United States
Environmental Protection
Agency
Office of Air Quality
Planning and Standards
Research Triangle Park, NC 27711
EPA 456/B-01-001B
June 2001
«s»EPA USER'S MANUAL FOR THE
RACT/BACT/LAER CLEARINGHOUSE
(RBLC) WEB
Volume 2 - Data Entry
lithlhlln bact
GOVERNMENT
RBLC
CLEAN AIR
Clearinghouse
'I
Developed as Part of a Joint Effort Between the
U.S. Environmental Protection Agency's
Clean Air Technology Center (CATC) and
State and Local Air Pollution Control Agencies

-------
USER S MANUAL FOR THE
RACT/BACT/LAER CLEARINGHOUSE (RBLC) WEB
CLEAN AIR TECHNOLOGY CENTER
SPONSORED BY:
Information Transfer Group
Office of Air Quality Planning and Standards
U.S. Environmental Protection Agency
Research Triangle Park, North Carolina 27711
Date: July 2001

-------
DISCLAIMER
This report has been reviewed by the Information Transfer and Program Integration
Division of the Office of Air Quality Planning and Standards, U.S. Environmental Protection
Agency and approved for publication. Approval does not signify that the contents reflect the
views and policies of the U.S. Environmental Protection Agency. Mention of trade names or
commercial products is not intended to constitute endorsement or recommendation for use.
Copies of this report are available from the National Technical Information Service, 5285 Port
Royal Road, Springfield, Virginia 22161, telephone (800) 553-6847.

-------
PREFACE
This user's manual was prepared for and funded by the New Source Review
RACT/BACT/LAER Clearinghouse (RBLC),1 U.S. Environmental Protection Agency (EPA). The
RBLC has been established and is maintained by the Clean Air Technology Center (CATC) to assist
State and local air pollution control personnel in making control technology determinations and in
sharing technology information.
The RBLC provides data on prevention and control technology determinations made primarily
by State and local permitting agencies. The Clearinghouse contains over 4,000 determinations that can
help the user to identify appropriate technologies to mitigate or treat most air pollutant emission streams.
The RBLC was designed to help permit applicants and reviewers make pollution prevention and
control technology decisions for stationary air pollution sources and includes data submitted by 50
states and territories in the U.S. on over 200 different air pollutants and 1,000 industrial processes.
The Clearinghouse also has a rule data base that summarizes all emission standards issued by
EPA's Office of Air Quality Planning and Standards (OAQPS). This includes New Source
Performance Standards (NSPS), National Emission Standards for Hazardous Air Pollutants
(NESHAP), and Maximum Achievable Control Technology (MACT) standards. The rule data base
also includes prevention and control technology cost information related to each rule and references to
supporting documentation.
Read the section, Quick Start Instructions for the RBLC Data Base, in this document to
begin using the RBLC Web.
1 NOTE: RACT, BACT and LAER are acronyms for different Clean Air Act program requirements
combined to create the name "RACT/BACT/ LAER Clearinghouse." RACT, or Reasonably Available
Control Technology, is required on existing sources in areas that are not meeting national ambient air
quality standards (i.e., non-attainment areas). BACT, or Best Available Control Technology, is
required on major new or modified sources in "clean" areas (i.e., attainment areas). LAER, or Lowest
Achievable Emission Rate, is required on major new or modified sources in non-attainment areas.
However, data in the Clearinghouse is not limited just to sources subject to these requirements.
Noteworthy prevention and control technology decisions are included in the RBLC even if they are not
related to RACT, BACT, or LAER decisions.
in

-------
TABLE OF CONTENTS
VOLUME I: RBLC BASICS
VOLUME IE: RBLC DATA ENTRY
Disclaimer	ii
Preface	iii
Section 4 - Data Entry Overview
4.1	Access	4-1
4.2	On-Line Help Options	4-1
4.3	Navigating Data Entry	4-1
4.4	Planning and Preparation	4-2
4.5	Data Fields and Formats	4-4
Section 5 - RBLC Web Permit Data Entry and Editing Procedures	5-1
5.1	Add a New Determination	5-1
5.2	Edit In-Process Determination	5-2
5.3	Edit Completed Determination	5-4
5.4	Paper (Hardcopy) Data Submission	5-4
5.5	Standalone Editor — The Standalone Editor will be available in the summer of2001 5-4
VOLUME HI: APPENDICES
Appendix A — Data Submittal Form and Instructions	A-1
Appendix B — Agency Code Listing	B -1
Appendix C — Process Type Code Listing	C -1
Appendix D — Abbreviations for Processes, Units, and Pollutants	D -1
Abbreviations for Processes and Descriptors
Abbreviations for Emission Limit Units
Abbreviations for Pollutants
Appendix E - RBLC Standard Emission Limit Units by Process Type Code	E-1
iv

-------
Appendix F — Examples of RBLC Standard Reports
F-l
Index of Control Technology Determinations (formerly Appendix F)
Control Technology Determinations by Process Type Code (formerly Appendix G)
Detailed Source Listing (formerly Appendix H)
Freeform Data
ASCH Delimited Data Format
Appendix G — Examples of Federal/State Regulation Standard Reports	G-1
Detailed Listing by Identifier (formerly Appendix H)
Freeform Data
v

-------
TABLES AND FIGURES
Page
Table 4.1 Names and Characteristics of RBLC Data Fields	4-5
Figure 4.1 QA/QC Checklist	4-11
vi

-------
SECTION 4:
DATA ENTRY OVERVIEW
4.1	Access
Online editing of the RBLC permit database is available to authorized users from State and
local agencies across the United States. Contact the RBLC Webmaster to request authorization to add
and update information.2 Authorized users can add and edit determinations and contact information for
their agency and state.
New determinations are entered first into the Transient/Early Notification data base and move
through the following stages: In Process, Ready for Quality Assurance (QA), then QA Complete. EPA
promotes determinations to the current RBLC data base. Authorized users can edit completed
determinations by copying the determination into the Transient/Early Notification data base. The
determination will take the same route through QA and EPA review before promotion into the current
data base. Please note that the original (promoted) determination will remain available until the revised
determination is promoted. The revised determination will then replace the original entry. Once the
revised determination has been promoted, the old version of the same determination will no longer be
available.
4.2	On-Line Help Options
Like other portions of the RBLC Web, the on-line HELP reference is available for data fields
throughout the system (see Section 1.2.2 in Volume I of this User's Manual for more information). The
entire HELP system, with a table of contents, is available by clicking the RBLC Help link at the bottom
of each data entry page. Future additions to the system will include an on-line context sensitive HELP
function for data entry fields throughout the system. When installed, this function will allow the user to
click on the Help icon nearest to the data entry field in question to access a HELP file for that field.
4.3	Navigating Data Entry
Within the data entry portion of the RBLC Web site, users can choose from the following
options:
•	Add New Determination: create a new data base entry to the transient data base.
•	Edit In-Process Determination: edit an existing transient database entry.
2 The RBLC Webmaster is Joe Steigerwald, email: Steigerwald.Joe@epamail.epa.gov: Telephone:
(919) 541-2736. See also Volume I, Section 1.1.4 of this User's Manual.
4-1

-------
•	Edit Completed Determination: move a determination from the current data base to the
transient data base for editing (using the Edit In-Process Determination option).
•	Add/Edit Contact Information: add or edit agency contact information.
•	Exit Data Entry: log out from the data entry system.
Please note: each data entry screen must be saved using either the save and exit, save and
continue, or update buttons. Using the web browser buttons to move forward or back will not
save the data that has been entered.
The RBLC data entry page includes a logout button (Exit Data Entry). For security reasons,
users should log out after every data entry session. The system will prompt the user to log in again if a
session is inactive for longer than 20 minutes. Clicking the OK button at the prompt will allow the user
to log in and continue with the session. Data entered previously can then be saved. Clicking the
Cancel button at the prompt, however, will return the user to the initial data entry log in screen. Data
entered previously will not be saved. Although previously accessed data entry screens can be viewed
after logging off by using the web browser Back button, the system will not save data entered without
an authorized log in.
Adding and editing determinations is done using on-line forms. Buttons at the top and bottom
of each form allow the user to navigate, save, and update data. Many of the data fields use drop-down
lists that facilitate entry of correctly formatted entries.
4.4 Planning and Preparation
Agencies may wish to define procedures and quality standards for entry of determination data
to the RBLC, as incomplete or incorrect data can result in repeated calls to the agency for more
information, misunderstandings about the data with industries or the public, and other inefficient uses of
staff time and effort. In some cases, appointing one person to coordinate a large data entry effort and
to be the EPA contact point may be a logical approach. In other cases, defining specific procedures
and tracking the progress of entries may be more than adequate. In all cases, quality assurance and
quality control (QA/QC) standards should be maintained. See Section 4.5 for a suggested QA/QC
checklist.
Data entry and edits can be done most efficiently when the RBLC web data requirements and
data fields are understood and permit information has been organized before beginning entry. It is
recommended that permit information be organized before entry, so that all of the required information
(e.g., codes, units, and abbreviations) will be on hand during data entry.
Refer to Section 4.5 of this document for:
• Descriptions of data fields;
4-2

-------
•	Required data fields, units, and formats; and
•	Data organization tips.
Keep in mind that permit information needs to be entered in such a way that the data base
search routines will be able to find it when it is relevant. Take the time to accurately match RBLC
process type codes and Source Classification Codes (SCCs) to the processes, and to describe control
devices or pollution prevention technology. The RBLC Documents page, accessed from the RBLC
Web Main page, contains text and data base files containing the Source Industrial Classification (SIC)
Codes and the SCCs needed to accurately categorize facilities and processes.3 Identify processes
and pollutants for which standard emission limits are required (see Appendix E for a list).
At a more general level, identify the information needed to enter a complete determination. A
determination must have information at the facility, process, and pollutant levels. Identify all likely
pollutants for a process and be prepared to address them all, either as pollutant entries or explanatory
notes in the process entry. Identify situations where a single process or piece of equipment may need
to be entered as multiple process entries or several processes may need to be combined (see the
examples below). When questions arise about how to enter non-standard situations, please contact the
RBLC Webmaster.
Example - One process, many emission limits
Problem: Separate emission limits for NOx emissions have been set for multiple operation
scenarios for turbines at a power plant. There are six operation scenarios based on three different
fuel options and whether the turbines operate as simple or combined cycle. Emission limits for other
pollutants are the same regardless of the scenario.
Solution: Enter the scenarios as six separate processes (process type codes and SCCs change for
each scenario), and enter the NOx emissions limits for each. Create a seventh process for the
generic process (mixed fuels, and simple or combined cycles undefined), and enter the remaining
pollutant limits under the seventh process. Document and explain this approach in the facility and
process notes.
3 The U.S Census Bureau maintains a Web site which cross references SIC codes with the North
American Industry Classification System (NAICS) of industrial codes:
http://www.census.gov/epcd/www/naics.html The EPA's Emission Factor and Inventory Group
maintains the list of SCCs and any updates of those codes can be found at:
http://www.epa.gov/ttn/chief/codes/index.html.
4-3

-------
Example - Many identical processes , one set of emission limits
Problem: Eight identical natural gas fueled turbines, vented through a single stack, are permitted
together with identical emission limits. Emission limits are expressed in units of pounds per hour for
each turbine, and parts per million exiting from the stack. How should the turbines' emission limits
be entered in the RBLC?
Solution: Enter all eight turbines as a single process. Specify in the process notes the number of
turbines and whether the throughput is the combined throughput or throughput for each turbine.
Enter the emission limits, remembering to enter the parts per million emission limit in the standard
emission limit fields. Specify in the notes field that the pounds per hour emission limit is for each
4.5 Data Fields and Formats
For a determination to be considered complete and eligible for promotion to the permanent
RBLC data base, certain data fields must be entered, and required data formats must be observed.
Data for most of the searchable fields must be entered before a screen can be saved. In the on-line
data entry forms, the required fields are marked with a diamond (~).
Use Table 4.1 to identify required and recommended data fields. These requirements help
insure that searches will be productive and that the data base contains information that is helpful to most
users. Data elements marked as recommended fields are those that may be required under future NSR
regulations. Collecting and entering these data will improve the quality and usefulness of the data base.
Refer to Appendix A and the on-line documentation for instructions for entries to each data
field. As discussed previously, planning and organizing the data beforehand will make the data entry
process more efficient. Figure 4-1 is a suggested QA/QC checklist for entries.
After a determination has been entered into the system, EPA will review the entry, follow up
with the agency if necessary, and then promote the completed entry to the permanent RBLC data base.
4-4

-------
TABLE 4.1
NAMES AND CHARACTERISTICS OF RBLC DATA FIELDS
FIELD NAME
REQUIRED;
RECOMMENDED;
OR NOT
REQUIRED
USED FOR
QUERIES
NOTES
FACILITY LEVEL INFORMATION
RBLC ID
Required
Y
Assigned by the system. Unique to each determination.
Plant/Company name
Required
Y
Name of the facility, include the name of the company that
owns the facility, if is different.
Plant contact name
Recommended
N

