Steps to  5^^^

  LEAD SAFE
  Renovation, Repair
         and Painting
xvEPA
  United States
  Environmental Protection
  Agency
 1-800-424-LEAD

www.epa.gov/lead

-------

 Renovating, Repairing or Painting?

 Are you working on a home renovation, repair or painting project?

 Does the project involve a home built before 1978?

 If so, you need to know how to work safely with lead-based paint. This
 guide is designed to help contractors and homeowners plan for and
 complete a home renovation, repair or painting project using lead safe work
 practices. Lead safe work practices are a group of techniques that reduce
 the amount of dust  produced by renovation activities. When used correctly,
 they make the work area safer for workers and the home safe for residents
 when renovation is complete.  Following lead safe work practices will allow
 you to:

   • Set up the job  safely;

   •  Minimize the creation of dangerous lead dust; and

   •  Leave the work area clean and safe for residents after completing the
     job.
    Contractors, Painters, Landlords! If you are working"
    in a home or child-occupied facility built before
1978,  you are required to provide information about
lead-based paint to occupants and owners of homes,
and owners and parents of child-occupied facilities.
For more information, see page 33.
    Beginning in April 2010, renovation, repair and paint-
    ing contractors must be certified and use lead safe
work practices when working in homes built before 1978.
For more information, see page 6.

-------
                               h
Table of Contents
    Learn the Facts About Lead-Based Paint
    The Renovation, Repair and Painting Program Rule
    Other Federal and State Regulation
    Step 1: Determine if the Job Involves Lead-Sased Paint
    Step 2: Set It Up Safely
    Step 3: Protect Yourself
    Step 4: Minimize the Dust
    Step 5: Leave the Work Area mean
    Step 6: Control the Waste
    Step 7: Verify Work Completion with the Clean!
            Verification Procedure or Clearance

    Learn More About Lead Safety
    Other Resources
    Pre-Renovation EducationfRequiremeJts
    Shopping List

-------
                                             »
                  Learn the Facts  about
                  Lead-Based Paint
About half of homes built before 1978 have lead-based paint. The
likelihood of finding lead-based paint increases with the age of the home:

  • Two out of three of homes built between 1940 and 1960 have
    lead-based paint.

  • Nine out of ten homes built before 1940 have lead-based paint.
                     Older Homes are More Likely to
                       Contain Lead-Based Paint
m
i
«
o
X
    Between 1960-1977
    Betwsen 1940-1959
         Before 1940
                 nijg" '"ijj" -"IB;"
                           25%
               0%  10%  20%  30%  40%  50%  60% 70% 80% 90% 100%


                   Percentage of Homes Containing Lead-Based Paint
               Source. American Healtny Homes Sur/ey: Draft Final Report for Pe&' Rewav: Lead and Arsenic
                                 s Octooer 7. 2008
Lead-based paint may be found on any surface in the home—inside
or outside. When lead-based paint is disturbed during renovation,  repair
or painting activities, dangerous amounts of lead dust can be created.
Jobs such as demolition, window replacement, opening up walls, etc., can
also release accumulated lead dust into the home.  Even after a typical
renovation cleanup, dangerous levels  of lead dust can remain.

-------
                            '

Lead gets into the body when it is swallowed or breathed.

  • People, especially children, can swallow lead dust as they eat, play,
    and perform other ordinary hand-to-mouth activities.

  • People may also breathe in lead dust or fumes while they work
    on jobs that sand, scrape, burn, brush, blast or otherwise disturb
    painted surfaces that contain lead paint.

  • Additionally, pets may be poisoned by the same types of exposure
    to lead.

Once in the body, lead can have significant effects on
human health.

  • In children, lead poisoning damages the nervous system and
    causes developmental and behavioral problems that can affect
    them for their lifetime.

  • In adults, lead poisoning causes health and reproductive problems.
    Pregnant women are especially vulnerable to the effects of lead.

Research has shown that general residential  renovation activities
are associated with an increased risk of elevated lead levels in
children.
                                          By working
                                        safely you can
                                         help prevent
                                        lead exposure
                                        and poisoning.
                                        This guide tells
                                           you how.

-------
                         The Renovation,
                         Repair and Painting
    Environmental Protection
    Agency
This section summarizes requirements of EPA's Lead-Based Paint
Renovation, Repair and Painting (RRP) Program Rule for contractors,
and provides guidance to homeowners/occupants, so that each may
learn to properly address lead-based paint hazards associated with
renovation, repair and painting activities.

The RRP rule affects contractors, property managers and others who
disturb known or presumed lead-based paint during renovation. The
term renovation covers all activities done for compensation that disturb
painted surfaces including most repair, remodeling and maintenance
activities, such as window replacement, weatherization and demoli-
tion. The RRP rule applies to all renovation work performed in residential
houses,  apartments and child-occupied facilities such as schools and
day-care centers built before 1 978. Those affected by the RRP rule
should read the complete rule, which is available on EPA's Web site at:
http://www.epa.gov/lead/pubs/renovation.htm.

Training, certification, and work practice requirements in the Renovation,
Repair and Painting Rule are effective April 22, 2010. Pre-renovation
education requirements are effective now.

Requirements for Renovation Contractors Include:
Certification and  Training Requirements
  • All firms performing renovation, repair or painting work must
    become certified. This can be accomplished by applying to EPA or
    to the State, if it has an EPA-authorized renovation program, and
    paying a fee.
  • Firms must have one or more "Certified Renovators" assigned to
    jobs where lead-based paint  is disturbed. To become certified, a
    renovator must successfully complete an EPA or State-approved
    training course conducted by an EPA or State-accredited training
    provider.
  • All renovation workers must be trained. Renovation workers can be
    trained on-the-job by a Certified Renovator to use lead safe work
    practices, or they can become Certified Renovators themselves.

