Of ffca of and EPA*00«-83rt 1 $
Environmental Pro!«ctbn O»v«topmiBnf Juty 1983
Ag«f»ey Washington, OG 204SO
Test Method
Method for the
Determination of
Asbestos in Bulk
Building Materials
-------
1SHEPORT HO.
EPA/600/R-93/116
TECHNICAL REPORT DATA
2.
PB93-218576
4. TITLE MID SUBTITLE
Method tor the Determination of Asbestos in Bulk
Building Materials
TEST METHOD
5.REPORT DATE
6.PERFORMING ORGANIZATION
CODE
7. AUTHOR(S)
R. L. Perkins tnd B. V,. Harvey
8.PERFORMING ORGANIZATION
REPORT NO.
9. PERFORMING ORGANIZATION NAME AND ADDRESS
Research Triangle Institute
P.O.B. 12194
Research Triangle Park, VC 27709-2194
10.PROGRAM ELEMENT NO.
CC6L1A
11. CONTRACT/GRANT HO.
68024550 and 69D10009
12. SPONSORING AGENCY NAME AND ADDRESS
U. S. Environmental Protection Agency
Atmospheric Research and Exposure Assessment Lab
Methods Research and Development Division (MD-77)
Research Triangle Park, NC 27711
13.TYPE Of REPORT AND PERIOD
COVERED
Test Method
14. SPONSORING AGENCY CODE
EPA/600/09
15. SUPPLEMENTARY NOTES
Although this method has been developed as a candidate for compliance monitoring
for EPA programs, it must be officially designated by a program office in their
regulations 'before it can be used for compliance monitoring. Th» user should
verify the official status of the method before using it for compliance monitoring
purposes.
16. ABSTRACT
A method describing 'the qualitative and quantitative analysis of bulk building
materials for-asbestos content is described. The method employs polarised light
microscopy (PLM), x-ray diffraction (XRD), and analytical transmission electron
microscopy (ASM) for qualitative identification of materials. Quantitative
analysis is accomplished by comparison of'gravimetrically prepared standards of
knovn composition with unknown samples using a combination of visual comparison,
point counting, gravimetry and quantitative,x-ray diffraction.
17.
KEY VORDS AND DOCUMENT ANALYSIS
a.
DESCRIPTORS
b.IDENTIFIERS/ OPEN
ENDED TERMS
C.COSATI
18. DISTRIBUTION STATEMENT
Release to Public
19. SECURITY CLASS
fThis Report}
Unclassified . "
21.NO. OF
PAGES.
• 99^
20. SECURITY CLASS
(This
22. PRICE
-------
EPA/600/R-93/116
TEST METHOD
METBOD FOR THE DETERMINATION OF ASBESTOS
IN BULK BUILDING MATERIALS
by
R. L. Perkins and B. W. Harvey
EPA Project Officer
1 Michael E. Beard
Atmospheric Research and Exposure Assessment Laboratory
U.S. Environmental Protection Agency
Research Triangle Park, NC 27709
EPA Contracts Nos. 68024550 and (58D10009
RT1 Project No. 91U:5960-181
'June 1993
y& Printed on Recycled Paper
-------
DISCLAIMER
The information in this document has been funded wholly or in part by the United States
Environmental Protection Agency under Contracts 68-02-4550 and 68D10009 to the Methods
Research and Development Division, Atmospheric Research and Exposure Assessment
Laboratory, Research Triangle Park, North Carolina. It has been subjected to the Agency's
peer and administrative review, and it has been approved for publication as an EPA
document. Mention of trade names or commercial products does not constitute endorsement
or recommendation for use.
-------
TABLE OF CONTENTS
<-
SECTION PAGE
•f,~" ,
1.1 INTRODUCTION T/.V^ ...... , ..... , .......................... I
•1.1 Rcftfthcw*. >.-<;-.% . *.•*•. .-.r.V. ............................ 3
-*' -& fy?^,-?''- -„/
2.1 METHODS &"?*: :.*.'.'. ......> ...... ' ........................... 3
1.1 SlcrtomkroKOpic Ewonlitatioa ....... ........ .................... 3
,; .-.-. v.v. •: . . :-r r ............................... 4
-. 2.1.2 HMqi&fa, v;/. .v':,v; ................................ 4
2. 1.3; Interference. ; /. , . '. .'&£ . '. .............................. 4
2.1.4 Precision and Accuracy ........ ................... . . . 4
2.I.S Procedure* '"..,,'.. .................................. 5
'" 2. 1.5.1' Sample Preparation .'. ......................... 5
2.1.5.2; Analysis . ,_, ....... .................... 6
2.1.6" Calibration Materials ....................... . . S
2.1.7 Refem»«« '". '. ; ...... . ......................... 8
2.2 PoUriwd Ufht Microscopy .............................. 9
' 2.2/1 Principle and Applicability ...... . ...................... 9
•2.2.2 Ranted:. / ..... ........... . ...................... 10
2.2.3 Int*ffe«oc« ."'. /. ............... r .................. 10
2.2.4 Precision and Accuracy ........................... . . . 10
2.2.5 Procedures ................................... 11
2.2.5.1 Sample Preparation ................................ 11
" 2.2.5. 1.1 'Qualitative Analysis Preparation ................ il
' 2.2.5.1.2 Quantitative Analysis Preparation ...... . . . 12
2.2.5.2' Analysis . ; .............................. . 13
* 2.2.5.2.1 Identification . . , .......... ... . ..... 13
'•* 2.2.5.2.2 Quantitation of Asbestos Content .............. . . 16
2.2.5.2.3 Microscope Alignment ..................... . . 22
2.2.6, References, ............... T. ........................ 22
23 .Grarunetry ---- .' .......... ......................... .......... 23
2.3.1 Principle and Applicability .......................... 23
2.3,2 Interferences ............................... . .............. 24
2.3.3 QuantitatioD .- . ., ............................................. 25
2.3.4 Preliminary Examination and Evaluation ............ - .................. 25
2.3.5 Sample Preparation ......... '. .................... -.J . . \ ........ 26
2.3.5.1,, Drying ..'.:, ....................................... 26
2.3.S.2?Homogenization/Grain Size Reduction . . .......... "...." ....... 26
2.3.6 Procedure for Ashing ...... ....................... ' . ' . .'% ..... .' . . 27
2.3.7 Use"of Solvents' for Removal of Organics '. .............................. 28
2.3.8 Pr^aw^for^Acid Dissolution' ............... .... ."/'. .-.-. ....'.. ..... 29
2.3.9 De*ennin«Joo of , Optimal Precision and Accuracy - ......... '^^ . .: .'..:...... 31
, . , 2.3.10 RefereocesV^J-/. V:r- .t*.?t ...... -. ........... -. ..... : .l. I* :..'/...:.' '31
- 2,4 X-IUy Powder Diffraction . . H ?~. .' ........... ...... ".' .................. 32
2.4.1, Principle and Applicability .y'. ............ . : ...... ,..'....' ....... ... 32
2.4*52 Range and Sensitivity ... , .^ ..... ...... .... ^ ..... .". . . ..-.." ....... 35
. :,. . :'.".;?.'. .', ............. ,...'.'. -;. . .*'. 1 :>V. : '.-. >. . ", 35
-------
TABLE OF CONTENTS (cont'd)
SECTION PAGE
' t
2.4.3.1 Interferences . . 35
2.4.3.2 Matrix Effects . . . 38
2.4.3.3 Particle Size Dependence . . .39
2.4.3.4 Preferred Orientation Effects ... .39
2.4.3.S Lack of Suitably Characterized Standard Materials .. . 39
2.4,4 Precision and 'Accuracy .... V . . . . 40
2.4.5 Procedure , . 40
2.4.S.I Sampling . . . . 40
2.4.5.2 Analysis , . . . 40
' 2.4.5.2.1 Sample Preparation . ... 41
2.4.5.2.2 Milling . 41
2.4.5,2.3 AUu'ng 42
2.4.5.2.4 Acid Washing . . 42
2,4.5.3 Qualitative Analysis . . . .42
2.4.5.3.1 Initial Screening of Bulk Material . 42
2.4.5.3.2 Detection of Minor or Trace Constituents . . 43
2.4.5.4 Quantitative Analysis . 44
2.4.6 Calibration . . . . 46
2.4.6.1 Preparation of Calibration Standards . . .46
, 2.4.6.2 Analysis of Calibration Standards . 47
'2.4.7 Calculations 49
2.4.8 References . . . . 51
Analytical Electron Microscopy .... . si
2.5.1 Applicability . . ... 51
2.5.2 Range' . . . ... 52
1.5.3 Interferences . . . 52
2.5.4, Precision and Accuracy . ... . . . . . . 52
2.5.5 Procedures . . . . . .52
2.5.5.1 AEM Specimen Preparation for Semi Quantitative Evaluation 53
2.5.5.2 AEM Specimen Preparation for Quantitative Evaluation . . 54
2.5.5.2.1 Identification . . . . 54
2.5.6 References . 54
2.6 Other Methodologies 53
3.9 QUALITY CONTROL/QUALITY ASSURANCE OPERATIONS- PLM 55
3.1 General Coratdtrations 56
, 3.1.1 T:»iai3g 56
3.1.2 Instrument Calibration and Maintenance ... . . . 56
3d Quality Control of Asbestos Analysis 57
3.2,1 Qualitative Analysis 57
3.2.2 Quantitative Analysis 58
3.3 Interlaboratory Quality Control 59
3.4' Performance Audits 60
3.S Systems Audits ' 60
3.< References 61
-------
TABLE OF CONTENTS (cor.t'd)
APPENDIX A: GLOSSARY OF TERMS
APPENDIX B: APPARATUS FOR SAMPLE PREPARATION AND ANAL'i SIS
APPENDIX C: PREPARATION AND USE OF CALIBRATION STANDARDS FOR BULK ASBESTOS
APPENDIX D: SPECIAL-CASE BUILDING MATERIALS
-------
TABLES
TABLE PAGE
1-1 Simplified Flowchart for Analysis of Bulk Materials . 2
2-1 Suggested Acceptable Errors For PLM Analysis .... 1!
2-2 Optical Properties of Asbestos Fibers . 19
• \
2-3 Typical Central Stop Dispersion Staining Colors 20
2-4 Optical Properties of Man-Made Textile Fibers . 20
2-5 Optical Properties of Selected Fibers . . . . . 21
2-6 The Asbestos Minerals and Their Nonasbestiform Analogs 34
2-7 Principal Lattice Spacings of Asbestiform Minerals . . 34
2-8 Common Constituents in Building Materials . ... .36
2-9 Interferences in XRD Analysis of Asbestitorm Minerals .... 37
-------
1.0 INTRODUCTION
"""- Laboratories are now called upon to identify asbestos in a variety of bulk building
materials, including loose-fill insulations, acoustic and thermal sprays, pipe and boiler wraps,
plasters, paints, flooring products, roofing materials and cementitious products.
The diversity of bulk materials necessitates the use of several different methods of sample
preparation and analysis.- An analysis with a simple stereomicroscope is always followed by
a polarized light microscopic (PLM) analysis. The results of these analyses are generally
sufficient for identification and quantitation of major concentrations of asbestos. However,
during these stereomicroscopic and PLM analyses, it may be found that additional techniques
t
are needed to: 1) attain a positive identification of asbestos; 2) attain a reasonable accuracy
for the quantity of asbestos in the sample; or 3) perform quality assurance activities to
characterize a laboratory's performance. The additional techniques include x-ray diffraction
(XRD), analytical electron microscopy (AEM), and gravimetry, for which there are sections
included in the method. Other techniques will be considered by the Environmental
Protection Agency (EPA) and may be added at some future time. Table 1-1 presents a
simplified flowchart for analysis of bulk materials.
•** * x
This Method for the Determination of Asbestos in Bulk Building Materials outlines the
applicability of the various preparation and analysis methods to the broad spectrum of bulk
building materials now being analyzed.^ This method has been evaluated by the EPA
Atmospheric Research and Exposure Assessment Laboratory (EPA/AREAL) to determine if
it offers improvements to current analytical techniques for building materials.-jThis method
demonstrated a-capability for improving the precision and accuracy of analytical results. It
contains significant revisions to procedures outlined in the Interim Method,1 along with the
addition of several new procedures.CEach technique may reduce or introduce bias, or have
x ~">~-
some effect on the precision of the measurement, therefore results need to be interpreted
judiciously. Data on each technique, especially those new to asbestos analysis, will be
collected over time and carefully evaluated, with resulting recommendations for changes to
the Method to be passed on to the appropriate program office within EPA.
-------
TABLE 1-1.SIMPLIFIED FLOWCHART FOR ANALYSIS OF BULK MATERIALS
Mandatory
STEREOMICROSCOPIC EXAMINATION
Qualitative (classification, fiber ID) and
Quantitative (calibrated volume estimate)
Section 2.1
Mandatory
POLARIZED LIGHT MICROSCOPY
Qualitative (classification, fiber ID) and
Quantitative (calibrated area estimate
and/or point count)
Section 2.2
Continue when problems are encountered with PLM
and/or for Quality Assurance purposes
Qualitative .Problems
(Fiber ID problems)
Quantitative Problems
(?ACM?)
Matrix removal
Section 2.3
PLM
XRD
Sec. 2.4
AEM
Sec. 2.5
Gravimetry XRD
Sec. 2.3 j (Sec. 2.4
XRD
1
AEM
PLM
XRD
AEM
(fiber identification)
(amount of asbestos in residue)
-------
X ^
7 This is,an analytical method. It is not intended to cover bulk material sampling, an area
irV •; i '*,, s , W^ ;} • i ,'
addressed previously2-3-4;* by the EPA.' However, subsampling or sample spli'tmg as it
-
1.1- References ^'C^-' \ , .-
, ' ? . fi.i ,^c^ "J •>>•"' ' ' i
$v k,< i, r - ^c^v-'v > ^ "5-, --
"* 1. Interim Method for the Determination of Asbestos in Bulk Insulation Samples,
;' U.S.-E'.P.A>60C/M4:82-020, 1982.
"''- 2. Asbestos-Containing Materials in School Buildings: A Guidance Document, Pan
1'and 2..U.S. E.P.A./O.T.S NO. C00090, 1979.
"• ' ** / ' i f
;, 3. Asbestos in Buildings: Simplified Sampling Scheme for Friable Surfacing
! * ,Matcrlals,iU.S: E.P.A. 560/5-85 -030a, 1985.
, -f%
4. Guidance for Controlling Asbestos-Containing Materials in Buildings, U S
E.P. A.V 560/5-85-024, 1985.
5. Asbestos-Containing Materials in Schools: Final Rule and Notice, 40 CFR Part
' , \ 763, October, 1987.
% .
2,0 METHODS
2.1 Stcreomicroscopic Examination
* •#
A preliminary visual examination using a simple stereomicroscope is mandatory for all
samples. A sample should be of sufficient size to provide for an adequate examination For
many samples, observations on homogeneity, preliminary fiber identification and serm-
quantitation of constituents can be made at this point. Another method of identification and
semi-quantitation of asbestos must be used in conjunction with the stereomicroscopic
examination. A description of the suggested apparatus needed for stereomicroscopic
examination is given in Appendix B.
The laboratory should note any samples of insufficient volume A sufficient sample
;
volume is sample-type dependent. For samples such as floor tiles, roofing felts, paper
insulation, etc., three to four square inches of the layered material would be a preferred
sample size. For materials such as ceiling tiles, loose-fill insulation, pipe insulation, etc , a
,- ^ ~ ry -, '
sample size of approximately one cubic inch (~ 15cc) would be preferred. For samples of
thin-coating materials such as paints, mastics, spray plasters, tapes, etc., a smaller sample
-------
size may be suitable for analysis. Generally, samples of insufficient volume should be
rejected, and further analysis curtailed until the client is contacted. The quantity of sample
affects the sensitivity of the analysis and reliability of the quantitation steps. If there is a
question whether the sample is representative due to mhomogeneity, the sample should be
rejected, at least until contacting the client to see if: 1) the client can provide more material
or 2) the client wishes the laboratory to go ahead with the analysis, but with the lal'oratory
including a statement on the limited sensitivity and reliability of quantitation. If the latter is
the case, che report of analysis should state that the client was contacted, that the client
decided that the lab should use less material than recommended by the method, and t^-at the
client acknowledges that this may have limited the sensitivity and quantitation of the method.
At the time the client is contacted about the material, he or she should be informed that a
statement reflecting these facts will be placed in the report.
2.1.1 Applicability
Stereomicroscopic analysis is applicable to all samples, although its use with vinyl floor
tile, asphaltic products, etc., may be limited because of small asbestos fiber size and/or the
presenllptf interfering components. It does not provide positive identification of asbestos.
2.1.2 Range
Asbestos may be detected at concentrations less than one percent by volume, but this
detection is highly material dependent.
2.1.3 Interferences
Detection of possible asbestos fibers may be made more difficult by the presence of other
•
nonasbestos fibrous components such as cellulose, fiber glass, etc., by binder/matrix
materials which may mask or obscure fibrous components, and/or by exposure to conditions
(acid erivi|pj?ment, high temperature, etc.) capable of altering or transforming asbestos.
••• 'i.'
2.1.4 Precision and Accuracy
The precision and accuracy of these estimations are material dependent and must be
determined by the individual laboratory for the percent range involved. These values may be
-------
determined for an individual analyst by the in-house preparation and analysis of standards
and the use of error bars, control charts, etc.
The labs should also compare to National Voluntary Laboratory Accreditation Program
(NVLAP) proficiency testing samples, if the lab participates in the Bulk Asbestos NVLAP,
or to external quality assurance system consensus results such as from proficiency testing
programs using characterized materials. However, at this time, consensus values for the
quantity of asbestos- have beer, shown to be unreliable. Only proficiency testing materials
characterized by multiple techniques should be used to determine accuracy and precision.
2.1.5 Procedures
NOTE: Exposure to airborne asbestos fibers is a health hazard. Bulk samples
submitted for analysis are oftentimes friable and may release fibers during handling or
matrix reduction-steps. AH sample handling and examination must be carried out in a
HEP A-filtered hood, a class 1 biohazard hood or a glove box with continuous airilow
(negative pressure). Handling of samples without these precautions may result in
exposure of the analyst to and contamination of samples by airborne fibers.
•
2.1.5.1 Sample Preparation
No sample preparation should be undertaken before initial stereomicroscopic examination.
Distinct changes in texture or color on a stereomicroscopic scale that might denote an uneven
distribution of components should be noted. When a sample consists of two or more distinct
layers or building materials, each should be treated as a separate sample, when possible.
Thin coatings of paint, rust, mastic, etc., that cannot be separated from the sample without
compromising the layer are an exception to this case and may be included with the layer to
which they are attached. Drying (by heat lamp, warm plate, etc.) of wet or damp samples is
recommended before further stereomicroscopic examination and is mandatory before PLM
examination. Drying must be done in a safety hood.
For nonlayered materials that are heterogeneous, homogenization by some means (mill,
blender, mortar and pestle) may provide a more even distribution of sample components. It
-------
may also facilitate disaggregation of clumps and removal of binder from fibers (rarely
however, it may mask fibers that were originally discernable).
For materials such as cementitious products and floor tiles, breaking, pulverizing, or
grinding may improve the likelihood of exposing fibrous components.
