Asbestos in the Home
U.S. Consumer Product Safety Commission U.S. Environmental Protection Agency

-------
      Asbestos in the Home

i n
I n
I g
- II L
I U
. II I
1
11
1L
[i
I
JL
II

      August 1982
      U.S. Consumer Product Safety Commission
      U.S. Environmental Protection Agency
l-'or sale by the Superintendent of Documents. L' S Government Printing Office
            Washlncton. o C. 20402

-------
Introduction
This booklet was prepared by the
U.S. Consumer Product Safety
Commission (CPSC) and the En-
vironmental Protection Agency
(EPA). Its goal is to help consumers
understand the possible hazards of
exposure to asbestos and materials
containing  asbestos in the home.
The booklet describes asbestos,
where it may be found in the home,
and the possible dangers of expo-
sure to asbestos. The Table of Con-
tents lists the questions answered
in this booklet. If you have addi-
tional questions, you may call the
toll-free number listed at the back of
the booklet.
The Federal government is con-
cerned about asbestos-containing
products in the home because
sometimes asbestos fibers can be
released from these products. If as-
bestos fibers are inhaled, certain
types of cancer may later develop.
Asbestos in homes poses several
problems. Household members
have little or no protection from ex-
posure to asbestos fibers. Once re-
leased, the asbestos fibers may
stay suspended in the air for many
hours. After they settle, fibers can
be stirred up again by a household
activity, such as sweeping. During
this time, asbestos fibers can be in-
haled. This continued presence
could cause an ongoing risk in the
home.
EPA and CPSC have already taken
several steps to reduce your expo-
sure to asbestos:
• In 1973, EPA prohibited the
  spraying of asbestos-containing
  materials for insulation, fire pro-
  tection, and soundproofing.
• In 1975, EPA prohibited the use
  of asbestos for pipe covering if
  the material is easily crumbled
  after it dries.

• In 1977, CPSC banned two
  asbestos-containing products:
  batching compounds and artifi-
  cial fireplace emberizing mate-
  rials (ash and embers) contain-
  ing respirable asbestos.
The CPSC is investigating the risk
from asbestos in other products. In-
formation on other products will be
made available as investigations
are completed. This continuing re-
search activity should produce the
most effective program possible for
reducing unnecessary human ex-
posure to asbestos.
   If asbestos building materials must be removed from a home,
   this work must only be done by a qualified asbestos removal
   contractor. Many states now require asbestos contractors to
   be trained and certified. All repair of asbestos materials must
   be done with extreme caution.

-------
Thble of Contents
Questions Answered in this Booklet
What is asbestos?  	4
Is asbestos dangerous?	4
Are all products with asbestos a health risk for consumers?  .. 4
Do all people exposed to asbestos develop asbestos-related
disease? 	4
What hazards do cigarette smokers face when exposed to as-
bestos? Do they have a greater chance of developing lung
cancer than smokers not exposed to asbestos?	4
Where is asbestos used in the home? 	4
How can I tell if I have asbestos in my home? 	4
If I find asbestos in my home, what should I do?  	4
Vinyl Floor Tiles and Vinyl Sheet Flooring  	5
Patching Compounds and Textured Paints	6
Ceilings 	6
Stoves and Furnaces	7
Door Gaskets	7
Walls and Pipes	?	8
Appliances	9
Roofing, Shingles and Siding  	9
How to Identify Asbestos 	9
General Guidelines for Handling Products Containing
Asbestos	10-11
More Information	12

-------
Q*A
Q
A-
    . What is
    •  asbestos?
Q
• Are all products with
•  asbestos a health risk
      Asbestos is a mineral fiber    f°r the consumer?
      found in rocks. There are
several kinds of asbestos fibers, all
of which are fire resistant and not
easily destroyed or degraded by
natural processes.
Q:
A:
      Is asbestos
      dangerous?
      Asbestos has been shown to
   u  cause cancer of the lung and
stomach according to studies of
workers and others exposed to as-
bestos. There is no level of expo-
sure to asbestos fibers that experts
can assure is completely safe.
Some asbestos materials can break
into small fibers which can float in
the air, and these fibers can be in-
haled. You cannot see these tiny
fibers, and they are so small that
they pass through the filters of nor-
mal vacuum cleaners and get back
into the air.  Once inhaled, asbestos
fibers can become lodged in tissue
for a long time. After many years,
cancer or mesothelioma can
develop.
In order to be a health risk, as-
bestos fibers must be released
from the material and be present
in the air for people to breathe.
                                 A
     «p NO. A health risk exists only
      when asbestos fibers are re-
leased from the material or product.
Soft, easily crumbled asbestos-
containing material has the greatest
potential for asbestos release and
therefore has the greatest potential
to create health risks.

