Technical Report
on
Technologically Enhanced
Naturally Occurring Radioactive Materials from
Uranium Mining
Volume 1:
Mining and Reclamation Background
U.S. Environmental Protection Agency
Office of Radiation and Indoor Air
Radiation Protection Division (6608J)
1200 Pennsylvania Avenue
Washington, DC 20460
Previously published on-line and printed as Vol. 1 of EPA 402-R-05-007, January 2006
Updated June 2007 and printed April 2008 as EPA 402-R-08-005

-------
Acknowledgments
This report was prepared by the U.S. EPA, Office of Radiation and Indoor Air, Radiation
Protection Division, Ariel Rios Building, 1200 Pennsylvania Avenue, N.W., Washington, DC
20460. The draft text was distributed for review to the EPA's Regional Radiation program
managers of EPA's Regions I through X. It was also sent to the membership of EPA's National
Hard Rock Mining Team and Abandoned Mine Lands Team, who are employees of the following
EPA offices: U.S. EPA Regions I through X, U.S. EPA Office of Solid Waste and Emergency
Response, U. S. EPA Office of Water, U.S. EPA Office of Compliance and Enforcement, and
U.S. EPA Office of Research and Development. Comments from those reviewers were
incorporated into a revised draft which then underwent peer review and outside review by
external organizations and individuals. EPA would like to thank the following external reviewers:
Dr. Thomas Gesell, Idaho State University, Dr. John Price, Nevada Bureau of Mines and
Geology, and William Chenoweth. EPA is especially appreciative of the comments provided on
the draft by the members of the Interagency Steering Committee on Radiation Standards, NORM
Subcommittee, as well as the U.S. Nuclear Regulatory Commission, Dr. James Otton of the U.S.
Geological Survey, plus the National Mining Association and several of its member companies,
and the Wyoming Mining Association. The comments of all reviewers were carefully considered
and incorporated, wherever possible, throughout the revised report.
The final report and its earlier drafts were prepared with the active participation of the following
EPA employees:
Sanjib Chaki
Elliot Foutes
Shankar Ghose
Brian Littleton
John Mackinney
Daniel Schultheisz
Mark Schuknecht
Loren Setlow
Behram Shroff
Thomas Peake
111

-------
Table of Contents
Executive Summary	ES-1
Chapter 1 Introduction	1-1
Previous EPA Reports	1-3
Origins of Uranium	1-5
Physical Nature of Uranium	1-5
Uses of Uranium in Industry	1-6
Geology and Distribution of Uranium	1-8
Uranium's Contribution to Natural Background Radiation	1-10
Background Gamma Radiation	1-10
Radon in Homes	1-14
Uranium in Water	1-15
Industrial Processes and Activities	1-16
Uranium Associations with Other Metal Mining	1-16
Copper Mining	1-17
Phosphate Production	1-17
Coal Combustion	1-18
Heavy Mineral Sands	1-19
Chapter 2 Uranium Mining and Extraction Processes in the United States	2-1
The Early Years of Uranium Production	2-1
Conventional Uranium Mining Methods	2-4
Open Pit (Surface) Mining	2-5
Underground Mining	2-6
Unconventional Mining Methods	2-8
Heap Leaching	2-8
In Situ Leaching (Solution Mining)	2-9
Uranium Milling	2-11
The Uranium Industry Today	2-12
Chapter 3 Volume and Characteristics of Uranium Mine Wastes	3-1
Waste Footprint of a Mine	3-3
Mine Waste Volumes	3-5
Conventional Open-Pit and Underground Mines	3-5
Waste Volumes at Sample Conventional Mines	3-7
ISL Operations	3-9
Physical Characteristics of Uranium Mine Wastes	3-11
Potential for Water Contamination	3-15
Potential for Soil Contamination	3-19
Hazardous Characteristics of Uranium Mines Waste	3-20
Elevated Radioactivity	3-21
Conventional Mines	3-21
ISL and Heap Leach Operations	3-22
Radon Emanation 	3-23
Elevated Gamma Radiation Exposure Rates 	3-25
Heavy Metals in Mine Wastes	3-25
Uranium Mill Tailings 	3-28
iv

-------
Chapter 4 Uranium Mine and Extraction Facility Reclamation	4-1
Characterizing A Mining Site	4-2
The Reclamation Process	4-4
Overburden and Waste Rock Reclamation	4-5
Heap-Leaching Reclamation	4-6
Mill Tailings Reclamation	4-6
Dry Cover System	4-6
Water-Cover Systems	4-7
Other Approaches	4-7
The Wastewater Problem	4-8
Processes for Treating Uranium Ore	4-8
Water Treatment Techniques	4-9
Lime Treatment	4-9
Ferric Chloride Treatment	4-10
Barium Chloride Treatment	4-10
Ion Exchange and adsorption	4-10
Bioremediation	4-10
Permeable Reactive Barriers	4-11
Wastewater Preventive Strategies	4-11
Underground Mines	4-11
Surface impoundments of Mine Waste Materials 	4-11
Open Pits	4-12
Ground-Water Protection at ISL Sites	4-12
Building and Equipment Reclamation	4-13
Radiation Protection Standards for Reclaiming and Remediating
Uranium Mines and extraction Facilities	4-13
Costs of Reclaiming & Remediating Uranium Mines & Extraction Facilities	4-15
Stewardship and Long Term Monitoring, Management and Remediation	4-19
Chapter 5 Conclusion	5-1
Chapter 6 Bibliography	6-1
Appendix I List of Acronyms and Abbreviations, and Glossary of Terms	Al-1
Appendix II Uranium Decay Series	AII-1
Appendix III Overview of Uranium Mines and In Situ Leach Operation
Case Studies	AIII-1
Appendix IV Calculations of Volumes of Uranium Overburden and
Waste Rock	AIV-1
Appendix V Radiochemical Data for Uranium Overburden and Waste Rock,
Pit Lakes and Streams, and/« Situ Leach Operation	AV-1
Appendix VI Legal Authorities Concerning Uranium, Uranium Mines and
Extraction Facilities	AV1-1
v

-------
Tables
1.1	Percentage of Natural Abundance and Half-Lives of Uranium Isotopes
by Total Weight	1-6
1.2	Multiple Industrial Uses of Uranium	1-7
1.3	Concentrations of Certain Natural Radionuclides in Igneous and
Sedimentary Rocks	1-12
1.4	Absorbed Dose Rate in Air from Terrestrial Radiation Sources	1-13
1.5	Average Annual Human Exposure to Radiation	1-14
1.6	Mineral Commodities with Uranium Associations	1-17
1.7	Radionuclide Concentrations in Process & Waste Samples	1-20
2.1	Major U.S. Uranium Mining Districts	2-2
2.2	U.S. Uranium Mine Production 2000-2005 	2-14
2.3	Uranium Reserves of the United States as of
December 31, 2003	2-17
3.1	Uranium Mine and Operations Wastes	3-2
3.2	Profile of Several Texas ISL Uranium Mining Operations	3-5
3.3	Estimated Overburden Produced by Open-Pit and Underground Mining	3-7
3.4	Changing Ratio of Overburden to Ore Over Mine Life-Jackpile-Paguate
Mine, New Mexico	3-8
3.5	Mine Workings and Associated Waste Rock Volumes in
Canyonlands, Utah	3-8
3.6	Examples of Waste Rock Types Found at Uranium Mines in Selected
States	3-12
3.7	Overburden Particle Size Distributions, Pennsylvania Mine	3-12
3.8	White King/Lucky Lass Mine Protore and overburden Characteristics	3-13
3.9	Radon Flux from Selected Uranium Mine Wastes	3-24
3.10	Metals Sampling Data from Uranium Mines in New Mexico
and Wyoming	3-26
3.11	Radionuclides and Metals from Protore and Overburden, Yazzie 312
Mine, Arizona	3-27
3.12	Metals in Canyonlands National Park Mine Waste piles	3-28
3.13	Typical Characteristics of Uranium Mill Tailings	3-30
4.1	Total and Average Production and Costs of Remediation of Title I
Uranium Mills and Related Facilities	4-16
4.2	Total and Average Production and Costs of Remediation of Title II
Uranium Mills and Related Facilities	4-17
4.3	Total and Average Production and Costs of Reclamation of All
Mill Uranium Mill Sites (Title I and Title II)	4-17
4.4	Total and Average Production and Costs of Reclamation of
All Uranium Mines	4-18
vi

-------
Figures
1.1	U.S. Geographic Areas Rich in Uranium	1-11
1.2	Gamma Ray Radiation Across the United States	1-13
1.3	Average Indoor-Air, Screening-Level Concentrations of Radon in
the United States	1-15
2.1	Mines and Other Location with Uranium in the Western U.S	2-3
2.2	Surface mine Showing Drag Line and Overburden	2-5
2.3	Surface Mine	2.6
2.4	Diagram of Room and Pillar Underground Mining	2-7
2.5	Illustration of Heap Leaching Process	2-9
2.6	Illustration of ISL Process	2-10
2.7	Generalized Uranium Mill Physical Layout	2-12
2.8	Major U.S. Uranium Reserve Areas	2-16
2.9	Status of Mines ISL Operations, and Mills in the U.S. as of
November 2005	2-18
3.1	Mine Portal, Cayonlands National Park, Utah	3-9
3.2	ISL Operation Drilling Site	3-10
3.3	ISL Evaporation Pond	3-11
3.4a Overburden Pile at Yazzie-312 Open Pit Mine, Navajo Reservation,
Arizona	3-14
3.4b Pit Lake at Yazzi-312 Open Pit Mine, Navajo Reservation, Arizona	3-14
3.5	Average Annual Precipitation in the Western United States	3-16
3.6	Surficial Aquifers of the Colorado Plateau	3-17
vii

-------
Executive Summary
This report, the first of two volumes, examines the occurrence of uranium in its natural settings in
the United States, its industrial uses, and the methods employed over the last century to extract it from ore
deposits. In addition, the report explores the nature of solid and liquid wastes generated by the extraction
methods, and the various reclamation and remediation methods which can environmentally restore the
extraction site. A second volume, to be issued separately, will examine, in a general way, the potential
radiogenic cancer risks from abandoned uranium mines, as well as environmental and geographical issues
associated with those mines. The intent of that report will be to generally identify who is most likely to be
exposed to uranium, and where the greatest risks may be found. U.S. Environmental Protection Agency
(EPA) field studies are used in both reports, providing examples of current conditions of abandoned and
remediated mines. A related report compiles information from multiple sources providing locations
throughout the United States, though concentrating on sites of the western U.S., that have been explored
or mined for uranium.
In this report, Naturally Occurring Radioactive Material (NORM) is defined as: Materials which
may contain any of the primordial radionuclides or radioactive elements as they occur in nature,
such as radium, uranium, thorium, potassium, and their radioactive decay products, that are
undisturbed as a result of human activities. The term Technologically Enhanced Naturally Occurring
Radioactive Material (TENORM) is defined as: Naturally occurring radioactive materials that have
been concentrated or exposed to the accessible environment as a result of human activities such as
manufacturing, mineral extraction, or water processing. Technologically enhanced means that
the radiological, physical, and chemical properties of the radioactive material have been altered by having
been processed, or beneficiated, or disturbed in a way that increases the potential for human and/or
environmental exposures.
EPA's Radiation Protection Division decided that a further review of the current hazards
associated with uranium mining TENORM was warranted following a review of EPA's guidance for
TENORM by the National Academy of Sciences (NAS), EPA's response to the NAS study, and
discussions with EPA's Science Advisory Board (SAB). The SAB agreed with EPA's intent to make
TENORM documents useful to a broad audience, but also recommended that the whole life cycle of a
TENORM source, in this case uranium extraction, be considered beyond regulatory or inter-agency
considerations, and that the impacts of non-radiological contaminants also be examined.
In addition to most sources of TENORM, EPA has authority for environmental standard setting
under the Uranium Mill Tailings Radiation Control Act, cleanup of hazardous waste sites which currently
include some former uranium mines, and assistance to Native Americans that has also included
environmental reviews of proposed in situ leaching (ISL) facilities. This document will provide limited
background materials on uranium milling and ISL operations and waste generated by those processes,
even though they are considered to be byproduct materials, not TENORM, under the Atomic Energy Act
and its amendments. Information will also be provided on the regulatory agencies responsible for
oversight of those operations.
Uranium mills and mill tailings impoundments are regulated by the NRC or its Agreement States.
Many of the physical and chemical processes used at uranium mills are the same as those which extract
uranium at ISL operations. While the tailings are not legally considered TENORM in the United States,
this phase of the uranium fuel cycle is described in the report, in part, because radiation protection
standards for the tailings impoundments may have applicability to waste disposal for uranium mine
TENORM wastes. Additionally, the NRC has decided to allow mill operators to dispose of wastes other
ES-1

