR CONTENT - COLUMNS 51-53
Enter the sulfur content for combustion processes, indicated as a
weight percentage. Note that the triangle on the coding form
indicates an implied decimal point.
ASH CONTENT - COLUMNS 54-56
Enter the ash content for combustion processes. The ash content is
indicated as a weight percentage. Note that the triangle on the
coding form indicates an implied decimal point.
HEAT CONTENT - COLUMNS 57-61
Enter the heat content for combustion processes, specified in
millions of BTU per SCC. The entry must be right justified.
64
-------
ASH-SULFUR ORIGIN - COLUMN 62
Enter the origin of the emission factor information related to the
SCC. This should match the EMF origin on SCC Record card 23. The
valid codes are:
F -Federal
S - State
L - Local
ASH-SULFUR SOURCE - COLUMN 63
Enter any user-defined code to specify individual local emission
factor information. This should match the EMF source on SCC Record
card 23. The value 'H1 is used to indicate that the emission is
hand calculated and that no emission factor insertion should take
place.
COLUMNS 64-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 21.
ACTION CODE - COLUMN 80 ,
Enter A (add), C (change), or D (delete). This field must not be
blank.
4.3.2 SCC RECORD CARD 22
COLUMNS 1-30
These fields are described in detail for plant record card 01, point
record card 11, and SCC record card 21.
CONFIDENTIALITY - COLUMN 31
Enter a code which indicates whether or not data for this source is
considered confidential; that is, not to be released to the public.
The codes are:
65
-------
1 - Source is confidential.
2 - Source is not confidential.
SOURCE CODE - COLUMN 32
Enter a code which identifies the process category for the SCC. The
val id codes are:
B - Boiler
P - Process
C - Other combustion unit
S - Solid waste
SOURCE DESCRIPTION - COLUMNS 33-57
Enter a brief description of the source. This field can also be
used for comments. The field must be coded for SCC's ending in 97,
98, or 99. The entry must be left justified.
COLUMNS 58-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 22.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid on card 22.
This field must not be blank.
4.3.3 SCC RECORD CARD 23
COLUMNS 1-30
These fields are described in detail for plant record card 01, point
record card 11, and SCC record card 21.
66
-------
EMF ORIGIN - COLUMN 31
Enter the origin of the emission factor information. This should
match the ash-sulfur source on card 21. The valid codes are:
F - Federal
S - State
L - Local
EMF SOURCE - COLUMN 32
Enter a user-defined code to specify individual local emission
factor information. This should match the ash-sulfur source on card
21. The value 'H1 is used to indicate that the emission is hand
calculated and that no emission factor insertion should take place.
POLLUTANT ID - COLUMNS 33-37, 49-53
Enter the SAROAD parameter code for the pollutant whose emission
factor information is being recorded. Refer to the AEROS Manual
Series, Volume V: AEROS Manual of Codes for a listing of SAROAD
parameter codes. The entry must be right justified, zero filled,
with no blanks. The pollutant ID's used for the criteria pollutants
and lead are 11101 (TSP), 42101 (CO), 42401 (S02), 42602 (NOX),
43101 (HC), and 12128 (lead).
EMISSION FACTOR - COLUMNS 38-46, 54-62
Enter statistical average of the rate at which a pollutant is
released into the atmosphere as a result of some activity. The
emission factors for each SCC can be found in the Compilation of Air
Pollutant Emission Factors, EPA Publication No. AP-42. Note that
the triangle on the coding form indicates an implied decimal point.
ASH-SULFUR CODE - COLUMNS 47, 63
Enter the code which indicates whether or not the ash or sulfur
contents are to be used in the calculation of the estimated
emissions. The valid codes are:
67
-------
A - Ash
S - Sulfur
Blank - neither
EMF UNITS - COLUMNS 48, 64
This field is not used at present; in the future this field will
allow emission factors to be coded in units other than the NEDS
units.
COLUMNS 65-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
Th.e columns are preprinted with the card number 23.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not be
blank.
4.3.4 SCC RECORD CARD 24
COLUMNS 1-30
These fields are described in detail for plant record card 01, point
record card 11, and SCC record card 21.
NEDS P7 SCC COMMENT - LEFT HALF COLUMNS 31-5:6
Enter information to be transmitted on the left half of the NEDS P7
card. The entry must be left justified.
COLUMNS 57-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 24.
68
-------
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid on card 24.
This field must not be blank.
4.3.5 SCC RECORD CARD 25
COLUMNS 1-30
These fields are described in detail for plant record card 01, point
record card 11, and SCC record card 21.
NEDS P7 SCC COMMENT - RIGHT HALF - COLUMNS 31-56
Enter information to be transmitted on the right half of the NEDS P7
card. The entry must be left justified.
COLUMNS 57-77
These columns are not assigned; leave blank.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 25.
ACTION CODE - COLUMN 80
Enter A (add) or C (change). D (delete) is not valid on a card 25.
This field must not be blank.
69
-------
4.4 COMMENT RECORD
The comment record contains any information the user might wish to keep
in his file which is not found on the other records, such as permits and
registration information.
4.4.1 .COMMENT RECORD CARD 30
COLUMNS 1-20
These fields are described in detail for plant record card 01 and
point record card 11.
P&R SEQUENCE NUMBER - COLUMNS 21-22
The P&R sequence number identifies a comment for a point. Each
point can have up to 99 comments, which are numbered sequentially by
a P&R sequence number. Each comment can contain up to 999 lines,
which are identified by a P&R line number (see the following field
description). Comments are added and/or changed by line number.
Individual lines can be deleted, or an entire comment can be deleted
by specifying a P&R line number of 000. The entry must be right
justified, zero filled, with no blanks.
P&R LINE NUMBER - COLUMNS 23-25
Each point can have up to 99 comments, which are identified by a P&R
sequence number. Each of those comments can .contain up to 999
lines, which are identified by a PAR line number. Each line of
comment is an individual record in the EIS/PS master file and can be
added, changed, or deleted. Lines .are numbered .sequentially within
an individual comment (P&R sequence number). The entry must be
right justified, zero filled., with no blanks.
L/R (COMMENT FLAG) - COLUMN 26
Enter an L for left or R for right half of a comment line. Each
half contains 51 characters.
70
-------
HALF COMMENT - COLUMNS 27-77
Enter information to be contained in the comment record. The entry
must be left justified.
CARD NUMBER - COLUMNS 78-79
The columns are preprinted with the card number 30.
ACTION CODE - COLUMN 80
Enter A (add), C (change), or D (delete). This field must not
be blank.
71
-------
5.0 EIS/PS Emission Factor Files
The EIS/PS emission factor file is used to insert emission facator
information into the master file transactions a:nd to generate master file
transactions when updates to the emission factor information is needed.
The emission factor description file is used to provide supplementary
description information on the emission factor file report.
Transaction types 1, 2, and 3 are used for updatin.g the emission factor
description file, and type-4 transactions are used for updating the emission
factor file. Therefore, the following transactions are required to add a new
SCC to the files: one type-1 transaction, one type-2 transaction, one type-3
transaction, and one or more type-4 .transactions. A maximum of 17 type-4
(pollutant) transactions is allowed by the program:, the first of which must
contain a zero pollutant ID. The type-4 .transaction containing the zero
pollutant ID allows the user to enter the ash and; sulfur contents for the
specified SCC. This transaction is automaticalTy generated by PCVNEEF
(EP0020) when converting NEDS transactions to EIS/PS emission factor file
transactions; however, the user is required to enter the values for ash and
sulfur contents since the NEDS transactions do not contain this information.
Whether generated by PCVNEEF (EP0020) or supplied by the user, this type-4
transaction must be present to add a new SCC to- the .files.
Changing data in existing emission factor description file records
requires a type-1, type-2, or type-3 transaction,, depending: on the data being
changed. Also, any combination of the three can be used to change data; in a
record. Any data field can be changed, except the k:ey field (the SCC number)..
However, the control date field is changed, by PIMEFAC, (EP0040) only if the
d-ate of the transaction is greater than the control date of the emission
factor description file record.
Changing data in: an existing emission factor file record requires a
type-4 transaction. Any data can be changed,, except the key fields (the SCC
72
-------
number, the origin, the source type, the pollutant ID, and the record date).
However, the control date field of the record- (not to be confused with the
record date field, which contains the record's creation date) is changed by
PEMEFAC (EP0040) only if the transaction date is greater than the control
date.
Data fields in the emission factor description file records or the
emission factor file records will not be changed if the corresponding data
fields on the change transactions are blank.
Deleting an SCC from the emission factor description file and the
emission factor file requires a type-1 delete transaction. This will cause
the description record and all pollutant records associated with the specified
SCC to be deleted from their respective files. Type-2 and type-3 delete
transactions are invalid and will be rejected by the program.
Deleting a single pollutant record from the emission factor file requires
a type-4 delete transaction. However, a type-4 delete transaction containing
a zero pollutant ID is invalid and will be rejected by the program. The only
way to delete an emission factor file record that contains a pollutant ID of
zero is to delete the entire SCC by submitting a type-1 delete transaction for
that SCC.
73
-------
5.1 EMISSION FACTOR TRANSACTIQNi CARP TYPE 1
CARD NUMBER - COLUMN 1.
This column is preprinted w^tth-. the card; number 1.
ACTION: CODE - COLUMN. 2 .
Enter A (add), C (change.)., or D (delete:).. Thrs; field should not be
left blank.
SCC. NUMBER - COLUMNS 3-10
Enter the: source classification! code number that describes the
process. Refer to the AEROS: Manual Series;, Volume; V: AEROS
Manual of Codes, Section 3.7.0, for-SCC numbers.. The: entry
must be right justified, zero filled,, with no: bl'anks.
COLUMNS 11-17
These fields are not assigned:- leaver blank.
DATE - COLUMNS 18-22
Enter the Julian date of the: trransact.ioni iln; the; form YYDDD. The
entry must be right justified!,, zero1 fil;Ted,: with; no blanks,.
NEDS CATEGORIES - COLUMNS 23-73-
Enter information pertaining; to1 the process; associated with a given
SCC. The field is divided into 4 subfieTds each' of which is 17
characters in length. The. 4 subfields. contain descriptions, of the 4
parts of the SCC number. The. fourth, sub.fieTd: is on card 2.. Refer
to the AEROS Manual Series,, Volume- Vc AEROS. Manual of Codes.,,
Section 3.7.0:,, for the given SCC.. The fields must be.1 left
justified.
COLUMNS 74-80
These columns are not used;- leaver blank.
7/4?
-------
5.2 EMISSION FACTOR TRANSACTIONS CARD TYPE 2
CARD NUMBER - COLUMN 1
This column is preprinted with the card number 2.
ACTION CODE - COLUMN 2
Enter A (add) or C (change). D (delete) is not valid on card 2.
This field should not be left blank.
COLUMNS 3-39
These fields are described in detail for card 1.
UNITS DESCRIPTION - COLUMNS 40-74
Enter information pertaining to the unit of measure code which
describes the units in which the emission factor is calculated.
Refer to the AEROS'Manual Series, Volume V: AEROS Manual of Codes,
Section 3.7.0, for the given SCC. The entry must be left justified.
Characters 1 to 35 are entered on card 2 and characters 36 to 69 are
entered on card 3.
COLUMNS 75-80
These columns are not assigned; leave blank.
75
-------
5.3 ;EMISSION FACTOR TRANSACTION CARD TYRE 3
CARD NUMBER - COLUMN 1
This column is preprinted with the card -number 3.
ACTION CODE - COLUMN 2
Enter A (add) or C .(change). D (delete) is not valid on card 3.
This field should not be left blank..
COLUMNS 3-22
These fields are described 1;n detail for iEmission Factor Transaction
card type 1.
UNITS DESCRIPTION - COLUMNS 23-56
The second !ha'lf of the UNITS DESCRIPTION TafonTraitton a:s described in
•detail for Emission Factor Transactions card type 2., columns -40-74
are entered here~
COLUMNS 57-80
These columns are not assii'fneoi.; l-ea,ve Ib'ilsmk..
-------
5.4 EMISSION FACTOR TRANSACTIONS CARD TYPE 4
CARD NUMBER - COLUMN 1
This column is preprinted with the card number 4.
ACTION CODE - COLUMN 2
Enter A (add), C (change), or D (delete). This field should not be
left blank.