It may be appropriate to treat some materials by dissolution with hydrochloric acid to
remove binder/matrix materials. Components such as calcite, gypsum, magnesite, etc , may
be removed by this method. For materials found to possess a high organic content
(cellulose, organic binders), ashing by means of a muffle furnace or plasma asher (for small,
cellulosic samples), or dissolution by solvents may be used to remove interfering material.
In either case, it is recommended that matrix removal be tracked gravimetrically.
Additional information concerning homogenization, ashing and acid dissolution may be
found in Sections 2.2.5.1 and 2.3.
2.1.5.2 Analysis
f
Samples should be examined with a simple stereomicroscope by viewing multiple fields
of view over the entire sample. The whole sample should be observed after placement in a
suitable container (watchglass, weigh boat, etc.") substrate. Samples that are very large
should be subsampled. The sample should be probed, by turning pieces over and breaking
open large clumps. The purpose of the stereomicroscopic analysis is to determine
homogeneity, texture, friability, color, and the extent of fibrous components of the sample.
This information should then be used as a guide to the selection of further, more definitive
qualitative and quantitative asbestos analysis methods. Homogeneity refers to whether each
subsample made for other analytical techniques (e.g. the "pinch" mount used for the PLM
analysis), is likely to be similar or dissimilar. Color can be used to help determine
homogeneity, whether the sample has become wet (rust color), and to help identify or clarify
sample labelling confusion between the building material sampler and the laboratory.
Texture refers to size, shape and arrangement of sample components. Friability may be
indicated by the ease with which the sample is disaggregated (see definitions in Appendix A)
as received by the analyst. This does not necessarily represent the friability of the material
as determined by the assessor at the collection site. The relative proportion of fibrous
-------
components to binder/matrix material may be determined by comparison to similar materials
of known fibrous content. For materials composed of distinct layers or two or more distinct
building materials, each layer or distinct building material should be treated as a discrete
sample. The relative proportion of each in the sample should be recorded. The layers or
materials should then be separated and analyzed individually. Analysis results for each layer
or distinct building material should be reported. If monitoring requirements call for one
reported value, the results for the individual layers or materials should always be reported
along with the combined value. Each layer or material should be checked for homogeneity
during the stereomicroscopic analysis to determine the extent of sample preparation and
homogehization necessary for successful PLM or other analysis Fibers and other
components should be removed for further qualitative PLM examination.
Using the information from the stereomicroscopic examination, selection of additional
preparation and analytical proceduies should be made. Stereomicroscopic examination
should typically be performed again after any change or major preparation (ashing, acid
dissolution, milling, etc.) to the sample. Stereomicroscopic examination for estimation of
asbestos content may also be performed again after the qualitative techniques have clarified
the identities cf the various fibrous components to assist in resolving differences between the
initial quantitative estimates made during the stereomicroscopic analysis and those of
subsequent techniques. Calibration of analysts by use of materials of known asbestos content
•
is essential.
The'stereomicroscopic examination is often an iterative process. Initial examination and
estimates :»f asbestos concentration should be made. The sample should then be analyzed by
PLM and possibly other techniques. These results should be compared to the initial
stereomicroscopic results. Where necessary, disagreements between results of the techniques
should be resolved by reanalyzing the sample stereomicroscopically.
-------
2.1.6 Calibration Materials
Calibration materials fall into several categories, including internal laboratory standards
and other materials that have known asbestos weight percent content. These calibration
materials could include:
• Actual bulk samples: asbestos-containing materials that have been characterized by
other analytical methods such as XRD, AEM and/or gravimetry. (e.g. NVLAP test
samples).
•
• Generated samples: in-house standards that can be prepared by mixing known
quantities of asbestos and known quantities of asbestos-free matrix materials (by
weight), and mixing (using blender, mill, etc.) thoroughly to achieve homogeneity;
matrix materials such as vermiculite, perlite, sand, fiberglass, calcium carbonate,
etc. may be used. A range of asbestos concentrations should be prepared (e.g. 1, 3,
5, 10, 20%, etc.). The relationship between specific gravities of the components
used in standards should be considered so that weight/volume relationships may be
determined.
• Photographs, drawings: photomicrographs of standards, computer-generated
drawings, etc.
Suggested techniques for the preparation and use of in-house calibration standards are
presented in Appendix C, and at greater length by Harvey et al.' The use of synthesized
standards for analyst calibration and internal laboratory quality control is not new however,
having bee.n outlined by Webber et al.2 in 1982.
•?
2.1.7 References
»
1. Harvey, B. W., R. L. Perkins, J. G. Nickerson, A. J. Newland and M. E. Beard,
'"Formulating Bulk Asbestos Standards", Asbestos Issues, April 1991, pp. 22-29.
< •
2. "Webber, J. S., A. Pupons and J. M. Fleser, "Quality-Control Testing for Asbestos
Analysis with Synthetic Bulk Materials". American Industrial Hygiene Associations
Journal, 43, 1982, pp. 427-431.
-------
2.2 Polarized Light Microscopy
2.2.1 Principle and Applicability
Samples of buik building materials taken for asbestos identification should first be
examined with the simple stereomicroscope to determine homogeneity and preliminary fiber
identification. Subsamples should then be examined using PLM to determine optical
properties of constituents and to provide positive identification of suspect fibers.
The principles of optical mineralogy are well-established.12J-4 A light microscope
equipped with two polarizing filters is used to observe specific optical characteristics of a
•
sample. The use of plane polarized light allows for the determination of refractive indices
relative to specific crystallographic orientations. Morphology and color are also observed
while viewing under plane polarized light. Observation of particles or fibers while oriented
between polarizing filters whose privileged vibration directions are perpendicular (crossed
polars) allows for determination of isotropism/anisotropism, extinction characteristics of
anisotropic particles, and calculation of birefringence. A retardation plate may be placed in
the polarized light-path for verification of the sign of elongation. If subsamples are prepared
in such a way as to represent all sample components and not just suspect fibers, semi-
quantitative analysis may also be performed. Semi-quantitative analysis involves the use of
calibrated visual area estimation and/or point counting. Visual area estimation is a semi-
quantitative method-that must relate back to calibration materials. Point counting, also semi-
quantitative, is a standard technique used in petrography for determining the relative areas
occupied by separate minerals in thin sections of rock. Background information on the use
of point counting3 and the interpretation of point count data5 is available.
Although PLM analysis is the primary technique used for asbestos determination, it can
show significant bias leading to false negatives and false positives for certain types of
materials. PLM is limited by the visibility of the asbestos fibers. In some samples the fibers
may be'reduced to a diameter so small or masked by coatings to such an extent that they
cannot^e reliably observed or identified using PLM.
-------
2.2.2 Range
The detection limit for visual estimation is a function of the quantity of sample analyzed,
the nature of matrix interference, sample preparation, and fiber size and distribution.
Asbestos may be detected in concentrations of less than one percent by area if sufficient
material is analyzed. Since floor tiles may contain fibers too small to be resolved by PLM
(< 0.25 /xm in diameter), detection of those fibers by this method may not be possible.
When point counting is used, the detection limit is directly proportional to the amount of
sample analyzed, but is also limited by fiber visibility. Quantitation by area estimation, both
visual and by point counting, should yield similar results if based on calibration standards. "
2.2.3 Interferences
Fibrous and nonfibrous, organic and inorganic constituents of bulk samples may interfere
with the identification and quantitation of the asbestos mineral content. Binder/matrix
materials may coat fibers, affect color, or obscure optical characteristics to the extent of
masking fiber identity. Many organic mastics are soluble in refractive index liquids and,
unless removed prior to PLM examination, may affect the refractive index measurement of
constituent materials. Fine particles of other materials may also adhere to fibers to an extent
sufficient to cause confusion in identification. Gravimetric procedures for the removal of
interfering materials are presented in Section 2.3.
2.2.4 Precision and Accuracy
Data obtained for samples containing a single asbestos type in a sample matrix have been
reported previously by Brantley et al.6 Data for establishing the accuracy and precision of
the method for samples with various matrices have iv-~.,ntly become available. Perkins,7
Webber et al.8 and Harvey et al.9 have each documented the tendency for visual estimates
to be high when compared to point-count data. Precision and accuracy must be determined
by the individual laboratory for the percent range involved. If point counting and/or visual
estimates are used, a table of reasonably expanded errors, such as those shown in Table 2-1,
should be generated for different concentrations of asbestos.
10
-------
If the laboratory cannot demonstrate adequate precision and accuracy (documented by
control charts, etc), quantitation by additional methods, such as gravimetry, may be required.
Refer to the Handbook for SRM Users10 for additional information concerning the concepts
of precision and accuracy.
TABLE 2-1. SUGGESTED ACCEPTABLE ERRORS FOR PLM ANALYSIS
(Based on 400 point counts of a reasonably homogeneous sample
or 100 fields of view for visual estimate)
% Area Asbestos
1
5
10
20
30
40
Acceptable Mean
Result
>0-3%
>l-9%
5-15%
10-30%
20-40%
30-50%
% Area Asbestos
50
60
70
80
90
100
Acceptable Mean
Result
40-60%
JO-70%
60-80%
70-90%
80-100%
90-100%
2.2.5 Procedures
NOTE: Exposure to airborne asbestos fibers is a health hazard. Bulk samples
submitted for analysis are oftentimes friable and may release fibers during handling or
matrix reduction steps. All sample and slide preparations must be carried out in a
HEPA-filtered, a class 1 biohazard hood, or a glove box with continuous airflow
(negative pressure). Handling of samples without these precautions may result in
exposure of the analyst to and contamination of samples by airborne fibers.
2.2.5.1 Sample Preparation
Slide mounts are prepared for the identification and quantitation of asbestos in the
sample.
2.2.5.1.1 Qualitative Analysis Preparation
-i
The qualitative preparation must allow the PLM analysis to classify the fibrous
components of the sample as asbestos or nonasbestos. The major goal of the qualitative
11
-------
preparation is to mount easily visible fibers in appropriate refractive index liquids for
complete optical characterization. Often this can be accomplished by making immersion
grain mounts of random subsamples of the homogeneous material. Immersion liquids with
refractive indices close to the suspected (see stereomicroscopic analysis) asbestos mineral
should be used for the qualitative analysis so that nD can be determined Problem samples
include those with inhomogeneities, coatings, small fibers, and interfering compounds.
Additional qualitative preparations are often necessary for these types of samples. All
samples, but especially those lacking homogeneity, may require picking of fibers from
specific sample areas during the stereomicroscopic examination. Coatings on the fibers often
need to be removed by mechanical or chemical means. Teasing the particles apart or use of
a mortar and pestle or similar mechanical method often is sufficient to free f;bers from
coatings. Chemical means of removing some coatings and interfering compounds are
discussed in Section 2.3, Gravimetry.
2.2.5.1.2 Quantitative Analysis Preparation
The major purpose of the quantitative preparation is to provide the analyst with a
representative grairi mount of the sample in which the asbestos can be observed and
distinguished from the nonasbestos matrix. This is typically performed by using randomly
selected subsamples from a homogeneous sample (see stereomicroscopic analysis). Particles
should be mounted in a refractive index (Rl) liquid that allows the asbestos to be visible and
distinguished from nonasbestos components. Care should be taken to ensure proper loading
and even distribution of particles. Both the qualitative and quantitative sample preparations
are often iterative processes. Initial samples are prepared and analyzed. The PLM analysis
may disclose problems or raise questions that can only be resolved by further preparations
(e.g. through the use of different RI immersion liquids, elimination of interfering
compounds, sample homogenization, etc.)
9 ,
ForTayered materials, subsamples should be taken from each individual or discrete layer.
Each of these subsamples should be treated as a discrete sample, but as stated in Section
2.1.5.2, the results for the individual layers or materials may be combined if called for by
monitoring requirements.
i
*
12
-------
Homogenization involves the use of any of a variety of devices, such as a mortar and
pestle, mill, or blender to pulverize, disaggregate and mix heterogeneous, friable bulk
materials. Selection of the appropriate device is dependent upon personal preference and the
nature of the materials encountered. A blender or mortar and pestle may be adequate for
homogenizing materials that lack appreciable amounts of tacky matrix/binder, and for
separating interfering components from the fibers. For materials which are unusually sticky
or tacky, or contain unusually long asbestos fibers, milling (especially freezer milling) may
be more efficient. However, milling should be discontinued as soon as the material being
milled appears homogeneous, in order to reduce the potential for mechanically reducing fiber
size below the resolving power of the polarizing microscope. Hammer mills or cutting mills
may also be used on these materials; however, the same precaution regarding reduction of
fiber size should be taken. Blending /milling devices should be disassembled (to the extent
possible) and thoroughly cleaned after each use to minimize contamination.
2.2.5.2 Analysis
Analysis of bulk building materials consists of the identification and semi-quantitation of
the asbestos type(s) present, along with the identification, where possible, of fibrous
nonasbestos materials, mineral components and matrix materials. If the sample is
heterogeneous due to the presence of discrete layers or two or more distinct building
materials, each layer or distinct material should be analyzed, and results reported. Total
asbestos content may also be stated in terms of a relative percentage of the total sample.
2.2.5.2.1 Identification
Positive identification of asbestos requires the determination of the following optical
properties:
• Morphology • Birefringence
• Color and, if present, pleochroism • Extinction characteristics
• Refractive indices (± .005) • Sign of elongation
13
-------
Descriptions of the optical properties listed above for asbestos fibers may be found in
Appendix A. Glossary of Terms. Table 2-2 lists the above properties for the six types of
asbestos and Table 2-3 presents the central stop dispersion staining colors for the asbestos
minerals with selected high-dispersion index liquids. Tables 2-4 and 2-5 list selected optical
properties of several mineral and man-made fibers. All fibrous materials in amounts greater
than trace should be identified as asbestos or nonasbestos, with all optical properties
measured for asbestos and at least one optical property measured for each nonasbestos
fibrous component that will distinguish each from asbestos. Small fiber size and/or binder
may necessitate viewing the sample at higher magnification (400-500x) than routinely used
(lOOx).
Although it is not the purpose of this section to explain the principles of optical
mineralogy, some discussion of the determination of refractive indices is warranted due to its
importance to the proper identification of the asbestos minerals. Following is a brief
discussion of refractive index determination for the asbestos minerals.
All asbestos minerals are anisotropic, meaning that they exhibit different optical
properties (including indices of refraction) in different directions. All asbestos minerals are
biaxial, meaning that they have one principal refractive index parallel (or nearly parallel) to
the length of the fiber and two principal refractive indices (plus all intermediate indices
between these two) in the plane perpendicular (or nearly so) to the length of the fiber.
Although chrysotile (serpentine) is classified as a biaxial mineral, it behaves as a uniaxial
mineral (two principal refractive indices) due to its scrolled structure. Amosite and
crocidolite, although also biaxial, exhibit uniaxial properties due to twinning of the crystal
structure and/or random orientation of fibrils in a bundle around the long axis of the bundle.
For all of the asbestos minerals except crocidolite, the highest refractive index (7) is aligned
with the fiber length (positive sign of elongation). For crocidolite, the lowest refractive
index (a) is aligned with the fiber length (negative sign of elongation). A more complete
explanation of the relationship of refractive indices to the crystallographic directions of the
asbestos minerals may be found in References 1, 2, 4, 11 and 12. It should be noted that for
the measurement of refractive indices in an anisotropic particle (e.g. asbestos fibers), the
orientation of the particle is quite critical. Orientation with respect to rotatiojn about the axis
14
-------
of the microscope (and thus with respect to the vibration directions of the polarizer and
analyzer) and also to the horizontal plane (plane of the microscope stage) will affect the
determination of the correct values for refractive indices. The refractive index that is
measured will always correspond to a direction perpendicular to the axis of the microscope
(i.e., lying in the plane of the stage) and is the direction in that horizontal plane parallel to
the vibration direction of the polarizer, by convention E-W.
To determine 7(n ||) for chrysotile, anthophyllite and amosite, the index is measured
when the length of the fiber is aligned parallel to the vibration direction of the polarizer (E-
W). Under crossed polars, the fiber should be at extinction in this orientation. To
determine the lowest refractive index, a (n 1), for chrysotile and amosite, the fiber should
be oriented N-S (extinction position under crossed polars) The determination of n || and n 1
with crocidolite is accomplished in the same manner as with amosite and chrysotile with the
exception that the ay and 7 directions are reversed. For crocidolite, a is measured at the E-
W position (parallel to the polarizer) and 7 is measured at the N-S orientation (perpendicular
to the polarizer). For anthophyllite, the fiber should be oriented N-S and the lowest and
highest indices for this orientation should be measured. These correspond to a and /3
respectively.
The extinction behavior of tremolite-actinolite is anomalous compared to that of most
monocliryc minerals due to the orientation of the optic axes relative to the crystallographic
axes. This relationship is such that the refractive indices of the principal axes a and 7 are
not measured when the fiber is exhibiting the maximum extinction angle. The values
measured at these positions are a' and y. The fiber exhibits an extinction angle within a few
degrees of the maximum throughout most of its rotation. A wide range of refractive indices
from a' to a, and from V to 7, are observed. For tremolite-actmolite, /? is measured on
those fibers displaying parallel extinction when oriented in the N-S position. The refractive
index for a is also measured when the fiber is oriented generally in the N-S position and
exhibits the true extinction angle; true a will be the minimum index. To determine the
refractive index for 7, the fibers should be oriented E-W and exhibit the true extinction
angle; true 7 will be the maximum value for this orientation.
15
-------
When viewing single fibers, the analyst may often be able to manipulate the microscope
slide cover slip and "roll" the fibers to positions that facilitate measuring the true values of
refractive indices. When viewing a large population of fibers with the microscope in the
dispersion staining mode, the analyst can easily detect fibers that exhibit the highest and
lowest indices (j3 and a) in the N-S position and the highest indices (7) in the E-W position.
Since individual asbestos fibrils cannot generally be resolved using polarized light
microscopy, refractive indices are most commonly measured on fiber bundles. Such
measurements would not result in true values for the indices and therefore by convention
should be reported as or' and •/.
Asbestos types chrysotile, amosite and crocidolite are currently available as SRM 1866
and actmolite, tremolite and anthophyllite as SRM 1867 from the Office of Standard
Reference Materials, National Institute of Standards and Technology.
2.2.5.2.2 Quantitation of Asbestos Content
As described in Sections 2.1.5 and 2.1.6, a calibrated visual volume estimation of the
relative concentrations of asbestos and nonasbestos components should be made during the
stereomicroscopic examination. In addition, quantitation of asbestos content should be
performed on subsample slide mounts using calibrated visual area estimates and/or a point
counting procedure. Section 2.1.6 and Appendix C discuss the procedures for preparation
and use of calibration standards. After thorough PLM analysis in which the asbestos and
other components of the bulk material are identified, several slides should be carefully
prepared from randomly selected subsamples. If the sample is not homogeneous, some
homogenization procedure should be performed to ensure that slide preparations made from
small pinch samples are representative of the total sample. Homogenization may range from
•
gentle mixing using a mortar and pestle to a brief period of mixing using a blender equipped
with a mini-sample container. The homogenization should be of short duration (—15
seconds) "if using the blender technique so as to preclude a significant reduction in fiber size.