Plant contact's street address
Recommended
N
Plant Contact's mailing address, may not be facility
address. Zip codes can be found at:
http://www.usps.gov/ncsc/lookxips/lookups.htm.
Plant contact's city, state and
zip code
Recommended
N
Plant contact's telephone/fax
Recommended
N

Plant contact's email address
Recommended
N

Plant location - UTM
coordinates
Recommended
N
Actual plant location
Plant location - County
Not required
N

Plant location - State
Required
Y
Assigned by the system.
EPA Region
Required
Y
Assigned by the system.
Agency Code and Name
Required
Y
Choose from a drop-down list.
4-5

-------
FIELD NAME
REQUIRED;
RECOMMENDED;
OR NOT
REQUIRED
USED FOR
QUERIES
NOTES
Agency Contact and Telephone
Number
Required
N
Choose from a drop-down list.
Public Hearing
Not Required
N

New/Modified Source
Required
N

Permit Number
Required
Y

AIRS Facility Number
(universal Plant ID)
Recommended
Y

SIC Code
Required
Y
Drop down list; complete list in RBLC Documents section.
Application Received
Recommended
N

Permit Issue Date
Required
Y
Must be actual date in order for the determination to be
promoted to the current data base.
Start-up Date
Recommended
N

Compliance Verification Date
Recommended
N

Facility Notes
Recommended
N
Notes allow the entry of non-standard information.
Affected Class 1 Areas
Recommended
Y

Plant Narrative/Emission
Sources/Fuel/Abatement
Description
Recommended
N

4-6

-------
FIELD NAME
REQUIRED;
RECOMMENDED;
OR NOT
REQUIRED
USED FOR
QUERIES
NOTES
Plantwide Emissions
Recommended
Y

PROCESS LEVEL INFORMATION
Process Description
Required
Y

Process Type
Required
Y
Includes process type code, selected from a drop-down
list. Also listed in Appendix D of this User's Manual.
Source Category Code (SCC)
Required
Y
A listing of SCCs can be found on the RLBC Documents
page.
Primary Fuel
Recommended
N
For combustion units only
Throughput Capacity and Units
Not Required
N
If this information is CBI, it should not be entered.
Compliance Verification
Recommended
N

Process Notes
Recommended
N

POLLUTANT LEVEL INFORMATION
Pollutant Name/Chemical
Abstract Service (CAS)
Number
Required
Y
Select pollutant name and CAS number from the drop-
down list.
Control Method Code
Required
Y

Control Method Description
Required*
Y
* A control method description is not required when there
are no controls (control method code = N)
4-7

-------
FIELD NAME
REQUIRED;
RECOMMENDED;
OR NOT
REQUIRED
USED FOR
QUERIES
NOTES
Number of Control Options
Considered
Not Required
N

Rank of Option Selected
Not Required
N

Primary Emission Limit
Required*
Y
*An emission limit is required for every pollutant entry.
Three exceptions are allowed, although it is still
recommended that you provide a primary emission limit.
The exceptions are:
1)	If no control is used, (control method code = N);
2)	If a standardized emission limit is listed; or
3)	If percent efficiency is substituted as a limit as part of
the permit.
Primary Emission Limit Unit
Required
Y
An emission unit is required if a limit has been entered.
Alternate Emission Limit
Not Required
N

Alternate Emission Limit Unit
Not Required
N
An emission unit is required if a limit has been entered.
Standardized Emission Limit
Required*
Y
* For all processes, the emission limit for visible emissions
(VE as percent opacity) should be listed in the
standardized emission limit field.
A standardized emission limit is required for the pollutants
listed under the process type codes in Appendix E, RBLC
Standard Emission Units by Process Type Code. If the
process type and pollutant is not listed in Appendix E, an
emission limit is not required.
4-8

-------
FIELD NAME
REQUIRED;
RECOMMENDED;
OR NOT
REQUIRED
USED FOR
QUERIES
NOTES
Standardized Emission Limit
Unit
Required
Y
An emission unit is required if a limit has been entered.
Emission Limit Basis
Required
Y

% Efficiency
Recommended
N
See note on primary emission limits above.
Emission Type
Required
Y
Options are: P (point), A (area), and F (fugitive).
Costs Verified by Agency
Recommended
N

Capital Cost of Control
Equipment
Not Required
N
If this information is CBI, it should not be entered.
O/M Cost of Control
Equipment
Not Required
N
If this information is CBI, it should not be entered.
Year Used in Cost Estimates
Recommended
N
If this information is CBI, it should not be entered.
Annualized Cost
Not Required
N
In dollars
Cost Effectiveness
Recommended
N
In dollars per ton
Incremental Cost Effectiveness
Recommended


4-9

-------
QA/QC Checklist for Data Entry and Editing
For the Entire Determination
•	Keep in mind the general goals of a QA review: insuring entry completeness,
accuracy in data entry, coding, naming, and reasonableness.
•	Throughout the determination entry, check for typographical errors and misspellings,
even in the notes fields. Make sure that the notes are concise, well worded, and
informative.
•	Check for accuracy in data entry.
•	Check all required and recommended data fields. Use Table 4.1 and Appendix A
to identify those fields.
Facility Level Input Form
1)	Are name, address and location data reasonable and correct? Include any entries for UTM
coordinates in the checks. UTM coordinates are defined as zone, easting and northing (x and y
coordinates, respectively). The conterminous 48 States are covered by 10 zones, from Zone 10 on
the west coast through Zone 19 in New England. Alaska is covered by zones 10 through 2, and
Hawaii by zones 4 and 5.
2)	Check SIC codes. If you were looking for information about this type of facility, would you
search using the code that has been assigned?
3)	Is the permit issued date an actual or estimated date? It will need to be actual for the
determination to be promoted. Is the permit issued date after the application received date? Actual
start up and compliance dates are especially helpful to users of the data base because those dates
indicate that the project is actually operating. These should be entered if they are available.
Process Level Input Form
4)	Are all of the processes covered by the determination included? Are the processes defined so
that pollutants, controls and limits can be entered in an understandable way for each one?
5)	Check the process name. Does it use the standard naming approach for processes described in
the data entry instructions in Appendix A, RBLC Data Submittal Form and Instructions (e.g.,
turbine, single cycle, natural gas)?
Figure 4-1: QA/QC Checklist
4-10

-------
6)	Check the SCC designations. If you were looking for this process, would you search using the
code that you assigned?
7)	Check the units for throughput. Use Appendix D to check units abbreviations.
8)	If throughput is not in terms of fuel, is information provided about the throughput material in the
notes?
9)	Has compliance information been entered? If compliance has been verified using "other"
methods, have these methods been specified under "describe other"9
Pollutant Level Input Form
10)	Are all of the pollutants included for each process? In many cases, the permit addresses only
one or a few of the pollutants that can be expected to be emitted from a process. If there are
pollutants that are not included in the determination for a process, include an explanation in the
process notes.
11)	Is the Control Method Code properly assigned? Remember that a device added to a process
that reduces emissions during the process (e.g., low-NOx burners) should be defined as pollution
prevention, not as an add-on. Pollution prevention encompasses recycling, materials changes and
reformulation, and pollution reduction technology that is integral to the process.
12)	If the control method code is add on, pollution prevention or both (add on and pollution
prevention), there must be a description of the control method in the text field.
13)	Check the descriptors for add on control devices and pollution prevention methods. Use the
names and abbreviations in Appendix D, RBLC Process, Unit, and Pollutant Abbreviations to
insure that consistent terms are used throughout the data base.
14)	Have emission limits been entered? Limits can be entered as either emissions or as a control's
percent efficiency. If the only limit is the percent efficiency, the efficiency should be entered in the
primary emission limit field and in the percent efficiency field.
15)	Are pollutant emission limits, and percent efficiency levels reasonable?
Figure 4.1: QA/QC Checklist, continued.
4-11

-------
16)	Check units for primary and alternate emission limits. Use Appendix D to check abbreviations
for emission units.
17)	Emission limits for visible emissions (VE) should be expressed as percent opacity (% opacity).
VE emission limits for all processes should be entered in the standard emission limit field.
18)	Check the processes in the determination against the list of processes included in Appendix E,
RBLC Standard Emission Units by Process Type Code. If a process matches any of those on
that list, there should be a standard emission limit entered for the pollutants listed for that process.
Figure 4.1: QA/QC Checklist, continued.
4-12

-------
SECTION 5
RBLC WEB PERMIT DATA ENTRY AND EDITING PROCEDURES
Access and authorization to enter and edit data in the RBLC Web is discussed in Section 4.1 of
this volume. Navigation while using the data entry and editing options on the RBLC Web is described
in Section 4.3. The following sections describe the procedures available to enter and edit
determinations on the RBLC Web and to submit data on paper forms or as computer files. The section
titles for RBLC Web functions are same as the Data Entry Menu Web buttons that they describe.
When using the RBLC Web data entry and editing procedures, new determinations are entered
first into the Transient/Early Notification data base and move through the following stages: In Process,
Ready for Quality Assurance (QA), then QA Complete. Flags to mark the determination's status are
available on a pull-down list at the top of the facility edit page, and are discussed in more detail in
Section 5.2 of this volume. EPA promotes determinations to the current RBLC data base.
5.1 Add a New Determination
The Add a New Determination button on the Data Entry Menu is for creating a new
determination listing in the RBLC data base. When a user has multiple-state data entry privileges, the
first screen of this sequence will ask the user to identify the state where the determination is located. If
a user has single-state data entry privileges, the first screen will be the facility level entry form. The
system will assign a facility number (an internal tracking number) and an RBLC ID. See Section 2.2 of
this User's Manual for more information about RBLC IDs.
The Add a New Determination option will guide the user through each level of data that should
be entered (i.e., facility, process, and pollutant) using the Save and Continue button at the bottom of
each entry form. The data entry forms and navigation buttons available are:
•	Facility form
S Main Menu/Abort Changes - Prompts user to return and save data entered,
then will return to the main permit data entry and editing page. Using the Main
Menu button without saving the newly entered data will result in the data being
lost.
S Save & Exit - Saves the data in the form, exits from the Add option.
S Save & Continue - Saves the data in the form, continues to the Process form.
•	Process form
S Main Menu/Abort Changes - Prompts user to return and save data entered,
then will return to the main permit data entry and editing page. Using the Main
Menu button without saving the newly entered data will result in the data being
lost.
5-1

-------
S Add another - Displays a blank process entry form to add a new process.
S Save & Exit - Saves the data in the form, returns the user to the main permit
data entry and editing page.
S Save & Continue - Saves the data in the form, continues to the Pollutant form.
• Pollutant form
S Main Menu/Abort Changes - Prompts user to return and save data entered,
then will return to the main permit data entry and editing page. Using the Main
Menu button without saving the newly entered data will result in the data being
lost.
S Save & Add another - Saves the data in the form, and displays a blank
pollutant entry form to add a new pollutant.
S Save & Main Menu - Saves the data in the form, returns the user to the main
permit data entry and editing page.
S New Process - Does not save the data in the pollutant form, continues to a
new process form.
Some data fields will be marked with a diamond icon:
~
These fields are mandatory and must be filled out in order for the page to be saved. Please
note that additional fields are required for promotion of the determination, and are discussed in Section
4.5 of this volume.
Facility-wide emissions can be entered on this form. It is recommended that the form be saved
before entering this portion of the data.
The Edit In-Process Determination option (discussed in the section below) may provide more
flexibility when entering information for a new determination by allowing the user to move to any screen
in the determination entry. In that case, enter the new determination's facility data while using the Add
a New Determination module, then press the Save and Exit button. Then use the Edit In-Process
Determination option to enter process and pollutant data.
5.2 Edit In-Process Determination
The second button on the main RBLC Data Entry Page is labeled Edit In-Process
Determination. This allows edits to determinations in the transient data base. The entry forms for
facility, process, and pollutant level data are the same as those in the Add a New Determination option,
with three exceptions: a pull-down menu for the choice of entry status on the facility form, a button
allowing the user to mark determinations available to the public or not, and the wider range of choices
5-2