SCC NUMBER - COLUMNS 3-10
Enter the source classification code number that describes the
process. Refer to the AEROS Manual Series, Volume V: AEROS Manual
of Codes, Section 3.7.0, for SCC numbers. The entry must be right
justified, zero filled, with no blanks.
ORIGIN - COLUMN 11 .
Enter the origin of the emission factor information. The valid
codes are: F - Federal
S - State
L - Local
SOURCE - COLUMN 12
Enter a user-defined code to specify individual local emission
factor information.
POLLUTANT ID - COLUMNS 13-17
The SAROAD parameter code of the pollutant whose emissions are being
measured. Refer to the AEROS Manual Series, Volume V: AEROS Manual
of Codes for a listing of SAROAD parameter codes. The entry must be
right justified, zero filled, with no blanks. The pollutant ID's
used for the criteria pollutants are 11101 (TSP), 42101 (CO), 42401
(S02), 42602 (NOX), 43101 (HC), and 12128 (lead).
77
-------
DATE - COLUMNS 18-22.
Enter the Julian date of the transaction in the form YYDDD. The.
entry must be right justified, zero fill.Ted;, with' no. blanks;.
POLLUTANT NAME - COLUMNS 23-42
Enter the actual name or the chemical: representation of the
pollutant referred to; by the pollutant ID., Refer to the AEROS
Manual Series, Volume V: AEROS Manual of Codes.. The field must be
left justified.
NEDS V FLAGS - COLUMNS 43-4,4
This field ts reserved for future use.; leave blank.
ASH FLAG - COLUMN 45
Enter the code to indicate whether or rrot the ash- content is to be
used; in. the calculation of the: estimated; emissions.. The vaTid codes
are: A1 - Ash content to, be used Bliank. - Ash; content not, to be used;
SULFUR FLAG - COLUMN. 46
Enter the code to indicate whether or not tie- sulfur content is to>
be used in the calculation1 of tire; estimated; emissions.. The valid-
codes are:
S -Sulfur content to: be used:
Blank -Sulfur content not t.o> be used
UNIT OF MEASURE - COLUMNS 47-48
This field is not used at present; in: tte future this field will
allow emission factors to be coded in uaiits other than: the NEDS
units. Leave blank..
EMISSION FACTOR; - COLUMNS 49-57
, Enter a statistica-l average of the rate at wMctv a pollutant ts
released into the atmosphere as a result of some activity. The
73
-------
field must be numeric. The emission factors for each SCC can be
found in Compilation of Air Pollutant Emission Factors, EPA
Publication No. AP-42. Note that the triangle on the coding form
indicates an implied decimal point.
ASH CONTENT - COLUMNS 58-60
Enter a weight percentage which indicates the ash content for
combustion processes. Note that the triangle on the coding form
indicates an implied decimal point.
SULFUR CONTENT - COLUMNS 61-63
Enter a weight percentage which indicates the sulfur content for
combustion processes. Note that the triangle on the coding form
indicates an implied decimal point.
CONTROL DEVICE EFFICIENCY - COLUMNS 64-66
Enter the overall collection efficiencies in weight percentage of
all control equipment at the source. Assume that the pollutant
load entering the control equipment is the normal, uncontrolled
quantity for that specific process. Note that the triangle on the
coding form indicates an implied decimal point.
CONFIDENCE LEVEL - COLUMN 67
Enter a user-defined vafue to show the reliability of the emission
factor. The field must be numeric.
COLUMNS 68-80
These fields are not assigned; leave blank.
79
-------
Appendi x~. A-\
ETS7AT Transact i on-: FreTd* Tab,! es.
The-following symbols are us'ed in-aOtabtles: ihnAppendtx1. A:
R - Requi red
Bla'rik -" Optional
X -- Not' ail 1 owed
N - Numeric
A - Alphanumeric
*' Field can be
deleted with *
C - Required, but not'mandatory (condit-fonaiP)'
W - Req'ui red, but not mandatory (warnfng;)"
-------
Table A-l. DESCRIPTION - CARD 1
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
DATE
AIR BASIN
SMSA
GEOGRAPHIC
NAME
MAJOR ACTIVITY
ASSOCIATED
PLANT ID
SIP BASE YEAR
PROJECTED YEAR
RURAL
POPULATION
PERCENTAGE
SUBALLOCATION
TYPE
G CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 14
15 - 19
20 - 22
23 - 26
27 - 46
47-66
67 - 70
71 - 72
73 - 74
75 - 76
77
78
79
80
LENGTH
2
4
3
5
5
3
4
20
20
4
2
2
2
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
A
A
A
A
N
N
N
A
A
N
A
ADD
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
X
X
X
X
X
X
X
X
R
R
R
R
FIELD
DELETE
*
*
*
*
*
*
*
*
81
-------
Table A-2. DESCRIPTION - CARD 2
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
POPULATION
AQCR NAME
SUBALLOCATION
TYPE
G CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - .2
3-6
7-9
10 - 14
15 - 22
23 - 76
.77
78
79
80
LENGTH
2
4
3
5
8
54
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
A ;
A
A
N
A
ADD
R
R
R
R
R
R
R
R
CHANGE
:R
R :
R
R
R
R
R
R
DELETE
R '.
R
R
R
X
X
R
R
R
R
FIELD
DELETE
*
*
82
-------
Table A-3. DESCRIPTION - CARD 3
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
SUBALLOCATION
TECHNIQUE
SUBALLOCATION
TECHNIQUE
DESCRIPTION
DEFINED AREA
CODE
SULFUR CONTENTS
ANTHRACITE COAL
BITUMINOUS COAL
DISTILLATE OIL
RESIDUAL OIL
ASH CONTENTS
ANTHRACITE COAL
BITUMINOUS COAL
UTM COORDINATES
ZONE
HORIZONTAL
VERTICAL
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 14
15 - 16
17 - 36
37-39
40 - 47
40 - 41
42 - 43
44 - 45
46 - 47
48 - 53
48 - 50
51-53
54 - 75
54 - 55
65 - 66
56 - 59
67 - 70
60 - 64
71 - 75
LENGTH
2
4
3
5
2
20
3
2l
21
21
21
31
31
2
2
41
4!
- 51
51
ALPHA/
NUMERIC
N
N
N
N
A
A
N
N
N
N
N
N
N
N
N
N
N
N
N
ADD
R
R
R
R
CHANGE
R
R
R
R
DELETE
R
R
R
R
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
FIELD
DELETE
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
one-digit decimal position is assumed.
83
-------
TABLE A-3. .DESCRIPTION - CARD 3
FIELD NAME
FILLER
SUBALLOCATION
TYPE
6 CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
76
77
78
79
80
LENGTH
1
1
1
1
1
ALPHA/
NUMERIC
NOT U!
A
A
N
A
ADD
IED
R .
,R
R
R
CHANGE
R
R
R
R
DELETE
R
I
R
R
R
FIELD
DELETE
84
-------
Table A-4. DESCRIPTION - CARD 4
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
UTM COORDINATES
ZONE
HORIZONTAL
VERTICAL
SOURCE TYPE
LENGTH OR AREA
LENGTH/AREA UNITS
CODE
SUBALLOCATION TYPE
G CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 14
15 - 58
15 - 16
26 - 27
37 - 38
48 - 49
17 - 20
28 - 31
39 - 42
50 - 53
21 - 25
32 - 36
43-47
54 - 58
59
60 - 66
67 - 68
77
78
79
80
LENGTH
2
4
3
5
2
2
2
2
A X
A i
41
A X
51
51
51
51
1
72
2
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
A
N -
A
A
A
N
A
ADD
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
X
X
X
X
X
X
X
X
X
X
X
X
. X
X
X
R
R
R
R
FIELD
DELETE
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
•'•A one-digit decimal position is assumed.
^A two-digit decimal position is assumed.
85
-------
Table A-5. DESCRIPTION - CARD 5
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
SIP ESTIMATES
TSP
S02
NOX
HC •
CO
; SUBALLOCATION. TYPE
.G CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 14
15 - 37
15 - 19
20 - 23
24 - 27
28 - 32
33-37
77
78
79
80
LENGTH
2
4
; 3
5
5
4
4
5
5
; l
1
1
1
ALPHA/
NUMERIC
N
N
; N
N
N
N
N
N
N
A
A
N
A
ADD
R
R
R
; R
R
R
R
' R
CHANGE
I R
! R
: R
R
R
R
R
R
DELETE
R.
R
R
R
X
X
X
X
X
R
R
R
R
FIELD
DELETE
*
*
*
*
*
86
-------
Table A-6. DESCRIPTION - CARD 6
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
SUBCARD NUMBER
POPULATION CODE
GAS FUEL, LIGHT
VEHICLES
GAS FUEL, HEAVY
VEHICLES
DIESEL FUEL, HEAVY
VEHICLES
VEHICLE MILES,
LIMITED ACCESS
VEHICLE MILES,
RURAL
VEHICLE MILES,
SUBURBAN
VEHICLE MILES,
URBAN
SUBALLOCATION TYPE
G CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 14
15
16
17 - 23
24 - 29
30 - 35
36 - 41
42 - 47
48 - 53
54 - 60
77
78
79
80
LENGTH
2
4
3
5
1
1
7
6
6
6
6
6
7
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
N
N
N
N
N
N
N
A
A
N
A
ADD
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
X
X
X
X
X
X
X
X
R
R
R
R
FIELD
DELETE
*
*
*
*
*
*
*
*
87
-------
Table ,A-7. DESCRIPTION- - 'CARD"I
FIELD NAME
.STATE
COUNTY
AQCR
SUB ALLOCATION
•NUMBER
POLLUTANT ID
POLLUTANT ID
POLLUTANT NAME
POLLUTANT NAME
ATTAINMENT STATUS
ATTAINMENT STATUS
AQMA NUMBER
AQMA NUMBER
SUB-ALLOCATION TYPE
G CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
"7-9
10 - 14
. 15 - 19
43 - 47
20 - 34
48 - 62
35
63
:3.6 - 41
•64 - 69
77
78
79
80
LENGTH
-2
4
"3
V5 ;
"5
:5
.15
.1-5
.1
1
6
:e
.1
1
:i
i
-.NUMERIC
*
.N
'N
•;N
N
N
vA
A
•A
-A
A
A
•A
A
N
-A
.ADD
•'R :'''
;R .-
"R J:
^R ;'.
R '
(R) .
:R :
-R i
R
:R
'CHANGE
R
R
R
-R
R
(R)
fi
R
R
R
DELETE
>R
'R
;R
R
R
00
X
'X
X
X
X
X
R
R
R
R
"FIELD .
/DELETE
*
*
*
-*
*
*
.88
-------
Table A-8. CATEGORY - CARD 1
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
CATEGORY NUMBER
CATEGORY DISAGGRE-
GATION NUMBER
CATEGORY
DESCRIPTION
YEAR OF INFORMATION
PROCESS RATE
CATEGORY ADJUSTMENT
VALUE
UNITS CODE
UNITS CODE
DESCRIPTION
SUBALLOCATION TYPE
DISAGGREGATION TYPE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 14
15 - 17
18-19
20 - 44
45 - 46
47 - 55
56 - 62
63 - 64
65 - 76
77
78
79
80
LENGTH
2
4
3
5
3
2
25
2
9
7
2
12
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
A
N
N
N
N
A
A
A
N
A
ADD
R
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
X
X
X
X
X
X
R
R
R
R
FIELD
DELETE
*
*
*
*
*
*
89
-------
Table A-9. CATEGORY - CARD 2
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
CATEGORY NUMBER
CATEGORY DISAGGRE-
GATION NUMBER
UNIFORM MONTHLY
THRUPUTS
MONTHLY THRUPUT
PERCENTAGE
HOURS PER DAY
DAYS PER WEEK
WEEKS PER YEAR
THRUPUT RATIO
MAXIMUM HOURLY
THRUPUT
DATA CONFIDENCE
RATING
NITROGEN CONTENT
SULFUR CONTENT
ASH CONTENT
HEAT CONTENT
SUBALLOCATION TYPE
DISAGGREGATION TYPE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 14
15 - 17
18 - 19
20
21 - 44
45 - 46
47
48 - 49
50 - 53
54 - 63
64
65 - 67
68 - 69
70 - 72
73 - 76
77
78
79
80
LENGTH
2
4
3
5
3
2
1
24
2
1
2
41
102
1
32
21
31
4
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
A
N
N
N
N
N
W
N
N
N
N
N
A
A
N
A
ADD
R ,
R :
R
•R ;
R
R
W
W
R
R
R
R
CHANGE
•R
R
R
R
R
R
R
R
R
R
'DELETE
•R
R
R
R
R
R
X
X
X
X
X
X
X
X
X
X
X
R
R
R
• R
FIELD
.DELETE
*
*
*
*
*
*
*
*
*
*
*
one-digit decimal position is assumed.
three-digit decimal position is assumed.
