EPA Document #: EPA/600/R-05/053
METHOD 535. MEASUREMENT OF CHLOROACETANILIDE AND OTHER
ACETAMIDE HERBICIDE DEGRADATES IN DRINKING
WATER BY SOLID PHASE EXTRACTION AND LIQUID
CHROMATOGRAPHY/TANDEM MASS SPECTROMETRY
(LC/MS/MS)
Version 1.1
April 2005
J.A. Shoemaker
M.V. Bassett
NATIONAL EXPOSURE RESEARCH LABORATORY
OFFICE OF RESEARCH AND DEVELOPMENT
U. S. ENVIRONMENTAL PROTECTION AGENCY
CINCINNATI, OHIO 45268
535-1
-------
METHOD 535
1.
MEASUREMENT OF CHLOROACETANILIDE AND OTHER ACETAMIDE
HERBICIDE DEGRADATES IN DRINKING WATER BY SOLID PHASE
EXTRACTION AND LIQUID CHROMATOGRAPHY/TANDEM MASS
SPECTROMETRY (LC/MS/MS)
SCOPE AND APPLICATION
1.1 This is a liquid chromatographic (LC)/tandem mass spectrometric (MS/MS)
method applicable to the determination of the ethanesulfonic acid (ESA) and
oxanilic acid (OA) degradates of the chloroacetanilide and other acetamide
herbicides in finished drinking waters. The single laboratory Lowest
Concentration Minimum Reporting Level (LCMRL) has also been determined in
reagent water.1 The following compounds can be determined using this method:
Analyte
Acetochlor ESA
Acetochlor OA
Alachlor ESA
Alachlor OA
Dimethenamid ESA
Dimethenamid OA
Flufenacet ESA
Flufenacet OA
Metolachlor ESA
Metolachlor OA
Propachlor ESA
Propachlor OA
Chemical Abstracts Service (CAS)
Registry Number
187022-11-3
184992-44-4
142363-53-9
171262-17-2
205939-58-8
—
—
—
171118-09-5
152019-73-3
—
—
1.2 The Minimum Reporting Level (MRL) is the lowest analyte concentration that
meets Data Quality Objectives (DQOs) that are developed based on the intended
535-2
-------
use of this method. The lowest concentration MRL (LCMRL) is a single
laboratory determination of the lowest true concentration for which a future
recovery is expected, with 99% confidence, to be between 50 and 150% recovery.
The procedure used to determine the LCMRL is described elsewhere.1 Single
laboratory LCMRLs for analytes in this method range from 0.016-0.11 ug/L for
the ion trap instrument and 0.22 - 0.55 ug/L for the triple quadrupole instrument,
and are listed in Table 5.
1.3 Laboratories using this method are not required to determine the LCMRL for this
method, but must demonstrate that their laboratory MRL for this method meets
the requirements described in Section 9.2.4.
1.4 Detection limit (DL) is defined as the statistically calculated minimum
concentration that can be measured with 99% confidence that the reported value is
greater than zero.2 The DL is compound dependent and is dependent on
extraction efficiency, sample matrix, fortification concentration, and instrument
performance. Determining the DL for analytes in this method is optional
(Sect. 9.2.5). DLs for target analytes range from 0.0060 - 0.043 ug/L for the ion
trap instrument and 0.057 -0.11 ug/L for the triple quadrupole instrument, and are
listed in Table 5.
1.5 This method is intended for use by or under the supervision of analysts skilled in
solid phase extractions, LC/MS/MS analysis and the interpretation of LC/MS/MS
chromatograms and mass spectra.
2. SUMMARY OF METHOD
2.1 Analytes and surrogate are extracted and concentrated by passing a 250-mL water
sample through a solid phase extraction (SPE) cartridge containing 0.5 g of
nonporous graphitized carbon. The compounds are eluted from the solid phase
with a small quantity of methanol containing 10 mM ammonium acetate. The
methanol extract is then concentrated to dryness and reconstituted with 1 mL of
water containing 5 mM ammonium acetate. The analytes are chromatographically
separated by injecting an aqueous aliquot (100 uL) into an LC system equipped
with a reversed phase (Clg) column. After elution from the column, the analytes
are detected by liquid chromatography/tandem mass spectrometry (LC/MS/MS).
The concentration of each identified component is measured by an internal
standard procedure, i.e. relating the product ion response of that compound to the
product ion response of the compound that is used as an internal standard. A
surrogate analyte, whose concentration is known in every sample, is measured
with the same internal standard calibration procedure.
535-3
-------
3. DEFINITIONS
3.1 ANALYSIS BATCH - A set of samples that is analyzed on the same instrument
during a 24-hour period that begins and ends with the analysis of the appropriate
Continuing Calibration Check (CCC) standards. Additional CCCs may be
required depending on the length of the analysis batch and/or the number of field
samples.
3.2 CALIBRATION STANDARD (CAL) - A solution prepared from the primary
dilution standard solution and/or stock standard solution, internal standard(s), and
the surrogate(s). The CAL solutions are used to calibrate the instrument response
with respect to analyte concentration.
3.3 COLLISIONALLY ACTIVATED DISSOCIATION (CAD) - The process of
converting the precursor ion's translational energy into internal energy by
collisions with neutral gas molecules to bring about dissociation into product ions.
3.4 CONTINUING CALIBRATION CHECK (CCC) - A calibration standard
containing the target analytes, internal standard(s) and surrogate(s), which is
analyzed periodically to verify the accuracy of the existing calibration for those
analytes.
3.5 DETECTION LIMIT (DL) - The minimum concentration of an analyte that can
be identified, measured and reported with 99% confidence that the analyte
concentration is greater than zero. This is a statistical determination of precision
(Sect. 9.2.5), and accurate quantitation is not expected at this level.2
3.6 EXTRACTION BATCH - A set of up to 20 field samples (not including QC
samples) extracted together by the same person(s) during a work day using the
same lot of solid phase extraction devices, solvents, surrogate, internal standard
and fortifying solutions. Required QC samples include Laboratory Reagent
Blank, Laboratory Fortified Blank, Laboratory Fortified Sample Matrix, and either
a Field Duplicate or Laboratory Fortified Sample Matrix Duplicate.
3.7 FIELD DUPLICATES (FD1 and FD2) - Two separate samples collected at the
same time and place under identical circumstances, and treated exactly the same
throughout field and laboratory procedures. Analyses of FD1 and FD2 give a
measure of the precision associated with sample collection, preservation, and
storage, as well as laboratory procedures.
3.8 INTERNAL STANDARD (IS) - A pure analyte(s) added to a sample, extract, or
standard solution in known amount(s) and used to measure the relative responses
535-4
-------
of other target analytes and surrogates that are components of the same solution.
The internal standard must be an analyte that is not a sample component.
3.9 LABORATORY FORTIFIED BLANK (LFB) - An aliquot of reagent water or
other blank matrix to which known quantities of the target analytes and all the
preservation compounds are added in the laboratory. The LFB is analyzed exactly
like a sample, and its purpose is to determine whether the methodology is in
control, and whether the laboratory is capable of making accurate and precise
measurements.
3.10 LABORATORY FORTIFIED SAMPLE MATRIX (LFSM) - An aliquot of a
preserved field sample to which known quantities of the target analytes are added
in the laboratory. The LFSM is processed and analyzed exactly like a sample, and
its purpose is to determine whether the sample matrix contributes bias to the
analytical results. The background concentrations of the analytes in the sample
matrix must be determined in a separate sample extraction and the measured
values in the LFSM corrected for background concentrations.
3.11 LABORATORY FORTIFIED SAMPLE MATRIX DUPLICATE (LFSMD) - A
second aliquot of the field sample used to prepare the LFSM. The LFSMD is
fortified, extracted, and analyzed identically to the LFSM. The LFSMD is used
instead of the Field Duplicate to assess method precision when the occurrence of
target analytes are low.
3.12 LABORATORY REAGENT BLANK (LRB) - An aliquot of reagent water or
other blank matrix that is treated exactly as a sample including exposure to all
glassware, equipment, solvents and reagents, sample preservatives, internal
standard, and surrogates that are used in the analysis batch. The LRB is used to
determine if target analytes or other interferences are present in the laboratory
environment, the reagents, or the apparatus.
3.13 LOWEST CONCENTRATION MINIMUM REPORTING LEVEL (LCMRL) -
The single laboratory LCMRL is the lowest true concentration for which a future
recovery is expected, with 99% confidence, to be between 50 and 150% recovery.1
3.14 MATERIAL SAFETY DATA SHEET (MSDS) - Written information provided
by vendors concerning a chemical's toxicity, health hazards, physical properties,
fire, and reactivity data including storage, spill, and handling precautions.
3.15 MINIMUM REPORTING LEVEL (MRL) - The minimum concentration that can
be reported as a quantitated value for a target analyte in a sample following
analysis. This defined concentration can be no lower than the concentration of the
lowest calibration standard for that analyte and can only be used if acceptable
535-5
-------
quality control criteria for this standard are met. A procedure for verifying a
laboratory's MRL is provided in Section 9.2.4.
3.16 PRECURSOR ION - For the purpose of this method, the precursor ion is the
deprotonated molecule ([M-H]") of the target analyte. In MS/MS, the precursor
ion is mass selected and fragmented by collisionally activated dissociation to
produce distinctive product ions of smaller m/z.
3.17 PRIMARY DILUTION STANDARD (PDS) SOLUTION - A solution containing
the analytes prepared in the laboratory from stock standard solutions and diluted
as needed to prepare calibration solutions and other needed analyte solutions.
3.18 PRODUCT ION - For the purpose of this method, a product ion is one of the
fragment ions produced in MS/MS by collisionally activated dissociation of the
precursor ion.
3.19 QUALITY CONTROL SAMPLE (QCS) - A solution of target analytes of known
concentrations that is obtained from a source external to the laboratory and
different from the source of calibration standards. It is used to check laboratory
performance with externally prepared test materials.
3.20 STOCK STANDARD SOLUTION (SSS) - A concentrated solution containing
one or more target analytes prepared in the laboratory using assayed reference
materials or purchased from a reputable commercial source.
3.21 SURROGATE ANALYTE (SUR) - A pure analyte, which chemically resembles
target analytes and is extremely unlikely to be found in any sample. This analyte
is added to a sample aliquot in known amount(s) before processing and is
measured with the same procedures used to measure other sample components.
The purpose of the SUR is to monitor method performance with each sample.
4. INTERFERENCES
4.1 Interfering contamination may occur when a sample containing low
concentrations of compounds is analyzed immediately after a sample containing
relatively high concentrations of compounds. After analysis of a sample
containing high concentrations of compounds, a laboratory reagent blank should
be analyzed to ensure that accurate values are obtained for the next sample. In the
case of automated analysis, the analyst may not be aware of high concentration
samples until after an entire batch is analyzed. In this situation, the analyst should
carefully review data from samples analyzed immediately after high concentration
samples, and reanalyze them if necessary.
535-6
-------
4.2 Matrix interferences may be caused by contaminants that are co-extracted from
the sample. The extent of matrix interferences will vary considerably from source
to source, depending upon the nature of the water. Humic and/or fulvic material
is co-extracted by this method and high levels can cause enhancement and/or
suppression in the electrospray ionization source or low recoveries on the carbon
SPE. For this method, total organic carbon (TOC) is a good indicator of humic
content of the sample. See Section 13.4 for more details.
4.3 The carbon solid phase cartridges did not produce any interferences during
method development. However, brands and lots of carbon cartridges should be
tested to ensure that contamination does not preclude analyte identification and
quantitation. The analysis of laboratory reagent blanks can provide important
information regarding the presence or absence of such interferences.
4.4 Method interferences may be caused by contaminants in solvents, reagents
(including reagent water), sample bottles and caps, and other sample processing
hardware that lead to discrete artifacts and/or elevated baselines in the
chromatograms. All items such as these must be routinely demonstrated to be free
from interferences (less than 1/3 the MRL for each target analyte), under the
conditions of the analysis, by analyzing laboratory reagent blanks as described in
Section 9.3. Subtracting blank values from sample results is not permitted.
5. SAFETY
5.1 The toxicity or carcinogenicity of each reagent used in this method has not been
precisely defined; each chemical compound should be treated as a potential health
hazard, and exposure to these chemicals should be minimized. The laboratory is
responsible for maintaining a current awareness file of OSHA regulations
regarding the safe handling of the chemicals specified in this method. A reference
file of MSDSs should also be made available to all personnel involved in the
chemical analysis.
5.2 Pure standard materials and stock standard solutions of these compounds should
be handled with suitable protection to skin, eyes, etc.3"5
6. EQUIPMENT AND SUPPLIES (All specifications are suggested. Brand names and/or
catalog numbers are included for illustration only, and do not imply endorsement of the
product.)
6.1 GLASSWARE - All glassware must be meticulously cleaned. Wash glassware
with detergent and tap water, rinse with tap water, followed by reagent water. A
final rinse with solvents may be needed. In place of a solvent rinse, non-
535-7
-------
volumetric glassware can be heated in a muffle furnace at 400 °C for 2 hours.
Volumetric glassware should not be heated above 120 °C.
6.2 SAMPLE CONTAINERS - Amber glass bottles (250 mL or larger) fitted with
PTFE (polytetrafluoroethylene) lined screw caps.
6.3 VIALS - Amber glass autosampler vials with PTFE faced septa for storing
standards and extracts.
6.4 VOLUMETRIC FLASKS - Class A, various sizes used for preparation of
standards.