-------
than tailings in the impoundments. This may be a possible disposal route for some currently unreclaimed
conventional uranium mine TENORM.
Uranium in ores can be extracted and chemically converted into uranium oxide (U308) or other
chemical forms usable in industry. Uranium-238 undergoes radioactive decay into a long series of 13
different radionuclides before finally reaching a stable state in lead-206. These radionuclides each emit
alpha or beta radiation and some also emit gamma radiation. Some of these progeny radionuclides are
highly radioactive and can pose significant human health risks. One of those radionuclides in the series is
actually a radioactive gas, radon-222. The most significant applications of uranium have been for nuclear
weapons production and electric power generation. Concurrent with these efforts to develop weapons and
harness atomic energy for electricity, the surging demands for uranium led to an exploration and mining
boom for the mineral commencing in the late 1940s and ending in the 1980s, with a continuing decline
until about 2004. An increase in all aspects of the industry since then included drilling, mining,
production and employment.
Most uranium mining in the United States has taken place in the Colorado Plateau region
including the states of Utah, Colorado, New Mexico, and Arizona, though more than a dozen states have
hosted uranium mining operations. Some mines were focused on extraction of just uranium minerals,
whereas many other mines produced uranium along with other valuable minerals found together in the
same ore.
Mining is the mechanical process by which mineral ores are extracted from the earth. The term
ore implies economic viability in which the value of the metal extracted from the host rock is worth more
than the total costs of extraction and site restoration. Protore is mined uranium ore that is not rich enough
to meet the market demand and price. This subeconomic ore is often stockpiled at the mine site for future
exploitation under the appropriate economic or market demand conditions. A significant waste material
that is classified as TENORM from uranium mining is overburden. Overburden overlies the uranium ore
body, but is not necessarily enriched in uranium as is protore. Other mine wastes which could be
classified as TENORM include unreclaimed subeconomic ores (protore), waste rock (which is rock void
of uranium ore which may have been set aside as waste after removal of top-soil, overburden and uranium
ore or veins), drill core and cuttings, and mine and pit (or pit lake) water.
Early mining methods for uranium used what are termed conventional methods: open-pit mining
is employed for ore deposits that are located at or near the surface, while underground mining is used to
extract ore from deeper deposits. The early small mining endeavors generated small quantities of waste
typically discarded within a few feet to hundreds of feet (100 meters or more) of the mine opening or pit.
Generally, tens to hundreds of acres (or hectares) may be covered by overburden and waste rock at
surface mining sites. This study found that the surface area affected by major underground mining
activities generally involves less than about 50 acres (20 hectares).
The volume of waste produced by surface, open-pit mining is a factor of approximately 45 greater
than from underground mining, based on their respective averages. Thus, the amount of overburden
generated from open-pit mines far exceeds that of underground mines. The U.S. Geological Survey
estimated that the total amount of waste rock generated by the approximately 4,000 operating
conventional mines in their data files is between one billion and nine billion metric tons of waste, with a
likely estimate of three billion metric tons. The characteristics of overburden and waste rock from
conventional mines depend on the geology of the zone where the ore was originally mined, and how the
waste was subsequently treated. Overburden and waste rock can include huge boulders that may have
been broken down with explosives and heavy machinery into particles as small as clay size.
ES-2

-------
Increased use of ISL as an "unconventional", though now relatively common, mining method,
has significantly reduced the volume of solid waste generated (regulated by the NRC or its Agreement
States). The solid waste from ISL consists of: (1) soil and weathered bedrock material, (2) waste from
drilling of injection and production wells, and (3) solids precipitated during storage and processing of
fluids in holding ponds. The total areal extent of an ISL operation may be large, covering from 200 to
more than 6,000 acres (81 to 2,430 hectares), depending on how drill holes are situated, and how
extensive evaporation ponds are, though the facilities themselves may take up only a small part of the
total acreage. Available data are insufficient to estimate the total amount of solid and liquid wastes
generated by existing and previous ISL operations.
Radiation and hazardous materials studies from mine reclamation assessments indicate that
material identified as "waste" or "overburden" varies widely in radium-226 activity, but that for most
waste piles dominated by overburden material, measurements higher than 20 pCi/g (0.74 Bq/g) are
unusual. Protore, on the other hand, can be considerably higher in radium-226 activity, with most material
in the range of 30-600 pCi/g (about 1-22 Bq/g). As a point of comparison, information on radionuclides
present in ISL operation wastewater ponds is very limited. Liquid wastes from those operations have
some residual uranium and radium-226 activities that range from background levels (<2 pCi/L) to
concentrations as high as 3,000 pCi/L (111 Bq/L). Solid wastes from ISL operations can have several
hundred ppm uranium and 300-3,000 pCi/g radium-226 (about 11-111 Bq/g).
Radon measurements in some abandoned underground mines where mechanical ventilation has
ceased are quite high, and pose risks for prolonged human exposure by members of the public visiting for
recreation, exploration of old workings for geologic purposes, or reclamation workers. As an example,
radon readings by alpha track canisters installed at underground mine portals of the Ross Adams uranium
mine in Alaska measured from 212 pCi/L to 540 pCi/L (about 8 to 20 Bq/L). Radon emanation
coefficients (the fraction of radon atoms present in a material that emanate into rock or sediment pore
space) for sandstone and other uranium ores are extremely variable. Coefficients vary with: (1) uranium
mineralogy; (2) radium mineralogy; (3) host rock lithology; (4) grain size of uranium/radium minerals;
(5) comminution, or fineness, of the ore; (6) estimated porosity and permeability of the ore; (7) moisture
content; and (8) ore grade. Unlike barren or low-activity waste rock, waste rock and protore piles with
elevated activity not only form more radon, but in many districts they release a great deal of that radon to
pore spaces, and the radon is free to migrate.
Radon flux rates from overburden are difficult to characterize because of the rock's diverse
physical forms and matrices, and diverse emplacement and disposal methods. Field measurements
indicate that average radon flux rates vary from about 2-60 pCi/m2s (about 0.07-2 Bq/m2s) for
overburden materials to as high as a few hundred pCi/m2s (> about 7 Bq/m2s) for low-grade ore materials.
The broad range of radon flux rates is due, in part, to varying radium concentrations (the parent
radionuclide) found in protore that is at times disposed of with overburden. Radon flux rates much higher
than these wastes have been reported for undisturbed natural rock outcrops adjacent to uranium extraction
operations.
Elevated gamma radiation is always found at uranium mine sites. The primary contributors to
gamma exposure are the decay products of radium; the higher the radium present, the higher the ultimate
gamma exposure rate. Radium content is also roughly proportional to uranium content in raw mine
materials. Exposure rates associated with ambient background levels range from 10 to 85 (j,R/hr,
averaging about 20 (j,R/hr including background. Protore exposure rates range from 80 to 1,250 }iR/hr,
with an average value estimated at 350 }iR/hr.
ES-3

-------
A number of heavy metals may occur in association with uranium deposits and wastes from
uranium mining. Heavy metals on site, particularly arsenic, can be of concern, and can pose serious risks
if they migrate to groundwater. Depending on local geology and climate, the presence and eventual
leaching or remobilization of these metals could lead to contamination of surrounding lands and water
bodies. Waters affected by uranium mining may be on, adjacent to, or at some distance from a mine or
mines. Uranium and thorium, and radium to a lesser extent, can be mobilized by either acidic or alkaline
solutions. Pyrite and other sulfur-bearing minerals are key determinants as to whether acid mine drainage
occurs. Most of the mines located in the sedimentary sandstone deposits of the southwestern United States
are not in pyritic formations (with the exception of ores in South Texas, where pyrite and its
pseudomorph, marcasite, are common), and the resulting runoff waters or pit lakes are generally neutral to
alkaline in character (pH of 7 or higher). However, this contrasts with the measurements made at mine
locations in the Pacific Northwest—areas with higher-than-average rainfall amounts and metamorphic
and igneous rocks, including sulfur-bearing minerals that could transform runoff into acidic waters
(pH < 7).
Mining reclamation is the act of returning a mine to a long-term stable condition, or its original
contour, to ensure the safe reuse of the site by both current and future generations. When possible, a
reclamation plan aims to return the affected areas to previously existing environmental conditions.
Differing views as to what is an acceptable environmental condition for reclaimed mining sites explain
the varying regulatory requirements for uranium mining sites. The existence of bonding requirements
and/or financial guarantees in the cases where private parties are involved in the mine may also play an
important role in determining the extent of reclamation. Extraction facilities licensed by the NRC or its
Agreement States are required to have bonds sufficient to allow a third party to reclaim the property
should the company holding the site fail. Additionally, regulatory requirements affect selected
reclamation techniques, as some techniques may be adequate to meet less stringent requirements, but will
not be suitable for more restrictive requirements. In some cases, the remoteness and aridity of a site and
reduced risk for human exposure may affect decisions on whether a site is in need of reclamation, or the
extent to which it is reclaimed, if at all.
Many site factors can influence the reclamation of a mining site, including topography, geology,
hydrology, hydrogeochemistry, climatology, ecology, operating characteristics, radiological
characteristics, and socioeconomic characteristics. For example, the topographical setting (whether the
site is located in a valley or on a hillside) can affect a site's hydrology and climate. Knowledge of a site's
climatology, hydrology, and hydrogeochemistry is needed for assessing its impacts on water bodies in the
area. In turn, these impacts may influence decisions on strategies and techniques for reclamation.
A site's operational and radiological characteristics are of prime importance in its reclamation.
The historical type of mining, mine layout, and extraction methods will affect the location and types of
wastes present, and knowledge of how the mine operated can improve reclamation procedures utilized.
Geotechnical aspects of the mine, including its stability, will help determine if certain reclamation options
will endanger the workers, while radiological and chemical characteristics determine how much
reclamation must be conducted. Off site characterization is extremely important too, as both natural and
human factors may have resulted in dispersion of dusts, rock, liquid, refuse or other wastes contaminated
with radionuclides or other pollutants beyond the borders of a mine or its related facilities. Transport of
ore and waste rock to other locations away from a mine are not uncommon. In this regard, reconnaissance
walking, aerial, and radiation surveying may provide initial evidence of the need for more detailed
evaluations. Sampling of water and soils off site may also provide evidence of contaminant releases.
ES-4

