United States Office of Water EPA 821-R-01-029
Environmental Protection Washington, D.C. 20460 April 2001
Agency
&EPA Method 1602: Male-specific (F+) and
Somatic Coliphage in Water by Single
Agar Layer (SAL) Procedure
April 2001
-------
Acknowledgments
This method was prepared under the direction of William A. Telliard of the Engineering and Analysis
Division within the U.S. Environmental Protection Agency's (EPA) Office of Water. The EPA technical
lead was Paul Berger, of the Standards and Risk Management Division within the Office of Water. This
document was prepared under EPA Contract No. 68-C-98-139 by DynCorp Information & Enterprise
Technology, Inc.
The contributions of the following persons and organizations to the development of this method are
gratefully acknowledged:
Sobsey, Mark, Ming Jing Wu, and Greg Lovelace, University of North Carolina, Department of
Environmental Sciences and Engineering, CB#7400, McGavran-Greenberg Building, Chapel Hill,
NC 27599
Hsu, Fu-Chih, and Jim Larkin, Environmental Health Laboratories, 110 South Hill Street, South Bend, IN
46617
Chambers, Yildiz, City of San Diego Marine Microbiology Laboratory, 5530 Kiowa Drive, La Mesa, CA
91942
Cliver, Dean, Tadesse Mariam, and Mulugeta Tamene, University of California Davis, Department of
Health and Reproduction, School of Veterinary Medicine, Davis, CA 95616-8743
Danielson, Richard, BioVir Laboratory, 685 Stone Road Unit # 6, Benicia, CA 94510
Fujioka, Roger and Geeta Rijal, University of Hawaii, Water Resources Center, Holmes Hall 283, 2540
Dole Street, Honolulu, HI 96822
Karim, Mohammad and Dale Young, American Water Works System Research Laboratory, 1115 South
Illinois Street, Belleville, IL 62220-3731
Margolin, Aaron and Nicola Ballester, University of New Hampshire, Department of Microbiology,
Biological Sciences Building, Rudman Hall Room 285, Durham, NH 03824
Pillai, Suresh and Elisa Camacho, Texas A & M University, Department of Poultry Science, Kleberg
Center Room 418D, College Station, TX 77843
Pope, Misty, Kevin Cornell, Jason Kempton, Ken Miller, and Jessica Pulz, DynCorp Information and
Enterprise Technologies, 6101 Stevenson Avenue, Alexandria, VA 22304
Williams, Fred and Ron Stetler U.S. Environmental Protection Agency, 26 West Martin Luther King
Drive, Cincinnati, OH, 45268
Yates, Marylynn, Omid Bakhtar, and Andre Salazar, University of California Riverside, Department of
Environmental Sciences, 2217 Geology, Riverside, CA 92521-0424
-------
Disclaimer
Mention of trade names or commercial products does not constitute endorsement or recommendation for
use.
-------
-------
Introduction
Coliphage presence in ground water is an indication of fecal contamination. Method 1602 is a performance-
based method for enumerating male-specific (F+) and somatic coliphage in ground water and other waters.
Laboratories are permitted to modify or omit any steps or procedure, with the exception of the coliphage
stock enumeration procedure (Section 11.3), provided that all performance requirements set forth in the
validated method are met. The laboratory may not omit any quality control analyses.
This single agar layer procedure requires the addition of host bacteria, magnesium chloride, and double-
strength molten agar medium to the sample, followed by pouring the total volume of the mixture into plates.
All plates from a single sample are examined for plaque formation (zones of bacterial host lawn clearing).
The quantity of coliphage in a sample is expressed as plaque forming units (PFU) / 100 mL.
This method is for use in the Environmental Protection Agency's (EPA's) data gathering and monitoring
programs under the Safe Drinking Water Act and the Clean Water Act.
Questions concerning this method or its application should be addressed to:
William A. Telliard
U.S. EPA Office of Water
Analytical Methods Staff
1200 Pennsylvania NW
Mail Code 4303
Washington, DC 20460
Email: telliard.william@epa.gov
Requests for additional copies of this publication should be directed to:
Water Resource Center
Mail Code RC-4100
401 M Street, SW
Washington, D.C. 20460
(202) 260-7786 or (202) 260-2814
IV
-------
-------
Table of Contents
1.0 Scope and Application 1
2.0 Summary of Method 1
3.0 Definitions 1
4.0 Interferences 2
5.0 Safety 2
6.0 Equipment and Supplies 3
7.0 Reagents and Standards 4
8.0 Sample Collection, Preservation, and Storage 9
9.0 Quality Control 10
10.0 Calibration and Standardization 15
11.0 Enumeration of Coliphage QC Spiking Suspensions 15
12.0 Single Agar Layer (SAL) Procedure for Sample Analysis 18
13.0 Data Analysis and Calculations 20
14.0 Method Performance 22
15.0 Pollution Prevention 23
16.0 Waste Management 23
17.0 References 24
18.0 Flowcharts 25
19.0 Glossary 29
VI
-------
-------
Method 1602: Male-specific (F+) and Somatic Coliphage in
Water by Single Agar Layer (SAL) Procedure
April 2001
1.0 Scope and Application
1.1 The single agar layer (SAL) procedure detects and enumerates male-specific (F+) and somatic
coliphages in ground water and other waters. This method is intended to help determine if ground
water is affected by fecal contamination.
1.2 Although this method may be used for water matrices other than ground water, it has only been
validated for use in ground water.
1.3 This method is based on procedures developed for the determination of coliphage in water in the
Supplement to the 20th Edition of Standard Methods for the Examination of Water and
Wastewater (Reference 17.1).
1.4 This method is not intended for use in biosolids samples or as a test for microorganisms other than
coliphage. This method may be used in ground water and other water matrices where coliphage is
suspected to be present.
1.5 Each laboratory and analyst that uses this method must first demonstrate the ability to generate
acceptable results using the procedures in Section 9.0.
1.6 Any modification of the method beyond those expressly permitted is subject to the application and
approval of alternate test procedures under 40 CFR parts 136.4 and 136.5, and/or 141.27.
2.0 Summary of Method
2.1 Method 1602 describes the single agar layer (SAL) procedure. A 100-mL ground water sample is
assayed by adding MgCl2 (magnesium chloride), log-phase host bacteria (E. coll Famp for F+
coliphage and E. coll CN-13 for somatic coliphage), and 100 mL of double-strength molten tryptic
soy agar to the sample. The sample is thoroughly mixed and the total volume is poured into 5 to 10
plates (dependent on plate size). After an overnight incubation, circular lysis zones (plaques) are
counted and summed for all plates from a single sample. The quantity of coliphage in a sample is
expressed as plaque forming units (PFU) / 100 mL. For quality control purposes, both a coliphage-
positive reagent water sample (OPR) and a negative reagent water sample (method blank) are
analyzed for each type of coliphage with each sample batch.
3.0 Definitions
3.1 Coliphages are viruses (bacteriophages) that infect E. coll and are indicators of fecal
contamination. This method is capable of detecting two types of coliphages: male-specific (F+) and
somatic.
3.2 F-factor is the fertility factor in certain strains of E. coll. It is a plasmid that, when present, codes
for pilus formation. The pilus allows for transfer of nucleic acid from one bacterium to another.
1 April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
3.3 Male-specific coliphages (F+) are RNA or DNA viruses that infect via the F-pilus of male strains
of E. coli.
3.4 Somatic coliphages are DNA viruses that infect host cells via the outer cell membrane.
3.5 Definitions for other terms used in this method are given in the glossary in Section 19.3.
4.0 Interferences
4.1 During the single agar layer procedure the sample and host bacteria should not remain in contact
with each other for more than 10 minutes prior to plating and after plating the agar must harden
within 10 minutes. Increased contact time or agar hardening time may result in replication of
phages such that the initial phage concentration is overestimated. The entire plating procedure from
combining sample with host to hardening of single-agar layer plates should not exceed 20 minutes.
5.0 Safety
5.1 The biohazards and the risk of infection by pathogens associated with handling raw sewage are
high in this method. Use good laboratory practices when working with potentially harmful samples.
5.2 Method 1602 does not purport to address all of the safety problems associated with its use. It is the
responsibility of the laboratory to establish appropriate safety and health practices prior to use of
this method. The analyst/technician must know and observe the safety procedures required in a
laboratory that handles biohazardous material while preparing, using, and disposing of cultures,
reagents, and materials. The analyst/technician must use proper safety procedures while operating
sterilization equipment. Equipment and supplies that have come into contact with biohazardous
material or are suspected of containing biohazardous material must be sterilized prior to disposal
or re-use. Field and laboratory staff collecting and analyzing environmental samples are under
some risk of exposure to pathogenic microorganisms. Staff should apply safety procedures used for
handling pathogens to all samples.
5.3 The laboratory is responsible for maintaining a current awareness file of Occupational Safety and
Health Administration (OSHA) regulations regarding the safe handling of the chemicals specified
in this method. A reference file of material safety data sheets should be made available to all
personnel involved in these analyses. Additional information on laboratory safety can be found in
Section 16.0 Waste Management.
5.4 Samples may contain high concentrations of biohazardous agents and must be handled with gloves.
Any positive reference materials also must be handled with gloves in an appropriate laboratory
hood. The analyst/technician must never place gloves near the face after exposure to media known
or suspected to contain pathogenic microorganisms. Laboratory personnel must change gloves after
handling raw sewage or any other items which may carry pathogenic microorganisms.
5.5 Mouth pipetting is prohibited.
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
6.0 Equipment and Supplies
Please note: Brand names, suppliers, and part numbers are for illustrative purposes only. No
endorsement is implied. Equivalent performance may be achieved using apparatus and materials other
than those specified in this section, but demonstration of equivalent performance that meets the
requirements of this method is the responsibility of the laboratory.
