US EPA Designated
^SmartWay
U.S. EPA Designated SmartWay Mark
License Agreement,Technical Specifications & Requirements, and
Graphics Standards & Usage Guide for
Tractor & Trailer Manufacturers
a BOOB
"QDOBQ
U.S. EPA SmartWay | EPA420-BII-OI3 | www.epa.gov/smartway
-------
Trademark License Agreement
For Use of U.S. ENVIRONMENTAL PROTECTION AGENCY SmartWay Mark by
(name of licensee or Original Equipment Manufacturer)
Whereas the United States Environmental Protection Agency ("EPA", "Agency" or
"Licensor") is the owner of the U.S. ENVIRONMENTAL PROTECTION AGENCY SMARTWAY mark
("Mark"), which the Licensee will use to identify tractors or trailers that meet fuel efficiency and
emissions standards established by the Agency; and
Whereas the (name of licensee) ("(name)" or "Licensee") intends to display the Mark in
connection with its tractors or trailers that meet the requirements for displaying the Mark; and
Whereas Licensee also wishes to assist the Agency in its official recognition efforts by
using the Mark in marketing and outreach efforts to help promote public knowledge and
acceptance of the Mark.
Now, therefore, in consideration of the mutual promises herein contained, it is agreed
that:
i. Grant of License: The Licensor hereby grants to the Licensee a non-exclusive, royalty-
free right to use the Mark in the following manner:
Only on or in connection with the sale of tractors or trailers that meet the specifications
established by Licensor which are attached to this agreement and entitled Technical
Specifications & Requirements for Using US EPA's SmartWay Mark on Qualifying Tractors and
Trailers.
2. Quality Control: The Licensor shall have the right, at all reasonable times, to inspect
the Licensee's goods, services and promotional activities employing the Mark to ensure that such
use is of proper quality and otherwise consistent with this Agreement. The Licensee agrees that
it will display the Mark only in a manner that complies with the attached SmartWay Graphic
Standards and Logo Usage Guide.
3. Duration and Termination: This Agreement shall terminate 3 years from the date of
its signature by both parties. The Licensee, however, may renew this Agreement for an additional
term of 2 years with the written consent of Licensor. Such consent shall be in the form of a
properly executed Renewal Agreement signed by authorized signatories of the Parties.
Upon termination of this Agreement, all rights of the Licensee to use the Mark shall
immediately terminate. In the event of a breach of any of the terms and conditions of this
License by the Licensee, the Licensor shall give Licensee written notice of such breach. In the
event Licensee does not cure such breach within thirty (30) days, Licensor may immediately
terminate this License and shall notify the Licensee in writing of such termination.
4. Assignments and Sub-Licenses: This License is not assignable, and any attempt by
the Licensee to assign any portion of the License or to grant a sub-license, except as provided for
in this Agreement, shall be deemed a breach of this Agreement and shall be cause for
termination.
5. Validity and Ownership of Mark: The Licensee is prohibited from challenging or
contesting in any way the Licensor's ownership of the Mark with the U.S. Patent & Trademark
Page 2 of 17
-------
Office, or with any other trademark office, or the Licensor's exclusive worldwide ownership of the
Mark.
6. Use of Mark:
Licensee shall abide by the following guidelines:
(A) The Licensee acknowledges that the Licensor considers the mark to be its official
recognition mark, and holds it out to the public as such.
(B) The Licensee further agrees that the use of mark shall be done in such a way so that
there does not exist any appearance of Government endorsement, authorization or
affiliation of the Licensor with the Licensee, other than as such affiliation is specified
herein between Licensor and Licensee.
7. Infringement. The Licensee is required to notify the Licensor of any potential
infringement of the mark of which the Licensee is aware, or reasonably should be aware. The
Licensor retains the right to determine what constitutes infringement and the course of action
to be taken to address it.
The Licensee shall also notify the Licensor of any claims of which the Licensee is aware
that the licensed Mark is infringing the name, logo or trademark of another.
8. Governing Law. This Agreement shall be interpreted and implemented in accordance
with the laws applicable to the United States Government as interpreted by the U.S. District
Court for the District of Columbia.
9. Foreign Trademarks and Service Marks: Licensee agrees to provide all lawful
assistance, as reasonable and at Licensor's request and expense, to Licensor should Licensor
decide to register the mark in foreign countries. Licensee shall comply with all applicable legal
requirements governing trademark and service mark use, including but not limited to, registered
user requirements. Licensee agrees that all use of the mark by Licensee shall inure to the benefit
of the Licensor.