6.5 GRADUATED CYLINDERS - Various sizes.
6.6 MICRO SYRINGES - Various sizes.
6.7 BALANCE - Analytical, capable of accurately weighing to 0.0001 g.
6.8 DISPOSABLE PIPETTES - 1 mL, used to transfer sample extracts to
autosampler vials.
6.9 CONICAL COLLECTION TUBES -15 mL, or other glassware suitable for
collection of the eluent from the solid phase cartridge after extraction.
6.10 SOLID PHASE EXTRACTION (SPE) APPARATUS USING CARTRIDGES
6.10.1 SPE CARTRIDGES - 0.5 g, 6 mL SPE cartridges containing a nonporous
graphitized carbon sorbent phase (Supelclean ENVI-Carb SPE cartridges,
Supelco Catalog No. 57904 or equivalent).
6.10.2 VACUUM EXTRACTION MANIFOLD - A manual vacuum manifold
(Supelco Cat. No. 57030 and 57275 or equivalent) for cartridge
extractions, or an automatic/robotic sample preparation (Zymark Autotrace
SPE Workstation or equivalent) system designed for use with solid phase
extraction cartridges, may be used if all quality control requirements
discussed in Section 9 are met. Extraction and/or elution steps may not be
changed or omitted to accommodate the use of an automated system.
6.10.3 SAMPLE DELIVERY SYSTEM - Use of a transfer tube system (Supelco
"Visiprep"; cat. #: 57275 or equivalent), which transfers the sample
directly from the sample container to the SPE cartridge, is recommended.
Sample reservoirs, which attach to the cartridge, may be used, although
they hold only 75 mL at one time.
535-8
-------
6.10.4 LABORATORY OR ASPIRATOR VACUUM SYSTEM - Sufficient
capacity to maintain a vacuum of approximately 25 cm (10 in) of mercury.
6.11 EXTRACT CONCENTRATION SYSTEM - Extracts are concentrated by
blowdown with nitrogen using a water bath set at 60-65 °C (Meyer N-EVAP,
model 111, Organomation Associates, Inc. or equivalent). Other types of
evaporation/concentration equipment may be used as long as all QC requirements
in Section 9 are met.
6.12 LIQUID CHROMATOGRAPHY (LC)/TANDEM MASS
SPECTROMETER(MS/MS)/DATA SYSTEM
6.12.1 LC SYSTEM - Capable of reproducibly injecting up to 100-uL aliquots,
and performing binary linear gradients at a constant flow rate near the flow
rate used for development of this method, e.g., 0.4 mL/min. The use of a
column heater is required. During method development, the column was
heated to 65 °C to achieve adequate separation of alachlor ESA and
acetochlor ESA, although other temperatures may be used as long as the
resolution requirement in Section 9.10 is met. The LC must be capable of
pumping the water/methanol mobile phase without the use of a vacuum
degasser. Vacuum degassers will volatilize the ammonium acetate mobile
phase causing the analyte peaks to shift to earlier retention times over the
course of the analysis batch. Sparging the mobile phase prior to use for a
short time period (approximately 5 minutes) is acceptable.
6.12.2 LC/Tandem Mass Spectrometer - The LC/MS/MS must be capable of
negative ion electrospray ionization (ESI) near the suggested LC flow rate
of 0.4 mL/min. The system must be capable of performing MS/MS to
produce unique product ions (Sect. 3.18) for the target analytes within
specified retention time segments. A minimum of 20 scans across the
chromatographic peak is recommended to ensure adequate precision. Data
is demonstrated in Tables 5-9 using an ion trap mass spectrometer
(Finnigan LCQ Deca) and a triple quadrupole mass spectrometer
(Micromass Quattro Micro).
6.12.3 An interfaced data system is required to acquire, store, reduce, and output
mass spectral data. The computer software should have the capability of
processing stored LC/MS/MS data by recognizing an LC peak within any
given retention time window. The software must allow integration of the
ion abundance of any specific ion within specified time or scan number
limits. The software must be able to calculate relative response factors,
construct linear regressions or quadratic calibration curves, and calculate
analyte concentrations.
535-9
-------
6.12.4 ANALYTICAL COLUMN- An LC Clg column (2.1 x 100 mm) packed
with 5 um dp Clg solid phase particles (Agilent # : 79916OD-552 or
equivalent) was used on the triple quadrupole instrument. For the ion trap
instrument, an LC Clg column (2.1 x 200 mm) packed with 5 um dp Clg
solid phase particles (Agilent # : 79916OD-572 or equivalent) was used to
achieve more separation between target analytes. Any column that
provides adequate resolution, peak shape, capacity, accuracy, and
precision (Sect. 9) maybe used. The Clg columns employed in the method
development were used for over 10 months with no measurable
degradation due to the elevated column temperatures (60 to 70 °C).
7. REAGENTS AND STANDARDS
7.1 GASES, REAGENTS, AND SOLVENTS - Reagent grade or better chemicals
should be used. Unless otherwise indicated, it is intended that all reagents shall
conform to the specifications of the Committee on Analytical Reagents of the
American Chemical Society, where such specifications are available. Other
grades may be used, provided it is first determined that the reagent is of
sufficiently high purity to permit its use without lessening the quality of the
determination.
7.1.1 REAGENT WATER - Purified water which does not contain any
measurable quantities of any target analytes or interfering compounds
greater than 1/3 the MRL for each compound of interest.
7.1.2 METHANOL (CH3OH, CAS#: 67-56-1) - High purity, demonstrated to be
free of analytes and interferences (Fisher Optima grade or equivalent).
7.1.3 AMMONIUM ACETATE (NH4C2H3O2, CAS#: 631-61-8) -Highpurity,
demonstrated to be free of analytes and interferences (Sigma-Aldrich ACS
grade or equivalent).
7.1.4 10 mM AMMONIUM ACETATE/METHANOL - To prepare 1 L, add
0.7708 g ammonium acetate to 1L of methanol. During method
development, this solution was shown to be stable for at least 18 days.
7.1.5 5 mM AMMONIUM ACETATE/REAGENT WATER - To prepare 1 L,
add 0.3854 g ammonium acetate to 1 L of reagent water (pH~6.5). This
solution is prone to volatility losses and should be replaced at least every
48 hours.
7.1.6 AMMONIUM CHLORIDE (NH4C1, CAS#: 12125-02-9) - Acts as a
sample dechlorinating agent (Sect. 8.1.1).
535-10
-------
7.1.7 NITROGEN - Used for the following purposes.
7.1.7.1 Nitrogen aids in aerosol generation of the ESI liquid spray and
used as collision gas in some MS/MS instruments. The nitrogen
used should meet or exceed instrument manufacturer's
specifications.
7.1.7.2 Nitrogen is used to concentrate sample extracts, Ultra High Purity
or equivalent.
7.1.8 ARGON (OPTIONAL) - Can be used as collision gas in some MS/MS
instruments. Argon should meet or exceed instrument manufacturer's
specifications.
7.2 STANDARD SOLUTIONS - Solution concentrations listed in this Section were
used to develop this method and are included as an example. If compounds used
to prepare solutions are 96% pure or greater, the weight may be used without
correction for purity to calculate the concentration of the stock standard.
Standards for sample fortification generally should be prepared in the smallest
volume that can be accurately measured to minimize the addition of organic
solvent to aqueous samples. Even though stability times for standard
solutions are suggested in the following sections, laboratories should use
standard QC practices to determine when Standard Solutions described in
this section need to be replaced.
7.2.1 INTERNAL STANDARD ANALYTE (IS) STANDARD SOLUTION -
BUTACHLOR ESA - This IS was not commercially available when the
method was developed. Thus, the IS was synthesized by the procedure
listed in Appendix A of this method. Commercially available standards
may be used, if available. Alternate internal standards may be used
provided they meet the definition of an IS (Sect. 3.8) and they meet the QC
requirements in Section 9.6.
7.2.1.1 IS STOCK SOLUTION - If preparing from neat material,
accurately weigh approximately 5 mg of the neat IS to the nearest
0.1 mg into a tared, 1-mL volumetric flask. Dilute to the mark
with methanol. Stock solutions have been shown to be stable for
6 months when stored at 4 °C or less.
7.2.1.2 IS PRIMARY DILUTION STANDARD (IS PDS) - Prepare the
IS PDS by adding enough of the IS stock standard to a volumetric
flask partially filled with methanol to make a final concentration
near 10 ug/mL when filled to the mark with methanol. The IS
535-11
-------
PDS has been shown to be stable for 6 months when stored at 4 °C
or less.
7.2.2 SURROGATE ANALYTE (SUR) STANDARD SOLUTION,
DIMETHACHLOR ESA - This SUR was not commercially available
when the method was developed. Thus, the SUR was synthesized by the
procedure listed in Appendix B of this method. Commercially available
standards may be used, if available. Alternate surrogates may be used
provided they meet the definition of a surrogate (Sect. 3.21) and they meet
the QC requirements in Section 9.7.
7.2.2.1 SUR STOCK SOLUTION - If preparing from neat material,
accurately weigh approximately 5 mg of the neat SUR to the
nearest 0.1 mg into a tared, 1-mL volumetric flask. Dilute to the
mark with methanol. Stock solutions have been shown to be stable
for 6 months when stored at 4 °C or less.
7.2.2.2 SUR PRIMARY DILUTION STANDARD (SUR PDS) - Prepare
the SUR PDS by adding enough of the SUR stock standard to a
volumetric flask partially filled with methanol to make a final
concentration near 24 ug/mL when filled to the mark with
methanol. The SUR PDS has been shown to be stable for
12 months when stored at 4 °C or less.
7.2.3 ANALYTE STANDARD SOLUTIONS - Obtain the analytes listed in the
table in Section 1.1 as neat standards. Prepare the Analyte Stock and
Primary Dilutions Standards as described below.
7.2.3.1 ANALYTE STOCK STANDARD SOLUTION - If preparing
from neat material, accurately weigh approximately 5 mg of pure
material to the nearest 0.1 mg into a tared, 5-mL volumetric flask.
Dilute to the mark with methanol. Repeat for each target analyte.
7.2.3.2 ANALYTE PRIMARY DILUTION STANDARD (PDS)
SOLUTION (10-40 ug/mL) - The analyte PDS contains all the
target analytes of interest in methanol at various concentrations.
The ESI and MS/MS response varies by compound; therefore, a
mix of concentrations may be needed in the analyte PDS. See
Tables in Section 17 for suggested concentrations for each analyte.
During method development, the analyte PDS was prepared such
that approximately the same instrument response was obtained for
all the analytes. The analyte PDS is prepared by dilution of the
Analyte Stock Standard solution and is used to prepare the
535-12
-------
calibration standards, and fortify the LFBs, the LFSMs, the
LFSMDs and FDs with the target analytes. The analyte PDS has
been shown to be stable for 6 months when stored at 4 °C or less.
7.2.4 CALIBRATION STANDARDS (CAL) - At least five calibration
concentrations are required to prepare the initial calibration curve spanning
a 20-fold concentration range (Sect. 10.2). Larger concentration ranges
will require more calibration points. Prepare the calibration standards over
the concentration range of interest from dilutions of the analyte PDS in
5mM ammonium acetate/reagent water (Sect. 7.1.5). The target analyte
concentrations found in Tables 5-9 can be used as a starting point for
determining the calibration range. The IS and SUR are added to the
calibration standards at a constant concentration. During method
development, the concentration of the SUR was 120 ug/L in the standard
(0.48 ug/L in the sample) and the IS was 80 ug/L. The lowest
concentration calibration standard must be at or below the MRL, which
may depend on system sensitivity. The CAL standards may be also be
used as CCCs. If stored, the aqueous standards must be stored refrigerated
in the same manner as the samples. During method development, the
calibration standards were shown to be stable for at least two months.
Longer storage times are acceptable provided appropriate QC measures are
documented demonstrating the calibration standard stability.
8. SAMPLE COLLECTION, PRESERVATION, AND STORAGE
8.1 SAMPLE BOTTLE PREPARATION
8.1.1 Prior to shipment to the field, ammonium chloride (Sect. 7.1.6) must be
added as a dry solid to each amber bottle fitted with a PTFE lined screw
cap. A 250-mL sample bottle or larger is recommended. Add ammonium
chloride to yield a sample concentration of 100 mg/L. During method
development, 25 to 30 mg of ammonium chloride was added to each
250-mL sample bottle.
8.1.2 Sample bottles must not be prerinsed with sample before collection.
Doing so will wash out the preservative added to the bottles prior to
shipment.
535-13
-------
8.2 SAMPLE COLLECTION
8.2.1 Open the tap, and allow the system to flush until the water temperature has
stabilized (usually about 2 min). Collect samples from the flowing
system.
8.2.2 When sampling from an open body of water, fill a wide-mouth bottle or
beaker with sample from a representative area, and carefully fill sample
bottles from the container. Sampling equipment, including automatic
samplers, must be free of plastic tubing, gaskets, and other parts that may
leach interfering analytes into the water sample.
8.2.3 Fill sample bottles, taking care not to flush out the sample preservation
reagents. Samples do not need to be collected headspace free.
8.2.4 After collecting the sample, cap carefully to avoid spillage, and agitate by
hand for 1 minute. Keep samples sealed from collection time until
analysis.
8.3 SAMPLE SHIPMENT AND STORAGE - All samples should be cooled (ice or
chemical freeze packs) during shipment and must not exceed 10 °C during the first
48 hours after collection. Samples must be confirmed to be at or below 10 °C
when they are received at the laboratory. Samples stored in the lab must be held
at or below 6 °C and protected from light until analysis. Samples should not be
frozen.