6.1 Equipment for collection and transport of samples
6.1.1 Bottles for collection of water—Sterile, wide-mouth, polypropylene, 4-L (or smaller)
bottles or carboys with screw caps
6.1.2 Ice chest—Igloo, Coleman, styrofoam box or equivalent
6.1.3 Ice
6.1.3.1 Wet ice—purchased locally, or
6.1.3.2 Ice packs—Blue Ice, UTek cat. no. 429, or equivalent, frozen for use
6.1.4 Bubble wrap
6.2 Equipment and supplies for growth of microorganisms
6.2.1 Sterile dilution tubes with screw caps—Reusable or disposable, 16 x 150 mm, or
16 x 100mm
6.2.2 Test tube rack—Size to accommodate tubes specified in Section 6.2.1
6.2.3 Glass or plastic, plugged, sterile serological pipettes—To deliver, of appropriate
volume(s) (Falcon, Kimble, or equivalent)
6.2.4 Pipet bulbs, automatic pipetter—Pipet-Aid or equivalent
6.2.5 Inoculation loops—Nichrome or platinum wire, disposable, sterile plastic loops, or wooden
applicator, at least 3 mm in diameter or 10 \\L volume (VWR, Fisher, DIFCO, or
equivalent)
6.2.6 Micropipettors, adjustable—10- to 200-(iL, and 100- to 1000-(iL, with appropriate
aerosol resistant tips, Gilson, Eppendorf, or equivalent. Please note: To avoid cross-
contamination, micropipettors should be wiped down with a 1 : 100 solution of
household bleach follow ed by a 10% solution of sodium thiosulfate. Alternatively,
disposable pipets (Serological, Pasteur, or equivalent) may be used.
6.2.7 Burner—Alcohol, Bunsen, Fisher, or equivalent
6.2.8 Sterile disposable petri dishes—100-mm -diameter dishes (Falcon # 1029) or
150-mm-dishes (Falcon #1058) or equivalent
6.2.9 Incubator capable of maintaining 36°C ± 1.0 °C for growth of microorganisms
6.2.10 Beakers—2- and 4-L, sterile, polypropylene, glass, or polycarbonate
6.2.11 Polypropylene, glass, or polycarbonate bottles—Wide-mouth, 100-mL or 1-L, square or
round, autoclavable with screw cap
6.2.12 Erlenmeyer flasks—1-L and 2-L, sterile, Corning, Nalgene, Kimble or equivalent
6.2.13 Stir bar—Fisher cat. no. 14-511-93, or equivalent
6.2.14 Stir plate—Fishercat.no. 14-493-120S, or equivalent
6.2.15 Water bath capable of maintaining 36°C ± 1.0°C and 45°C to 48°C —Precision, VWR
Scientific, or equivalent
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
6.2.16 Sterilization filtration equipment—Millex type for syringe or larger Millipore type, sterile,
0.22-(jm pore size
6.2.17 Sterile, cotton-tipped applicators
6.2.18 Latex gloves for handling samples, supplies, and equipment—Microflex, San Francisco,
CA, stock no. UL-315-L, or equivalent
6.2.19 pH meter—Beckman, Corning, or equivalent
6.2.20 Vortex mixer—Vortex Genie, or equivalent
6.2.21 Spectrophotometer or colorimeter (with wavelengths in visible range)—Spectronic 20,
Spectrum Instruments, Inc., or equivalent, with cell holder for V" diameter cuvettes
(Model # 4015) or 13 mm x 100 mm cuvettes
6.2.22 Cuvettes—1-cm light path, Beckman, Bausch and Lomb, or equivalent
6.2.23 Shaker flasks—Fluted Erlenmeyer,125-mL with slip cap or sterile plug, Fisher
(09-552-33, 10-140-6, 10-041-5A) or equivalent or equivalent
6.2.24 Shaker incubator—Capable of 36°C ± 1.0 °C and 100 to 150 rpm, New Brunswick,
PsychoTherm, Innova, or equivalent or an ordinary shaker in an incubator
6.2.25 Flask weights—VWR 29700-004 or equivalent
6.3 Supplies for collection and filtration of raw sewage (Section 7.4.3)
6.3.1 Disposable filter disks—25-mm-diameter, 0.45-(jm pore size, sterile, low protein binding
(Gelman Acrodisc HT Tuffryn, No. 4184, cellulose acetate Corning No. 21053-25, or
equivalent)
6.3.2 Syringes—Sterile, disposable, 5-,10-, or 20-mL
6.3.3 Polypropylene dilution tubes—Sterile, 10- to 20-mL, Falcon or equivalent
6.3.4 Sterile glass or polypropylene 250-mL bottles for collection of raw sewage
6.4 Miscellaneous lab ware and supplies
6.4.1 Lint-free tissues—KimWipes or equivalent
6.4.2 Weigh boats
6.4.3 Graduated cylinders—Sterile, polypropylene or glass, 100-mL, 250-mL, and 1-L
6.4.4 Autoclave
6.4.5 Thermometers—Range of 0°C to 100°C
6.4.6 Balance—Capable of weighing to 0.1 mg for samples having a mass up to 200 g
6.4.7 Freezer vials—Sterile, 5-mL screw cap, Nunc or equivalent
6.4.8 Light box—VWR 21475-460 or equivalent
7.0 Reagents and Standards
7.1 General reagents
7.1.1 Reagent water—Should conform to Specification D 1193, Annual Book of ASTM
Standards (Reference 17.5).
7.1.2 10% (w/v) Sodium thiosulfate—Add 10 g sodium thiosulfate (Na2S2O3) per 90 mL reagent
water. Mix until dissolved. Bring to a final volume of 100 mL and autoclave for 15
minutes at 121°C and 15 psi.
April 2001 4
-------
Method 1602: Single Agar Layer (SAL) Procedure
7.1.3 Stock magnesium chloride (SOX, 4M)—To 814 g of MgCl2'6H2O, add 300 mL reagent
grade water. Stir to dissolve. Bring to a final volume of 1 L, and mix thoroughly.
Autoclave for 15 minutes at 121°C and 15 psi.
7.1.4 Glycerol—Sigma #G6279 or equivalent. Autoclave for 15 minutes at 121°C and 15 psi.
Remove promptly to avoid scorching. Store at room temperature.
7.1.5 Household bleach
7.1.6 Ethanol—70% or greater
7.2 Antibiotic stocks—Antibiotics must always be added to medium after the medium has been
autoclaved.
7.2.1 Stock nalidixic acid (Sigma N4382, or equivalent)—Please note: Nalidixic acid is
considered toxic. Wear suitable protective clothing, gloves, and eye/face protection and
use in a chemical fume hood.
7.2.1.1 For growth of E. coli CN-13, the host bacteria for somatic coliphage.
7.2.1.2 Dissolve 1 g of nalidixic acid sodium salt in 100 mL reagent water. Filter
through a sterile, 0.22-(jm-pore-size membrane filter assembly. Dispense 5 mL
per 5-mL freezer vial, date vial, and store frozen at -20°C for up to one year.
Thaw at room temperature or rapidly in a 36°C ± 1.0°C water bath. Mix well
prior to use.
7.2.2 Stock ampicillin/streptomycin
7.2.2.1 For growth of E. coli Famp, the host bacteria for male-specific coliphage.
7.2.2.2 Dissolve 0.15 g of ampicillin sodium salt (Sigma A9518) and 0.15 g
streptomycin sulfate (Sigma S6501) in 100 mL of reagent water. Filter through
a sterile 0.22-(jm-pore-size membrane filter assembly. Dispense 5 mL per
5-mL freezer vial, date vial, and store frozen at -20°C for up to one year. Thaw
prior to use at room temperature or rapidly in a 36°C ± 1.0°C water bath. Mix
well prior to use.
7.3 Media
7.3.1 Tryptic (or trypticase) soy broth (TSB)—(DIFCO 0370-15-5, or equivalent)
7.3.1.1 TSB—Follow procedure as specified on bottle of media. If dehydrated medium
is not available, prepare the media by adding 17.0 g of tryptone, 3.0 g of
soytone, 2.5 g of dextrose, 5.0 g of sodium chloride, and 2.5 g of dipotassium
phosphate to 1L of reagent water and heat to dissolve. Adjust pH to 7.3 with
1.0 N hydrochloric acid or 1.0 N sodium hydroxide, if necessary. Autoclave at
121°C and 15 psi for 15 minutes. Check pH again after autoclaving by
aseptically removing an aliquot of medium. Adjust pH as necessary. Discard
aliquot after checking pH, to ensure that the medium is not contaminated.
7.3.1.2 TSB with nalidixic acid (for growth of E. coli CN-13)—Aseptically add 10 mL
of stock nalidixic acid (Section 7.2.1) to 1 L of autoclaved, cooled
(48°C ± 1.0°C) TSB (Section 7.3.1.1) and mix. Please note: Antibiotics must
always be added to medium after the medium has been autoclaved and cooled.
7.3.1.3 TSB with streptomycin/ampicillin (for growth of E. coli F^p )—Aseptically add
10 mL of stock streptomycin/ampicillin sulfate (Section 7.2.2) to 1 L of
autoclaved, cooled (48°C ± 1.0°C) TSB (Section 7.3.1.1) and mix. Please note:
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
Antibiotics must always be added to medium after the medium has been
autoclaved and cooled.
7.3.2 1.5% tryptic soy agar (TSA)—To be used in streak plates (Section 7.5.2.1) and as
bottom layer of agar (Section 11.3.1.3) during the double agar layer (DAL) coliphage
stock QC sample spiking suspension enumeration procedure. Prior to autoclaving the TSB
without antibiotics, prepared as described in Section 7.3.1.1, add 15 g of agar per liter of
TSB. While stirring, heat to dissolve agar. Autoclave for 15 minutes at 121°C and 15 psi.
Cool to 48°C ± 1.0°C and mix molten medium well to ensure even distribution.
7.3.2.1 For growth of somatic coliphages using E. coll CN-13 as host bacteria,
aseptically add 10 mL of stock nalidixic acid (Section 7.2.1) per liter of
autoclaved 1.5% TSA (Section 7.3.2). Please note: Antibiotics must always be
added to medium after the medium has been autoclaved and cooled. Swirl
flask until well mixed and aseptically dispense 17-18 mL per 100-mm plate.