90
-------
Table A-10. CATEGORY - CARD 3
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
CATEGORY NUMBER
CATEGORY DISAGGRE-
GATION NUMBER
UNIFORM HOURLY
THRUPUTS
HOURLY THRUPUT
PERCENTAGES
SUBALLOCATION TYPE
DISAGGREGATION TYPE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 14
15 - 17
18 - 19
20
21 - 68
77
78
79
80
LENGTH
2
4
3
5
3
2
1
48
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
A
N
A
A
N
A
ADD
R
R
R
R
R
R
W
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
X
X
R
R
R
R
FIELD
DELETE
*
*
91
-------
Table A-ll. CATEGORY - CARD 4
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
CATEGORY NUMBER
CATEGORY DISAGGRE-
GATION NUMBER
NEDS A7 COMMENT
INFORMATION SOURCE
CODE
INFORMATION SOURCE
NARRATIVE
SUBALLOCATION TYPE
DISAGGREGATION TYPE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 14
15 - 17
18 - 19
20-53
54
55 - 74
77
78
79
80
LENGTH
2
4
3
5
3
2
34
1
20
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
A
A
A
A
: A
N
A
ADD
R
R
R
R
R
R
R :
. R
' R :
R
.CHANGE
R
R
R
R
R
R
R
; R
R
R
DELETE
R
R
R
R
R
R
X
X
X
R
R
R
R
FIELD
DELETE
*
*
*
i
92:
-------
Table A-12. CATEGORY - CARD 5
FIELD NAME
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
CATEGORY NUMBER
CATEGORY DISAGGRE-
GATION NUMBER
POLLUTANT ID
EMISSION FACTOR
EMISSION FACTOR
CONFIDENCE RATING
EMISSION FACTOR
ORIGIN
EMISSION FACTOR
SOURCE
POLLUTANT SPECIFIC
DATA
NEDS A7 EMISSION
POLLUTANT NAME
SUBALLOCATION TYPE
DISAGGREGATION TYPE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
• 3 - 6
7 - 9
10 - 14
15 - 17
18 - 19
20 - 24
25 - 34
35
36
37
38 - 47
48 - 54
55 - 69
77
78
79
80
LENGTH
2
4
3
5
3
2
5
101
1
1
1
10
7
15
1
1
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
N
N
N
A
A
A
N
A
A
A
N
A
ADD
R
R
R
R
R
R
R
W
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
X
X
X
X
X
X
X
R
R
R
R
FIELD
DELETE
*
*
*
*
*
*
*
three-digit decimal position is assumed.
93
-------
Table A-13. COMMENT RECORD
FIELD NAME-
STATE
COUNTY
AQCR
SUBALLOCATION
NUMBER
CATEGORY NUMBER
CATEGORY DISAGGRE-
GATI.ON NUMBER
LINE NUMBER
HALF COMMENT
R CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7 - 9
10 - 14
15 - 17
18 - 19
20-21
23 - 72
78
79
80
LENGTH
2
4
3
5
3
2
2
50
1 '
1
1
ALPHA/
NUMERIC
N
N
N
N
N
N
N
A
A
N
A
ADD
R
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
X
R
R
R
FIELD
DELETE
*
:94
-------
Table A-14. NEDS A6 COMMENT
FIELD NAME
STATE
COUNTY
AQCR
NEDS A6 COMMENT
N CODE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7 - 9
10 - 77
78
79
80
LENGTH
2
4
3
68
1
1
1
ALPHA/
NUMERIC
N
N
N
A
A
N
A
ADD
R
R
P.
R
R
R
CHANGE
R
R
P.
R
R
R
DELETE
R
R
R
X
R
R
R
FIELD
DELETE
*
95
-------
Appendix B:
EIS/PS Transaction Field: Tables
The following symbols are used tn alit tables, in Appendix B:
R - Requi red
Blank - Optional
X - Not allowed
N - Numeric
A - Alphanumeric
* Field can be
deleted with *
C - Required, but not mandatory (conditional)
W - Required,, but not mandatory (warning.)
96
-------
Table B-l. CARD 01 - PLANT INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
CONTROL
REGION
LOCAL
CONTROL
USER PLANT
ID
CITY
UTM ZONE
OWNERSHIP
CODE
CONTACT
PERSON
TELEPHONE
PRINCIPAL
PRODUCT
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 13
14 - 18
19 - 21
22 - 23
24 - 35
36 - 39
40 - 41
42
43 - 57
58 - 67
68 - 77
78 - 79
80
ALPHA/
LENGTH
2
4
3
4
5
3
2
12
4
2
1
15
10
10
2
1
NUMERIC
N
N
N
A/N
N
A
A
A
N
N
A
A
N '
A
N
A
ADD
R
R
R
R
R
C
v R
R
CHANGE
R
R
R
R
R
R
R
FIELD
DELETE
R
R
R
R
R
X
X
X
X
X
X
X
X
X
R
R
DELETE
*
*
*
*
*
*
*
*
*
97
-------
Table B-2-. CARD 0.2 - "PLANT INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NAME/
ADDRESS
NUMBER OF
EMPLOYEES
PROPERTY
AREA
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2 •
3 - 6
7 - 9
10 - 13
14 - 18
19 - 66
67 - 70
71 - 76
78 - 79
80
ALPHA/
LENGTH
2
4
3
4 '
5
48
4
61
2
1 '
NUMERIC
N .
N ,
N
A/N
N
A
N
:N
N
A
ADD
R
R
R
R
R
R
- 1
R
R
•CHANGE
R
•R
R
R
R
R
R
FIELD
DELETE
R
R
R
R
R
X
X
X
R
R
DELETE.
*
*
one-digit decimal position iis assumed,.
:98
-------
Table B-3. CARD 03 - PLANT INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
MAILING
ADDRESS
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 13
14 - 18
19 - 66
78 - 79
80
ALPHA/
LENGTH
2
4
3
4
5
48
2
1
NUMERIC
N
N
N
A/N
N
A
N
A
ADD
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
FIELD
DELETE
R
R
R
R
R
X
R
R
DELETE
*
99
-------
TabTe. B-4-., CARD; OS - PLANT' FT COMMENT'
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS P7
PLANT
COMMENT
CARD NUMBER
ACTION CODE.
RECORD
POSITIONS:
1 - 2.
3-6
7 - 9
; 10 - 13
, 14 - 18
! 19 - 70
78 - 79
; 80
ALPHA/
'LENGTH
2
4:
• 3:
4-
£
52
2
1
•NUMERIC;
' N>
N>
N
K/M
Ni
K
r N;
A
ADD
R<
R:
R;
: R
K
t
• K
: R-
.CHANGE:
• R'
R.
. R'
: Rr
R"
. R-
• R;
FIELD.
DELETE.
R
R
R
R
R
X
R
R
DELETE
*•
1005
-------
Table B-5. CARD 11 - POINT INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
USER POINT ID
SIC
IPP
UTM HORIZONTAL
UTM VERTICAL
LATITUDE
LONGITUDE
ANNUAL THRUPUT
OPERATING RATE
BOILER
CAPACITY
SPACE HEAT
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7 - 9
10 - 13
14 - 18
19 - 20
21 - 23
24 - 27
28 - 29
30 - 33
34 - 38
39 - 44
45-51
52 - 59
60 - 64
65 - 69
70 - 72
78 - 79
80
LENGTH
2
4
3
4
5
2
3
4
2
41
51
6
7
8
5
5
31
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
A
N
N
N
N
N
N
N
N
N
N
N
A
ADD
R
R
R
R
R
R
C
C
C
R
R
CHANGE
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
X
X
X
X
X
X
X
X
X
X
X
R
R
FIELD
DELETE
*
*
*
*
*
*
*
*
*
*
*
one-digit decimal position is assumed.
101
-------
Table B-6, CARD 12 - POINT INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
STACK HEIGHT
STACK DIAMETER
TEMPERATURE
FLOW RATE
VELOCITY
PLUME HEIGHT
POINTS WITH
COMMON STACK
COMPLIANCE
STATUS
COMPLIANCE
SCHEDULE
COMPLIANCE
UPDATE
ECAP
CONTROL
REGULATIONS
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 13
14 - 18
19 - 20
21 - 24
25 - 27
28 - 31'
32 - 38
39 - 43
44 - 47
48 - 51
52
53 - 56
57 - 62
63
64 - 75
78 - 79
80
LENGTH
2
4
3
4
5
2
4
31
4
7
5
4
4
1
4
6
1
12
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
N
N
N
N
N
N
A/N
N
N
N
N
A
N
A
ADD
R
R
R
R
R
R
R
R
•CHANGE
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
X
X
X
X
X
X
X
X
X
X
X
X
R
R
FIELD
DELETE
*
*
*
*
*
*
*
*
*
*
*
*
one-digit decimal position is assumed.
102
-------
Table B-7. CARD 13 - POINT POLLUTANT INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
POLLUTANT ID
CONTROL EQUIPMENT
COST
PRIMARY CONTROL
EQUIPMENT
SECONDARY CONTROL
EQUIPMENT
ESTIMATED CONTROL
EFFICIENCY
ESTIMATED EMISSIONS
MEASURED EMISSIONS
ALLOWABLE EMISSIONS
EMISSIONS UNITS
ESTIMATION METHOD
TEST METHOD
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 13
14 - 18
19 - 20
21 - 25
26 - 32
33 - 35
36 - 38
39 - 41
42 - 48
49 - 55
56 - 62
63
64
65
78 - 79
80
LENGTH
2
4
3
4
5
2
5
6
3
3
3l
7
7
7
1
1
1
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
N
N
N
N
N
N
N
N
N
N
N
N
A
ADD
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
X
X
X
X
X
X
X
X
X
X
R
R
FIELD
DELETE
*
*
*
*
*
*
*
*
*
*
one-digit decimal position is assumed.
103
-------
Table B-8. CARD 14 - POINT P7 COMMENT
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
NEDS P7 POINT
COMMENT
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1-2
3-6
7-9
10 - 13
14 - 18
19 - 20
21 - 72
78 - 79
80
LENGTH
2
4
3
4
5
2
52
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
A
N
A
ADD
R
R
R
R
R
R
R
R
CHANGE
R
R
R
•R
•R
R
R
R
DELETE
R
R
R
R
R
R
X
R
R
FIELD
DELETE
*
104
-------
Table B-9. CARD 21 - SCC INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
SCC
SCC SEQUENCE
NUMBER
BEC
FUEL UNITS
OPERATING RATE
MAXIMUM DESIGN
RATE
SULFUR CONTENT
ASH CONTENT
HEAT CONTENT
ASH-SULFUR
ORIGIN
ASH-SULFUR
SOURCE
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7 - 9
10 - 13
14 - 18
19-20
21 - 28
29 - 30
31 - 35
36
37 - 43
44 - 50
51 - 53
54 - 56
57 - 61
62
63
78 - 79
80
LENGTH
2
4
3
4
5
2
8
2
5
1
7
7l
32
33
5
1
1
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
N
N
N
N
N
N
N
N
N
A
A
N
A
ADD
R
R
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
R
X
X
X
X
X
X
X
X
X
R
R
FIELD
DELETE
*
*
*
*
*
*
*
*
*
three-digit decimal position is assumed.
two-digit decimal position is assumed.
one-digit decimal position is assumed.
105
-------
Table B-10. CARD 22 - SCC. INFORMATION
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
SCC
SCC SEQUENCE
NUMBER
CONFIDENTIALITY
SOURCE CODE
SOURCE
DESCRIPTION
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7 - 9
10 - 13
14 - 18
19 - 20
21 - 28
29 - 30
31
32
33 - 57
78 - 79
80
LENGTH
2
4
3
4
5
2
8
2
1
1
25
2
1
ALPHA/
NUMERIC.