-------
                              '

Pre-Renovation Education Requirements
  • Contractors, property managers and others who perform renova-
    tions for compensation in residential houses, apartments, and child-
    occupied facilities built before 1978 are required to distribute EPA's
    Renovate Right lead hazard information pamphlet before starting
    renovation work to occupants and owners of homes, and owners
    and parents of child-occupied facilities. More information about
    pre-renovation education requirements can be found on page 33.
Work Practice Requirements

  •  Renovators must use work-area containment to prevent
     dust and debris from leaving the work area.
  •  Certain work practices are prohibited. Open-flame
     burning, using heat guns at  greater than 1,100 degrees
     Fahrenheit and the use of power tools without high-
     efficiency particulate air (HEPA) exhaust control (to collect
     dust generated) are prohibited.
  •  Thorough cleaning followed  by a cleaning verification procedure to
     minimize exposure to lead-based paint hazards are required.
  •  Generally, minor  repair and maintenance activities (less than 6
     square feet per interior room or 20 square feet per exterior project)
     are exempt from the work practices requirements. However, this
     exemption does  not apply to jobs involving window replacement or
     demolition, or that involve the use of any of the prohibited practices
     listed above.

-------
                             1

Exemption from the RRP Rule
The training, certification and work practice requirements do not apply
where the firm obtains a signed statement from the owner that all of the
following conditions are met:

  • The renovation will occur in the owner's residence;
  • No child under age 6 resides there;
  • No woman who is pregnant resides there;
  • The housing is not a child-occupied facility; and,
  • The owner acknowledges that the renovation firm will not be
    required to use the work practices contained in the rule.

Homeowners Working in Their Own Homes
The RRP rule applies only to renovations performed for compensation.
If you work on your own home, the rules do not apply. Even so, EPA
encourages homeowners to use lead safe work practices, in order to
protect themselves, their families, and the value of their homes.
Landlords Working in Their Own Property
Landlords receive rental payments and maintenance personnel in rental
property or child-occupied facilities receive wages or salaries derived
from rent payments. This is considered compensation under the RRP
rule. Therefore, renovation  and repair activities performed by landlords
or employees of landlords are covered by the rule.  Work performed by
landlords or their employees in pre-1978 housing and  child-occupied
facilities must be performed using lead safe work practices, if lead-based
paint or presumed lead-based paint is disturbed.

-------
                  Other Federal  and
                  State Regulations
The U.S. Department of Housing and Urban Development (HUD)
Lead Safe Housing Rule
HUD's Lead Safe Housing Rule (24 CFR Part 35) covers pre-1978
federally-owned or assisted housing and federally-owned housing that is
being sold. It does not cover child-occupied facilities outside of residen-
tial housing. The requirements of HUD's rule are similar to EPA's RRP
rule, but there are some differences in the details, including:

  • Exemptions. HUD's rule does not allow owners of federally-
    assisted housing to opt out of its requirements.

  • Training Requirements. HUD does not recognize on-the-job
    training. To conduct  lead  hazard control in federally-assisted
    housing, either all workers must have completed a HUD-approved
    course, or the crew must be supervised by a Certified Renovator
    who is also a Certified Lead Abatement Supervisor.

  • Minor Repair and Maintenance. HUD's definition of minor repair
    and maintenance that is exempt from its rule is different than EPA's
    (2 square feet interior and 20 square feet exterior or 10 percent of
    the surface area of a small building component type).
Other differences between the EPA and HUD rules (concerning paint
testing, prohibited practices, clearance testing and waste disposal) are
pointed out in the appropriate  places.
State and Local Regulations
Other state or local requirements that are different from or more stringent
than the federal requirements may apply. For example, federal law allows
EPA to authorize states to administer their own lead renovation program
in place of the federal lead program. Even in states without an authorized
lead renovation program, a state may promulgate its own rules that may
be different or go beyond the federal requirements.

For more information on the rules that apply in your state, please contact
the National Lead Information Center at 1-800-424-LEAD (5323) or
www.epa.gov/lead/nlic.htm.

-------
                  Determine  If the  Job
                  Involves  Lead-Based
                  Paint
Before you begin a job, consider whether lead-based paint will be
an issue.

Find Out the Age of the Home or Child-Occupied Facility.
The age of a home can tell you a lot about whether lead-based paint is
likely to be present.

  • If it was built before 1978, it may have lead-based paint.

  • The older the home, the greater the likelihood that lead is present in
    the paint and accumulated dust.

  • Consider when additions were built. Some parts of the home may
    have been built later than others. Later additions are less likely to
    contain  lead-based paint and  contaminated dust.

  • Lead-based paint may be found either inside or outside the home
    and is most common in kitchens or bathrooms and in high gloss
    paint on trim, such as on window sills, door frames, and railings.

Look for Information About Lead.
Information about lead-based paint in your home may be readily
available. Under a federal disclosure law, when a pre-1978 home is sold
or leased, the seller/landlord must provide information to the buyer/
tenant about any known lead-based paint. Homeowners should check
their records to see if they have information about lead-based paint and
share this information with anyone  performing work on the home.
10

-------


Consider Lead Testing.
If a home was built before 1978, you must either assume that lead-
based paint is present or have the work area tested for lead-based paint
before starting the job. There are two options for testing paint in a home
under the Renovation, Repair and Painting Rule:

   1.  Paint testing by a certified lead-based paint inspector or lead-
     based paint risk assessor—These licensed professionals conduct a
     surface-by-surface investigation for lead-based paint by collecting
     paint chips for laboratory analysis or by testing painted surfaces
     with an machine called an X-Ray Fluorescence Analyzer (XRF) which
     measures the amount of lead in the paint.