Allow to solidify with lids off in a biohazard hood for several minutes prior to
use. If not used immediately, replace lids and store inverted at 4°C ± 1°C for up
to 2 weeks.
7.3.2.2 For growth of male-specific (F+) coliphages using E. coli Famp as host bacteria,
aseptically add 10 mL stock ampicillin/streptomycin sulfate (Section 7.2.2) per
liter of autoclaved 1.5% TSA (Section 7.3.2). Please note: Antibiotics must
always be added to medium after the medium has been autoclaved and cooled.
Swirl flask until well mixed and aseptically dispense 17-18 mL per 100-mm
plate. Allow to solidify with lids off in a biohazard hood for several minutes
prior to use. If not used immediately, replace lids and store inverted at
4°C ± 1°C for up to 2 weeks.
7.3.3 0.7% tryptic soy agar (TSA)—"Soft" agar for use as the top layer of agar (Section
11.3.1.1) during the double agar layer (DAL) coliphage stock QC sample spiking
suspension enumeration procedure. Prior to autoclaving the TSB without antibiotics,
prepared as described in Section 7.3.1.1, add 7 g of agar per liter of TSB. While stirring,
heat to dissolve agar. Autoclave for 15 minutes at 121°C and 15 psi. Cool to
48°C± 1.0°C.
7.3.3.1 0.7% TSA top agar tubes with nalidixic acid (for growth of E. coli CN-
13)—To 1 L of autoclaved 0.7% TSA (soft agar) (Section 7.3.3), aseptically
add 10 mL of stock nalidixic acid (Section 7.2.1). Please note: Antibiotics must
always be added to medium after the medium has been autoclaved and cooled.
Dispense 5 mL per sterile 10-mL tube, label, and keep at 45°C to 48°C until
use. Tubes must be used the day they are prepared.
7.3.3.2 0.7% TSA top agar tubes with ampicillin/streptomycin (for growth of
E. coli Famp)—To 1 L of autoclaved 0.7% TSA (soft agar) (Section 7.3.3),
aseptically add 10 mL of stock ampicillin/streptomycin (Section 7.2.2). Please
note: Antibiotics must always be added to medium after the medium has been
autoclaved and cooled. Dispense 5 mL per sterile 10-mL tube, label, and keep
at 45°C to 48°C until use. Tubes must be used the day they are prepared.
7.3.4 Single agar layer
7.3.4.1 Double-strength tryptic soy agar (2X TSA)—Double all components of TSB
without antibiotics from Section 7.3.1.1 (except reagent water) and add 18 g of
agar per liter. Heat to dissolve while stirring. Autoclave for 15 minutes at
121°C and 15 psi. Cool to 48°C± 1.0 °C. After autoclaving, swirl to mix.
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
Medium may become darker after autoclaving but this should not impact media
performance.
7.3.4.2 2X TSA with nalidixic acid (for growth of E. coli CN-13)—To 1 L of
autoclaved 2X TSA, aseptically add 20 mL of stock nalidixic acid (Section
7.2.1) and mix well. Please note: Antibiotics must always be added to medium
after the medium has been autoclaved and cooled. Keep molten at
45°C to 48°C in water bath until use. Agar must be used on the day of
preparation.
7.3.4.3 2X TSA with ampicillin/streptomycin (for growth of E. coli Famp)—To 1 L of
autoclaved 2X TSA, aseptically add 20 mL of stock ampicillin/streptomycin
(Section 7.2.2) and mix well. Please note: Antibiotics must always be added to
medium after the medium has been autoclaved and cooled. Keep molten at
45°C to 48°C in water bath until use. Agar must be used on the day of
preparation.
7.3.5 Spot plates—To be used during the plaque confirmation procedure (Section 12.6). Please
note: Condensation may accumulate at the edges of stored spot plates and may drip over
agar surface if tilted, ruining the spot pattern. If the stored spot plates have
condensation, incubate plates for approximately 10 minutes to eliminate condensation
prior to inoculation.
7.3.5.1 Log-phase host bacteria must be prepared in advance (Section 7.5.4). Dissolve
3 g TSB (Section 7.3.1.1) and 0.75 g bacteriological grade agar per 100 mL of
reagent grade water. Heat and mix to dissolve. Autoclave for 15 minutes at
121°C and 15 psi. Cool to 45°C to 48°C in a water bath.
7.3.5.2 Add 2 mL of log-phase host bacterium prepared as directed in Section 7.5.4 and
1 mL stock antibiotic (Section 7.2). Please note: Antibiotics must always be
added to medium after the medium has been autoclaved and cooled. Nalidixic
acid is used with E. coli CN-13, and ampicillin/streptomycin is used with
E. coli Famp. Swirl to mix, and pour 20 mL per 100-mm diameter, sterile petri
plate. Allow to solidify. Label plates with name of host bacterium. Plates may
be used that day or stored at 4°C ± 1°C for up to four days before use. Divide
the bottom of the plate into a grid of 1-cm squares using a permanent marking
pen. Number each square for ease of reference. Other alternatives include: 1)
gridded petri dishes, 2) adhesive grids, or 3) creating the 1-cm grid on a circular
plastic dish and attaching to the bottom exterior of the plate with cellophane
tape.
7.4 Coliphage stock
7.4.1 MS2 stock coliphage (ATCC#15597-B1)—Male-specific (F+) coliphage. Refer to
http://www.atcc.org/SearchCatalogs/faqBacteriology.cfnrfqlO for initial preparation of coliphage
stock. May be stored at 2°C to 8°C for up to 5 years.
7.4.2 phi-X 174 stock coliphage (ATCC#13706-B 1)—Somatic coliphage. Refer to
http://www.atcc.org/SearchCatalogs/faqBacteriologv.cfnrfqlO for initial preparation of coliphage
stock. May be stored at 2°C to 8°C for up to 5 years.
7.4.3 Coliphage stock from sewage filtrate—This filtrate will be used as a spiking suspension
for QC samples.
7.4.3.1 Collect approximately 100 mL of raw sewage in a 250-mL collection bottle.
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
7.4.3.2 Transport to the laboratory on ice. Analysis of raw sewage filtrate should begin
within 24 hours of collection.
7.4.3.3 Allow the raw sewage to settle at 4°C ± 1°C for 1 to 3 hours. This will make the
filtration process easier.
7.4.3.4 Remove a sterile, 20-mL syringe from its package, aseptically remove plunger
from barrel, and attach a filter disk to the syringe barrel.
7.4.3.5 Pipet 10 to 15 mL of supernatant from settled sewage into the syringe barrel.
7.4.3.6 Hold the assembly over a sterile 15-mL polypropylene tube with screw-cap or
snap-cap, insert the plunger into the syringe barrel, and push the sewage through
the filter into the sterile tube. If filter clogs, change it as necessary and continue
to filter sewage until at least 10 mL of filtered sewage is obtained in the 15-mL
polypropylene tube (filtration may require use of numerous filters).
7.4.3.7 Cap the tube, label with source, date, and initials, and store the filtrate at
4°C ± 1°C until ready to assay. If filtrate is stored more than 24 hours, it must
be re-titered before use.
7.5 Host bacteria stock cultures
7.5.1 Pure host bacteria cultures
7.5.1.1 E. coll CN-13 (somatic coliphage host)—Nalidixic acid-resistant mutant of
E. coli C; originated by Pierre Payment, Institute Armand Frappier, University
of Quebec, Montreal, Canada, frozen stock. ATCC#700609.
7.5.1.2 E. coli Famp— E. coli HS(pFamp)R (male-specific coliphage host)—originated
by Victor Cabelli, formerly of the Department of Microbiology, University of
Rhode Island, Kingston, RI, USA, frozen stock. ATCC#700891.
7.5.2 Frozen host bacteria stock cultures—The laboratory shall obtain reference host bacterial
cultures (Sections 7.5.1.1 and 7.5.1.2) and use these to establish pure frozen host stock
cultures that are maintained by the laboratory. Frozen stocks are used as inoculum for
overnight host bacteria stock cultures (Section 7.5.3).
7.5.2.1 Establish pure frozen stock cultures by streaking host bacteria onto 1.5% TSA
plates with appropriate antibiotic (Section 7.3.2) to attain isolated colonies.
7.5.2.2 Incubate inoculated plates overnight, pick an individual colony and inoculate
into tryptic soy broth with appropriate antibiotics (Sections 7.3.1.2 and 7.3.1.3),
and grow to log phase (Section 7.5.4).
7.5.2.3 Harvest broth by mixing sterile glycerol and broth with log-phase host bacteria
in a ratio of 1:4 in a 5-mL freezer vial. Prepare log-phase host bacteria as
described in Section 7.5.4, below. (Example: 200 \\L sterile glycerol plus
800 (A log-phase E. coli).
7.5.2.4 Label with E. coli strain and date of harvest.
7.5.2.5 Freeze host bacteria stock cultures at -70°C, if possible. Cultures can be frozen
at -20°C if the laboratory does not have the capability to freeze samples at
-70°C).
7.5.2.6 Host bacteria stored at -70°C may be retained for up to one year. If stored at
-20°C, the host bacteria may be retained for up to two months.
7.5.3 Overnight host bacteria stock cultures—Inoculum from an overnight bacterial host
culture will reach log-phase more rapidly than inoculum from frozen stock.
April 2001 8
-------
Method 1602: Single Agar Layer (SAL) Procedure
7.5.3.1 Dispense 25 mL of tryptic soy broth (TSB) with nalidixic acid (Section 7.3.1.2)
into a sterile 125-mL shaker flask. For proper growth conditions, each flask
should always contain 25 to 30 mL of medium.
7.5.3.2 Inoculate the flask with a loopful of E. coll CN-13 from the frozen stock culture
(Section 7.5.2).
7.5.3.3 Repeat Sections 7.5.3.1 and 7.5.3.2 using TSB with streptomycin/ampicillin as
the medium (Section 7.3.1.3) and E. coll Famp as the bacterial host.