NOTE: Samples that are significantly above 10 °C at the time of collection may
need to be iced or refrigerated for a period of time, in order to chill them prior to
shipping. This will allow them to be shipped with sufficient ice (or chemical
freeze packs) to meet the above requirements.
8.4 SAMPLE AND EXTRACT HOLDING TIMES - Results of the sample storage
stability study of all target analytes indicated that all compounds are stable for
14 days in water samples that are collected, dechlorinated, shipped and stored as
described in Sections 8.1-8.3. Therefore, aqueous samples must be extracted
within 14 days. Sample extracts maybe stored at 4 °C or less for up to 28 days
after sample extraction. Data from holding time studies are shown in Tables 10
and 11.
9. QUALITY CONTROL
9.1 QC requirements include the Initial Demonstration of Capability and ongoing QC
requirements that must be met when preparing and analyzing field samples. This
535-14
-------
section describes each QC parameter, their required frequency, and the
performance criteria that must be met in order to meet EPA quality objectives.
The QC criteria discussed in the following sections are summarized in Section 17,
Tables 12 & 13. These QC requirements are considered the minimum acceptable
QC criteria. Laboratories are encouraged to institute additional QC practices to
meet their specific needs.
9.1.1 METHOD MODIFICATIONS - The analyst is permitted to modify LC
columns and conditions provided the QC in Section 9 is still met. The
analyst is also allowed to modify the internal and surrogate standards.
Each time such method modifications are made, the analyst must repeat
the procedures of the IDC (Sect. 9.2). The analyst may not modify the LC
mobile phase components or LC modifiers (Sect. 13.4.1)
Caution: Matrix enhancement is a significant problem when
analyzing SPE extracts by LC/MS/MS. Thus, if the analyst chooses to
modify the LC conditions (e.g., flow rate, temperature, gradient), care
must be taken ensure that the target analytes do not elute too closely
to the major portion of the TOC elution. An LC/MS analysis of a
spiked matrix extract will be necessary to evaluate this.
9.2 INITIAL DEMONSTRATION OF CAPABILITY (IDC) - The IDC must be
successfully performed prior to analyzing any field samples. Prior to conducting
the IDC, the analyst must first generate an acceptable Initial Calibration following
the procedure outlined in Section 10.2.
9.2.1 INITIAL DEMONSTRATION OF LOW SYSTEM BACKGROUND -
Before any field samples are analyzed, and any time a new set of reagents
or SPE cartridges is used, it must be demonstrated that a laboratory reagent
blank is reasonably free of contamination and that the criteria in
Section 9.3 are met.
9.2.2 INITIAL DEMONSTRATION OF PRECISION - Prepare and analyze
4-7 replicate LFBs fortified at or near the mid-range of the initial
calibration curve, according to the procedure described in Section 11.
Ammonium chloride, as described in Section 8.1.1, must also be added to
these samples. The relative standard deviation (RSD) of the results of the
replicate analyses must be <20% for all target analytes and the surrogate.
9.2.3 INITIAL DEMONSTRATION OF ACCURACY - Using the same set of
replicate LFB data generated for Section 9.2.2, calculate the average
recovery. The average recovery of the replicate values must be within
±30% of the true value.
535-15
-------
9.2.4 MINIMUM REPORTING LEVEL (MRL) CONFIRMATION - Establish
a target concentration for the MRL based on the intended use of the
method. Establish an Initial Calibration following the procedure outlined
in Section 10.2. The lowest calibration standard used to establish the
Initial Calibration (as well as the low-level Continuing Calibration Check
standard) must be at or below the concentration of the MRL. Establishing
the MRL concentration too low may cause repeated failure of ongoing QC
requirements. Confirm or validate the MRL following the procedure
outlined below.1
9.2A.I Fortify, extract, and analyze seven replicate Laboratory Fortified
Blanks at the proposed MRL concentration. These LFBs must
contain ammonium chloride as described in Section 8.1.1.
Calculate the mean (Mean) and standard deviation for these
replicates. Determine the Half Range for the prediction interval
of results (HRPIR) using the equation below
HRPSL = 3.963S
where S is the standard deviation, and 3.963 is a constant value
for seven replicates.
9.2.4.2 Confirm that the upper and lower limits for the Prediction Interval
of Result (PIR = Mean ± HRPIR) meet the upper and lower
recovery limits as shown below.
The Upper PIR Limit must be < 150% recovery.
Mean + HRpm
*100 < 150%
For&jied Concentration
The Lower PIR Limit must be > 50% recovery.
Mean - HRprs
Fortified Concentration
xl 00 > 50%
9.2.4.3 The MRL is validated if both the Upper and Lower PIR Limits
meet the criteria described above (Sect. 9.2.4.2). If these criteria
are not met, the MRL has been set too low and must be
determined again at a higher concentration.
535-16
-------
9.2.5 DL DETERMINATION (optional) - While DL determination is not a
specific requirement of this method, it may be required by various
regulatory bodies associated with compliance monitoring. It is the
responsibility of the laboratory to determine ifDL determination is
required based upon the intended use of the data.
Replicate analyses for this procedure should be done over at least 3 days
(both the sample extraction and the LC/MS/MS analyses should be done
over at least 3 days). Prepare at least 7 replicate LFBs using solutions at a
concentration estimated to be near the DL. This concentration may be
estimated by selecting a concentration at 2-5 times the noise level. The
fortification amount used to obtain the DLs in Table 5 can be used as a
guide, however the appropriate concentration will depend on the
sensitivity of the LC/MS/MS system used. Ammonium chloride must be
added to these samples as described in Section 8.1.1. Analyze the seven
replicates through all steps of Section 11. (NOTE: If an MRL verification
data set meets these requirements, a DL may be calculated from the MRL
verification data, and no additional analyses are necessary). Calculate the
DL using the following equation
Detection Limit = St(n. l^ _ alpha = 099)
where
t(n-u-aipha = o.99) = Student's t value for the 99% confidence level
with n-1 degrees of freedom
n = number of replicates, and
S = standard deviation of replicate analyses.
NOTE: Do not subtract blank values when performing DL calculations.
The DL is a statistical determination of precision only.2 If the DL
replicates are fortified at a low enough concentration, it is likely that they
will not meet the precision and accuracy criteria for CCCs, and may result
in a calculated DL that is higher than the fortified concentration.
Therefore, no precision and accuracy criteria are specified.
9.2.6 CALIBRATION CONFIRMATION - If a QCS is available, analyze the
QCS as described in Section 9.11 to confirm the accuracy of the
standards/calibration curve.
9.3 LABORATORY REAGENT BLANK (LRB) - An LRB is required with each
extraction batch (Sect. 3.6) of samples to determine any background system
contamination. If within the retention time window of any analyte, the LRB
produces a peak that would prevent the determination of that analyte, determine
535-17
-------
the source of contamination and eliminate the interference before processing
samples. Background contamination must be reduced to an acceptable level
before proceeding. Background from target analytes or contaminants that
interfere with the measurement of target analytes must be < 1/3 the MRL. If the
target analytes are detected in the LRB at concentrations equal to or greater than
this level, then all data for the problem analyte(s) must be considered invalid for
all samples in the extraction batch. Any time a new batch of SPE materials is
received, or new supplies of other reagents are used, repeat the demonstration of
low system background described in Section 9.2.1.
NOTE: Although quantitative data below the MRL may not be reliably accurate
for data reporting, such data is useful in determining an MRL cut off for analytes
that are typically detected in LRBs. Therefore, blank contaminantion levels may
be estimated by extrapolation, when the concentration is below the lowest
calibration standard.
9.4 CONTINUING CALIBRATION CHECK (CCC) - CCC Standards are analyzed
at the beginning of each analysis batch, after every ten field samples, and at the
end of the analysis batch. See Section 10.3 for concentration requirements,
frequency requirements, and acceptance criteria.
9.5 LABORATORY FORTIFIED BLANKS (LFB) - With each extraction batch,
extract and analyze an LFB containing each analyte of concern. If more than 20
field samples are included in a batch, analyze an LFB for every 20 samples. The
fortified concentration of the LFB must be rotated between low, medium, and
high concentrations from batch to batch. The low concentration LFB must be as
near as practical to the MRL. Similarly, the high concentration LFB should be
near the high end of the calibration range established during the initial calibration
(Sect. 10.2). Results of LFB analyses corresponding to the low fortification
concentration for an analyte must be within 50-150% of the true value for all
analytes. Results of LFB analyses from medium and high level concentrations
must be 70-130% of the true value for all analytes. If the LFB results do not meet
these criteria for target analytes, then all data for the problem analyte(s) must be
considered invalid for all samples in the extraction batch.
9.6 INTERNAL STANDARDS (IS) - The analyst must monitor the peak area of the
IS in all injections during each analysis batch. The IS response (as indicated by
peak area) in each chromatographic run must not deviate by more than ±50% from
the average area measured during the initial calibration for the IS. A poor
injection, as well as matrix enhancement or suppression, could cause the IS area
to exceed these criteria. Inject a second aliquot of the suspect extract to determine
whether the failure is due to poor injection.
535-18
-------
9.6.1 If the reinjected aliquot produces an acceptable internal standard response,
report results for that injection.
9.6.2 If the IS area for the reinjected extract deviates greater than 50% from the
initial calibration average, the analyst should check the continuing
calibration check standards that ran before and after the sample. If the
continuing calibration check fails the criteria of Section 10.3, recalibration
is in order per Section 10.2, followed by sample reanalysis. If the
calibration standard is acceptable, extraction of the sample should be
repeated provided the sample is still within holding time. If reextraction is
not possible, sample recollection should be ordered if data is supporting a
regulatory monitoring requirement. Otherwise, report results obtained
from the reinjected extract, but annotate as suspect.
9.7 SURROGATE (SUR) RECOVERY - The SUR PDS is fortified into all
calibration standards, samples, LFBs, LFSMs, LFSMDs, FDs, and LRBs. The
SUR is also added to the calibration curve and calibration check standards. The
SUR is a means of assessing method performance from extraction to final
chromatographic measurement.
9.7.1 Surrogate recovery criteria are 70-130% of the fortified amount for the
method surrogate. When surrogate recovery from a sample, blank, or
CCC does not meet these criteria, check : (1) calculations to locate
possible errors, (2) standard solutions for degradation, (3) contamination,
and (4) instrument performance. Correct any problems that are identified.
If these steps do not reveal the cause of the problem, reanalyze the extract.
9.7.2 If the reanalysis meets the surrogate recovery criterion, report only data for
the reanalyzed extract.
9.7.3 If the extract reanalysis fails the 70-130% recovery criterion, the analyst
should check the calibration by reinjecting the most recently acceptable
calibration standard. If the calibration standard fails the criteria of
Section 10.3, recalibration is in order (Sect. 10.2), followed by sample
reanalysis. If the calibration standard is acceptable and a duplicate sample
is available, extraction and analysis of the duplicate should be performed
provided the sample is still within the holding time. If a duplicate sample
is not available, sample recollection should be ordered if the data is
supporting a regulatory monitoring requirement. If this sample reanalysis
also fails the recovery criterion, report all data for that sample as suspect
due to surrogate recovery failure or potential sample matrix effect.
535-19
-------
9.8 LABORATORY FORTIFIED SAMPLE MATRIX (LFSM) - Analysis of an
LFSM is required in each extraction batch and is used to determine that the
sample matrix does not adversely affect method accuracy. Assessment of method
precision is accomplished by analysis of a Field Duplicate (Sect. 9.9), however,
infrequent occurrence of target analytes would hinder this assessment. If the
occurrence of target analytes in the samples is infrequent, or if historical trends are
unavailable, a second LFSM, or LFSMD, must be prepared, extracted, and
analyzed from a duplicate of the field sample. Extraction batches that contain
LFSMDs will not require the extraction of a Field Duplicate. If a variety of
different sample matrices are analyzed regularly, for example, drinking water
from groundwater and surface water sources, method performance should be
established for each. Over time, LFSM data should be documented for all routine
sample sources for the laboratory.
9.8.1 Within each extraction batch, a minimum of one field sample is fortified
as an LFSM for every 20 samples extracted. The LFSM is prepared by
spiking a sample with an appropriate amount of the analyte PDS
(Sect. 7.2.3.2). Select a spiking concentration that is greater than or equal
to the matrix background concentration, if known. Use historical data and
rotate through the designated concentrations when selecting a fortifying
concentration, such that fortified concentrations range from near the MRL
to the high level standard. LFSM recoveries may fall outside the
acceptance limits (Sect. 9.8.3) if an analyte is present in the sample at a
concentration that greatly exceeds the spiking concentration.
9.8.2 Calculate the percent recovery (R) for each analyte using the equation
c
where
A = measured concentration in the fortified sample
B = measured concentration in the unfortified sample, and
C = fortification concentration.
9.8.3 Analyte recoveries may exhibit a matrix bias. For samples fortified at or
above their native concentration, recoveries should be between 60-140%,
except for low-level fortification near or at the MRL (within a factor of
two times the MRL concentration), where 50-150% recoveries are
acceptable. If the accuracy of any analyte falls outside the designated
range, and the laboratory performance for that analyte is shown to be in
control in the CCCs, the recovery is judged to be matrix biased. The result
535-20
-------
for that analyte in the unfortified sample is labeled suspect/matrix to
inform the data user that the results are suspect due to matrix effects.
9.9 FIELD DUPLICATE OR LABORATORY FORTIFIED SAMPLE MATRIX
DUPLICATE (FD or LFSMD) - Within each extraction batch, a minimum of one
Field Duplicate (FD) or Laboratory Fortified Sample Matrix Duplicate (LFSMD)
must be analyzed. Duplicates check the precision associated with sample
collection, preservation, storage, and laboratory procedures. If target analytes are
not routinely observed in field samples, an LFSMD must be analyzed rather than a
FD. Refer to Section 9.8.1 for guidance on spiking concentrations.