The use of large cover slips (22x30mm) allows for large subsamples to be analyzed. Each
slide should be checked to ensure that the subsample is representative, uniformly dispersed,
and loaded in a way so as not to be dominated by superimposed (overlapping) particles.
16
-------
During the qualitative analysis of the sample, the analyst should decide on the appropriate
optical system (including magnification) to maximize the \ isibility of the asbestos in the
sample while still allowing the asbestos to be uniquely distinguished from the matrix
' materials. The'analyst may choose to alter the mounting medium or the optical system to
enhance contrast. During the quantitative analysis, slides should be scanned using an optical
setup that yields the best visibility of the asbestos. Upon finding asbestos, the parameters
that were selected in the qualitative analysis for uniquely distinguishing it from the matrix
should be-used for identification. These properties will vary with the sample but include any
or all of the parameters, required for the qualitative analysis. For instance, low magnification
allows for concurrent use of dispersion staining (focal screening), but compromises resolution
of extremely small diameter fibers; use of a compensator plate and crossed polarizers
frequently enhances the contrast between asbestos fibers and matrix material.
Visual area estimates should be made by comparison of the sample to calibration
materials that have similar textures and fiber abundance (see Section 2.1.6 and Appendix C).
A minimum of three slide mounts should be examined to determine the asbestos content by
; visual area estimation. Each slide should be scanned in its entirety and the relative
proportions of asbestos and nonasbestos noted. It is suggested that the ratio of asbestos to
nonasbestos•material be recorded for several fields for each slide and the results be compared
to data derived from the analysis of calibration materials having similar textures and asbestos
content.
For point counting, an ocular reticle (cross-line or point array) should be used to visually
superimpose a point or points on the microscope field of view. The cross-line reticle is
preferred. Its use requires the scanning of most, if not all, of the slide area, thereby
minimizing bias that might result from lack of homogeneity in the slide preparation. In
conjunction with this reticle, a click-stop counting stage can be used to preclude introducing
bias during slide advancement. Magnification used will be dictated by fiber visibility. The
slide should be examined along multiple parallel traverses that adequately cover the sample
area. The analyst should score (count) only points directly over occupied (nonempty) areas.
Empty points should no; be scored on the basis of the closest particle. If an asbestos fioer
and a nonasbestos particle overlap so that a point is superimposed on their visual1 intersection,
17
-------
a point should be scored for both categories. If the point(s) is/are superimposed on an area
which has several overlapping particles, the slide should be moved to another field. Whilr
not including them in the total asbestos points counted, the analyst should record the presence
of any asbestos detected but not lying under the reticle cross-line or array points A
minimum of 400 counts (maximum of eight slides with 50 counts each to minimum of two
slides with 200 counts each) per sample is suggested, but it should be noted that accuracy
and precision improve with number of counts. Point counting provides a determination of
the projected area .percent asbestos. Conversion of are^. percent to dry weight percent is not
feasible unless the specific gravities and relative volumes of the different materials are
known. It should be noted that the total amount of material to be analyzed is dependent on
the asbestos concentration, i.e. the lower the concentration of asbestos, the larger the amount
of sample that should be analyzed, in both trie visual estimation and point counting methods.
Quantitation by either method is made more difficult oy low asbestos concentration, small
fiber size, and presence of interfering materials.
It, is'suggested that asbestos concentration be reported as volume percent, weight percent
*,,
or area'percent depending on the method of quantitation used. A weight concentration
cannot be determined without knowing the relative specific gravities and volumes of the
sample componems.
18
-------
TABLE 2-2. OPTICAL P. ARTIES OF ASBESTOS FIBERS
Mineral
Chrysolite
(asbestiform
serpentine)
AmosrtJ ' •
(asbestiform
grunente)
Crocidolite
(asbestiform
n'ebeck'rte)
Anthophyllite-
asbestos
Tremolite-
Actinolite-
asbestos
Morphology and Color'
Wavy jibers.. Fiber bundles have splayed
ends and "kinks". Aspect ratio typically
>1'0:1. Colorless3
Straight to curved, rigid fibers.
Aspect ratio typically >10 1.
Colorless to brown, nonpleochroic or weakly
so.4 Opaque inclusions may be present
Straight to curved, rigid fibers. Aspect ratio
typically > 10:1. Thick fibers and bundles
common, blue to dark-blue in color.
Pleochroic.
Straight to curved fibers and bundles.
Aspect ratio typically > 1 0.1 . Anthophyllite
cleavage fragments may be present with
aspect ratios <10:1. Colorless to light
brown.
Straight to curved fibers and bundles.
Aspect ratio typically > 10.1. Cleavage
fragments may be present with aspect ratios
<10:1. Colorless to paie green
Refractive Indices'
YS
1.493-1. 546' 1. 517-1.557"
1.532-1.549 '1.545-1.555*
1.529-1.559 1 537-1.567 •
1.544-1.553 1.552-1.561
1.657-1,663 1 699-1 717
1.663-1.686 1 696-1 729
1.663-1.686 1 696-1 729
1.676-1.683 1.697-1.704
1.693 1.697
1.654-1.701 1.668-1.717
1.680-1.698 1.685-1 706
1 598-1.652 1.623-1 676
1.596-1.694 1.615-1.722
1.598-1.674 1.615-1 697
1 61 487 1 63627
Trsmolile
1.600-1.628 1 625-1 655
1.b04-1.612 1 627-1 635
1.599-1.612 1 625-1 637
1.60637 1.63437
Actinolite
1.600-1.628 1.625-1655
1.612-1.668 1.635-1.688
1 613-1 628 1.638-1 655
1 61267 1 63937
Birefringence*
, *
0.004-0.017
J ' •
*
0.021-0054 .
0 003-0 022
0013-0.028
0017-0.028
0.017-0.028
Extinction
Parallel
Usually
parallel
Usually
parallel
Parallel
Parallel and
oblique (up to
21°); Composite
fibers show
parallel extinction
Sign of Elongation
+
(length slow)
+
(length slow)
(length fast)
+
(length slow)
+
(length slow)
1Co!crs died are seen by observation with plane polarized light.
*From references 2,1 *, 12, and 18, respectively. Refractive indices for n, at 589 3nm
'Fibers subjected to heating may be brownish, (references 13,14, and 15)
'Fibers subjected to heating may be dark brown and pleochroic (references 13, H, and 15)
5| to fiber length, except 1 to fiber length for crocidolite only
'Maximum and minimum values from references 2,11.12, and 18 given
7± 0 0007
-------
TABLE 2-3. TYPICAL CENTRAL STOP DISPERSION STAINING COLORS'
Mineral
Chrysotile
Amosite
Croctdolite
Anthophylhte-
asbestos
Tremolite-
asbestos
Actmohte-
asbestos
Cargille*
RI Liquid
! 550HD
1 680
1.680
1.605HD
1 6Q5HD
1 605HD
1.630HD
"1
Magenta to light blue-green
XQ\ M 520-620nm
Yellow to magenta
Vs ca 420-520nm
Yellow to magenta
XQ'S ca 420-520nm
Pale yellow to yellow
Vs ca 330-430nm
Pale yellow to yellow
Vs ca 330-430nm
Pale yellow
V> ca 260-360nm
Yellow to magenta
Vs ca 420-520nm
nl
Blue-green to pale blue
V* « 600-700nm
Blue magenta to light blue
Vs ca 560-660nm
Pale yellow to golden yellow
Vs ca 360-460nm
Golden yellow to light blue green
V*> ca 460-700nm
Golden yellow to light blue green
V*- c"» 460-700nm
Pate sellow to golden yellow
V1- ca 360-460nm
Golden yellow to blue
Vs ca 450-600nm
'Modified from reference 16
TABLE 2-4. OPTICAL PROPERTIES OF MAN-MADE TEXTILE FIBERS':
Fiber Type
Polyester (Dacron5*)
Polyamide (Nylon*)
Aramid (Kevlar")
Olefin (Polyethylene)
Olefin (Polypropylene)
Viscose Rayon
Acetate
Acrylic (Orion®)
Modacryhc (Dynel*)
nil
1 710
1 582
= 2 37
! 556
1 520
1.535-1.555
1.478-1 480
1.505-1.515
1.535
nl
1 535
1 514
= 1 641
1.512
1.495
1.515-1.535
1 473-1 476
1 507-1 517
I 532
n || - n ±
0 175
0063
0 729
0044
0025
0020
0.004-0 005
0.004-0 002
0002
1
Sign of
Elongation
+
+
+
+
+
+
+
-
+
'Modified from reference 17
;Refractive indices for specific fibers; other fibers ma> vary
20
-------
TABLE 2-5.' OPTICAL PROPERTIES OF SELECTED FIBERS'
FIBER
TYPE
Paper (Cellulose)
Olefin
(polyethylene)
Brucite (nemali(e)
Heated amosite
Glass fibers,
Mineral wool
Wollastonite
Fibrous laic
MORPHOLOGY
Tapered, flat ribbons
Fill menu or shredded
like chrysolite
Straight fibers
Similar to unheated,
(brittle and shorter)
pleoohroic n | -dark brown
nj_ yellow
Exodt. shapes, (ear drops.
single filaments
Straight needles and blades
Thin ilcavage nbbons and
wavy fibers
REFRACTIVE
INDICES
nj - 1 580
n 1 - 1 530
nj - 1 556
ni - 1 512
n| - 1 560-1 590
nJ. - 1 580-1 600
n|| and nl >l 7001
1 515-1 700
r>! - 1 630
ni ~ \ 63?
n JL alui 1 610
n|| - 1 60
nj. - I 54
BIREFRINGENCE
(n| -nl)
High (0 05)
Moderate (0 044)
Moderate
(0012-0020)
High(> 0 05)
Uolrop'C
Moderate to low
(0018 to 0002)
High (0 06)
EXTINCTION
ANGLE
Parallel and
incomplete
Parallel
Usually parallel
Usually parallel
Parallel and oblique
Parallel and oblique
SIGN OF
ELONGATION-
» '
•+•
+•
occasionally +
+
+ and -
+
DISPERSION STAINING
COLORS
in 1 550HD
n | • yellow
(V» < 400nm)
n J. : pale blue
(V > 700nm)
in 1 550HD
n | • yellow to magenta
(V» = 440-540nm)
n 1 pale blue
(V > 700nm)
in 1 550HD
n| golden ye How
(V» 440-460nm)
n X yellow
(Vs 400-440nm)
in 1 680HD
n | & n 1 both pale
yellow 10 unite
(Vs < 400nm)
in 1 550HD
usually pale blue to blue
( Vi 5*0 to > 700nm)
in 1 605HD
n| &. n 1 yellow to pale
yellow
(\,\ < -160nn\)
in 1 550HD
n J pale \ellow
(\, s <400nm)
n 1 pale blue
(\,'s >660nm)
'From reference 19
'From references 13. 14 and 15
-------
2.2.5.2.3 Microscope Alignment
In order to accurately measure the required optical properties, a properly aligned
polarized light microscope must be utilized. The microscope is aligned when-
1) the privileged directions of the substage polarizer and the analyzer are at 90° to one
another and are represented by the ocular cross-lines;
2) the compensator plate's privileged vibration directions are 45° to the privileged
directions of the polarizer and analyzer;
3) the objectives are centered with respect to stage rotation; and,
4) the substage condenser and iris diaphragm are centered in the optic axis
Additionally, the accurate measurement of the refractive index of a substance requires the
use of calibrated refractive index liquids. These liquids should be calibrated regularly to an
accuracy of 0.004, with a temperature accuracy of 2°C using a refractometer or R.I. glass
beads.
2.2.6 References
i-
1. Bloss, F. Donald, An Introduction to the Methods of Optical Crystallography,
Philadelphia: Saunders College Publishing, 1989.
2. Kerr, Paul F., Optical Mineralogy, 4th Edition, New York: McGraw Hill, 1977.
3. Chamot, £. M. and C. W. Mason, Handbook of Chemical Microscopy, Volume
One, 3rd edition, New York: John Wiley & Sons, 1958.
4. Ehlers, Ernest G., Optical Mineralogy, Vols. 1 and 2, Palo Alto, CA: Blackwell
Scientific Publications, 1987.
5. Chayes, F., Petrographic Modal Analysis: An Elementary Statistical Appraisal,
New York: John Wiley & Sons, 1956.
6. Brantley, E. P., Jr., K. W. Gold, L. E. Myers, and D. E. Lentzen, Bulk Sample
Analysis for Asbestos Content: Evaluation of the Tentative Method, EPA-
600/S4-82-021, 1982.
7. Perkins, R.L., "Point-Counting Technique for Friable Asbestos-Containing
Materials", The Microscope, 38, 1990, pp.29-39.
22
-------
8. Webber, J.S., R. J. Janulis, L. J. Carhart and M.B. Gillespie, "QuantiUtmg
Asbestos Content in Friable Bulk Samples: Development of a Stratified Point-
Counting Method", American Industrial Hygiene Association Journal, 51, 1990,
pp. 447-452.
9. Harvey, B. W., R. L. Perkins, J. G. Nickerson, A. J. Newland and M. E. Beard,
"Formulating Bulk Asbestos Standards", Asbestos Issues, April 1991, pp. 22-29
10. Handbook for SRM Users, N1ST (formerly NBS) Special Publication 260-100,
U.S. Department of Commerce, 1985.
11. Deer, W.A., R. A. Howie, and J. Zussman, A,n Introduction to the Rock Forming
Minerals, Longman, 1966.
12. Heinrich, E. W., Microscopic Identification of Minerals, McGraw Hill, 1965.
13. Kressler, J. R., "Changes in Optical Properties of Chrysotile During Acid
Leaching", The Microscope, 31, 1983, pp. 165-172.
14. Prentice, J. and M. Keech, "Alteration of Asbestos with Heat", Microscopy and
Analysis, 10, 1989, pp. 7-12.
15. Laughlin, G. and W. C. McCrone, "The Effect of Heat on the Microscopical
Properties of Asbestos", The Microscope, 37, 1989, pp. 8-15.
16. Interim Method for the Determination of Asbestos in Bulk Insulation Samples,
U.S. E.P.A. 600/M4-82-020, 1982.
17. McCrone, Walter C., "Routine Detection and Identification of Asbestos", The
Microscope, 33, 1985, pp. 273-284
18. Reports of Analysis, SRM 1866 and 1867, National Institute of Standards &
Technology.
19. McCrone, Walter C., Asbestos Identification, McCrone Research Institute, 1987.
2.3 Gravimetry
2.3.1 Principle and Applicability
Many components of bulk building materials, specifically binder components, can be
selectively removed using appropriate solvents or, in the case of some organics, by ashing.
The removal of these components serves the following purposes:
j
23
-------
1) to isolate asbestos from the sample, allowing its weight to be determined;
2) to concentrate asbestos and therefore lower the detection limit in the total sample;
3) to aid in the detection and identification of fibrous components; and,
4) to remove organic (ashable) fibers which are optically similar to asbestos.
Common binder materials which are removed easily using the techniques described
include: 1) calcite, gypsum, magnesite, brucite, bassanite, portlandite, and dolomite, using
hydrochloric acid, and 2) vinyl, cellulose, and other organic components, by ashing. The
removal of the binder components results in a residue containing asbestos, if initially present,
and any other non-soluble or non-ashable components which were present in the original
sample. Unless the procedures employed result in the loss of some asbestos, the weight
percent of the residue is the upper limit for the weight percent of asbestos in the sample.
This section describes the procedure for removing acid-soluble and ashable components,
and fer determining the weight percent of the residue. However, the acid dissolution and
ashing techniques can be used without the accompanying weight measurements to either
liberate or clean fibers to aid in qualitative PLM or AEM analyses.
This technique is not an identification techr-ique. Other methods, such as PLM, XRD, or
AEM must be-used to determine the identity of the components. A description of the
suggested apparatus, reagents, etc. needed for the techniques described is included in
Appendix B.
2.3.2 -Interferences /
/
Any components which cannot by .removed from the sample by selective dissolution or
ashing interfere with asbestos quantitation. These components include, but are not limited to,
many silicates (micas, glass fibers, etc.) and oxides (TiOj, magnetite, etc.). When interfering
phases are present (the residue contains other phases in addition to asbestos), other
techniques such as PLM, AEM, or XRD must be used to determine the percent of asbestos
in the residue.
24
-------
Care must be taken to prevent loss of or chemical/structural changes in the critical
components (asbestos). Prolonged exposure to acids or excessive heating (above 500°C) can
cause changes in the asbestos components in the sample and affect the optical properties '2 ^
2.3.3 Quantitation
The weight of the residue remaining after solvent dissolution/ashing should be compared
with the original weight of the material. Presuming no insoluble material is lost, the weight
percent of the residue is the upper limit for the amount of asbestos in the sample. If the
*••
residue is comprised only of asbestos, then the weight percent of residue equals the weight
percent of asbestos in the sample. If the residue contains other phases, then techniques such
as PLM, XRD, or AEM must be employed to determine the relative abundance of asbestos
in the residue.
The precision and accuracy of the technique are dependent upon the homogeneity of the
material, the accuracy of the weight measurements, and the effectiveness of the sample
reduction and filtering procedures. In practice, the precision can be equal to +.1 %, and the
accuracyat 1 wj% asbestos can be less than or equal to +.10% relative.
The incomplete solution of components and the presence of other nonasbestos components
in the residue-contribute to producing a positive bias for the technique (falsely high
» •
percentages of asbestos).
2.3.4 Preliminary Examination and Evaluation
Stereomicroscopic and PLM examinations of the sample should already have been
conducted prior to initiating this procedure. These examinations should have provided
information about: 1) whether the sample contains components which can be removed by
acid-washing, solvent dissolution, or ashing, and 2) whether the sample contains asbestos, or
fibers that might be asbestos, or whether no asbestos was detected.
If the sample is friable and contains organic (ashable) components, the ashing procedure
should be followed. If the sample is friable and contains HCl-soluble components, the acid
dissolution procedure should be followed. If the sample is friable and contains both types of
25
-------
components, the two procedures can be applied, preferably with acid dissolution following
ashing.
If the sample is nonfriable (e.g. floor tiles), it is also recommended that the ashing
procedure be used first, followed by the acid dissolution procedure The ashing procedure
reduces floor tiles to a material which is easily powdered, simplifying the sample preparation
for acid dissolution.
2.3.5 Sample Preparation
2.3.5.1 Drying
Any moisture in the sample will affect the weight measurements, producing falsely low
percentages of residue. If the sample is obviously wet, it should be dried at low temperature
(using a heat lamp, or simply by exposure at ambient conditions, prior to starting the
weighing procedure). If an oven is used, the drying temperature should not exceed 60°C.
Drying b^ means of heat lamp or ambient air must be performed within a safety-filtered
hood. Even if the sample appears dry, it can contain enough moisture to affect the precision
and accuracy of the technique. The test for sample moisture involves placing the amount of
sample to be used on the weighing pan; if the weight remains stable with time, then the
sample is dry enough. If the weight decreases as the sample sits on the weighing pan, then
the sample should be dried. Where conditions of moderate to high humidity are known to
exist, all materials to be weighed should be allowed time to stabilize to these ambient
conditions.
2.3.5.? Homogenization/Grain Size Reduction
To increase the accuracy and precision of the acid dissolution technique, the sample
should be homogenized prior to analysis. This reduces the grain size of the binder material
and releases it from fiber bundles so that it may be dissolved in a shorter time period.