-------
Treatment of contaminated mine wastewater is usually required, with release concentrations of
specific contaminants dictated by federal and state requirements. While many treatment technologies are
capable of achieving concentrations that are well below regulatory requirements, the accumulation of
contaminants in the sediments may also need to be taken into account. Traditionally, large volumes of
contaminated water being pumped or released from a site (greater than 1,500 ft3/hr (42.5 m3/hr)) are
usually treated by some form of chemical process, though it may also be treated by newer technologies,
such as biological treatment in wetlands, evaporation ponds, and reactive barriers. The residues and
sludges from the treatment must be disposed of as determined by the state, federal, or Tribal land
management agency. This can occur either on-site or at an engineered low-level radioactive waste
disposal cell, or an approved off-site disposal area. In some cases, depending on the quality of remediated
water, standing bodies of water may be left behind permanently.
EPA groundwater protection standards issued under authority of UMTRCA are required to be
followed by ISL licensees of the NRC or its Agreement States. Remediation of groundwater in the
wellfield must be conducted to return the groundwater and other systems to as close to pre-extraction
conditions, or EPA drinking water maximum contaminant limit levels where possible or practical. If that
is not possible, alternate concentration limits (ACL's) in terms of the presence of metals, organics, pH
level, and radioactivity, may be approved by the NRC or its Agreement States, with EPA concurrence. In
addition to those requirements, ISL operators also must comply with EPA Underground Injection Control
regulations. Groundwater restoration is accomplished through a strategy called pump and treat. After an
ISL wellfield is exhausted, the aquifer must be restored. During aquifer restoration operations, relatively
large volumes of wastewater are generated. Waste disposal systems at ISL operations usually consist of a
combination of evaporation ponds, deep-well injection, and surface discharge (usually via irrigation).
Evaporation ponds must be double lined and must incorporate leak-detection and collection systems.
Pond residues must be shipped off site to approved disposal facilities. Regulations prohibit the injection
of ISL waste into aquifers containing less than 10,000 ppm of total dissolved solids. A variety of aquifer
restoration processes have been used in the United States. Remediation generally follows five stages: (1)
groundwater sweep, (2) water treatment, (3) reductant addition, (4) circulation, and (5) stabilization.
Reviews are provided in Chapter 4 of the report of the principal methods of reclaiming open-pit
and uranium mines, including means of remediating releases of radionuclides, metals, or other hazardous
materials on, and off-site. A discussion is also provided of the principal regulatory and other guidances
issued by EPA, the NRC, and DOE for managing radiation at uranium mills and their tailings
impoundments, closure of uranium extraction facilities, cleanup of radioactively contaminated soils, and
protection and cleanup of groundwater sources from contamination from uranium mines and extraction
facilities.
Data from a Department of Energy/Energy Information Administration study reveal that the costs
of reclamation without site monitoring for 21 mines ranged from a low of $2,337/hectare of disturbance
to a high of $269,531/hectare of disturbance. The average total estimated cost is $13.9 million per mine.
Many smaller mines less than 25 acres (10 hectares), which may constitute the majority of currently
unreclaimed mine-scarred lands, especially in arid regions, may require remediation costs on the order of
$45,000 or less. This cost would be incurred to bury waste piles back in a pit or underground mine
opening, clean up the soil to lower radionuclide and metal levels, and close or armor the mine opening
with rock. Remediation actions under CERCLA for spilled ore off-site of a mine can be expensive. U.S.
DOE/EIA in 1995 estimated average decommissioning costs for ISL operations were an estimated $7
million. On the other hand, cleanup in 2005 of 12 sites where ore had spilled off of ore trucks on the haul
road between the Midnite Mine and the Dawn Mill in Washington state, some 18 miles distant, amounted
to a cost of approximately $357,500.
ES-5

-------
When mining or extraction facilities are closed, stewardship and monitoring may or may not be
required to ensure that remediation goals have been met. This requirement depends on statutory
requirements for federal, state or Tribal agencies, the nature of the site, and local site conditions. For
example, after the stabilization monitoring phase at NRC or Agreement State licensed/permitted ISL
facilities, if there is no indication of increasing levels of groundwater constituents of concern, the site is
released for unrestricted use. Conversely, mines remediated under EPA Superfund oversight, can require
open ended periodic monitoring until it is similarly determined that the site can be released. Many mines
on federal, state, and Tribal lands in the western U.S. have been considered closed without need for
further monitoring once they have been reclaimed (or remediated if necessary). Uranium mill tailings sites
under UMTRCA requirements once reclaimed are licensed to the DOE and designed for 1,000 years of
control.
Overall, this report provides technical information on uranium mining, the associated TENORM
wastes, and impacts from production. In addition, information is presented on reclamation and
remediation considerations and technology used to facilitate the appropriate management of radiation and
waste materials at both uranium mines, and uranium extraction facilities.
ES-6

-------
Chapter 1. Introduction
Uranium is a common element in nature that has for centuries been used as a coloring agent in
decorative glass and ceramics. Uranium and its radioactive decay products are ubiquitous in
nature, and contribute to natural background radiation found everywhere. In fact, it is important
to note that many of the natural occurrences of uranium present radiation hazards without any
disturbance from miners. By far, the greatest uses of uranium have been defense and electric
power generation. The advent of nuclear weapons and nuclear power in the United States resulted
in a full-blown exploration and mining boom starting immediately after World War II, making
uranium the most important commodity in the mining industry. The uranium production peak
spanned from approximately 1948 to the early 1980s (U.S. DOE/EIA 1992). Some uranium
mining continues in the United States, and relatively high-grade resources in other parts of the
world are being mined to meet continued demand. Through the first half of 2005 the industry had
generated over 358,000 metric tons (MTs) of uranium (U3Os) to foster U.S. dominance in nuclear
weapons technology, and later to feed the growing number of commercial power plants that
utilized the enormous energy contained in the uranium nucleus.1
Another legacy of uranium exploration, mining, and ore processing were many unreclaimed land
workings left behind where the uranium concentration in rock was either found or thought to be
economically recoverable. Thousands of miners and prospectors, as well as large mining
companies, searched the United States for mineral deposits concentrating the valuable metal,
echoing the California gold rush 100 years earlier. In many instances before the 1970s, they left
behind unreclaimed and exposed wastes elevated in radioactivity from uranium and its
radioactive decay progeny, potentially exposing people and the environment to its hazards.
In this report, Naturally Occurring Radioactive Material (NORM) is defined as: Materials which
may contain any of the primordial radionuclides or radioactive elements as they occur in
nature, such as radium, uranium, thorium, potassium, and their radioactive decay
products, that are undisturbed as a result of human activities. Radiation levels presented by
NORM are generally referred to as a component of "natural background radiation".
The term Technologically Enhanced Naturally Occurring Radioactive Material (TENORM)
is defined as: Naturally occurring radioactive materials that have been concentrated or
exposed to the accessible environment as a result of human activities such as
manufacturing, mineral extraction, or water processing. "Technologically enhanced"
means that the radiological, physical, and chemical properties of the radioactive material have
been altered by having been processed, or beneficiated, or disturbed in a way that increases the
potential for human and/or environmental exposures. This definition differs somewhat from other
definitions provided by the National Academy of Sciences (1999a) and the Conference of
Radiation Control Protection Directors (CRCPD 2004) in that it further amplifies the need to
include materials which have not been modified by human activities, yet have been disturbed in
such ways that they can be misused by humans, or affect the environment2; it does not include a
1	Data compiled from U.S. DOE/EIA 2003a, 2003b, 2005b.
2
The National Academy of Sciences (1999a) defined TENORM as "...any naturally occurring radioactive
materials not subject to regulation under the Atomic Energy Act whose radionuclide concentrations or
potential for human exposure have been increased above levels encountered in the natural state by human
activities." The International Atomic Energy Agency (2003), although referring to this class of wastes
and products as "NORMs", defined them as encompassing "all naturally occurring radioactive materials
where human activities have increased the potential for exposure in comparison with the unaltered
1-1

-------
reference to Atomic Energy Act materials as the definitions are changing (see further below and
Appendix VI).
Under the Atomic Energy Act, the U.S. Nuclear Regulatory Commission (NRC) regulates
operations which produce and concentrate uranium and thorium. In accordance with terminology
of the Act, the NRC has defined in 10 CFR 40.4 "source materials" as (1) uranium or thorium,
or any combination thereof, in any physical or chemical form or (2) ores which contain by
weight one-twentieth of one percent (0.05%) or more of: (i) uranium, (ii) thorium or (iii)
any combination thereof. Source material does not include special nuclear material. It also
defines the "by-product materials" (wastes) of those operations as tailings or wastes produced
by the extraction or concentration of uranium or thorium from any ore processed primarily
for its source material content, including discrete surface wastes resulting from uranium
solution extraction processes. Underground ore bodies depleted by such solution extraction
operations do not constitute "byproduct material" within this definition. Byproduct materials
are also regulated by the NRC.
However, certain types of waste from conventional mining of uranium (surface and underground
mining) are not subject to NRC regulation, and are considered to be TENORM. Thus, while this
report includes information about uranium extraction, processing methods and wastes, only the
wastes from conventional mining are considered to be TENORM, and subject to U.S.
Environmental Protection Agency (EPA) and State agency oversight. Those distinctions will be
made clear below, and elsewhere in this report.
Under the Energy Policy Act of 2005, the Atomic Energy Act was amended to place additional
discrete (highly radioactive in small quantities) sources of TENORM under NRC jurisdiction
which had the potential for use in a radioactive weapon. The definition of byproduct materials
was further modified to include discrete sources of radium-226, any material made radioactive by
use of a particle accelerator for use for a commercial, medical or research activity, or materials
which might pose a similar threat if used to make a radioactive weapon. Specific requirements
were provided for determining the appropriate waste disposal methods for these materials. The
NRC regulatory definitions of byproduct materials to accommodate these amendments have not
been revised to reflect the recent amendments as of this writing. While these products and wastes
are not the subject of this report, further discussion on these changes to the Atomic Energy Act
are included in Appendix VI.
Other important acronyms and definitions of key terms in this report can be found in Appendix I.
situation. Concentrations of radionuclides (i.e. TENORM) may or may not have been increased."
Alternatively, the Conference of Radiation Control Program Directors (CRCPD 2004) has defined them
as a naturally occurring radioactive material whose radionuclide concentrations are increased by or as a
result of past or present human practices. TENORM does not include background radiation or the natural
radioactivity of rocks or soils. TENORM does not include "source material" or "byproduct material" as
both are defined in the Atomic Energy Act of 1954, as amended (AEA 42 USC §2011 el seq.) and
relevant regulations implemented by the NRC. EPA believes the definition should include materials
which were disturbed, but not further concentrated by human activities; by not including this slightly
broader definition, not only a significant amount of radioactive waste, but nearly all products which
include TENORM would be exempted from regulation.
1-2