10. Indemnification: The Licensee agrees to indemnify and hold the Licensor harmless
from any and all claims, damages and attorneys' fees arising from the use of the Mark by the
Licensee and its operations under the Agreement, except to the extent that any such claims,
damages or attorneys' fees arose in connection with any act or failure to act by the Agency.
Although the Licensor is precluded from indemnifying the Licensee, per se, pursuant to the Anti-
Deficiency Act, the Licensor warrants that it is the owner of the Mark that is the subject of this
Agreement, and that it knows of no other entity with superior rights therein. Further, it agrees
to cooperate with and assist the Licensee in the unlikely event that the Licensee's use of the
Mark is challenged.
11. Prior Agreements: This Agreement sets forth and contains the entirety of
representations, understandings and agreements of the parties hereto and merges all prior
representations, understandings and agreements. This Agreement may be amended only
through a written instrument executed by a duly authorized representative of each of the Parties
hereto.
Page 3 of 17
-------
In witness whereof, the parties have caused this document to be duly executed as of the
latter of the two dates below.
For the United States Environmental Protection Agency
Joann Jackson Stephens Date
SmartWay Brand Manager
Fo r t h e
Insert Manufacturer Company Name
Insert Name
Insert Title
Insert company address
Insert company phone number
Insert email address
Insert Date
Please fax, mail or e-mail a signed copy of this document to:
Joann Jackson-Stephens
U.S. EPA-SmartWay
2565 Plymouth Road
Ann Arbor, Ml 48105
Phone: (734) 214-4767
Fax: (734) 214-4052
e-mail: jackson-stephens.joann(gepa.gov
Page 4 of 17
-------
Technical Specifications & Requirements
For Using the US EPA Designated SmartWay* Mark on
Qualifying Tractors and Trailers
These technical specifications for equipping a tractor or trailer to meet the voluntary
requirements for the US EPA Designated SmartWay mark are divided into two sections:
SmartWay Tractor Equipment list; and the SmartWay Trailer Equipment list.
SmartWay Tractor Equipment list
The tractors listed below are US EPA SmartWay tractors and meet the voluntary SmartWay
technical specifications for use of the US EPA Designated SmartWay mark when equipped in
accordance with the following tables (i.e., aerodynamics, engine, tires, and idle reduction). Current
high roof sleeper cab tractor models that qualify are:
Base Tractor
Manufacturer
Navistar
Navistar
Navistar
Mack
Daimler
Daimler
Daimler
Volvo
Volvo
Kenworth
Kenworth
Kenworth
Peterbilt
Peterbilt
Peterbilt
Peterbilt
Tractor Model
Prostar (and Prostar+) 2007
92001 2007
LoneStar 2008
Pinnacle 2008
Columbia 2008
Century Class S/T 2008
Cascadia 2008
VN 670 7630 2007
VN 780 2007
T2000 2008
T660 2008
T700 2011
387 2008
386 2008
384 2010
587 2011
Model Year
or newer
2008 & 2009
or newer
or newer
or newer
or newer
or newer
or newer
or newer
2009,2010,2011
or newer
or newer
2009,2010,2011
or newer
or newer
or newer
This tractor manufacturer list may be updated in the future.
Aerodynamics
A SmartWay-designated base aerodynamic tractor model is equipped with:
Integrated high roof sleeper cab
Aerodynamic mirrors
Aerodynamic bumper
Cab side extenders
Fuel tank fairings
Engine
Specifications
A 2007 or later model year engine certified to meet U.S. EPA NOx/PM emission
requirements.
Tractor Wheels
EPA encourages (but does not require) the use of lighter-weight aluminum wheels
rather than steel wheels, on the SmartWay tractor. Manufacturers include:
Alcoa aluminum wheels
Accuride aluminum wheels
Page 5 of 17
-------
Tractor Tire
Specifications
Low-rolling resistance steer and drive tires (duals or singles, aluminum wheels
optional) that provide at least a 3% vehicle (i.e., tractor and trailer) fuel economy
benefit, relative to mid-range rolling resistance tires as defined by EPA.