Leaving the sample in the acid for a longer period of time to complete the dissolution process
can adversely affect the asbestos componentsv and is not recommended. Homogenization of
the sample also ensures that any material removed for analysis will more likely be
representative of the entire sample.
26
-------
Hojiiogenization of friable samples prior to ashing may also accelerate the ashing process;
however, the ashing time can simply be increased without affecting the asbestos in the
sample. Nonfriable samples, such as vinyl floor tiles, can be broken or shaved into pieces to
increase surface area and accelerate the ashing process
Homogenization and grain size reduction can be accomplished in a variety of \vays- 1)
hand grinding in a mortar and pestle; 2) crushing with pliers or similar instrument; 3) mixing
in a blender; 4) milling (i.e. Wylie mill, cryomill, etc.); or 5) any other technique which
seems suitable. If the fibers are extremely long, a pair of scissors or similar implement can
be used to reduce the fiber length.
2.3.6 Procedure for Ashing
1) Weigh appropriate amount of material.
There is no restriction on the maximum weight of material used; however, a large
amount of material may take longer to ash. Enough material should be used to avoid
a significant contribution of weighing errors to 'he total accuracy and precision.
2) Place material in crucible, weigh, and cover with lid.
•
Placing a lid on the crucible both minimizes the amount of oxygen available, slowing
the rate of combustion of the sample, and prevents any foreign material from falling
into the crucible during ashing.
3) Place crucible into furnace, and ash for at least 6 hours.
The furnace temperature at the sample position should be at least 300°C but should
not exceed 500°C. If the sample combusts (burns), the temperature of the sample
may exceed 500°C. Chrysotile will decompose above approximately 500°C.
The furnace area should be well-ventilated and the fumes produced by ashing should
be exhausted outside the building.
<
The ashing time is dependent on the furnace temperature, the amount of sample, and
the surface area (grain size). Six hours at 450°C is usually sufficient.
4) Remove crucible from furnace, allow contents to adjust to room temperature
and humidity, and weigh.
t
-------
5) Divide residue weight by starting weight and multiply by 100 to determine
weight % residue.
6) Analyze residue and/or proceed to acid dissolution procedure.
If the objective was to remove organic fibers that may be confused optically with
asbestos, examine residue with PLM to determine whether any fibers remain.
If the sample is a floor tile, the acid dissolution procedure must now be performed
The residue does not have to be analyzed at this stage.
2.3.7 Use of Solvents for Removal of Organics
Solvent dissolution may be used as a substitute for low temperature ashing for the
purpose of removing organic interferences from bulk building materials. However, solvent
dissolution, because of the involvement of potentially hazardous reagents such as
tetrahydrofuran, amyl acetate, 1-1-1, trichlorethane, etc., requires that all work be
performed with extreme caution inside a biohazard hood Material Safety Data Sheets
should be reviewed before using any solvent. Solvent dissolution involves more apparatus
than does ashing, and requires more time, mainly due to set-up and slow filtration resulting
fronKviscoiis solvent/residue mixtures.
.**-:
4>
The following is a brief description of the solvent dissolution process.
1J Weigh starting material.
Place approximately 15-25ml of solvent in a 100ml beaker. Add 2.5-3.0 grams
(carefully weighed for continued gravimetric tracking) of powdered sample.
2) Untrasonicate sample.
Place the beaker in an ultrasonic bath (or ultrasonic stirrer) for approximately 0.5
hqurs. The sample containers should be covered to preclude escape of an aerosol
spray.
3) Centrifuge sample.
Weigh centrifuge vial before adding beaker ingredients. Wash beaker with an
additional 10-15ml of solvent to remove any remaining concentrate. Then centrifuge
28
-------
at approximately 2000-2500 rpm for 0.5 hour. Use solvent-iesistant centrifuge
tubes.
4) Decant sample, reweigh.
After sepafation by centrifuging, decant solvent by pipetting. Leave a small amount
of solvent in the centrifuge vial to minimize the risk of decanting solid concentrate
Allow solid concentrate to dry in vial, then reweigh.
2.3.8 Procedure for Acid Dissolution
1) Weigh starting material, transfer to acid resistant container.
•
Small, dry sample weights between O.lg and 0.5g are recommended (determined for
47mm filters - adjust amount if different diameter filters are used). If too much
'^material is left after acid dissolution the filter can get clogged and prevent complete
filtration. Very small samples are also to be avoided, as the weighing errors will
have a large effect on the total accuracy and precision of the technique.
2) Weigh filter.
3) Add HC1 to sample in container, stir, allow to sit for 2-10 minutes.
Either concentrated or dilute HC1 can be used. If concentrated HC1 is used, add
enough acid to completely soak the material, allow the reaction to proceed to
completion, and then dilute with distilled water. Alternatively, a dilute solution,
made by adding concentrated HC1 to distilled water, can be used in the place of
concentrated HC1. A solution of 1 part concentrated HC1 to 3 parts distilled water
(approximately 3N solution) has been found to be quite effective in removing
components within 5 minutes. For a sample size less than 0.5g, 20-30 ml of a 3N
HCI solution is appropriate. In either case (using concentrated or dilute HC1), the
reaction will be more effective if the sample has been homogenized first. All
obvious signs of reaction (bubbling) should cease before the sample is filtered. Add
fresh acid, a ml or two at a time, to ensure complete reaction. It should be noted
that if dolomite is present, a 15-20 minute exposure to concentrated HCI may be
required to completely dissolve the carbonate materials.
.NOTE: Other solvents may be useful for selective dissolution of nonasbestos
components. For example, acetic acid will dissolve calcite, and will not dissolve
' asbestos minerals. If any solvent other than hydrochloric acid is used for the
dissolution of inorganic components, the laboratory must be able to demonstrate that
jthe solvent does not remove asbestos from the sample.
29
-------
4) Filter solution.
Use the pre-weighed filter. Pour the solution into the vacuum filter assembly, then
rinse all material from container into filter assembly. Rinse down the inside walls of
the glass filter basin and check
-------
wt% asbestos in floor tile = (B x C -*• 100) x A •*• 100 = 10 x 70 4- 100 = 7%
If weights are expressed in decimal form, multiply the weight % of asbestos in the
sample by the weight % of the residue from the ashing procedure, then multiply by
100.
wt% asbestos after HC1 dissolution = B x C = 0.2 x 0.5 = 0.1 (x 100 = 10%)
wt% asbestos in floor tile = (B x C) x A = 0.1 x 0.7 = 0.07 (x 100 = 7%)
2.3.9 Determination of Optimal Precision and Accuracy
The precision of the technique can be determined by extracting multiple subsamples from
the'original sample and applying the same procedure to each. The optimal accuracy of the
technique can be determined by applying gravimetric standards. Mixtures of calcite and
asbestos (chrysotile, amosite, etc.) in the following proportions are recommended for testing
the accuracy of the acid dissolution technique: 0.1 wt% asbestos/99.9 wt% calcite, 1.0 wt%
asbestos/99.0 wt% calcite, and 10 wt% asbestos/90 wt% calcite. Mixtures of cellulose and
asbestos are useful for testing the accuracy of the ashing technique.
Mixtures of only two components, as described above, are simplifications of "real-world"
samples. The accuracy determined by analyzing these mixtures is considered optimal and
may not apply directly to the measurement of each unknown sample. However, analyzing
replicates and standards using the full laboratory procedure, including homogemzation,
ashing, acid dissolution, filtration, and weighing, may uncover steps that introduce significant
bias or variation that the laboratory may then correct.
2.3.10 References
1. Kressler, J. R., "Changes in Optical Properties of Chrysotile During Acid
Leaching", The Microscope, 31, 1983, pp. 165-172.
• •
2. Prentice, J. and M. Keech, "Alteration of Asbestos with Heat", Microscopy and
Analysis, March 1989.
»3. Laughlin, G. and W. C. McCrone, "The Effect of Heat on the Microscopical
Properties of Asbestos",.The Microscope, 37, 1989, pp. 8-15.
31
-------
2.4 X-Ray Powder Diffraction
2.4.1 Principle and Applicability
The principle of x-ray powder diffraction (XRD) analysis is well established.12 Any
solid crystalline material will diffract an incident beam of parallel, monochromatic x-rays
whenever Bragg's Law,
X = 2d sin 0,
is satisfied for a particular set of planes in the crystal 'altice, where
X ='the x-ray wavelength, A;
d = the interplanar spacings of the set of reflecting lattice planes, A and
8 = the angle of incidence between the x-ray beam and the reflecting lattice planes.
By appropriate orientation of a sample relative to the incident x-ray beam, a diffraction
pattern can be generated that will be uniquely characteristic of the structure of the crystalline
phases present.
Unlike optical methods of analysis, however, XRD cannot determine crystal morphology.
Therefore, in asbestos analysis, XRD does not distinguish between fibrous and nonfibrous
forms of the serpentine and ainphibole minerals (Table 2-6). However, when used in
conjunction with methods such as PLM or AEM, XRD techniques can provide a reliable
analytical method for the identification and characterization of asbestiform minerals in bulk
materials.
For qualitative analysis by XRD methods, samples should initially be scanned over
limited diagnostic peak regions for the serpentine ( — 7.4 A) and amphibole (8.2-8.5 A)
minerals (Table 2-7). Standard slow-scanning methods for bulk sample analysis may be used
for materials shown by PLM to contain significant amounts of asbestos (>5 percent).
Detection of minor or trace amounts of asbestos may require special sample preparation a.nd
step-scanning analysis. All samples that exhibit diffraction peaks in the diagnostic regions
for asbestiform minerals should be submitted to a full (5°-60° 26; 1° 20/min) qualitative
XRD scan, and their diffraction patterns should be compared with standard reference powder
I
32
-------
diffraction patterns3 to verify initial peak assignments and to identify possible matrix
interferences when subsequent quantitative analysis will be performed.
Accurate quantitative analysis of asbestos in bulk samples by XRD is critically
dependent on particle size distribution, crystallite size, preferred orientation and matrix
absorption effects, and comparability of standard reference and sample materials. The most
intense diffraction peak that has been shown to be free from interference by prior qualitative
XRD analysis should be selected for quantitation of each asbestiform mineral. A "thin-layer"
method of analysis5-6 can be used in which, subsequent to comminution of the bulk material
to ~ 10 /xm by suitable cryogenic milling techniques, an accurately known amount of the
sample is deposited on a silver membrane filter. The mass of asbestiform material is
determined by measuring the integrated area of the selected diffraction peak using a step-
scanning mode, correcting for matrix absorption effects, and comparing with suitable
•
calibration standards. Alternative "thick-layer" or bulk methods7/ are commonly used for
semi-quantitative analysis.
33
-------
TABLE 2-6. THE ASBESTOS MINERALS AND THEIR
NONASBESTIFORM ANALOGS
Asbestiform
Serpent. r.e
Chrysotile
Amphibole
Anthophyllite asbestos
Cummingtonite-grunerite
asbestos (Amosite)
Crocidolite
Tremolite asbestos
Actinohte asbestos
Nonasbestiform
Antigonte, lizardite
Anthophyllite
Cumrrungtonite-
grunerite
Riebeckite
Tremolite
Actinohte
Chemical Abstract
Service No
12001-29-5
77536-67-5
12172-73-5
12001-28-4
77536-68-6
77536-66-4
TABLE 2-7. PRINCIPAL LATTICE SPACINGS OF ASBESTIKORM MINERALS'
Minerals
Chrysotile (Serpentine)
AmoMte (Grunenle)
Anihophylhte
Crocidolite (Riebeckite)
Actinohte
Tremolite
Principal d-spacings (A)
and relative intensities
731100
736^
1 lO.oo
833,00
822,oo
305^
306,oo
835,oo
840,oo
2.72,oo
838100
2706,00
3.1310o
365,o
366go
233M
306™
3 060.J
324«,
833-0
3 1055
3 1255
254100
312,00
3 14,5
2.706M
457,0
245U
355-0
2756-0
325-,
826,,
323^
2 720,j
2726,0
340,0
2705*
843,0
8.44,0
JCPDS
Powder diffraction file:
number
21-5433
25-645
22-1162 (theoretical)
17-745 (nonfibrous)
27-1 170 (U1CC)
9-455
16-401 (synthetic)
27-1415 (UICC)
19-1061
25-157
13-4373
20-13 10' (sjnthetic)
23-666 (synthetic mixture
w/nchtente)
1. This information is intended as a guide only. Complete powder diffraction data, including
mineral type and source, should be referred to ensure comparability of sample and reference '
materials where possible. Additional precision XRD data on amosite, crocidolite, tremohle and
Chrysotile are available from the U S. Bureau of Mines, Reference 4.
2. From Reference 3
3. Fibrosity questionable '•
34
-------
This XRD method is applicable as a confirmatory method for identification and
quantitatjbn of asbestos in bulk material samples that have undergone prior analysis by PLM
or other optical methods.
2.4.2 Range and Sensitivity
The range and sensitivity of the method have not been determined. They will be variable
and dependent upon many factors, including matrix effects (absorption and interferences),
diagnostic reflections selected and their relative intensities, preferred orientation, and
instrumental limitations. A detection limit of one percent is feasible given certain sample
characteristics.
2.4.3" Limitations
2.4.3.1 Interferences
Since the asbestiform and nonasbestiform analogs of the serpentine and amphibole
minerals (Table 2-7) are indistinguishable by XRD techniques unless special sample
preparation techniques and instrumentation are used,9 the presence of nonasbestiform
•
serpentines and amphiboles in a sample will pose severe interference problems in the
identification and quantitative analysis of their asbestiform analogs.
The use of XRD for identification and quantitation of asbestiform minerals in bulk
samples may also be limited by the presence of other interfenng materials in the sample.
For naturally-occurring materials, the commonly associated asbestos-related mineral
interferences can usually be anticipated. However, for fabricated materials, the nature of the
interferences may vary greatly (Table 2-8) and present more serious problems in
identification and quantitation.10 Potential interferences are summarized in Table 2-9 and
include the following:
• Chlorite has major peaks at 7.19 A and 3.58 A that interfere with both the primary
(7.31 A) and secondary (3.65 A) peaks for serpentine (chrysotile). Resolution of the
primary peak to give good quantitative results may be possible when a step-scanning
mode of operation is employed.
• Vermiculite has secondary peaks at 7.14 A and 3.56 A that could interfere with the
primary peak (7.31 A) and a secondary peak (3.65 A) of serpentine ^chrysolite).
35
-------
TABLE 2-8. COMMON CONSTITUENTS IN BUILDING MATERIAL
(From Rcf. 10)
CO
A. Insulation Materials
Chrysotilc
Amosite
Crocidolite
*Rock wool
*Slag wool
* Fiber glass
Gypsum (CaSO4 • 2H/))
Vc'rmiculitc (micas)
•Perlite
Clays (kaolin)
•Wood pulp
*Paper fibers (talc, clay
carbonate filters)
Calcium silicates (synthetic)
Opaques (chromite, magnetite
inclusions in serpentine)
Hematite (inclusions in "amosite")
Magnesite
*Diatomaceous earth
B. Flooring MateriaU
Calcite,
Dolomite
Titanium Oxide
Quartz
Antigorite
Chrysotile -,
Anthophyllite
Tremolite
'Organic binders
Talc
Wollastonite
C. Spray Finishes or Paints
Bassanite
Carbonate minerals (calcitc,
dolomite, vatcrite)
Talc
Tremolite
Anthophyllite
Serpentine (including chrysotile)
Amosite
Crocidolitc
'Mineral wool
*Rock wool
*SIag wool
* Fiber glass
Clays (kaolin)
Micas
Chlorite
Gypsum
Quartz
*Orgamc binders and thickeners
Hydromagnesite
Wollastonite
Opaques (cbromitc, magnetite
inclusion in serpentine)
Hematite (inclusions in "amosite")
D. Cementitious Materials
Chrysotile
Amosite
"' Crocidolitc
Micas
Fiber glass
Cellulose
Animal hair
Quartz
Gypsum
Calcite
Dolomite
Calcium silicates
E. Roofing Materials
Chrysotilc
Cellulose
Fiber glass
Mineral Wool
Asphalt
Quartz
Talc
Micas
* Amorphous materials—contribute only to overall scattered radiation and increased background radiation.
-------
TABLE 2-9 INTERFERENCES IN XRD ANALYSIS OF
ASBESTIFORM MINERALS
Asbestiform
Mineral
Primary diagnostic
peaks (approximate
d spacings in A)
Interference
Serpentine
Chrysotile
7.3
3.7
Nonasbestiform serpentines, (antigorite,
lizardite), chlorite, vermicuhte, sepiolite,
kaolinite, gypsum
Nonasbestiform serpentines (antigorite,
lizardite), chlorite, vermicuhte, halloysite,
cellulose
Ampfiibole
Amosite (Grunerite)
Antnophyllite
Crocidolite
(Riebeckite)
Tremolite
Actmolite
3.1
8.3
Nonasbestiform amphiboles (grunerite-
cummingtomte, anthophylhte, riebeckite,
tremolite), mutual interferences, talc,
carbonates
Nonasbestiform amphiboles (grunente-
cummingtomte, anthophylhte, riebeckite,
tremolite), mutual interferences
• Sepiolite produces a peak at 7.47 A which could interfere with the primary peak
(7.31 A) of serpentine (chrysotile).
• Halloysite has a peak at 3.63 A that interferes with the secondary (3.65 A) peak for
serpentine (chrysotile).
• Kaolinite has a major peak at 7.15 A that may interfere with the primary peak of
serpentine (chrysotile) at 7.31 A when present at concentrations of > 10 percent.
However, the secondary serpentine (chrysotile) peak at 3.65 A may be used for
quantitation.
• Gypsum has a major peak at 7.5 A that overlaps the 7.31 A peak of serpentine
(chrysotile) when present as a major sample constituent. This may be removed by
careful washing with distilled water, or by heating to 300°C to convert gypsum to
plaster of paris (bassanite).
• Cellulose has a broad peak that partially overlaps the secondary (3.65 A) serpentine
(chrysotile) peak.8
37
-------
• Overlap of major diagnostic peaks of the amphibole minerals, grunerite (amosite),
anthophyllite, riebeckite (crocidolite), and tremolite, at approximately 8.3 A and 3.1
A causes mutual interference when these minerals occur in the presence of one
another. In some instances adequate resolution may be attained by using step-
scanning methods and/or by decreasing the collimator slit width at the x-ray port.
• Carbonates may also interfere with quantitative analysis of the amphibole minerals
grunerite (amosite), anthophyllite, riebeckite (crocidolite), and tremohte-actinohte.
Calcium carbonate (CaC03) has a peak at 3.035 A that overlaps major amphibole
peaks at approximately 3.1 A when present in concentrations of >5 percent.
Removal of carbonates with a dilute acid wash is possible; however, the time in acid
should be no more than 20 minutes to preclude any loss of chrysotile."
• A major talc peak at 3.12 A interferes with the primary tremolite peak at this same
position and with secondary peaks of actmolite (3.14 A), riebeckite (crocidolite) (3 10
A), grunerite (amosite) (3.06 A), and anthophyllite (3.05 A). In the presence of talc,
the major diagnostic peak at approximately 8 3 A should be used for quantitation of
these asbestiform minerals.