-------
Previous EPA Reports
The U.S. Environmental Protection Agency has previously issued reports on the uranium mining
industry in response to congressional mandates and programmatic needs. In 1983, EPA published
its Report to Congress on the Potential Health and Environmental Hazards of Uranium Mine
Wastes (U.S. EPA 1983 a, b, c), as required by the Uranium Mill Tailings Radiation Control Act
of 1978. This study provided an important overview of the characteristics and generation of
uranium mining TENORM wastes during a period when the uranium mining industry was still
near its production peak. A subsequent 1985 Report to Congress on Wastes from the Extraction
and Beneficiation of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium
Mining, and Oil Shale (U.S. EPA 1985), carried out pursuant to requirements of the Resource
Conservation and Recovery Act of 1976 (RCRA), as amended, provided additional risk
information and characterization of uranium mining waste. In 1995, EPA issued the Technical
Resource Document: Extraction and Beneficiation of Ores and Minerals: Uranium as a technical
update to provide a means of evaluating wastes that were exempt from or subject to regulation
under RCRA (U.S. EPA 1995a).
During the period 1989 to 1993, EPA worked on a draft scoping report (SC&A 1993), now out of
print, which compiled information on TENORM in several industries, including uranium mining.
A preliminary risk assessment was also developed for certain public and occupational exposure
scenarios to the known radiation levels in those industries. Comments received on the draft from
industry, as well as EPA's Science Advisory Board (U.S. EPA 1994), resulted in further revisions
of the scoping draft, though it was ultimately decided that a final report would not be issued.
Following a review of EPA's guidance for TENORM by the National Academy of Sciences
(NAS 1999a), EPA's response to the NAS study (U.S. EPA 2000b), and discussions with EPA's
Science Advisory Board (SAB), EPA's Radiation Protection Division decided that a further
review of the current hazards associated with uranium mining TENORM was warranted.
The SAB (U.S. EPA 2001d) agreed with EPA's intent to make TENORM documents useful to a
broad audience, but also recommended that the whole life cycle of a TENORM source, in this
case uranium extraction, be considered beyond regulatory or inter-agency considerations, and that
the impacts of non-radiological contaminants also be examined in the Agency's technical reports.
In addition to most sources of TENORM, EPA has authorities for environmental standard setting
under the Uranium Mill Tailings Radiation Control Act, cleanup of hazardous waste sites which
currently include some former uranium mines, and assistance to Native Americans that has
included assistance in environmental reviews of proposed in situ leach (ISL) facilities. This report
will provide limited background materials on uranium milling and ISL operations and waste
generated by those processes, even though they may not be considered TENORM by virtue of
their regulation under the Atomic Energy Act and its amendments; information will also be
provided on the regulatory agencies responsible for oversight of those operations.
Uranium mills and mill tailings impoundments are regulated by the NRC or its Agreement States.
Many of the physical and chemical processes used at uranium mills are the same as those which
extract uranium at ISL operations. While the tailings are not legally considered TENORM in the
United States, this phase of the uranium fuel cycle is described in the report in part because
radiation protection standards for the tailings impoundments may have applicability to waste
disposal for uranium mine TENORM wastes. Additionally, the NRC has decided to allow mill
operators to dispose of wastes other than tailings in the impoundments, which is a possible
disposal route for some currently unreclaimed conventional uranium mine TENORM.
1-3

-------
This report is the first of two volumes on uranium mining TENORM. It provides background
information on the occurrence, mining, and reclamation of uranium mines and mills. Chapter 1
examines the occurrence of uranium in nature, its uses, and its contribution to background
radiation in the United States. Chapter 2 provides an overview of mining and milling methods
used to extract uranium from its host rocks, while Chapter 3 provides an evaluation of the volume
and characteristics of uranium mining TENORM wastes in the United States. Chapter 4 provides
a process-oriented review of reclamation3 and remediation4 techniques and goals to clean up
uranium mines and extraction facilities to reduce their hazards to the environment, while Chapter
5 summarizes the key information developed in the report. The second volume entitled
Technologically Enhanced Naturally Occurring Radioactive Materials (TENORM) from Uranium
Mining: Volume II: Investigation of Potential Health, Geographic, and Environmental Issues of
Abandoned Uranium Mines (2006a), will evaluate, in a general way, potential radiogenic cancer
and environmental risks posed by abandoned uranium mines. A technical report entitled Uranium
Location Database (EPA 2006b) in concert with these volumes will provide information on an
EPA generated digital spatial database on mines with uranium, and mill locations.
Information on uranium mining waste characteristics for this report has been obtained from
several sources, including industries, EPA contractors, federal, state, and Tribal agencies, and
scientific literature published by various national and international organizations. EPA's own
field studies on a number of uranium mining sites around the United States, several of which are
described in the case studies of the Appendix, have contributed to a better understanding of the
physical, geographic, and chemical aspects of these wastes. The draft of this report underwent an
outside peer review following the Agency's peer review process, and was provided to member
agencies of the Interagency Steering Committee on Radiation Standards (ISCORS) Subcommittee
on NORM, as well as other selected knowledgeable individuals and organizations, for comment.
Based on reviewers' comments received on the draft reports as well as meetings with
stakeholders, the Agency will make a determination on what further steps may be necessary for
the purpose of radiation protection from this source of waste material. The specific wastes of EPA
concern from this report and study are from conventional open-pit and underground uranium
mines, and include overburden, unreclaimed subeconomic ores (protore), waste rock5, core hole
and drill cuttings, mine and pit (or pit lake) water.
As a result of the review comments, significant new information was added to the report on
uranium geochemistry and radionuclide environmental transport, as well as on uranium mine,
ISL, and mill tailings reclamation methods and requirements. Waste and mining terminology was
made more consistent across the report, more definitions of geological, mining, and radiological
terms were provided and also included as a glossary in Appendix I, the report tone was changed,
and several new references and figures were added. New text was added to this chapter (see
above) to clarify the reasons information is included in this report on ISL and milling operations,
even though they are for the most part overseen by agencies other than EPA. Responding to
3	Reclamation is the restoration of mined land to its original contour, use or condition.
4	Remediation is the cleanup or other methods used to remove or contain a toxic spill or hazardous
materials from a Superfund site or uranium mine or extraction facility, including those included under the
Uranium Mill Tailings Radiation Control Act (UMTRCA).
5	Rock void of uranium ore which may have been set aside as waste after removal of top-soil, overburden
and uranium ore or veins. Waste rock is defined as barren or submarginal rock or ore that has been
mined, but is not of sufficient value to warrant treatment and is therefore removed ahead of the milling
processes.
1-4

-------
reviewers' comments, we have clarified in each chapter where specific wastes described are not
considered TENORM and are subject to other agency regulations, and have added a new
Appendix (VI) which provides information on the regulatory authorities of the principal federal
and other agencies which oversee various aspects of uranium extraction and production. Errors in
fact and numbers cited which we could verify were corrected throughout the report. Uranium
price trends and mine production and reclamation status/ownership information was also updated
as of early 2006.
Origins of Uranium
Uranium has been around a long time. Cosmologists believe uranium was formed in supernovae
billions of years ago. Uranium is a metal found in most rocks on Earth in concentrations of one to
four parts per million. Uranium is in fact more abundant than gold, silver, mercury, antimony, or
cadmium, and more or less as common as tin, cobalt, lead, molybdenum, and arsenic (CRC
1994). And contrary to popular perception that uranium is somehow far away and isolated in
high-security facilities, traces occur almost everywhere—in plants, soil, rock, seawater, and
animals (including humans).
The German chemist Martin Klaproth is credited with discovering uranium in samples of the
mineral pitchblende in 1789. He named it for the planet Uranus, discovered only eight years prior.
Uranium was first isolated as a metal in 1841 by Eugene-Melchior Peligot. French scientist Henri
Becquerel is noted for (among other things) discovering the property of radioactivity while
observing radiation from the highly radioactive decay progeny (called radium) closely associated
in uranium-bearing rock (Ewing 1999).6 While "discovered" in the late 18th century, uranium had
nevertheless been used for many centuries as a colorant in glass and ceramics. Yellow-colored
glass containing one percent uranium oxide has been found in Italy dating to 79 A.D. (CRC
1994).
Physical Nature of Uranium
Uranium, a naturally occurring element with the atomic number 92, contributes to low levels of
natural background radiation in the environment. Uranium in ores can be extracted and
chemically converted into uranium dioxide (U02) or other chemical forms usable in industry.
When refined, uranium is a silvery-white metal with very high density—65 percent denser than
lead (CRC 1994).
Uranium is found naturally as three different isotopes7: U-238, U-235, and U-234. Other isotopes
can be synthesized (created by humans), but all uranium isotopes are radioactive to varying
degrees. Almost all uranium as found in nature is the isotope U-238 (Table 1.1). While in this
report, general reference to uranium will be to uranium in its natural isotopic proportion, unless
otherwise stated, it should also be noted that these proportions are not in fact entirely fixed.
6
See Appendix II for uranium decay series.
7	An isotope is a variant of an element (having the same number of protons) but a different number of
neutrons in the nucleus. For example, uranium has 92 protons. But uranium-238 has 146 neutrons, and
uranium-235 has 143 neutrons.
1-5

-------
Table 1.1. Percentage of Natural Abundance and Half-Lives8
of Uranium Isotopes by Total Weight
Almost all uranium as found in nature is the isotope U-238.
Isotope
Natural Abundance (%)
Half-Life (years)
U-238
99.2740
4.47 billion
U-235
0.7200
700 million
U-234
0.0055
246,000
Source: Eisenbud and Gesell 1997.
Uranium-238 undergoes radioactive decay into a long series of 13 different radionuclides before
finally reaching a stable state in lead-206. These radionuclides emit alpha or beta radiation and
some also emit gamma radiation of widely varying energies. EPA's glossary of radiation terms9,
defines radioactivity as "the process of undergoing spontaneous transformation of the nucleus,
generally with the emission of alpha or beta particles often accompanied by gamma rays" Some
of these progeny radionuclides are very radioactive and can pose human health risks. One of the
radionuclides in the series is actually a radioactive gas, radon-222, while the others are all solids.
Uses of Uranium in Industry
Uranium has more uses than many people are aware of, though most of them are fairly esoteric
(Table 1.2). By far, the greatest uses have been in nuclear weapons production and electric power
generation. Uranium has the rare property of being "fissionable." Its nucleus can be split, or
fissioned, and in the process, releases enormous amounts of energy (as well as significant
volumes of highly radioactive by-products). This realization in the late 1930s and early 1940s led
to a race by U.S. scientists to produce an atomic bomb during World War II. However, U-238, the
predominant isotope, is only nominally fissionable—not enough so for a workable bomb. Of the
three natural isotopes of uranium, U-235 is by far the most fissionable, (see Appendix II for
uranium-235 (actinium) decay series. There have been reported occurrences of uranium deposits
in Africa which underwent spontaneous nuclear fission, and which were detected based on
discrepancies in the ratios of uranium isotopes present in the geological deposit (Meshik 2005).
A half-life is the time in which one-half of the atoms of a radioactive isotope decay into another nuclear
form. Half-lives vary from less than a billionth of a second to billions of years. Also called the physical
or radiological half-life. Isotopes with longer half-lives tend to be more stable and less radioactive.
9 See on the Internet the following site: http://www.epa.g0v/radiati011/terms/termar.htm#r.
1-6