   2.  Paint testing by a Certified Renovator—Certified Renovators, at the
     request of the homeowner, can use EPA-recognized chemical spot
     test kits to test all painted surfaces affected by the renovation.

Note: HUD does not recognize testing by a Certified Renovator using
spot test kits. In housing covered by the HUD Lead Safe Housing Rule,
only the first option is allowed.

All surfaces affected by a renovation covered by the Renovation,
Repair and Painting Rule must either be tested for lead-based paint or
presumed to contain  lead-based paint.  Testing must include all affected
surfaces coated with  paint, shellac, varnish, stain, coating or even paint
covered by wallpaper, if it will be disturbed during the renovation work.
A report documenting the testing must  list the surfaces tested and the
surfaces which contain lead-based paint. If lead-based paint is present
on an affected surface, then the lead safe work practices described in
this pamphlet must be used on the job.

For a list of certified lead testing professionals in your area, contact the
National Lead Information Center at 1-800-424-LEAD (5323) or visit
http://cfpub.epa.gov/flpp.

Remember, if the home was built before 1978 and there is no information
available about the paint, renovators must presume lead-based paint is
present  and use the lead safe work practices described in this pamphlet.
Make sure everyone involved on  the job, including workers, supervisors
and residents, uses proper safety precautions.
                                                                11

-------
 CAUTIOM      Set  It  Up Safely
When you work on a job with lead-based paint, you should
separate the work area from the rest of the home. The goal of
proper setup of the work area is to keep dust in the work area and
non-workers out.

The work area is the area that may become contaminated during the
work. The size of the work area may vary depending on the method used
to disturb lead-based paint and the amount of dust and debris that is
generated as a result. Whenever lead-based paint is disturbed, the work
area must be protected by plastic sheeting applied to the floor, ground
or other applicable surfaces to prevent contamination of the home or
exterior, from dust generated by the work.

The Renovation, Repair and Painting Rule requires that the work area
be protected by plastic sheeting that extends a minimum of 6 feet in
all directions from the location where paint will be disturbed. The Rule
further requires that  protective plastic sheeting extend far enough from
the location of paint disturbance so that all dust or debris generated by
the work remains within the area protected by the plastic. The entire
portion of the home or exterior that is protected by plastic sheeting,
however large, is the work area.

Unauthorized persons and pets must be prevented from entering the
work area. This can  be accomplished by posting warning signs and by
establishing barriers around the work area such as barrier tape, fencing,
plastic barriers in doorways, etc.
12

-------
                             '

Shopping List
Here is a list of supplies and tools you will need to set up the work area
safely. These items are available in hardware, paint or garden supply stores.

Materials to Restrict Access and Cover the Floor/Ground
  a  Signs

  Q  Barrier tape, rope or fencing

  Q  Cones

  Q  Heavy duty plastic sheeting

  Q  Tape (masking, duct or painter's)

  a  Stapler

  Q  Utility knife or scissors

What To Do

To keep the dust in and people out of your work area, you will need to take
the steps below for inside or outside jobs. Some jobs create more dust
than  others and, therefore,  call for additional precautions.

For Inside Jobs

  •  Have occupants leave the room where the work will be done and
     have them stay outside of the work area until after the final cleanup.

  •  Place signs, barrier tape and/or cones to keep all non-workers,
     especially children, out of the work area. Keep pets out of the work
     area for their safety and to prevent them from tracking dust and debris
     throughout the home.  Signs should be in the primary language of
     the occupants and should say "Do Not Enter - Authorized Personnel
     Only" and "No Eating,  Drinking, or Smoking."
                                                             13

-------

    Remove furniture and belongings from the work area. These items
    may include: drapes, curtains, furniture,  rugs, etc. If an item is too
    large to move, cover it with heavy plastic sheeting and tape the
    sheeting securely in place.

    Use heavy plastic sheeting to cover floors in the work area, to a
    minimum of 6 feet from the area of paint disturbance. Secure with
    tape.

    Close all doors in the work area, including closet and cabinet doors,
    and cover with plastic sheeting. When the work area boundary
    includes a door used to access the work area, cover the door with
    two layers of protective sheeting as described here:

      •  Cut and secure one layer of
        sheeting to the perimeter of
        the doorframe. Do not pull the
        sheeting taut. Rather, create a
        few folds to leave slack at the
        top and bottom of the door
        before taping or stapling.

      •  Cut a vertical slit in the middle of
        the sheeting leaving 6" uncut at
        the top and bottom. Reinforce
        with tape.

      •  Cut and secure a second,
        overlapping layer of sheeting to
        the top of the door.

    Close and cover air vents in the work area. This will keep dust from
    getting into vents and moving through the home. You may need to
    turn off your HVAC system to prevent damage to the system.

    Put all  necessary tools and supplies on the  protective sheeting
    before you begin work to avoid stepping off the protective sheeting
    before the work  is complete.
14

-------
                              '

For Outside Jobs

  •  Keep non-workers away from the work area by marking it off with
     signs, tape and/or cones.

  •  Cover the ground and plants with heavy plastic sheeting to catch
     debris. The covering should extend at least 10 feet out from the
     building. Secure the covering to the exterior wall with a wood strip
     and staples, or tape.