9.9.1 Calculate the relative percent difference (RPD) for duplicate
measurements (FD1 and FD2) using the equation
FD1-FD2
RPD = *100
(FDl + FD2)/2
9.9.2 If an LFSMD is analyzed instead of a Field Duplicate, calculate the
relative percent difference (RPD) for duplicate LFSMs (LFSM and
LFSMD) using the equation
ILFSM - LFSMD
RPD = -! *1QO
(LFSM +LFSMD)/2
9.9.3 RPDs for FDs, or duplicate LFSMs, should fall in the range of 0-30% for
samples fortified at or above their native concentration. Greater variability
may be observed when LFSMs are spiked near the MRL. At the MRL,
RPDs should fall in the range of 0-50% for samples fortified at or above
their native concentration. If the RPD of any analyte falls outside the
designated range, and the laboratory performance for that analyte is shown
to be in control in the LFB, the recovery is judged to be matrix biased.
The result for that analyte in the unfortified sample is labeled
suspect/matrix to inform the data user that the results are suspect due to
matrix effects.
9.10 RESOLUTION CHECK - The resolution of alachlor ESA and acetochlor ESA, in
a calibration standard or CCC near or above mid level calibration, must be
monitored in each analysis batch. These closely eluting peaks, which are not
baseline resolved, must have a resolution (Rs) of 1.0 or greater using the equation
3 w + w
"0.5,1 "0.5,2
535-21
-------
where
tj and t2 = retention times of the first and second adjacent peaks in minutes
W0 5 j and W0 5 2 = widths of the adjacent peaks at half height in minutes.
At a minimum, resolution must be monitored once for every 24-hour analysis
batch and may be monitored at any time during the 24-hour period. It is
recommended that resolution be checked prior to sample analysis, especially if the
system in use has a history of resolution problems. If a resolution check fails, the
problem must be corrected and all samples analyzed since the most recent
successful calculation of the resolution check, including the QC samples, must be
reanalyzed.
Note: Alachlor ESA and acetochlor ESA are structural isomers and have nearly
identical product ions in MS/MS. There are dissimilar products ions at m/z 176
(alachlor ESA) and m/z 162 (acetochlor ESA); however, their relative intensity is
typically less than 20%. If sufficient sensitivity for these dissimilar ions can be
achieved, these ions may be used for quantitation and the resolution requirement
is not necessary.
9.11 QUALITY CONTROL SAMPLE (QCS) - The QCS is required only if an
alternate source is available for these target analytes. Each time that new PDSs
are prepared, analyze a QCS from an external source. If standards are prepared
infrequently, analyze a QCS at least quarterly. The QCS may be injected as a
calibration standard, or fortified into reagent water and analyzed as an LFB. If the
QCS is analyzed as a calibration check standard, then the acceptance criteria are
the same as for the CCC (Sect. 10.3.3). If the QCS is analyzed as an LFB, then
the acceptance criteria are the same as for an LFB (Sect. 9.5). If measured analyte
concentrations are not of acceptable accuracy, check the entire analytical
procedure to locate and correct the problem.
10. CALIBRATION AND STANDARDIZATION
10.1 After initial calibration is successful, a Continuing Calibration Check (CCC) is
required at the beginning and end of each analysis batch, and after every tenth
sample (Sect. 10.3). Initial calibration should be repeated each time a major
instrument modification or maintenance is performed.
10.2 INITIAL CALIBRATION
10.2.1 ESI-MS/MS TUNE
10.2.1.1 Calibrate the mass scale of the MS with the calibration
compounds and procedures prescribed by the manufacturer.
535-22
-------
10.2.1.2 Optimize the [M-H]~ for each target analyte by infusing
approximately 0.5-1.0 ug/mL of each analyte (prepared in the
initial mobile phase conditions) directly into the mass
spectrometer at the LC mobile phase flow rate (approximately
0.4 mL/min). This tune can be done on a mix of the target
analytes. The MS parameters (capillary voltage, temperatures,
gas flows, etc.) are varied until optimal analyte responses are
determined. The ESAs and OAs may have different optima
requiring some compromise between the optima. See Table 2 for
ESI-MS conditions used in method development.
10.2.1.3 Optimize the product ion (Sect. 3.18) for each target by infusing
approximately 0.5-1.0 ug/mL of each analyte (prepared in the
initial mobile phase conditions) directly into the mass
spectrometer at the LC mobile phase flow rate (approximately
0.4 mL/min). This tune can be done on a mix of the target
analytes. The MS/MS parameters (collision gas pressure,
collision energy, etc.) are varied until optimal analytes responses
are determined. Typically, all the ESAs have very similar
MS/MS conditions and all the OAs have similar MS/MS
conditions. See Tables 3 and 4 for MS/MS conditions used in
method development.
10.2.2 Establish LC operating parameters equivalent to the suggested conditions
in Section 17, Table 1.
10.2.3 Inject a mid-level CAL standard under LC/MS conditions to obtain the
retention times of each target analyte. Ensure that the LC conditions are
adequate to meet the resolution check in Section 9.10 for alachlor ESA
and acetochlor ESA. Divide the chromatogram into retention time
windows each of which contains one or more chromatographic peaks.
During MS/MS analysis, fragment a small number of selected precursor
ions ([M-H]~; Sect. 3.16) for the analytes in that window and choose the
most abundant product ion. The product ions (also the quantitation ion)
chosen during method development are in Tables 3 and 4, although these
will be instrument dependent. For maximum sensitivity, small mass
windows of ±2 daltons (depending on the instrument) around the product
ion mass were used. If sufficient sensitivity exists to meet the MRL, wider
mass ranges may be used to obtain more confirmation ions.
10.2.4 Inject a mid-level CAL standard under LC/MS/MS conditions to ensure
that each target analyte is observed in its MS/MS window and that there is
at least 20 scans across the peak for optimum precision. Ensure that there
535-23
-------
are enough scans on either side of the chromatographic peak to account for
shifts in retention times due to injection imprecision.
10.2.5 Prepare a set of at least 5 CAL standards as described in Section 7.2.4.
The lowest concentration CAL standard must be at or below the MRL,
which may depend on system sensitivity. It is recommended that at least
four of the CAL standards are at a concentration greater than or equal to
the MRL.
10.2.6 The LC/MS/MS system is calibrated using the internal standard technique.
Concentrations may be calculated through the use of average relative
response factor (RRF) or through the use of a calibration curve. Calculate
the RRFs using the equation
where
Ax = integrated abundance (peak area) of the quantitation ion
of the analyte.
Ais = integrated abundance (peak area) of the IS quantitation
ion.
Qx = quantity of analyte injected in ng or concentration units.
Qis = quantity of internal standard injected in ng or
concentration units.
RRF = relative response factor
Average RRF calibrations may only be used if the RRF values over the
calibration range are relatively constant. Average RRF is determined by
calculating the mean RRF of a minimum of five calibration concentrations.
Average RRF calibrations may only be used if the criteria in Section 10.2.8
are met.
10.2.7 As an alternative to calculating average RRFs, use the LC/MS/MS data
system software to generate a linear regression or quadratic calibration
curve. Forcing the calibration curve through the origin is not
recommended. The triple quadrupole instrument used during method
development yielded linear curves for the target analytes over the
concentration range of interest. However, the ion trap instrument yielded
weighted (1/X) quadratic curves. Data may be fit with either a linear
regression (response vs. concentration) or quadratic fit (response vs.
concentration) and weighting may be used, if necessary.
535-24
-------
10.2.8 When quantitated using the initial calibration curve, each calibration point,
except the lowest point, for each analyte should calculate to be within
70-130% of its true value. The lowest calibration point should calculate to
be within 50-150% of its true value. If these criteria cannot be met, the
analyst will have difficulty meeting ongoing QC criteria. It is
recommended that corrective action is taken to reanalyze the calibration
standards, restrict the range of calibration, or select an alternate method of
calibration.
CAUTION: When acquiring MS/MS data, LC operating conditions must be
carefully reproduced for each analysis to provide reproducible retention
times. If this is not done, the correct ions will not be monitored at the
appropriate times. As a precautionary measure, the chromatographic peaks
in each window must not elute too close to the edge of the time window.
10.3 CONTINUING CALIBRATION CHECK (CCC) - Minimum daily calibration
verification is as follows. Verify the initial calibration at the beginning and end of
each group of analyses, and after every tenth sample during analyses. In this context,
a "sample" is considered to be a field sample. LRBs, CCCs, LFBs, LFSMs, FDs and
LFSMDs are not counted as samples. The beginning CCC each day must be at or
below the MRL in order to verify instrument sensitivity prior to any analyses. If
standards have been prepared such that all low CAL points are not in the same CAL
solution, it may be necessary to analyze two CAL standards to meet this
requirement. Alternatively, the analyte concentrations in the analyte PDS may be
customized to meet this criteria. Subsequent CCCs should alternate between a
medium and high concentration CAL standard.
10.3.1 Inject an aliquot of the appropriate concentration CAL standard and analyze
with the same conditions used during the initial calibration.
10.3.2 Determine that the absolute area of the quantitation ion of the internal
standard has not changed by more than ± 50% from the average area
measured during initial calibration. If the IS area has changed by more than
±50%, remedial action maybe necessary (Sect. 10.3.4). If the loss in area
cannot be recovered, recalibrate according to Section 10.2 and verify
sensitivity by analyzing a CCC at or below the MRL (Sect 10.3.3). Control
charts are useful aids in documenting system sensitivity changes.
10.3.3 Calculate the concentration of each analyte and surrogate in the CCC. The
calculated amount for each analyte for medium and high level CCCs must
be ± 30% of the true value. The calculated amount for the lowest
calibration point for each analyte must be within ± 50% of the true value. If
these conditions do not exist, then all data for the problem analyte must be
535-25
-------
considered invalid, and remedial action should be taken (Sect. 10.3.4)
which may require recalibration. Any field or QC samples that have been
analyzed since the last acceptable calibration verification should be
reanalyzed after adequate calibration has been restored, with the following
exception. If the CCC fails because the calculated concentration is
greater than 130% (150% for the low-level CCC) for a particular
target analyte, and field sample extracts show no detection for that
target analyte, non-detects may be reported without reanalysis.
10.3.4 REMEDIAL ACTION - Failure to meet CCC QC performance criteria may
require remedial action. Major maintenance such a cleaning the
atmospheric pressure ionization source, cleaning the mass analyzer,
replacing the LC column, etc., require returning to the initial calibration
step (Sect. 10.2).
11. PROCEDURE
11.1 This procedure may be performed manually (Sect. 11.4) or in an automated mode
(Sect. 11.3) using a robotic or automatic sample preparation device. The data
presented in Tables 5-11 demonstrate data collected by both manual and automated
extraction. Extraction and/or elution steps may not be changed or omitted in the
manual or automated mode.
11.2 SAMPLE PREPARATION
11.2.1 Samples are dechlorinated, collected and stored as presented in Section 8.
All field and QC samples must contain the dechlorinating agent listed in
Section 8.1.1, including the LRB and LFB. Determine sample volume. The
sample volume may be measured directly in a graduated cylinder to the
nearest 10 mL. To minimize the need to use a different graduated cylinder
for each sample, an indirect measurement may be done in one of two ways:
by marking the level of the sample on the bottle or by weighing the sample
and bottle to the nearest 10 g. After extraction, proceed to Section 11.6 for
final volume determination. The LRB and LFB may be prepared by
measuring 250 mL of reagent water with a graduated cylinder or filling a
250-mL sample bottle to near the top.
11.2.2 Add an aliquot of the SUR PDS (Sect. 7.2.2.2) to each sample, cap and
invert to mix. During method development, a 5-uL aliquot of the 24 ug/mL
SUR PDS was added to 250 mL of sample for a final concentration of
0.48 ug/L.
535-26
-------
11.2.3 In addition to the SUR and dechlorination agent, if the sample is an LFB,
FD, LFSM, or LFSMD, add the necessary amount of analyte PDS
(Sect. 7.2.3.2). Cap and invert each sample to mix.
11.2.4 Continue to Section 11.3 if performing automated extractions or 11.4 if
performing manual extractions.
11.3 AUTOMATED CARTRIDGE SPE PROCEDURE
11.3.1 The parameters used during method development are shown in the table
below. Minor modifications to the automated method are allowed
providing the QC criteria in Section 9 are met. Modifications to the
solvents used and the volumes of solvents used is not permitted.
Zvmark AutoTrace Extraction Workstation Procedure
Step 1:
Step 2:
Step 3:
Step 4:
Step 5:
Step 6:
Step 7:
Step 8:
Step 9:
Step 10:
Step 11:
Step 12:
Step 13:
Process 6 samples using the following procedure:
Condition cartridge with 10 mL of 10 mM ammonium
Condition cartridge with 10 mL of 10 mM ammonium
Condition cartridge with 10 mL of reagent water
Condition cartridge with 10 mL of reagent water
Condition cartridge with 10 mL of reagent water
Load 275 mL of sample onto cartridge**
Rinse cartridge with 5 mL of reagent water
Dry cartridge with nitrogen gas for 3 minutes
acetate/MeOH
acetate/MeOH
Soak and collect 5-mL fraction using 10 mM ammonium acetate/MeOH
Collect 10-mL fraction using 10 mM ammonium acetate/MeOH
Clean each sample path with 50 mL of reagent water
End
Flow Rates
Condition: 10 mL/min
Load:
Rinse:
10 mL/min
5 mL/min
Elute: 5 mL/min
Cond Air Push: 10 mL/min
Rinse Air Push: 10 mL/min
Elute Air Push: 5 mL/min
SPE Parameters
Push Delay:
Air Factor:
Autowash Vol.:
5 sec
0.0
2.00 mL
*A sampl
e volume larger than the actual sample size is entered to ensure that all of the sample is
535-27
-------
11.3.2 After automated collection of the eluant into the collection tubes, transfer
the collection tubes to the nitrogen evaporator and proceed to Section 11.5.