N
N
N
A/N
N
A/N
N
N
N
A
A
N
A
ADD
R
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
R
X
X
X
R
R
FIELD
DELETE
*
*
*
106
-------
Table B-ll. CARD 23 - SCC POLLUTANT INFORMATION
FIELD* NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
SCC
SCC SEQUENCE
NUMBER
EMF ORIGIN
EMF SOURCE
POLLUTANT ID
EMISSION FACTOR
ASH-SULFUR CODE
EMF UNITS
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 13
14 - 18
19 - 20
21 - 28
29 - 30
31
32
33 - 37
49 - 53
38 - 46
54 - 62
47
63
48
64
78 - 79
80
LENGTH
2
4
3
4
5
2
8
2
1
1
5
5
yl
7!
1
1
1
1
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
N
N
A
A
N
N
N
N
A
A
N
N
N
A
ADD
R
R
R
R
R
R
R
R
R
R
(R)
R
R
CHANGE
R
R
R
R
R
R
R
R
R
(R)
R
R
DELETE
R
R
R
R
R
R
R
R
R
(R)
X
X
X
X
X
X
R
R
FIELD
DELETE
*
*
*
*
*
*
three-digit decimal position is assumed.
107
-------
Table B-12. CARD 24 - SCC P7 COMMENT
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
SCC
SCC SEQUENCE
NUMBER
NEDS P7 SCC
COMMENT -
LEFT HALF
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7 - 9
10 - 13
14 - 18
19 - 20
21 - 28
29 - 30
31 - 56
78 - 79
80
LENGTH
2
4
3
4
5
2
8
. 2
26
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
N
N
A
N-
A
ADD
R
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
R
X
R
R
FIELD
DELETE
*
-
108
-------
Table B-13. CARD 25 - SCC P7 COMMENT
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
SCC
SCC SEQUENCE
NUMBER
NEDS P7 SCC
COMMENT -
RIGHT HALF
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3-6
7-9
10 - 13
14 - 18
19 - 20
21 - 28
29 - 30
31 - 56
78 - 79
80
LENGTH
2
4
3
4
5
2
8
2
26
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
N
N
A
N
A
ADD
R
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
R
X
R
R
FIELD
DELETE
*
109
-------
TABLE B-14. CARD 30 - COMMENT
FIELD NAME
STATE
COUNTY
AQCR
PLANT ID
DATE
NEDS POINT ID
P&R SEQUENCE
NUMBER
P&R LINE NUMBER
L/R (COMMENT
FLAG)
HALF COMMENT
CARD NUMBER
ACTION CODE
RECORD
POSITIONS
1 - 2
3 - 6
7-9
10 - 13
14 - 18
19 - 20
21 - 22
23 - 25
26
27 - 77
78 - 79
80
LENGTH
2
4
3
4
5
2
2
3
1
51
2
1
ALPHA/
NUMERIC
N
N
N
A/N
N
A/N
N
N
A
A
N
A
ADD
R
R
R
R
R
R
R
R
R
R
R
CHANGE
R
R
R
R
R
R
R
R
R
R
R
DELETE
R
R
R
R
R
R
R
R
X
R
R
FIELD
DELETE
*
110
-------
Appendix C
EIS/AS Input Forms
111
-------
AGENCY.
EMISSIONS INVENTORY SYSTEM/AREA SOURCE (EIS/AS)
COMPREHENSIVE DATA HANDLING SYSTEM (COHS)
DESCRIPTION TRANSACTIONS 1-6
BY.
DATE
PAGE OF.
-T
A
T
E
1
- I
COUNTY
3
... 1. 1 1
AQCR
7
i i
SUBALLOC
NBR
10 14
i i i i
RATE
YR
15
DAY
17
1 1
AIR
BASIN
20
1 1
SMS A
23
i 1 1
GEOGRAPHIC NAME
27
1 1 1 1 I 1 I i I 1 I I I 1 I 1 1 1 I
MAJOR ACTIVITY
47
1 1 I 1 1 1 1 1 1 1 1 1 I 1 I 1 1 1 1
ASSOC
PLANT 10
67
1 1 1
SIP
BASE
YR
71
1
PROJ
YR
73
1
%
RUR
75
1
c/
s
77
78
G
N
B
R
/9
1
A
C
T
1
O
N
BO
POPULATION
15
,,_1_ J 1 1 1 1 1_
AQCR NAME
23
1 1 1 1 1 1 1 1 L _!__!_ J_._L 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 \ 1 1 1 1 1 1 1 1 1
C/
S
77
78
G
N
B
H
79
2
A
C
T
1
I)
N
80
SUB
TECH
15
i
;
SUBALLOCATION TECHNIQUE DESCRIPTION
17
1 1 1 1 1 1 1 1 1 1 t 1 1 1 { 1 1 1 1
DEF
AREA
CODE
37
1 1
SULFUR CONTENTS
ANTH
COAL
40
A
BUM
COAL
42
A
OIST
OIL
44
A
USIC
OIL
46
A
ASH CONTENTS
ANTH
COAL
48
1 A
BITUM
COAL
51
1 A
UTM COORDINATES
ZONE
1
54
t
HORIZ 1
56
1 1 A
VEHT1
60
1 t 1 A
ZONE
2
65
HORIZ 2
67
1 1 A
VERT 2
71
1 1 1 A
r.i
s
77
78
G
N
B
R
79
3
A
T
1
O
N
BO
PO
UTM COORDINATES
ZONE
3
15
HORIZ 3
1 7
1 1 A
VERT 3
21
1 1 1 A
ZONE
4
20
1
HORIZ 4
28
1 1 A
VEHT4
:i2
1 1 1 A
ZONE
5
37
(
HORIZ S
3U
1 1 A
VERTS
43
1 I 1 A
ZONE
6
4H
1
HORIZ 6
'.jU
i I A
VERT 6
54
1 1 1 A
S
U
R
C
E
5U
LENGTH OF LINE.
LINK. OR AREA
GO
1 1 1 1 A 1
LLA
UNITS
CODE
67
1 1 1 1 1 I 1
(V
S'
77
IB
G
N
R
R
79
4
A
C
T
1
N
BO
SIP ESTIMATES
TSP
15
1 1 1 1 • 1
S02
20
1 1 1
NOX
24
1 1 1
HC
2B
1 1 1 1
CO
113 37
1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
C/
S
7 7
IB
C
N
B
H
71J
5
A
C
T
N
80
S P
0 O
B f
Sjo
l^AC
LIGHT VEHICLE
GAS
17
^r 1 i 1.1 i i i. .
HEAVY VEHICLE
GAS
24
1 1 1 1 1
HEAVY VEHICLE
DIESEL
30
1 1 1 1 1
LIMITED ACCESS
ROADS/MVM
35
1 1 1 1 1
RURAL ROADS
MVM
42
111/11
SUBURBAN
ROADS/MVM
48
1 1 1 1
URBAN ROADS
MVM
54 6C
1 L_J 1 1 1
1 1 1 1 L_L__1 _!_!_ 1 ! _l_ L L _l_
C/
s
71
tf
G
N
d
R
70
6
T
O
N
HO
-------
AGENCY.
EMISSIONS INVENTORY SYSTEM/ARIA SOURCE (EIS/AS)
COMPREHENSIVE DATA HANDLING SYSTEM (CDHS)
DESCRIPTION TRANSACTION 7
BY
DATE.
PAGE.
-OF.
s
T
A
T
E
1
i
COUNTY
3
1 1 1
AQCR
7
1 1
SUBALLOC
NBR
10 14
I 1 1 1
POLLUTANT
ID
15
till
llll
1 1 1 1
llll
lilt
llll
llll
llll
llll
llll
POLLUTANT NAME
20
i i i i i i i i i i i i 1 i
i i i i i • i i i i i i i 1 i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i f i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
t i i i i i t i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i
i i i i i i i i i i i i i i
A
T
T
N
35
AQMA
NUMBER
36 41
1 1 1 1 I
l I I I I
1 1 1 1 1
1 I 1 1 I
.lilli
1 I I i I
1 i 1 I I
1 1 1 1 1
i i i i i
1 1 1 1 1
1 I 1 i 1
POLLUTANT
ID
43
llll
llll
llll
llll
llll
llll
llll
llll
llll
1 III
llll
POLLUTANT NAME
48
1 1 1 1 I 1 1 1 1 1 1 1 1 1
1 1 1 1 1 I 1 I 1 I 1 1 | 1
1 1 1 1 1 1 1 1 1 1 1 1 I 1
I 1 1 1 I 1 1 I I 1 I 1 I 1
I I I I i I 1 i i i I I i I
I I i I i i I I I I I 1 i I
I I I 1 I 1 I 1 1 i I 1 I 1
I i 1 1 I I I 1 1 I 1 1 I I
1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 i I 1 I I I I 1 1 1 I I 1
1 1 I 1 I 1 I 1 1 I 1 I 1 1
I i i I I i i i I i I i I 1
A
T
T
N
63
AQMA
NUMBER
64 69
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
i
I I I i I
1 I I i i
I I i i i
I i i i i
1 I i i i
1 I I I I
I i i i i
1 1 1 1 1
1 1 1 1 1
i i i i i
I I I I 1
i i I i I
1 1 1 1 1 |
I 1 1 I 1 1
1 1 1 1 1 1
1 1 1 1 1 1
I I I I 1 1
i I i i I |
i I I I I I
I I i I 1 I
I I i 1 1 I
I I I I 1 I
I i i I 1 I
1 1 1 1 1 1
1 1 I 1 1 I
i i i i i i
1 1 I 1 1 1
c/
s
77
78
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
N
B
R
79
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
A
C
T
1
0
N
80
-------
AGENCY.
EMISSIONS INVENTORY SYSTEM/AREA SOURCE (EIS/AS)
COMPREHENSIVE DATA HANDLING SYSTEM (CDHS)
CATEGORY TRANSACTIONS
DATE.
PAGE.
s
T
.A
T
•E
t
i
COUNTY
3
AQCR
7
SUBAUOC
NBR
10
1111
CATEG
NBR
15
DISAG
NBR
18
CATEGORY DESCRIPTION
20
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
YEAR
k5
i
PROCESS RATE
47
CATEGORY
•ADJUSTMENT
56
1 1 1 1 I 1
UNIT
CODE
63
. 1
.UNITS:CODE
DESCRIPTION
65
III Ill
C/
S
77
A/
D
78
N
R
'9
1
A
8
BO
U
^
M JAN
2C 21
,
MONTHLY THRUPUT PERCENTAGE
FEB
23
j
MAR
25
APR
27
1
WAY
29
JUN
31
1
JUL
33
I
AUG
35
1
SEP
37
|
OCT
39
NOV
41
DEC
43
HRS
PER
DAY
45
1
1?
A
K
47
:WKS
PER
YR
48
THRUPUT
RATIO
50
1 1 -A
MAXIMUM HOURLY
THRUPUT
54
C
0
N
F
u
NITRO
CONT
65
. 1 1
SULF
CONT
68
A
ASH
CONT
7O
1 A
HEAT
CONTENT
73
1 1 t
C/
S
77
A/
0
78
A
.. Q
N T
" i
R 8
79 SO
_2
1
F
R 0
1
1
'
2
l
3
L
4
l
5
1
E
7
1
8
1
HO
9
l
URIY
10
1
THRU
11
1
PUTP
12
. 1.
ERCEH
13
J .
TAG!
14
15
l
IE
l
17
i
18
i
19
l
20
i
21
22
1
23
t
1 1 1 1 1 1 1
C/
S
Al
0
N
B
H
,
A
1
N
NEDS A7 COMMENT
20
S
.R
k
*4
SOURCE .OF INFORMATION NARRATIVE
55 '4
,
C/
s
77
HI
0
78
N
R
R
bs
4
?