-------
for navigation buttons. A selection must be made from the entry status menu before changes to the
facility level data can be saved. Entry status menu selections are: In Process; Ready for QA; and QA
Complete. Agencies entering data should mark their incomplete and in progress entries as being In
Process. Once an agency has completed their own QA, and are ready to send the completed
determination entry to the EPA, the entry should be marked Ready for QA. The QA Complete flag is
used by EPA's contractors and EPA to designate determinations ready for promotion.
The data entry forms and navigation buttons available are:
Facility form
S Main Menu/Abort Changes - Prompts user to return and save data entered,
then will return to the main permit data entry and editing page. Using the Main
Menu button without saving the newly entered data will result in the data being
lost.
S Save/Update - Saves and updates the data in the form.
S Process List - Displays the process selection form.
S Make [RBLC facility ID] Non-Viewable/Publically Viewable - Allows data to
remain private until released for public view.
Process selection form
S Main Menu - Returns the user to the main permit data entry and editing page.
S Edit Facility - Returns the user to the facility form.
S Process selection drop-down list - Lists all processes entered for this
determination.
S Edit Process - Displays the process selected.
S Pollutant List - Displays a pollutant selection form for the process' pollutants.
Process form (Only the Save/Update button saves entered data):
S Main Menu/Abort changes - Prompts user to return and save data entered,
then will return to the main permit data entry and editing page.
S Add Another - Displays another blank process form.
S Save/Update - Saves and updates the data in the form.
S Process List- Displays the process selection form.
S Pollutant List - Displays the process' pollutant selection form.
S Facility Information - Returns the user to the facility page.
Pollutant selection form
S Main Menu/Abort changes - Prompts user to return and save data entered,
then will return to the main permit data entry and editing page.
S Process List - Displays the process selection form.
S Edit Facility - Returns the user to the facility form.
5-3

-------
S Pollutant selection drop-down list - Lists all pollutants entered for the currently
selected process.
• Pollutant form (Only the Save/Update button saves entered data):
S Main Menu - Return the user to the main permit data entry and editing page.
S Add Another - Displays another blank pollutant form.
S Update/Save - Saves and updates the data in the form.
S Pollutant List - Displays the pollutant selection form.
S Process List - Displays the process selection form.
S Edit Facility - Returns the user to the facility page.
The Edit option allows for more flexibility in moving from screen to screen than when using the
Add New Determination option. New processes, and pollutant entries can be made using the Edit
option, but a new entry must be entered using the New Determination option.
5.3	Edit Completed Determination
There are cases when a determination needs to be re-edited after it has been through QA and
promotion to the RBLC current data base. The third option on the main RBLC Data Entry page allows
a user to select a determination from the current data base and transfer it to the transient data base for
editing. In this option, the determination is selected using the same type of pull-down menu that is used
in the Edit In-Process Determination option. Once a determination is selected, the facility level
information is displayed, and then the determination is transferred to the transient data base by pressing
the Edit button. The Edit In-Process Determination option is used to edit these determinations. The
determination will take the same route through QA and EPA review before promotion into the current
data base. Please note that the old (promoted) determination will remain available until the revised
determination has been promoted. Once the revised determination has been promoted, the old version
of the same determination will no longer be available.
5.4	Paper (Hardcopy) Data Submission
EPA guidance for submitting determinations using the paper form is in Appendix F. Included is
the most recent version of the paper form. In addition to the guidance provided in Appendix F, review
the data fields and formats discussion in Section 4.5.
5.5	Standalone Editor
— The Standalone Editor will be available in the summer of 2001.—
5-4

-------
APPENDIX A
DATA SUBMITTAL FORM

-------
This page has been intentionally left blank.

-------
Mail to: RACT/BACT/LAER CLEARINGHOUSE	^ . A ™ a
RHI.C (MI)-l2)	RACT/BACT/LAER CLEARINGHOUSE Date Submitted.
US EPA	INPUT FORM
RTP, NC 27711
Company/Plant Name: ¦
Plant/Facility Contact Information:

Mailing Address:






Plant Contact Name:




Telephone Number:
Fax:



E-Mail Address:

Cilv
State:
Zip Code:

Physical Plant Location Information: UTM Coordinates: X:,
Public Hearing Held? Y N (circle one)
Y:
Zone:
The Source is: New Modified (circle one)
Permit Number:	
AIRS Facility Number:
EPA ID Number:	
SIC Code:	
Scheduling Information:
Received Application:
Final Permit Issued:
Start Up Operation:
Compliance Verification:
Date (circle one)


/ / Estimated/Actual
Company/Plant Location:
/ / Fstimntprl/Artiinl
State
/ / Ft:timf|tPd/Af,tual
Countv
/ / Estimated/Actual

Permitting Agency Contact Information:
Permitting Agency:	
Agency Contact:	
Telephone Number:	
E-Mail Address:
Address:.
Fax:
Countv:
State:
Zip Code:,
Class One Area Name
Class One Areas Affected within 250km of source:
Distance (km)	Class One Area Name
Distance (km)
NSR/RBLC Data Submittal Form - Revised January 19, 2001

-------
RACT/BACT/LAER Clearinghouse Input Form, page 2 (Plantwide Information)
Source Name:	
Permit Number:
PLANTWIDE INFORMATION
Facility Notes:
Plant Information - Please include the following information on the facility being permitted:
Brief Plant Description/Narrative (for example - Chemical Plant, Steel Mill, Paint Manufacturing, etc.):
Brief Emission Source(s) Description (for example - boiler, paint spray booth, furnace, etc.):_
Type(s) of Fuel Used at this Facility:_
Description of the Pollution Abatement Strategy (for example - fabric filter, ESP, carbon adsorbers, powder coatings, etc.):_
Plantwide Emissions/Emissions Increase Information (Rate After Control):
Pollutant:	Emissions (t/yr):	Pollutant:	Emissions (t/yr):
Pollutant:
Emissions (T/YR):
NSR/RBLC Data Submittal Form - Revised January 19, 2001

-------
RACT/BACT/LAER Clearinghouse Input Form, page 3 (Process/Pollutant Information)
Source Name:	
Permit Number:
Process Information
Process Namc/Dcscriplion:_
RBLC Process Code:
SCC Code:
Throughput Capac i ly/S i/.c:
Primary Fuel:
Compliance Verified? Y
Process Notes :
N
If so. Bv What Method? (circle those that apply): Slack Test? Y N Calculation? Y N
Other Test? Y N Inspection? Y N
Other Method? 	
Pollutant Information
Pollutant Name:
CAS Number:
Pollution Reduction Method Description:
~ Pollution Prevention (P2) ~ Both P2 and Add-on
~ Add-on Control Device
~ No Controls Feasible
Pollution Prevention/Add-on Control Equipment Description:
Basis of Limit (circle one):
BACT-PSD
BACT-Other LAER
MACT
GACT
RACT
NSPS
NESHAPS
No. of Pollution Reduction Options Examined:.
Rank of Pollution Reduction Option Selected: .
Emission Limits: Primary:
Overall % Efficiency of Control/ Prevention System:	
Emission Type? (circle one): area point fugitive
Alternative:
RBLC Standard Emission Limit (where applicable):_
Pollution Control Cost Info: c°sts	0&M Costs:
Yes No
Annualized Costs:
Capital Costs:,
Costs are in
dollars.
(year)
Cost Effectiveness
($/T of poll, removed)!
Incremental Cost Effectiveness
($/T of poll, removed)!
OTHER
NSR/RBLC Data Submittal Form - Revised January 19, 2001

-------
RBLC Input Form, page 4 (Pollutant Information - continuation page) Source Name:	
Process Description:	Permit Number:	RBLC Process Code:
Information on Additional Pollutants
Pollutant Information	Pollution Reduction Method Description:
Pollutant Name: 	 CAS Number	° Pollution Prevention (P2) ~ Both P2 and Add-on
~ Add-on Control Device ~ No Controls Feasible
Pollution Prevention/Add-on Control Equipment Description:	
Basis of Limit (circle one): BACT-PSD BACT-Other LAER MACT GACT	RACT	NSPS	NESHAPS OTHER
No. of Pollution Reduction Options Examined:		Overall % Efficiency of Control/ Prevention System:	
Rank of Pollution Reduction Option Selected: 		Emission Type? (circle one): area point fugitive
Emission Limits: Primary:	Alternative:
RBLC Standard Emission Limit (where applicable):_
Costs verified by Agency?
Pollution Control Cost Info:	Yes No O & M Costs:	 Annualized Costs: 	 Capital Costs:.
Costs are in	dollars.
	(year)	
Cost Effectiveness	Incremental Cost Effectiveness
($/T of poll, removed): 	 ($/T of poll, removed):
Pollutant Information	Pollution Reduction Method Description:
Pollutant Name: 	 CAS Number: 	 ° Pollution Prevention (P2) ~ Both P2 and Add-on
~ Add-on Control Device ~ No Controls Feasible
Pollution Prevention/Add-on Control Equipment Description:
Basis of Limit (circle one): BACT-PSD BACT-Other LAER MACT GACT	RACT	NSPS	NESHAPS OTHER
No. of Pollution Reduction Options Examined:		Overall % Efficiency of Control/ Prevention System:	
Rank of Pollution Reduction Option Selected: 		Emission Type? (circle one): area point fugitive
Emission Limits: Primary:	Alternative:
RBLC Standard Emission Limit (where applicable):_
Costs verified by Agency?
Pollution Control Cost Info:	Yes No O & M Costs:	 Annualized Costs: 	 Capital Costs:.
Cost Effectiveness	Incremental Cost Effectiveness
Costs are in	dollars.	„
	-				($/T of poll, removed). 	 (V1 01 poll, removed).		

-------
Appendix A — Data Submittal Form and Instructions
INSTRUCTIONS FOR COMPLETING RACT/BACT/LAER CLEARINGHOUSE
INPUT FORM
1.	Company Name/Site Location: Insert name and address of the proposed facility. The
address should be the location of the proposed facility not the address of the parent
company unless they are the same.
2.	Plant/Facility Contact Information: The is a person knowledgeable about the process
at the plant or facility being permitted. Enter the name, telephone numbers (voice and
fax), e-mail address, and physical address of the plant contact. (A check box has been
provided if the plant's and the plant contact's physical address are the same.)
3.	Permitting Agency Contact Information: Indicate the person at the permitting agency
to whom requests should be directed. This should be the person most capable of
responding to factual questions concerning the source and processes subject to this
permitting action. Please provide area code with the phone number, E-mail address, and
conventional mail address.
4.	Physical Plant Location Information: List the Universal Transverse Mercator (UTM)
coordinates and UTM Zone of the facility being permitted. (This information is usually
listed on United States Geological Survey (USGS) maps of the area where the facility is
physically located.) The UTM coordinates are reported as Easting (X) and Northing (y).
Easting indicate the horizontal or x coordinate within the UTM Zone for the source and
Northing indicate the vertical or y coordinate within the UTM Zone for the source. The
RBLC needs this information to determine proximity of the source to Class I areas (e.g.,
National Parks, Wilderness Areas, etc.). Please list the names of the Class One Areas
within 100km of the source and Class One areas located within 100 to 250km of the
source and their distance to the source.
5.	Permit/File Number: This should be the identification number assigned by the agency
that issued the permit.
6.	ID Numbers and Codes: Fill-in the requested AIRS identification number, if available,
and the SIC code.
7.	Scheduling Information: Permitting scheduling dates stored include:
-	receipt of application (estimated or actual)
-	final permit issued (estimated or actual)
A-l

-------
-	start-up operation (estimated or actual)
-	compliance verification (estimated or actual)
Please enter all of the scheduling information available.
8.	Plantwide Emissions/Emissions Increase Information: Provide the name of each pollutant
emitted in significant amounts and indicate the maximum amount of emissions (tons/year)
that is anticipated for each pollutant (facility-wide, all processes) under this permit.
9.	Plantwide Information: Please describe the facility being permitted. Descriptions
should be summary and brief. Examples are as follows:
Plant Level - In brief terms, indicate what kind of plant this is; for example:
Integrated Steel Plant, Primary Aluminum Production, Publication Printing, Coil
Coating, Power Plant, Oil Refinery; Coffee Roasting; Wastewater Treatment Plant;
etc. A detailed narrative about the plant is not needed.
Source Level - List major processes that are part of the permitted source; for
example: boiler, turbine, coke oven, rotogravure printing press, solid waste
incinerator, coating line, lead smelter, air oxidation process, volatile organic liquid
storage, etc. A detailed narrative about the process is not needed.
Fuel Type - List all fuels that will be used at this facility; for example: coal, # 2
distillate oil, process gas, etc. Again, a detailed narrative about the fuels used is
not necessary.
Pollution Abatement Strategy - List all major pollution prevention and control
systems/devices that will be used to reduce or eliminate air pollution; for example:
powder coatings, low sulfur fuel, electrostatic precipitator, carbon adsorption, etc.
10.	Facility Notes: This section is for the completion or elaboration of any of the above
items where space was a problem. Also, any information that you feel other agencies
should know about this determination should appear here. Notes are typically used for the
following:
More than one permit number [See note under Permit Number.]
More detail on a particular process
More than one contact person
Further explanation regarding the designation of a source as new or modified
Further explanation of the emission limit or the support documentation associated
with setting the limit (i.e., limit based on design or stack test)
A-2