The problem of intraspecies and matrix interference is further aggravated by the
variability of the silicate mineral powder diffraction patterns themselves, which often makes
definitive identification of the asbestos minerals by comparison with standard reference
*•
diffracfcpn patterns difficult. This variability results from alterations in the crystal lattice
associated with differences in isomorphous substitution and degree of crystallmity. This is
especially true for the amphiboles. These minerals exhibit a wide variety of very similar
chemical compositions, resulting in diffraction patterns characterized by having major (110)
reflections of the monoclinic amphiboles and (210) reflections of orthorhombic anthophyllite
separated by less than 0.2 A.12
2.4.3.2 Matrix Effects
If a copper x-ray source is used, the presence of iron at high concentrations in a sample
will result in significant x-ray fluorescence, leading to loss of peak intensity, increased
background intensity, and an overall decrease in sensitivity. This situation may be corrected
by use of an x-ray source other than copper; however, this is often accompanied both by loss
of intensity and by decreased resolution of closely spaced reflections. Alternatively, use of a
38
-------
diffracted beam monochromator will reduce background fluorescent radiation, enabling
weaker diffraction peaks to be detected.
X-ray absorption by the sample matrix will result in overall attenuation of the diffracted
beam and may seriously interfere with quantitative analysis. Absorption effects may be
minimized by using sufficiently "thin" samples for analysis.5il3i!4 However, unless absorption
effects are known to be the same for both samples and standards, appropriate corrections
should be made by referencing diagnostic peak areas to an internal standard7-8 or filter
substrate (Ag) peak.5-6
2.4,3.3 Particle Size Dependence
Because the intensity of diffracted x-radiation is particle-size dependent, it is essential for
accurate quantitative analysis that both sample and standard reference materials have similar
particle size distributions. The optimum particle size (i.e., fiber length) range for
quantitatixfe analysis of asbestos by XRD has been reported to be 1 to 10 jtm.15
Comparability of sample and standard reference material particle size distributions should be
verified by optical microscopy (or another suitable method) prior to analysis.
2.4.3.4 Preferred Orientation Effects
Preferred orientation of asbestiform minerals during sample preparation often poses a
serious problem in quantitative analysis by XRD. A number of techniques have been
developed for reducing preferred orientation effects in "thick layer" samples.7M
-------
provide standard reference materials for chrysotile, amosite and crocidoiite (SRM 1866) and
anthophyllite, tremolite and actinolite (SRM 1867).
In addkion, the problem of ensuring the comparability of standard reference and sample
materials, particularly regarding crystallite size, particle size distribution, and degree of
crystalljnity, has yet to be adequately addressed. For example, Hanger et al.18 have observed
that in insulating matrices, chrysotile tends to break open into bundles more frequently than
amphipoles. This results in a line-broadening effect with a resultant decrease in sensitivity.
Unless this effect is the same for both standard and sample materials, the amount of
chrysotile in the sample will be under-estimated by XRD analysis. To minimize this
problem, it is recommended that standardized matrix reduction procedures be used for both
sample and standard materials.
2.4.4 Precision and Accuracy
Neither the precision nor accuracy of this method has been determined. The individual
laboratory should obtain or prepare a set of calibration materials containing a range of
asbestos weight percent concentrations in combination with a variety of matrix/binder
materials. Calibration curves may be constructed for use in semi-quantitative analysis of
bulk materials.
2.4.5 Procedure
2.4.5.1 Sampling
Samples taken for analysis of asbestos content should be collected as specified by EPA19
2.4,5.2 Analysis
All samples must be analyzed initially for asbestos content by PLM. XRD may be used
as an additional technique, both for identification and quantitation of sample components.
Note: Asbestos is a toxic subsJance. All handling of dry materials should be performed
in 'a safety-hood.
40
-------
2.4.5.2.1 Sample Preparation
The method of sample preparation required for XRD analysis will depend on: (1) the
condition of the sample received (sample size, homogeneity, particle size distribution, and
overall composition as determined by PLM); and (2) the type of XRD analysis to be
performed (qualitative or quantitative; thin-layer or bulk).
Bulk materials are usually received as heterogeneous mixtures of complex composition
•
with very wide particle size distributions. Preparation of a homogeneous, representative
sample from asbestos-containing materials is particularly difficult because the fibrous nature
of the asbestos minerals inhibits mechanical mixing and stirring, and because milling
procedures may cause adverse lattice alterations.
A discussion of specific matrix reduction procedures is given below. Complete methods
of sample preparation are detailed in Sections 2.4.5.3 and 2.4.5.4. Note: All samples
should be examined microscopically before and after each matrix reduction step to
monitor changes in sample particle size distribution, composition, and crystallinity, and
to ensure sample representativeness and homogeneity for analysis.
2.4.5.2.2 Milling
Mechanical milling of asbestos materials has been shown to decrease fiber crystallinity,
with a resultant decrease in diffraction intensity of the specimen; the degree of lattice
alteration is related to the duration and type of milling process.30"23 Therefore, all milling
times should be kept to a minimum.
For qualitative analysis, particle size is not usually of critical importance and initial
characterization of the material with a minimum of matrix reduction is often desirable to
document the composition of the sample as received. Bulk samples of very large particle
size (>2-3 mm) should be comminuted to - 100 ^tm. A mortar and pestle can sometimes be
used in size reduction' of soft or loosely bound materials though this may cause matting of
some samples. Such samples may be reduced jy cutting with a razor blade in a mortar, or
by grinding in a suitable mill (e.g., a microhamrner mill or equivalent). When using a
mortar for grinding or cutting, the sample should be moistened with ethanol, or some other
41
-------
suitable wetting agent, to minimize exposure, and the procedure should be performed in a
HEPA-filtered hood.
For accurate, reproducible quantitative analysis, the particle size of both sample and
standard materials should be reduced to ~ 10 nm , Dry ball milling at liquid nitrogen
temperatures (e.g., Spex Freezer Mill*, or equivalent) for a maximum time of 10 minutes
(some samples may require much shorter milling time) is recommended to obtain satisfactory
particle size distributions while protecting the integrity of the crystal lattice.5 Bulk samples
of very large particle size may require grinding in two stages for full matrix reduction to
Final particle size distributions should always be verified by optical microscopy or
another suitable method.
2.4.5.2.3 Ashing
For materials shown by PLM to contain large amounts of cellulose or other organic
*
materials, it may be desirable to ash prior to analysis to reduce background radiation or
matrix interference. Since chrysotile undergoes dehydroxylation at temperatures between
550°C and 650°C, with subsequent transformation to forsterite,34-25 ashing temperatures
should be kept below 500°C. Use of a muffle furnace is recommended. In all cases,
calibration of the furnace is essential to ensure that a maximum ashing temperature of 500°C
is not exceeded (see Section 2.3).
2.4.5.2.4 Acid Washing
Because of the interference caused by gypsum and some carbonates in the detection of
asbestiform minerals by XRD (see Section 2.4.3.1), it may be necessary to remove these
interferences by a simple acid washing procedure prior to analysis (see Section 2.3),
2.4.5.3 Qualitative Analysis
2. 4. 5.3.1'. Initial Screening of Bulk Material
Qualitative analysis should be performed on a representative, homogeneous portion of the
sample, with a minimum of sample treatment, using the following procedure: ;
42
-------
1. Grind and mix the sample with a mortar and pestle (or equivalent method, see Section
2*4.5.2.2) to a final particle size sufficiently small (~ 100 pm) to allow adequate
packing into a sample holder.
2. Pack sample into a standard bulk sample holder. Care should be taken to ensure lhat
a representative portion of the milled sample is selected for analysis. Particular care
should be taken to avoid possible size segregation of the sample, (Note: Use of
back-packing method26 for bulk sample preparation may reduce preferred
orientation effects.)
3. Mount the sample on the diffractometer and scan over the diagnostic peak regions for
the serpentine (-7.4 A) and amphibole (8.2-8.5 A) minerals (see Table 2-7). The x-
ray diffraction equipment should be optimized for intensity. A slow scanning speed
of 1° 20/min is recommended for adequate resolution. Use of a sample spinner is
recommended.
4. Submit all samples that exhibit diffraction peaks in the diagnostic regions for
asbestiform minerals to a full qualitative XRD scan (5°-60° 20; 1° 20/min) to verify
initial peak assignments and to identify potential matrix interferences when subsequent
quantitative analysis is to be performed.
5. Compare the sample XRD pattern with standard reference powder diffraction patterns
(i.e., JCPDS powder diffraction data3 or those of other well-characterized reference
materials). Principal lattice spacings of asbestiform minerals are given in Table 2-7;
common constituents of bulk insulation and wall materials are listed in Table 2-8.
2.4.5.3.2 Detection of Minor or Trace Constituents
Routine screening of bulk materials by XRD may fail to detect small concentrations
(< 1%) of asbestos. The limits of detection will, in general, be improved if matrix
absorption effects are minimized, and if the sample particle size is reduced to the optimal 1
to 10 urn range, provided that the crystal lattice is not degraded in the milling process.
Therefore, in those instances when confirmation of the presence of an asbestiform mineral at
very low levels is required, or where a negative result from initial screening of the buik
material by XRD (see Section 2.4.5.3.1) is in conflict with previous PLM results, it may be
desirable to prepare the sample as described for quantitative analysis (see Section 2.4.5.4)
and step-scan over appropriate 26 ranges of selected diagnostic peaks (Table 2-7). Accurate
43
-------
transfer of the sample to the silver membrane filter is not necessary unless subsequent
quantitative analysis is to be performed.
2.4.5,4 Quantitative Analysis
The proposed method for quantitation of asbestos in bulk samples is a modification of the
NIOSH-recommended thin-layer method for chrysotile in air.6 A thick-layer bulk method
involving pelletizing the sample may be used for semi-quantitative analysis;78 however, this
method requires the addition of an internal standard, use of a specially fabricated sample
press, and relatively large amounts of standard reference materials. Additional research is
required to evaluate the comparability of thin- and thick-layer methods for quantitative
asbestos analysis.
For quantitative analysis by thin-layer methods, the following procedure is recommended:
1. Mill and size ah or a substantial representative portion of the sample as outlined in
Section 2.4.5.2.2.
«V
2. Dry at 60°C for 2 hours; cool in a desiccator.
3. Weigh accurately to the nearest 0.01 mg,
4. Samples shown by PLM to contain large amounts of cellulosic or other organic
materials, gypsum, or carbonates, should be submitted to appropriate matrix
reduction procedures described in Sections 2.4.5.2.3 and 2.4.5.2.4. After ashing
and/or acid treatment, repeat the drying and weighing procedures described above,
and determine the percent weight loss, L.
5. Quantitatively transfer an accurately weighed amount (50-100 mg) of the sample to a
1-L volumetric flask containing approximately 200 mL isopropanol to which 3 to 4
drops of surfactant have been added.
6. Ultrasonicate for 10 minutes at a power density of approximately 0.1 W/mL, to
disperse the sample material.
7. Dilute to volume with isopropanol.
8. Place flask on a magnetic-stirring plate. Stir.
9. Place silver membrane filter on the filtration apparatus, apply a vacuum, and attach
the reservoir. Release the vacuum and add several milliliters of isopropanol to the
reservoir. Vigorously hand shake the asbestos suspension and immediately withdraw
44
-------
an aliquot from the center of the suspension so that total sample weight, WT, on the
filter will be approximately 1 mg. Do not adjust the volume in the pipet by
expelling part of the suspension; if more than the desired aliquot is withdrawn,
discard the aliquot and repeat the procedure with a clean pipet. Transfer the aliquot
to the reservoir. Filter rapidly under vacuum. Do not wash the reservoir walls.
Leave the filter apparatus under vacuum until dry. Remove the reservoir, release
the vacuum, and remove the filter with forceps. (Note: Water-soluble matrix
interferences such as gypsum may be removed at this time by careful washing of the
filtrate with distilled water. Extreme-care should be taken not to disturb the sample.)
10. Attach the filter to a flat holder with a suitable adhesive and place on the
diffractometer. Use of a sample spinner is recommended.
11. For each asbestos miners to be quantitated, select a reflection (or reflections) that
has (have) been shown to be free from interferences by prior PLM or qualitative
XRD analysis and that can be used unambiguously as an index of the amount of
material present in the sample (see Table 2-7).
12. Analyze the selected diagnostic reflection(s) by step-scanning in increments of 0.02°
20 for an appropriate fixed time and integrating the counts. (A fixed count scan may
be used alternatively; however, the method chosen should be used consistently for all
samples and standards.) An appropriate scanning interval should be selected for
each peak, and background corrections made. For a fixed time scan, measure the
background on each side of the peak for one-half the peak-scanning time. The net
intensity, I,, is the difference between the peak integrated count and the total
background count.
13. Determine the net count, IAg, of the filter 2.36 A silver peak following the
procedure in step 12. Remove the filter from the holder, reverse it, and reattach
it to the holder. Determine the net count for the unattenuated silver peak, I^g
Scan times may be less for measurement of silver peaks than for sample peaks';
however, they should be constant throughout the analysis.
• '
14. Normalize all raw, net intensities (to correct for instrument instabilities) by
referencing them to an external standard (e.g., the 3.34 A peak of an a-quartz
reference crystal). After each unknown is scanned, determine the net count,
I°r, of the reference specimen following the procedure in step 12. Determine
the normalized intensities by dividing the peak intensities by I°r:
45
-------
* a *
Ja = T' TAg
2.4.6 Calibration
2.4.6.1 Preparation of Calibration Standards
1. Mill and size standard asbestos materials according to the procedure outlined in
Section 2.4.5.2.2, Equivalent standardized matrix reduction and sizing
techniques should be used for both standard and sample materials.
2. Dry at 1QO°C for 2 hours; cool in a desiccator.
*
3. Prepare' two suspensions of each standard in isopropanol by weighing approximately
10 and^SQ mg-of the dry material to the nearest 0.01 aig. Transfer each to a i-L
volumetric flask containing approximately 200 mL isopropanol to which a few drops
of surfactant have been added.
4. Ultrasoni&te for 10 minutes at a power density of approximately 0.1 W/mL, to .
disperse tp asbestos material.
5. Dilute to volume with isopropanol.
«
6. Place the flask on a magnetic stirring plate. Stir.
7, -Prepare, in triplicate, a series of at least five standard filters to cover the desired
analytical range, using appropriate aliquots of the 10 and 50 mg/L suspensions. For
each standard, mount a silver membrane filter on the filtration apparatus. Place a
few mL of isopropanol in the reservoir. Vigorously hand shake the asbestos
suspension and immediately withdraw an aliquot from the center of the suspension.
Do not adjust the volume in the pipet by expelling part of the suspension; if more
than the desired aliquot is withdrawn, discard the aliquot and resume the procedure
with a clean pipet. Transfer the aliquot to the reservoir. Keep the Up of the pipet
near the surface of the isopropanol. Filter rapidly under vacuum. ~, Do'hot wash the
sides of the reservoir. Leave the vacuum on for a time sufficient to dry the filter.
Release the vacuum and remove the .filter with forceps. .
46
-------
2.4.6.2 Analysis of .Calibration Standards
1. Mount each filter on a flat holder. Perform step scans on selected diagnostic
reflections of the standards and reference specimen using the procedure outlined in
Section 2.4.5.4, step 12, and the same conditions as those used for the samples.
«
2. Determine the normalized intensity for each peak measured, I°tJ, as outlined in
Section 2.4.5.4, step 14. s
2.4.7 Calculations
For each asbestos reference material, calculate the exact weight deposited on each
standard filter from the concentrations of the standard suspensions and aliquot volumes.
Record the weight, w, of each standard. Prepare a calibration curve by regressing 1° ., on
w. Poor reproducibility (±,15 percent RSD) at any given level indicates problems in the
sample preparation technique, and a need for new standards. The data should fit a straight-
line equation.
Determine the slope, m, of the calibration curve in counts/microgram. The intercept,
b, of the line with the f ° , axis should be approximately zero. A large negative intercept
indicates an error in determining the background, This may arise from incorrectly measuring
the baseline or from interference by another phase at the angle of background measurement.
A large positive intercept indicates an error in determining the baseline or that an impurity is
included in the measured peak.
Using the normalized intensity, I . . for the attenuated silver peak of a sample, and
the corresponding normalized intensity from the unattenuated silver peak t°A , of the sample
Ag
filter, calculate the transmittance, T, for each sample as follows:27'21
Determine the correction factor, f(T), for each sample according to the formula:
47
-------
x ' ID
1 — *T»XV
where
R = sin
sin 6a
6At = angular position of the measured silver peak (from Bragg's Law), and
0. = angular position of the diagnostic asbestos peak.
Calculate the weight, W,, in micrograms, of the asbestos material analyzed for in each
sample, using the absorption corrections:
faf(t) - b
a m
Calculate the percent composition, Ps, of each asbestos mineral analyzed for in the parent
material, from the total sample weight, WT, on the filter:
V, (1 - .OIL)
p » —5 x 100
where
P, = percent asbestos mineral in parent material;
W, = mass of asbestos mineral on filter, in ^g;
WT = total sample weight on filter, in /xg;
L = percent weight loss of parent material on ashing and/or acid treatment (see Section
2.4.5.4).
48
-------
2.4,8 References
Klug, H. P. and L. E. Alexander, X-Ray Diffraction Procedures for
Polycrystalline and Amorphous Materials, 2nd ed., New York: John Wiley and
, Sons, 1979.
2. Azaroffj L. V. and M, J. Buerger, The Powder Method of X-Ray
Crystallography, New York: McGraw-Hill, 1958.
3. JCPDS-International Center for Diffraction Data Powder Diffraction Studies,
1601 Park Lane, Swarthmore, PA.
4. Campbell, W. J., C. W. Muggins, and A. G. Wylie, Chemical and Physical
Characterization of Amosite, Chrysotile, Crocidolite, and Nonfibrous Tremolite
for National Institute of Environmental Health Sciences Oral Ingestion Studies,
•t. U.S. Bureau of Mines Report of Investigation R18452, 1980.
5. Lange, B. A. and J. C. Haartz, Determination of microgram quantities of asbestos
by x-ray diffraction: Chrysotile in thin dust layers of matrix material, Anal.
Chem., 51(4):529-525, 1979.
^6. NIOSH Manual of Analytical Methods, Volume 5, U.S. Dept. HEW, August
1979, pp. 309-1 to 309-9.
7. Dunn, H.W. and J. H. Stewart, Jr., Determination of Chrysotile in building
materials by x-ray diffraetometry, Analytical Chemistry, 54 (7); 1122-1125, 1982.
8. Taylor, A., Methods for the quantitative determination of asbestos and quartz in
bulk samples using x-ray diffraction, The Analyst, 1 03(1231): 1009-1020, 1978.
9. Birks, L., M. Fatemi, J. V. Gilfrich, and E. T. Johnson, Quantitative Analysts of
Airborne Asbestos by X-Ray Diffraction, Naval Research Laboratory Report 7879,
Naval Research Laboratory, Washington, DC, 1975.
10. Asbestos-Containing Materials in School Buildings; A Guidance Document, U,
S. Environmental Protection Agency. EPA/OTS No. C00090, March 1979.
11. Krause, J. B. and W. H, Ashton, Misidentification of asbestos in talc, pp. 339-353,
In: Proceedings of Workshops on Asbestos: Definitions and Measurement
Methods (NBS Special Publication 506), C. C. Gravatt, P. D. LaFleur, and K. F.