1
N
80
POLLUTANT
ID
20
1 1 1 1
lilt
1 1 1 1
1 1 1 1
1111
till
1111
1 I I I
1 1 1 1
1111
1111
III)
| 1 1 1
till
EMISSION FACTOR
25
1 1 1 1 1 1 A. 1 1
1 t I I I I A I I
1 1 1 I 1 t A t t
1 1 1 1 1 1 A I 1
1 1 1 1 t 1 A 1 1
1 1 1 1 1 1 A 1 1
1 1 1 1 1 1 A 1 1
1 1 1 1 1 1 A 1 1
1 1 1 1 I 1 A 1 1
1 1 1 1 1 1 A 1 1
1 1 1 1 1 1 A 1 1
1 All
1 1 t 1 1 1 A 1 1
1 1 1 1 1 1 A. 1 1
1 1 1 1 1 I A 1 1
0
N
F
35
0
R
G
36
R
C
37
POLLUTANT
SPECIFIC DATA
38
tti
lltlillll
It
1 1 I I I I i I i
1 I t 1 I I I l I
t i i i i I i i r
i l t i
I 1 I I I 1 1 i I
litlliiil
1 I I 1 I 1 I 1 I
I 1 I 1 i i i i i
1 Li LI ' ' ' 1
NEDSA7
EMISSION
46
1 1 I 1 I 1
1 1 1 1 1 1
1 1 1 1 1 1
1 I 1 1 1 1
1 1 1 1 1 1
1 1 1 1 1 1
— 1 _ 1 ^^ 1 J 1 —
POLLUTANT NAME
55 69
1 1 1 1 1 1 t 1 1 1 1 1 1 t
1 1 1 — 1 — l — 1 1 — l i L i i -l i ...
1 l t 1 i 1
_i i t l i .J
C/
s
77
Ay
D
78
N
B
R
79
l)
ij
1
s
s
Cj
-------
AGENCY.
I
1
1
COUNTY
3
1 l_ 1_
AQCR
7
1 1
SUBALLOC
NBR
10
1 1 1 1
CATEG
NBfl
15
1 1
DISAG
NBR
18
I
EMISSIONS INVENTORY SYSTEM/AREA SOURCE (EIS/AS)
COMPREHENSIVE DATA HANDLING SYSTEM (COHS)
COMMENT TRANSACTIONS
DATE
PAGE OF_
LINE
NBR
HALF COMMENT
I I I I 1
t i I t I i I i I I i t I I I 1—I i I I I I I i I I i I I I I i t ) t I I I I I—1—L
I I I I I i I I i I i I I 1__1 1 1 1 1 1 1 L
I I I I I I I I 1 | | I I I 1 I 1 1 1—I—1--I I I I I I I I I 1—I—I 1 1—I 1—I—I—I—I—I 1—L
I lillllllllllllllli.il I I I I 1_J 1 1 1
I I I I I I I I
I I I I I I I
I I I I t I I I I t I I I 1
1 I I I I I I I I
I I I I I I I t I
1 I I I I I I I I I I I I I I I I I 1 I I I I
II Ill
J 1 1 1 1 1 1 1 1 1 1 I__J 1 1 1 1 1 1 1 1 1 1 1 1 1 i I i I I 1 I I I I I I I I I I
I I 1 I 1
J I I I I I
I I I I I I 1 1 I I I I I I I I I 1 I 1 1 1 1 1 1 1 I I I I I I I I I I I I I
_l_l I I I I
J—I—I—I—I—i—I—i—I—I—I—I—I—i—i—i—i I—I—i—i—L_I—i i r i i i i i i i i i i i
i I I
i—i—i—i—i—i—i—i—i—i—i—i—i— i
_1 1—I—I—1—I—1—I—I—I—1—I—I—I I I I L
I t
I I I I
I I I
J—I 1 I 1 i
I I
J—I 1—I—I—I—I—I—I I I I I I I I I I I I I
J 1—I I I L
115
-------
EMISSIONS INVENTORY SYSTEM/AREA SOURCE (EIS/AS)
ACENC
S
A
T
1
I
i
i
i
i
i
i
i
i
i
i
i
i
i
i
i
i
i
v COMPREHENSIVE DATA HANm INn SVSTFMirnMtt BY
COUNTY
3
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
f 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
t 1 1
1 1 1
1 1 1
1 1 1
.1 1 1
III,
, , 1
AQCR
7
1 1
1 1
1 1
1 1
1 1
1 1
1 p
1 1
1 1
1 1
1 1
1 1
1 i
1 1
1 1
1 1
1 1
.1 V
1
1 1 '
1 1
1 1
1 1
Ml OS Afi r.OMMFNT n»TF
oi'r.f ,nr
NEDS A6 COMMENT
10
1 1 1 I I 1 1 1 1 I I i > 1 I I I i i i I I i I I I 1 l l l l i i l i i i l l i l l l l l i i i i i i i i i i i i | | |
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 I 1 1 I 1 I I 1 I 1 1 I I 1 I I I I 1 l l I I I 1 I 1 1 1 1 1 1 1 1 1 i I 1 1 I 1 I i | i
1 I 1 I I 1 1 I 1 I i i i i i i l i l i l > i i i i l l i i i i i i i i i i l ill
l l l i l l i l l i l i i l i i l i l i i i i t l i l i i i i i i i l i i l i i l i i l i l i l l i l i i 1 l l 1 l l l l 1 l i i ) i
l l 1 l l l l l 1 > l i i i i i l i l i i l i i i i l i i i i i i i l i i i i i l i i l i i i i l i l l l l l l l i l l l 1 l i i i i
l l l l l l l l l i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i
i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i l t l i i i
I 1 1 I 1 1 I I | i I i i i i i I i I i i i i i I i i i i i i i I i I i i i i i i i i i i I I I I I I I I I i i I i ] I I I I 1 i i i
l 1 1 1 1 1 1 1 1 l l 1 1 1 l l l l l l 1 i 1 l l l i l l i l i l 1 l 1 1 1 1 1 l 1 l l l ill
I 1 I i I I 1 1 I I 1 i I 1 i I i i 1 i i i i i I i I l i l i i i i i l i i i l l l l l i l l i i i i l i l l l l i i l l l
l l 1 l l i i i i i i i l i i i i i i i i i i i i i i i i i i i i i i i i i i i i i t i i i i i l i i i i i i i i i i l i l i l i i l
t l l l l l l l i i i i i i i i i i i i i l i i i i i | i i i i i i ii iii i i i i i i i i i i i i i i i i i i i i i i i i i ill
1 1 1 1 I 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 i 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I i 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 | | 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 ! 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 | | | | | 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 l 1 1 l l 1 1 1 l l 1 l l l 1 i l 1 l 1 l l 1 Ii
1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 1 1 | 1 1 1 1 | l 1 l 1 1 1 1 1 1 1 1 1 1 1 l l l 1 1 l 1 l l 1 l l l l 1 l 1 1 | | | | | | l i 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II
7fl
N
N
r,i
N
N
N
N
M
N
N
N
N
N
N
N
N
N
N
N
N
N
N
70
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
JL
A
T
1
o
N
HO
-------
T
A
T
E
i
COUNTY
3
1 1 l
SUBALLOC
7
CATEG
NBR
12
DISAG
NBR
15
DATE
YH
24
DAY
70
l l
a
FLAGS
N
7°
S
:u
A
:n
NITRO
CONT
32
SULF
CONT
35
1 A
ASH
CONT
38
1 A
CATEGORY DESCRIPTION
41 G!>
N
p
R
79
t
c
T
1
O
N
BO
COUNTY NAME
29 4B
1 t 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
N
R
/o
1
C
T
1
0
N
35
occo
1 7
S
R
C
R
POLLUTANT
ID
9
1 1 1 1
1 1 1 1
till
1 1 | 1
1 | t 1
1111
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 ' 1
1 1 1 1
1 I I 1
till
1 1 1 1
EMISSION FACTOR
29
t 1 I I I 1 A 1 l
1 1 1 1 1 1 A 1 1
1 1 1 1 1 1 A 1 1
I I 1 1 1 1 A 1 I
1 t 1 1 1 1 A 1 |
1 1 1 1 1 1 A 1 1
| 1 1 1 1 1 A 1 1
1 I 1 1 1 1 A 1 1
1 1 1 1 1 1 A 1 1
1 1 1 1 I 1 A 1 1
1 1 1 1 1 t A 1 1
1 1 1 1 1 1 A 1 1
1 1 1 1 1 1 A t 1
| i i i i i A i i
1 1 1 1 1 1 A 1 1
1 1 I 1 1 1 A 1 1
)
N
F
n
POLLUTANT NAME
10
i i i i i i i i i i i 1 i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i i i i i i i i i
i i i i i i t i i i i i i i
i i | i i i i i I i i i I I
t i i i i i i | i i i i i i
i i i I I i i i i i i i I I
i i i i i i i i i i i i i i
i i i i t i i i i i i i i i
i i i l i i i i i i i i i i
I i i I I I I 1 1 I I i I I
POLLUTANT
SPECIFIC DATA
55 G4
1 I 1 1 1 1 1 1 1
1 I 1 1 1 1 t 1 1
I 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1
i I I 1 1 I 1 1 I
1 1 1 1 1 1 1 1 I
1)1111111
1 1 1 1 1 1 1 1 1
1 1 1 1 1 \ 1 1 1
1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1
t 1 1 1 1 1 1 1 t
i i I I i i I 1 I
1 1 1 1 1 1 1 1 1
1 j I 1 1 1 1 1 1
1 1 1 1 1 1 I 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 t 1
1 1 1 1 I 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1
I 1 1 1 1 L 1 1 1 1 t 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 t 1
1 1 1 1 1 1 1 1 1 1 1 1 1
| 1 1 1 1 1 1 1 1 1 1 1 1
i r i i i i i i i i l l l
1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 t I 1 1
N T
8 '
R N
2 L
j_
j_
j_
j_
3
_i
_i
3
.
-------
IGFNCV '
SEE BACK OF FORM FOR VALID CODES
i
8
$ iSlSlE l LlElClT
USER
KEYWORD
10 13
1 1 1
D
E
S
C
15
c
A
T
17
C
0
M
M
19
EMISSIONS INVENTORY SYSTEM/AR
COMPREHENSIVE DATA HANDLIN
RETRIEVAL SPECIFICA
SUBJECT NAME
i
i i l l
l l 1 l
i i i i i
i i i i
i l i i
l l l l
i i i l
i i i i i
i i i i i
i i i i i
i i i i i
i i i t i
i i i i
i i i i
i i i i
1 8
SlSlElN ID
I I
I I
I I
I I
1 1
1 1
1 1
1- 1
1 1
1 1
1 1
1 1
1 1
1 1
1
1 1
1
1
1
I
1
|
1
1
1
1
1
1
1
1
1
1 1 1 1
1 1 1 1
till
till
1 1 1 1
1 1 1
1 | 1 1
1 1 1 1
1 1 1 1
1 1 1 1
till
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 1
1 1
1 1
1 1
I |
1 1
1 1
1 1
1 I
1 I
1 1
1 1
1 1
1 1
1
1 I
1
1
1
1
1
1
1
1
1
1
1
1
1 1
1 1
1 1
i 1
1
1 1
1 1
t 1
1 1
1 1
1 1
1 1
1 1
|
(
|
|
|
|
|
|
|
|
l
t 1
I |
1 1
| t
1 i
1 1
t
1 l
I l
I |
I |
I 1
1 1
I |
|
|
|
|
|
|
|
|
|
|
|
|
31
I I I I I I 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1
N
F
33
R
0
35
—
-
EASQURCF (FIS/AS) ' «*
r. svsTFMfCnHS) DATE
TIONS ' paRF Of
OBJECT NAME (LITERALS MUST BE ENCLOSED IN SINGLE QUOTES)
37 67
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 t 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 1 1
I 1 I 1 1 1 I 1 1 1 I 1 1 1 I 1 1 1 1 1 1 1 1 1 1 1 1 I 1 I
i i i I I I I 1 I 1 1 1 1 1 1 I I I I I I 1 I 1 1 I 1 1 1 I
f | 1 I 1 1 I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
i I I I I I 1 1 1 1 1 I 1 1 1 I 1 I 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
I I 1 I ( 1 1 1 1 1 1 1 1 1 1 I I I I 1 1 I 1 t t 1 1 1 1 t
BO
69 71
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
-------
EMISSIONS INVENTORY SYSTEM / AREA SOURCE (EIS/AS)
RETRIEVAL SPECIFICATIONS
PAGE 2
VALID VALUES FOR
NEGATION FLAG GREATER THAN
-------
ro
o
EIS/AS QUICK LOOK RETRIEVAL
1 a
,|,|S|E,L|E|C|T
REPORT TITLE
10 "
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
73 BO
1 I/I I I/L.I
SELECTION CRITERIA
1 3
,1|0
v,o
1,0
1,0
1,0
V
1|0
1,0
1,0
V
(
4
DATA
ABOn
6 9
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1, 1 1
1 1 1
flEt
or
1 1
VALUE
1J 24
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 l> 1 I- 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 ll 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
}
AND/OR
1 1
1 1
1 |
1 1
1 1
1 1
1 1
1 1
I !