7.5.3.4 Place a sterile slip cap or plug on the shaker flasks, label flasks, and secure in
shaker.
7.5.3.5 Incubate at 36°C ± 1.0°C and set shaker to 100 to 150 rpm overnight (18 to 20
hours).
7.5.3.6 Chill on wet ice or at 4°C ± 1°C until ready for use.
7.5.4 Log-phase host bacteria stock cultures (Section 18, Flow chart 1)
7.5.4.1 To a 125-mL shaker flask containing 25 mL of TSB with nalidixic acid (Section
7.3.1.2) add 0.1 to 1.0 mL of overnight E. coll CN-13 host bacteria stock
culture (Section 7.5.3 or 7.5.4.7). For proper growth conditions, each culture
flask of host bacteria should contain 25 to 30 mL of medium. As a result,
several flasks of host bacteria may have to be prepared (this depends on the
number of samples and controls being run each day). Each 100-mL sample
analyzed using the single agar layer procedure (Section 12) will require a
10-mL inoculum of log-phase host bacteria.
7.5.4.2 Repeat Section 7.5.4.1 using TSB with streptomycin/ampicillin (Section
7.3.1.3) as the medium and E. coll Famp as the bacterial host.
7.5.4.3 After inoculation, place a sterile slip-cap or plug on the shaker flasks and secure
in shaker incubator.
7.5.4.4 Incubate at 36°C ± 1.0°C and 100 to 150 rpm for approximately 4 hours or
until cultures are visibly turbid (cloudy), indicating log-phase growth.
7.5.4.5 Aseptically remove 1 mL of culture from flask, dispense into a cuvette (Section
6.2.22), and read absorbance at 520 nm. An absorbance reading between 0.1
and 0.5 optical density (OD) units is an indication of log-phase growth. If
proper OD has not been reached, place cultures back into shaker incubator and
take readings every 30 minutes until an OD of between 0.1 and 0.5 is reached.
7.5.4.6 Chill on wet ice or at 4°C ± 1°C to slow replication until ready for use. The
suspension may be stored up to 48 hours. However, the best results occur when
cultures are used immediately (within 6 hours).
7.5.4.7 Store remaining bacterial host culture at 4°C ± 1°C overnight to inoculate
flasks for the preparation of new log-phase bacterial hosts.
8.0 Sample Collection, Preservation, and Storage
Please note: Unless the sample is known or suspected to contain infectious agents (e.g., during an
outbreak), samples should be shipped as noninfectious and should not be marked as infectious. U.S.
Department of Transportation (DOT) regulations (49 CFR 172) prohibit interstate shipment of more
than 4 L of solution known to contain infectious materials. State regulations may contain similar
regulations for intrastate commerce. If an outbreak is suspected, ship less than 4 Lat a time.
9 April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
8.1 Samples are collected in plastic bottles or carboys and shipped to the laboratory for analysis.
Samples must be shipped at 2°C to 8°C using wet ice, Blue Ice®, or similar products to maintain
temperature. Samples must be stored at 4°C ± 1°C. Do not freeze.
8.2 Sample collection: Collect 250 mL of sample for each of the two coliphage types to allow for
sample re-analysis, if necessary.
8.3 The sampling team must maintain a log book with the following information for each sample:
8.3.1 Facility name and location
8.3.2 Date and time of collection
8.3.3 Name of analytical facility, contact, and phone number
8.3.4 Sample number
8.3.5 Sample location
8.4 The sample container must indicate the following:
8.4.1 Sample number
8.4.2 Date and time of collection
8.4.3 Sample collection location
8.5 Holding times. The following are maximum holding times beyond which the sample cannot be
retained for testing.
8.5.1 Single agar layer procedure—Between collection of sample and beginning of analysis: 48
hours
8.5.2 Raw sewage sample—Between collection of sewage sample and analysis: 24 hours, unless
re-titered and titer has not decreased by more than 50%. If titer has not decreased by more
than 50%, the sample can be stored for up to 72 hours.
8.6 Dechlorination procedure—Although this method was validated for use with unchlorinated ground
water, it potentially can be used with chlorinated ground waters. If the sample has been
chlorinated, add 0.5-mL 10% sodium thiosulfate per 1-L of sample at time of sample.
9.0 Quality Control
9.1 Each laboratory that uses Method 1602 is required to operate a formal quality assurance (QA)
program. The minimum QA requirements consist of an initial demonstration of laboratory
capability through performance of the initial precision and recovery (IPR) test (Section 9.3),
analysis of spiked samples to evaluate and document data quality, and analysis of standards and
blanks as tests of continued acceptable performance. Laboratory performance is compared to
established performance criteria to determine if the results of analyses meet the performance
criteria of the method. Specific quality control (QC) requirements for Method 1602 are provided
below. General recommendations on QA and QC for facilities, personnel, laboratory equipment,
instrumentation, and supplies used in microbiological analyses are provided in the USEPA
Microbiology Methods Manual, Part IV, C (Reference 17.3).
9.2 General QC requirements—All spiked QC samples must be spiked with enumerated sewage
filtrate or equivalent (Section 11).
9.2.1 Initial precision and recovery (IPR). The laboratory shall demonstrate the ability to
generate acceptable performance with this method by performing an IPR test before
April 2001 10
-------
Method 1602: Single Agar Layer (SAL) Procedure
analyzing any field samples. The procedure for performing the IPR is described in
Section 9.3.
9.2.2 Method blanks. The laboratory shall analyze method blanks (reagent water sample
containing no coliphage) to demonstrate freedom from contamination. The procedures and
criteria for analysis of a method blank are described in Section 9.4. The laboratory shall
analyze one method blank with each analytical batch. An analytical batch is defined as all
samples analyzed during a single day, up to a maximum of 20 samples (field samples and
matrix spike samples) per coliphage type.
9.2.3 Matrix spikes (MS). The laboratory shall spike a separate sample aliquot from the same
ground water source to monitor method performance. This MS test is described in Section
9.5. The laboratory shall analyze one MS sample (Section 9.5) when samples are first
received from a ground water source for which the laboratory has never before analyzed
samples. The MS analysis is performed on an additional (second) sample aliquot collected
from the ground water source at the same time as the routine field sample. If the laboratory
routinely analyzes samples from one or more ground water sources, one MS analysis must
be performed per 20 field samples. For example, when a laboratory receives the first
sample from a source, the laboratory must obtain a second aliquot of this sample to be
used for the MS. When the laboratory receives the 20th sample from this site, a separate
aliquot of this 20th sample must be collected and spiked.
9.2.4 Ongoing precision and recovery (OPR). The laboratory shall, on an ongoing basis,
demonstrate through analysis of OPR samples (Section 9.6) that the analytical system is in
control. The laboratory shall analyze one OPR sample for each analytical batch. An
analytical batch is defined as all samples analyzed during a single day, up to a maximum
of 20 samples (field samples and matrix spike samples) per coliphage type. Please note:
the OPR serves as the positive control for Method 1602.
9.2.5 Method modification validation/equivalency demonstration requirements. Method
1602 is a performance-based method and the laboratory is permitted to modify certain
method procedures to improve performance or lower the costs of measurements, provided
that all quality control (QC) tests cited in Section 9.2.5 are performed and all QC
acceptance criteria are met. The laboratory is not permitted to modify the double agar
layer QC spiking suspension enumeration procedure (Section 11.3).
9.2.5.1 Method modifications at a single laboratory. Each time a modification is
made to this method for use in a single laboratory, the laboratory is required to
validate the modification according to Tier 1 of EPA's performance-based
measurement system (PBMS) (Table 3 and Reference 17.6) to demonstrate that
the modification produces results equivalent or superior to results produced by
this method as written. Briefly, each time a modification is made to this method,
the laboratory is required to demonstrate acceptable modified method
performance through the IPR test (Section 9.3). IPR results must meet the QC
acceptance criteria in Table 2 in Section 14, and should be comparable to
previous results using the unmodified procedure. Although not required, the
laboratory also should perform a matrix spike/matrix spike duplicate
(MS/MSD) test (Section 9.7) to demonstrate the performance of the modified
method in at least one real-world matrix before analyzing field samples using the
modified method.
9.2.5.2 Method modifications for nationwide approval. If the laboratory or a
manufacturer seeks EPA approval of a method modification for nationwide use,
the laboratory or manufacturer must validate the modification according to Tier
2 of EPA's PBMS (Table 3 and Reference 17.6). Briefly, at least three
11 April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
laboratories must perform IPR tests (Section 9.3) and MS/MSD tests (Section
9.7) using the modified method, and all tests must meet the QC acceptance
criteria specified in Tables 2 in Section 14. Upon nationwide approval,
laboratories electing to use the modified method still must demonstrate
acceptable initial and ongoing performance in their laboratory according to the
requirements in Section 9.2.
9.2.6 Media sterility check. The laboratory shall test media sterility by incubating one unit
(tube or plate) of each batch of medium at 36°C ± 1.0°C for 48 to 72 hours and observing
for growth. Also, if media is stored in the refrigerator after sterilization, the media must be
stored overnight at room temperature and all media with growth discarded.
9.2.7 Record maintenance. The laboratory shall maintain records to define the quality of data
that are generated. Development of accuracy statements is described in Sections 9.5 and
9.6. The laboratory shall maintain a record of the date and results of all QC samples
described in Section 9.2. A log book containing reagent and material lot numbers should be
maintained along with samples analyzed using each of the lots.
9.2.8 Performance studies. The laboratory should periodically analyze an external QC sample,
such as a performance evaluation (PE) samples when available. The laboratory also should
participate in available interlaboratory performance studies conducted by local, state, and
federal agencies or commercial organizations. The laboratory should review results,
correct unsatisfactory performance, and record corrective actions.
9.2.9 The specifications contained in this method can be met if the analytical system is
maintained under control.