11.4 MANUAL CARTRIDGE SPE PROCEDURE
11.4.1 CARTRIDGE CLEAN-UP AND CONDITIONING - DO NOT allow
cartridge packing material to go dry during any of the conditioning steps.
Rinse each cartridge with 20 mL of 10 mM ammonium acetate/methanol
(Sect. 7.1.4). Next, rinse each cartridge with 30 mL of reagent water,
without allowing the water to drop below the top edge of the packing. If the
cartridge goes dry during the conditioning phase, the conditioning must be
started over. Add approximately 3 mL of reagent water to the cartridge,
attach the transfer tube, turn on the vacuum, and begin adding sample to the
cartridge.
11.4.2 SAMPLE EXTRACTON - Adjust the vacuum so that the approximate flow
rate is 10-15 mL/min. Do not allow the cartridge to go dry before all the
sample has passed through. After all of the sample has passed through the
cartridge, remove the transfer tubing from the top of the cartridge and rinse
the cartridge with 5 mL of reagent water. Draw air or nitrogen through the
cartridge for 3 min at high vacuum (10-15 in. Hg).
11.4.3 CARTRIDGE ELUTION - Lift the extraction manifold top and insert a
rack with collection tubes into the extraction tank to collect the extracts as
they are eluted from the cartridge. Elute the analytes from the cartridge
with 15 mL of 10 mM ammonium acetate/methanol at a low vacuum
(5 mL/min used to collect method data), such that the solvent exits the
cartridge in a dropwise fashion.
11.5 EXTRACT CONCENTRATION - Concentrate the extract to dryness under a gentle
stream of nitrogen in a heated water bath (60-70 °C) to remove all the ammonium
acetate/methanol. Add the appropriate amount of 5 mM ammonium acetate/reagent
water (Sect. 7.1.5) and the IS PDS (Sect. 7.2.1.2) to the collection vial to bring the
volume to 1 mL (10 uL of the 8 ug/mL IS PDS for an extract concentration of
80 ug/L used for method development). Transfer to autosampler vial.
11.6 SAMPLE VOLUME DETERMINATION - If the level of the sample was marked
on the sample bottle, use a graduated cylinder to measure the volume of water
required to fill the original sample bottle to the mark made prior to extraction.
Determine to the nearest 10 mL. If using weight to determine volume, weigh the
empty bottle to the nearest 10 g and determine the sample weight by subtraction of
the empty bottle from the original weight (Sect. 11.2.1). Assume a sample density of
1.0 g/mL. In either case, the sample volume will be used in the final calculations of
the analyte concentration (Sect. 12.2).
535-28
-------
11.7 EXTRACT ANALYSIS
11.7.1 Establish operating conditions equivalent to those summarized in Tables
1-4 of Section 17. Instrument conditions and columns should be optimized
prior to the initiation of the IDC. Confirm that resolution of alachlor ESA
and acetochlor ESA peaks meets the requirements of Section 9.10.
11.7.2 Establish an appropriate retention time window for each analyte. This
should be based on measurements of actual retention time variation for each
compound in standard solutions analyzed on the LC over the course of time.
Plus or minus three times the standard deviation of the retention time
obtained for each compound while establishing the initial calibration and
completing the IDC can be used to calculate a suggested window size;
however, the experience of the analyst should weigh heavily on the
determination of the appropriate retention window size.
11.7.3 Calibrate the system by either the analysis of a calibration curve (Sect. 10.2)
or by confirming the initial calibration is still valid by analyzing a
continuing calibration check as described in Section 10.3. If establishing an
initial calibration for the first time, complete the IDC as described in
Section 9.2. Confirm that the system meets the resolution check criteria as
described in Section 9.10 once for every 24-hour analytical batch.
11.7.4 Begin analyzing field and QC samples at their appropriate frequency by
injecting the same size aliquots (100 uL was used in method development),
under the same conditions used to analyze the initial calibration.
11.7.5 At the conclusion of data acquisition, use the same software that was used
in the calibration procedure to identify peaks of interest in predetermined
retention time windows. Use the data system software to examine the ion
abundances of the peaks in the chromatogram. Identify an analyte by
comparison of its retention time with that of the corresponding analyte peak
in a reference standard. Comparison of the mass spectra is not particularly
useful given the limited ±1-2 dalton mass range around a single product ion
for each target analyte.
CAUTION: Alachlor ESA and acetochlor ESA are not baseline
resolved under the conditions in this method and they have the same
quantitation ion. Each chromatogram must be manually checked by
the analyst to verify that the data system has correctly identified the
peaks in the alachlor ESA/acetochlor ESA retention time window.
11.7.6 The analyst must not extrapolate beyond the established calibration range.
If an analyte peak area exceeds the range of the initial calibration curve, the
535-29
-------
extract may be diluted with 5 mM ammonium acetate/reagent water
(Sect. 7.1.5) with the appropriate amount of internal standard added to
match the original concentration. Re-inject the diluted extract. Incorporate
the dilution factor into the final concentration calculations. Acceptable
surrogate performance (Sect. 9.7) should be determined from the undiluted
sample extract. The resulting data should be documented as a dilution, with
an increased MRL.
12. DATA ANALYSIS AND CALCULATION
12.1 Complete chromatographic resolution is not necessary for accurate and precise
measurements of analyte concentrations using MS/MS with the exception of
alachlor ESA and acetochlor ESA (Sect. 9.10). In validating this method,
concentrations were calculated by measuring the product ions listed in Tables 3 and
4. Other ions may be selected at the discretion of the analyst.
12.2 Calculate analyte and surrogate concentrations, using the multipoint calibration
established in Section 10. Do not use daily calibration verification data to quantitate
analytes in samples. Adjust final analyte concentrations to reflect the actual sample
volume determined in Section 11.6.
12.3 Prior to reporting the data, the chromatogram should be reviewed for any incorrect
peak identification (especially in the case of the closely resolved acetochlor ESA and
alachlor ESA) or poor integration.
12.4 Calculations must utilize all available digits of precision, but final reported
concentrations should be rounded to an appropriate number of significant figures
(one digit of uncertainty), typically two, and not more than three significant figures.
Note: Some data in Section 17 of this method are reported with more than two
significant figures. This is done to better illustrate the method performance.
13. METHOD PERFORMANCE
13.1 PRECISION, ACCURACY, DLs AND LCMRLs - Demonstration data are
presented using two commercially available tandem mass spectrometers in two
separate laboratories. DLs and LCMRLs are presented in Section 17, Table 5.
Precision and accuracy are presented for four water matrices: reagent water (Table 6
and 7); chlorinated (finished) surface water (Table 8); high TOC chlorinated surface
water (Table 9); and day zero of the holding time in chlorinated ground water
(Table 10).
13.2 EVALUATION OF ADDITIONAL ACETANILIDE DEGRADATES - Propachlor
sulfinyl acetic acid (SAA) and alachlor SAA were evaluated for inclusion in this
535-30
-------
method. The two compounds were not included due to low and inconsistent
recoveries on the carbon cartridges.
13.3 ANALYTE STABILITY STUDIES
13.3.1 AQUEOUS SAMPLES - Chlorinated ground water samples, fortified with
target analytes at 0.10-0.80 ug/L, were preserved and stored as required in
Section 8. The average of seven replicate analyses, conducted on days 0, 7,
and 14 are presented in Section 17, Table 10. These data document the
14-day sample holding time.
13.3.2 EXTRACTS - Extracts from the first day of the holding time study
described above were stored at 4 °C, and analyzed in replicate (N=7) on
days 0, 7, 14, 21, and 28. The results of these analyses are presented in
Table 11 and document the 28-day extract holding time.
13.4 PROBLEM COMPOUNDS
13.4.1 MATRIX ENHANCEMENT - Propachlor OA and fiufenacet OA were
prone to ESI matrix enhancement in chlorinated surface waters containing
approximately 2 mg/L or higher TOC. ESI matrix enhancement of
propachlor OA (132%) and fiufenacet OA (158%) was observed in typical
chlorinated surface water using the ion trap instrument (Table 8) due to
co-eluting TOC. This matrix enhancement was not observed using the
triple quadrupole instrument due to the different LC conditions (Table 1)
used. The TOC eluted earlier in the chromatogram when using the triple
quadrupole LC conditions instead of the ion trap LC conditions, thus less
matrix enhancement was observed using the triple quadruple LC conditions.
Because ion trap instruments have much longer MS/MS scan cycles than
triple quadrupole instruments, different LC conditions were necessary on
the ion trap instrument in order to broaden the chromatographic peaks to
obtain a minimum of 20 scans across the peak. Additional information on
LC/MS matrix enhancement can be found in the literature.6'7
This matrix enhancement is the primary reason for not allowing
modifications to the LC mobile phase constituents. Where the TOC elutes
in the chromatogram versus the target analytes will determine the amount of
matrix enhancement as well as which analytes are affected. Matrix
enhancement was well characterized during method development, using the
LC conditions listed in Table 1, to ensure minimal inferences due to TOC.
13.4.2 SPE BREAKTHROUGH - Without the presence of matrix enhancement to
obscure SPE recovery losses, the data using a triple quadrupole instrument
in Table 9 illustrates the loss in recovery for propachlor OA (33%) and
535-31
-------
flufenacet OA (42%) due to excessive TOC (8.6 mg/L) affecting retention
on the graphitized carbon solid phase sorbent. The recoveries of
propachlor OA (75%) and flufenacet OA (96%) on the ion trap instrument
do not appear to be low, but similar to the values in Table 8, the
propachlor OA and flufenacet OA recoveries in Table 9 are really matrix
enhanced. Thus, the actual SPE sorbent recoveries for propachlor OA and
flufenacet OA are probably more similar to those observed for the triple
quadrupole data in Table 9.
13.5 SECOND LABORATORY DEMONSTRATION - The performance of this method
was demonstrated on the triple quadrupole instrument by a second laboratory and
included in Section 17, Tables 5-9. The detection limits and LCMRLs observed on
the triple quadrupole instrument are higher than the ion trap instrument. Different
LC/MS/MS systems and ESI interfaces respond very differently to the various
method parameters (e.g., LC mobile phase and modifiers) and the target analytes.
For example, a second triple quadrupole LC/MS/MS system investigated during the
method development was more similar in sensitivity to the ion trap instrument. The
authors wish to acknowledge the work of Dr. Glynda Smith of Shaw Environmental
Incorporated for her participation in the second laboratory demonstration.
14. POLLUTION PREVENTION
14.1 This method utilizes SPE technology to remove the analytes from water. It requires
the use of small volumes of solvent and very small quantities of pure analytes,
thereby minimizing the potential hazards to both the analyst and the environment
when compared with the use of large volumes of organic solvents in conventional
liquid-liquid extractions.
14.2 For information about pollution prevention that may be applicable to laboratory
operations, consult "Less is Better: Laboratory Chemical Management for Waste
Reduction" available from the American Chemical Society, on-line at
http://membership.acs.org/c/ccs/pub_9.htm.
15. WASTE MANAGEMENT
15.1 The analytical procedures described in this method generate relatively small amounts
of waste since only small amounts of reagents and solvents are used. The matrices
of concern are finished drinking water. However, the Agency requires that
laboratory waste management practices be conducted consistent with all applicable
rules and regulations, and that laboratories protect the air, water, and land by
minimizing and controlling all releases from fume hoods and bench operations.
Also, compliance is required with any sewage discharge permits and regulations,
particularly the hazardous waste identification rules and land disposal restrictions.
535-32
-------
16. REFERENCES
1. "Statistical Protocol for the Determination of the Single-Laboratory Lowest Concentration
Minimum Reporting Level (LCMRL) and Validation of the Minimum Reporting Level
(MRL)," available at www.epa.gov/OGWDW/methods/sourcalt.html.
2. Glaser, J.A., D.L. Foerst, G.D. McKee, S.A. Quave, and W.L. Budde, "Trace Analyses for
Wastewaters," Environ. Sci. Technol. 1981, 15, 1426-1435.
3. "OSHA Safety and Health Standards, General Industry," (29CRF1910). Occupational
Safety and Health Administration, OSHA 2206, (Revised, July 1, 2001).
4. "Carcinogens-Working with Carcinogens," Publication No. 77-206, Department of Health,
Education, and Welfare, Public Health Service, Center for Disease Control, National
Institute of Occupational Safety and Health, Atlanta, Georgia, August 1977.
5. "Safety in Academic Chemistry Laboratories," American Chemical Society Publication,
Committee on Chemical Safety, 6th Edition, available from the ACS Office of Society
Services by e-mail at OSS@acs.org.
6. Leenheer, J.A., C.E. Rostad, P.M. Gates, E.T. Furlong, and I. Ferrer, "Molecular
Resolution and Fragmentation of Fulvic Acid by Electrospray lonization/Multistage
Tandem Mass Spectrometry." Anal. Chem. 2001, 73, 1461-1471.
7. Cahill, J.D., E.T. Furlong, M.R. Burkhardt, D. Kolpin, and L.G. Anderson, "Determination
of Pharmaceutical Compounds in Surface- and Ground-Water Samples by Solid-Phase
Extraction and High-Performance Liquid Chromatography Electrospray lonization Mass
Spectrometry," J. Chromatogr. A 2004. 1041, 171-180.