  •  Close windows and doors within 20 feet of the work area to keep
     dust and debris from getting into the home.

  •  Move or cover any play areas that are within 20 feet of the work
     area.

  •  When working on the 2nd story or above,  extend the sheeting
     farther out from the base of the home and to each side of the area
     where paint is being disturbed.

  •  Vertical shrouding on scaffolding should be used if work is close
     to a sidewalk, street, or property boundary, or the building is more
     than three stories high.

  •  Avoid working in high winds if possible. The EPA Renovation, Repair
     and Painting Rule does not specifically address wind speed, but
     when the  wind is strong enough to move dust and debris, special
     precautions need to be taken to keep the work area contained.
     That may  mean creating a wind screen of plastic at the edge of
     the ground-cover plastic to keep dust and debris from migrating.
     Ultimately, you are responsible for preventing dust and debris from
     leaving the work area, so  take appropriate precautions when wind is
     a factor.

  •  Put all necessary tools and supplies on the protective sheeting
     before you begin work to  avoid stepping off the protective sheeting
     before the work is complete.
                                                                15

-------
                   Protect Yourself
Workers should protect themselves.
Without the right personal protective equipment, workers may ingest
or inhale lead from the job and may risk bringing lead from the worksite
home to their families. The following items are available through
hardware, paint, garden supply stores or other specialty suppliers.
Shopping List

  Q  Protective eye wear

  Q  Painter's hat

  Q  Disposable coveralls

  Q  Disposable N-1 00 rated respirator

  Q  Disposable latex/rubber gloves

  Q  Disposable shoe covers

What to  Do

Protect your eyes.
  • Always wear safety goggles or safety glasses when scraping,
    hammering, etc.

Keep clothes clean.

  • Wear disposable protective clothing covers. Disposable protective
    clothing covers can be stored in a plastic bag and reused if they are
    fairly clean and are not torn. Small tears can be repaired with duct
    tape.

  • At the end of the work period, vacuum off dust, and remove dispos-
    able protective clothing covers. Do not use compressed air to blow
    dust off disposable protective clothing covers or clothing.

  • Do not hug other people until you have taken off your work clothes.
    Then, wash your work clothes separately from family laundry.
16

-------
                             '
  • Wear disposable shoe covers to prevent the tracking of dust from
    the work area and to protect your shoes from exposure to dust.

  • Wear gloves to protect your hands and  prevent exposure to dust.

  • Wear a painter's hat to protect your head from dust and debris.
    These are easy to dispose of at the end of the day.

Wear respiratory protection.
When work creates dust or paint chips, workers should wear respiratory
protection, such as an N-100 disposable respirator, to prevent them from
breathing leaded dust.
Post a warning sign.
Post a sign at the work entrance reminding workers to avoid eating,
drinking and smoking in the work area.
Your sign should say:
  •  Warning

  •  Lead Work Area

  •  Poison

  •  No Smoking, Drinking or
     Eating
Wash up.
Workers should wash their hands and faces each time they stop
working. It is especially important to wash up before eating and at the
end of the day.

Note: OSHA rules may require employers to take further steps to  protect
the health of workers on the job.
   ) www.osha.gov/SLTC/lead/index.html.
                                                              17

-------
                                L.

                       Minimize  the Dust
As you work, your goal is to keep down the dust.
Remember that as you scrape, drill, cut, open walls, etc., you are
creating dust. You can keep dust down by using the right tools and
following some simple practices that minimize and control the spread of
dust. The following items are available through hardware, paint, garden
supply stores or other specialty suppliers.
Shopping  List
Materials for all jobs:
  Q Wet-dry sandpaper, sanding sponge

  Q Misting bottle or pump sprayer

  Q Heavy plastic sheeting

  Q Utility knife or scissors

  Q Masking tape, duct tape, or painters' tape

  Q High Efficiency Particulate Air (HEPA) vacuum cleaner (a special
    vacuum cleaner that can remove very small particles from floors,
    window sills, and carpets and not return them to the air)

  Q Heavy duty plastic bags

  Q Tack pads (large, sticky pads that help remove dust), paper towels,
    or disposable wipes

Other tools that may be needed:
  Q Low-temperature heat gun (under 1,100 degrees Fahrenheit)

  Q Chemical strippers without methylene chloride

  O Power tools with HEPA filter equipped vacuum attachments

-------
                              '

What To  Do

Use the right tools.
  • Use wet sanders and misters to keep down the dust created during
    sanding, drilling and cutting.
  • Use HEPA vacuum attachments on power sanders and grinders to
    contain the dust created by these tools.
  • When a heat gun is needed to remove paint, use a temperature
    setting below 1,100 degrees Fahrenheit.

Use work practices that minimize dust.
  • Mist areas before sanding,  scraping, drilling and cutting to keep the
    dust down (except within 1  foot of live electrical outlets).
  • Score paint with a utility knife before separating components.
  • Pry and pull apart components instead of pounding and
    hammering.
  • Keep components that are being disposed of in the work area until
    they are wrapped securely in heavy plastic sheeting or bagged  in heavy
    duty plastic bags. Once wrapped or bagged, remove them from the
    work area  and store them in  a safe area away from residents.