    Q. Do all people exposed
    • to asbestos develop
asbestos-related disease?
     At NO. Most people exposed to
      small amounts of asbestos
do not develop any related health
problems. Health studies of asbes-
tos workers and others, however,
show that the chances of develop-
ing some serious illnesses, includ-
ing lung cancer, are greater after
exposure to asbestos.

    Q. What hazards do
    1 cigarette smokers face
when exposed to asbestos?
Do they have a greater .
chance of developing lung
cancer than smokers not
exposed to asbestos?
     At YES. Asbestos exposure
      and cigarette smoking to-
gether have been shown to cause a
greater risk of lung cancer than
either the risk of cancer produced
by smoking or working with asbes-
tos alone.
                                 Q
                                    . Where is asbestos
                                    •  used in the home?
                                     A, Asbestos has been used in a
                                      wide variety of products, in-
                                 cluding household and building ma-
                                 terials, such as appliances, ceil-
                                 ings, wall and pipe coverings, floor
                                 tiles, and some roofing materials.
                                 Basically, asbestos has been used
                                 in products for four reasons: (1) to
strengthen the product material; (2)
for thermal insulation within a prod-
uct; (3) for thermal or acoustical in-
sulation or decoration on exposed
surfaces; and (4) for fire protection.
                                                                Q
                                • How can I tell if I have
                                '  asbestos in my home?
                                At The manufacturer of a prod-
                                  uct may be able to tell you.
                            based on the model number and
                            age of the product, whether or not
                            the product contains asbestos.
                            People who have frequently worked
                            with asbestos (such as plumbers.
                            building contractors, or heating con-
                            tractors) often are able to make a
                            reasonable judgment about
                            whether or not a material contains
                            asbetos based on a visual
                            inspection.
                                                                Q
                                  If I find asbestos in my
                                •  home, what should I
                                  do?
                                At In most cases, asbestos-
                                  containing materials are
                            best left alone. When it is neces-
                            sary to use or work with asbestos-
                            containing materials, reduce your
                            exposure to fibers as much as
                            possible. To help you do this, we
                            have provided some general
                            guidelines on pages 10-11 for work-
                            ing with  products containing asbes-
                            tos. If at all possible, get help from a
                            contractor who is trained and ex-
                            perienced in working with asbestos.
                            Be sure  the contractor is familiar
                            with and follows the guidelines on
                            pages 10-11 for handling as-
                            bestos-containing materials. In
                            general, home repair contractors
                            are not experienced in the proper
                            procedures for handling asbestos
4

-------
Vinyl Floor Tiles  and
Vinyl Sheet Flooring
                            Asbestos has been added to some
                            vinyl floor tiles to strengthen them.
                            Asbestos is also present in the
                            backing on some vinyl sheet floor-
                            ing. The asbestos is often bound in
                            the tiles and backing with vinyl or
                            some type of binder. Asbestos fi-
                            bers can be released if the tiles are
                            sanded or seriously damaged, or if
                            the backing on the sheet flooring is
                            dry-scraped or sanded, or if the tiles
                            are severely worn or cut to fit into
                            place.
                            When replacement or repair be-
                            comes necessary, follow the
                            guidelines given on pages 10-11.
                            The tiles should be handled as little
                            as possible. Avoid sanding or
                            otherwise damaging them. A safe
                            and recommended alternative is to
                            place a new flooring material di-
                            rectly over the old tiles or sheet.
For additional information, you may
wish to read: "Recommended Work
Procedures for Resilient Floor
Covers," available on request from
the Resilient Floor Covering Insti-
tute, 103015th St., NW, Suite 350.
Washington, DC 20005. Enclose a
business-size, self-addressed,
stamped envelope for that
publication.