-------
Table 1.2 Multiple Industrial Uses of Uranium
Uranium has more uses than many people are aware of.
Types of Uranium
Industrial Uses
Primary Uses
Uranium
Nuclear weapons production and electric power generation.
Lesser-Known Uses
Uranium
For production of copper, nickel, and steel alloys to enhance specific properties.
For dating the Earth by making calculations based on the rate of decay of uranium
and the relative proportion of its stable progeny lead-206.
Incorporated into dental porcelain used for false teeth to simulate the fluorescence of
natural teeth (a relatively minor historical use).
Depleted uranium
For inertial guidance systems and gyro compasses.
Armor piercing conventional munitions, tank armor, and nuclear waste casks.
Refined uranium metal
For production of high-energy X-rays.
Uranyl nitrate
As a colored glaze for porcelain and glass and for manufacturing pigments (this
practice has more or less ceased in the United States).
Uranyl acetate
In dry-copying inks and as a reagent in chemistry.
Uranium salts
As mordants for dyeing silk and wool.
Compounds of uranium
For photographic toning, and staining and dyeing leather and wood.
Sources: NCRP 1987a; USGS 1973; U.S. NRC 2001.
To produce a functional uranium-based atom bomb, U.S. scientists needed a high concentration
of the isotope U-235. With great difficulty and cost, they separated the natural uranium isotopes
to increase the concentration of U-235 relative to U-238. This process is called enrichment,
because the extracted fraction is enriched in U-235 (to 90 percent or more for bombs). The
highly fissionable U-235 is also used to produce nuclear energy, but is typically enriched only
to about three percent (U.S. DOE 2002).
In addition to fission, atomic nuclei, such as uranium, can undergo a process called neutron
capture, which permits the generation of plutonium (Pu) isotopes. One of these, Pu-239, is even
more fissionable than U-235 and has very high energy outputs. Plutonium is made by
bombarding uranium-238 targets in specially designed reactors (Rhodes 1987).
The enrichment process produces huge quantities of remnant, depleted uranium that is almost
pure U-238. Depleted uranium is very stable and very dense, has poor fission properties, and is
only very weakly radioactive. Decades of uranium enrichment have generated enormous
quantities of depleted uranium. The U.S. Department of Energy has over 500,000 metric tons
(MTs) of surplus depleted uranium stored on site at two of its large enrichment facilities (U.S.
DOE 2002).
The uses of and markets for depleted uranium are fairly limited and are typically unrelated to any
nuclear properties. As such, its value is low. Perhaps the most notable use is in military munitions
and armored shielding. Like many other metals (e.g., magnesium), uranium is pyrophoric, which
means that it reacts quickly with oxygen. As a result, the rapid oxidation of small particles (which
have a relatively larger ratio of surface area to volume) of uranium can generate sufficient heat to
cause ignition. Consequently, due to this pyrophoric nature and high density, projectiles made of
depleted uranium burn on high impact and penetrate enemy armored tanks with ease. As
shielding, thick plates of depleted uranium effectively inhibit penetration from projectiles. Due to
its high density, depleted uranium finds domestic application in the keels of yachts, as ship
ballast, and as counterweights for control surfaces (rudders and elevators) in airplanes and
1-7

-------
helicopters. Also because of their high density, depleted uranium blocks are used for shielding
gamma radiation in research facilities.
Geology and Distribution of Uranium
The very large ionic size and chemical properties of uranium tend to allocate it to certain mineral
assemblages, and lend to fractionation and concentration of uranium in particular rock types.
Common uranium minerals include uraninite, coffinite, brannerite, carnotite, uranophane,
autunite, pitchblende, and torbernite. Of these, uraninite (nominally U 02 ..) is the most
widespread and significant economically, followed by coffinite (U(Si04)i_x(0H)4x), and
brannerite (U4+Ti206) (Finch and Murakami 1999).
Most deposits of uranium in the U.S. were formed when oxidizing groundwater, which dissolves
and transports uranium in a hexavalent10 state, combines with carbonate, sulfate, and phosphate,
and were subsequently reduced in their oxidation state by the presence of either organic matter or
iron disulfide in the rock formations. If this occurred, uraninite or coffinite would have
precipitated in a quadrivalent (four net positive ions) phase (Burns and Finch 1999). The inverse
of this reaction (i.e., dissolution of uranium in mineral form) is used for ISL and
hydrometallurgical processing of uranium (see Chapter 2), and introduction of bisulfide or
hydrogen sulfide is a process used in aquifer restoration (see Chapter 4).
As a result of its size and charge, the uranium atom does not tend to fit well into typical igneous
rock-forming minerals (such as feldspars, quartz, micas, amphiboles, pyroxenes, olivine, and
titanomagnetite) and tends to be concentrated in silica-rich magmas such as rhyolites and granites
(Burns and Finch 1999). Chemical weathering of these rocks is the likely process that leached out
uranium that was later deposited in sandstone-type uranium deposits (see below).
Where uranium is in sufficient concentration in rock to be economically recoverable, it is called
an ore body. More detailed information on ore deposit geology can be found in Guilbert and Park
(1996) and Edwards and Atkinson (1986). Uranium resources of U.S. economic interest are
primarily found in four main types of geologic deposits:
Sandstone Deposits
Sandstones contain approximately 33 percent of uranium resources worldwide, whereas they
constitute the main source of uranium (over 95% of reserves and production) in the United States.
The principal U.S. sandstone deposits of uranium are in the Colorado Plateau, the Wyoming
Basin, the Texas Coastal Plain, and Nebraska. Sandstone uranium deposits in the United States
were mostly commonly formed when uranium was introduced after the sediment was deposited,
whereas some sandstone uranium deposits in other parts of the world (most notably in Canada
and South Africa) are paleoplacers, in which uranium minerals were concentrated as heavy
minerals in the sediments as they were deposited.
An important subset of sandstone deposits are breccia pipe deposits found primarily in northern
Arizona; collapse structures in bedded sedimentary rocks resulted in the accumulation of uranium
in circular deposits mimicking volcanic rock structures. The presence of uranium, copper, silver,
vanadium and other valuable metals may occur in breccia pipes—the Orphan Mine (see
10 The oxidation state or oxidation number is defined as the sum of negative and positive charges in an
atom, which indirectly indicates the number of electrons it has accepted or donated. Hexavalent means
that the uranium atom has six more protons than electrons, and thus a net positive charge of +6.
1-8

-------
Appendix III) is an example of this type of deposit in which structural geologic features
controlled mineral accumulations in sandstones and mudstones.
Vein Deposits
Typically, these deposits occur in or near structures (faults, fractures, shear zones, etc.). Uranium
is mineralized in cavities, fissures, cracks, and similar porous openings in veins (as well as
breccias and pipes) usually cross-cutting the enclosing rock, and is usually present with
accumulations of ore minerals and gangue (non-ore minerals) distinctly different from the
surrounding rock. The dimensions of cracks and vesicles (openings or cavities in volcanic rocks)
may vary considerably, as can the overall size of the vein ore body. Some ore bodies have been
very small (several tons), but rich in uranium. Uraninite and pitchblende are the dominant
minerals, with some accessory minerals.
Phosphate Deposits
Sedimentary marine phosphorite is the primary source of uranium in this category. An estimated
four million tons of uranium could be extracted from U.S. phosphate deposits. While marketable
phosphatic material obtained from phosphate deposits typically contains only 50-200 ppm
uranium, the large quantity (approximately 150 million MTs per year) of crude ore rock produced
in the United States (Jasinski 2003) makes it a potentially significant source of uranium.
Disseminated Deposits
Typically, these deposits are associated with granites, pegmatites, and syenites. The size, shape,
and concentration of the ore bodies vary significantly. Secondary enrichment of the primary
mineralization helped to form the ore grade that typically ranges between 0.05 and 0.15 percent.
Deposits near Spokane, Washington, and Bokan Mountain in Alaska, are the most prominent
disseminated deposits in the United States, though their production was insignificant in
comparison to that derived from other types of deposits such as sandstones.
A fifth type of deposit is important to production in Canada:
Unconformity Deposits
This type of deposit is high-grade ore that occurs along and just below major Precambrian
unconformities. Ore is often associated with graphite schists.
In defining what is ore, assumptions are made about the concentration in the rock; the cost of
mining, processing, refinement, waste management, and site restoration; and the market value of
the metal. Material too low in uranium to merit processing and refinement is often called protore,
a nominal material that is currently uneconomical. Soil and rock that is otherwise essentially at
background uranium and radiation levels, which is removed to gain access to underlying ore, is
called overburden.
Most uranium mining in the United States has taken place in the expansive Colorado Plateau
region straddling the Four Corners where Utah, Colorado, New Mexico, and Arizona meet.
Figure 1.1 illustrates the extent of the Colorado Plateau and the general locations of uranium
mines within the Colorado Plateau, although not all mines are shown; for example, numerous
watersheds have over 100 mines by themselves. The source of the mine information used for this
map is the Minerals Availability System/Mineral Industry Location System database
(MAS/MILS) developed by the U.S. Bureau of Mines (McFaul et al. 2000), which has been
included as a portion of the EPA Uranium Location Database (U.S. EPA 2006b). These mines
have documented production, and represent over 4000 records contained within the larger EPA
database, which contains over 14,000 records. Other mine location information in the EPA
1-9

-------
database has been collected from several cooperating state, Tribal, and federal agencies. Mine
locations in the EPA database, including MAS/MILS sites, were compared to U.S. Geological
Survey topographic maps and one another in order to obtain an indication of accuracy and
reliability. While the MAS/MILS data has known flaws, and sites shown in Figure 1.1 do not
constitute all known uranium mines and fields, it provides a general overview of uranium mine
geographic distributions in the western U.S. The larger data sets that comprise the EPA Uranium
Location Database are discussed in the database documentation (U.S. EPA 2006b).
Major geologic formations noted for high uranium are the sedimentary Chinle (Triassic) and
Morrison (Jurassic) Formations. The Chinle and Morrison are characterized by permeable
streambed deposits of highly variable sized and sorted pebbles and sands, with associated
concentrated pockets of organic matter from trees, branches, grasses, etc. Later blankets of
volcanic ash provided a source of uranium to leach into the permeable rocks of the Chinle and
Morrison. The uranium-laden leachate followed the highly permeable stream channel and
mudstone formations, and upon reaching the reducing environment caused by high organic
matter, precipitated uranium into void spaces, typically as uraninite. The association with
organics resulted in some locales where very small—but very high-concentration—uranium
deposits have been found, including as petrified logs. Thus, one-man mining operations could
target small, rich deposits profitably.
Uranium's Contribution to Natural Background Radiation
Uranium is found in all rock types in varying, but usually small concentrations. Naturally
occurring elemental radium and its radioactive decay products can emit radon to the Earth's
atmosphere. This section provides a basic discussion on natural background radiation.
Background Gamma Radiation
Numerous studies have examined the occurrence of uranium and its radioactive decay products in
U.S. soils. Table 1.3 presents average concentrations of some radionuclides found in igneous and
sedimentary rocks that are the principal radionuclides referred to as NORM. There can be more
than an order of magnitude difference in radionuclide contents among common igneous rocks.
Similarly, deposits known as black shales, found in the eastern U.S. along the Appalachian
Mountain front, are not uncommon rocks but are not similar to other U.S. shales as they typically
have elevated uranium concentrations.
1-10

-------
Figure 1.1. U.S. Geographic Areas Rich in Uranium
Most uranium mining in the United States took place in the expansive Colorado Plateau region
straddling the Four Corners where Utah, Colorado, New Mexico, and A rizona meet. This map
shows mine locations plotted from McFaul etal. (2000) MAS/MILS database; not all known mine
locations are included in that database, so some fields may not be represented. Readers looking
for more complete information on state mine locations should refer to U.S. EPA (2006b).
Extent of Colorado Plateau
* * Wyoming
Nebraska
j Co(o/Mo
Oklahoma
Arizona
Kilometers
Nevada
California
New Mexico
Legend
~ Colorado Plateau Boundary
x Uranium Mines W/Past Production
State Boundaries
1-11

-------
Table 1.3 Concentrations of Certain Natural Radionuclides
in Igneous and Sedimentary Rocks
A concentrating effect can occur as a result of weathering and erosion of igneous rocks. With the
exception of uranium-238, concentrations of radionuclides are generally higher in sedimentary
rocks. The radionuclides listed are principal NORM radionuclides. The radionuclide contents
shown here should be considered average values. Individual rock deposits can have radionuclide
contents that may differ significantly from the numbers shown.