Control the spread of dust.
  • Keep the work area closed  off from the rest of the home.
  • Don't track dust out of the  work area:
      •  Stay in the contained work area and on the contained paths.
      •  Vacuum off suits when  exiting the work area so the  dust stays
        inside  the work area.
      •  Every  time you leave the plastic sheeting, remove your dispos-
        able shoe covers, and wipe or vacuum your shoes,  especially,
        the soles, before you step off the plastic sheeting. A large
        disposable tack pad  on the floor can help to clean the soles of
        your shoes.
  • Launder non-disposable protective clothing separately from family
    laundry.
                                                               19

-------

Do Not Use Prohibited Practices.
The Renovation, Repair and Painting Rule prohibits the use of some
dangerous work practices by contractors. These "Prohibited Practices"
are:

  • Open-flame burning or torching of lead-based paint.

  • The use of machines that remove lead-based paint through high-
    speed operation such as sanding, grinding,  power planing, abrasive
    blasting or sandblasting, unless such machines are used with a
    HEPA exhaust control.

  • Operating a heat gun on lead-based paint at temperatures greater
    than 1,100 degrees Fahrenheit.

In federally-assisted housing, HUD's rule prohibits additional
work practices:
  • Extensive dry scraping and sanding by hand.

  • Heat guns that char paint.

  • Paint stripping in a poorly ventilated space using a volatile paint
    stripper.
Note:  The EPA Renovation, Repair and Painting  Rule does not apply to
homeowners who  renovate their own property. However, because the
practices prohibited under the rules generate significant amounts of dust,
EPA recommends  that they be avoided by the do-it-yourself homeowner
also.
20

-------
                  Leave the Work
                  Area  Clean
The work area should be left clean at the end of every day and
especially at the end of the job. The area should be completely free of
dust and debris. The following cleaning supplies, tools, and equipment
are available in hardware, paint or garden supply stores.
Shopping List
    Heavy-duty plastic bags

    HEPA vacuum with attachments and a powered beater bar

    Masking tape, duct tape, or painters tape

    Misting bottle or pump sprayer

    Disposable wet-cleaning wipes or hand towels

    Detergent or general-purpose cleaner

    Mop and disposable mop heads

    Two buckets or one two-sided bucket with a wringer

    Shovel and rake

    Wet Mopping System

    Electrostatically charged dry cleaning cloths
                                                        21

-------

What To Do
On a daily basis, renovators and do-it-yourself homeowners
should:
  • Pick up as you go. Put trash in heavy-duty plastic bags.
  • Vacuum the work area with a HEPA vacuum cleaner frequently
    during the day and at the end  of the day.
  • Clean tools at the end of the day.
  • Wash up each time you take a break and before you go home.
  • Dispose of or clean off your personal protective equipment.
  • Continue to separate the work area from the rest of the home and
    remind residents to stay out of the area.
When the job is complete, renovators and do-it-yourself
homeowners should:
  • Remove plastic sheeting carefully, fold it with the dirty side in, tape it
    shut, and dispose of it.
  • Make sure all trash and debris, including building components, are
    disposed of properly.
  • Vacuum all surfaces, including walls, with a HEPA vacuum cleaner.
  • Mist and  scrub the work area with a general-purpose cleaner on a
    wet rag or mop, changing the  rinse water often until  dust and debris
    are removed.
  • Vacuum all surfaces again once they are dry.
  • Visually inspect your work. Look around the home, both inside and
    out. You should  not be able to see any dust, paint chips or debris.
  • Re-clean the area thoroughly if you find dust or debris.
22

-------
                   Control the  Waste
What to Do

Bag or wrap your waste at the work site and in the work area.
  • Collect and control all your waste. This includes dust, debris, paint
    chips, protective sheeting, HEPA filters, dirty water, clothes, mop
    heads, wipes, protective clothing, respirators, gloves, architectural
    components and other waste.

  • Use heavy plastic sheeting or bags to collect waste. Seal the bag
    securely with  duct tape. Consider double bagging waste to prevent
    tears.  Large components should be wrapped in protective sheeting
    and sealed with tape.

  • Bag and seal all waste before removing it from the work area.

  • Store all waste in a secure container or dumpster until disposal.

  • Limit on-site storage time.

  • Avoid transporting waste in an open truck or personal vehicle.
                                                           23

-------

Dispose of waste water appropriately.
  • Water used for cleanup should be filtered and dumped in a toilet
    if local rules allow. If not, collect it in a drum and take it with you.
    Never dump this water down a sink or tub, down a storm drain, or
    on the ground. Always dispose of waste water in accordance with
    federal, state and local regulations.

  • EPA's Web site has state information on solid and hazardous waste
    disposal. See the following link for futher information:
    http://www.epa.gov/epawaste/wyl/stateprograms.htm.

Be aware of waste disposal rules.
  • Because EPA considers most residential renovation and remodeling
    as "routine residential maintenance," most waste generated during
    these activities is classified as solid, non-hazardous waste, and
    should be taken to a licensed solid waste landfill. This is not the case
    for work done in commercial, public or other nonresidential child-
    occupied facilities, where waste may be considered  hazardous and
    require special disposal methods. See the following link for futher
    information: www.epa.gov/lead/pubs/fslbp.htm.
    Always check state and local requirements before disposing of
    waste. Some are more stringent than federal regulations.

-------
                           •\                (I
           Verify Work Completion with

               the Cleaning Verification

               Procedure or Clearance
When all the work is complete, and before interior space is reoccupied,
you need to determine whether it is a safe environment to live in.

For Regulated Renovators and Maintenance Personnel:
If the work was performed by a contractor or landlord, either cleaning
verification or clearance testing is required by the RRP Rule. (If the
housing receives federal assistance, clearance testing is required.) If the
cleaning verification procedure is chosen, an EPA certified renovator
must perform the cleaning verification procedure. If clearance is chosen,
a certified lead inspector, certified lead risk assessor, or certified lead
sampling technician must conduct clearance testing.