535-33
-------
17. TABLES. DIAGRAMS. FLOWCHARTS. AND DEMONSTRATION DATA*
TABLE 1. LC METHOD CONDITIONS
Triple Quadrupole Conditions
Time
(min)
initial
7.0
10.0
18.0
20.0
25.0
25.1
40.0
% 5mM
ammonium
acetate
90.0
80.0
75.0
75.0
20.0
20.0
90.0
90.0
% Methanol
10.0
20.0
25.0
25.0
80.0
80.0
10.0
10.0
Agilent Hypersil 2.1 x 100 mm packed
with 5.0 um Clg stationary phase
Flow rate of 0.25 mL/min
Column Temperature of 65°C
100 uL injection
Ion Trap Conditions
Time
(min)
initial
5.0
10.0
35.0
35.1
57.0
% 5mM
ammonium
acetate
95.0
72.0
72.0
20.0
95.0
95.0
% Methanol
5.0
28.0
28.0
80.0
5.0
5.0
Agilent Hypersil 2. 1 x 200 mm packed
with 5.0 um Clg stationary phase
Flow rate of 0.4 mL/min
Column Temperature of 65°C
100 uL injection
TABLE 2. ESI-MS METHOD CONDITIONS
Triple Quadrupole ESI Conditions
Polarity
Capillary needle voltage
Cone gas flow
Nitrogen desolvation gas
Desolvation gas temp.
Cone voltage
Negative ion
-3kV
50 L/hr
500 L/hr
210°C
40V
Ion Trap ESI Conditions
Polarity
Capillary needle voltage
Nitrogen sheath gas
Nitrogen auxiliary gas
Heated capillary
Negative ion
-3kV
80 (unitless)
20 (unitless)
275°C
* Instrumentation, when specified, does not constitute endorsement. Brand names are included for illustration only.
535-34
-------
TABLE 3. TRIPLE QUADRUPOLE MS/MS METHOD CONDITIONS
Segment
#b
1
1
2
2
2
3
3
3
4
4
4
4
2
5
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Dimethachlor ESA (SUR)
Butachlor ESA (IS)
Retention Time
(min)
7.33
8.67
10.01
10.81
13.25
14.87 & 15. 11 e
15.86
16.34
18.46
18.60
19.12
20.95
12.18 e
36.95
Precursor
Ion (m/z)
206
224
256
274
270
320
264
264
314
278
314
328
300
356
Product
Ion (m/z)c'd
134
152
80
80
198
80
160f
146f
80
206
80
80
80
80
Collision
Energy
(ev)
8
10
25
25
10
25
10
10
25
8
30
25
25
25
a Argon used as collision gas at 2 mtorr.
b Segments are time durations in which single or multiple scan events occur.
c Ions used for quantitation purposes.
d Scan width was ±0.5 daltons.
Analyte has two partially resolved chromatographic peaks due to stereoisomers. Both peaks
summed for quantitation purposes.
f Scan range was 145-161 daltons.
535-35
-------
TABLE 4. ION TRAP MS/MS METHOD CONDITIONS
Segment
#b
1
2
3
4
5
6
7
7
8
8
8
9
4
10
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Dimethachlor ESA (SUR) f
Butachlor ESA (IS)
Retention
Time (min)
11.20
11.95
12.58
13.01
13.43
14.34
15.27
16.46
16.97
18.99
19.24
19.39
13.38
29.26
Precursor
Ion (m/z) c
206
224
256
274
270
320
264
264
314
278
314
328
300
356
Product
Ion (m/z) d'e
134
152
121
121
198
121
160g
146s
121
206
121
121
121
121
Normalized
Collision
Energy (%)
28
28
36
36
28
36
28
28
36
28
36
36
36
36
a An ion trap LC/MS/MS chromatogram of the analytes is shown in Figure 1.
b Segments are time durations in which single or multiple scan events occur.
c Isolation width was ±3 daltons
Ions used for quantitation purposes.
e Scan width was ±2 daltons.
Analyte has two partially resolved chromatographic peaks due to stereoisomers. Both peaks
summed for quantitation purposes.
8 Scan range was 145-161 daltons.
535-36
-------
TABLE 5. DETECTION LIMITS AND LOWEST CONCENTRATION MRL IN REAGENT WATER
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Triple Quadrupole MS a
DL Fortification
Level (|ug/L)
0.20
0.10
0.23
0.21
0.18
0.24
0.20
0.25
0.20
0.20
0.18
0.23
DLcOig/L)
0.093
0.057
0.11
0.099
0.063
0.093
0.12
0.11
0.082
0.090
0.095
0.11
LCMRLd
fog/L)
0.55
0.22
0.40
0.35
0.41
0.45
0.52
0.48
0.32
0.44
0.41
0.40
Ion Trap MS b
DL Fortification
Level (jig/L)
0.080
0.010
0.020
0.020
0.020
0.040
0.040
0.040
0.020
0.010
0.020
0.080
DLc(ug/L)
0.036
0.012
0.010
0.0060
0.013
0.029
0.032
0.019
0.0080
0.010
0.012
0.043
LCMRLd
fog/L)
0.10
0.016
0.035
0.034
0.031
0.048
0.076
0.074
0.032
0.017
0.030
0.11
a Samples extracted manually and analyzed using conditions in Table 3.
Samples extracted by automation and analyzed using conditions in Table 4.
c Detection Limits were determined by analyzing 7 replicates over 3 days using the conditions outlined in Tables 1-4.
d LCMRLs were calculated according to the procedure in reference 1.
535-37
-------
TABLE 6. PRECISION AND ACCURACY OF LOW LEVEL FORTIFIED REAGENT WATER
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Dimethachlor (SUR)
Triple Quadrupole MS a
Fortification
Level (jig/L)
0.50
0.26
0.59
0.54
0.45
0.59
0.50
0.62
0.51
0.49
0.44
0.58
1.8
Mean %
Recovery
89
88
89
88
74
78
76
82
83
77
84
87
94
RSD (%)
7.5
6.3
11
9.3
12
15
3.9
4.7
7.2
6.0
5.8
7.0
7.8
Ion Trap MS b
Fortification
Level (jig/L)
0.16
0.020
0.040
0.040
0.040
0.080
0.080
0.080
0.040
0.020
0.040
0.16
0.48
Mean %
Recovery
98
103
103
108
98
98
93
99
108
91
103
101
108
RSD (%)
3.9
15
14
14
16
7.7
17
15
13
16
13
10
7.6
1 Samples (N=7) extracted manually and analyzed using conditions in Table 3.
' Samples (N=7) extracted by automation and analyzed using conditions in Table 4.
535-38
-------
TABLE 7. PRECISION AND ACCURACY OF HIGH LEVEL FORTIFIED REAGENT WATER
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Dimethachlor (SUR)
Triple Quadrupole MS a
Fortification
Level (|ug/L)
2.0
1.0
2.3
2.1
1.8
2.4
2.0
2.5
2.0
2.0
1.7
2.3
1.8
Mean %
Recovery
89
90
100
98
85
94
80
82
92
85
96
94
95
RSD (%)
5.8
4.2
1.8
1.4
3.3
3.1
6.2
4.6
2.4
6.5
3.3
2.8
1.6
Ion Trap MS b
Fortification
Level (jig/L)
0.80
0.10
0.20
0.20
0.20
0.40
0.40
0.40
0.20
0.10
0.20
0.80
0.48
Mean %
Recovery
102
106
106
104
96
108
80
88
100
91
108
104
100
RSD (%)
3.6
3.2
3.9
3.5
7.1
6.0
9.9
9.9
5.3
12
7.7
9.4
5.6
1 Samples (N=7) extracted manually and analyzed using conditions in Table 3.
' Samples (N=6) extracted by automation and analyzed using conditions in Table 4.
535-39
-------
TABLE 8. PRECISION AND ACCURACY IN CHLORINATED SURFACE WATER
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Dimethachlor (SUR)
Triple Quadrupole MS b
Fortification
Level (|ug/L)
1.5
0.78
1.8
1.6
1.4
1.8
1.5
1.9
1.5
1.5
1.3
1.7
1.8
Mean %
Recovery
63
68
81
85
73
82
84
83
80
69
80
72
81
RSD (%)
1.4
2.0
2.4
1.7
1.4
2.4
1.8
1.8
2.0
2.7
1.9
3.8
1.2
Ion Trap MS c
Fortification
Level (jig/L)
0.80
0.10
0.20
0.20
0.20
0.40
0.40
0.40
0.20
0.10
0.20
0.80
0.48
Mean %
Recovery
132
158
93
103
99
106
97
103
119
89
117
106
100
RSD (%)
12
14
6.0
1.8
8.8
3.3
11
10
4.3
4.7
2.9
2.0
5.6
a TOC = 1.6 mg/L and hardness = 120 mg/L.
b Samples (N=6) extracted manually and analyzed using conditions in Table 3.
c Samples (N=4) extracted by automation and analyzed using conditions in Table 4.
535-40
-------
TABLE 9. PRECISION AND ACCURACY IN HIGH TOC CHLORINATED SURFACE WATER
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Dimethachlor (SUR)
Triple Quadrupole MS b
Fortification
Level (|ug/L)
1.5
0.78
1.8
1.6
1.4
1.8
1.5
1.9
1.5
1.5
1.3
1.7
1.8
Mean %
Recovery
33
42
87
91
60
82
63
64
87
67
89
77
83
RSD (%)
4.0
4.5
2.4
2.7
2.4
3.0
3.0
3.1
2.9
3.8
2.8
3.0
2.4
Ion Trap MS c
Fortification
Level (jig/L)
0.80
0.10
0.20
0.20
0.20
0.40
0.40
0.40
0.20
0.10
0.20
0.80
0.48
Mean %
Recovery
75
96
71
84
83
73
88
73
74
122
84
109
86
RSD (%)
11.6
10.1
6.5
8.8
6.1
4.2
4.5
8.6
9.4
2.5
6.6
5.6
4.1
a TOC = 8.6 mg/L.
b Samples (N=7) extracted manually and analyzed using conditions in Table 3.
c Samples (N=4) extracted by automation and analyzed using conditions in Table 4.
535-41
-------
TABLE 10. SAMPLE HOLDING TIME DATA (N=7) FOR CHLORINATED GROUND WATER SAMPLES
a,b
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Fortification
Level (|ug/L)
0.80
0.10
0.20
0.20
0.20
0.40
0.40
0.40
0.20
0.10
0.20
0.80
DayO
Mean %
Recovery
95
116
106
101
105
105
94
100
89
91
91
97
RSD (%)
3.7
2.4
3.6
4.9
1.8
1.3
5.3
4.1
4.9
4.1
5.0
4.9
Day 7
Mean %
Recovery
112
128
112
112
107
108
102
103
105
96
104
104
%RSD
6.3
4.5
5.0
6.2
6.0
4.3
5.9
4.8
1.9
5.6
6.9
4.5
Day 14
Mean %
Recovery
107
128
102
107
108
100
100
96
93
90
82
97
RSD (%)
10
8.2
9.4
7.9
4.9
5.8
10
8.3
3.3
4.5
5.9
4.7
a TOC = 1.6 mg/L and hardness =360 mg/L.
b Samples dechlorinated, extracted by automation and analyzed using ion trap conditions in Table 4.
535-42
-------
TABLE 11. EXTRACT HOLDING TIME DATA (N=7) FOR CHLORINATED GROUND WATER SAMPLES
a,b
Analyte
Propachlor OA
Flufenacet OA
Propachlor ESA
Flufenacet ESA
Dimethenamid OA
Dimethenamid ESA
Alachlor OA
Acetochlor OA
Alachlor ESA
Metolachlor OA
Acetochlor ESA
Metolachlor ESA
Dimethachlor (SUR)
Fortification
Level (|ug/L)
0.80
0.10
0.20
0.20
0.20
0.40
0.40
0.40
0.20
0.10
0.20
0.80
0.48
DayO
Mean
%Rec
95
116
106
101
105
105
94
100
89
91
91
97
102
RSD
(%)
3.7
2.4
3.6
4.9
1.8
1.3
5.3
4.1
4.9
4.1
5.0
4.9
3.9
Day 7
Mean
%Rec
98
112
93
102
98
102
86
86
100
81
92
102
94
RSD
(%)
4.7
4.6
4.5
6.6
3.7
6.3
7.3
11.1
6.4
5.7
6.1
4.9
5.8
Day 14
Mean
%Rec
99
121
95°
107
111
102
101
112
105
103
97
107
103
RSD
(%)
5.5
3.9
4.3
4.2
1.8
3.4
7.2
5.7
5.1
2.7
5.5
4.6
6.7
Day 21
Mean
%Rec
100
114
92C
97
103
97
100
97
94
92
93
98
101
RSD
(%)
5.0
3.0
7.7
7.4
4.6
7.6
9.8
8.9
6.4
4.0
3.9
3.1
6.3
Day 28
Mean
%Rec
95
112
100
100
106
95
104
102
106
101
88
98
103
RSD
(%)
6.1
4.4
6.0
5.5
6.6
4.4
11.4
8.8
4.3
7.6
4.7
5.3
6.1
a TOC = 1.6 mg/L and hardness =360 mg/L.
b Samples dechlorinated, extracted by automation and analyzed using ion trap conditions in Table
CN=6
4.