Approximately half the fuel savings, or about 1 percent, is contributed by the tractor
steer and drive tires. Qualifying trailer tire models from the SmartWay verified
technology list are included below. Recent updates to this list may be found at:
http://www.epa.gov/smartwav/transport/what-smartway/verified-
technologies.htmfftires
Current qualifying steer and drive tire models include:
Manufacturer Tire Type Product Name/ID Number
BF Goodrich Steer 4- ST244*
BF Goodrich Drive
Bridges-tone Steer 4-
Bridgestone Drive
Continental
Drive
R280, R287A (replaces R287),
Greatec SsooZ, M72O, Greatec
HDL ECO Plus, HDL2 ECO Plus, HDRl ECO Plus, HSR,
HSRl, HSRl ECO Plus, HSR2, HSR2 ECO Plus, HDR2 SA
HSL2 (replaces HSL), HSL2 ECO Plus, HSR, HSRl, HSRl
ECO Plus, HSR2, HSR2 ECO Plus, HDR2 SA
FR605
FD405
SP456 Fuel Max*
SP384Fuel Max*
RI109 Ecorun
BI887 Ecorun
FS507*
FD695PLUS
S371, S58O, S581
D660 ,S371,S580,S581
G305 Fuel Max AT*, G3O5 LHD Fuel Max, G392 SSD,
G572 Fuel Max
G399 Fuel Max, G662 Fuel Max*
GSL213FS
GT669+ FS
DLn,Z35A
ALO7+, ALn
KLS026
KLDOle
XDA Energy, XDA3, X-One XDA, Xone XDN2*, XOne
XDA Energy
XZA3*,XZA2,XZA-l+*, XZA2 Energy
RM180
S605
ST778SE
M657*
Ml 37
703ZL*, TY517ITIC2*, TY577
RY617,103ZR*,101ZL*
4-Tires that qualify for verification in the steer position also qualify for drive
tire verification.
* SmartWay verified tires that should operate as a "tire set". Confirm specific
steer/drive/trailer tire sets (should operate as a unit) with your tire
manufacturer/dealer.
Additional tire models may be added in the future.
Continental
Double Coin
Double Coin
Dunlop
Dunlop
Falken
Falken
Firestone
Firestone
General
General
Goodyear
Goodyear
GT Radial
GT Radial
Hankook
Hankook
Kumho
Kumho
Michelin
Michelin
Roadmaster (Cooper)
Saliun
Sumitomo
Toyo
Toyo
Yokohama
Yokohama
Steer 4
Steer 4
Drive
Drive
Steer 4
Steer 4
Drive
Steer 4
Drive
Steer4
Drive
Drive
Steer 4
Steer 4
Drive
Drive
Steer 4
Steer 4
Drive
Drive
Steer 4
Steer4
Steer 4
Steer 4
Drive
Steer 4
Drive
Steer 4
Page 6 of 17
-------
Effective March 6, 2011, verification is retired for several tire models which are
identified on the tire section of the SmartWay verified technology web site.
Idling Control Models must offer at least one option for turning off the main engine and providing
Readiness at least eight hours of idle-free auxiliary power, heat, and/or air conditioning. Each
system must have at least eight hours of operating capacity. Idle reduction
technologies include the following:
An auxiliary power unit or generator set
Fuel operated heater
Battery operated heating and/or cooling system
Thermal Storage System
Cur rent qualify ing id ling control equipment from the SmartWay verified technology
list may be found at: http://www.epa.gov/smartway/transport/what-
smartway/verified-technologies.htmffidle
SmartWay Trailer Equipment list
Trailers equipped as described in this section meet the voluntary SmartWay technical
specifications for use of the US EPA Designated SmartWay mark. A SmartWay Trailer
demonstrates 6.5% or greater reduction in fuel consumption, relative to a baseline 53 foot dry van
trailer. SmartWay Trailer fuel savings assume trailer is used with a fully-aerodynamic profile,
high-roof tractor with integrated roof design and side fairings. In this case, the aerodynamic
improvements can be 5% or greater fuel savings from reducing aerodynamic drag. The
SmartWay Designated trailer must meet the requirements for the base trailer and be equipped
with SmartWay verified tires and aerodynamics package listed below. The trailers may use one
of the following configurations:
Configuration A: Side skirt fairing; Front-mounted gap reducers; and Low-rolling
resistance tires
ConfigurationsB: Side skirt fairing; Rear-mounted tail fairing/ Boat tail; and Low-rolling
resistance tires
Optional Total Aero Configuration: Side skirt fairing; Front-mounted gap reducers; Rear-
mounted tail fairing/ Boat tail; and Low-rolling resistance tires
Configuration C. Advanced Trailer End Fairing1 (this can be used with or without other
fairings - estimated fuel savings 5%) and Low-rolling resistance tires
Configuration D: Advanced Trailer Skirt1 (this can be used with or without other fairings
- estimated fuel savings 5%); and Low-rolling resistance tires
NOTE: Aerodynamic Manufacturers must comply with all applicable DOT motor vehicle
standards.