Heinrich (eds.), Washington, DC: National Measurement Laboratory, National
Bureau of Standards, 1977 (issued 1978).
49
-------
12. Stanley, H. D., The detection and identification of asbestos and asbestiform minerals
in talc, pp. 325-337, In: Proceedings of Workshop on Asbestos: Definitions and
Measurement Methods (NBS Special Publication 506), C. C. Gravatt, P. D.
LaFleur, and K. F. Heinrich (eds.), Washington, DC: National Measurement
Laboratory, National Bureau of Standards, 1977 (issued 1978).
13. Rickards, A. L., Estimation of trace amounts of chrysotile asbestos by x-ray
diffraction, Anal. Chem., 44(11): 1872-3, 1972.
14. Cook, P. M., P. L. Smith, and D. G. Wilson, Amphibole fiber concentration and
determination for a series of community air samples: use of x-ray diffraction to
supplement electron microscope analysis. In: Electron Microscopy and X-Ray
Applications to Environmental and Occupation Health Analysis, P. A. Russell
and A. E. Hutchings (eds.), Ann Arbor: Ann Arbor Science Publications, 1977.
15. Rohl, A. N. and A. M. Langer, Identification and quantitation of asbestos in talc,
Environ. Health Perspectives, 9:95-109, 1974.
16. Graf, J. L., P. K. Ase, and R. G. Draftz, Preparation and Characterization of
Analytica-I Reference Materials, DHEW (NIOSH) Publication No. 79-139, June
1979. '
17. Haartz, J. C., B. A. Lange, R. G. Draftz, and R. F. Scholl, Selection and
characterization of fibrous and nonfibrous amphiboles for analytical methods
development, pp. 295-312, In: Proceedings of Workshop on Asbestos:
Definitions and Measurement Methods (NBS special Publication 506), C. C.
Gravatt, P. D. LaFleur, and K. F. Heinrich (eds.), Washington, DC: National
Measurement Laboratory, National Bureau of Standards, 1977 (issued 1978).
18. Personal Communication, A. M. Langer, formerly of Environmental Sciences
Laboratory, Mount Sinai School of Medicine of the City University of New York,
New York, NY, now of Brooklyn College, Brooklyn, N.Y.
19. Asbestos .in Buildings: Simplified Sampling Scheme for Friable Surfacing
Materials,- U.S. Environmental Protection Agency. EPA 560/5-85-030a, October
1985.
«
20. Langer, A.'M., M. S. Wolff, A. N. Rohl, and I. J. Selikoff, Variation of properties
of chrysotile asbestos subjected to milling, J. Toxicol. and Environ. Health,
t 4:173-188, 1978.
21. Langer, A. M., A. D. Mackler, and F. D. Pooley, Electron microscopical
investigation of asbestos fibers, Environ, Health Perspect., 9:63-80, 1974.
50
-------
22?f Occella, E, and G. Maddalon, X-ray diffraction characteristics of some types of
asbestos" in relation to different techniques of comminution, Med. Lavoro,
54(10):628-636, 1963.
23. Spumy, K. R.t W. Stober, H. Opiela, and G. Weiss, On the problem of milling and
ultrasonic treatment of asbestos and glass fibers in biological and analytical
applications, Am. Ind. Hyg. Assoc. J., 41:198-203, 1980.
24. Berry, L. G. and B. Mason, Mineralogy, San Francisco: W, H. Greeman & Co.,
1959.
25 Schelz, J. P., The detection of chrysotile asbestos at low levels in talc by differential
thermal analysis, Thermochimica Acta, 8:197-204, 1974.
26, Reference 1, pp. 372-374.
27. Leroux',-J., Staub-Reinhalt Luft, 29:26 (English), 1969.
28, Leroux, J. A., B. C. Davey, and A. Paillard, Proposed standard methodology for
'the evaluation of silicosis hazards, Am. Ind. Hyg. Assoc. J., 34:409, 1973.
2.5 Analytical Electron Microscopy
2.5,1 Applicability
Analytical electron microscopy (AEM) can often be a reliable method for the detection
and positive identification of asbestos in some bulk building materials, both friable and
nonfriable. The method is particularly applicable to bulk materials that contain a large
amount of interfering materials that can be removed by ashing and/or dissolution and contain
asbestos fibers that are not resolved by PLM techniques. Many floor tiles and plasters would
be included in this type of sample. In combination with suitable specimen preparation
techniques, the AEM method can also be used to quantify asbestos concentrations.
2.5.2 Range
The range is dependent on the type of bulk material being analyzed. The upper detection
limit is 100%, and "the lower detection limit can be as low as 0.0001 % depending on the
extent to which interfering materials can be separated during the preparation of AEM
51
-------
specimens, the sophistication of the AEM preparation, and the amount of labor expended on
AEM examination.
2.5.3 Interferences
The presence of a large amount of binder/matrix materials associated with fibers can
make it difficult to positively identify fibers as asbestos. The portion of the fiber examined
*
by either electron diffraction or energy dispersive x-ray analysis (EDXA) must be free of
binder/matrix materials.
2.5.4 Precision and Accuracy
The precision and accuracy of the method have not been determined.
2.5.5 Procedures
*
**
The procedures for AEM specimen preparation depend on the data required. In analysis
of floor tiles, the weighed residue after removal of the matrix components (see Section 2.3,
Gravimetry) is often mostly asbestos, and the task is primarily to identify the fibers. In this
situation "the proportion of asbestos in the residue can be estimated by AEM and this estimate
can be used to refine the gravimetric result. For many floor tiles, the final result is not very
sensitive to errors in this estimation because the proportion of asbestos in the residue is very
high. For samples in which this is not the case, precise measurements can be made using a
quantitative AEM preparation, in which each grid opening of the specimen grid corresponds
to a known weight of the original sample or of a concentrate derived from the original
sample. Asbestos fibers on these grids are then identified and measured, using a fiber
counting protocol which is directed towards a precise determination of mass concentration.
This latter procedure is suitable for samples of low asbestos concentration, or for those in
which it is not possible to remove a large proportion of the matrix material.
2.5.5.1 AEM Specimen Preparation for Semi-Quantitative Evaluation.
The residual material from any ashing or dissolution procedures (see Section 2.3) used
(usually trapped on a membrane filter) should be placed in a small,volume of ethanol or
another solvent such as acetone or isopropyl alcohol, in a disposable beaker, and dispersed
52
-------
by treatment in an ultrasonic bath. A small volume of this suspension (approximately 3/il)
should be pipetted onto the top of a carbon-coated TEM grid. The suspension should be
allowed to dry under a heat lamp. The grid is then ready for examination.
• ,
Samples that are not conducive to ashing or dissolution may also be prepared in this way
for.AEM analysis. A few milligrams of the sample may be ground in a mortar and pestle or
milled, dispersed in ethanol or another solvent using an ultrasonic bath, and pipetted onto a
grid as described previously.
2.5.5.2 AEM Specimen Preparation for Quantitative Evaluation
The objective of this preparation is to obtain a TEM grid on which a known weight of
the bulk sample is represented by a known area of the TEM grid. A known weight of the
bulk sample, or of the residue after extraction, should be dispersed in a known volume of
distilled£water. Aliquots of this dispersion should then be filtered through 0.22 pm pore-size
MCE or 0.2 pm pore-size PC filters, using filtration techniques as described for analysis of
water samples.1 In order to obtain filters of appropriate paniculate loading for AEM
analysis, it may be necessary to perform serial dilutions of the initial dispersion. TEM grids
should then be prepared from appropriately-loaded filters, using the standard methods.2
Determination of the mass concentration of asbestos on the TEM grids requires a
different fiber counting protocol than that usually used for determination of numerical fiber
concentrations. Initially, the grids should be scanned to determine the dimensions of the
largest asbestos fiber or fiber bundle on the specimens. The volume of this fiber or bundle
should be calculated. The magnification of the AEM should be set at a value for which the
length of this fiber or bundle just fills the fluorescent screen. Asbestos fiber counting should
then be continued at this magnification. The count should be terminated when the volume of
the initial large fiber or bundle represents less than about 5% of the integrated volume of all
asbestos fibers detected. This counting strategy ensures that the fiber counting effort is
directed toward those fibers which contribute most to the mass, and permits a precise mass
concentration value to be obtained.
53
-------
2,5.5,2.1 Identification
To document the positive identification of asbestos in a sample, the analyst should record
the following physical properties: morphology data, electron diffraction data, EDXA data,
and any other distinguishing characteristics observed. For fibrous structures identified as
nonasbestos, the unique physical property or properties that differentiate the material from
asbestos should be recorded.
The purpose of the identification data collected is to prevent or limit false negatives and
false positives. This can be accomplished by having a system for measuring and recording
the d-spacings and symmetry of the diffraction patterns, determining the relative abundance
of the elements detected by EDXA, and comparing these results to reference data. The
laboratory should have a set of reference asbestos materials from which a set of reference
diffraction patterns and x-ray spectra have been developed. Also, the laboratory should have
available reference data on the crystallography and chemical composition of minerals that
might analytically 'interfere with asbestos.
t *,
2.5.6' References.
1. Chatfield, E.J., and M. j. Dillon, Analytical Method for Determination of
Asbestos Fibers in Water, EPA-600/4-83-043. U.S. Environmental Protection
Agency Environmental Research Laboratory, 1983.
2. Environmental Protection Agency's Interim Transmission Electron Microscopy
Analytical Methods—Mandatory and Nonmandatory—and Mandatory Section to
Determine Completion of Response Actions, Appendix A to subpart E, 40 CFR
part 763.
2.6 Other Methodologies
*"*,
Additional analytical methods (e.g. Scanning Electron Microscopy) may be applicable for
some bulk materials. However, the analyst should take care to recognize the limitations of
any analytical method chosen. Conventional SEM, for example, cannot detect small
*
diameter fibers (~ < 0.2fim), and cannot determine crystal structure. It is, however, very
* i
useful for observing surface features in complex particle matrices, and for determining
elemental compositions.
54
-------
3.0 QUALITY CONTROL/QUALITY ASSURANCE OPERATIONS- PLM
*
A program to routinely assess the quality of the results produced by the PLM laboratory
must be developed and implemented. Quality Control (QC) is a system of activities whose
purpose is to control the quality of the product or service so that it meets the need of the
users. This also includes Quality Assessment, whose purpose is to provide assurance that
the overall quality control is being done effectively. While the essential elements of a quality
control system are described in detail elsewhere,U-J-4-5-6 only several of the elements will be
discussed here. Quality Assurance (QA) is comprised of Quality Control ana Quality
Assessment and is a system of activities designed to provide assurance that a product or
service meets defined standards of quality.
V*-
The"purpose of the Quality Assurance program is to minimize failures in the analysis of
materials prio,r to submitting the results to the client. Failures in the analysis of asbestos
materials include false positives, false negatives, and misidentification of asbestos types.
False positives result from identification or quantitation errors. False negatives result from
identification, detection, or quantitation errors.
For'-the stereomicroscopic and PLM techniques, the quality control procedures should
characterize the accuracy and precision of both individual analysts and the techniques.
Analysts should demonstrate their abilities on calibration materials, and also be checked
routinely on the analysis of unknowns by comparison with results of a second analyst. The
limitations of the stereomicroscopic and PLM techniques can be determined by using a
second analytical technique, such as gravimetry, XRD, or AEM. For example,
stereomicroscopic and PLM techniques can fail in the analysis of floor tiles because the
asbestos*'fibers in the sample may be too small to be resolved by light microscopy. An XRD
or AEM analysis is not subject to the same limitations, and may indicate the presence of
asbestos in the sample.
The accuracy, precision, and detection limits of all analytical techniques described in this
method are dependent on the type of sample (matrix components, texture, etc.), on the
preparation of the sample (homogeneity, grain size, etc.), and the specifics of the method
(number of point counts for PLM, mass jof sample for gravimetry, counting time for XRD,
55
-------
etc.). These should be kept in mind when designing quality control procedures and
characterizing performance, and are variables that must be tracked in the quality assurance
system.
3.1 Genera! Considerations
3.1.1. Training
'Of paramount importance in the successful use of this or any other analytical method is
the well-trained analyst. It is highly recommended that the analyst have completed course
work in optical mineralogy on the collegiate level. That is not to say that others cannot
successfully use this method, but the classification error rate7 may, in some cases, be directly
attributable to level of training. In addition to completed course work in optical mineralogy,
specialized course work in PLM and asbestos identification by PLM is desirable. Experience
is as important as education, A good laboratory training program can be used in place of
course work. Analysts that are in training and not yet fully qualified should have all
analyses checked by a qualified analyst before results are released. A QC Plan for asbestos
*
identification would be considered incomplete without a detailed description of the analyst
training program, together with detailed records of training for each analyst.
3.1.2 Instrument Calibration and Maintenance
Microscope alignment checks (alignment of the polarizer at 90° with respect to the
analyzer, and coincident with the cross-lines, proper orientation of the slow vibration
direction of the Red I compensator plate, image of the field diaphragm focussed in the plane
of the specimen, centering of the central dispersion staining stop, etc.) should be performed
with sufficient frequency to ensure proper operations. Liquids used for refractive index
determination and those optionally used for dispersion staining should have periodic
* - .
refractive index checks using a refractometer or known refractive index solids. These
calibrations must be documented. '
Microscopes and ancillary equipment should be maintained daily. ~ It is recommended that
at least.once per year each microscope be thoroughly cleaned and re-aligned by a
professional microscope service technician. Adequate inventories of replaceable parts
'.'-•'• 56 ••' " ."•:?.•"•'-''•-' • '' -
-------
(illumination lamps, etc.) should be established and ma'mtained. All maintenance must be
documented.
3.2 Quality Control of Asbestos Analysis
3.2.1 Qualitative Analysis
All analysts must be able to correctly identify the six regulated asbestos types (chrysotile,
amosite, crocidolite, anthophyllite, actinolite, and tremolite) using combbied
stereomicroscopic and PLM techniques. Standards for the six asbestos types listed are
available from NIST, and should be used to train analysts in the measurement of optical
properties and identification of asbestos. These materials can also be used as identification
standards«"for XRD and AEM.
•Identification errors between asbestos types (e.g. reporting amosite when tremolite is
present) implies that the analyst cannot properly determine optical properties and is relying
on morphology as the identification criteria. This is not acceptable. Each analyst in the lab
should prate his or her proficiency in identifying the asbestos types; this can be checked
*
through use of calibration materials (NVLAP proficiency testing materials, materials
characterized by an independent technique, and synthesized materials) and by comparing
vesults v.'ith another analyst. The identification of all parameters (e.g. refractive indices,
birefringence, sign of elongation, etc.) leading to the identification should fall within control
limits determined by the laboratory. In addition, a subset of raateriais should be analyzed
using another technique to confirm the analysis.
As discussed earlier, the qualitative analysis is dependent upon matrix and asbestos type
and texture. Therefore, the quality assurance system should monitor for samples that are
difficult to analyze and develop additional or special steps to ensure accurate characterization
of these materials. When an analyst is found to be out of the control limits defined by the
laboratory, he or she should undergo additional training and have confirmatory analyses
performed on all samples until the problem has been corrected.
57
-------
3.2.2 Quantitative Analysis
The determination of the amount of asbestos in a sample can be accomplished using the
various techniques outlined in this method. The mandatory stereomicroscopic and PLM
examinations provide concentrations in terms of volume, area, or weight, depending upon the
calibration procedure. Gravimetric and quantitative XRD techniques result in concentrations
in units of weight percent. Specific guidelines for determining accuracy and precision using
these techniques are provided in the appropriate sections of this method. In general,
however, the accuracy of any technique is determined through analysis of calibration
materials which are characterized by multiple independent techniques in order to provide an
unbiased value for the analyte (asbestos) in question. The precision of any technique is
determined by multiple analyses of the sample. The analyst is the detector for
stereomicroscopic and PLM techniques, as opposed lo gravimetric and XRD techniques, and
therefore must be calibrated as an integral part of the procedure.
As in the qualitative analysis, the laboratory should determine its accuracy and precision
for quantitative asbestos analysis according to the type of material analyzed and the technique
used for analysis. For example, the laboratory may determine that its analysts have a
problem with calibrated area estimates of samples containing cellulose and chrysotile and
therefore needs to make or find special calibration materials for this class of sample.
Calibration materials for quantitative analysis of asbestos are available through the Bulk
AsbestosJWLAP as proficiency testing materials for those laboratories enrolled in NVLAP.
In a repoj^ provided following a test round, the concentration of asbestos in each sample is
given in weight percent with 95%/95% tolerance limits, along with a description of the
major matrix components. Materials from other round robin and quality assurance programs
for asbestos analysis may not have been analyzed by independent techniques; the
concentrations may represent consensus PLM results that could be significantly biased.
Therefore, 'values from these programs should not be used as calibration materials for
quantitative analysis.
* *
Calibration materials for quantitative analysis can also be synthesized by mixing asbestos
and appropriate matrix materials, as described in Appendix C of this method. These
58
-------
Materials are usually simplifications of "real world" samples; therefore the accuracy and
t- *
precision determined from analysis of ihese materials are probably idea!.
Limits on permissible analytical variability must be established by the laboratory prior to
QC implementation. It is recommended that a laboratory initially be at 100% quality control
(all samples reanalyzed.) The proportion of quality control samples can later be lowered
gradually., as control indicates, to a minimum of 10%. Quantitative results for standards
includin'g the mean and error estimate (typically 95% confidence or tolerance intervals)
should be recorded. Over time these data can be used to help determine control limits for
quality control charts.
The establishment and use of control charts is extensively discussed elsewhere in the
literature. u-3-4-5 Several cautions are in order:
* Control charts are based on the assumption that the data are distributed normally.
Using rational subgrouping,' the means of the subgroups are approximately normally
distributed, irrespective of the distribution of the individual values in the subgroups.
Control charts for asbestos analysis are probably going to be based on individual
measurements, not rational subgroups. Check the data for normality before
•proceeding with the use of control chans. Ryan8 suggests a minimum of 50 analyses
* before an attempt is made to establish control limits. However, for this analysis,
consider setting "temporary" limits after accumulating 20-30 analyses of the sample.
• Include both prepared slides as well as bulk samples in your reference inventory.
• Make certain that sample quantities are sufficient to last, and that the act of sampling
will not alter the composition of the reference sample.
Data on analytical variability can be obtained by having analysts repeat their analyses of
samp|es and also by having different analysts analyze the same samples.
3.3 Interlaboratory Quality Control
The establishment and maintenance of an interlaboratory QC program is fundamental to
*
continued -assurance that the data produced within the laboratory are of consistent high
quality.1 Intralaboratory programs may not be as sensitive to accuracy and precision error,
especially if the control charts (see Section 3.2.2) for all analysts in the laboratory indicate
small percent differences. A routine interlaboratory testing program will assist in the
detection of internal bias and analyses may be performed more frequently thart proficiency
59
-------
testing. Arrangements should be made with at least two (preferably more) other laboratories
that conduct asbestos identification by PLM. Samples (the number of which is left to the
participating laboratories, but at least 4-10) representing the types of samples and matrices
routinely submitted to the lab for analysis should be exchanged with sufficient frequency to
determine intralaboratory bias. Both reference slides and bulk samples should be used.