1 1
1,0
1,0
1,0
1,0
1,0
1,0
1,0
1,0
1,0
1,0
(
DATA
ABBR
i i i
I i i
i i i
III
I I I
1 1 1
...1 1 I _
1 I I
I i i
ill
REL
Of
1 1
VALUE
13 24
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
i i i i i i i i i i :
ill i i i i i
ill i i i i i
ill i i i i i
MI i i i t i<
iii i i i i i
i t i t i i till
)
?b
AND/OR
?B 30
1 1
1 1
1 i
1 1
1 1
1 1
1 1
1 1
1 1
1 .1
RELATIONAL
OPERATORS:
E-EQUAL
U -UNEQUAL
G- GREATER THAN'
L- LESS THAN
P-PRESENT
8-BLANK
AND/OR MUST BE'
BLANK ON1 LAST 10
CARD
REPORT TYPE
REPORT CODES:
SU - POLLUTANT SUMMARY REPORT
O'L - QUICK LOOK[R'EPOnf
REPORT1 ORDER
1 J
3|°
DATA
ABBR
* '
1 1 1'
iX
•
DATA
ABBR
-10 13
III
X
.14
DATA
ABBR
16 14
III
X
20
DATA
ABBR
73 3*
' 1 1 1
X
jt
DATA
ABBR
IB 11
1' 1 I'
X
JV
DATA v
ABBR ,
;I4 M IB
'III
ENTER DATA ABBREVIATIONS LEFT TO RIGHT
ENTER' X FOR PAGE BHEAK/SUBf OTALLING
QUICK LOOK REPORT FORMAT
1 3
4|0
ABBR
4 I
\ \ \
1-
B
ABBR
10 .13
1 1 1
|4
ABBH
Id 19
t 1 1
t
j-g
ABBR
22 2'J
1 1 1
h
fif
ABBR
2B 31
1 1 1
H
-1?
ABBR
34 }l
-11 1:
•>9
ABBR
411 ' 4J
1 1 1
»-
44
ABBA
46 «'l
1 t I
S
!.<)
DATA
ABBR
12 i!>
1 I1 i
S
DATA
ABBR
4« bl
1 1 1
g
li?
POLLUTANT SUMMARY REPORT FORMAT
1 3
V
ABBR
4 7
t 1 1
ABBR
9 12
1 1 1
ABBR
14 17
1 1 1
ABBR
19 22
-i1 i i
ABBfl
J4 2/
1 1 1
ABBR
79 3?
1 1 1
ABBH
J4 Ji-
ll I
POLLUTANT SUMMARY REPORT POLLUTANTS
I J
'I1
ID
• •
I' 1 1 1
(D
10 !«
1 1 1 1
•to
It. JO
1 1 1 1
ID
2? 7U
1 1 1 1
ID
21 J2
MM
ID
Mil
-------
Appendix D
EIS/PS Input Forms
121
-------
AGENCY
s
T
A
T
E
1
L
COUNTY
3
1 1 1
AQCR
7
1 1
PLANT ID
NUMBER
10
I 1 I
DATE OF
RECORD
YR
14
|
DAY
18
1 1
EMISSIONS INVENTORY SYSTEM / POINT SOURCE (EIS / PS)
COMPREHENSIVE DATA HANDLING SYSTEM (CDHS)
PLANT RECORD (SEGMENT O) TRANSACTIONS
BY _
DATE.
PAGE
OF
CON-
TROL
REGION
19
I |
LOCAL
CON-
TROL
22
I
USER PLANT ID
24
I I I I 1 . I 1 1 1 | 1
CITY
36
1 1 1
UTM
ZONE
40
1
O
W
IM
F
R
42
CONTACT PERSON
43
1 1 1 1 1 1 I 1 1 1 1 1 1 1
TELEPHONE
58
1 i 1 i 1 1 1 1 1
PRINCIPAL PRODUCT
68
I i I . i I Mil
CARD
NBR
78
0| 1
A
C
T
o
N
80
rv>
1
ESTABLISHMENT NAME AND ADDRESS
19
i i i i i i i i i I i i i i I i i i i ,i i i. i 1 i. i i i i .1 i. i i t I i i i i i i 1 ,i .1 i i..
NUMBER
OF
EMPLOYEES
67
...I l-.i..
PROPERTY
AREA
71 ,.
II I I A
CARD
NBR
78
0,.2
A
C
I
N
80
ESTABLISHMENT MAILING ADDRESS
19 . .CO
I I I I I I I I I I I I I I I I 1 I 1 I 1 1 ! I I I 1 I 1 I | 1 I 1 I I i i i I i I i I i i, I
1 i 1 1 1 1 1 1 1 1
CARD
NBR
78
°l3
A
C
1
O
.N
hn
i
NEDS P7 PLANT COMMENT . .
19 . 70
II 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 i 1 1 1 1 1 1 1 I i I ( I 1 1 1 1 1 1
IIL i. j_
CARD
NBR
78 .
0 J4
A
C
T
n
N
80
-------
AGENCY.
EMISSIONS INVENTORY SYSTEM/POINT SOURCE (EIS/PSI
COMPREHENSIVE DATA HANDLING SYSTEM (CDHSI
POINT RECORD (SEGMENT 1) TRANSACTIONS
BY .
DATE.
PAGE.
s
T
A
E
1
|
...
COUNTY
3
1 1 1
AQCR
7
1 1
PLANT
ID NBR
10
1 1 1
DATE OF
RECORD
YR
14
|
DAY
1 1
NEDS
PO'NT
in
19
1
USER
POINT
ID
T.
1 1
SIC
T
\ 1 1
IPP
28
|
UTM
HORIZ
30
1 1 A
UTM
VERT
34
1 1 1 A
LATITUDE
DFC
39
|
MIN
|
SEC
|
LONGITUDE-
DEG
45
1 1
MIN
|
SEC
|
"a ANNUAL THRUPUT
DEC-
FES
52
|
MAR
MAY
|
JUN-
AUG
|
SEP-
NOV
|
OPERATE
RATE
HR
60
|
D
WK
|
BOILER
CAPACITY
6b
1 1 1 1
SPACE
HEAT
70
1 A
1 I 1 1
CARD
\'BH
78
M '
A
c
0
N
so
STACK DATA
HEIGHT
?1
1 1 1
DIAM
25
1 A
TEMP
2E
1 1 1
FLOWRATE
32
1 I 1 1 1 1
VELOCITY
3°
till
PLUME
HEIGHT
44
1 1 1
POINTS
WITH
COMMG'J
STACK
48
|
|
C
O
M
P
^.->
COMP
SCHED
YR
53
|
MO
|
COMPLIANCE
UPDATE
VR
57
|
MO
|
DAY
|
E
C
P
6.}
CONTROL REGULATIONS
REG 1
64
1 1 1
REG 2
1 1 1
REG 3
7B
1 1 1
|
CARD
NBB
78
1 | 2
C
T
1
0
N
SO
POL' L'TANT
ID
21
1 1 1 1
1 1 I 1
1 1 1 1
I 1 1 1
III!
1 1 1 1
1 1 1 1
I'll
1 1 1 1
MIL
1 1 1 1
1 1 1 1
1111
1 1 I 1
1 1 1 1
MIL
CONTROL
EQUIPMENT
COST
26
1 1 1 1 A 1
1 1 II A 1
II II A 1
1 1 II A 1
II 1 1 A 1
II 1 1 A 1
II 1 1 A 1
II 1 1 A 1
II 1 1 A 1
II 1 1 A 1
II 1 1 A 1
II 1 1 A 1
II 1 1 A 1
II MAI
II II A 1
II 1 1 A 1
PRIV-
CNTRL
EOL'lf
33
1 1
1 1
1 1
| |
1 1
1 1
I |
, ,
1 1
| |
1 1
1 1
1 1
I |
I |
1 !
SECNOV
CNTRL
EQUIP
36
1 1
1 1
1 1
| 1
1 1
1 1
I |
| |
J |
1 1
1 1
1 1
1 |
1 1
I |
EST
CONTRC"..
FfF
39
1 A
1 A
1 A
| ^
1 A
1 A
I A
| ^
1 A
| A
1 A
1 A
1 A
1 A
1 A
1 A
EMISSIONS,
ESTIMATE
J?
1 1 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
11 lilt
II 1 1 1 1
II 1 1 1 1
II 1 1 1 1
II 1 1 1. 1
M 1 1 1 1
MEASURED
EV'SSIONS
4?
1 M 1 1 1
1 1 1 1 1 1
1 1 1 1 1 1
1 1 1 1 1 1
1 M 1 1 I
1 1 1 I I 1
I 1 1 1 II
1 1 1 1 M
1 I I 1 II
I 1 1 I II
1 1 1 i I 1
1 1 1 1 1 1
1, 1 1 1 II
1 1 1 1 1 1
till 11
ALLOWABLE
EMISSIONS
56
III 1 M
III III
III III
1 1 1 1 M
III III
I I 1 1 1 1
1 I I 1 1 1
1 i i 1 1 I
I I 1 I 1 1
I t'l I 1 I
1 M I 1 1
1 I I 1 II
1 1 1 1 M
1 1 1 I II
1 I I 1 1 1
I i I I II
E
U
N
T
:r
E
S
T
\d
l>
f
S
T
V
65
M M 1 1 M 1 M
II 1 1 1 1 1 1 1 1 1
1 1 I i II 1 1 1 M
i i i 1 i i 1 1 M 1
II I I 1 1 1 1 1 1 1
1 i 1 1 I 1 1 1 1 1 1
M 1 II 1 1 1 1 M
1 i I t 1 1 Mill
1 M 1 1 1 1 1 1 1 1
i I 1 1 1 I Mill
1 M 1 I 1 1 II 1 1
1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 M 1 1
t 1 II I 1 1 1 1 1 1
L'ARC
\8R
1'f
M3
1 1:
1 \:
1 r
T
1 1 -
'1 ~
T;
'1 :
i I ;
'1
1 r-
M
' 1 ':
'!•'•
!| .-.
-------
AGENCY
EMISSIONS INVENTORY SYSTEM/POINT SOURCE (EIS/PS)
COMPREHENSIVE DATA HANDLING SYSTEM (CDHS)
SCC RECORD (SEGMENT 2) TRANSACTIONS
BY
DATE
PAGE
OF
STATE
1
|
COUNTY
3
I I I
AQCR
7
| |
PLANT
ID NBR
10
I I I
DATE
OF RECORD
YR
14
1
DAY
1 1
NEDS
POINT
ID
19
1
SCC
1
21
II
1
III
1 1
IV
1
SCC
SEQ
NBR
29
I
BEC
NO
31
1 1
ID
|
F
U
N
1
T
36
FUEL PROCESS
SOLID WASTE
OPERATING RATE
37
1 1 1 1 1 1
MAXIMUM
DESIGN RATE c
44
1 1 1 A 1 1
SULFUR
CON-
TENT
51
A I
ASH
CON-
TENT
54
I A
HEAT
CONTENT
57
I I I I
0/9
O
R
G.