For Do-it-Yourselfers:
After visual  inspection in homes not receiving federal assistance, where
the homeowner has completed the work, the homeowner is not required
to conduct  a cleaning verification procedure or clearance, but EPA
strongly recommends that you choose one or the other to ensure that a
complete cleaning was accomplished.

Cleaning Verification Procedure
After completion of cleaning, the cleaning verification procedure is
performed by wiping all dust collection surfaces in the work area with
a wet, disposable cleaning cloth and comparing that cloth visually to a
cleaning verification card. Dust collection surfaces include window sills,
countertops and other large horizontal surfaces such as fireplace mantles
and built-in  shelving, and floors. Cleaning verification cards are available
from EPA by calling the National Lead Information Center at
1-800-424-LEAD (5323). Cleaning verification may only be performed
by an EPA Certified Renovator if renovations covered by the Renovation,
Repair and  Painting rule were performed.

Note: For exterior work, only a visual inspection for dust, paint
chips or debris is required.
                                                         25

-------

                J
                                (  ..
The cleaning verification procedure for window sills is described
below:
  • Each window sill in the work area is wiped using a single, wet,
    disposable cleaning cloth.
  • Once the entire window sill surface is wiped, the wipe is compared
    to the cleaning verification card. (See "Interpreting the Cleaning
    Verification Procedure" on page 27).

The cleaning verification procedure for countertops and floors is
described below:
  • Each countertop is wiped by the Certified Renovator using a wet
    disposable cleaning cloth:

      •  For smaller countertops and other horizontal surfaces such as
        fireplace mantles and built-in shelving with a total surface area
        less than 40 square feet— wipe the entire surface with a single
        wipe and compare to the cleaning verification card.

      •  Large area surfaces, such as large countertops and floors,
        have surface areas larger than 40 square feet— each of these
        large countertops and floors must be divided into roughly equal
        sections that are 40 square feet or less. Wipe each section
        separately using a new wet disposable cleaning cloth for each
        separate section. When conducting cleaning verification on
        floors, the wipe will be attached to the handle of a wet mopping
        system. The use of the wet mopping system handle allows the
        Certified Renovator to apply uniform pressure on the cleaning
        cloth. Each wipe is then compared to the cleaning verification
        card.
26

-------
                             '

Interpreting  the  Cleaning Verification
Procedure

  • Compare each wipe representing a specific surface section to
    the cleaning verification card. If the cloth used to wipe a surface
    section within the work area is cleaner than the example wipes on
    the cleaning verification card, then that surface section has been
    adequately cleaned.

  • If the cloth is not cleaner than the cleaning verification card, re-clean
    that surface section. Then use a new wet disposable cleaning cloth
    to wipe the surface section again.  If the second cloth is cleaner
    than the cleaning verification card, that surface section has been
    adequately cleaned.

  • If the second cloth is not cleaner than the cleaning verification card,
    re-clean the surface, wait for 1 hour or until the surface section has
    dried completely, whichever is longer.

  • Wipe the surface section with a dry electrostatic cleaning cloth. The
    cleaning verification procedure is now complete and the surface is
    considered clean.

  • When all of the surfaces in the work area have passed  comparison
    with the cleaning verification card,  or have completed the post-
    renovation cleaning verification, the project is complete and the area
    can be turned over to occupants unless the housing is receiving
    federal assistance, or state or local laws require dust clearance
    testing, in which case the project must pass dust clearance testing
    before the area can be turned over to occupants.
                                                              27

-------

Dust Clearance Testing
 Clearance testing is conducted by certified lead-based paint
 inspectors, certified lead risk assessors, or certified lead
 dust sampling technicians. For homes receiving federal
 assistance, the clearance testing must be done by a person
 independent of the  renovation firm.

  • Although  optional under the Renovation, Repair and Painting
    Rule, some states and localities may require clearance. Also, a
    homeowner may specifically request that a  clearance test be
    performed in their contract. In this case, clean up the work area
    and check your work, then contact a certified lead-based paint
    inspector, risk assessor or lead dust sampling technician to
    arrange for clearance testing.

  • HUD requires clearance testing after renovation or repair work in
    pre-78 homes receiving federal assistance,  which are regulated
    under the Lead Safe Housing Rule. Contractors must determine
    whether the home is federally-assisted. Federal assistance may
    be channeled through a state or local government, community
    development corporation or other similiar entity.

  • Clearance sampling for interior jobs will consist of a floor sample
    taken in each room where work was performed (to a maximum
    of four samples) and an additional sample on the floor outside
    the entry to the work area. Where window sills and window
    troughs were present in the work area, a window sill or window
    trough sample will be collected in each room where work was
    performed (to a maximum of four samples).

  • All clearance samples must be sent to an EPA- recognized
    dust-lead laboratory for analysis. You can view the list of
    laboratories at www.epa.gov/lead/pubs/nllap.htm.
    For exterior jobs, EPA, like HUD, requires only a visual
    assessment of the work area to pass clearance.

-------
                           '

Interpret the Clearance Sampling Results

The laboratory will report the amount of lead in the dust. A dust sample
at or above the following limits for lead is considered hazardous:

  • Floors: 40 micrograms per square foot

  • Window sills: 250 micrograms per square foot

  • Window troughs: 400 micrograms per square foot

If the laboratory report shows lead levels at or above these
thresholds, the home fails the dust wipe test. The home must be
cleaned and retested until compliance with these clearance limits is
achieved. Re-cleaning must be done by the contractor.