Radium
Uranium
Thorium
Potassium
Rock type
Ra-226
Ra-226
U-238
U-238
Th-232
Th-232
K-40
K-40

pCi/g
Bq/kg
pCi/g
Bq/kg
pCi/g
Bq/kg
pCi/g
Bq/kg
Igneous
1.30
48
1.30
48
1.30
48
22.0
810
Sedimentary








Sandstone
0.71
26
0.40
15
0.65
24
8.8
330
Shale
1.08
40
0.40
15
1.10
41
22.0
810
Limestone
0.42
16
0.40
15
0.14
5
2.2
81
Note: Units are in picocuries/gram and Becquerels/kilogram.
Source: Eisenbud and Gesell 1997.
Radium (a decay product of uranium) primarily decays by alpha particle emission. Its own short-
lived radioactive decay products, such as polonium-210 or bismuth-214, yield more gamma ray
emissions over time, making radium an important contributor to overall human and
environmental exposure to radiation, or radiation dose. In general, concentrations of radium-226
in U.S. soils range from 0.4 to 1.3 pCi/g (16 to 48 Bq/kg) (Eisenbud and Gesell 1997), with lower
concentrations found in the eastern part of the country, and higher concentrations in the West.
Higher concentrations may also be found in locations with uraniferous igneous and sedimentary
rocks, as well as phosphatic rock deposits. In addition to radium-226, uranium-238, uranium-235,
and thorium-232, there are radioactive decay products that may substantially add to the
radioactivity present where these radionuclides are in equilibrium to their decay products in
uranium deposits, and mine or mine waste locations
Primary contributors of radiation from the natural environment are soil gamma ray radiation and
inhaled radon. A 1987 study (NCRP 1987b), citing a 1972 review by Oakley, estimated gamma
radiation doses to the U.S. population from terrestrial sources, based on aerial radiological
measuring surveys by the U.S. Atomic Energy Commission (Table 1.4 and Figure 1.2). Annual
doses for people living in brick homes may increase up to 10 milliRems/year (mRem/yr) due to
naturally occurring thorium, uranium, and radium found in clays often used to make bricks.
Additional data on the distribution of radium in the U.S. can be found in Myrick et al. (1981).
Two additional studies of the National Council for Radiation Protection (NRCP 1993, 1984)
examined the impacts of exposure to uranium and it's radon daughter decay products, and
radiation protection in the mineral extraction industry, respectively.
1-12

-------
Table 1.4 Absorbed Dose Rate in Air from Terrestrial Radiation Sources
(in milliReins/year, milliSieverts/year and niicroGrays/year)
Natural geologic accumulations of radionuclides in the Colorado Plateau,
the principal mining area for uranium in the United States,
result in increased exposure rates for humans living in that environment.
region
1960 Population
Covered by Surveys
Absorbed Dose Rate in
Air
(microGy/yr)
Dose in mrem/yr
(mSv/yr)
Coastal Plain
6,759,772
230
23 (0.23)
Non-coastal Plain (excluding
Denver)
46,781,330
460
46 (0.46)
Colorado Plateau (Denver)
1,073,624
900
90 (0.90)
Population-Weighted Average
440
44 (0.44)
Note: Results are based on population-weighted aerial radiological survey data.
100 microGv/yr x 0.1 =0.10 mSv/yr = 10 mRem/yr. Rem = Roentgen equivalent in man.
Sources: NCRP 1987b; Oakley 1972.
Figure 1.2 Gamma Ray Radiation Across the United States
Terrestrial Gamma-Ray Exposure at lm above ground.
Mote: Results are based on national aerial gamma ray surveys..
Colors,'shading reflect exposure in flR, per hour (micro Roentgens per hour) according to the map.
Source: USGS 1993.
1-13

-------
Radon in Homes
The average radiation dose to an individual in the United States from all sources is about 360
mRem/yr (3.6 milliSieverts). Typical values for annual exposure to radiation within the United
States are summarized in Table 1.5. Radon occurs in the environment and is listed separately in
that table because of radon's significant contribution to radiation exposure: 200 mRem (two mSv)
of the estimated average dose from all sources.11 Most of the radon dose comes from indoor
exposure in homes, schools, and other buildings. The radon is generated by rocks and soil
underlying the man-made structures; it seeps into the buildings through cracks and pore spaces of
the foundations. Some radon is also generated from the building materials used in construction.
Figure 1.3 presents short-term screening average U.S. indoor air concentrations of radon by
county.12
Table 1.5 Average Annual Human Exposure to Radiation
Natural sources of human exposure to radiation, primarily in the form of radon,
usually outweigh manmade sources, though medical exposures have
become more prominent in recent years.
Sources of Radiation
Average Exposure
in mRem/yr (mSv/yr)
Typical Range of Variability
in mRem/yr (mSv/yr)
Natural Sources
300 (3)

Radon
200 (2)
30-800 (0.3-8)
Internal
40 (0.4)
20-100 (0.02-1.0)
Cosmic
30 (0.3)
30-80 (0.3-0.8)
Terrestrial
30 (0.3)
10-80 (0.1-0.8)
Man-made Sources
61(0.61)

Medical
50 (0.5)

Consumer products
10(0.1)

Other (nuclear fuel cycle and occupational
exposure)
1 (0.01)

Total
361 (3.6)
90-1,060 (0.9-10.6)
Sources: NCRP 1987b for average exposure values;
U.S. NRC 1994for ranges of variability; Fisher 2003for radon.
Cosmic radiation comes from outer space. Some of it penetrates through the atmosphere covering the Earth.
The amount of cosmic radiation will vary, depending on the altitude and latitude where one lives. Internal
radiation comes primarily from ingested natural radioactive substances, such as potassium-40.
12 See http://www.epa.gov/radon for more information.
1-14

-------
Figure 1.3 Average Indoor Air Screening-Level Concentrations
of Radon in the United States
The highest radon levels are generally reflected in counties located along
the Appalachian Mountains, Rocky Mountains, and north central states.
£=PA Map of Radon Zones
Legend
Zone 1
Zona 2
Zone 3
Average Indoor Screening Levels
Zone 1 counties: greater than 4 pCi/L (0.148 Bq/L)
Zone 2 counties: between 2 and 4 pCi/L (0.074 and 0.148 Bq/L)
Zone 3 counties: less than 2 pCi/L (less than 0.074 Bq/L)
Note: See http://-www.epa.gov/iaq/radon/zonemap.html to access an on-line
version of this figure, which allows countv-bv-coimtv information.
Source: U.S. EPA 1993c
Uranium in Water
Just as uranium is found in virtually all rock and soil, it is essentially ubiquitous in groundwater.
Groundwater concentrations tend to reflect overall bedrock averages and can vary widely. While
surface waters, originating primarily from rain and snow melt, are typically very low in uranium
and other TENORM radionuclides, to the point where they cannot be measured, groundwater can
be relatively high in radionuclides of both primary and anthropogenic origin.
Water is perhaps the most significant means of dispersal of uranium and related TENORM in the
environment from mines and mine wastes. Surface waters contaminated by surface erosion of
mines and wastes maypercolate into groundwater, and contaminated water travels underground
through mines or drill holes into the groundwater. Uranium is very soluble in acidic and alkaline
waters and can be transported easily from a mine site. Radium may be leachable as well as carried
in particulate form by flowing water (Eisenbud and Gesell 1997). More detail on this topic can be
found in Chapter 3. Occurrence of uranium and radium in water has been detailed in case studies
on the Orphan Mine, Midnite Mine, Bluewater, and Yazzie-312 Mine (see Appendix III).
EPA has updated its standards for maximum contaminant levels for radionuclides in drinking
water (40 CFR 141.66), including a new standard for uranium (65 FR2000a 76708, December 7,
2000), as required by the 1986 amendments to the Safe Drinking Water Act. The standards are:
1-15

-------
combined radium 226/228 internal (five pCi/L) (0.185 Bq/L); man-made beta emitters (four
mRem annual dose equivalent to the total body or any organ) (0.04 mSv); gross alpha (excluding
uranium and radon) standard (15 pCi/L) (0.56 Bq/L); and uranium (30 (.ig/L). The reader should
understand that the uranium standard was based on its identified toxicity to the kidney, and not its
potential for causing cancer.
Under the Clean Water Act (See Appendix VI for more detail), mines and mills that discharge
must obtain a permit, and must monitor twice a year for specific pollutants determined by the
type of ore they mine or process. EPA regulations in 40 CFR 440, Part C, are applicable to
discharges from (a) mines either open-pit or underground (ISL operations are excluded), from
which uranium, radium and vanadium ores are produced; and (b) mills using the acid leach,
alkaline leach, or combined acid and alkaline leach process for the extraction of uranium, radium
and vanadium. Only vanadium byproduct from uranium ores is covered under this subpart. With
certain exceptions, primarily concerning unusually high storm water events, for existing and new
point source dischargers, the maximum concentration for one day of dissolved radium-226
allowed to be discharged is 10 pCi/L with an average 30 day value of three pCi/1, for total
radium-226 the amount allowed to be discharged for one day is 30 pCi/L and 10 pCi/L for an
average 30 day concentration. For uranium discharges, the maximum allowable discharge for one
day is four milligrams/L, while an average of no more than two milligrams/L is allowed to be
discharged over a 30 day period. The same numerical standards for radium apply to uranium
mills, though there is no uranium discharge standard.
Industrial Processes and Activities
TENORM may be generated during extraction, processing, treatment, and purification of
minerals, petroleum products, or other substances obtained from NORM-containing parent
materials. TENORM also includes any radioactive materials made more accessible by human
activities. Several hundred million metric tons (MTs) of TENORM are generated each year by a
wide variety of industrial processes, ranging from uranium and phosphate mining to the treatment
of drinking water. Although conventional uranium mining is the central focus of this report and
will be discussed in more detail in Chapter 2, the section below briefly discusses activities or
processes, other than uranium mining, that produce TENORM as a result of the co-occurrence of
uranium and its daughter radionuclides in the source rock, soil, or water. However, not all ores of
these commodities contain uranium or radium at concentrations above natural background levels
in associated rocks. In some instances, the radioactive wastes from mineral processing other than
uranium mines have been used as source rock for uranium extraction under NRC license.
Uranium Associations with Other Metal Mining
Quite typically, beginning in the 1940s, uranium mines would open based on the detection of
radioactivity at the site and identification of uraniferous mineralization. While some deposits
were mined solely for their uranium content, others produced a variety of other minerals, which
co-exist with the uranium minerals (Table 1.6). In some cases, exploitation of uranium minerals
was secondary to producing another mineral found in greater abundance, commanding a better
market price, or less expensive to produce; nevertheless, their combined economic value
contributed to the success of the mining venture.
1-16