Advanced trailer end fairings and skirts are advanced technologies that demonstrate greater fuel
savings than the standard equipment versions as a result of design changes made by the manufacturer to
improve the product.
Page 7 of 17
-------
ro
03
Design: A SmartWay Trailer is a new dry freight box van trailer for OTR use of 53 feet or
greater length. Additional trailer types may be added in the future.
An older (or pre-owned) dry van trailer of 53 feet or greater length may also qualify if
properly retrofitted
Dimensions:13' 5" to 13' 7" H, 53' L or greater, 102" outside W
Weight: Assumes a standard dry van trailer of approximately 13,000 pounds or less,
including weight of tires and wheels, but excluding weight of aerodynamic components
The following trailer manufacturers offers a qualifying model:
Great Dane Trailers
Hyundai Translead
Manac Inc.
Stoughton Trailers LLC
Strick Trailers, LLC
Trailmobile Corporation
Utility Trailer Manufacturing
Vanguard National Trailer Corporation
Wabash National Corporation
Wilson Trailer Company
Additional models may be added in the future.
Tire requirement: Demonstrate 1-1/2% (3% total SmartWay Tractor/Trailer) vehicle fuel
economy benefit, relative to mid-range rolling resistance tires as defined by EPA, by equipping
the trailer with low-rolling resistance trailer tires (duals or singles, aluminum wheels optional).
Qualifying trailer tire models from the SmartWay verified technology list are included below.
Any current updates may be found at:
http://www.epa.gov/smartwav/transport/what-smartway/verified-technologies.htmfftires
Manufacturer Tire Type Product Name/ Identification Number
c
o
u
14-
'u
01
Q.
in
-------
tu
01
EPA encourages (but does not require) the use of lighter-weight aluminum wheels rather than
c steel wheels, on the SmartWay trailer. For each 300 pounds reduced, 0.2% or greater fuel
+: savings are realized (or if weight-limited, payload capacity can be increased.)
^ a:
Alcoa aluminum wheels
Accuride aluminum wheels
T3
o
The aerodynamic requirements provide some flexibility t use one of the SmartWay
configurations (below) comprised of SmartWay verified aerodynamic devices. These
configurations demonstrate a benefit of at least 5% with the exception of the optional "Trailer
Aero" option which demonstrated 6%. SmartWay trailers must be equipped in one the following
aerodynamic configurations.
For new trailers, weight savings can be achieved by using aluminum, composite, and/or other light-
weight components in the trailer.
Page 9 of 17
-------
<
c
o
'+-
ro
i_
13
Low-rolling resistance tires: models
from manufacturers listed on page 9.
Trailer Side Skirt: manufacturers listed
on page 12.
Trailer Gap Reducer (fairing):
manufacturers listed on page 11.
Trailer Front-Mounted
j Gap Reducer/Fairing
firin
Trailer Side Skirt Fairing Lew Rolling Reassure Ties
CO
c
o
3
bo
o
u
Low-rolling resistance tires: models
from manufacturers listed on p. 9.
Trailer Side Skirt: manufacturers listed
on page 12.
Trailer Boat Tail: manufacturers listed
on page 11.
Trailer Rear Fairing
or Boat-tail
J
Trailer Side Skirt Fairing Low Rolling Resistance Ties
aluminum wfreefe {optional)
< c
1_ O
_u £
.-. ro
ro i-
<- 3
_
TO C
c o
_o u
+^
Q.
O
Low-rolling resistance tires: models from
manufacturers listed on p. 9.
Optional "Total Aero" Configuration:
Trailer Side Skirt: manufacturers
listed on page 12.
Trailer Gap Reducer (fairing):
manufacturers listed on page 11.
Trailer Boat Tail: manufacturers listed
on page 11.
Trailer Front-Mounted
[Gap Reducer/Fairing
Trailer Rear Fairin
or Boat-tail
VJ
/ / nrr
Trailer Side Shirt Fairing Low Rolling Resistance Tires
aluminum whetk (optional)
U
C
3
bn
o
U
Low-rolling resistance tires: models from
manufacturers listed on p. 9.