9.3 Initial precision and recovery (IPR)—The IPR test is performed to demonstrate acceptable
performance with the method as written prior to analysis of field samples or to evaluate acceptable
performance of a method modification. IPR tests must be accompanied by analysis of a method
blank (Section 9.4). All spiked QC samples must be spiked with enumerated sewage filtrate or
equivalent (Section 11).
9.3.1 A total of four reagent water samples for each coliphage type are required for the IPR test.
The target spike concentration is 80 PFU per sample.
9.3.2 IPR samples must be spiked in bulk. For each coliphage type (somatic and F+), use an
appropriate volume of the enumerated sewage filtrate stock spiking suspension (or
equivalent) prepared in Section 7.4.3 and enumerated in Section 11, to spike a 400-mL
"bulk" reagent water sample. Spike approximately 320 male-specific or somatic
coliphages per 400-mL bulk reagent water sample to achieve the target spike concentration
of approximately 80 PFU / sample and swirl to mix. Aliquot each bulk sample into four,
100-mL samples (see Section 11 for enumeration of coliphage stock and Section 13.2 for
spiking volume calculations).
9.3.3 Analyze the four spiked 100-mL samples per coliphage type using the SAL procedure
(Section 12).
9.3.4 Compute the coliphage percent recovery in each sample using the following equation:
N
R = 100 x —
where
R = percent recovery
N = number of coliphage detected (PFU / sample)
T = number of coliphage spiked (PFU / sample)
April 2001 12
-------
Method 1602: Single Agar Layer (SAL) Procedure
9.3.5 Using all four sample results for each coliphage type from an IPR test, compute the
average percent recovery (x) and the relative standard deviation of the recovery (RSDr).
(See glossary for definition of RSDr.) Compare RSDr and X with the corresponding limits
for IPR (Section 14). If RSDr and x meet the acceptance criteria, the system performance
is acceptable and analysis of samples may begin. If RSDr or x falls outside the range,
system performance is unacceptable. In this event, identify and correct the problem and
repeat the test.
9.4 Method blank—Performed at the frequency specified in Section 9.2.2.
9.4.1 For each coliphage type, prepare and analyze a reagent water sample containing no
coliphage using the same procedure as used for analysis of the field or QC samples.
9.4.2 If coliphage, or any potentially interfering organisms are found in the blank, analysis of
additional samples must be halted until the source of contamination is eliminated, and a
repeat of the method blank analysis shows no evidence of contamination. Any sample in a
batch associated with a contaminated blank should be recollected (if holding times have
been violated) and reanalyzed. Samples from a batch that proves to have no coliphage in
its blank may be reported.
9.5 Matrix spike (MS)—The laboratory shall spike and analyze a field sample aliquot to determine
the effect of the matrix on the method's coliphage recovery. The MS shall be analyzed according to
the frequency in Section 9.2.3. All spiked QC samples must be spiked with enumerated sewage
filtrate or equivalent (Section 11).
9.5.1 For each coliphage type, analyze an unspiked, 100-mL field sample according to the SAL
quantitative procedure (Section 12). For each coliphage type, add approximately 80 PFU
to a second, 100-mL aliquot of the same field sample (see Section 11 for enumeration of
coliphage stock and Section 13.2 for spike volume calculations).
9.5.2 Compute the percent recovery (R) of coliphage using the following equation:
R= 100x(Nsp-NusP)/T
where
R is the percent recovery
Nsp is the number of coliphage detected in the spiked sample
Nusp is the number of coliphage detected in the unspiked sample
T is the number of coliphage spiked
9.5.3 Compare the coliphage recovery with the corresponding limits in Section 14. If the
recovery for coliphage falls outside its limit, method performance is unacceptable for that
sample. If the results for the OPR sample associated with this batch of samples are within
their respective control limits, a matrix interference may be causing poor recovery. If the
results for the OPR are not within their control limits, the laboratory is not in control. The
problem must be identified and corrected. The matrix spike and associated field sample(s)
should be reanalyzed. The recovery should be maintained on a control chart and updated
on a regular basis.
9.6 Ongoing precision and recovery (OPR)—Performed at the frequency specified in
Section 9.2.4. All spiked QC samples must be spiked with enumerated sewage filtrate or equivalent
(Section 11). Please note, the OPR serves as the positive control for Method 1602.
13 April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
9.6.1 For each coliphage type, spike one, 100-mL reagent water sample with approximately
80 PFU of coliphage (see Section 1 1 for enumeration of coliphage stock and Section 13.2
for spike volume calculations).
9.6.2 Analyze the spiked samples using the SAL procedure (Section 12).
9.6.3 Compute the percent recovery of coliphage in each OPR sample using the following
equation:
N
R = 100 x —
where
R = percent recovery
N = the number of coliphage detected
T = the number of coliphage spiked
9.6.4 Compare R with the corresponding limits for ongoing precision and recovery in Section
14. If R meets the acceptance criteria, system performance is acceptable and analysis of
samples may continue. If R falls outside the range for recovery, system performance is
unacceptable. Identify and correct the problem and perform another OPR test before
continuing with the analysis of field samples.
9.6.5 As part of the QA program for the laboratory, method precision for samples should be
assessed and records retained. After the analysis of five OPR samples for which the
reagent water spike recovery of coliphage is determined, the laboratory should compute the
average percent recovery (R) and the standard deviation of the percent recovery (sr).
Express the precision assessment as a percent recovery interval from R - 2 sr to R + 2 sr
for each coliphage type. For example, if R = 80% and sr = 30%, the accuracy interval is
expressed as 20% to 140%. The assessment should be maintained on a control chart and
updated on a regular basis.
9.7 Matrix spike/matrix spike duplicate (MS/MSD) — If IPR and MS/MSD test performance is
equal to or better than the criteria set forth in Table 2, then the modified version of the method is
acceptable.
9.7.1 For each coliphage type, analyze an unspiked, 100-mL field sample according to the SAL
quantitative procedure (Section 12). For each coliphage type, the laboratory shall spike
and analyze two identical field sample aliquots (MS and MSB samples), as described in
Section 9.5, using the modified version of the method.
9.7.2 For each coliphage type, calculate the percent recovery (R) using the equation in Section
9.5.2. Calculate the mean of the MS and MSB recoveries (RMS+RMSD]/2).
9.7.3 Calculate the relative percent difference (RPB) using the following equation:
A/m
where
RPB is the relative percent difference
NMS is the number of coliphage detected in the MS
NMSD is the number of coliphage detected in the MSB
Nmean is the mean number of coliphage detected in the MS and
MSB
April 2001 14
-------
Method 1602: Single Agar Layer (SAL) Procedure
9.7.4 Compare the mean MS/MSD recovery and RPD with the corresponding limits in Table 2
(Section 14) for each coliphage type.
10.0 Calibration and Standardization
10.1 At a minimum, check temperatures in water baths, refrigerators, -20°C freezers, and -70°C
freezers daily to ensure operation within stated limits of method and record daily measurements in
a log book.
10.2 At a minimum, check temperatures in incubators twice daily, at least 4 hours apart, to ensure
operation within stated limits of method and record measurements in log book.
10.3 Check thermometers at least annually against an NIST-certified thermometer or one that meets the
requirements of NIST Monograph SP 250-23. The mercury column should not be separated.
10.4 Calibrate pH meter prior to use, using standards of pH 4.0, 7.0, and 10.0. To calibrate, use the two
standards that are nearest to the desired pH.
10.5 Calibrate balances annually using ASTM-certified Class 2 reference weights.
10.6 Calibrate spectrophotometer prior to each use, following method described in owner's manual. Use
sterile TSB without antibiotics as the blank.
10.7 Laboratories must adhere to all applicable quality control requirements set forth in Reference 17.4.
11.0 Enumeration of Coliphage QC Spiking Suspensions
11.1 The double agar layer (DAL) procedure is used to enumerate stock suspensions of somatic and
male-specific coliphage for use in spiking quality control samples.
11.2 Dilution of coliphage stock (Section 7.4.1 or 7.4.2) or sewage filtrate (Section 7.4.3)—A minimum
of four different volumes/dilutions are necessary for the double agar layer (DAL) enumeration of
the coliphage stock or sewage filtrate (Section 18, Flow chart 2):
Undiluted
• 0.1
• 0.01
• 0.001
Additional dilutions may be necessary. TSB without antibiotics (Section 7.3.1.1) is used as the
diluent and as the method blank.
11.2.1 Aseptically add 9.0 mL of TSB without antibiotics (Section 7.3.1.1) into each of four
(or more) sterile dilution tubes (Section 6.2.1). Label them as "0.1," "0.01," "0.001,"
"method blank," etc.
11.2.2 Add 1.0 mL of the coliphage stock or sewage filtrate to the tube of TSB labeled "0.1."
Cap the tube and vortex for 5 seconds on a medium-high setting (if available) or until
well-mixed.
11.2.3 Add l.OmL of the well-mixed 0.1 dilution to atube with 9 mL of TSB labeled "0.01".
Cap the tube and vortex for 5 seconds on a medium-high setting (if available) or until
well-mixed.
15 April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
11.2.4 Add 1.0 mL of the well-mixed 0.01 dilution to atube with 9 mL of TSB labeled
"0.001." Cap the tube and vortex for 5 seconds on a medium-high setting (if available)
or until well-mixed.
11.2.5 Add 1.0 mL of TSB without antibiotics (Section 7.3.1.1) to the tube labeled "method
blank." Cap the tube and vortex for 5 seconds on a medium-high setting (if available) or
until well-mixed.
11.3 Coliphage spiking stock suspension enumeration by double agar layer (DAL) procedure (Section
18, Flow chart 3)—In this procedure, a tube of molten 0.7% TSA "top agar" with added host
bacteria is inoculated with coliphage stock and will be poured into a 1.5% TSA "bottom agar"
plate. Four dilutions of coliphage stock or sewage filtrate will be analyzed in duplicate for each
coliphage type. As a result, nine double-agar layer plates will be required for each coliphage type:
two plates per dilution (undiluted, 0.1, 0.01, and 0.001) and one method blank plate. Please note:
Laboratories are not permitted to modify or omit any aspects of the coliphage stock enumeration
procedure (Section 11.3). As a result, magnesium chloride or calcium chloride must not be
added the sample or media.