It is a good idea for homeowners to specify in the initial contract
that a dust clearance test will be done at the  end of the job and
that the contractor will be responsible for re-cleaning if the
home fails this test. No one besides the contractor and the clearance
examiner should enter the work area until the area has been cleaned.
                                                         29

-------
                    Learn  More About
                    Lead Safety
To learn more about lead safe work practices, contact the National Lead
Information Center at 1-800-424-LEAD (5323) and see the following link
http://www.epa.gov/lead/nlic.htm. The Center is the federal govern-
ment's  leading source of quality information on lead poisoning prevention
and lead hazards.

Take a Course.
Get trained in lead safety. Professional trainers and community colleges
in your  area may offer training. For information on courses, contact the
National Lead Information Center. One relevant course is:

  • Lead Safety For Renovation, Repair and Painting
    (EPA-740-R-09-001, February 2009). EPA and HUD developed this
    8 hour training course to instruct renovators,  painters and mainte-
    nance personnel how to work safely in homes with lead-based
    paint. The course is interactive and includes hands-on activities for
    practicing the skills workers need to  avoid  creating lead hazards in
    the homes where they work. More information can  be found at:
    http://www.epa.gov/lead/pubs/epahudrrmodel.htm.

Find Out About Local Rules and Resources.
The National  Lead Information Center can provide information on how to
contact your  state, local and/or tribal programs to get general information
about lead poisoning prevention.

  • Local health departments can provide information about local
    programs, including assistance for poisoned children.

  • State and tribal lead poisoning prevention or environmental protec-
    tion programs can provide information about the lead regulations
    that apply in your community and can tell you about possible
    sources of financial aid for reducing lead hazards. They  also may be
    able  to tell you about the costs and availability of individuals certified
    to test lead paint and/or lead  dust.

  • Building code officials can tell you the regulations that apply to the
    renovation and  remodeling work that you are planning.

-------
                             '

Access Additional Resource Materials.
The National Lead Information Center can also provide copies of the
following general reference and how-to guidance materials:

  • Renovate Right: Important Lead Hazard Information for Families,
    Child Care Providers and Schools (EPA-740-F-08-002, March
    2008).
    http://www.epa.gov/lead/pubs/renovaterightbrochure.pdf

  • Small Entity Compliance Guide to Renovate Right: A Handbook
    for Contractors, Property Managers and Maintenance  Personnel
    Working in Homes, Child Care Facilities and Schools Built Before
    1978. (EPA-740-F-08-003, December 2008).
    http://www.epa.gov/lead/pubs/sbcomplianceguide.pdf

  • Contractors: Lead Safely During Renovation (EPA 740-F-08-001,
    March  2008). This short pamphlet provides a quick summary of
    general information on lead safe work practices to contain, minimize
    and clean up dust.
    http://www.epa.gov/lead/pubs/contractor brochure.pdf

  • Protect Your Family from  Lead in Your Home (EPA 747-K-99-001,
    June 2003). This is a general information pamphlet on  lead-based
    paint, lead hazards, the effects of lead poisoning and steps you can
    take to protect your family.
    http://www.epa.gov/lead/pubs/leadpdfe.pdf

  • Lead Paint Safety: A Field Guide for Painting, Home Maintenance,
    and Renovation Work (HUD-1779-LHC, March 2001).  This guide
    gives step-by-step instruction on lead safe work practices for
    different jobs in the home.
    http://www.hud.gov/offices/lead/training/LBPguide.pdf
                                                             31

-------
                                                 .'
                   Other Resources
For other resources on lead, visit the following Web sites:

http://www.epa.gov/lead/ — EPA is playing a major role in addressing
residential lead hazards, including deteriorating lead-based paint, lead
contaminated dust and lead contaminated residential soil. This Web site
provides information about lead and lead hazards and provides some
simple steps to protect your family. It contains links to basic  information,
as well as more detailed information and documents on lead in the news,
rules and regulations, education and outreach materials, training, and
other lead links.

http://www.hud.gov/offices/lead/ — The U.S.  Department of Housing
and Urban Development's Office of Healthy Homes and Lead Hazard
Control (OHHLHC) is unique among federal agencies dealing with  lead-
hazards, as it is staffed to bring lead health science to bear directly upon
America's housing. The site will direct you to resources on lead paint
regulations, training, guidance/technical guidelines and compliance and
enforcement.

http://www.osha.gov/SLTC/lead/index.html — The mission of
the U.S. Department of Labor's Occupational Safety and Health
Administration (OSHA) is to assure the safety and health of America's
workers by: setting and enforcing standards;  providing training, outreach,
and education; establishing partnerships; and encouraging continual
improvements in workplace safety and health. OSHA has established the
reduction of lead exposure as a high strategic priority. This site contains
links to lead recognition, evaluation, compliance, and training resources.

http://www.cdc.gov/lead — The U.S. Department of Health and
Human Services Centers for Disease Control  and  Prevention (CDC)
are committed to achieving improvements in people's health. This  site
provides CDC's compiled information on lead and includes materials and
links for parents, health professionals, researchers, students and others
interested in the topic of lead. The key resources include fact sheets,
guidelines and recommendations and questions and answers.
32

-------
                 Pre-Renovation
                 Education
                 Requirements
The pre-renovation education requirements of the Renovation, Repair
and Painting Rule ensure that owners and occupants of pre-1978 homes
and child-occupied facilities are provided information about potential
hazards of lead-based paint exposure before renovations are begun.