-------
11.	Process Description: List all processes subject to this permit by name (e.g., kiln, boiler)
for which a throughput limit, operating limit, emission limit, control strategy, performance
or equipment standard has been specified. Use additional pages as necessary. Additional
information on a process may be placed in the Process Notes section.
Process name or process equipment should be listed using one of the process categories
listed in Appendix C (Detailed Listing of Proposed Process Categories). A descriptor may
be added behind the generic category name. For example,
Boiler, coal-fired, 3 each
Kiln, 3 each
Conveyors, coal/limestone
Furnace, arc
Boiler, recovery
Boiler, power
Engines, gas-fired
12.	Process Type Code: A code assigned to each process (see Appendix B) used to
categorize determinations.
[We really need this so please use the drop-down list. Do not use the codes that end in
"000". The "000" code are category codes. Also, try and avoid using the codes that end
in "999" as they are catch-all categories. If you do not enter an RBLC Process code, we
will try to figure it out. If we cant, you will get a phone call.]
13.	SCC Code: This code is the standard source classification for processes used throughout
the Office of Air at EPA.
[We really need this so please use the drop-down list. If this is not listed, we will try to
figure it out. If we cant, you will get a phone call.]
14.	Throughput Capacity: Indicate the maximum design capacity of the unit. Use the same
units of measure used in the NSPS to describe the size of a source. Wherever possible,
use the list of standardized abbreviations for process and emission limit - Appendix D.
15.	Compliance Verification: This series of fields allows you to enter a yes or no response
to the following questions:
-	Compliance verified?
-	Method of confirmation:
Stack testing?
Other testing?
A-3

-------
Inspection?
Calculations?
You may also enter a narrative description of other types of confirmation methods.
[If you leave this field blank, it defaults to "no" to indicate that compliance was not
verified.]
16.	Process Notes: This field should contain any additional information on the process being
permitted.
17.	Pollutant(s) Emitted: Make an entry for each pollutant or parameter for which a control
requirement or other restraint has been specified (PM, SO, C02, N02, opacity, or others).
Use a separate block for each entry, and identify the pollutant and provide its Chemical
Abstracts (CAS) number. Use the following standard abbreviations for these common
pollutants whenever possible:
PM
Particulate Matter
SOX
Sulfur Oxides
NOX
Nitrogen Oxides
CO
Carbon Monoxide
VOC
Volatile Organic Compounds
VE
Visible Emissions
TRS
Total Reduced Sulfur
F
Fluoride
Be
Beryllium
h2s
Hydrogen Sulfide
Hg
Mercury
VC
Vinyl Chloride
Abbreviations for other pollutants are listed in Appendix D, along with CAS numbers.
[Use the drop-down list. To quickly get to say "PM,"just type a "P." This will move you
down the list to the start of the P's. We are working on cleaning up this list, but at this
time many pollutants are listed more than once. The one to choose is the one that lists the
pollutant name and its CAS number. For those pollutants that cover a range of pollutants
(PM, PM10, NOx, SOx, VOC, opacity etc) the RBLC uses a custom CAS number. For
example, these are the right drop-down entries in the Pollutant Name list to choose for the
examples listed above: PM - "PM,PM"; PM10 - 'PM10, PM"; NOx - "NOx, 10102";
SOx - "SOx, 7446"; VOC - "VOC, VOC"; opacity - "VE,VE".
Do not choose a pollutant that is not in the "name, CAS#" format because it will have to
A-4

-------
be changed. If you cannot find the pollutant you need to list in the drop-down, please
send me an e-mail at  and I will add it (along with its CAS
number) to the list.]
18.	Emission Limit(s): For consistency and ease of comparison, list the emission limit or rate
in the units of measure listed in Appendix C or those used in AP-42. Wherever possible
use the list of standard abbreviations (Appendix D).
There are multiple emission limits in the Clearinghouse, they are:
Primary emission limit and units: The primary emission limit listed in the permit.
Alternate emission limit and units: If provided on the permit, these numbers
represent any alternate emission measurements which the facility may make.
Standardized limit and units: This limit allows comparison with other similar
determinations in the RBLC. Standard units are provided for certain process types
(see Appendix D) so that users can compare the entries in this field to determine
the most stringent limits.
The base-line limit is no longer used in the RBLC data base.
19.	Emission Type: A one-character field indicating whether the emission is fugitive, point-
source, or area-source.
20.	Pollution Reduction Ranking Information: Two pieces of information are requested:
The number of options examined and the rank of the option selected. The "rank" is the
number of the option selected when the options are ordered according to the performance
of the system. Number 1 would be the best controlled system, number 2 would be the
next best, etc.
21.	Regulatory Requirements Associated with Limit (Basis of Limit): Indicate the
regulatory requirement that precipitated establishing the limit presented, i.e., BACT-PSD,
BACT-Other, LAER, MACT, RACT, GACT, NSPS, NESHAP, or Other. Do not list
such items as stack test, design or others. These items generally represent the supporting
information that may have been used to document or establish the given limit. Such items
should be included in the notes section.
To facilitate the identification of limits use the following abbreviations:
-	BACT-PSD (Prevention of Significant Deterioration)
-	BACT-Other (regulated by State/local rules, not PSD)
-	LAER (lowest Available Control Technology)
A-5

-------
-	MACT (Maximum Achievable Control Technology)
-	RACT (Reasonably Available Control Technology)
-	GACT (Generally Available Control Technology)
-	NSPS (New source Performance Standards)
-	NESHAP (National Emission Standards for Hazardous Air Pollutants)
-	Other
22.	Pollution Reduction Method Description: Describe the specific pollution prevention
techniques and add-on equipment used to achieve the permitted emission limits. Specify
"NONE" if no controls are feasible. Pollution prevention techniques include operational
modifications, limits in the type and amount of raw materials used, limits on throughput or
hours of operation, maintenance requirements, equipment specifications, or other
limitations. Typical add-on equipment includes ESP, fabric filter, etc. Information in this
section may be supplemented under the "Notes" section.
Please note that the RBLC no longer has separate fields for equipment manufacturer and
model number. Place this information, if you have it, in the notes.
[Please note that if you specify "NONE" for this field and then enter something in the
Description field, you will get a phone call asking you if you really meant to put "NONE."
23.	Overall Efficiency %: Enter the overall system pollution reduction efficiency, consisting
of capture (hoods, ductwork, etc.) and collection (control device) efficiency. Any
breakdown of efficiencies for capture or collection individually should be shown under
"Notes." For P2, indicate the overall effectiveness of the P2 methods.
24.	Cost Data: Pollution reduction costs include:
-	Year of the dollar used in cost calculations
-	Cost verified by the permitting agency (yes or no)
-	Cost effectiveness in dollars per ton (annualized cost/tons of pollutant removed)
-	Capital cost of control equipment
-	Annual operation and maintenance cost for all control methods
-	Annualized cost (amortized capital cost + annual operation & maintenance costs)
A-6

-------
When you have completed the form, mail it to the following address:
RACT/BACT/LAER CLEARINGHOUSE
RBLC (MD-12)
US EPA
RTP, NC 27711
A-7

-------
APPENDIX B
AGENCY CODE LISTING

-------
This page has been intentionally left blank.

-------
Appendix B — Agency Code Listing
ALABAMA
AL001	Alabama Dept of Environmental Mgmt
AL002	Huntsville Air Poll Control Agency, AL
AL003	Jefferson Co Department of Health, AL
AL999	Other Alabama
ALASKA
AK001	Alaska Dept of Environmental Cons
AK002	Fairbanks North Star Borough, AK
AK003	S. Central Air, Anchorage APCA, AK
AK999	Other Alaska
AMERICAN	SAMOA
AS001	American Samoa Env Quality Commission
AS999	Other American Samoa
ARIZONA
AZ001	Arizona Dept of Env Qual, Ofc of Air Qua
AZ002	Maricopa Co Air Pollution Control, AZ
AZ003	Pima Co Dept of Env Quality, AZ
AZ004	Pinal Co Air Quality Control Dist, AZ
AZ999	Other Arizona
ARKANSAS
AR001	Arkansas Dept of Poll Ctrl & Ecology
AR999	Other Arkansas
CALIFORNIA
CA001	California Air Resources Board
CA002	Amador County APCD, CA
CA003	Bay Area AQMD, CA
CA004	Butte County APCD, CA
CA005	Calaveras County APCD, CA
B-l

-------
CA006
Colusa County APCD, CA
CA007
El Dorado County APCD, CA
CA046
Feather River AQMD, CA
CA0081
Fresno APCD, CA
CA009
Glenn County APCD, CA
CA010
Great Basin Unified APCD, CA
CA011
Imperial County APCD, CA
CA012
Kern County APCD, CA
CA0134
Kings County APCD, CA
CA014
Lake County AQMD, CA
CA015
Lassen County APCD, CA
CA0164
Madera County APCD, CA
CA017
Mariposa County APCD, CA
CA018
Mendocino County AQMD, CA
CA0194
Merced County APCD, CA
CA020
Modoc County APCD, CA
CA029
Mojave Desert AQMD, CA
CA021
Monterey Bay Unified APCD, CA
CA0224
Mountain Counties Air Basin, CA
CA023
North Coast Unified AQMD, CA
CA024
Northern Sierra AQMD, CA
CA025
Northern Sonoma County APCD, CA
CA026
Placer County APCD, CA
CA0274
Plumas County Env. Health Department, CA
CA028
Sacramento Metropolitan AQMD, CA
CA030
San Diego County APCD, CA
CA047
San Joaquin Valley Unified APCD - Central Regional Office, CA
CA048
San Joaquin Valley Unified APCD - Northern Regional Office, CA
CA049
San Joaquin Valley Unified APCD - Southern Regional Office, CA
CA032
San Luis Obispo County APCD, CA
CA033
Santa Barbara County APCD, CA
CA034
Shasta County AQMD, CA
CA035
Siskiyou County APCD, CA
CA036
South Coast AQMD, CA
CA0374
Standards County APCD, CA
CA0384
Stanislaus County APCD, CA
CA0394
Sutter County APCD, CA
CA040
Tehama County APCD, CA
CA0414
Tulare County APCD, CA
CA042
Tuolumne County APCD, CA
CA043
Ventura County APCD, CA
CA044
Yolo-Solano APCD, CA
CA0454
Yuba County APCD, CA
1 No longer active. Listed for historical purposes only.
B-2

-------
CA999	Other California
COLORADO

COOOl
Colorado Dept of Health - Air Poll Ctrl
CO002
Boulder County Health Department, CO
CO003
Denver City-Co Air Qual/Env Prot, CO
CO004
El Paso County Health Department, CO
CO005
Jefferson Co Dept of Health & Env, CO
CO006
Larimer Co Health Dept, Env Health, CO
CO007
Mesa County Health Department, CO
CO008
Pueblo City-County Health Department, CO
CO009
Weld County Health Department, CO
C0999
Other Colorado
CONNECTICUT
CT001
Connecticut Bureau of Air Management
CT002
Bristol-Burlington Health Department, CT
CT003
City ofMeriden, Dept Human Serv, CT
CT004
Dept of Air Poll Ctrl, Bridgeport, CT
CT005
Greenwich Department of Health, CT
CT006
New Haven Health Department, CT
CT007
Norwalk Department of Health, CT
CT008
Stamford Health Department, CT
CT009
Stratford Department of Health, CT
CT999
Other Connecticut
DELAWARE

DE001
Delaware Dept of Natural Res & Env Ctrl
DE999
Other Delaware
DISTRICT OF COLUMBIA
DC001
DC Air Qual Control & Monitoring Branch
DC999
Other District of Columbia
FLORIDA

FL001
FL002
FL003
FL004
FL005
Florida Dept of Env Regulation
Broward Co Ofc of Nat Res Prot, FL
City of Jacksonville, FL
Hillsborough Co Env Prot Comm, FL
Jacksonville, Bio-Environmental Serv, FL

-------
FL006	Manatee County Public Health Unit, FL
FL007	Metro Dade Co Dept of Env Res Mgmt, FL
FL008	Palm Beach County Public Health Unit, FL
FL009	Pinellas Co Dept of Env Mgmt, FL
FLO 10	Sarasota County Air Program, FL
FL999	Other Florida
GEORGIA
GA001	Georgia Department of Natural Resources
GA999	Other Georgia
GUAM
GU001	Guam Environmental Protection Agency
GU999	Other Guam
HAWAII
HI001	Hawaii Clean Air Branch
HI999	Other Hawaii
IDAHO
ID001	Idaho Dept of Health & Welfare
ID999	Other Idaho
ILLINOIS
IL001	Illinois EPA, Div of Air Poll Control
IL002	Bedford Park Env Qual Ctrl Board, IL
IL003	Bensenville Air Poll Control Dist, IL
IL004	City of Chicago, Env Prot Div, IL
IL005	City of Evanston-Dept Bldg & Zoning, IL
IL006	Cook Co Dept of Env Control, IL
IL007	Dupage County Health Department, IL
IL008	Village of McCook Env Board, IL
IL999	Other Illinois
INDIANA
IN001	Indiana Dept of Env Mgmt, Ofc of Air
IN002	Anderson Air Pollution Control Dept, IN
IN003	E. Chicago Dept of Air Qual Control, IN
IN004	Evansville Air Pollution Control, IN
B-4