-------
The presence of radioactive minerals was sometimes unexpected, unknown, or ignored in
producing one or more minerals at a mine. Many mine sites operated prior to the 1940s, and even
after, have not been recognized for the inherent hazards potentially posed by radioactivity in the
discarded waste rock or subeconomic ore piles. The geological emplacement or geothermal
phenomena that formed other valuable minerals may have concentrated radioactive minerals as
well, or the process of mining, beneficiation, and milling may have resulted in a concentration of
the radioactive minerals in the waste. In some instances, the mineral(s) being mined may have
radioactive elements included in their molecular structure that impart radioactivity to the ore or
even the finished product. The EPA (U.S. EPA 2006b) Uranium Location Database provides the
location of mines with uranium occurrence including those that may have been mined primarily
for other minerals.
Table 1.6 Mineral Commodities with Uranium Associations
Several mineral ores often, though not always, have TENORM-associated
wastes resulting from the co-occurrence of uranium and radium.
Aluminum (bauxite)
Potassium (potash)
Coal (and coal ash)
Precious metals (gold, silver)
Copper
Rare earths: yttrium, lanthanum, monazite, bastanite, etc.
Fluorospar (fluorite)
Tin
Gypsum
Titanium (leucoxene, ilmenite, rutile)
Molybdenum
Tungsten
Niobium
Vanadium
Phosphate (phosphorus)
Zircon
Source: U.S. EPA 2003b.
Copper Mining
Copper mines have long known to be associated with uranium occurrences internationally, as
well as in the U.S. The Bingham Canyon copper mine in Utah produced 150,000 pounds of
uranium per year from 1978-1985 and 10,000 pounds per month from February 1987 through the
end of 1989 (Chenoweth 1991). The Orphan Mine in Arizona (see Appendix III) was originally
claimed for its copper mineralization, but only began production in the 1950s as a result of its rich
uranium occurrence. Other mines in the southwest, such as the Yerington Mine in Nevada and
Anaconda Mine in Utah have also been reported to have uranium mineralization or production.
Uranium recovery from copper leaching is described in McGinley (1980). EPA's report (U.S.
EPA 1999) on copper mining in Arizona provides extensive information on TENORM radiation
associated with copper mine wastes and groundwater impacts, both from conventional and ISL
extraction facilities in that state. Some of the mines listed also were licensed by the Atomic
Energy Commission (precursor to the NRC) to produce uranium in addition to copper.
Phosphate Production
Uranium is known to associate with phosphatic deposits primarily because hexavalent uranium
complexes well with dissolved phosphate. Phosphate rock contains phosphorite, a form of the
mineral apatite, which is known to accommodate uranium. Phosphate rock is the sixth largest
mining industry in the United States in terms of volume of material mined. It is mined for the
production of phosphoric acid, the great majority of which is used in agricultural fertilizer. About
80 percent of U.S. phosphate mining occurs in south central Florida, though some mining also has
occurred in North Carolina, Utah, Idaho, Wyoming, Tennessee, and a few other states (U.S. EPA
1989b; Jasinski 2003).
1-17

-------
The phosphate fertilizer industry is a major generator of TENORM. Uranium concentrations in
phosphate rock range from 14 to 200 pCi/g (20 to 300 ppm, or about 0.5 Bq/g to 7 Bq/g), and
radium concentrations are 18 to 84 pCi/g (about 0.7 to 3 Bq/g) (DeVoto and Stevens 1979). In the
United States alone, some 150 million MTs of phosphate ore are produced each year, which contain
radioactive thorium and its decay progeny, in addition to uranium TENORM. Mineral processing
sometimes exposes workers to measurable doses of radioactivity.
Phosphate ore is crushed and digested in sulfuric acid to produce orthophosphoric acid and
phosphogypsum. Phosphogypsum is a complex mixture of gypsum (CaS04-2H20), silica, and
anhydrite (CaS04). In the process, various other wastes are also formed. Between 80 and 100
percent of the radium in phosphate rock is transported to the phosphogypsum, while about 70
percent of the uranium (and thorium) remains in the phosphoric acid (however, the fractionation
of uranium and thorium is variable and still not well characterized) (Guimond 1975; Hull and
Burnett 1996; FIPR 1995).
Though uranium concentrations in phosphate ore are low compared to typical uranium ores, the
low cost of uranium recovery from secondary phosphate products sometimes makes it profitable
to extract uranium as a by-product of phosphate production. Phosphate rock and tailings
containing up to 120 ppm of uranium have been mined as a source of uranium (DeVoto and
Stevens 1979).
Before EPA required placement of phosphogypsum in environmentally isolated waste piles,
called "stacks", to control radon emissions (40 CFR 61, Subpart R), phosphogypsum and waste
rock containing uranium and thorium were often used to refill and reclaim open mine pits. Due to
pressures to find available land for home building, several of these reclaimed mine pits were
subsequently sold as home sites. In 1975, EPA reported that more than 1,000 houses were built
over these sites in one Florida county alone. While it has not been determined if this housing may
pose a radiation hazard to the occupants, during its study EPA found some elevated levels of
radiation and radon (U.S. EPA 1975).
Elemental phosphorus is produced by the thermal process. It is a raw material used primarily in
chemical and food production, primarily from ore deposits in Idaho. This process also produces
TENORM wastes, such as slags, containing radium and uranium.
Coal Combustion
Most coal contains uranium and its progeny radionuclides at levels about the same as, or less than
other rocks of the Earth's crust (UNSCEAR 1982). Uranium TENORM emerges from coal-
burning plant furnaces predominantly in fly ash, which is fused and chemically stable. Coal fly
ash is derived from inorganic materials that were co-deposited with the organic detritus that
produced the coal beds. Uranium in coal may be a combination of detrital mineral matter and
uranium deposited later through adsorption by, or oxidation of, organic matter in the lignite or
coal. In one instance in the 1960s, certain lignitic coals from North Dakota were mined and
burned in order to further concentrate the high levels of uranium already present in the coal; the
resulting ash was then taken to a uranium mill in Colorado to process into uranium yellowcake13.
13 See http://www.eia.doe.gov/cneaf/nuclear/page/umtra/belfield title 1 .html for more information.
1-18

-------
Principal nonradioactive ash constituents are the metal oxides of silica and alumina, often
comprising 80-90 percent, with smaller percentages of other metal oxides, including iron,
calcium, sodium, tin, magnesium, and potassium. Pollution control devices in modern power
plants usually capture about 99 percent of fly ash, and devices in some older plants capture about
90 percent. However, those devices do not capture radon gas. In addition to ash, power plants
produce slag, sludge, and other waste products that may contain uranium TENORM.
The amount of ash generated is proportional to the amount of coal consumed and the coal ash
content. The ash content of coal will vary according to the depositional environment. The average
ash content of coal burned by the U.S. electric utility industry is approximately 10 percent,
meaning that uranium in coal is concentrated roughly 10 times in the ash. For coal with a 10
percent ash content, a 1,000 megawatt plant may produce over 1,500 tons of ash during a 24-hour
period. However, the actual quantity of ash produced also depends on the plant's design and
efficiency and the coal's energy content.
Though the concentrations are low, the total amount of TENORM in fly ash is noteworthy (Beck
et al. 1980; Beck 1989). For example, in 2004, U.S. electric power plants burned approximately
921 million MTs of coal (U.S. DOE/EIA 2005d). If that amount of coal is burned with 1.5 ppm
uranium, 1,381 MTs of uranium would be concentrated, in addition to other TENORM quantities.
Other coals are quoted as ranging from up to 25 ppm of uranium and 80 ppm of thorium. Based
on analyses of nearly 7,000 samples, of all coal provinces and coal ranks, an EPA study found
that the range of uranium in U.S. coal was 0.010-75 ppm (U.S. EPA 1995b).
Most fly ash is buried, but increasingly fly ash is being used for commercial applications. A
significant quantity of fly ash (Class C) is considered cementitious (having the properties of
cement, the principal binding agent in concrete) which makes it a very useful material. The
relatively uniform small particle size, surface reactivity, and bulk chemical
composition—particularly if alkali elements are abundant—lend properties to coal ash, slag, and
flue gas waste material that have numerous useful commercial applications. These include:
flowable fill, structural fill, road base/subbase, coal mining applications, mineral filler in asphalt,
snow and ice road control, blasting grit and roofing granules, grouting, waste solidification and
stabilization, and wall board (ACAA 1995, 1996; U.S. DOE/EIA 1993; EPRI 1988).
Heavy Mineral Sands
Many of the minerals which make up this commodity contain significant percentages of uranium
and thorium. As a result of their inherent hardness, weight (specific gravity), and other physical
properties, certain minerals are naturally resistant to erosion and to physical and chemical
breakdown over geologic time. Accumulations of these minerals results in sedimentary sand
deposits commonly called "heavy mineral sands," or sometimes "black sands," because they are
dominated by black minerals. These deposits, if they occur in easily accessible locations and in
sufficient size, may be mined to concentrate and extract valuable industrial metals (U.S. EPA
1990).
Typical minerals that may be found in these deposits include garnet; titanium-rich rutile, ilmenite,
and leucoxene; thorium-rich monazite; and uranium-rich zircon. All of these minerals, and
several others typically occurring in the deposits, are radioactive due to: the presence of uranium,
thorium, and radium in their molecular matrix; radioactive coatings washed into the deposits from
elsewhere; or the chemical and physical weathering of radioactive mineral grains in the sand
deposit. The wastes from extracting these minerals, and often the finished products resulting from
mineral processing, may retain some or all of their natural radioactivity (CRCPD 1994).
1-19

-------
Although monazite is mined incidentally along with other minerals in heavy mineral sand
deposits, it is not currently being used commercially in the United States, and is usually returned
to the extraction site as a waste. The uranium oxide content of monazite sands in the Southeast
was measured at 0.47 percent (Mertie 1953). Monazite from the Green Cove Springs deposit in
Florida, which produced monazite prior to 1995, averaged 4.44 percent thorium oxide (Staatz et
al. 1980).
The major U.S. mining operations for titanium sands have been located in Stoney Creek,
Virginia, and Simi Valley, California, and along the Trail Ridge formation, an ancient sand dune
deposit that extends from northeastern Florida to southeastern Georgia. However, most titanium
ore (separated sands mostly, rather than finished titanium dioxide powder) is imported. Although
as a metal, titanium is well known for its corrosion resistance and for its high strength-to-weight
ratio, approximately 95 percent of titanium is consumed in the form of titanium dioxide pigment
in paints, paper, and plastics. Other end uses of titanium include ceramics, chemicals, welding rod
coatings, heavy aggregate, and steel furnace flux (USGS 1973). There has been no study on
disposal of any residual radioactive wastes from these industries in the U.S.
Zirconium is a silvery-white metal obtained from zircon sands (Brady et al. 1997), while hafnium
is a ductile metal, with a brilliant silver luster. Most zirconium minerals contain 1-5 percent
hafnium (CRC 1994). Zircon production is usually a byproduct of mining and extracting titanium
minerals from ilmenite and rutile ores. Zircon has been produced from dredging operations in
Florida, and now Virginia. Major end-use categories for zircon include abrasives, ceramics,
refractories, and foundry applications. Zircon is consumed directly for abrasives and welding and
as welding flux. Zircon sands and finely ground zircon (termed zircon "flour") are consumed in
foundry molds, refractories, and ceramics. Residual radioactive wastes from these industries have
been reported to be disposed in industrial landfills, and there have been instances where
abandoned barrels of zircon flour, and sites contaminated with zircon wastes have been the
subject of Superfund cleanup and removal actions. Table 1.7 presents radioactivity concentrations
reported by the CRCPD for zircon and titanium process ore and wastes
Table 1.7 Radionuclide Concentrations in Process and Waste Samples
Radium concentrations can be highly variable for titanium
and zircon ores and wastes, and dependent on ore source.
Process Ores
226 Radium Concentrations in pCi/g (Bq/Kg)
Titanium
Rutile
15 (555)
Leucoxene
12 (444)
Dry ponds (~5 cm depth)
45 (1665)
Dry ponds (surface)
20(740)
Settling pond solids
17(0.73)
Sludge pile
4-25 (148-925)
Zircon
Chlorinator residues No. 1
150-1,300 (5550-48100)
Chlorinator residues No. 2
230-890 (8510-32930)
Clarifier sludge
87-150 (3219-5550)
Source: CRCPD 1994.
1-20