Advanced Trailer End Fairing: manufacturer
listed on page 13.
Advance Trailer
End Fatrirtg 1
OO1
Low Rolling Resistance Tires
ahimmjm wteets (optional)
C
O
3
bn
o
u
Low-rolling resistance tires: models from
manufacturers listed on p. 9.
Advanced Trailer Side Skirt: manufacturers
listed on page 14 (this equipment may be used
with or without other fairings).
\ħr
Advanced Trailer
Side Skirt fairing
Low Rollinrg Resistance Tr-es
G^umrrKJin wr^eefc/cpcionial?
Page 10 of 17
-------
Aero Equipment Type Verified Aerodynamic Trailer Technologies
Performance Specifications
When building the SmartWay trailer aerodynamic configuration,
use SmartWay verified devises listed below. Additional
aerodynamic technologies, manufacturers, and models may be
added in the future. Any current updates to the above SmartWay
verified aerodynamic equipment list may be found at:
http://www.epa.gov/smartwav/transport/what-smartway/verified-
technologies.htmffadvanced
Manufacturing an aerodynamic
trailer that meets or exceeds the
performance specifications:
Trailer Gap Reducer
Trailer Boat Tail
Manufacturer
Carrier Transicold
FreightWing
Laydon Composites
Nosecone
Manufacturer
AeroVolution
Aerodynamic Trailer
Systems (ATS)
Aerodynamic Trailer
Systems (ATS)
Transtex
Product Name
Gap Fairing
Gap Fairing
NoseFairing
Nose 3-D
Product Name
Inflatable Boat Tail
Dual lobe Boat Tail
SmartTaU
Transtex Composite
Rear Air Deflector
Model Name/Number
76-50172-00
76-50172-00
NoseFairing
NC-SWN3D48,NC-
SWN3D60, NC-SWN3DP
Model Name/Number
AeorVolution
Dual lobe Boat Tail
SmartTaU
Transtex Composite Rear
Air Deflector
For applications based upon testing,
provides at least a 1% fuel savings,
as demonstrated by an SAE J1321.
For applications based upon testing,
provides at least a 1% fuel savings,
as demonstrated by an SAE J1321.
Page 11 of 17
-------
Aero Equipment Type Verified Aerodynamic Trailer Technologies, continued
Manufacturer
Carrier Transicold
Fleet Engineers
FreightWing
Product Name Model Name/Number
Belly Fairing 76-5O169-O1
Extended Air Slipper
Belly Fairing 76-5O169-OO
Performance Specifications
For applications based upon testing,
provides at least a 4% fuel savings,
as demonstrated by an SAE J1321.
Laydon Composites 6 Panel system
Trailer Side Skirts
Laydon Composites 7 Panel System
Ridge Corp.
Silver Eagle
Silver Eagle
GreenWing
Mid-Length Skirt
Mini-Skirt
Cray Panel: TRSKeoooo-
001100 & Extensions:
TRSKeoooi-oooioo; White
Panel: TRSKeooio-oonoo &
Extensions: TRSK60011-
oooioo
Cray Panel: TRSK70000-
000100 & Extensions:
TRSK70001-000100 or
TRSK70001-H0100;
White ft)rte/:TRSK70010-
000100 & Extensions:
TRSK700H-000100 or
TRSK700H-H0100;
RACoooo2
MLSs
Transtex
Utility Trailer
Utility Side Skirt
120
Page 12 of 17
-------
Aero Equipment Type Verified Aerodynamic Trailer Technologies, continued Performance Specifications
Manufacturer
ATDynamics
Product Name
ATDynamic
TrailerTails
Model Name/Number
Model #08-1
For applications based upon testing,
provides at least a 5% fuel savings,
as demonstrated by an SAE J1321.