-------
IN005	Gary Air Pollution Control, IN
IN006	Hammond Air Pollution Control Dept, IN
IN007	Indianapolis Air Poll Control Div, IN
IN008	Lake County Air Pollution Control, IN
IN009	St. Joseph County Air Poll Control, IN
IN010	Vigo County Air Pollution Control, IN
IN999	Other Indiana
IOWA
IA001	Iowa Department of Natural Resources
IA002	Linn County Health Department, IA
IA003	Polk County Physical Planning Dept, IA
IA999	Other Iowa
KANSAS
KS001	Kansas Bureau of Air and Waste Mgmt
KS002	Kansas City/Wyandotte Co Health Dept, KS
KS003	Topeka-Shawnee County Health Agency, KS
KS004	Wichita-Sedgwick Co Comm Health Dept, KS
KS999	Other Kansas
KENTUCKY
KY001	Kentucky DEP, Div for Air Quality
KY002	Jefferson Co APCD, KY
KY999	Other Kentucky
LOUISIANA
LA001	Louisiana Department of Env Quality
LA999	Other Louisiana
MAINE
MEOO1	Maine Department of Env Protection
ME999	Other Maine
MARYLAND
MD001	Maryland Department of the Environment
MD002	Allegany County Health Department, MD
MD003	Anne Arundel Co Air Qual Cont Prog, MD
MD004	Baltimore City Health Department, MD
B-5

-------
MD005	Baltimore Co Bur Air Qual/Waste Mgmt, MD
MD006	Frederick County Health Department, MD
MD007	Harford County Health Department, MD
MD008	Howard County Health Department, MD
MD009	Montgomery County DEP, MD
MD010	Prince George's County Health Dept, MD
MD999	Other Maryland
MASSACHUSETTS
MA001	Massachusetts Div of Air Qual Control
MA002	Berkshire and Pioneer Valley APCD, MA
MA003	Boston Air Pollution Control Comm, MA
MA004	Massachusetts DEP, Central Reg Air Qual
MA005	Merrimack Valley & Metro Boston APCD, MA
MA006	SE Massachusetts Air Poll Ctrl Dist, MA
MA999	Other Massachusetts
MICHIGAN
MI001	Michigan Department of Natural Resources
MI002	City of Grand Rapids Env Serv Dept, MI
MI003	Wayne County Air Poll Control Div, MI
MI999	Other Michigan
MINNESOTA
MN001	Minnesota Poll Ctrl Agcy, Air Qual Div
MN002	City of Bloomington, Env Poll Sec, MN
MN003	City of Richfield, Air Poll Ctrl, MN
MN004	Minneapolis Pollution Control Div, MN
MN005	St. Louis Park Inspectional Serv, MN
MN999	Other Minnesota
MISSISSIPPI
MS001	Mississippi Dept of Env Quality
MS999	Other Mississippi
MISSOURI
MOOOl	Missouri DNR, Air Poll Control Program
MO002	City of St. Louis Air Poll Ctrl, MO
MO003	Greene Co-City of Springfield APCA, MO
MO004	Kansas City, MO, Air Quality Section
B-6

-------
M0005
M0999
St. Louis Co Air Poll Control Br, MO
Other Missouri
MONTANA
MT001	Montana Dept of Environmental Quality
MT002	Cascade City-Co Air Poll Ctrl Prog, MT
MT003	Missoula City-County Health Dept, MT
MT004	Yellowstone County Air Poll Control, MT
MT999	Other Montana
NEBRASKA
NEOO1	Nebraska Dept of Env Control
NE002	Lincoln-Lancaster Co Health Dept, NE
NE003	Omaha City Air Quality Control Div, NE
NE999	Other Nebraska
NEVADA
NV001	Nevada Dept of Cons and Natural Res
NV002	Clark Co Health Dist, Div APC, NV
NV003	Washoe County District Health Dept, NV
NV999	Other Nevada
NEW HAMPSHIRE
NH001	New Hampshire Dept of Env Serv, Air Res
NH999	Other New Hampshire
NEW JERSEY
NJ001	New Jersey Dept of Env Protection
NJ002	City of Elizabeth City Hall, NJ
NJ003	Hudson Regional Health Commission, NJ
NJ004	Middlesex Co Air Poll Ctrl Prog, NJ
NJ999	Other New Jersey
NEW MEXICO
NMOO1	New Mexico Env Improvement Div/Air Qual
NM002	Albuquerque Env Health & Energy Dept NM
NM999	Other New Mexico
NEW YORK
B-7

-------
NY001	New York DEC, Div of Air Resources
NY002	Albany County Dept of Health, NY
NY003	Interstate Sanitation Commission, NY
NY004	Monroe County Department of Health, NY
NY005	Nassau Co DOH, Center for Env Prot, NY
NY006	New York City Bureau of Air Res, NY
NY007	Niagara Co Health Dept, Air Res Bur, NY
NY008	Rensselaer Co DOH, Div of Env Health, NY
NY009	Rockland Co DOH, Air Poll Ctrl, NY
NYO10	Suffolk Co Ofc of Haz Mat Mgmt, NY
NY011	Westchester County Dept of Health, NY
NY999	Other New York
NORTH CAROLINA
NCOO1	North Carolina Div of Env Mgmt
NC002	Cleveland County Health Department, NC
NC003	Cumberland Co Air Pollution Control, NC
NC004	Forsyth County Env Affairs Dept, NC
NC005	Mecklenburg Co Dept of Env Prot, NC
NC006	W. North Carolina Reg Air Poll Ctrl Bd
NC999	Other North Carolina
NORTH DAKOTA
ND001	North Dakota State Department of Health
ND999	Other North Dakota
OHIO
OHOOl	Ohio Environmental Protection Agency
OH002	Akron Reg Air Quality Mgmt Dist, OH
OH003	Canton Air Pollution Control Div, OH
OH004	City of Toledo, Env Services Div, OH
OH005	Cleveland Div of Air Poll Control, OH
OH006	Hamilton Co-Southwestern OH APCA
OH007	Lake County General Health District, OH
OH008	Mahoning-Trumbull Air Poll Ctrl Agcy, OH
OH009	Montgomery Co Reg Air Poll Ctrl Agcy, OH
OHO 10	North Ohio Valley Air Authority, OH
OHOl 1	Portsmouth Local Air Agency, OH
OHO 12	Dayton Regional Air Poll Ctrl Agency, OH
OH999	Other Ohio
OKLAHOMA
B-8

-------
OKOOl	Oklahoma Air Quality Service
OK002	City-Co Health Dept of Oklahoma City
OK003	Tulsa City-County Health Department, OK
OK999	Other Oklahoma
OREGON
OROOl	Oregon Dept of Environmental Quality
OR002	Lane Regional Air Poll Authority, OR
OR999	Other Oregon
PENNSYLVANIA
PA001	Pennsylvania DER, Bur of Air Qual Ctrl
PA002	Allegheny Co Bureau of Air Poll Ctrl, PA
PA003	Philadelphia DOPH, Air Mgmt Serv, PA
PA999	Other Pennsylvania
PUERTO RICO
PR001	Puerto Rico Env Quality Board
PR999	Other Puerto Rico
RHODE ISLAND
RI001	Rhode Island Div of Air & Haz Mat
RI999	Other Rhode Island
SOUTH CAROLINA
SC001	South Carolina Dept of Health & Env Ctrl
SC002	City of Columbia Air Poll Control, SC
SC999	Other South Carolina
SOUTH DAKOTA
SDOO1	South Dakota Dept of Water & Nat'l Res
SD999	Other South Dakota
TENNESSEE
TN001	Tennessee Div of Air Pollution Control
B-9

-------
TN002	Chattanooga-Hamilton Co APCB, TN
TN003	Knox Co Dept of Air Poll Control, TN
TN004	Memphis and Shelby Co Health Dept, TN
TN005	Metro Health/Nashville & Davidson Co, TN
TN999	Other Tennessee
TEXAS
TX001	Texas Air Control Board
TX002	City of Dallas, Health & Human Serv, TX
TX003	City of Houston, Bureau Air Qual Cont, TX
TX004	El Paso County Health Unit, TX
TX005	Fort Worth Air Pollution Control, TX
TX006	Galveston County Health District, TX
TX007	Harris County Pollution Control Dept, TX
TX008	Lubbock City Health Department, TX
TX999	Other Texas
UTAH
UT001	Utah Bureau of Air Quality
UT999	Other Utah
VERMONT
VT001	Vermont Air Pollution Control Division
VT999	Other Vermont
VIRGIN ISLANDS
VI001	Virgin Islands Dept of Planning, Nat Res
VI999	Other Virgin Islands
VIRGINIA
VA001	Virginia Environmental Quality Air Division
VA999	Other Virginia
WASHINGTON
WA001	Washington State Department of Ecology
WA002	Benton-Franklin-Walla Walla Co APA, WA
WA003	Northwest Air Pollution Authority, WA
B-10

-------
WA004	Olympic Air Poll Control Authority, WA
WA005	Puget Sound Air Poll Control Agency, WA
WA006	Southwest Air Poll Ctrl Authority, WA
WA007	Spokane Co Air Poll Control Auth, WA
WA008	Yakima County Clean Air Authority, WA
WA999	Other Washington
WEST VIRGINIA
WV001 West Virginia Air Pollution Control Comm
WV999 Other West Virginia
WISCONSIN
WI001
WI002
WI003
WI004
WI999
WYOMING
WY001 Wyoming Air Qual Div, Dept of Env Qual
WY999 Other Wyoming
OTHER
OTOOl
National Park Service
OT002
EPA Region I
OT003
EPA Region II
OT004
EPA Region III
OT005
EPA Region IV
OT006
EPA Region V
OT007
EPA Region VI
OT008
EPA Region VII
OT009
EPA Region VIII
OTOIO
EPA Region IX
OTOll
EPA Region X
Wisconsin Dept of Natural Resources
Eau Claire City-Co Health Dept, WI
Madison Department of Public Health, WI
Milwaukee Co DPW, Env Serv Sec, WI
Other Wisconsin
B-ll

-------
APPENDIX C
PROCESS TYPE CODE LISTING

-------
This page has been intentionally left blank.
B-13

-------
Appendix C — Process Code Listing
10.000 COMBUSTION
11.000	EXTERNAL COMBUSTION
11.001	Bagasses Combustion
11.002	Coal Combustion
11.006	Fuel Oil Combustion
11.003	Lignite Combustion
11.004	Multiple Fuels Combustion
11.005	Natural Gas Combustion
11.007	Waste Oil Combustion
11.008	Wood/Wood Waste Combustion
11.999 Other External Combustion Sources
15.000	INTERNAL COMBUSTION
15.001	Aviation Fuels
15.002	Diesel Fuel
15.006	Fuel Oil
15.003	Gasoline
15.007	Multiple Fuels
15.004	Natural Gas
15.005	Process Gas
15.999 Other Internal Combustion Sources
20.000 WASTE DISPOSAL
21.000	MUNICIPAL WASTE
21.001	Municipal Waste Combustors/Incinerators
21.002	Municipal Waste Landfills
21.003	Publicly Owned Treatment Works (POTW) Emissions (except 21.004)
21.004	Sewage Sludge Incineration
21.999 Other Municipal Waste Processing/Disposal Facilities
C-l

-------
CODE PROCESS TYPE
22.000	HAZARDOUS WASTE
22.007 Asbestos Demolition, Renovation, and Disposal
22.001	Benzene Waste Treatment
22.006 Contaminated Soil Treatment
22.002	Hazardous Waste Incineration
22.003	Hazardous Waste Landfills
22.004	Site Remediation
22.005	Treatment, Storage and Disposal Facilities (TSDF) (except 22.002, 22.003 & 22.006)
22.999 Other Hazardous Waste Processing/Disposal Facilities
29.000	OTHER WASTE DISPOSAL (except 21 & 22)
29.001	Automobile Body Shredding/Incineration
29.002	Industrial Wastewater/Contaminated Water Treatment
29.003	Industrial Landfills
29.004	Medical/Infectious Waste Incineration
29.999 Other Waste Disposal Sources
30.000	WOOD PRODUCTS INDUSTRY
30.001	Charcoal
30.002	Kraft Pulp Mills
30.003	Plywood and Veneer Operations
30.004	Pulp and Paper Production other than Kraft
30.005	Reconstituted Panelboard Plants (waferboard, particleboard, etc.)
30.006	Wood Treatment
30.007	Woodworking
30.999 Other Wood Products Industry Sources
40.000 ORGANIC EVAPORATIVE LOSSES
41.000 SURFACE COATING/PRINTING/GRAPHIC ARTS
C-2