Who is affected? The requirements apply to any person paid to do
work that disturbs paint in residential housing or child-occupied facilities
built before 1978. This includes residential rental property owners and
managers, general contractors and special trade contractors such as
painters, plumbers, carpenters and electricians.

What properties are affected? All residential properties and
child-occupied facilities built before 1978 are affected unless they meet
one of the exceptions listed below.

Are there any exceptions? The requirements do not apply to housing
designated for elderly or disabled persons (unless children under age 6
live there), zero-bedroom dwellings (studio apartments, dormitories, etc.),
housing determined to be free of lead-based paint by a lead-based paint
inspection, emergency renovations and repairs, and minor repairs that
disturb less than 6 square feet of paint on interior surfaces or less than
20 square feet of paint on exterior surfaces.

What are the requirements? The Renovation, Repair and Painting Rule
requires the distribution of the lead pamphlet Renovate Right: Important
Lead Hazard Information for Families, Child Care Providers and Schools
before the work starts.
  • In  residential housing, the pamphlet must be provided to both the
    owner and occupants, and the contractor is required to document
    the receipt or mailing of the brochure.
  • In  multi-family residential housing, the pamphlet must be distributed
    to each affected unit.
  • When common areas of multi-family residential housing are affected
    by work, the pamphlet may be delivered to each unit or a notice
    can be sent to each unit notifying them of the location and duration
    of the work and the location of information postings about lead
    hazards and the work to be performed.
  • In  child-occupied facilities, the pamphlet must be provided to the
    owner, to the responsible party and to parents.
                                                            33

-------

         Renovate
         Right
         Important Lead Hazard
       tame
„..«,.«cldn Import ante sobre Ic
rlesgos causados por el p4omo
farriiias.-proveedores de culda
Intanlll y eocudas
How do I get the pamphlet? The pamphlet is available from the
National Lead Information Center at 1-800-424-LEAD (5323).
Ask for the Renovate Right: Important Lead Hazard Information for
Families, Child Care Providers, and Schools pamphlet, or download it
at: http://www.epa.gov/lead/pubs/renovaterightbrochure.pdf.
Note: In federally-assisted housing, HUD requires notification to be
distributed to occupants within 15 days after lead-based paint or lead-
based paint hazards are identified in their unit (or common areas, if
applicable), and within 15 days after completion of hazard control work
in their unit or common areas.

-------
                   Shopping List
Set It  Up Safely
  O Signs
  Q Barrier tape or rope
  Q Cones
  Q Heavy duty plastic sheeting
  Q Masking tape, duct tape, or
    painters' tape
  a Stapler
  Q Utility knife or scissors
Minimize the  Dust
  Q Wet-dry sandpaper, sanding
    sponge
  Q Misting bottle or pump sprayer
  Q Chemical strippers without
    methylene chloride
  Q High Efficiency Particulate Air
    (HEPA) vacuum cleaner (a
    special vacuum cleaner that
    can remove very small particles
    from floors, window sills, and
    carpets)
  Q Heavy-duty plastic bags
  Q Tack pads (large, sticky pads
    that help remove dust), paper
    towels, or disposable wipes
  Q Low-temperature heat
    gun (under 1,100 degrees
    Fahrenheit)
  Q Chemical strippers without
    methylene chloride
  a Power tools with HEPA filter
    vacuum attachments
Protect Yourself
  Q Protective eyewear
  Q Painter's hat
  Q Disposable coveralls
  Q Disposable N-100 rated respi-
    rator
  Q Disposable latex/rubber gloves
  Q Disposable shoe covers
Clean the Work
Area
  Q Heavy-duty plastic bags
  Q HEPA vacuum cleaner
  Q Masking tape, duct tape, or
    painters' tape
  Q Misting bottle or pump sprayer
  Q Disposable wet-cleaning wipes
    or hand towels
  Q Detergent or general-purpose
    cleaner

-------
Prevent Lead  Exposure During
Renovation,  Repair, and Painting
      Understand that Renovation, Repair and Painting Jobs Can
      Create Hazards. People, especially children, may swallow the
lead dust or paint chips created during the job and get poisoned. Lead
poisoning has serious health effects.
      Read Renovate Right, EPA and HUD's Lead Hazard
      Information Pamphlet. Contractors are required by law to give
clients in pre-1978 homes and child-occupied facilities a copy of
Renovate Right. Renovate Right explains the danger of lead-based paint
and its associated hazards. You can get copies of Renovate Right by
calling 1-800-424-LEAD (5323) or you can download it at
http://www.epa.gov/lead/pubs/renovaterightbrochure.pdf.
      Use Lead-Safe Work Practices. Follow practices that will protect
      you and residents from exposure to lead. These practices may take
a small amount of additional time and money, but they are necessary to
protect children,  residents, workers and workers' families from exposure to
lead dust.
      Conduct Lead Testing Before and/or After the Work is
      Performed. Pre-job testing can identify any lead paint in the home
and allow workers to target lead safe work practices to the areas where
there is lead paint. Using the cleaning verification procedure or clearance
testing at the end of the job ensures that no dust has been left behind.
       Learn More About Lead. To learn more about working safely with
       lead, contact the National Lead  Information Center at
 1-800-424-LEAD (5323) or visit EPA's Web site at www.epa.gov/lead or
 HUD's Web site at www.hud.gov/offices/lead.
 2009, EPA-740-K-09-003
environmental Protection Agency, Office of Pollution Prev
3epf. of Housing and Urban Development, Office of Healt
inted with Vegetable Oil-Based Inks, Recycled Paper
                                          and Toxia
                                          nes and Lt
                                                  ' Hazard Control

-------