-------
Patching Compounds
and Textured Paints
                                                   AY 5V
 In 1977, CPSC banned asbestos-
 containing patching compounds.
 Some wall and ceiling joints may be
 patched with asbestos-containing
 material manufactured before 1977.
 If the material is in good condition, it
 is best to leave it alone. Sanding
 and scraping will release asbestos
 fibers. If it is in poor condition, or if
 the wall or ceiling needs to be re-
 moved or repaired, follow the
 guidelines on pages 10-11.
Some textured paint sold before
1978 contained asbestos. It is un-
likely that asbestos is being added
to textured paint today, based on
information obtained from manufac-
turers by the CPSC. As with patch-
ing compounds, textured paint is
best left alone if undamaged. Sand-
ing or cutting a surface with tex-
tured paint that may contain asbes-
tos should be avoided.
Ceilings
Some large buildings and a few
homes built or remodeled between
1945 and 1978 may contain a
crumbly, asbestos-containing mate-
rial which has been either sprayed
or troweled onto the ceiling or walls.
If the material is in good condition, it
is best to leave it alone. If the mate-
rial appears damaged, you may
want to consider having it repaired
or removed.
If possible, contact the builder or
the contractor who applied the ceil-
ing coating to determine whether
asbestos-containing material was
used; This may be difficult to do in
older homes. If you decide that it is
necessary to remove this type of
asbestos material, follow the
guidelines on pages 10-11. The use
of a trained asbestos contractor is
highly advised when asbestos-
containing material is to be re-
moved.

-------
 Stoves  and Furnaces
 Stove Insulation
 Asbestos-containing cement
 sheets, millboard and paper have
 been used frequently in homes
 when wood-burning stoves have
 been installed. These asbestos-
 containing materials are used as
 thermal insulation to protect the
 floor and walls around the stoves.
 On cement sheets,  the label may
 tell you if it contains asbestos.
 The cement sheet material prob-
 ably will not release asbestos fibers
 unless scraped. This sheet material
 may be coated with a high tempera-
 ture paint, which will help seal any
 asbestos into the material.
 Asbestos paper or millboard are
 also used for this type of thermal
 insulation.  If these materials have
 been placed where  they are sub-
 jected to wear, there is an increased
 possibility that asbestos fibers may
 be released. Damage or misuse of
 the insulating material by sanding,
 drilling, or sawing will also release
 asbestos fibers. Suitable precau-
 tions should be taken (see guide-
 lines on pages 10-11).
Door
Gaskets
Some door gaskets in furnaces,
ovens, and wood and coal stoves
may contain asbestos. The
asbestos-containing door gaskets
on wood and coal-burning stoves
are subject to wear and can release
asbestos fibers under normal use
conditions. Handle the asbestos-
containing material as little as
possible, following the guidelines
on pages 10-11.
Furnace Insulation
Oil, coal, or wood furnaces with as-
bestos-containing insulation and
cement are generally found in some
older homes. Updating the system
to oil or gas can result in removal or
damage to the old insulation.

If the insulation on or around your
furnace is in good condition, it is
best to leave it alone. If the insula-
tion is in poor condition, or pieces
are  breaking off, you may want to
consider having it repaired or re-
moved.  First find out if the insula-
tion contains asbestos; if it does,
follow the guidelines on pages
10-11.

If the insulation is breaking off
around the furnace, children
should not play In this dusty
area.

-------
Walls  and Hpes
Pipe Insulation
Hot water and steam pipes in some
older homes may be covered with
an asbestos-containing material
primarily to reduce heat loss, and to
protect nearby surfaces from the
hot pipes. Pipes may also be wrap-
ped in an asbestos "blanket" or as-
bestos paper tape. Asbestos-
containing insulation has also been
used on furnace ducts. Most asbes-
tos pipe insulation in homes is pre-
formed to fit around various diame-
ter pipes. This type of asbestos-
containing insulation was manufac-
tured from 1920 to 1972.

If you have damaged insulation
around pipes or boilers, the best
current recommendation  is to leave
the insulation in place and repair
the protective covering. In many
circumstances, this is the best way
to minimize potential exposure to
asbestos. For example, small holes
in pipe covering may be filled with
caulking or spackling and then cov-
ered with rewettable glass cloth.