-------
CODE PROCESS TYPE
41.001	Aerospace Surface Coating
41.002	Automobiles and Trucks Surface Coating (OEM)
41.003	Automotive Refinishing
41.004	Can Surface Coating
41.005	Fabric Coating/Printing/Dyeing (except 41.017)
41.006	Flatwood Paneling Surface Coating
41.007	Flexible Vinyl & Urethane Coating/Printing
41.008	Large Appliance Surface Coating
41.026 Leather Surface Coating
41.009	Magnetic Tape Surface Coating
41.010	Magnetic Wire Surface Coating
41.011	Metal Coil Surface Coating
41.012	Metal Furniture Surface Coating
41.013	Miscellaneous Metal Parts and Products Surface Coating
41.014	Paper, Plastic & Foil Web Surface Coating (except 41.007 & 41.018)
41.015	Plastic Parts for Business Machines Surface Coating
41.016	Plastic Parts & Products Surface Coating (except 41.015)
41.017	Polymeric Coating of Fabrics
41.018	Pressure Sensitive Tapes and Labels Coating
41.019	Printing - Forms
41.020	Printing - News Print
41.021	Printing - Packaging
41.022	Printing - Publication
41.023	Printing/Publication (except 41.007 & 41.019-022)
41.024	Ship Building & Repair Surface Coating
41.025	Wood Products/Furniture Surface Coating (except 41.006)
41.999 Other Surface Coating/Printing/Graphic Arts Sources
42.000	LIQUID MARKETING (PETROLEUM PRODUCTS, GASOLINE, VOL)
42.001	Gasoline Bulk Plants
42.002	Gasoline Bulk Terminals
42.003	Gasoline Marketing (except 42.001 & 42.002)
42.004	Petroleum Liquid Marketing (except 42.001-003 & 42.005-006)
42.005	Petroleum Liquid Storage in Fixed Roof Tanks
42.006	Petroleum Liquid Storage in Floating Roof Tanks
42.009	Volatile Organic Liquid Storage
42.010	Volatile Organic Liquid Marketing (except 42.009)
C-3

-------
CODE PROCESS TYPE
42.999 Other Liquid Marketing Sources
49.000	ORGANIC EVAPORATIVE LOSSES (except 41 & 42)
49.001	Aerosol Can Filling
49.012	Architectural & Industrial Maintenance (AIM) Coatings
49.013	Automobile Refinish Coatings
49.011 Consumer Products
49.002	Dry Cleaning - PERC/Chlorinated Solvents
49.003	Dry Cleaning - Petroleum Solvents
49.004	Fiberglass Boat Manufacturing
49.005	Fiberglass/Reinforced Polymer Products Manufacturing (except 49.004)
49.006	Halogenated Solvent Cleaners
49.007	Ink Manufacturing
49.008	Organic Solvent Cleaning & Degreasing (except 49.006)
49.009	Paint/Coating/Adhesives Manufacturing
49.010	Paint Stripping
49.999 Other Organic Evaporative Loss Sources
50.000	PETROLEUM/NATURAL GAS PRODUCTION AND REFINING
50.001	Oil and Gas Field Services
50.002	Natural Gas/Gasoline Processing Plants
50.003	Petroleum Refining Conversion Processes (cracking, CO boilers, reforming, alkylation,
polymerization, isomerization, coking)
50.007	Petroleum Refining Equipment Leaks/Fugitive Emissions
50.004	Petroleum Refining Feedstock (blending, loading and unloading)
50.008	Petroleum Refining Flares and Incinerators (except acid gas/sulfur recovery unit
incinerators - 50.006)
50.005	Petroleum Refining Separation Processes (distillation and light ends recovery)
50.006	Petroleum Refining Treating Processes (hydrodesulfurization, hydrotreating, chemical
sweetening, acid gas removal, deasphalting, sulfur recovery units, acid gas/sulfur recovery
unit incinerators)
50.009	Petroleum Refining Wastewater and Wastewater Treatment
50.010	Shale Processing
50.999 Other Petroleum/Natural Gas Production & Refining Sources (except 50.001-010 and
42.000 - Liquid Marketing
C-4

-------
CODE PROCESS TYPE
60.000 CHF.MTCAUS MANUFACTURING
61.000	AGRICULTURAL CHEMICALS MANUFACTURING
61.001	2,4-D Salts and Esters Production
61.002	4-Chloro-2-Methylphenoxyacetic Acid Production
61.003	4,6-Dinitro-o-Cresol Production
61.004	Captafol (tm) Production
61.005	Captan (tm) Production
61.006	Chloroneb (tm) Production
61.007	Chlorthalonil (tm) Production
61.008	Dacthal (tm) Production
61.012 Fertilizer Production (except 61.009)
61.009	Phosphate Fertilizers Production
61.010	Sodium Pentachlorophenate Production
61.011	Tordon Acid Production
61.999 Other Agricultural Chemical Manufacturing Sources
62.000	INORGANIC CHEMICALS MANUFACTURING
62.001	Ammonium Sulfate Production - Caprolactam By-Product Plants
62.002	Antimony Oxides Manufacturing
62.003	Chlorine Production
62.016	Chloroalkali Production
62.004	Chromium Chemicals Manufacturing
62.005	Cyanuric Chemicals Manufacturing
62.006	Fume Silica Production
62.007	Hydrochloric Acid Production
62.017	Hydrofluoric Acid Production
62.008	Hydrogen Cyanide Production
62.009	Hydrogen Fluoride Production
62.020 Inorganic Liquid/Gas Storage & Handling
62.014 Nitric Acid Plants
62.010	Phosphoric Acid Manufacturing
62.011	Quaternary Ammonium Compounds Production
62.018	Sodium Carbonate Production
C-5

-------
CODE PROCESS TYPE
62.012	Sodium Cyanide Production
62.015 Sulfuric Acid Plants
62.019 Sulfur Recovery (except 50.006)
62.013	Uranium Hexafluoride Production
62.999 Other Inorganic Chemical Manufacturing Sources
63 .000 POLYMER AND RESIN PRODUCTION
63.001	Acetal Resins Production
63.002	Acrylonitrile-Butadiene-Styrene Production
63.003	Alkyd Resins Production
63.004	Amino Resins Production
63.005	Butadiene-Furfural Cotrimer (R-ll)
63.006	Butyl Rubber Production
63.007	Carboxymethylcellulose Production
63.008	Cellophane Production
63.009	Cellulose Ethers Production
63.010	Epichlorohydrin Elastomers Production
63.011	Epoxy Resins Production
63.012	Ethylene-propylene Rubber Production
63.013	Flexible Polyurethane Foam Production
63.014	Hypalon (tm) Production
63.015	Maleic Copolymers Production
63.016	Methylcellulose Production
63.017	Methyl Methacrylate-Acrylonitrile-Butadiene-Styrene Production
63.018	Methyl Methacrylate-Butadiene-Styrene Terpolymers Production
63.019	Neoprene Production
63.020	Nitrile Butadiene Rubber Production
63.021	Non-Nylon Polyamides Production
63.022	Nylon 6 Production
63.023	Phenolic Resins Production
63.024	Polybutadiene Rubber Production
63.025	Polycarbonates Production
63.026	Polyester Resins Production
63.027	Polyether Polyols Production
63.028	Polyethylene Terephthalate Production
63.029	Polymerized Vinylidene Production
63.030	Polymethyl Methacrylate Resins Production
C-6

-------
CODE PROCESS TYPE
63.031	Polystyrene Production
63.032	Polysulfide Rubber Production
63.033	Polyvinyl Acetate Emulsions Production
63.034	Polyvinyl Alcohol Production
63.035	Polyvinyl Butyral Production
63.036	Polyvinyl Chloride and Copolymers Production
63.037	Reinforced Plastic Composites Production
63.038	Styrene-Acrylonitrile Production
63.039	Styrene Butadiene Rubber and Latex Production
63.999 Other Polymer and Resin Manufacturing Sources
64.000	SYNTHETIC ORGANIC CHEMICAL MANUFACTURING INDUSTRY
(SOCMI)
64.001	Batch Reaction Vessels (except 69.011)
64.002	Equipment Leaks (valves, compressors, pumps, etc.)
64.003	Processes Vents (emissions from air oxidation, distillation, and other reaction vessels)
64.004	Storage Tanks (SOCMI Chemicals (loading/unloading, filling, etc.)
64.005	Transfer of SOCMI Chemicals (loading/unloading, filling, etc.)
64.006	Wastewater Collection & Treatment
64.999 Other SOCMI Industry Sources
65.000	SYNTHETIC FIBERS PRODUCTION
65.001	Acrylic Fibers/Modacrylic Fibers Production
65.002	Rayon Production
65.003	Spandex Production
65.999 Other Synthetic Fibers Production Sources
69.000	CHEMICAL MANUFACTURING (except 61, 62, 63, 64 & 65)
69.001	Benzyltrimethylammonium Chloride Facilities
69.002	Butadiene Dimers Production
69.015 Carbon Black Manufacturing
69.003	Carbonyl Sulfide Production
69.004	Chelating Agents Production
C-7

-------
CODE PROCESS TYPE
69.005	Chlorinated Paraffins Production
69.006	Dodecanedioic Acid Production
69.007	Ethylidene Norbornene Production
69.008	Explosives Production
69.009	Hydrazine Production
69.010	OBPA/l,3-Diisocyanate Production
69.011	Pharmaceuticals Production
69.012	Photographic Chemicals Production
69.013	Phthalate Plasticizers Production
69.017 Propellant Manufacturing & Production
69.014	Rubber Chemicals Manufacturing
69.016 Soap & Detergent Manufacturing
69.999 Other Chemical Manufacturing Sources
70.000	FOOD AND AGRICULTURAL PRODUCTS (also see 61 - AGRICULTURAL
CHEMICALS)
70.016 Alcohol Fuel Production
70.008	Alcoholic Beverages Production
70.001	Alfalfa Dehydrating
70.002	Baker's Yeast Manufacturing
70.003	Bread Bakeries
70.004	Cellulose Food Casing Manufacturing
70.005	Coffee Roasting
70.006	Cotton Ginning
70.007	Feed and Grain Handling, Storage & Processing (including Mills and Elevators)
70.009	Fish Processing
70.010	Fruit and Vegetable Processing
70.011	Meat Smokehouses
70.012	Roasting (except 70.005)
70.013	Starch Manufacturing
70.014	Sugar Cane Processing
70.015	Vegetable Oil Production
70.999 Other Food and Agricultural Products Sources
80.000 METALLURGICAL INDUSTRY
C-8

-------
CODE PROCESS TYPE
81.000	FERROUS METALS INDUSTRY
81.001	Coke By-product Plants
81.002	Coke Production (except 81.001)
81.003	Ferroalloy Production
81.004	Iron Foundries
81.005	Stainless Steel/Specialty Steel Manufacturing
81.006	Steel Foundries
81.007	Steel Manufacturing (except 81.005 & 81.006)
81.008	Steel Pickling - HCL Process
81.999 Other Ferrous Metals Industry Sources
82.000	NONFERROUS METALS INDUSTRY
82.016 Beryllium Processing and Manufacturing
82.001	Lead Acid Battery Manufacturing
82.002	Lead Acid Battery Reclamation
82.003	Lead Oxide and Pigment Production
82.004	Lead Products (except 82.001-002, 82.006 & 82.012)
82.005	Primary Aluminum Production
82.006	Primary Copper Smelting
82.007	Primary Lead Smelting
82.008	Primary Magnesium Refining
82.009	Primary Zinc Smelting
82.010	Secondary Aluminum Production
82.011	Secondary Brass & Brass Ingot Production
82.012	Secondary Copper Smelting & Alloying
82.013	Secondary Lead Smelting
82.014	Secondary Magnesium Smelting
82.015	Secondary Zinc Processing
82.999 Other Non-Ferrous Metals Industry Sources
90.000	MINERAL PRODUCTS
90.001	Alumina Processing
90.035 Asbestos Manufacturing
C-9

-------
CODE PROCESS TYPE
90.002	Asphalt/Coal Tar Application - Metal Pipes
90.003	Asphalt Concrete Manufacturing
90.004	Asphalt Processing (except 90.002, 90.003 & 90.034)
90.034 Asphalt Roofing Products Manufacturing
90.017 Calciners & Dryers and Mineral Processing Facilities
90.005	Calcium Carbide Manufacturing
90.006	Cement Manufacturing (except 90.028)
90.007	Chromium Refractories Production
90.008	Clay and Fly Ash Sintering
90.009	Clay Products (including Bricks & Ceramics)
90.010	Coal Conversion/Gasification
90.011	Coal Handling/Processing/Preparation/Cleaning
90.012	Concrete Batch Plants
90.013	Elemental Phosphorous Plants
90.014	Frit Manufacturing
90.015	Glass Fiber Manufacturing (except 90.033)
90.016	Glass Manufacturing
90.017	Calciners
90.018	Lead Ore Crushing and Grinding
90.019	Lime/Limestone Handling/Kilns/Storage/Manufacturing
90.020	Mercury Ore Processing
90.021	Metallic Mineral/Ore Processing (except 90.018, 90.020 & 90.031)
90.022	Mineral Wool Manufacturing
90.023	Mining Operations (except 90.032)
90.024	Non-metallic Mineral Processing (except 90.011, 90.019, 90.017, 90.026) (NOTE: This
category includes stone quarrying, sand and gravel processing, gypsum processing, perlite
processing and all other non-metallic mineral/ore processing.)
90.026	Phosphate Rock Processing
90.027	Phosphogypsum Stacks
90.028	Portland Cement Manufacturing
90.029	Refractories
90.031	Taconite Iron Ore Processing
90.032	Underground Uranium Mines
90.033	Wool Fiberglass Manufacturing
90.999 Other Mineral Processing Sources
C-10

-------
CODE PROCESS TYPE
99.000	MISCELLANEOUS SOURCES
99.001	Abrasive Blasting
99.002	Chromic Acid Anodizing
99.003	Comfort Cooling Towers
99.004	Commercial Sterilization Facilities
99.005	Decorative Chromium Electroplating
99.006	Electronics Manufacturing (except 99.011)
99.013	Electroplating/Plating (except Chrome - 99.002, 99.005 & 99.007)
99.019	Geothermal Power
99.007	Hard Chromium Electroplating
99.008	Hospital Sterilization Facilities
99.009	Industrial Process Cooling Towers
99.017	Leather Tanning
99.014	Polystyrene Foam Products Manufacturing
99.016 Polyurethane Foam Products Manufacturing
99.020	Rocket Demilitarization
99.010	Rocket Engine Test Firing
99.015	Rubber Tire Manufacturing and Retreading
99.011	Semiconductor Manufacturing
99.018	Synthetic Fuels Production (except 70.016 & 90.010)
99.012	Welding & Grinding
99.999 Other Miscellaneous Sources
C-ll

-------
APPENDIX D
ABBREVIATIONS FOR PROCESSES, UNITS, AND
POLLUTANTS

-------
This page has been intentionally left blank.