62
A/S
S
•R
C
63
I I I I I I I I I I I! I
CARC
NBR
78
2|l
|
80
c
o
F
31
3
H
C
fc
32
SOURCE DESCRIPTION
33 57
1 1 1 1 1 1 1 1 1 I I I I I I I I I I I I I I I
I I I I I I I I I I I I I I I I I I I
CARD
NBR
78
2|2
A
V
N
80
EMFEMF
POLLUTANT
ID
EMISSION FACTOR
POLLUTANT
ID
EMISSION FACTOR
CARC
NBR
31
32
33
38
47
48
49
54
63
64
78
80
I I I I I A I I
I I I I I I I I
2|3
I A I I
I I I I
I I I I I A I I
I I I I I I I I I
2|3
111
I I A I I
I I I I I
I I I I I I I I I
2|3
I I I I
I A I I
I I I
A I
I I
ill
I I I I
I I I A I I
I I I I I A I I
I I I I I
2|3
I A I I
I I I I I I I I I
2|3
I I I I
I A I
I I I
I I I I A I I
213
A I I
I I I
I I I I I A I I
I I I I I I I I I I I I
2[3
213
I I I I I
1 I
I I I I I I I I I
211
I I I I I A I I
I I
I I I I I I I I I I I I
2|3
I I I I I A I I
J I
I I I I I I I I I
213
I I I I I A I I
I A I I
I I I
I I I I
213
A I
I I I I
A I I
I I I I I I I I I I I I
213
I I I I
1 III I A I I
II I I I A I I
213
NEDS P7 SCC COMMENT- LEFT HALF
31 56
I I I I I I I I I I I I I I I I I I I I I I I I I
I I I I I I I I I I I I I I I I I I I I
JA
7
IMBFT
78
2|4
8
80
NEDS P7 SCC COMMENT -RIGHT HALF 124
31 56
I I I I I I I I I I I I I I I I I I I I I I I I I
I I I I I I I I I I I I I I I I I I I I
CARD
NBR:
78
2f5
"F
"r
"ft
80
-------
AGEN
STATE
1
|
FMISSIONS INVENTORY SYSTEM /POINT SOURCE (FIS/ PS) BY
COUNTY
3
1 1
rrm/lPRPHFNSIVE DATA HANDLING SYSTEM (CDHS) n^TF
COMMENT RECORD (SEGMENT 3) TRANSACTIONS
DATE
PLANT OF RECORD POINT
AQCR ID NBR YR DAY ID
7 10 14 19
1 1 1 1 1 1 1 1 1
PNR
SEQ
NBR
21
1
1
|
1
1
1
I
|
1
1
1
|
1
1
1
1
|
1
1
|
LINE
NBR
23
1 |
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 I
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
LI
R
26
HALF COMMENT
27
1 1 1 1 1 1 1 1 I 1 1 1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 | 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 1 1 II 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
II III .1 II 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1
1 | 1 1 1 1 1 II 1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 !'l 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 till 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
II III 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 III 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I- 1 1 1 1 1 1 1 1 1 1 | 1 1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 II 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1
'ill 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 | 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
CARD
NBR
78
3,*
3 \SS
3|,
3|J»
3|*
3|*
3\ff
3\H
3|jr
3 1 a
3|*
3|flT
3|*
3|*
3|*
3|jr
3|(J
3|«r
3|*
3|*
-------
AGENCY.
EMISSIONS INVENTORY SYSTEM/POINT SOURCE (EIS/PS)
COMPREHENSIVE DATA HANDLING SYSTEM (CDHS)
EMISSION FACTOR FILE TRANSACTIONS
BY
DATE-
PAGE.
OF
NEDS CATEGORY 1
23
I
I
I I I I
I I I
I
NEDS CATEGORY 2
40
I I
I I I I I
I I
I
NEDS CATEGORY 3
57 73
M I M M I I
NEDS CATEGORY 4
23
|
I I I I I I
I I I I I I I I
NEDS UNITS 1 -35
40
74
I I I I M I I I I I I I I I I I I I I I I I I I I I I I M I I I
NEDS UNITS 36 -69
23
56
E
1
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
c
T
1
O
^
8
11
C
12
POLLUTANT
ID
13 17
0|0|0|0|0
1 1 1 1
1 1 1 1
Mil
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 1
1 1 1 1
III!
MM
MM
MM
II II
POLLUTANT NAME
23 42
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 II 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 M 1 1 1 1 II 1 1 1 1 1 1
III 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
III 1 1 1 1 1 1 1 II 1 1 1 1 1 1
1 1 1 Ml 1 1 1 1 1 1 I 1 1 1 1 1 1
1 1 1 1 1 1 1 1 M 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
III 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 M
1 1 I I 1 1 I I 1 1 I 1 1 I 1 l 1 1 1
III 1 1 1 1 1 1 1 II M 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 II 1 1 1 M 'l
1 1 1 1 1 1 II 1 1 1 1 1 1 1 1 1 1 1
M 1 1 1 1 1 1 II 1 1 1 II 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
FL/
V
43
|
,
•
1
|
|
|
|
|
|
|
!
1
1
,
,
|
\c
A
45
S
s
46
U M
N E
1 A
T S
47
|
|
|
|
|
|
|
|
1 :
l
l
!
l
i
i
i
1
EMISSION
FACTOR
49
1 1 1 1 IA 1 1
1 1 1 1 IA 1 1
1 1 1 1 1 A II
1 1 1 1 1 A 1 1
II 1 1 1 A 1 1
1 1 1 1 1 A 1 1
1 1 1 1 1 A 1 1
1 1 1 1 IA! 1
1 1 1 1 lAl 1
II 1 1 IA 1 1
1 1 1 1 1 Al 1
1 1 1 1 1 A 1 1
II M 1 A 1 1
1 1 1 1 1 Al 1
1 1 1 1 1 Al 1
1 II MAM
M M 1 All
ASH.
CNT
58
1 A
| A
1 A
| A
| A
I A
I A
| A
| A
|A
|A
j A
| A
I A
1 A
1 A
| A
SUL
CNT
61
A |
Al
Al
Al
Al
Al
A 1
Al
Al
Al
Al
A 1
Al
Al
Al
Al
Al
CDEF
64
| A
IA
1 A
1 A
1 A
1 A
1 A
|A
IA
IA
lA*
1 A
IA
IA
1 A
1 A
IA
1
67
i
126
-------
AGENCY
' SEE BACK OF FORM FOR VALID CODES
EMISSIONS INVENTORY SYSTEM / POINT SOURCE (EIS / PS)
COMPREHENSIVE DATA HANDLING SYSTEM (CDHS)
RETRIEVAL SPECIFICATIONS
BY
DATE.
PAGE.
OF
1
$ | $ | S | E | L | E
8
I c IT
' USER
KEYWORD
10 13
I I 1
COPY MEMBER NAME
16
23
I I I I 1 1 I
r\3
SUBJECT NAME
I i i i i i i I i i i i i i i i i i i i i
i i i I i I I I I I
i I I I I I i
I I I I I I I I I I I M I I I I I I I I
31
I I
I I I I I I I
i i i i i i i i i i i i
III I I I I I I I I I I I I
I I I I I I I I I I I I I I I I I I I I I
I I
I I I I I I I I J I I I I I I I I I I I I
1
I I
i i i i i i i i i i i i i i i i i i i i i r i i i i
1 1
i i i i i i i i i i i i i i i i i i
i
MI i i i i
I I I M I I I I I I I I I I I I I I I I I I I I I I I J_l
OBJECT NAME (LITERALS MUST BE ENCLOSED IN SINGLE QUOTESI 67
37
I I I I I I I I M I I I I I I I I I I I I I I I I 1
1 1 1 1 1 1 1 1 1 |
1 1 1
1 1 1
1 1
1 1 1 1 1 II 1 1 1 1 1 1 1 1 1 II 1 1 1 1 1 1 1
1 M 1 1 1 1 1 1 1
| 1 1 1 M 1 1 1 1 1 1 1 1 1 1
M 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 M 1 1 1 1 1 1 1 1 1 1 1
1 M 1 1 1 1 1 1 1
1 M 1 1 1 1 1 1 1
i i 1 i 1 1 i 1 1
1 | 1 1 II 1 1 i i i 1 i i | |
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 | 1 I 1 | 1 1 II 1 1 1 I 1 1
1 1 1 1 | 1 1 1 1 1 1 1 1 1 1 1 1 | 1 1 1 1 |
1 1 1 1 1 1 1 1
1 1 1 1 1 1
1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1
B o
69 71
I I
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1
$ I $ I E 1 N
5
D
-------
EMISSIONS INVENTORY SYSTEM / POINT SOURCE (EIS/P.S)
RETRIEVAL SPECIFICATIONS
PAGE.2
VALID VALUES FOR
NEGATION FLAG INF):
BLANK. N
RELATIONAL OPERATOR (RO):
"EQUAL
>GREATER THAN
< LESS THAN
BOOLEAN OPERATOR (BO):
AND. OR. BLANK
TYPE: N - NUMERIC
A = ALPHABETIC
PLANT RECORD DATA NAMES
NAME
AOCR
CITY
CONTACT
COUNTY
DATE-OF-O-RECORD
LOCAL-CONTROL
NUMBER -OF-EMPLOYEES
OWNER
PLANT-ID
PRINCIPAL -PRODUCT
PROPERTY-AREA
RECORD-O-DAY
RECORD -O-YEAR
SEG-O-ID
STATE
TELEPHONE
USER-CONTROL-REGION
USER-PLANT-ID
UTM-ZONE
LENGTH
3
4
15
4
5
2
4
1
4
10
6(1)
3
2
1
2
10
3
12
2
TYPE
N
N
A
N
N
A
N
A
A
A
N
N
N
N
N
N
A
A
N
COMMENT RECORD DATA NAMES
NAME
OATE-OF-3-RECORD
LINE-NBR
PNR-SEQ-NBR
RECORD-3-DAY
RECORD -3-YEAR
SEG-3-IO
SEG-3-POINT-ID
LENGTH
5
3
2
3
2
1
2
TYPE
N
N
N
N
N
N
A
POINT RECORD DATA NAMES
NAME
ANNUAL-THRUPUT_
BOILER-DESIGN-CAPACITY
COMPLIANCE-SCHEDULE
COMPLIANCE-STATUS
COMPLIANCE -STATUS-UPDATE
CONTROL-REGULATIONS
DATE-OF-1-RECORD
DAY-WEEK
DEC-FE.B
DIAMETER
ECAP
FLOW-RATE
HEIGHT
HORIZONTAL
HOURS-DAY
IPP
JUN-AUG
LATITUDE
LATITUDE-DEGREE
-LATITUDE -MINUTE
LATITUDE -SECOND
LpNGITUDE
LONGITUDE -DEC REE
LONGITUDE -MINUTE
LONGITUDE -SECOND
MAR-MAY
NBR-OF-POLLUTANTS
NEDS-POINT-ID
NORMAL-OPERATING
PLUME
POINTS-PER-STACK
RECORD-1-DAY
RECORD-1-YEAR
REG-1
REG-2
REG-3
SCHEDULE-MONTH
SCHEDULE-YEAR
SEG-1-ID
SEP-NOV
SIC
SPACE-HEAT
STATUS-DAY
STATUS-MONTH
STATUS-YEAR
TEMPERATURE
USER-POINT-ID
UTM-COORDINATES
VELOCITY
VERTICAL
WEEK-YEAR
LENGTH
8
5
4
1
6
12
5
1
2
3(1)
1
7
4
4(1)
2
2
.2
6
2
2
2
7
3
2
2
2
2
2
5
4
4
3
2
.4
4
.4
.2
2
1
2
.4
3(1)
2
2
2
4
3
-.9
5
5(1)
2
TYPE
N
N
N
N
N
N
N
N
•N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
A
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
A
N
N
N
N
POINT REPEATING DATA NAMES
•NAME
ALLOWABLE
CNTL-E QUIP-COST
CONTROL-EQUIPMENT
EMISSION-UNITS
EST-CONTROL-EFF
ESTIMATES
ESTIMATION-METHOD
MEASURED
POLLUTANT-ID
POTENTIAL
PRIMARY-CNTL
SECONDARY^CNTL
TEST-METHOD
LENGTH
7
7(2)
6
1
3(1)
7
1
7
5
7
3
3
1
TYPE
N
N
N
N
N
N
N
N
N
N
N
N
N
SCC RECORD DATA NAMES
NAME
ASH-CONTENT
BEC
BEC-ID
BEC-NUMBER
•CONFIDENTIALITY
DATE -OF -2- RE CORD
EMISSION-F.ACTOR-SOURCE
FUEL-PROCESS-RATE
FUEL-UNITS
HE'AT-CONTENT
MAX-DESIGN-RATE
NUMBER-OF-EF
RECORD-2-DAY
RECORD-2-YEAR
SCC
SCC-I
SCC-II
see-in
.SCC-IV
.SCC-SEQ-NBR
SEG-2-ID
SEG-2-POINT-ID
SOURCE-CODE
SOURCE -DESCRIPTION
SULFUR-CONTENT
LENGTH
3(1)
5
2
3
1
5
1
7
1
5
7(3)
2
3
2
8
1
2
3
2
2
1
2
1
25
3(2)
TYPE
N
\
I
N
A
N
N
N
N
N
N
N
N
N
N
N
N
N
N
A
A
A
N
NUMBERS IN PARENTHESES INDICATE
ASSUMED DECIMAL POSITIONS
128
-------
EIS/PS QUICK LOOK RETRIEVAL NAME DATE
1 R
S|S
s
E|L|E
C|T
REPORT TITLE
10 _. «
1 1
1 1 1 1 1 1 1 1 1 1 1 1
1
1 1
SELECTION CRITERIA
1 2
1,0
1,0
1,0
1,0
1,0
1,0
1,0
1,0
1,0
41,0
(
4
DATA
AUDR
b
0
1 1
1 1
1
1
1
1 1
1 1
1 1
1 1
i 1
REL
OP
11
VALUE
13 24
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 I 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 I 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
)
AND/OR
I I
I I
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1 1 1
1
1 1 1 1 1 1 1 1 1 1 1 1
1 1
1 1 1 1 1 1 1 1 1 1 1
1 ?