Advanced Trailer End
Fairing
ATS Integrated
Automated System
WindTamer with
SmartTail
WindTamer with
SmartTail
Smart Truck
UT-6 integrated
system
Page 13 of 17
-------
Aero Equipment Type Verified Aerodynamic Trailer Technologies, continued Performance Specifications
Advanced Trailer Side Skirt
Manufacturer
Aerofficient
Airflow Deflector
ATDynamics
Atlantic Great Dane
Carrier Transicold
FreightWing
Laydon Composites
Product Name
Fixed Side Fairing
Deflector
ATDynamics -
Transtex
Trailer Side Skirts
Aero Guard side skirt
Aeroflex Fairing
Aeroflex Belly
Fairing
7 Panel system
Laydon Composites 8 Panel system
Model Name/Number
FFGW;FFTI andASFS
Deflector
4OT-1
AGD400-43
76-50188-04; 76-5O188-2O;
76-5O188-21; 76-5O188-22;
and 76-50188-23
76-5O188-O3
TRSK700SA
Cray Panel: TRSKsoooo-
oooioo & Extension:
TRSKsoooi-noioo; White
/>
-------
Original equipment manufacturers (OEMs) may request to have their aerodynamic device, tire, or
idle reduction technology verified by SmartWay. Prior to conducting any testing for purposes of
SmartWay verification the OEM must contact SmartWay (s m a rtwav-tech (gepa.gov) to ensure
that the test plan is in accordance with applicable SAE and SmartWay-specif ic test protocols.
Approval of the test plan does not confer verification of the product as each product will be
evaluated by SmartWay staff for compliance with test protocols, policies, and verification
criteria and targets.
fur \\iire_\r\forrnatior\_
Visit: www.epa.gov/smartway for additional information about SmartWav.
ğ Visit: www.epa.gov/smartwav/transport/what-smartwav/tractor-trailer-manufacturers.htm for
additional information on SmartWay designated tractor/ trailers.
Visit www.epa.gov/smartwav/transport/what-smartwav/verified-technologies.htm for
additional information about the SmartWay technology verification.
Page 15 of 17
-------
ilc ...... Standards ...... ....... Logo ....... Usags ..... GyMMio.es
U.S. EPA Designated SmartWay" Mark
for Qualifying Tractors and Trailers
Promoting the Mark
The US EPA Designated SmartWay mark may be used in point-of-sale advertising (for on-site
locations and web sites) and promotional material (e.g. print advertising) of original equipment
manufacturers (OEM) of SmartWay qualified tractors and trailers. Media and other interested
parties may also use the SmartWay mark for articles or other educational purposes. However, the
mark may only be used in association with tractors and trailers that have met the SmartWay
technical specifications.
Only manufacturers of heavy-duty tractors and trailers may use the SmartWay mark. Component
manufacturers (such as tire or aerodynamic add-on manufacturers) may not apply the US EPA
Designated SmartWay mark to their products, product packaging, on their sales web sites or in their
point-of-sale advertising.
The US EPA Designated SmartWay mark may also be applied, by the original equipment
manufacturer (OEM), to the interior of a qualified SmartWay tractor or a SmartWay trailer. However,
it may not be applied to the windows of a tractor or in any place on a tractor's interior that is visible
from the exterior.
Correct Incorrect
Point of sale advertising (signs, banners) Cab window
Cab door interior Cab rear-view mirror
Cab dash Cab windshield
OEM sales web site
The following communication guidelines will prevent misrepresentation and consumer confusion.
Correct Incorrect
"Earned" "Endorse"
"Qualified" "Endorsed"
"Meets SmartWay specifications" "Rating"
"U.S. EPA Designated SmartWay" "Rated"
"SmartWay designated mark or logo" "Certified"
EPA recommends using words in the "correct" column to describe tractors and trailers which meet
the voluntary requirements for application of the SmartWay logo by OEMs. Text used in advertising,
articles, brochures, publications, annual reports, web sites, or any other promotional material must
never imply EPA endorsement of either the manufacturing company or sponsoring organization.
Page 16 of 17
-------
Graphics
The US EPA Designated SmartWay mark must be used its entirety and as shown. The only approved
logo files to be used can be obtained by contacting EPA. No other graphical representation of the
mark may be used.
The graphic may not be altered, cut apart, separated, or otherwise distorted in perspective or
appearance. The aspect ratio (length and width dimensions) must remain proportional. The logo
must never be reproduced smaller than 1.25" wide to ensure legibility.
Licensees, SmartWay Partners and other organizations are responsible for their own use of the US
EPA Designated SmartWay mark, as well as use by their representatives, such as ad agencies and
public relations firms.
Color Specifications
i. Spot Color - For spot color usage (often referred to as PMS or Pantone Matching System):
Prescribed green = 347
Prescribed blue = 3005
2. Four-Color Process - For four-color process printing, the build formulas detailed here for
the prescribed green and blue must be used.
Four-Color Process Four-Color Process
C 100% C 100%
M o% M 40%
Y 85% Y o%
K 5% K o%
3. Black and White Version - The graphics in their entirety may also be reproduced in 100%
black.
Page 17 of 17
------- |