-------
Appendix D — Abbreviations for Processes. Units, and Pollutants
Abbreviations for Processes and Descriptors
Abbreviation	Process or Descriptor
ADD
additive
AL
aluminum
AM
American
ASSOC
association
ATMOS
atmospheric
CALX
catalytic
CEM
continuous emission monitoring
CO
company
COLL
collection
COOP
cooperative
CORP
corporation
DECARB
decarbonization
DESULF
desulfurization
DISTIL
distillation
DISTN
distribution
DIV
division
E
eastern
EA
each
EFF
efficiency
ELECT
electric
EMISS
emissions
ENVIRON OR ENV
environmental
ESP
electrostatic precipitator
FAC
facility
FCC
fluid catalytic cracking
FCCU
fluid catalytic cracking unit
FGR
flue gas recirculation
FURN
furnace
GEN
generator
HAND
handling
HRSG
heat recovery steam generator
HVLP
high-volume, low pressure (spray guns)
i.e.
internal combustion
INCIN
incinerator
INDEP
independent
INTERNAT
international
LAB
laboratory
LDOUT
loadout
D-l

-------
Abbreviation
LIQ
LT
MATL
MFG
MISC
MODIF
NAT
NATL
POLL
PREP
PROD
PWR
REC
RECIP
RECLAM
REFIG
REFIN
REG
REGEN
RESID
ROT
SCR
SCRUB
SECOND
SHIP
SNCR
SOLN
STOR
SUP
SYS
TRANS
UNIV
VAC
VERT
Process or Descriptor
liquid
light
material
manufacturing
miscellaneous
modification
natural
national
pollutant/pollution
preparation
production
power
recovery
reciprocating
reclamation
refrigeration
refinery
regular
regenerator
residual
rotary
selective catalytic reduction
scrubber
secondary
shipping
selective non-catalytic reduction
solution
storage
supplementary
system
transmission
university
vacuum
vertical
D-2

-------
Abbreviations for Emission Limit Units
Abbreviation
Emission Limit Unit
ACF
actual cubic feet
ACFM
actual cubic feet per minute
ACS
applied coating solids
ADP
air dried pulp
AD TP
air dried tons product
ADTFP
air dried tons of final product
ADTUBP
air dried tons of unbleached pulp
ADUP
air dried unbleached pulp
AMP-H
ampere hours
AV
average
BBL
barrels
BF
board feet
BHP
brake horsepower
BLS
black liquor solids
BPSD
barrels per stream day
BTU
British thermal units
CF
cubic feet
CFM
cubic feet per minute
CUYD
cubic yard
D
day
DFEED
dry feed
DACF
dry actual cubic feet
DIST
distillate
DSCF
dry standard cubic feet
F
feet
G
gram
G/B-HP-H
grams per brake horsepower-hour
G/HP-H
grams per horsepower-hour
G/O
gas/oil
GAL
gallon
GAL/M
gallons per minute
GIGA
giga- (l(f prefix)
GR
grains
H
hour
HP
horsepower
J
joule
KG
kilogram
KW
kilowatt
L
liter
LB
pound
LT
long ton
D-3

-------
Abbreviation
M
MI
MIN
MG/L
MM
MO
MW
UG
N
NG
OPAC
PPM
PPH
%
% BY VOL
% BY WT
RDF
RESID
SB
SCF
SCFD
SCFH
SCFM
SEC
SQF
T
T/D
T/H
T/YR
TONNE
VOL
WKS
YD
YR
Emission Limit Unit
thousand (103)
miles
minute
milligram per liter
million (1C?)
month
megawatt
microgram (10"6)
natural
nanogram (10"9)
opacity
parts per million
parts per hundred
percent
% by volume
% by weight
refuse derived fuel
residual
subbituminous
standard cubic feet
standard cubic feet per day
standard cubic feet per hour
standard cubic feet per minute
second
square feet
ton
tons per day
tons per hour
tons per year
metric tonne
volume
weeks
yard
year
D-4

-------
Abbreviations for Pollutants
Abbreviation
Pollutant
AG
silver
AN
acrylonitrile
AR
argon
AS
arsenic
BA
barium
BAP
benzo(a)pyrene
BE
beryllium
CA
calcium
CD
cadmium
CDD
chlorodibenzodioxins
CDF
chl orodib enzofurans
CL
chlorine
CL2
chlorine (gas)
CL2/0CL
chlorine and oxychlorine
CL02
chlorine dioxide
CO
carbon monoxide
C02
carbon dioxide
COS
carbonyl sulfide
CR
chromium
CRVI
hexavalent chrome
CS
cesium
CU
copper
DCB
1,4-dichloro-2-butene
ETH
ethylene
ETO
ethylene oxide
F
fluorine
IF
fluorides, total
FSP
fine suspended particulates
HBR
hydrogen bromide
HC
hydrocarbons
HCL
hydrochloric acid
HCN
hydrogen cyanide
HDM
hexamethylene diisocyanate monomer
HF
hydrogen fluoride
HG
mercury
HHD
homopolymer of HDM (see above)
H20
water
H2S
hydrogen sulfide
H2S04
sulfuric acid
H2S04 mist
sulfuric acid mist (also referred to as SAM)
MA
maleic anhydride
D-5

-------
Abbreviation
MC ACETATE
MEK
MG
MI KETONE
MMH
MN
MO
NAOH
NA2S04
NH3
NH4
NH4CL
NI
NMHC
NMOC
NOX
N02
N20
PAH
PB
PCB
PCDF
PCNB
PM, PM10
POCL3
POHC
RHC
ROC
ROG
RSC
S
SB
SE
SN
502
503
TCDD
TCDF
TCE
TC-ETHANE
TF
TICL4
TMT
Pollutant
methyl cellusolve acetate
methyl ethyl ketone
magnesium
methyl isobutyl ketone
methyl hydrazine
manganese
molybdenum
sodium hydroxide
salt cake
ammonia
ammonium
ammonium chloride
nickel
nonmethane hydrocarbons
nonmethane organic carbon
nitrogen oxide
nitrogen dioxide
nitrous oxide
polynuclear aromatic hydrocarbons
lead
polychlorinated biphenyls
polychlorinated dibenzo furans
pentochloronitrobenzene herbicide
particulate matter
phosphorous oxychloride
principle organic hazardous constituents
reactive hydrocarbons
reactive organic compounds
reactive organic gases
reduced sulfur compounds
sulfur
antimony
selenium
tin
sulfur dioxide
sulfur trioxide
2,3,7,8 -tetrachl orodib enzo-P-di oxin
tetrachlorodibenzo furan
trichl oroethy 1 ene
1,1,1 -trichl oroethane
Total Fluorides
titanium tetrachloride
tetramethyl tin
D-6

-------
Abbreviation
Pollutant
TRS
total reduced sulfur
U
uranium
UF4
uranium tetrafluoride
V
vanadium
vc
vinyl chloride
VCM
vinyl chloride monomer
VE
visible emissions
VOC
volatile organic compounds
ZN
zinc
ZRS04
zirconium sulfate
D-7

-------
Pollutant Name and CAS Number
See also the previous table, Abb
POLLUTANT
1,1,1 TRICHLOROETHANE
2,3,7,8 TCDD
2-BUTANONE
ACETONE
ACRYL AMIDE
ACRYLAMIDE MONOMER
ACRYLIC ACID
ACRYLONITRILE
AG
ALUMINUM OXIDE
AMMONIA
AN
AR
ARGON
AS
ASBESTOS
BA
BAP
BE
BENZENE
BENZO-A-PYRENE
BENZOTRICHLORIDE
BENZYL CHLORIDE
BR
BUTYL ACETATE
BZ
CA
CALCIUM HYDROXIDE
CAPROLACTAM
CARBON BLACK
CARBON TETRACHLORIDE
CCL2F2
CD
CHCL3
CHLORINE
CHLORINE DIOXIDE
CHLOROFORM
CHROME
CHROMIC ACID
tions for Pollutants
ALTERNATE NAME
2,3,7,8 -tetrachl orodib enzo-P-di oxin
Silver
Acrylonitrile
Argon
Arsenic
Barium
Benzo(a)pyrene
Beryllium
Bromine
Benzene
Calcium
Dichlorodifluoromethane
Cadmium
Chloroform
Chromium
D-8
CAS NUMBER
71-55-6
1746-01-6
78-93-3
67-64-1
79-06-1
79-06-1
79-10-7
107-13-1
7440-22-4
1344-28-1
7664-41-7
107-13-1
13994-71-3
13994-71-3
7440-38-2
1332-21-4
7440-39-3
50-32-8
7440-41-7
71-43-2
50-32-8
98-07-7
100-44-7
7726-95-6
123-86-4
71-43-2
7440-70-2
1035-62-0
105-60-2
1333-86-4
56-23-5
75-71-8
7440-43-9
67-66-3
7782-50-5
10049-04-4
67-66-3
7440-47-3
1333-82-0

-------
CL
CL2
CO
C02
COBALT
CR
CR03
CS
CU
DCB
DCB
DIBUTYL PHTHALATE
DIISOBUTYL KETONE
DIMETHYL ACETAMIDE
DIMETHYL FORMAMIDE
DIOXINS
ETHYL ACETATE
ETHYL ALCOHOL
ETHYL BENZENE
ETHYLBENZENE
ETHYLENE GLYCOL
ETHYLENE OXIDE
ETO
F
FLUORIDE
FLUORIDES
FORMALDEHYDE
FREON 12
GRAPHITE
H20
H2S
H2S04
H2S04 MIST
H2S04 VAPORS
HBR
HC
HCL
HCN
HEPTANE
HF
HG
HYDRAZINE
HYDROGEN PEROXIDE
ISOOCTYL ALCOHOL
Chlorine
Chlorine (gas)
Carbon Monoxide
Carbon Dioxide
Chromium
Chromium Trioxide
Cesium
Copper
1,4-dichloro-2-butene
Ethylene Oxide
Fluorine
Water
Hydrogen Sulfide
Sulfuric Acid
Hydrogen Bromide
Hydrochloric Acid
Hydrogen Cyanide
Hydrogen Fluoride
Mercury
7782-50-5
10049-04-4
630-08-0
124-38-9
7440-48-4
7440-47-3
1333-82-0
7440-46-2
7440-50-8
764-41-0
25321-22-6
84-72-2
108-83-8
127-19-5
68-12-2
SEQ. 128
141-78-6
64-17-5
100-41-4
100-41-4
107-21-1
75-21-8
75-21-8
7782-41-4
16984-48-8
16984-48-8
50-00-0
75-71-8
7782-42-5
7732-18-5
7783-06-4
7664-93-9
7664-93-9
7664-93-9
10035-10-6
SEQ. 11
7647-01-0
7490-8
142-82-5
7664-39-3
7439-97-6
302-01-2
7722-84-1
52738-99-5
D-9