11.3.1 Agar preparation
11.3.1.1 Place 0.7% TSA top agar tubes with antibiotics (Section 7.3.3.1 and
7.3.3.2) in a 45°C to 48°C water bath. The top agar should remain molten
in the water bath until ready for use. 18 tubes are necessary to enumerate
four dilution volumes in duplicate for each phage. The 18 tubes also
includes an additional method blank tube for each phage type .-Nine of the
top agar tubes should contain nalidixic acid (Section 7.3.3.1) for growth
of E. coll CN-13; the other nine should contain ampicillin/streptomycin
(Section 7.3.3.2) for growth of E. coll Famp.
11.3.1.2 As a precaution against contamination, disinfect a workspace near the
water bath with a 1 : 100 dilution of household bleach and allow to dry. If
workspace can be corroded by bleach use an ethanol solution of 70% or
greater.
11.3.1.3 Assemble 1.5% TSA bottom agar plates (Section 7.3.2) and label so that
the following information is identifiable:
• Dilution of stock filtrate or method blank
Bacterial host (E. coll CN-13 or E. coll Famp)
• Coliphage type (somatic for the E. coll CN-13 bacterial host or
male-specific for the E. coll Famp bacterial host)
Date
• Time
Please note: The following steps are critical. To ensure viability of bacterial host and coliphage, do not
add bacterial host and coliphage spiking suspension filtrate until ready to plate.
11.3.2 Preparation of plates for enumeration of somatic coliphage
11.3.2.1 With the top agar tube still in the water bath, aseptically inoculate a top
agar tube containing nalidixic acid with 100 yL of log-phase
E. coll CN-13.
11.3.2.2 Immediately add 500 (iL (0.5 mL) of undiluted coliphage stock or sewage
filtrate.
11.3.2.3 Mix the inoculum by rolling the tube briefly in palm of hand.
April 2001 16
-------
Method 1602: Single Agar Layer (SAL) Procedure
11.3.2.4 Pour contents into one of the two bottom agar plates marked "undiluted,
E. coli CN-13, somatic."
11.3.2.5 Duplicate analysis—Repeat Sections 11.3.2.1 through 11.3.2.4 forthe
duplicate.
11.3.2.6 Repeat Sections 11.3.2.1 through 11.3.2.5 for each dilution volume.
11.3.3 Preparation of plates for enumeration of male-specific (F+) coliphage—Repeat Section
11.3.2 using agar containing ampicillin/streptomycin and log-phase E. coli F^p
11.3.4 Preparation of somatic coliphage method blank
11.3.4.1 With the top agar tube still in the water bath, aseptically inoculate a top
agar tube containing nalidixic acid with 100 \\L of log-phase
E. coli CN-13.
11.3.4.2 Immediately add 500 ^L (0.5 mL) of TSB from the "method blank"
dilution tube.
11.3.4.3 Mix the inoculum by rolling the tube briefly in palm of hand.
11.3.4.4 Pour contents into a bottom agar plate marked "method blank,
E. coli CN-13, somatic."
11.3.5 Preparation of the male-specific (F+) coliphage method blank—Repeat Section 11.3.4
using agar containing ampicillin/streptomycin and log-phase E. coli Famp.
11.3.6 Store undiluted coliphage stock or sewage filtrate at 4°C ± 1.0°C for use in preparing
new dilutions for positive controls, IDC, ODC, and MS samples.
11.3.7 After the top agar hardens, cover, invert the plates and incubate for 16 to 24 hours at
36°C± 1.0°C.
11.3.8 Circular zones of clearing (typically 1 to 10 mm in diameter) in lawn of host bacteria
after 16 to 24 hours of incubation are plaques. Count the number of plaques on each
plate. Please note: The use of a light box (Section 6.4.8) to evaluate results is
recommended.
11.3.9 Proceed to Section 13.1 and calculate the PFU / mL for each coliphage.
11.3.10 Use the enumerated somatic and male-specific stocks to spike the single agar layer IPR,
OPR, MS, and positive control samples as described in Section 9.
17 April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
12.0 Single Agar Layer (SAL) Procedure for Sample Analysis
(Procedures in Section 12 Also Are Summarized in Flow Chart 4)
12.1 Refer to Section 7.5.4 for preparation of log-phase host bacterial cultures.
12.2 Preparation of media for te sting
12.2.1 Prepare 100 mL of 2X TSA with nalidixic acid for E. coll CN-13 as described in
Section 7.3.4.2.
12.2.2 Add the 100 mL of 2X TSA with nalidixic acid to a 250-mL to 500-mL size Erlenmeyer
flask and place in a 45°C to 48°C water bath to equilibrate. The liquid in the waterbath
must come up to the level of the media. To ensure that the flask does not tip-over in the
waterbath, the use of a flask weight (Section 6.2.25) is recommended.
12.2.3 Prepare 100 mL of 2X TSA with ampicillin/streptomycin for E. coll Famp as described
in Section 7.3.4.3.
12.2.4 Add the 100 mL of 2X TSA with ampicillin/streptomycin to a 250-mL to 500-mL size
Erlenmeyer flask and place in a 45°C to 48°C water bath to equilibrate.
12.2.5 Keep the agar molten between 45°C and 48°C until use in the SAL assay.
12.2.6 Prepare method blanks as specified in Section 9.4.
12.3 As a precaution against contamination, disinfect a work space near the water baths with a 1 : 100
dilution of household bleach and allow to dry. If workspace can be corroded by bleach use an
ethanol solution of 70% or greater.
12.4 Assemble and label plates with bacterial host (E. coll CN-13 or E. coll Famp), date, and time.
12.5 Addition of sample and host bacteria to SAL media
12.5.1 Dispense two, 100-mL aliquots of sample into separate, sterile, 250-mL to 500-mL size
Erlenmeyer flasks. Also dispense 100 mL of reagent water into a third 250-mL to
500-mL size Erlenmeyer flask (this will be used to determine sample temperature
changes in the following steps and will be referred to as the "temperature flask").
12.5.2 Add 0.5 mL of sterile stock magnesium chloride (Section 7.1.3) to each sample flask
(not the temperature flask).
12.5.3 Place the flasks into the 36 °C ± 1.0 °C water bath for 5 minutes or until sample water
just reaches the water bath temperature according to the temperature flask.
Please note: All components should be warmed before assay to avoid solidification prior to pouring
plates. Also, The following steps are critical. Temperature must be monitored closely to ensure that
coliphages are not inactivated and also to ensure that the agar does not harden prematurely.
12.5.4 Add 10 mL of log-phase E. coll CN-13 (Section 7.5.4) to one flask of sample water.
12.5.5 Add 10 mL of log-phase E. coll Famp (Section 7.5.4) to the other flask of sample water.
12.5.6 Add an additional 10 mL of water to the temperature flask (110 mL total).
12.5.7 Immediately transfer temperature flask and flasks containing sample and log-phase
bacteria to the 45°C to 48°C water bath. The approximate temperature of the samples
should be determined by monitoring the temperature of the water in the temperature
flask. When water in the temperature flask reaches 43°C ± 1.0°C, remove samples from
the water bath and proceed to the next step immediately.
April 2001 18
-------
Method 1602: Single Agar Layer (SAL) Procedure
Please note: During the single agar layer procedure, the sample and host bacteria should not remain in
contact with each other for more than 10 minutes prior to plating. After plating, the agar must harden
within 10 minutes. Increased contact time or agar-hardening time may result in replication ofphages
such that the initial phage concentration is overestimated. The entire plating procedure from combining
sample with host to hardening of single-agar layer plates should not exceed 20 minutes. Samples also
should remain in contact with host for a minimum of three minutes before plates are poured.
12.5.8 Add the sample/E. coll CN-13 mixture to the 100 mL of 2X TSA containing nalidixic
acid. Allow sample/E. coli CN-13 mixture to remain in contact with host for a minimum
of three minutes before plating.
12.5.8.1 Pour the contents into a series of petri dishes at 20 mL per
100-mm-diameter dish or 40 mL per 150-mm-diameter dish. (This
procedure requires either five,150-mm plates or ten,100-mm plates per
100-mL sample.)
12.5.9 Combine the sample/E. coli F^p mixture with the 100 mL of 2X TSA containing
ampicillin/streptomycin. Allow sample/E. coli Famp mixture to remain in contact with
host for a minimum of three minutes before plating.
12.5.9.1 Pour the contents into a series of petri dishes at 20 mL per 100-mm
diameter dish or 40 mL per 150-mm dish. Please note: Plates should be
dry before they are inverted, as condensation drops on the agar surface
may appear to be plaques. When reading plates examine plaques
closely.
12.5.10 Allow the agar to harden, cover, invert, and incubate for 16 - 24 hours at 36°C ± 1.0°C.
12.5.11 Circular zones of clearing (typically 1 to 10 mm in diameter) in lawn of host bacteria in
SAL plates after 16-24 hours are considered to be plaques. Count all plaques per plate
series, record results, and go to Section 13.3 for calculation of PFU / 100 mL. Please
note: The use of a light box (Section 6.4.8) to evaluate sample results is recommended.
12.6 Spot plate plaque confirmation procedure—Although not required, laboratories may use the spot
plate procedure for confirmation of plaques if one or more such plaques on a single agar layer plate
are questionable.
12.6.1 Pick plaque(s) with a sterile Pasteur (or other) pipette and transfer it to a tube with
0.5 mL TSB (Section 7.3.1.1).
12.6.2 Allow the inoculated broth to stand 5 minutes at room temperature.
12.6.3 Cap the tube and vortex for 5 seconds on a medium-high setting (if available) or until
well-mixed.
12.6.4 Prepare spot plates according to Section 7.3.4. Once prepared, spot plates may be used
on the same day or held at 4°C ± 1°C for up to 4 days prior to use.