Results of the interlaboratory testing program should be evaluated by each of the
participating laboratories and corrective actions, if needed, identified and implemented.
Since quantitation problems are more pronounced at low concentrations (< 5%), it would be
prudent to include approximately 30-50% from this concentration range in the sample
selection process.
3.4 Performance Audits
Performance audits are independent quantitative assessments of laboratory performance.
These audits are similar to the interlaboratory QC programs established between several
laboratories, but with a much larger cohort (the EPA Asbestos Bulk Sample Analysis Quality
Assurance Program had as many as 1100 participating laboratories). Participation in this
type of program permitted assessment of performance through the use of "consensus" test
materials, and served to assist in assessing the bias relative to individual interlaboratory, as
well as intralaboratory programs. Caution should be exercised in the use of "consensus"
quantitalion results, as they are likely to be significantly responsible for the propagation of
V
high bias in visual estimates. The current NIST/NVLAP9 for bulk asbestos laboratories
(PLM) does not use concensus quantitation results. Results are reported in weight percent
with a 95% tolerance interval. The American Industrial Hygiene Association (AIHA)10 also
conducts a proficiency testing program for bulk asbestos laboratories. Quantitation results
for this program are derived from analyses by two reference laboratories and PLM, XRD
and gravimetric analysis performed by Research Triangle Institute.
3.5 Systems Audits
Where performance audits are quantitative in nature, systems audits are qualitative.
Systems audits are assessments of the laboratory quality system as specified in the Laboratory
60
-------
Quality Assurance Manual. Such an audit might consist of an evaluation of some facet of the
QA Manual, or the audit may be larger in scope. For example, the auditor might request
specific laboratory data sheets which will be evaluated against written procedures for data
recording Ln the laboratory. Or, the auditor might request air monitoring or contamination '
control data to review for frequency of sampling, analysis methodology, and/or corrective
actions taken when problems were discovered. The audit report should reflect the nature of
the audit as well as the audit results. Any recommendations for improvement should also be
«j,
reflected in such a report.
3.6 References V-'
1. Quality Assurance for Air Pollution Measurement Systems. Volume I,
Principles. EPA-600/9-76-005, March, 1976.
2. Juran, J. and F. Gryna, Quality Planning Analysis, 2nd edition, McGraw-Hill,
Inc., 1980.
3. Taylor, J.R., Quality Control Systems, McGraw Hill, Inc., 1989.
4. Rajliff, T.A., The Laboratory Quality Assurance System, Van Nostrand Reinhold,
1990.
5. Taylor, J.K., Quality Assurance of Chemical Measurements, Lewis Publishers,
1987.
6. Bulk Asbestos Handbook, National Institute of Standards and Technology, National
Voluntary Laboratory Accreditation Program, NISTIR 88-3879, October 1988.
p
7. Harvey, B.W., "Classification and Identification Error Tendencies in Bulk Insulation
Proficiency Testing Materials," American Environmental Laboratory, 2(2), 4/90,
pp. 8-14.
8. Ryan, T.P., Statistical Techniques for Quality Improvement, John Wiley & Sons,
Inc., New York, 1989.
9. National Institute of Standards & Technology (NIST) National Voluntary Laboratory
Accreditation Program (NVLAP), Building 411, Room A124, Gaithersburg, MD
20899, telephone (301) 975-4016.
10. American Industrial Hygiene Association (AIHA), 2700 Prosperity Avenue, Suite
250, Fairfax, VA 22031, (703) 849-8888.
61
-------
APPENDIX A
Glossary Of Terms
-------
APPENDIX A. GLOSSARY OF TERMS
Accuracy - The degree of agreement of a measured value with the true or expected value.
Anisotropic - Refers to substances that have more than one refractive index (e.g. are
birefringent), such as nonisometric crystals, oriented polymers, or strained isolropic
substances.
Asbestiform (morphology) - Said of a mineral that is like asbestos, i.e., crystallized with the
habit of asbestos. Some asbestiform minerals may lack the properties which make
asbestos commercially valuable, such as long fiber length and high tensile strength.
With the light microscope, the asbestiform habit is generally recognized by the
following characteristics:
• Mean aspect ratios ranging from 20:1 to 100:1 or higher for fibers longer than
. Aspect ratios should be determined for fibers, not bundles.
• Very thin fibrils, usually less than 0.5 micrometers in width, and
* Two or more of the following:
- Parallel fibers occurring in bundles,
- Fiber bundles displaying splayed ends,
- Matted masses of individual fibers, and/or
- Fibers showing curvature
These characteristics refer to the population of fibers as observed in a bulk sample.
It-is not unusual to observe occasional particles having aspect ratios of 10:1 or less,
but it is unlikely that the asbestos component(s) would be dominated by particles
(individual fibers) having aspect ratios of <20:1 for fibers longer than Sum, If a
sample contains a fibrous component of which most of the fibers have aspect ratios of
<20:1 and that. do not display the additional asbestiform characteristics, by definition
the component should not be considered asbestos.
Asbestos - A commercial term applied to the asbestiform varieties of six different minerals.
The asbestos types are chrysotile (asbestiform serpentine), amosite (asbestiform
grunerite), crocidolite (asbestiform riebeckite), and asbestiform anthophyllite,
asbestiform tremolite, and asbestiform actinolite. The properties of asbestos that
caused it to be widely used commercially are: 1) its ability to be separated into long,
• thin, flexible fibers; 2) high tensile strength; 3) low thermal and electrical
conductivity; 4) high mechanical and chemical durability, and 5) highiheat resistance.
A-l
-------
of the specimen and the mounting medium are different; it is used to determine
refractive index.
Bias - A systematic error characterized by a consistent (non-random) measurement error.
Binder • With reference to a bulk sample, a component added for cohesiveness (e.g.
plaster, cement, glue, etc.).
Birefringence - The numerical difference between the maximum and minimum refractive
indices of an anisotropic substance. Birefringence may be estimated, using a
Michel-Levy chart, from the interference colors observed under crossed polarizers.
Interference colors are also dependent on the orientation and thickness of the grain,
and therefore are used qualitatively to determine placement in one of the four
categories listed below.
Qualitative Quantitative(N-n)
none 0.00 or isotropie
low £0.010
moderate 0.011-0.050
high > 0.050
Bulk Sample - A sample of building material taken for identification and quantitation of
asbestos. Bulk building materials may include a wide variety of friable and
nonfriable materials.
Bundle - Asbestos structure consisting of several fibers having 3 common axis of elongatio
Calibration Materials - Materials, such as known weight % standards, that assist in the
calibration of microscopists in terms of ability to quantitate the asbestos content of
balk materials.
Color - The color of a particle or fiber when observed in plane polarized light
Compensator - A device with known, fixed or variable retardation and vibration direction
used for determining the degree of retardation (hence the thickness or value of
birefringence) in an anisotropic specimen. It is also used to determine the sign of
elongation of elongated materials. The most common compensator is the first-ordei
red plate (530-55Qnm retardation),
Control Chart - A graphical plot of test results with respect to time or sequence of
measurement, together with.limits within which they are expected to lie when the
system is in a state of statistical control.
A-2
-------
Detection Limit - The smallest concentration/amount of some component of interest that
can be measured by a single measurement with a stated level of confidence.
Dispersion Staining (focal masking) - An optical means of imparting apparent or virtual
color to transparent substances by the use of stops in the objective back focal plane; ir
it is used to determine refractive indices.
Error - Difference between the true or expected value and the measured value of a quantity
or parameter.
Extinction - The condition in which an anisotropic substance appears dark when observed
between crossed polars. This occurs when the vibration directions in the specimen
are parallel to the vibration directions in the polarizer and analyzer. Extinction may
be complete .or incomplete; common types include parallel, oblique, symmetrical and
undulose.
Extinction Angle - For fibers, the angle between the extinction position and the position at
which the fiber is parallel to the polarizer or analyzer privileged directions.
Fiber - With reference to asbestiform morphology, a structure consisting of one or more
fibrils.
Fibril - The individual unit structure of fibers.
Friable -«Refers to the cohesiveness of a bulk material, indicating that it may be crumbled
or disaggregated by hand pressure.
Gravimetry - Any technique in which the concentration of a component is determined by
weighing. As used in this document, it refers to measurement of asbestos-containing
residues after sample treatment by ashing, dissolution, etc.
Homogeneous - Uniform in composition and distribution of all components of a material,
such that multiple subsamples taken for analysis will contain the same components in
approximately the same relative concentrations.
Heterogeneous - Lacking uniformity in composition and/or distribution of material;
components not uniform. Does not satisfy the conditions stated for homogenous;
e.g., layered or in clumps, very coarse grained, etc.
Isotropic - Refers to substances that have a single refractive index such as unstrained
glass, un-oriented polymers and unstrained substances in the isometric crystal system.
A-3
-------
Lamdn Zero (X0) - The wavelength (Xo) of the dispersion staining color shown by a
specimen in a medium; both the specimen and medium have the same refractive index
at that wavelength,
Matrix - Nonasbestos, nonbinder components of a bulk material. Includes such
components as cellulose, fiberglass, mineral wool, mica, etc.
Michel-Levy Scale of Retardation colors - A chart plotting the relationship between
birefringence, retardation and thickness of anisotropic substances. Any one of the
three variables can be determined if the other two are known.
Morphology - The structure and shape of a particle. Characterization may be descriptive
(platy, red-like, acicular, etc) or in terms of dimensions such as length and diameter
(see asbestiform).
Pleochroism - The change in cc-ior or hue of colored anisotropic substance when rotated
relative to the vibration direction of plane polarized light.
Point Counting - A technique used to determine the relative projected areas occupied by
separate components in a microscope slide preparation of a sample. For asbestos
analysis, this technique is used to determine the relative concentrations of asbestos
minerals to nonasbestos sample components.
Polarization Colors - Interference colors displayed by anisotropic substances between two
polarizers. Birefringence, thickness and orientation of the material affect the colors
and their intensity.
Precision - The degree of mutual agreement characteristic of independent measurements as
Uje- result of reputed application of the process under specified conditions. It is
concerned with tne variability of results,
»*v'
&
Reference- Materials - Bulk materials, both asbestos-con-alr.ing and nonasbestos-
containing, for which the components are well-dccumented as to identification and
quan Illation.
Refractive Index (index of refraction) - The ratio of the velocity of light in a vacuum
relative to the velocity of light in A mednius. It is expressed as n and varies with
wavelength and temperature.
Sign of Elongation - Referring to the location of the high and low refractive indices in an
elongated anisotropic substance, a specimen is described as positive when the higher
refractive index is lengthwise (length slow), and as negative when the lower refractive
index is lengthwise (length fast). l
A-4
-------
Standard Reference Material (SRM) - A reference material certified and distributed by the
National Institute of Standards and Technology.
Visual Estimate - An estimation of concentration of asbestos in a sample as compared to the
other sample components. This may be a volume estimate made during
stereomicroseopic examination and/or a projected area estimation made during
microscopic (PLM) examination.
A-5
-------
APPENDIX B
Apparatus For Sample Preparation And Analysis
-------
Bl.O INTRODUCTION
The following lists the apparatus and materials required and suggested for the methods of
sample preparation and analysis described in the test method.1>2-3
B2.0 STEREOMICROSCOPIC EXAMINATION
The following are suggested for routine stereomicroscopic examination.
t
• HEPA-filtered hood or class 1 biohazard hood, negative pressure
• Microscope: binocular microscope, preferably stereoscopic. 5-60X magnification
(approximate)
• Light source: incandescent or fluorescent
• Tweezers, dissecting needles, scalpels, probes, etc. (for sample manipulation)
• Glassine paper, glass plates, weigh boats, petri dishes, watchglasses, etc. (sample
containers)
The following are suggested for sample preparation.
•
• Mortar and pestle, silica or porcelain-glazed
• Analytical balance (readability less than or equal to one milligram) (optional)
• Mill or blender (optional)
B3.0 POLARIZED LIGHT MICROSCOPY
The laboratory should be equipped with a polarized light microscope (preferably capable
of Kohler or Kohler-type illumination if possible) and accessories as described below.
• Ocular(s) fefnocular or monocular with cross hair reticle, or functional equivalent, and
a magnification of at least 8X
t,%
• 10X, 20X, and 40X objectives, (or similar magnification)
B-l
-------
* 360-degree rotatable stage
* Substage condenser with iris diaphragm
* Polarizer and analyzer which can be placed at 90 degrees to one another, and can be
calibrated relative 10 the cross-line reticle in the ocular.
» Accessory slot for wave plates and compensators (or demonstrated equivalent).
* Wave retardation plate (Red I compensator) with approximately 550 nanometer
retardation, and with known slow and fast vibration directions.
• Dispersion staining objective or a demonstrated equivalent, (optional)
* Monochromatic filter (nD), or functional equivalent, (optional)
In addition, the following equipment, materials and reagents are required or
recommended,1
* NIST traceable standards for the major asbestos types (NIST SRM 1866 and 1867)
• Class I biohazard hood or better (see "Note", Section 2.2,5)
• Sampling utensils (razor knives, forceps, probe needles, etc.)
* Microscope slides and cover slips
* Mechanical Stage
• Point Counting Stage (optional)
• Refractive index liquids; 1.490-1.570,1.590-1.720 in increments of less than or equal
to 0.005; high dispersion, (HD) liquids are optional; however, if using dispersion
staining, HD liquids are recommended.
• Mortar and pestle
* Distilled water
• HC1, ACS reagent grade concentrated
B-2
-------
• Muffle furnace (optional)
• Mill or blender (optional)
• Beakers and assorted glassware (optional)
• Other reagents (tetrahydrofuran, amyl acetate, acetone, sodium hexametaphosphate,
etc.) (optional)
B4.0 GRAVIMETRY
The following equipment, materials, and reagents are suggested.
• ^Scalpels
• Crucibles, silica or porcelain-glazed, with lids
•* Muffle furnace - temperature range at least to 500°C, temperature stable to ± 10°C,
temperature at sample position calibrated to ± 10°C
• Filters, 0.4.-/xm pore size polycarbonate
*«
• Petri dishes -
•.
•
• Glass filtration assembly, including vacuum flask, water aspirator, and/or air pump
» **
• Analytical balance, readable to 0.001 gram
• Mortar and pestle, silica or porcelain-glazed
«
• Heat lamp or slide warmer
e Beakers and assorted glassware
•
• Centrifuge, bench-top
• .*Class I biohazard hood or better
• Bulb pipettes
•»
• Distilled water
• HC1, reagent-grade concentrated
B-3
-------
* Organic solvents (letrahydrofuran, amyl aceiate.etc)
• Ultrasonic bath
B5.0 X-RAY DIFFRACTION
Sample Preparation
Sample preparation apparatus requirements will depend upon the sample type under
consideration and the kind of XRD analysis to be performed.
• Mortar and pestle: agate or porcelain
• Razor blades
t
• Sample mill: Sn?.X, Inc., freezer mill or equivalent
Bulk sample holders
*
*
• .Silver membrane filters: 25-mm diameter, 0.45-^m pore size. Selas Corp. of
America, Flotronics Div., 1957 Pioneer Road, Huntington Valley, PA 19006
• Microscope slides
* Vacuum filtration apparatus: Gelman No. 1107 or equivalent, the side-arm vacuum
flask
• Microbalance
• Ultrasonic bath or probe: Model WHO, Ultrasonics, Inc., operated at a power
density of approximately 0.1 W/mL, or equivalent
* "
* Volumetric flasks: 1-L volume
• Assorted pipets
• Pipet bulb
• Nonserrated forceps
* Polyethylene .wash bottle
• Pyrex beakers: 50-mL volume
B-4
-------
• Desiccator
* Filter storage cassettes
• Magnetic stirring plate and bars
• Porcelain crucibles
• Muffle furnace or low temperature asher
* Class 1 biohazard hood or better
Sample Analysis
•
Sample analysis requirements include an x-ray diffraction unit, equipped with:
• Constant potential generator; voltage and mA stabilizers
* Automated diffractometer with step-scanning mode
* Copper target x-ray tube: high intensity; fine focus, preferably
* X-ray pulse height selector
* X-ray detector (with high voltage power supply): scintillation or proportional counter
• Focusing graphite crystal monochromator; or nickel filter (if copper source is used,
and iron fluorescence is not a serious problem)
• %Data output accessories;
f -Strip chart recorder
- Decade sealer/timer
V
• Digital printer
or
- PC, appropriate software and Laser Jet Printer
• Sample spinner (optional)
• Instrument calibration reference specimen: a-quartz reference crystal (Arkansas
quartz standard, 1180-147-00, Philips Electronics Instruments, Inc., 85 McKee Drive,
Mahwah, NJ 07430) or equivalent.
B-5
-------
Reagents, etc.
Reference' Materials - The list of reference materials below is intended to serve as a guide.
Every attempt should be made to acquire pure reference materials that are comparable to
sample materials being analyzed.
• Chrysolite: UICC Canadian, NIST SRM 1866 (UICC reference material available
from: UICC, MRC Pneumoconiosis Unit, Llandough Hospital, Penarth, Glamorgan,
CF61XW, UK); (NIST Standard Reference Materials available from the National
Institute of Standards and Technology, Office of Reference Standards, Gaithersburg,
MD 20899)
• Crocidolite: UICC, NIST SRM 1866.
* "Amosite": UICC, NIST SRM 1866.
• Anthophyllite-Asbestos: UICC, NIST SRM 1867
• Tremolite Asbestos: Wards Natural Science Establishment, Rochester, NY; Cyprus
Research Standard, Cyprus Research, 2435 Military Ave., Los Angeles, CA 900064
(washed with dilute HC1 to remove small amount of calcite impurity); Indian
tremolite, Rajasthan State, India; NIST SRM 1867.
* Actinolite Asbestos: NIST SRM 1867
Adhesive - Tape, petroleum jelly, etc. (for attaching silver membrane filters to sample
holders).
Surfactant - 1 Percent aerosol OT aqueous solution or equivalent.
i
Isopropanol - ACS Reagent Grade.
B6.0 ANALYTICAL ELECTRON MICROSCOPY
AEM equipment requirements will not be discussed in this document; it is suggested that
equipment requirements stated in the AHERA regulations be followed. Additional
information may be found in the NVLAP Program Handbook for Airborne Asbestos
Analysis.1
B-6
-------
- The following additional materials and equipment are suggested:
• ' Analytical balance, readable to 0.001 gram
• Ultrasonic bath
* Glass filtration assembly (25mm), including vacuum flask and water aspirator
• Mixed cellulose ester (MCE) filters (0.22^m pore size) or 0.2^cin pore size
polycarbonate filters
* MCE backing filters (Spm pore size)
• .Silica mortar and pestle
• Beakers - glass and disposable
* Pipettes, disposable, 1,5, and 10 ml
B7.0 REFERENCES
**
1. National Institute of Standards and Technology (NIST) National Voluntary Laboratory
Accreditation Program (NVLAP) Bulk Asbestos Handbook, NISTIR 88-3879, 1988.
2. Interim Method for the retermination of Asbestos m Bulk Insulation Samples,
U.S. E.P.A. 600/M4-82-020, 1982.