-------
ISOPROPYL ACETATE
ISOPROPYL ALCOHOL
MAGNESIUM
MALEIC ANHYDRIDE
MEK
MEK-PEROXIDE
METHACRYLIC ACID
METHANE
METHANOL
METHYL AMYL KETONE
METHYL BROMIDE
METHYL ETHYL KETONE
METHYL ISOBUTYL KETONE
METHYLENE CHORIDE
MG
MINERAL SPIRITS
MMH
MN
MO
N-BUTYL ACETATE
N-BUTYL ALCOHOL
N-PROPYL ACETATE
N20
NAOH
NAPHTHALENE
NH3
NH4
NH4CL
NI
NICKEL
NITRIC ACID
N02
P-TOLUTDINE
PAH
PB
PCB
PERCHLOROETHYLENE
PHENOL
PHOSPHORIC ACID
PHOSPHOROUS
POCL3
POTASSIUM HYDROXIDE
PROPYLENE OXIDE
S
Methyl Ethyl Ketone
Methyl Ethyl Ketone Peroxide
Magnesium
Methyl Hydrazine
Manganese
Molybdenum
Nitrous Oxide
Sodium Hydroxide
Ammonia
Ammonium
Ammonium Chloride
Nickel
Nitrogen Dioxide
Polynuclear Aromatic Hydrocarbons
Lead
Polychlorinated Biphenyls
Phosphorous Oxychloride
Sulfur
94-11-1
67-63-0
7439-95-4
108-31-6
78-93-3
1338-23-4
79-41-4
74-82-8
67-56-1
110-43-0
74-83-9
78-93-3
108-10-1
75-09-2
7439-95-4
64475-85-0
60-34-4
7439-96-5
7439-98-7
123-86-4
71-36-3
109-60-4
10024-97-2
1310-73-2
91-20-3
7664-41-7
14798-03-9
12125-02-5
7440-02-0
7440-02-0
7697-37-2
10102-44-0
106-49-0
SEQ. 6
7439-92-1
1336-36-3
127-18-4
108-95-2
7664-38-2
7723-14-0
10025-87-3
1310-58-3
75-56-9
7704-34-9
D-10

-------
SB
SE
SILVER
SN
502
503
SODIUM BICHROMATE
STRONTIUM CHROMATE
STYRENE
SULFATES
SULFURIC ACID
SULFURIC ACID MIST
TCDD
TICL4
TITANIUM DIOXIDE
TL
TOLUENE
TRICHLOROETHYLENE
TRIETHYL AMINE
U
UF4
URANIUM
V
XYLENE
XYLENES
ZINC
ZINC CHROMATE
ZN
Antimony
Selenium
Tin
Sulfur Dioxide
Sulfur Trioxide
2,3,7,8 -tetrachl orodib enzo-P-di oxin
Titanium Tetrachloride
Thallium
Uranium
Uranium Tetrafluoride
Vanadium
Zinc
7440-36-0
7782-49-2
7440-22-4
7440-31-5
7446-09-5
7446-11-9
10588-01-9
7789-06-2
100-42-5
14808-79-8
7664-93-9
7664-93-9
1746-01-6
7550-45-0
13463-67-7
7440-28-0
108-88-3
79-01-6
121-44-8
7440-61-1
10049-14-6
7440-61-1
7440-62-2
1330-20-7
1330-20-7
7440-66-6
13530-65-9
7440-66-6
Basis for Limit
BACT-PSD	Prevention of Significant Deterioration
BACT-Other	Other (i.e., T-BACT, Toxics-BACT, etc)
LAER	Lowest Available Control Technology
MACT	Maximum Achievable Control Technology
RACT	Reasonably Available Control Technology
GACT	Generally Available Control Technology
NSPS	New Source Performance Standards
NESHAPS	National Emission Standards for Hazardous Air Pollutants
OTHER	Other Control Technology Standards
Emission Type
Point, Fugitive, or Area Source
D-ll

-------
APPENDIX E
RBLC STANDARD EMISSION UNITS BY PROCESS TYPE
CODE

-------
This page has been intentionally left blank.

-------
Appendix E — RBLC Standard Emission Units by Process Type Code
Attached is a list of required emission units to be used when submitting standardized emission
limit information to the RBLC. In general, the emission units of processes not listed here should
be in units related to the production output. Standardization of emission units will facilitate
ranking of emission control requirements on a pollutant specific basis.
Clearinghouse	Required
Process Code / Name or Description
Pollutant
Emission Units
ALL
All Processes with Emission Limits for
Visible
% Opacity

Opacity or Visible Emissions
Emissions

11.001 -
Electric Utility Steam Generators,
PM, PM10,
LB/MMBTU
11.999
Fossil Fuel-fired Steam Generators,
PM2.5, VOC,
(see Note #1)

Boilers, Furnaces, and Process Heaters
SOx, NOx,



CO, Pb

15.001 -
I. C. Engines
NOx, SOx,
G/B-HP-H G/BHP-H
15.999

CO, VOC
(see Note #1)

Stationary Gas Turbines
NOx, SOx,
PPM @ 15% 02


CO, VOC
(see Note #1)
21.001
Municipal Waste Incinerators
Particulate
LB/MMBTU (or



GR/DSCF)


Metals (CD,
GR/DSCF @ 12%C02


PB, HG) and



dioxins/furans



Gas (S02,
PPM @ 12%C02


HCL, CO,
(see Note #1)


NOx)

21.004
Sewage Sludge Incineration
Particulate
LB/T of dry sludge input
30.002
Kraft Pulp Mills - All Sources
HAP
KG/MG


TRS
PPM



(see Note #1)
30.002
Kraft Pulp Mills - Recovery Furnace
Particulate
GR/DSCM @ 8% 02



(see Note #1)

Kraft Pulp Mills - Lime Kiln
Particulate
GR/DSCM @ 10% 02



(see Note #1)

Kraft Pulp Mills - Smelt Dissolving
Particulate
LB/T BLS

Tanks

(see Note #1)
E-l

-------
Clearinghouse
Process Code / Name or Description
Kraft Pulp Mills - Digesters, Brown
Stock Washers, Evaporators,
Oxidation, Stripping System
Pollutant
TRS
41.002
41.004
41.007
41.008
41.011
41.012
41.015
41.018
41.019
41.023
Auto & Light Truck Surface Coating VOC
Can Surface Coating
VOC
Flexible Vinyl & Urethane Coating and VOC
Printing
Large Appliance Surface Coating
Metal Coil Surface Coating
Metal Furniture Surface Coating
Plastic Parts for Business Machines
Surface Coating
Pressure Sensitive Tape & Label
Surface Coating
Printing
50.003	Petroleum Refining - Cracking
50.006	Petroleum Refining - Claus Sulfur
Recovery Units
50.999	Petroleum Refining - Flue Gas
61.009	Phosphate Fertilizers Pdtn.
62.001	Ammonium Sulfate Pdtn.
62.014	Nitric Acid Plants
62.015	Sulfuric Acid Plants
65.001 - Synthetic Fibers Production
65.999
VOC
VOC
VOC
VOC
VOC
VOC
Particulate
SOx
CO
SOx, TRS,
H2S
SOx
Total Fluoride
Particulate
NOX
S02&
Acid Mist
VOC
Required
Emission Units
PPM (by volume) corr to
10% O,
LB/GAL applied coating
solids
LB/GAL applied coating
solids
LB/LB ink solids
LB/GAL of applied
coating solids
LB/GAL applied coating
solids
LB/GAL applied coating
solids
LB/GAL applied coating
solids
LB/LB applied coating
solids
% of total mass of VOC
solvents & H20 used
LB/1000 LB
% by volume
% by volume
GR/DSCF (H2S)
LB/T
(see Note #1)
LB/T ammonium sulfate
pdtn.
LB/T
(see Note #1)
LB/T
(see Note #1)
LB/1000 LB
solvent feed
E-2

-------
Clearinghouse
Process Code / Name or Description
70.007	Grain Elevators
81.003
Ferroalloy Production
81.004
Iron Foundries
81.006 or
Steel Plants - Electric Arc
81.005/81.0

07?

82.001
Lead Acid Battery Mfg.
82.005
Primary Aluminum Pdtn.
82.006
Primary Copper Smelters
82.007
Primary Lead Smelting
82.009
Primary Zinc Smelting
82.011
Sec. Brass & Brass Ingot Pdtn
82.013
Secondary Lead Smelting
Required
Pollutant Emission Units
Particulate GR/DSCF
(see Note #1)
Particulate LB/MW-H 20% (volume
CO	basis)
Particulate GR/DSCF
Particulate GR/DSCF
(see Note #1)
Pb (Lead) GR/DSCF or LB/T
lead feed
Total	LB/T
Fluorides
Particulate GR/DSCF
(see Note #1)
Particulate GR/DSCF
(see Note #1)
Particulate GR/DSCF
(see Note #1)
Particulate GR/DSCF
(see Note #1)
Particulate GR/DSCF
(see Note #1)
90.004
Hot-Mix Asphalt Processing
Particulate
GR/DSCF
90.011
Coal Hand./Proc./Prep./Cleaning
Particulate
GR/DSCF



(see Note #1)
90.016
Glass Mfg. Furnace
Particulate
LB/T



(see Note #1)
90.019
Lime/Limestone
Particulate
LB/T

Handling/Kilns/Storage/Mfg.


90.021
Metallic Mineral/Ore Processing
Particulate
GR/DSCF
90.024
Non-metallic Mineral Processing
Particulate
GR/DSCF
90.026
Phosphate Rock Processing

LB/T
90.028
Portland Cement Plants - kiln, in-line
Particulate
LB/T

raw mil and kiln, clinker cooler

(see Note #1)
90.033
Wool Fiberglass Mfg.
Particulate
LB/T glass pulled
90.034
Asphalt Roofing Products Mfg.
Particulate
LB/1000 LB
E-3

-------
Clearinghouse
Process Code / Name or Description
99.015	Rubber Tire Mfg. Industry - Bead
Pollutant
voc
Required
Emission Units
G/Bead/MO
Cementing Operation
Rubber Tire Mfg. Industry - Tread
End Cementing Operation, Inside
Green Tire Spraying (Water Based),
Outside Green Tire Spraying (Water
Based)
Rubber Tire Mfg. Industry - All Other
Sources
VOC
voc
% Reduction
G/Tire/MO
Note #1:
Standard emission units have been established for these processes. These units are
required for reporting standardized emission limits in the RBLC data base for these
processes.
For all processes, percent % has been established as the unit for reporting standardized
emission limits for opacity and visible emissions (VE).
E-4

-------
TECHNICAL REPORT DATA
(Please read Instructions on the reverse before completing.)
1. REPORT NO.
EPA 456/B-01-001B
2.
3. RECIPIENT'S ACCESSION NO.
4. TITLE AND SUBTITLE
User's Manual for the RACT/BACT/LAER Clearinghouse
(RBLC) Web, Volume 2 - Data Entry
5. REPORT DATE
June 2 0 01
6. PERFORMING ORGANIZATION CODE
7. AUTHOR(S)
Joseph E. Steigerwald
8. PERFORMING ORGANIZATION REPORT NO.
9. PERFORMING ORGANIZATION NAMEAND ADDRESS
Clean Air Technology Center
ITG, ITPID, OAQPS
U.S. EPA
RTP, NC 27711
10. PROGRAM ELEMENT NO.
11. CONTRACT/GRANT NO.
68-D-98-172
12. SPONSORING AGENCY NAME AND ADDRESS
Director, Office of Air Quality Planning and Standards
Office of Air and Radiation
U.S. Environmental Protection Agency
Research Triangle Park, North Carolina 27711
13. TYPE OF REPORT AND PERIOD COVERED
Final
14. SPONSORING AGENCY CODE
EPA/200/04
15. SUPPLEMENTARY NOTES
16. ABSTRACT
The Clean Air Act as amended in 1977 prescribes several techno1ogy-based
limitations affecting new or modified air pollution sources: 1) new source perfor-
mance standards (NSPS), 2) best available control technology (BACT), and 3) lowest
achievable emission rate (LAER) .
The basic purposes of the RACT/BACT/LAER Clearinghouse are 1) to provide State and
local air pollution control agencies with current information on case-by-case control tech-
nology determinations that are made nationwide and 2) promote communication, cooperation,
and sharing of control technology information among the permitting agencies. This document
details how the RBLC site on the World Wide Web is organized and operates. It includes
information on how to do a data base query, generate a custom report, and enter/edit infor-
mation into the RBLC (if authorized) .
The RBLC has now moved to the Web. The RBLC Web address is:
h 11 p://www.epa.gov/11 n/c a t c /
Clicking on the RBLC logo on this page allows access to all of the information in the RBLC
including interactive queries, customized reports, and downloadable copies of this and other
RBLC documents.
Volume 2 includes information for authorized persons in State and local air
permitting agencies who are inputting information directly into the RBLC.
17. KEY WORDS AND DOCUMENT ANALYSIS
a. DESCRIPTORS
b. 1DENTI Fl ERS/OPEN ENDED TERMS
c. COSATI Field Group
Best Available Control Technology
Lowest Achievable Emission Rate
Control Technology Center
New Source Review
Reasonable Achievable Control Technology
Air Pollution
Control

18. DISTRIBUTION STATEMENT
Release Unlimited, Available from NTIS
5285 Port Royal Rd .
Springfield, VA 22161
19. SECURITY CLASS (ThisReport)
Unclassi fied
21. NO. OF PAGES
20. SECURITY CLASS (ThisPage)
Unclassified
22. PRICE
EPA Form 2220-1 (Rev. 4-77) PREVIOUS EDITION IS OBSOLETE

-------