535-43
-------
TABLE 12. INITIAL DEMONSTRATION OF CAPABILITY (IDC) REQUIREMENTS
Method
Reference
Requirement
Specification and Frequency
Acceptance Criteria
Sect. 9.2.1
Initial Demonstration of
Low System Background
Analyze LRB prior to any other IDC steps, or
anytime a new lot of SPE materials or
reagents are used.
Demonstrate that all target analytes are
-------
TABLE 13. QUALITY CONTROL REQUIREMENTS (SUMMARY)
Method
Reference
Requirement
Specification and Frequency
Acceptance Criteria
Sect. 8.1
Sect 8.4
Sample Collection,
Preservation and
Holding Time
14 days, protected from light, with addition
of ammonium chloride.
Iced or refrigerated at 10 °C or less for up to 48 hours
to allow time for shipping; refrigerated at 6 °C or less
after arrival at the laboratory.
Sect. 8.4
Extract Holding
28 days
Stored at 4 °C or less in amber vials.
Sect. 9.3
Laboratory Reagent
Blank (LRB)
Include a LRB with each extraction batch
(up to 20 samples). Analyze prior to
analyzing samples and determine to be free
from interferences.
Demonstrate that all target analytes are below 1/3 the
MRL, and that possible interference from reagents and
glassware do not prevent the identification and
quantitation of target analytes.
Sect. 9.4 and
Sect. 10.3
Continuing
Calibration Check
(CCC)
Verify initial calibration by analyzing a low
level (at the MRL or below) CCC prior to
analyzing samples. CCCs are then injected
after every 10 samples and after the last
sample, rotating concentrations to cover the
calibrated range of the instrument.
Recovery for each analyte must be within 70-130% of
the true value for all but the lowest level of calibration.
The lowest calibration level CCC must be within
50-150% of the true value.
Sect. 9.5
Laboratory Fortified
Blank (LFB)
Analyze at least one LFB daily or one for
each extraction batch of up to 20 field
samples. Rotate the fortified concentration
between low, medium and high amounts.
Results of LFB analyses must be 70-130% of the true
value for each analyte and surrogate for all fortified
concentrations greater than the lowest CAL point.
Results of LFBs corresponding to the lowest CAL point
must be 50-150% of the true value.
Sect. 9.6
Internal Standard (IS)
Butachlor ESA is added to all standards
and extracts.
Peak area counts of the IS in LFBs, LRBs and sample
extracts must be within 50-150% of the average peak
area in the initial calibration.
535-45
-------
Method
Reference
Requirement
Specification and Frequency
Acceptance Criteria
Sect. 9.7 Surrogate Standards
(SUR)
The surrogate, dimethachlor ESA, is added
to all calibration standards, samples, LFBs,
LFSMs, LFSMDs, FDs, and LRBs.
Surrogate recovery must be within 70-130% of the true
value.
Samples that fail criteria, must be reported as suspect
due to surrogate recovery or potential matrix effect.
Sect. 9.8 Laboratory Fortified
Sample Matrix
(LFSM)
Analyze one LFSM per extraction batch
(20 field samples or less) fortified with
method analytes at a concentration > the
native concentration.
Recoveries not within 60-140% (50-150% at the MRL)
of the fortified amount may indicate a matrix effect.
Sect. 9.9 Field Duplicates (FD)
or Laboratory
Fortified Sample
Matrix Duplicates
(LFSMD)
Analyze 1 FD for each 20 samples, or 1 per
extraction batch, whichever is greater. See
the referenced section for a discussion of
when LFSMDs should be analyzed.
RPDs should be within 0-30%.
Sect. 9.10
Resolution Check
Monitor once for every 24 hour analysis
period.
Alachlor ESA and acetochlor ESA that are not baseline
resolved must have a resolution of 1.0 or greater using
the equation in Sect. 9.10.
Sect. 9.11 Quality Control
Sample (if available)
Analyze at least quarterly or when
preparing new standards, as well as during
the IDC.
If analyzed as a calibration sample, CCC criteria apply.
If analyzed as an LFB, those criteria apply.
Sect. 10.2
Initial Calibration
Use internal standard calibration technique
to generate an average RF, or first or
second order calibration curve for each
analyte. Use a minimum of 5 CAL
standards.
When each calibration standard is calculated using the
calibration curve, the results should be 70-130% of the
true value for all but the lowest standard. The lowest
standard should be 50-150% of the true value.
535-46
-------
iOOQOQQ -
4000000 -
3000000 -
2000000 -
1000000 -
0 -
1200000
1000000 •
800000-
600000-
400000-
200000-
11
SUR
12
13
14
•~i
16
12
IS
18
22
Time (min)
24
26
28
30
Target Peaks
1 propachlor OA
2 flufenacet OA
3 prop achlor E SA
4 flufenacet E SA
5 dimethenamid OA
6 dimethenamid ESA
TalachlnrOA
8 acetochlor OA
9alachlorESA
10 metolachbr OA
11 acetochlor ESA
12 metolachbr ESA
Figure 1. Ion trap LC/MS/MS chromatogram of a standard containing the target analytes at the concentrations listed in
Table 10. Note there some of the analytes (SUR, 5, and 6) have two partially resolved peaks due to
steroisomers.
535-47
-------
METHOD 535 APPENDIX A
A.1 SCOPE AND APPLICATION
This appendix is intended to be used to synthesize butachlor ESA, which is the suggested
internal standard (IS) used in Method 535. During method development, the following
directions, adapted from Feng," were used to synthesis the IS; however, these directions
are not intended to be restrictive. The following steps maybe modified provided the
MS/MS mass spectrum matches that provided in Figure Al and that no contaminant peaks
are present which could interfere in the quantitation of the target analytes.
A.2 SAFETY
A.2.1 The toxicity or carcinogenicity of each reagent used in this appendix has not been
precisely defined; each chemical reagent should be treated as a potential health
hazard, and exposure to these chemicals should be minimized. The laboratory is
responsible for maintaining a current awareness file of OSHA regulations
regarding the safe handling of the chemicals specified in this appendix. A
reference file of MSDSs should also be made available to all personnel involved in
the chemical analysis.
A.2.2 Pure standard materials and stock standards should be handled with suitable
protection to skin and eyes. Care should be taken not to breathe the vapors or
ingest the materials.
A.2.3 At a minimum, the refiuxing, acidification and separatory funnel extractions
should be performed in a chemical hood.
A.3 EQUIPMENT AND SUPPLIES (Brand names and/or catalog numbers are included for
illustration only, and do not imply endorsement of the product.)
A.3.1 GLASSWARE - All glassware must be meticulously cleaned. Wash glassware
with detergent and tap water, rinse with tap water, followed by reagent water. A
final rinse with solvents may be needed. In place of a solvent rinse,
non-volumetric glassware can be heated in a muffle furnace at 400 °C for 2 hours.
Volumetric glassware should not be heated above 120 °C.
A.3.2 GRADUATED CYLINDERS - Various sizes.
A.3.3 BALANCE - Analytical, capable of accurately weighing to 0.0001 g.
A.3.4 DISPOSABLE PIPETTES - Various sizes, used to transfer solutions.
Feng, P.C.C. (1991) Pestic. Biochem. Physiol. 40, 136-142.
535-48
-------
A.3.5 DRYING OF THE PRODUCT
A.3.5. 1 VACUUM DESICCATOR - To dry the synthesized product (Fisher
Cat.# 08-632 or equivalent).
A.3.5.2 FREEZE DRYER (OPTIONAL) - To dry the synthesized product
(Labconco, Freeze Dry System/Freezone 4.5, Cat. # 77510-OON or
equivalent).
A.3.6 ROUND BOTTOM OR FLAT BOTTOM FLASK - 50-mL pyrex flask (or
equivalent) to contain and reflux the reactants.
A.3.7 FRIEDRICH CONDENSER - 250 mL, used to prevent evaporation losses during
refluxing (Kimble-Kontes Cat.# 456250-0022 or equivalent).
A.3 . 8 SEPARATORY FUNNEL - 60 mL, used in the liquid-liquid extraction of the
synthesized IS after refluxing.
A.3. 9 HEATING MANTLE - Sized to fit and heat a 50-mL flask to 85-95 °C.
A.3. 10 EXTRACT CONCENTRATION SYSTEM - Synthesized product is concentrated
by blowdown with nitrogen using a water bath set at 60-65 °C (Meyer N-EVAP,
model 111, Organomation Associates, Inc. or equivalent).
A.4 REAGENTS AND GASES
A.4. 1 BUTACHLOR (C17H26C1NO2, CAS#: 23 1 84-66-9) - Reactant in IS synthesis
(Supelco, Cat. #PS-348 or equivalent).
A.4.2 ETHANOL (C2H6O, CAS#: 64-17-5) - >190 proof (Sigma Cat.# E7148 or
equivalent).
A.4.3 BOILING CHIP S (CAS#: 1344-28-1) - Used in refluxing step (Fisher Cat.# B365,
or equivalent). A stir bar and stir plate can be used in place of the boiling chips, if
preferred.
A.4.4 SODIUM SULFITE (Na^Og, CAS#: 7757-83-7) - Reactant in IS synthesis (Fisher
Cat.# S-447 or equivalent).
A.4.5 SULFURIC ACID (H2SO4, CAS#:7664-93-9) - Used to acidify synthesized IS
before extracting (Fisher Cat.# A300-500 or equivalent).
A.4.6 METHYLENE CHLORIDE (CH2C12, CAS#: 75-09-2) - Extraction solvent (Fisher
Cat.# D151 or equivalent).
535-49
-------
A.4.7 NITROGEN - Used to evaporate the methylene chloride (Ultra High Purity or
equivalent).
A.4.8 REAGENT WATER - Purified water which does not contain any measurable
quantities of any target analytes.
A.5 SYNTHESIS OF BUTACHLOR ESA
A.5.1 Add 13.5 mL of reagent water to a 50-mL round-bottom flask with a few boiling
chips.
A.5.2 Add 1.5 mL of ethanol to the flask.
A.5.3 Add 0.5g of butachlor and 3g of sodium sulfite to the flask containing the ethanol
and water. Not all the butachlor and sodium sulfite will be soluble and the solution
may look cloudy.
A.5.4 Gently heat and reflux the solution overnight (-20 hours). The solution will
become clear during the refluxing.
A.5.5 After refluxing, allow the solution to cool. Add 2 mL of concentrated sulfuric acid
to the round-bottom flask containing the refluxed and cooled solution. At this
point the solution will become milky white in appearance.
A.5.6 Transfer the reaction solution to a 60-mL separatory funnel with a disposable
pipette. Wash the round-bottom flask with several milliliters of reagent water and
transfer the washes to the separatory funnel.
A.5.7 Add 20 mL of methylene chloride to the separatory funnel. Shake the funnel for
approximately 2 minutes with frequent venting. A milky white emulsion will
form. Allow the phases to separate for approximately 24 hours. The emulsion
should separate into 2 phases: a methylene chloride phase and a water phase. If the
emulsion has not cleared, allow the phases to stand longer until separation is
complete.
A.5.8 Obtain the dry weight of the collection apparatus (beaker, tube, etc.) and collect the
bottom layer (methylene chloride layer) of the separatory funnel. Discard the water
fraction.
A.5.9 Evaporate the methylene chloride to dryness in a nitrogen evaporator at room
temperature. After evaporation the residue will appear viscous. Weigh the
residue.
535-50
-------
A.5.10 Place the residue in a vacuum desiccator. Dry the product until a constant weight
is achieved. This may take several weeks. Other methods of evaporation (such as
freeze drying) are also acceptable.
A.6 VERIFICATION OF BUTACHLOR ESA
A.6.1 Follow the procedure in Sect. 7.2.1 of Method 535 to prepare an IS PDS solution
of the IS near a concentration of 10 ug/mL in methanol.
A.6.2 Using the IS PDS, prepare a "calibration standard" containing only the synthesized
IS at an appropriate concentration. During method development, the IS
concentration in standards and extracts was 80 ug/L.
A.6.3 Tune the LC/MS using the procedures outline in Section 10.2.1.1 and 10.2.1.2 of
Method 535.
A.6.4 Initially, perform a full scan LC/MS run to locate the IS peak and verify the
molecular weight (butachlor ESA MW=357). Set the MS to scan at least
200-400 daltons in the negative ion ESI mode.
A.6.5 Inject an aliquot of the "calibration standard" into the LC/MS using the suggested
LC parameters outlined in Section 17, Table 1 of Method 535. Other LC
conditions may be used at the discretion of the analyst. If other LC conditions are
used, more emphasis will have to be placed on the interpretation of the mass
spectra since the IS retention time will not match the retention time demonstrated
in Method 535.
A.6.6 Locate the chromatographic peak containing the [M-H]~ ion at m/z 356. Note the
retention time. In addition, carefully observe the whole chromatogram and verify
that no other peaks (contaminants) are present which will interfere in the analysis
of the other target analytes. Since the final analysis is MS/MS, the main concern at
this point should be whether any potential contaminants are present in large enough
quantities to cause suppression in the electrospray source. A suggested guideline
is: if the contaminant is present at lOx the IS level, it may cause suppression of a
co-eluting target analyte. If such a contaminant is present, further purification of
the synthesized IS may be necessary. Figure Al-A and Al-B demonstrate the
relative purity of the synthesized standard. A full scan mass spectra of synthesized
butachlor ESA is demonstrated in Figure Al-C.
A.6.7 Optimize the LC/MS/MS using the procedures outlined in Section 10.2.1.3 of
Method 535 Confirm the identity of the synthesized IS with LC/MS/MS by
scanning all products ions produced by fragmentation of m/z 356. Suggested
MS/MS parameters are found in Tables 3 or 4 of Method 535. Obtain a full scan
MS/MS by scanning the product ions over a mass range of 75-357 daltons, if
possible. (Ion trap instruments may not be able to scan this large of a mass range.