12.6.5 Spot 10 microliters of inoculated broth to a spot plate with appropriate E. coli host,
using the same E. coli host on which the phage was initially isolated. Record spot time.
12.6.6 Spot the method blank and positive control samples as specified in Section 9.4 and 9.5
of the April 2001 version of Method 1601 (Reference 17.7).
12.6.7 Allow inocula to absorb into medium. This will take approximately 30 to 60 minutes.
The inocula must not be allowed to run across the plate.
12.6.8 After inocula absorption, cover, invert, and incubate the plate at 36°C ± 1.0°C for 16 to
24 hours.
12.6.9 Lysis zone formation (typically a circular zone of clearing) indicates confirmation for
19 April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
coliphages. If the spot contains an intact lawn of bacteria indistinguishable from the
background lawn of bacteria, this indicates a negative result. However, other outcomes
of the spot assay are possible. A positive confirmation also may appear as one or more
small plaques or areas of clearing of the host bacteria lawn within the spot, despite the
presence of some portion of the host bacteria lawn within the spot. A positive result may
also appear as a zone of lysis containing small, discrete colonies of bacteria within the
spot. These bacterial colonies are from phage-resistant mutants. Please note: The use of
a light box (Section 6.4.8) to evaluate sample results is recommended.
13.0 Data Analysis and Calculations
13.1 Calculation of QC sample spiking suspension concentrations from the double agar layer (DAL)
enumeration procedure (Section 1 1)
1 3.1 .1 The number of plaque forming units (PFU) per mL in the coliphage spiking suspension
will be calculated using DAL plates that yield plaque counts within the desired range of
zero to 300 PFU per plate for male-specific (F+) coliphage and zero to 100 PFU per plate
for somatic coliphage. There may be occasions when the total number of plaques on a
plate will be above the ideal range. If the count exceeds the upper range or if the plaques
are not discrete, results should be recorded as "too numerous to count" (TNTC).
1 3.1 .2 For each coliphage type, sum the number of PFU from all dilutions with plaques (on either
of the duplicate plates), excluding dilutions with all TNTC or all zeros. (See equation in
Section 13.1.5)
1 3.1 .3 Sum the undiluted sample volumes used to inoculate all replicate plates at all dilutions
having useable counts (as defined above). (See equation in Section 13.1.5)
1 3.1 .4 Divide the sum of the PFU by the sum of the undiluted sample volume to obtain
PFU/ mL in the spiking suspension. (See equation in Section 13.1.5)
13.1.5 The equation for Sections 13.1.1 through 13.1.4 is as follows:
Undiluted spiking suspension PFU / mL = (PFU! + PFU2... PFUJ/^ + V2.... Vn)
Where:
• PFU = number of plaque forming units from plates of all countable sample
dilutions (dilutions with 1 or more PFU per plate, excluding dilutions
with all TNTC or all zeros (0)
• V= volume of undiluted sample in all plates with countable plaques
• n = number of useable counts
April 2001 20
-------
Method 1602: Single Agar Layer (SAL) Procedure
Table 1.
Example DAL data
Dilution
Undiluted
1 : 10
1 : 100
1 : 1,000
PFU / plate (for each duplicate
plate)
TNTC, TNTC
35, 37
0,3
0, 0
Volume of undiluted spiking suspension (ml_)
0.5ml
0.05
0.005
0.0005
Example: (35 + 37 + 0 + 3)/(0.05 + 0.05 + 0.005 + 0.005) = 75/0.11 = 682 PFU / mL
In this example, the undiluted spiking suspension contains approximately 682 PFU per
mL, the 1:10 dilution contains approximately 68.2 PFU per mL, the 1 :100 dilution
contains approximately 6.82 PFU per mL, and the 1 : 1000 dilution contains
approximately 0.682 PFU per mL.
13.2 Calculation for preparing IPR, OPR, MS, and positive control spikes
13.2.1 Use a dilution of the QC sample spiking suspension that will result in a bulk spike volume
between 0.1 and 3.0 mL for the spike concentration specified in Section 9.
13.2.2 Use the following equation to determine the spiking volume:
s =
where,
S =
T =
B =
(Q
Spike volume (mL)
Target number of coliphage per sample (PFU)
Number of samples that will be spiked (only necessary when multiple QC
samples are spiked in bulk)
C = Concentration (PFU/mL) in the dilution to be used for spiking
13.2.3 For example, for the IPR test (Section 9.3):
T) A spike dose of 80 PFU is needed per 100-mL sample
B) A total of four, 100-mL samples will be spiked at the same time
C) The undiluted spiking solution contains 682 PFU / mL
The equation would be solved as follows:
s =
(80 PFU)(4)
(682 PFU/mL)
= 0.47 mL
21
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
As a result, 0.47 mL of the undiluted spiking suspension would be spiked into the
400-mL bulk sample. The 400-mL bulk sample would be mixed and four, 100-mL aliquots
dispensed. Each 100-mL sample should contain approximately 80 PFU.
13.3 Calculation for the SAL procedure (Section 12)
13.3.1 The SAL method (SAL) has been validated for use with 100 mL sample volumes. 100% of
each sample should be plated.
13.3.2 For each sample, count the total number of plaques from all plates. If the plaques are not
discrete, results should be recorded as "too numerous to count" (TNTC). The remaining
sample should be diluted, as appropriate, and re-analyzed.
13.3.3 Total number of plaques per 100 mL sample = PFU / 100 mL.
14.0 Method Performance
14.1 The QC acceptance criteria listed in Table 2 are based on data generated through the
interlaboratory validation of Method 1602 involving 10 laboratories and 10 raw ground water
matrices.
Table 2.
Quality control acceptance criteria
Performance test
Initial precision and recovery (IPR) (Section 9.3)
Mean percent recovery
Precision (as maximum relative standard deviation)
Ongoing precision and recovery (OPR) as percent recovery (Section 9.6)
Matrix spike (MS) (Section 9.5)
MS percent recovery
Matrix spike, matrix spike duplicate (MS/MSD) (Section 9.7)
Mean percent recovery for MS/MSD
Precision (as maximum relative percent difference of MS/MSD)
Male-specific
acceptance
criteria
9% -130%
46%
4% -135%
Detect -120%
Detect -120%
57%
Somatic
acceptance
criteria
86% -177%
23%
79% -183%
48% -291%
48% -291%
28%
14.2 Method 1602 is a performance-based method and the laboratory is permitted to modify certain
method procedures to improve performance or lower the costs of measurements, provided that all
quality control (QC) tests cited in Section 9.2.5 are performed and all QC acceptance criteria are
met. The laboratory is not permitted to modify the double agar layer QC spiking suspension
enumeration procedure (Section 11.3).
14.2.1 Method modifications at a single laboratory. Each time a modification is made to this
method for use in a single laboratory, the laboratory is required to validate the
modification according to Tier 1 of EPA's performance-based measurement system
(PBMS) (Table 3 and Reference 17.6).
April 2001
22
-------
Method 1602: Single Agar Layer (SAL) Procedure
14.2.2 Method modifications for nationwide approval. If the laboratory or a manufacturer
seeks EPA approval of a method modification for nationwide use, the laboratory or
manufacturer must validate the modification according to Tier 2 of EPA's PBMS (Table 2
and Reference 17.6). Please note: After a method modification is validated for nationwide use,
each individual laboratory electing to use the modification still must demonstrate acceptable
initial and on-going performance with the modified method through the analysis of method
blanks, media sterility checks, positive controls, ODC samples, and MS samples.
Table 3.
Tier 1 and Tier 2 Validation/Equivalency Demonstration Requirements
Test
IPR
(Section 9.3)
Method blank
(Section 9.4)
MS/MSD
(Section 9.7)
Description
4 replicates of spiked
reagent water
Unspiked reagent
water
2 replicates of spiked
matrix water
Tier 1 modification'1'
Required. Must be accompanied by a
method blank.
Required
Recommended, but not required. Must be
accompanied by an unspiked field sample
collected at the same time as the MS
sample
Tier 2 modification'2'
Required per laboratory
Required per laboratory
Required per laboratory.
Each laboratory must
analyze a different water.
Please note:
(1) If a modification will be used only in one laboratory, these tests must be performed and the results must
meet all of the QC acceptance criteria in the method (these tests also are required the first time a
laboratory uses the validated version of the method). After the initial demonstration that the modification is
equivalent to the procedure specified in this method, the laboratory must continue to demonstrate
acceptable ongoing performance with the modified method through the analysis of media sterility checks,
method blanks, positive controls, ODC samples, and MS samples.
(2) If nationwide approval of a modification is sought for one type of water matrix (such as ground water), a
minimum of 3 laboratories must perform the tests and the results from each lab individually must meet all
QC acceptance criteria in the method. If more than 3 laboratories are used in a study, a minimum of 75%
of the laboratories must meet all QC acceptance criteria.
15.0 Pollution Prevention
15.1 The solutions and reagents used in this method pose little threat to the environment when recycled
and managed properly.
15.2 Solutions and reagents should be prepared in volumes consistent with laboratory use to minimize
the volume of expired materials to be disposed.
16.0 Waste Management
16.1 The laboratory is responsible for complying with all Federal, State, and local regulations governing
waste management, particularly hazardous waste identification rules and land disposal restrictions,
and for protecting the air, water, and land by minimizing and controlling all releases from fume
hoods and bench operations. Compliance with all sewage discharge permits and regulations is also
required. An overview of requirements can be found in Environmental Management Guide for
Small Laboratories (EPA 233-B-98-001).
16.2 Samples, reference materials, and equipment known or suspected to have bacteriophage attached or
contained must be sterilized prior to disposal.
23
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
16.3 For further information on waste management, consult The Waste Management Manual for
Laboratory Personnel and Less Is Better: Laboratory Chemical Management for Waste
Reduction, both available from the American Chemical Society's Department of Government
Relations and Science Policy, 1155 16th Street N.W., Washington D.C. 20036.
17.0 References
17.1 American Public Health Association, American Water Works Association, Water Environment
Federation. Washington, D.C. Joint Task Group for Section 9224, 1997. Detection of Coliphages.