Wall and Ceiling Insulation

Homes constructed between 1930
and 1950 may contain insulation
made with asbestos. Wall and ceil-
ing insulation that contains asbes-
tos is generally found inside the
wall or ceiling ("sandwiched" be-
hind plaster walls). Renovation and
home improvements may expose
and disturb the materials. In cases
of major disruption of asbestos-
containing material, it is exceed-
ingly important that a trained asbes-
tos contractor be used. Find a con-
tractor (such as one familiar with
removal of asbestos ceilings in
schools) who is experienced with
guidelines for handling asbestos
and will follow the guidelines on
pages 10-11 to do this work.
e
8

-------
 Appliances
 Some appliances are, or have
 been, manufactured with
 asbestos-containing parts or com-
 ponents. The CPSC is making an
 effort to identify household
 appliances which could release as-
 bestos fibers during use. The
 CPSC has reviewed information on
 the use of asbestos-containing
 parts in toasters, popcorn poppers,
 broilers, slow cookers, dishwash-
 ers, refrigerators, ovens, ranges,
 clothes dryers and electric blan-
kets. There has been a general de-
cline in the use of asbestos in these
appliances during recent years.
When asbestos is used, it is in parts
which will probably not result in the
release of asbestos fibers during
use. It is unlikely that asbestos
components in these appliances
present a significant health risk
from release of asbestos fibers.
An exception was hair dryers with
asbestos-containing heat shields.
Manufacturers voluntarily recalled
such hair dryers in 1979. Labora-
tory tests of most hair dryers
showed that asbestos fibers were
released during use. Current pro-
duction hair dryer models do not
contain asbestos heat shields.
If you are concerned about asbes-
tos in an appliance, do not repair it
yourself. Instead, have a qualified
repair technician repair it.
Roofing,  Shingles,  and Siding
Some roofing shingles, siding shin-
gles and sheets have been manu-
factured with asbestos-using
Portland cement as a binding agent.
Since these products are already in
place and outdoors, there is likely to
be little risk to human health. How-
ever, if the siding is worn or dam-
aged, you may spray paint it to help
seal in the fibers.
You should avoid disturbing these
products if they are already part of
your home. Unless the roofing must
be replaced as a result of normal
wear, it is wiser to simply leave it in
place. If repair or replacement is
necessary, follow the guidelines on
pages 10-11.
now  to Identify Asbestos
You should first try to determine
whether the material does in fact
contain asbestos. Avoid disturbing
the material if at all possible. If you
cannot determine from the label, in-
staller, or manufacturer whether the
material contains asbestos, it is
best to assume that the product
does contain asbestos.
People who have frequently worked
with asbestos material (such as
plumbers, building contractors or
heating contractors) often are able
to make a reasonable judgment
about whether or not a product con-
tains asbestos, based on a visual
inspection. If you are uncertain
whether some materials contain
asbestos, you may want to call
such people for advice.
In some cases, you may want to
have the material analyzed. Such
analysis may be desirable if you
have a large area of damaged ma-
terial or if you are preparing a major
renovation which will expose mate-
rial contained behind a wall or other
barrier. Before attempting to sample
the material, call the CPSC Hotline
number on page 12 for information
on sampling and to locate a labora-
tory capable of analyzing material
samples for asbestos. Laboratory
analysis can be expensive, ranging
from about $20 to more than $40
per sample, and several samples
may be required to have a more
accurate determination of asbestos
content.
                                                                                       9

-------
 General Guidelines
 for Handling Products Containing Asbestos
 If you think that a material contains
 asbestos, and you have to disturb
 it, handle it very carefully. Special
 precautions should be taken during
 removal of exposed or damaged
 asbestos-containing material. If
 possible, find a contractor trained in
 safe procedures for handling asbes-
 tos (such as a contractor familiar
 with removal of asbestos ceilings in
 schools). Always keep the following
 caution in mind:
   Caution:
   Do not dust, sweep, or
   vacuum particles sus-
   pected of containing
   asbestos. This will dis-
   turb tiny asbestos fibers
   and may make them
   airborne. The fibers are
   so small that they can-
   not be seen and can
   pass through normal
   vacuum cleaner filters
   and get back into the
   air. The dust should be
   removed by a  wet-
   mopping procedure or
   by specially-designed
   "HEPA" vacuum  clean-
   ers used by trained
   asbestos contractors.
Follow these basic precautions for
working with asbestos:

1. Do not disturb any material you
  think may contain asbestos un-
  less you have to. Removal of the
  material is usually the last
  alternative.