535-51
-------
In that case, use the lowest starting mass the ion trap will allow.) A product ion
mass spectra of synthesized butachlor ESA is demonstrated in Figure A2 using an
ion trap instrument. MS/MS fragmentation and relative abundances can vary
significantly between instruments and depends heavily on various instrument
settings. At a minimum, m/z 121 must be present in the synthesized IS and if a
triple quadrupole instrument is used, m/z 80 must be present. Other ions present in
Figure A2 should be used, at the discretion of the analyst, to further verify the
synthesis of the IS.
535-52
-------
A) Full Son LC MS
25.13
JL
29.34
_ K
31 .55
-------
1DD -3
90 -
70 -=
60 -
Js
cc. 40
30 -
20 -
10 -
0 -
121
176
158
149
122
I.
160
356
357
218
282 287
100
120
140
160
180
200
220
240
260
280
300
320
340
360
Figure A2. Product ion mass spectrum of m/z 356 used for confirmation of synthesized butachlor ESA using an ion trap mass
spectrometer.
535-54
-------
Method 535 APPENDIX B
B.I SCOPE AND APPLICATION
This appendix is intended to be used to synthesize dimethachlor ESA which is the
suggested surrogate (SUR) standard used in Method 535. During method development,
the following directions, adapted from Feng,a were used to synthesis the SUR; however,
these directions are not intended to be restrictive. The following steps may be modified
provided the MS/MS mass spectrum matches that provided below and that no contaminant
peaks are present which could interfere in the quantitation of the target analytes.
B.2 SAFETY
B.2.1 The toxicity or carcinogenicity of each reagent used in this appendix has not been
precisely defined; each chemical reagent should be treated as a potential health
hazard, and exposure to these chemicals should be minimized. The laboratory is
responsible for maintaining a current awareness file of OSHA regulations regarding
the safe handling of the chemicals specified in this appendix. A reference file of
MSDSs should also be made available to all personnel involved in the chemical
analysis.
B.2.2 Pure standard materials and stock standards of these compounds should be handled
with suitable protection to skin and eyes. Care should be taken not to breathe the
vapors or ingest the materials.
B.2.3 At a minimum, the refluxing, acidification and separatory funnel extractions should
be performed in a chemical hood.
B.3 EQUIPMENT AND SUPPLIES (Brand names and/or catalog numbers are included for
illustration only, and do not imply endorsement of the product.)
B.3.1 GLASSWARE - All glassware must be meticulously cleaned. Wash glassware
with detergent and tap water, rinse with tap water, followed by reagent water. A
final rinse with solvents maybe needed. In place of a solvent rinse, non-volumetric
glassware can be heated in a muffle furnace at 400 °C for 2 hours. Volumetric
glassware should not be heated above 120 °C.
B.3.2 GRADUATED CYLINDERS - Various sizes.
B.3.3 BALANCE - Analytical, capable of accurately weighing to 0.0001 g.
Feng, P.C.C. (1991) Pestic. Biochem. Physiol 40, 136-142.
535-55
-------
B.3.4 DISPOSABLE PIPETTES - Various sizes, used to transfer solutions.
B.3.5 CONICAL COLLECTION TUBES -15 mL and 50 mL, or other glassware suitable
for collection of the eluent from the solid phase cartridge after extraction of the
synthesized SUR.
B.3.6 SOLID PHASE EXTRACTION (SPE) APPARATUS USING CARTRIDGES
B.3.6.1 SPE CARTRIDGES - 5.0 g, 20 mL SPE cartridges containing a
nonporous graphitized carbon sorbent phase (Supelclean ENVI-Carb SPE
cartridges, Supelco Catalog No. 57129 or equivalent).
B.3.6.2 VACUUM EXTRACTION MANIFOLD - A manual vacuum manifold
(Supelco Cat. No. 57030 and 57275 or equivalent) for cartridge
extractions.
B.3.6.3 LABORATORY OR ASPIRATOR VACUUM SYSTEM - Sufficient
capacity to maintain a vacuum of approximately 25 cm (10 in) of mercury.
B.3.7 DRYING OF THE PRODUCT
B.3.7.1 VACUUM DESICCATOR - To dry the synthesized product (Fisher
Cat.# 08-632 or equivalent).
B.3.8 ROUND BOTTOM OR FLAT BOTTOM FLASK - 50-mL pyrex flask (or
equivalent) to contain and reflux the reactants.
B.3.9 FRIEDRICH CONDENSER - 250 mL, used to prevent evaporation losses during
refluxing (Kimble-Kontes Cat.# 456250-0022 or equivalent).
B.3.10 HEATING MANTLE - Sized to fit and heat a 50-mL flask to 85-95 °C.
B.3.11 EXTRACT CONCENTRATION SYSTEM - Extracts are concentrated by
blowdown with nitrogen using a water bath set at 60-65 °C (Meyer N-EVAP,
model 111, Organomation Associates, Inc. or equivalent).
B.4 REAGENTS AND GASES
B.4.1 DIMETHACHLOR (C13H18C1NO2, CAS#: 50563-36-5) - Reactant in SUR
synthesis (Sigma-Aldrich, Cat. #45447 or equivalent).
B.4.2 ETHANOL (C2H6O, CAS#: 64-17-5) - >190 proof (Sigma Cat.#E7148 or
equivalent).
535-56
-------
B.4.3 METHANOL (CH3OH, CAS#: 67-56-1) - High purity, demonstrated to be free of
target analytes and interferences (Fisher Optima grade or equivalent).
B.4.4 AMMONIUM ACETATE (NH4C2H3O2, CAS#: 631-61-8) -High purity,
demonstrated to be free of analytes and interferences (Sigma- Aldrich ACS grade or
equivalent).
B.4.5 10 mM AMMONIUM ACETATE/METHANOL - To prepare 1L, add 0.7708 g
ammonium acetate to 1L of methanol. During method development, this solution
was shown to be stable for at least 18 days.
B.4.6 BOILING CHIP S (CAS#: 1344-28-1) - Used in refiuxing step (Fisher Cat.# B365,
or equivalent). A stir bar and stir plate can be used in place of the boiling chips, if
preferred.
B.4.7 SODIUM SULFITE (NajSOg, CAS#: 7757-83-7) - Reactant in SUR synthesis
(Fisher Cat.# S-447 or equivalent).
B.4.8 NITROGEN - Used to evaporate the methylene chloride (Ultra High Purity or
equivalent).
B.4.9 REAGENT WATER - Purified water which does not contain any measurable
quantities of any target analytes.
B.5 SYNTHESIS OF DIMETHACHLOR ESA
B.5.1 Add 13.5 mL of reagent water to a 50-mL round-bottom flask with a few boiling
chips.
B.5. 2 Add 1.5 mL of ethanol to the flask.
B.5. 3 Add 0.25 g of dimethachlor and 1.5 g of sodium sulfite to the flask containing the
ethanol and water.
B.5. 4 Gently heat and reflux the solution overnight (-20 hours).
B.5. 5 Allow the refluxed solution to cool. Divide the 15-mL refiuxed solution into two
approximately equal portions. Prepare two SPE cartridges according to the
procedure in Section B. 5.6.1 and extract each portion on the cartridges according to
the procedure in Section B5.6.2.
B.5.6 MANUAL CARTRIDGE SPE PROCEDURE
535-57
-------
B.5.6.1 CARTRIDGE CLEAN-UP AND CONDITIONING - DO NOT allow
cartridge packing material to go dry during any of the conditioning steps.
Rinse each cartridge with 60 mL of 10 mM ammonium acetate/methanol
(Sect. B.4.5). Next, rinse each cartridge with 120 mL of reagent water,
without allowing the water to drop below the top edge of the packing. If
the cartridge goes dry during the conditioning phase, the conditioning must
be started over. Leave a small layer of reagent water on the top of the
cartridge. Begin adding the synthesized SUR solution to the cartridge.
B.5.6.2 SAMPLE EXTRACTON - Adjust the vacuum so that the approximate
flow rate is 5 mL/min. Do not allow the cartridge to go dry before all the
solution has passed through. After all of the solution has passed through
the cartridge, rinse the cartridge with 50 mL of reagent water and draw air
or nitrogen through the cartridge for 5 min at high vacuum (10-15 in. Hg).
Note: If the reagent water rinse is not performed, substantial residual
sodium sulfite remaining in the cartridge will be eluted with the SUR.
Sodium sulfite is not soluble in methanol thus a white precipitate will be
observed. In this case, the extract will have to be taken to dryness,
reconstituted in reagent water and re-extracted according to Section B.5.6.
B.5.6.3 CARTRIDGE ELUTION - Lift the extraction manifold top and insert a
rack with two 50-mL collection tubes into the extraction tank to collect the
extracts as they are eluted from the cartridge. Elute the analytes from the
cartridge with 50 mL of 10 mM ammonium acetate/methanol at a low
vacuum (~5 mL/min), such that the solvent exits the cartridge in a
dropwise fashion.
B.5.7 EXTRACT CONCENTRATION - Concentrate the extracts under a gentle stream
of nitrogen in heated water bath (60-65 °C) to 3-5 mL each. Weigh a 15-mL
collection tube. Transfer the two extracts to the weighed 15-mL collection tube
rinsing with 2-3 mL of 10 mM ammonium acetate/methanol. Evaporate the extract
to dryness. Due to the amount of water (from the cartridges) in the extracts, the
evaporation process will take in excess of 24 hours. After evaporation the clear
residue will appear viscous. Weigh the residue.
B.5.8 Place the residue in a vacuum desiccator. Periodically weigh the residue. Continue
drying until constant weight is achieved. This may take several weeks.
B.6 VERIFICATION OF DIMETHACHLOR ESA
B.6.1 Follow the procedure in Section 7.2.2 of the method to prepare a SUR PDS solution
of the SUR near a concentration of 24 ug/mL in methanol.
535-58
-------
B.6.2 Using the SUR PDS, prepare a "calibration standard" containing only the
synthesized SUR at an appropriate concentration. During method development, the
SUR concentration in standards and extracts was 120 ug/L.
B.6.3 Tune the LC/MS using the procedures outline in Section 10.2.1.1 and 10.2.1.2 of
Method 535.
B.6.4 Initially, perform a full scan LC/MS run to locate the SUR peak and verify the
molecular weight (dimethachlor ESA MW=301). Set the MS to scan at least
200-400 daltons in the negative ion ESI mode.
B.6.5 Inject an aliquot of the "calibration standard" into the LC/MS using the suggested
LC parameters outlined in Section 17, Table 1 of the Method 535. Other LC
conditions may be used at the discretion of the analyst. If other LC conditions are
used, more emphasis will have be placed on the interpretation of the mass spectra
since the SUR retention time will not match the retention time demonstrated in
Method 535.
B.6.6 Locate a chromatographic peak containing an [M-H]~ at m/z 300. Note the retention
time. In addition, carefully observe the whole chromatogram and verify that no
other peaks (contaminants) are present which will interfere in the analysis of the
other target analytes. Since the final analysis is MS/MS, the main concern at this
point should be whether any potential contaminants are present in large enough
quantities to cause suppression in the electrospray source. A suggested guideline is,
if the contaminant is present at lOx the SUR level, it may cause suppression of a
co-eluting target analyte. If such a contaminant is present, further purification of the
synthesized SUR maybe necessary. Figure Bl-A and Bl-B demonstrate the
relative purity of the synthesized standard. A full scan mass spectra of synthesized
dimethachlor ESA is demonstrated in Figure Bl-C.
B.6.7 Optimize the LC/MS/MS using the procedures outlined in Section 10.2.1.3 of
Method 535. Confirm the identity of the synthesized SUR with LC/MS/MS by
scanning all products ions produced by fragmentation of m/z 300. Suggested
MS/MS parameters are found in Tables 3 or 4 of the Method 535. Obtain a full
scan MS/MS by scanning the product ions over a mass range of 75-305 daltons, if
possible. (Ion trap instruments may not be able to scan this large of a mass range.
In that case, use the lowest mass the ion trap will allow.) A product ion mass
spectra of synthesized dimethachlor ESA is demonstrated in Figure B2 using a triple
quadrupole instrument. MS/MS fragmentation and relative abundances can vary
significantly between instruments and depends heavily on various instrument
settings. At a minimum, m/z 121 must be present in the synthesized SUR and if a
triple quadrupole instrument is used, m/z 80 must be present. Other ions present in
Figure B2 should be used, at the discretion of the analyst, to further verify the
synthesis of the SUR. Note: m/z 212 was not observed in the ion trap product ion
mass spectrum of dimethachlor ESA.
535-59
-------
loo 12.30
A) Full Scan LC/MS
rtV*«^Wfr>i>&-^*^^
12.3O
>-
IS
B) m/z 300
1O rr^- ,- - ^ 15
Time (mm)
3OO
[M-H] of dimethachlor ESA
C) TVIass spectrum of peak at 12.3O iiiin
21 1
200 220 240 2CO
280 300
m/z
320 340 360 38O
Figure Bl. LC/MS ananlysis of synthesized dimethachlor ESA demonstrating purity and confirmation of the molecular weight
using a triple quadrupole mass spectrometer.
535-60
-------
300
212
121
12O 14O 16O ISO 2OO
22O 240
m/z
26O 28O 30O 320 34O 36O 38O 4OO
Figure B2. Product ion mass spectrum of m/z 300 used for confirmation of synthesized dimethachlor ESA using a triple
quadrupole mass spectrometer.
535-61
------- |