For Standard Methods for the Examination of Water and Waste Water 20th Edition Supplement.
(draft version - December 1997)
17.2 American Public Health Association, American Water Works Association, and Water Environment
Federation. 1995. Standard Methods for Water and Wastewater. 20th Edition. Sections 9020,
9030, 9040, 9050, and 9221.
17.3 Bordner, R., J.A. Winter, and P.V. Scarpino (eds.). 1978. Microbiological Methods for
Monitoring the Environment, Water and Wastes. EPA-600/8-78-017. Office of Research and
Development. USEPA.
17.4 Manual for the Certification of Laboratories Analyzing Drinking Water, EPA 815-B-97-001,
Office of Ground Water and Drinking Water, Technical Support Center, U.S. Environmental
Protection Agency, 26 Martin Luther King Drive, Cincinnati, OH 45268.
17.5 Annual Book of ASTMStandards. Vol. 11.01. American Society for Testing and Materials.
Philadelphia, PA 19103.
17.6 USEPA. EPA Guide to Method Flexibility and Approval of EPA Water Methods, EPA 821-D-96-
004. Office of Water, Engineering and Analysis Division, Washington, DC 20460 (1996).
17.7 USEPA. Method 1601:Male-specific (F+) and Somatic Coliphage in Water by Two-Step
Enrichment Procedure. EPA 821-R-01-030. Office of Water, Engineering and Analysis Division,
Washington, DC 20460 (April 2001).
April 2001 24
-------
Method 1602: Single Agar Layer (SAL) Procedure
18.0 Flowcharts
We greatly appreciate Fred Williams (USEPA, Cincinnati, OH) for providing the original flow charts on
which all of the following flowcharts are based.
Flow chart 1. Preparation of log-phase host bacteria stock cultures (Section 7.5.4)
Add 25-30 mL of TSB with antibiotics to each shaker flask
Additional
30 minutes
incubation
CN1 CN2 CN3
TSB w/naldixic for somatics
F1 F2 F3
TSB w/amp & strep for male^pecifics
Add 0.1 -1.0 mL of host bacteria to each flask
0.1-14mL 0.1.1.0 mL
CB,
\
CN1 CN2 CN3
TSB w/naidixic for somatics
F1 F2 F3
TSB w/amp & strep for male^pecifics
Incubate in shaker at 36°C and 100-150 rpm for 4 hr
CN1 CN2 CN3
F1 F2 F3
Aseptically transfer 1.0 mL to cuvette and read
absorbance at 520 nm
1.0 mL
- If OD < 0.1
A
rODO.1-0.5 / \\ |
LJ •.!
CN1
I i lfOD<0.1 -
\ I lfOD0.1-Oi
Chill on wet ice or at 4°C
Additional
30 minutes
incubation
25
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
Flow chart 2. Dilution of coliphage QC spiking suspensions (Section 11.2)
| Add 10 ml_ of undiluted sewage filtrate
IT
undiluted
Add 9.0 ml TSB without antibiotics to each dilution tube
PI
undiluted 0.1 0.01 0.001
Vortex undiluted tube 5 seconds. Transfer 1.0 ml_ from undiluted tube to 0.1 tube.
1.0 mL
rr r IT r
undiluted 0.1 0.01 0.001
Vortex 0.1 tube 5 seconds. Transfer 1.0 ml from 0.1 tube to 0.01 tube.
1.0 mL
rr nt r ra
undiluted 0.1 0.01 0.001
Vortex 0.01 tube 5 seconds. Transfer 1 .0 mL from 0.01 tube to 0.001 tube.
1.0 mL
rr oi r en
undiluted 0.1 0.01 0.001
April 2001
26
-------
Method 1602: Single Agar Layer (SAL) Procedure
Flow chart 3. Coliphage spiking suspension enumeration by double agar layer (DAL) procedure
(Section 11.3)
Place eighteen 0.7% TSAtop agar tubes with antibiotics in 46.5°C water bath
nine for somatic
0.7%TSA»rfnaldixk: acid
nine for male-specific
0.7% TSA Wamp & strep
Undiluted 0.1 0.01 0.001 0.001 0.01 0.1 UndiMed
46.5 °C
Label eighteen corresponding 1.5% TSA bottom agar plates containing antibiotics
nine for somatic
1i%TSAWnaldixicaoid
nine for male^pecific
1.5% TSA w/amp & strep
:r3 0.01
3 "•'
^=3 UndiMed
Bbnt
For each TSA top agar tube in water bath complete steps A through D below:
A.
Add 100 uL (0.1 mL) log-phase
host bacteria to tube with
appropriate antibiotic
Famp
0.7%TSA with naldixic acid 0.7%TSA with amp/strep
C. Gently mix tube in palm
B. Immediately, add 500 uL (0.5 mL) from
appropriate coliphage stock dilution tube
(Flow chart 2)
For method blanks add
500 uL (0.5 mL) TSB instead
of coliphage stock dilution
0.7%TSAwith antibiotic
D. Pour tube into 1.5% TSA bottom agar plate with
appropriate antibiotic and label
Invert and incubate at 36°C for 16-24 hr
CN.13 and naidixic acid
for somatic
Famp and amp/strep
for male-specific
ojjol 6
0.01 E
o.i E
UndilJted 6
36°C
^==3 0.001
E9 0.01
EE§ o.i
5ES UndilJted
Bbnk
After incubation, count plaques, and record results
CN-13 Famp
27
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
Flow chart 4. Single agar layer (SAL) enumeration procedure for 100-mL samples (Section 12)
Place 2X ISA with antibiotics in
"I 46.5°C water bath to equilibrate
2XTSAw/naldixic 2XTSAWamp& strep
46.5°C
2d
100 ml Samples
for somatics (CN) X^X for male^pecifics (F)
100 mL
Reagent Water
100mL
, Reagent Water t
100 mL
Reagent Water
CN1 CN2 CN3
2b
Add 0.5 mL stock magnesium chloride
CN1 CN2 CN3 ^—-> F1 F2 F3
Temp
Place in 36°C water bath for 5 min
Add 10mL
log-phase CN-13
Add 10 mL
tog-phase Fan
36°C
2e
Transfer to 46.5°C water bath
46.5°C
Add samples and blanks to the 2X
TSA from Step 1, swirl, and pour plates
2XTSA
Wnaldixic
2XTSA
vg/amp & strep
Z[ Invert and incubate at 36°C for 16-24 hr
CN.13
After incubation, count plaques,
and record results
CN-13
April 2001
28
-------
Method 1602: Single Agar Layer (SAL) Procedure
19.0 Glossary
These definitions and purposes are specific to this method but have been conformed to common
usage as much as possible.
19.1 Symbols
#
ox.
degrees Celsius
micro
number
percent
19.2 Alphabetical characters and acronyms
ASTM American Society for Testing and Materials
CFR Code of Federal Regulations
DAL double agar layer method
DOT Department of Transportation
g gram
HC1 hydrochloric acid
IPR initial precision and recovery
KH2HPO4 potassium phosphate
L liter
M molar
mg milligram
MgCl2*6H2O magnesium chloride hexahydrate
mL milliliter
mm millimeter
MPN most probable number
MS matrix spike
NaOH sodium hydroxide
Na2S2O3 sodium thiosulfate
NIST National Institute of Standards and Technology
nm nanometer
OD optical density
OPR ongoing precision and recovery
OSF£A Occupational Safety and Health Administration
PFU plaque forming unit
psi pounds per square inch
QA quality assurance
QC quality control
rpm revolutions per minute
SAL single agar layer method
TNTC too numerous to count
TSA tryptic soy agar
TSB tryptic soy broth
USEPA United States Environmental Protection Agency
X "times"
29
April 2001
-------
Method 1602: Single Agar Layer (SAL) Procedure
19.3 Additional definitions
Accuracy—A measure of the degree of conformity of a single test result generated by a specific
procedure to the assumed or accepted true value and includes both precision and bias.
Analyte—The organism tested for by this method. The analyte in this method is coliphage.
Bias—the persistent positive or negative deviation of the average value of a test method from the
assumed or accepted true value.
Coliphage—Viruses that infect E. coli.
Host bacteria—Are those bacteria that allow the bacteriophage to penetrate and replicate within
them, ultimately lysing, resulting in the release of the progeny bacteriophage. Host bacteria are
essential for virus replication. The hosts used in this method are: E. coli CN-13, and
E. coli Famp (E. coli HS(pFamp)R).
Initial precision and recovery (IPR)—The IPRtest is performed to establish the ability to
demonstrate control over the analytical system and to generate acceptable precision and recovery.
Male-specific coliphage—Viruses (bacteriophages) that infect coliform bacteria only via the
F-pilus.
Method blank—An aliquot of reagent water that is treated exactly as a sample and carried through
all portions of the procedure until determined to be negative or positive. The method blank is used
to determine if the sample has become contaminated by the introduction of a foreign
microorganism through poor technique.
Ongoing precision and recovery—A reagent water sample method blank spiked with known
quantities of analytes. The OPR is analyzed exactly like a sample. Its purpose is to assure that the
results produced by the laboratory remain within the limits specified within this method for
precision and recovery.
Plaque—Circular zones of clearing (typically 1 to 10 mm in diameter) in lawn of host bacteria in
SAL and DAL plates after incubation.
Precision—The degree of agreement of repeated measurements of the same property, expressed in
terms of dispersion of test results about the arithmetical mean. Results are obtained by repetitive
testing of a homogeneous sample under specified conditions. The precision of a test method is
expressed quantitatively as the standard deviation computed from the results of a series of
controlled determinations.
Relative Standard Deviation (RSD)—The standard deviation times 100 divided by the mean.
Reagent water—Water conforming to Specification D 1193, Annual Book of ASTM Standards
(Reference 17.5) or specifications in Standard Methods 9020 B.4.d (Reference 17.2).
Somatic coliphage—Those coliphage that infect host cells via the outer cell membrane but do not
infect host cells via the F-pilus.
April 2001 30
------- |