2. Seal off the work area from the
  rest of the residence. Plastic
  sheeting and duct tape may be
  used. Take great care not to
  track asbestos dust into other
  areas of the residence.
3. Always wear a certified respira-
  tor appropriate for the specific
  asbestos activity. Wear gloves,
  hats, and other protective cloth-
  ing. If possible, dispose of all of
  this equipment immediately after
  using it. If you cannot dispose of
  your clothing, wash it separately
  from the family's wash. (Call the
  CPSC Hotline number listed on
10

-------
page 12 for information on
respirators.)

When working with asbestos-
containing material, wet it with a
hand sprayer. The sprayer
should provide a fine mist, and
the material should be thor-
oughly dampened, but not drip-
ping wet. Wet fibers do not float
in the air as readily as dry fibers
and will be easier to clean up.
The addition of a small amount
(about  a teaspoon to a quart of
water)  of a low-sudsing dish or
laundry detergent will improve
the penetration of the water into
the material and reduce the
amount of water needed.
5.  If you must drill or cut an
   asbestos-containing material,
   do the drilling or cutting outside if
   possible. Wet the material first
   ^according to instructions in item
   4, above).

6.  If you must remove the material,
   avo.id breaking it into small
   pieces. While it is easier to re-
   move and handle small pieces,
   you are more likely to release
   asbestos fibers if you break the
   material into small pieces. Pipe
   insulation was usually installed
   in preformed blocks; remove
   these in complete pieces.
7. Place any material you remove
   and any debris from the work in
   plastic trash bags and dispose
   of it in a proper land-fill. Call your
   health department for instruc-
   tions about how to dispose oT
   this. Take care not to break the
   bag.
8. After you finish removing the
   material, thoroughly clean the
   area with wet mops, wet rags, or
   sponges. Repeat the cleaning
   procedure a second time. Wet-
   ting will help to reduce the
   chance that the fibers get spread
   around. Again, see that no as-
   bestos material is tracked into
   other areas. If possible,  dispose
   of the mop heads, rags, and
   sponges in the trash bags with
   the removed materials. Other-
   wise, vigorously flush the mop,
   rag, or sponge in running water
   in a sink or basin with a drain.
   Make sure to completely rinse
   both the utensil and the  basin.
9. If you are going to have work
   done by a contractor, discuss
   these guidelines and other steps
   to minimize asbestos exposure.
                                                                                                11

-------
                                 More Information
                                 For information about laboratories for asbestos testing, advice about
                                 where to get respirators, and guidelines for how to repair or remove
                                 asbestos, call the CPSC Hotline (numbers below) or write to the U.S.
                                 Consumer Product Safety Commission, Washington, DC 20207. The
                                 CPSC Hotline also has information on certain appliances and products
                                 (such as the brands and models of hairdryers that contained asbestos).
                                                                                        3.7-7 -**
                                 Call CPSC at	800-638-CPSC

                                 A teletypewriter (TTY) for the deaf is available on the following numbers:
                                 National TTY (including Alaska and Hawaii)—800-638-8270.
                                 Maryland TTY only—800-492-8104.
                                 The U.S. Consumer Product Safety Com-
                                 mission (CPSC) is an independent regu-
                                 latory agency charged with reducing unrea-
                                 sonable risks of injury associated with con-
                                 sumer products. CPSC is headed by five
                                 Commissioners appointed by the President
                                 with the advice and consent of the Senate.
12
This document is in the public domain. It
may be reproduced in part or in whole by an
individual or organization without permis-
sion. If it is reproduced, however, the Com-
mission would appreciate knowing how it «
used. Write to the U.S. Consumer Product
Safety Commission, Office of Information
and Public Affairs, Washington, DC 20207.

For sale by the Superintendent of Doc-
uments, U.S. Government Printing Office

a uj. Qovsiuniiirrnumyooma.  ise? - ui-ut - nwuaot

-------