1,0
1,0
1,0
1,0
1,0
1|0
1,0
1,0
1,0
1,0
(
4
DATA
ABBH
<> 9
1 1 1
1 1 1
1 1 1
III
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
REL
OP
11
VALUE
U 24
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1
).
2i
AND/OR
21 30
1 L
1 1
1 1
1 i
1 J
1 1
1 1
1 1
1 1
1 1
RELATIONAL
OPERATORS:
E - EQUAL
U - UNEQUAL
L - LESS THAN
F- PRESENT
B- BLANK
AND/OR MUST BE
BLANK ON LAST 10
CARD
^OUTPUTS
1 1
2,0
RPT
CODE
4 b
|
RPT
CODE
/ 8
|
REPORT CODES:
OL - QUICK LOOK REPORT
TA - TURNAROUND DOCUMENT
REPORTORDER
I ?
3,0
DATA
ABBR
4 ;
1 1 1
X
a
DATA
ABBR
10 13
1 1 1
X
14
DATA
ABBR
16 19
1 1 1
X
JO
DATA
ABBR
?2 ~>5
1 1 1
X
?b
DATA
ABBR
ra Ji
1 1 1
X
3?
DATA
AiiR
.14 31
I I 1
X
38
AF -ANSWER FILE
ENTER DATA ABBREVIATIONS LEFT TO RIGHT
ENTER X FOR PAGE BREAK/SUBTOTALLING
QUICK LOOK REPORTS
t 7
4|0
4,1
4,2
SUP
PRES
DATA
ABBR
li 0
1 1 1
1 1 1
1 1 1
H
o
h-
1 (1
DATA
ABBR
ir r>
1 1 1
1 1 1
1 1 1
K
o
(-
II.
DATA
ABBR
li* ;l i
1 1 1
1 1 1
1 1 1
S
H
:•/
DATA
ABBR
.•M 71
\ 1 1
1 1 1
1 1 1
r-
o
t-
.'«
DATA
ABBfl
in I (
l I i
1 1 l
l i i
5
M
DATA
ABIR
li, l<)
1 1 1
1 1 1
1 1 1
H
O
>-
41)
DATA
ABIR
47 4?)
1 1 1
1 1 1
1 1 1
t-
O
H
4I>
DATA
AMR
4H b I
1 1 1
1 1 1
1 1 1
5
i>r
DATA
AMR
•>-i 'j /
1 i l
l 1 1
1 1 1
K
o
H
SH
DATA
AIIR
1.0 "1
111
1 1 1
1 1 1
H
S
(J*
ENTER X FOR SUP-
PRESSION OF DE-
TAIL LINES AND
FOR TOTALS
-------
EIS/PS QUICK LOOK RETRIEVAL
PAGE 2
JATA ELEMENT
ABBRE-
VIATION
POSITION IN-
MASTER FILE
DATA ELEMENT LENGTH li
IN MASTER
FILE
IN QUICK ;
LOOK REPORT.
** H
IN QUICK 0
LOOK -REPORT]
IF TOTALLED||DATA ELEMENT
ABBRE-
VIATION
POSITION IN
MASTER FILE'
DATA 'ELEMENT LENGTH
IN MASTER
.FILE
IN QUICK
LOW. REPORT
• •
IN QUICK
LOOK REPORT
IF TOTALLED
DATA ELEMENTS COKMON TO ALL SEGMENTS
iQCft
County
Plant
Segnent Date
Segment Day
Segccnt ID
Segnent Year
State
AQCR
CNTY
PLNT
DATE
OAYY
SEGM
YEAR
STTE
50
46
53
57
59
57
62
44
3
4
4
5
3
2
1
2
5
5
5
6
5
5
5
S
POINT SEGMENT DATA ELEMENTS (continued)
DATA ELEMENTS COKMON TO POINT. SCC. and COMMENT SEGMENTS
NEDS Point ID
NPID
63
2 1 5
1
State
Throughput
Throughput /Dec-Feb
Throughput /Jun-Aug
Throughput /Mar-May
Throughput /Sep-Nov
Jser Point ID
UTM Coordinates
:UTM Horizontal
UTM Vertical
Velocity
1STT
THRU
WMTR
SUW
SPNG
FALL
UPID
UTMC
HORZ
VERT
VELO
44
96
96
100
98
102
65
74
74
78
135
2
8
2
2
2
• 2
3
.9
4
-5
5
5
9
5
5
5
t
5
10
6
7
6
PLANT SEGMENT DATA ELEMENTS Repeating Point Segment Data Elements (POLL must be specified)
AQCR
City
Contact
Count/
.oca) Control
tailing Address
Ian and Address
lo. of Employees
Ownership
'lant 10
•Hncipal Product
'roperty Area
I Segaent Date
1 Segnent Day
\ Segaent 10
j Segnent Year
: State
| Telephone
Jser Control Region
User Plant ID
iTH Zone
PAQC
CITY
CONT
PCNT
ICON
HAIL
NAAD
NUHE
OWNS
CPLN
PROD
PROP
fl)TE
0DAY
BSEG
DYER
0STT
TELE
UCON
UPLT
UTMZ
50
82
89
46
68
182
124
172
88
S3
114
176
57
59
62
57
44
104
65
70
86
3
4
IS
4
2
48
48
4
1
4
10
6
5
3
1
2
2
10
3
12
2
S
S
16
S
5
49
49
5
5
S
11
8
6
5
5
5
5
11
5
13
5
9
Control Equipment
Control Equip. Cost
Emission Units
Euissions Allowable
Emissions Estimate
Emissions Measured
Est Control Efficiency
Estintion Kethod
Pollutant ID
jPrimary Control Equip
Secondary Control Equip
13 [Test Method
CEQP
CCST
EUNT
ALLO
ESTI
HE AS
ECEF
ESTH
POLL*
PCTL
SCTL
TSTH
2S3
246
290
276
262
269
2S9
291
241
253
256
292
6
7
1
7
7
7
3
1
5
3
3
1
7
9
5
8
8
8
5
5
6
5
5
5
14
13
13
13
SCC SEGMENT DATA ELEMENTS
'AQCR
Ash Content
BEC code
BEC ID
BEC Nuaber
Confidentiality
.County
Emission Factor .Source
POINT SEGMENT DATA ELEMENTS Fuel Process 'Rate
ACC6
Boiler design Capacity
;ontrol Regulations
;ontro; Regulation I
Zontrcl Regulation 2
lontrcl Regulation 3
;or.pl lance Schedule
loop. Schedule Year
:haust Flow Rate
; IPP Code
i .atltude
.atltude Degree
.atitude Minute
.atltude Second
.ongitude
.ongitude Degree
.ongitude Minute
Longitude Second
NEDS Po'int ID/SEGMENT
Norual Operating Rate
Number of Pollutants
Plant 10
Pluoe Height
Point IDs
Points «/ Common Stack
Segaent Date
Segccnt Day
Segwnt 10
Segnent Year
SIC Cede
Space Heat I
Stack Data
Stack Diameter
Stack Height
Stick Teiaperature
1AQC
SOIL
CREG
KES1
REG2
REG3
CSCH
SCHY
SCHM
csrr
CUPD
CUDY
CUMN
CUYR
1CNT
ECAP
FLOW
IPPC
LATT
LATD
LATH
LATS
LONG
LOND
LONM
LONS
5110
NORM-
NUMP
1PLN
PLUM
PTIO
PWCS
10TE
1DAY
1SEG
IYER
SICC
SPAC
STAD
DIAM
HGHT
TEMP'
50
1C9'
160
160
164
168
149
149
151
148
153
157
155
153
46
159
128
72
83
83
85
87
89
89
92
94
63
104
239
53
140
63
144
57
59
62
57
68
114
117
121
117
124
3
5
12
4
4
4
4
2
2
1
6
2
2
2
4
1
7
2
6
2
2
2
7
3
2
2
2
S
2
4
4
5
4
5
3
1
2
4
3
27
3
4
4
b
11
13
5
5
5
5
5
5
5
7
5
5
5
5
5
8
5
7
5
5
S
8
5
5
5
S
6
5
5 .
S
6
5 •
6
S
S
5
S
5
28
5
5
5
Fuel Units
11 Heat Content
Maximum Design »ate
NEDS Point ID/Segrcnt 2
No. of Emission Factors
Plant ID
{Source Class. Code
Sec i
isCC 2
SCC 3
JSCC 4 :
ISCC 'Sequence Number
Segment Date
Segment Day
Segment ID
Segment .Year
Source Code
Source Description
State
Sulfur Content
2AQC
ASHC
BECC
•BECI
BECN
CONF
•2CNT
EMFS
FPRT
FUNT
HEAT
MDRT
S2ID
NEMF
2PLN
.SCCC
SCC1 '••
SCC2
SCC3I
SCC4
SSQN
2DTE
2DAY
2SEG
.2YER
SRCC !
SRCD
2STT
SULC
aO
98
75
78
75
106
46
133
81
80
101
88
63
197
53
65
65
66
68
71.
73
'57
59
62
57
107
108
44
95
' 3
3
5
2
3
1
4
1
7
1
5
7
2
2
4
8
1
2
3 '
2
2
5
3
1
2
1
25
2
3
3
5
6
5
5
£
5
c
8
5
r.
;
5
5
5
9
5
S
5
5
5
6
5
5
5'
5
26
5
5
13
14
j
1
i
i
I
REPEATING SCC SEGMENT DATA ELEMENTS (KPID oust 'be specified)
Ash/Sulfur .Code
[mission Factor
Emission Factor .Units
Pollutant ID
ASSC
EMFA
EHFU
HPID*
214
204
215
.199
1
9
1
S
S
11
5
6
—
COMMENT SEGMENT 'DATA-ELEMENTS
AQCR
tfORIDGfltS
County
Left Coment
Line Number
NEDS Point .ID/Segment 3
Plant ID
PNR Sequence Number
Right Comment
Segment Date
Segment Day
Segment ID
Segment Year
3AQC
COMM
3CNT
LCHT
LINE
5310
3PLH
SEQN
RCMT
30TE
3DAY.
3SEG
3YEH
50
71
46
71
67
63
S3
65
122
57
59
62
47
3
102
4
51
3
2
4
2
51
5
3 .
" 1
2
5
99
5
52
5
.5
5
5
S2
-• 6
5
5
5
)
i
|
\
i
• -Relational Operator Must Be E
*• Only fields having an entry In this column are eligible for totalling.
. 1 denotes zero
130
-------
TECHNICAL REPORT DATA
(Please read Instructions on the reverse before completing)
1. REPORT NO. 2.
EPA 450/4-81-009
4. TITLE AND SUBTITUE
The Comprehensive Data Handling System
(CDHS) Coding Manual
7. AUTHOR(S)
The Research Triangle Institute
Research Triangle Park, North Carolina
9. PERFORMING ORGANIZATION NAME AND ADDRESS
Office of Air Quality Planning and Standat
Monitoring and Data Analysis Division
National Air Data Branch
Research Triangle Park, North Carolina 2~i
12. SPONSORING AGENCY NAME AND ADDRESS
U.S. Environmental Protection Agency
Office of Air, Noise and Radiation
Office of Air Quality Planning and Standar
Research Triangle Park, North Carolina 21
3. RECIPIENT'S ACCESSION-NO.
5. REPORT DATE
February 1981
6. PERFORMING ORGANIZATION CODE
8. PERFORMING ORGANIZATION REPORT NO.
10. PROGRAM ELEMENT NO.
-ds
11. CONTRACT/GRANT NO.
'711 68-02-3011
13. TYPE OF REPORT AND PERIOD COVERED
Final
14. SPONSORING AGENCY CODE
------- |