3. National Institute of Standards and Technology (NIST) National Voluntary Laboratory
Accreditation Program (NVLAP) Program Handbook for Airborne Asbestos Analysis,
NISTIR 89-4137, 1989.
B-7
-------
APPENDIX C
Preparation and Use of Bulk Asbestos
Calibration Standards
-------
Cl.O INTRODUCTION
Evaluation of the results from national proficiency testing programs for laboratories
analyzing for asbestos in bulk materials i idicates that laboratories have had, and continue to
*
have, problems with quantitation of asbestos content, especially with samples having a low
asbestos concentration.1 For such samples, the mean value of asbestos content reported by
laboratories may be four to ten times the true weight percent value. It is assumed that the
majority of the laboratories quantify asbestos content by visual estimation, either
stereomicroscopically or microscopically; therefore, the problem of quantitation must be
attributed to lack of or inadequate calibration of microscopists.
As caK'iration standards for asbestos-containing bulk materials are not currently
commercially available, laboratories should consider generating their own calibration
materials. This may be done rather easily and inexpensively.
C2.0 MATERIALS AND APPARATUS
Relatively pure samples of asbestos minerals should be obtained. Chrysotile, amosite and
crocidolite (SRM 1'866) and anthophyllite, tremolite and actinolite (SRM 1867) are available
from NIST. A variety of matrix materials are commercially available; included are calcium
carbonate, perlite, vermiculite, mineral wool/fiberglass, and cellulose. Equipment, and
materials needed to prepare calibration bulk materials are listed below.
* Analytical balance, readable to 0.001 gram
* Blender/mixer; multi-speed, ~ one quart capacity
, * Filtration assembly, including vacuum flask, water aspirator and/or air pump
(optional)
• HEPA-filtered hood with negative pressure
« Filters, 0.4ptm pc-e size polycarbonate (optional)
• Beakers and assorted glassware, weigh boats, petri dishes, etc.
• Hot/warm plate
C-l
-------
* Asbestos minerals
* Matrix materials
» Distilled water.
C3.0 MATERIAL FORMULATION PROCEDURES
The formulation procedure involves first weighing appropriate quantities of asbestos and
matrix material to give the desired asbestos weight percent. The following formula may be
used to determine the weights of asbestos and matrix materials needed to give a desired
weight percent asbestos.
WTa _WTm
Wa ~Wm
Where;
WTm = weight of asbestos in grams (to 0.001 gram)
WTm = weight of matrix materials in grams (to 0.001 gram)
Wa = weight percent asbestos
Wm = weight percent matrix
Example: The desired total weight for the calibration sample is — 10 grams containing 5%
asbestos by weight If 0.532 grams of asbestos are first weighed out, what corresponding
weight of matrix material is inquired?
WTa = 0.532 grams n ^ „_
Wa =5% ^5J2=WJm
Wm =95%
m *** Then: WTm = 10.108 grams
The matrix is then placed into the pitcher of a standard over-the-counter blender, the
pitcher being previously filled to approximately one-fourth capacity (8~10 ounces) with
distilled water. Blending is performed at the lowest speed setting for approximately ten
seconds which serves to disaggregate the matrix materiaL The asbestos is then added, with
additional blending of approximately 30 seconds, again at the lowest speed setting. Caution
should be taken not to overblend the asbestos-matrix mixture. This could result in a
significant reduction in the size of the asbestos fibers causing a problem with detection at
normal magnification during stereomicroscopic and microscopic analyses. Ingredients of the
C-2
-------
pitcher are then poured into a filtering apparatus, with thorough rinsing of the pitcher to
ensure complete material removal. After filtering, the material is transferred to a foil dish
which is placed on a hot plate. The material is covered and allowed to sit over low heat
until drying is .complete; intermittent stirring will speed the drying process. For fine-grained
matrix materials such as gypsum, calcium carbonate, clays, etc., the sample is not filtered
after the blending process. Instead, the ingredients in the pitcher are transferred into a senes
of shallow, glass (petri) dishes. The ingredients should be stirred well between each
pouring to minimize the possible settling (and over-representation) of some components. The
dishes are covered and placed on a hot plate until the contents are thoroughly dried. For
small quantities of any matrix materials (15 grams or less), air-drying without prior filtering
is generally very suitable for removing water from the prepared sample. For each material,
the final step involves placing all formulated, dried subsamples into a plastic bag (or into one
petri dish, for small quantities), where brief hand-mixing will provide additional blending and
help to break up any clumps produced during drying. AH operations should be performed
in a safety-hood with negative pressure.
C4.0 ANALYSIS OF MATERIALS
All formulations should be examined with the stereomicroscope to determine
homogeneity. Gravimetric analysis (ashing and/or acid dissolution) should be performed on
those materials containing organic and/or acid-soluble components. Matrix materials to
which no asbestos has been added should be analyzed by gravimetric analysis to determine
the amount of nonashable or insoluble materials that are present. Several subsamples of each
material should be analyzed by the gravimetric technique to provide information concerning
the uniformity of the prepared materials. Experience has shown that the previously described
formulation procedure results in relatively homogeneous materials.2
*"»
C4.1 Stereomicroscopic Analysis
.Visual estimation of sample components using the stereomicroscope is in reality a
comparison of the relative volumes of the components.3 Therefore, differences in specific
gravity between asbestos and matrix material must be considered and the relationship
C-3
-------
between weight percent and volume percent must be determined,4 Materials such as
expanded vermiculite, perlite, and cellulose have specific gravities significantly lower than
asbestos minerals. Table Cl lists the specific gravities for the three most commonly
encountered asbestos varieties and several common matrix materials.
TABLE Cl. SPECIFIC GRAVITIES OF ASBESTOS VARIETIES
AND MATRIX MATERIALS
Asbestos Type
Chrysolile
Amosite
Crocidolite.
Specific Gravity
2.6
3.2
3.3
Matrix Type
Calcium Carbonate
Gypsum
Perlite
Vermiculite
(expanded)
Mineral Wool
Fiberglass
Cellulose
Specific Gravity
2.7
2.3
-0.4
-0.3
-2.5
-2.5
-0.9
The conversion of weight percent asbestos to equivalent volume percent" asbestos is given
the following, formula:
by the following formula:
Wa
Ga x 100 = Va
Wa-h Wm
Ga Gm
where:
Wa = weight percent asbestos
' Ga = specific gravity of asbestos
• ^01 = weight percent matrix
Gm = specific gravity of matrix
. Va =. volume percent asbestos
C-4
-------
Example: Chrysotile and perlite have been combined to form a 5% asbestos
calibration standard, by weight. What is the equivalent volume
percent asbestos?
Wa = 5% _5_
Ga - 2.6 = M.
Wm = 95% 5 +
Gm = 0.4 2.6 0.4
Ga = 2.6 y 2.6 x !00 = 0.8%
Wm = 95% 5+95
Conversely, to convert volume percent asbestos to equivalent weight percent, the
following formula may be used.
(VaKGa) x 100 = Wa
(Va)(Ga)+(Vm)(Gm)
Vm = volume percent matrix
Example: A calibration standard consisting of amosite and cellulose is
estimated to contain 2% asbestos, by volume. What is the
equivalent weight percent asbestos?
Va = 2% w (2K3.2) x 100 = 6.77%
• Ga = 3.2 a (2)(3.2) + (98)(0.9)
Vm = 98%
, Gm = 0.9
Volume percentages should be calculated for all calibration materials prepared so that
visual estimates determined by examination with the stereomicroscope may be compared to
true volume concentrations.
Figure Cl illustrates the relationship between volume percent and weight percent of
chrysotile mixed with vermiculite and cellulose respectively. It should be noted that when
asbestos in a low weight percentage is mixed with matrix materials having low specific
gravities (vermiculite, perlite), the resulting volume concentration of asbestos is very low.
For example, a mixture containing three percent chrysotile by weight in a cellulose matrix
would result in a volume,percent asbestos of approximately 1.1%; in a vermiculite matrix,
- '• .,. " . ' -. • • . ', '• . •••'» •;"-,- ' - -.:
the resulting volume percent asbestos would be approximately 0.4%. In the latter case
especially, an analyst might possibly fail to detect the asbestos or consider it to be present in
only trace amounts.
• s
e-s
-------
.GO
40
i so
JS
60
I 20
10
X
X
.*
•-•-« « with vermiculite
*-*-* » with cellulose
4 . f
Volume % Chryaotil*
10
Figure Cl. Relationship between volume % and weight % of chrysotile mixed with
a)vermiculite and b) cellulose.
-------
C4.2 Microscopical Analysis (PLM)
The polarized light microscope may be used to quantify asbestos and oiher components of
a sample. Slide mounts are prepared from "pinch" samples of the calibration material and
asbestos content is determined by visual area estimate and/or point counting. Both of these
quantitation techniques are in fact estimates or measurements of the relative projected areas
of particles as viewed in two dimensions on a microscope slide. For quantitation results to
be meaningful, the following conditions should be met:
• The sample should be homogeneous for slide preparations, which are made from
small pinches of the sample, to be representative of the total sample.
» Slide preparation should have an even distribution of particles and approach a one
particle thickness (seldom achieved) to avoid particle overlap.
• AH materials used should be identified and specific gravities determined in order to
relate area percent to volume and/or weight percent.
* The size (thickness) relationship between matrix particles and asbestos fibers should
. be determined if the results based on projected area are to be related to volume and/or
* weight percent.
Particle characteristics can greatly affect the quantitation results obtained by visual area
estimation or point counting. Figure C2 illustrates three hypothetical particle shapes of
identical length and width (as viewed from above). Although the three-dimensional shape is
different, Ihe projected area is equal for all particles. The table accompanying Figure C2
presents data for each particle in terms of thickness, volume and projected area. It should be
noted that although the-projected areas may be equal, the volumes represented by the
particles may vary by a factor of 20(0.8 vs 16 cubic units). It is obvious that quantitation of
a sample consisting of a mixture of particles with widely ranging panicle thicknesses could
result in different results. For example, if a sample contained relatively thick bundles of
asbestos and a fine-grained matrix such as clay or calcium carbonate, the true asbestos
content (by volume) would likely be underestimated. Conversely, if a sample contained thick
"books'* of mica and thin bundles of asbestos, the asbestos content (by volume) would likely
be overestimated.
C-7
-------
0.1 unit
thick
As Viewed
Particle
A
.B
C
Thickness
0.1 units
2 units
2 units
Volume
0.8 cubic units
12. 6 cubic units
16 cubic units
Projected Area
8 sq. units
8 sq. units
8 sq. units
Note that although ail particles have the same projected area,
particle C volume is 20x that of particle A. -;
Figure C2. Relationship of projected ares to volume and thickness for three different particles
as viewed on a slide mount.
C-8
-------
Table C2 illustrates several examples of expected results from area estimates or point
counting of samples in which the asbestos fibers and matrix particles differ in thickness.
TABLE C2. RELATIONSHIP OF WEIGHT PERCENT, VOLUME PERCENT AND
PARTICLE THICKNESS TO QUANTITATION RESULTS
Composition of
Sample In Wt. %
1% Amosite
99% Calcium Carbonate
1% Amosite
99% Calcium Carbonate
1% Amosite
99% Calcium Carbonate
1% Amosite
99% Vermiculite
4 % Amosite
99% Vermiculite
1% Amosite
99% Vermiculite
•
1% Amosite
99% Vermiculite
Theoretical Vol.
% Asbestos
0.9
0.9
0.9
0,1
0.1
0.1
0.1
Thickness Factor*
(Matrix/Asbestos)
0.5
1
2
\
10
20
30
Expected Area %
0.4
0.9
1.8
0.1
1.0
2.0
2.9
Value represents the relationship between the mean thickness of the matrix particles
compared to the mean thickness of the asbestos particles.
It should be noted that it is not uncommon for matrix particle thickness to differ greatly
from asbestos fiber thickness, especially with matrix materials such as Vermiculite and
perlite; vermiculite and perlite particles may be 20 - 30 times as thick as the asbestos fibers.
The general size relationships between matrix particles and asbestos fibers may be
determined by scanning slide mounts of a sample. A micrometer ocular enables the
microscopist to actually measure particle sizes.
C-9
-------
Jf a thickness factor can be determined for a calibration sample of known volume
proportions of asbestos and matrix materials, an expected equivalent projected area asbestos
can be calculated using the following formula:
Va
Vm
T
where:
Va
Vm
T
Aa
x 100 = Aa
Va
true volume percent asbestos
true volume percent matrix
thickness factor (mean size matrix particle/mean size asbestos fiber)
expected projected area percent asbestos
Example: A calibration standard of known weight percent asbestos is
determined, by factoring in component specific gravities, to be
5.0% asbestos by volume. The matrix particles are estimated to
. be ten times thicker than the asbestos fibers. What would be the
expected projected area percentage of asbestos?
Va = 5%
Vm = 95%
T =10
Aa ='
x 100 = 34.5%
+ 5
10
Conversely, to convert projected area percent asbestos to equivalent volume percent,
the following formula may be used:
Aa
x 100 = Va
T(Am) + Aa
Where: Am =, projected area matrix
Example: A slide containing a subsample of an amosite/mineral wool,
calibration standard is determined by point counting to, have a
projected area asbestos of 18.6%. - If the mineralwcjQl =ftbers are
estimated to be six times the asbestos fibers, in diameter, what .
is the equivalent volume percent asbestos?
C-10
-------
Am = 81.4%
Aa - 18.6% (18.6) x 100 = 3.67%
T = 6 6(81.4) + 18.6
< Based on specific gravity values listed in Table 1C and on the
above volume asbestos determination, what is the equivalent
weight percent asbestos in the sample?
Va =. 3,67% ' ' (3.67X3.2) x 100 = 4.7%
Ga = 3t2 * (3.67)(3.2) + (96.33X2.5)
= .'96.33%
CS.O USE OF CALIBRATION STANDARDS FOR QA/QC
Once the materials have been formulated and thoroughly characterized by all techniques
to determine their suitability as calibration standards, a system for incorporating them into
the QA/QC program should be established. Someone should be designated (QA officer, lab /
supervisor, etc.) to control the distribution of standards and to monitor the analysis results/df
the microscopists. 'Both precision and accuracy may be monitored with the use of suitable
standard sets. /
Records such as range charts, control charts, etc. may be maintained for volume'
(stereomicroscopic estimates), area (PLM) estimates and point counts. For point founts and
area estimates, relatively permanent slides may be made using epoxy or Melt Mount *, Such
slides may be very accurately quantified over time as to point count values, and due to their
very long shelf life, may be used for QA/QC purposes almost indefinitely.
C6.0 REFERENCES
*
1. "Analysis Summaries for Samples used in NIST Proficiency Testing", National
Institute of Standards and Technology (NIST) National Voluntary Laboratory
Accreditation Program (NVLAP) for Bulk Asbestos, January 1989 to present.
2. Harvey, B. W., R, L. Perkins, J. G. Nickerson, A. J. Newland and M. E. Beard,
^Formulating Bulk Asbestos Standards", Asbestos Issues, April ,1991.
3. Perkins, R. L. and M. E. Beard, "Estimating Asbestos Content of Bulk Materials",
National Asbestos Council Journal, Vol. 9, No. 1, 1991, pp. 27-31.
4. Asbestos Content in Bulk Insulation Samples: Visual Estimates and Weight
Composition, U.S. Environmental Protection Agency 560/5-88-011, 1988.
c-n
-------
APPENDIX D
Special-Case Building Materials
-------
Asbestos laboratories are now called upon to analyze many types of bulk building
materials that are very difficult to characterize by routine PLM analysis. These materials are
dominantly nonfriable and can be grouped into the following categories:
• Gsmentitious Products (pipe, sheeting, etc.)
t
• Viscous Matrix Products (adhesives, cements, coatings, etc.)
» Vinyl Materials (vinyl floor tile, sheeting)
* Asphaitic Roofing Materials (shingles, roll roofing)
* Miscellaneous Products (paints, coatings, friction plates, gaskets, etc.)
Materials characterized by interfering binder/matrix, low asbestos content, and/or small
fiber size jnay require that additional sample treatment(s) and analysis be performed beyond
routine BJLM analysis. The sample treatment(s) required is(are) determined by the dominant
nonasbestos sample components (see Section 2.3, Gravimetry). Materials containing an
appreciable amount of calcareous material may be treated by dissolution with hydrochloric
acid. Samples containing organic binders such as vinyl, plasticizers, esters, asphalts, etc.
can be treated with organic solvents or ashed in a muffle furnace (preferred method) or low
temperature plasma asher to remove unwanted components. Materials containing cellulose,
synthetic organic fibers, textiles, etc. may also be ashed in a muffle furnace or low
temperature plasma asher.
The method chosen for analysis of a sample after treatment is dependent on asbestos
concentration and/or fiber size. An examination of the sample residue by PLM may disclose
asbestos if the fibers are large enough to be resolved by the microscope, but additional
analytical methods are required if the sample appears negative. Analysis by XRD is not
fiber-size dependent, but may be limited by low concentration of asbestos and the presence of
interfering mineral phases. . In addition, the XRD method does not differentiate between "
fibrous and nonfibrous varieties of a mineral. Analysis by AEM is capable of providing
positive identification of asbestos type(s) and semi-quantitation of asbestos content.
D-l
-------
The following flowchart illustrates a possible scheme for the analysis of special-case
building materials.
NOTE: Preliminary studies indicate that the XRD method is capable of detecting
serpentine (chrysolite) in floor tile samples without extensive sample preparation prior to
XRD analysis. XRD analysis of small, intact sections of floor tile yielded diffraction
patterns that confirmed the presence of serpentine, even at concentrations of -one percent
by weight. TEM analysis of these same tiles confirmed the presence of chrysotile asbestos.
With further investigation, this method may prove applicable to other types of nonfriable
materials.
D-2
-------
FLOWCHART FOR QUALITATIVE ANALYSIS OF SPECIAL CASE BUILDING
MATERIALS SUCH AS FLOOR TILES, ASPHALTIC MATERIALS, VISCOUS
MATRIX MATERIALS, ETC."
BULK SAMPLE
STEREOMICRQSCOPIC/PLM ANALYSIS
SAMPLE IS EXAMINED FIRST WITH A
STEREOMICROSCOPE
FOLLOWED BY EXAMINATION KITH PLM
y
ACM
(Asbestos is confirmed at
concentration >1% - considered ACK)
NON ACM
(Asbestos not detected or detected at
trace level - non ACH by PLH)
Confirmatory an»lyei» by alternative
analytical method! (XW5 and/or ACH)
considered neceijjftry
HOW-ACH
GRAVIHETKY
Gravimetric method* used to rex.iv*
interfarentsi residue nay be
analyzed by PLH
ACK
ACH
Sample residue analyzed by
XRD and/or AEK
NON-ACM
ACK
•Although thi* flowchart i» applicable to all bi'lk material!, it i» primarily intended to be used
with known problem materials that are difficult to analyze by PLH due to low a*bestoc concentration,
and/or »»all fiber size, and/or interfering binder/matrix. In addition to being qualitative, the
results may also be.semi-quantitative, it should not be assumed that all samples need to b*
analyzed by AEH and XRD. The flowchart simply illustrates options fcx methods of analysis
Alternate methods such as SEM may be applicable to sone bulk materials.
• «.$ COVKNMIVTPIUKTINCOmCI 19S3 -750 -0«2/ei)Z37
0-3
------- |