-------
Chapter 2. Uranium Mining and Extraction Processes in the United States
In 1946, Congress passed the Atomic Energy Act (AEA), establishing the Atomic Energy Commission
(AEC) and designating it as the sole purchasing agent for domestically produced uranium. The AEA also
set fixed prices for uranium ore and provided production incentives (e.g., including access roads, haulage
allowances, and buying stations) in an effort to bolster development within the domestic uranium
industry. Since then, the industry has gone through two boom-to-bust cycles (U.S. DOE/EIA 1992). The
first of these cycles, in the 1950s, was prompted by the demand generated by the U.S. government's
weapons program. The second, in the 1970s to early 1980s, was fueled by expectations for increasing
demand from commercial nuclear power production and the "energy crisis". Since the 1970s, the NRC
succeeded the AEC in the role of licensing uranium extraction operations, but the demand and price of
uranium has been determined by external market forces. Rising demand, beginning in 2003 for uranium
has begun to increase production in the domestic industry. The importance of the uranium market and
price of uranium is their role in mining industry decisions. Some of these decisions are: how to extract ore
from a mineral deposit, how many and which mineral deposits should be mined, and when they should be
mined. Those decisions ultimately affect the volumes of waste produced and how it is managed.
This chapter examines the location and geology of uranium deposits in the United States, the methods
used to mine uranium, and the methods used to extract it from ore. Many of the geological and mining
terms used in the text that follows are defined in the chapter and are also in included in the glossary in
Appendix I.
The Early Years of Uranium Production
As a result of the AEC's financial incentives—first announced in 1948 and 1949 and then increased in
1951—uranium prospectors searched prospective areas of the United States throughout the 1950s for
radioactivity that might signal a viable uranium deposit. Prospectors locating areas with mining potential
would file claims for the discovery site and nearby areas. The ownership claims were regulated according
to the Mining Law of 1872 and were enforced by the U.S. Department of Interior. To maintain ownership
of these claims, prospectors needed to perform a variety of activities every year, including digging small
pits, adits1, and trenches. If they found ore grade material higher than 0.10 percent uranium, they would
mine the material and ship it to regional AEC buying stations for sale. AEC offered bonuses for
shipments meeting minimum criteria.
In many parts of the Colorado Plateau, the characteristic geologic forms of uranium ore bodies were small
to moderate-sized isolated pods or linear sinuous channels of ore, as opposed to large lithologic2 beds
typical of coal or iron. As a result, thousands of diminutive mines were developed in the Plateau region
on ore bodies sometimes as small as a single uraniferous petrified log weighing a few metric tons. In
many cases, these ore bodies were clustered into districts (Table 2.1.), and ores were shipped from
producing properties to centralized mills. These small mines produced small quantities of waste rock
typically discarded within several to over 100 yards (several to about 100 meters) of the mine opening or
pit. Mine maps typically show extensive underground mining following ore zones with only small piles of
1	Adits are horizontal or nearly horizontal passages driven from the surface for the working or dewatering of a mine.
If driven through a hill or mountain to the surface on the other side it would be a tunnel.
2	Lithologic is defined as character of a rock described in terms of its structure, color, mineral composition, grain
size, and arrangement of its component parts; all those visible features that in the aggregate impart individuality to
the rock. Lithology is the basis of correlation in coal and other types of mines and commonly is reliable over a
distance of a few to several miles.
2-1

-------
waste rock at the mouth of the mine entry. Mines of this type, now abandoned, are scattered over wide
areas of southeastern Utah, southwestern Colorado, northwestern New Mexico, and northeastern Arizona,
as can be seen in Figure 2.1. As described further in Chapter 3 of this report, the mines which were
abandoned or left unrestored prior to the early 1970s left residual wastes that are a main focus of this
study. The migration of radionuclides and other hazardous substances from those mines and their waste
piles have resulted from biologic, hydrologic, wind, and human actions, and are discussed in more detail
in Chapter 3 and Volume II of this report (U.S. EPA 2006a).
The primary database for uranium mine locations for the public has been the MAS/MILS (McFaul et al.
2000) database. However, the MAS/MILS data used to construct Figure 2.1 has known flaws, and sites
shown on the map using the database do not constitute all known uranium mines and fields. For example,
the Crow Butte in situ leach (ISL) field in Northwest Nebraska near the Wyoming border is not included;
however Figure 2.9, based on different data compiled in the EPA Uranium Location Database (U.S. EPA
2006b), does show the location of the Northwest Nebraska uranium district. The MAS/MILS database
though, does provide a general overview of uranium mine geographic distributions in the western U.S.
The larger data sets that comprise the EPA Uranium Location Database are discussed in the database
documentation (U.S. EPA 2006b).
Table 2.1. Major U.S. Uranium Mining Districts
Several major uranium districts produced uranium ore in the past
and contain potential for future exploitation.
Uranium District
State
Spokane
Washington
Wind River
Central Wyoming
Wyoming
Washakie Sand Wash
Wyoming, Colorado
Powder River
Wyoming, Montana
Northwest Nebraska
Nebraska
Uravan
Front Range
Marshall Pass
Tallahassee Creek
Paradox Basin, Colorado & Utah
Paradox Basin
Colorado, Utah
Marysvale
Utah
Northern Arizona
Arizona
Grants Mineral Belt
New Mexico, Arizona
Texas Gulf Coast
Texas
Source: U.S. DOE/EIA 1997.
2-2

-------
Figure 2.1. Mines and Other Locations with Uranium in the Western U.S.
Thousands of uranium mine sites are scattered over wide areas of the western United States.
This map shows locations provided in the MAS MILS database.
Source of Mine Information:
Legend	EPA Uranium Location Database
Km	N
MAS/MILS Uranium Mines	500
Source: (LIS. EPA 2006b)
2-3

-------
Large companies were also in the uranium prospecting business. Many mining properties proved to have
much larger ore bodies than originally thought, both on the Colorado Plateau and in other states.
Extensive mining operations were developed at these sites. Since the early 1960s, most uranium has been
mined on a larger scale than early mining efforts and conventional mining techniques were established to
recover the ores.
Although the AEC incentives ceased in 1962, the agency continued to purchase ore from properties with
reserves discovered before November 24, 1958, at guaranteed prices through the end of 1970. Initially,
the AEC paid $8.00 per pound, but this declined to $6.70 per pound in the late 1960s (Chenoweth 2004).
Several ore processing mills closed from late 1959 through the end of the 1960s. In 1961, for the first
time since 1948, uranium production declined in the United States. By the end of the buying program in
1970, several hundred small to intermediate-sized underground and open-pit mines were either mined out
or had become uneconomical and were abandoned.
The industry was revitalized shortly thereafter by the prospect of supplying fuel to the developing
commercial nuclear power industry. The production and market prices of uranium grew rapidly through
the mid- and late 1970s and early 1980s, as commercial markets began to emerge. However, production
and prices peaked in the early 1980s, when domestic demand for uranium ore fell far short of its expected
growth, and low-cost, high-grade Canadian and Australian deposits began to dominate world markets. As
planning and construction of new U.S. commercial nuclear power plants came to a halt (U.S. DOE/EIA
1992) and the domestic price of uranium dropped dramatically, the U.S. industry shifted from higher-cost
to lower-cost production sites, and the nation faced an oversupply of uranium despite the fact that demand
remained about even through 2003.
Throughout the high uranium production years, trends in the industry changed, leading to new mining
methodologies and subsequent changes in the nature of their resulting waste generation and hazards.
Environmental concerns and regulatory requirements, as well as discovery of high uranium content
deposits with low extraction costs, resulted in increased uranium mining overseas. Traditional mining
techniques can have high associated costs for heavy metal and TENORM waste management, acid mine
runoff, and mine site restoration. These issues made many uranium mines unprofitable when market
prices were low. Increasing world demand raised the price of uranium starting in 2003 (AAPG 2005) and
although most mines that were inactive at the time employed the less disruptive ISL technique, (described
in the following section), conventional mine sites have begun to reopen as a result (Teluride Watch 2005).
Conventional Uranium Mining Methods
The following discussion describes physical methods of mining. Mining is the mechanical process by which
mineral ores are extracted from the earth. These methods are referred to in this report as conventional
mining methods, as opposed to the solution chemical extraction processes of ISL and heap leaching.
Ore is a mineral source from which a valuable commodity (e.g., metal) is recovered. The term ore implies
economic viability, given the concentration of metal in the host rock, the costs of extraction, processing and
refinement, waste management, site restoration, and the market value of the metal. Protore is conventionally
mined uranium ore that is not rich enough to meet the market demand and price. This subeconomic ore is
often stockpiled at the mine site for future exploitation under the appropriate economic or market demand
conditions. Waste materials that are, or could be classified as, technologically enhanced, include
overburden, unreclaimed protore, waste rock, drill and core cuttings, liquid wastes and pit water (for more
detailed discussion, see Chapter 3). The size, grade, depth, and geology of an ore body (or deposit) are used
in combination to determine which extraction method is most efficient and economical. Conventional
2-4

-------
mining generally refers to open-pit and underground mining. Open-pit mining is employed for ore deposits
that are located at or near the surface, while underground mining is used to extract ore from deeper deposits
or where the size, shape, and orientation of the ore body may permit more cost-effective underground
mining. Since the early 1960s, most uranium has been mined on a larger scale than earlier mining efforts,
and, until recently, by using conventional mining techniques. Radioactive mine wastes from conventional
open-pit and underground mines are considered to be TENORM, whose regulatory responsibility resides
with EPA or the states. In recent years, ISL operations (regulated by the NRC or its Agreement States) in
the United States are described further below. Those operations have generally replaced conventional
mining because of their minimal surface disturbance and avoidance of associated costs (See Appendix VI
for discussion on statutory and regulatory authorities).
Open-Pit (Surface) Mining
Open-pit mining is the surface removal of soil and rock overburden and extraction of ore. Open-pit mines
are broad, open excavations that narrow toward the bottom, and are generally used for shallow ore
deposits. The maximum depth of open-pit mining in the United States is usually about 550 feet (168
meters). Lower-grade ore can be recovered in open-pit mining, since costs are generally lower compared
to underground mining. There are deeper surface mines for copper and other minerals (Berkeley pit in
Butte, Montana, reportedly at the north end is approximately 1780 feet, or 543 meters deep). Figure 2.2
shows a commonly used excavation method for removing overburden from surface mines, whereas Figure
2.3 shows the layout of a larger surface mine operation.
Delineation of the ore deposit by drilling and computer modeling is followed by development of a plan
for removing and disposing of overburden. This planning is important, since the handling of waste
material comprises one of the largest shares of overall mining costs (Grey 1993).
Figure 2.2. Surface Mine Showing Drag Line and Overburden
Source: U.S. EPA 1997
In open-pit mining, topsoil is the natural soil overlying the pit outline, while overburden includes material
lying between the topsoil and the uranium ore deposit. In more recent open-pit operations, soil is removed
and stockpiled for later site reclamation (i.e., restoration). Overburden is removed using scrapers,
mechanical shovels, trucks, and loaders. In some cases, the overburden may be ripped or blasted free for
removal. Overburden forms the largest volume of waste, is generally lowest in naturally radioactive
elements, and is not as enriched in uranium as protore. Protore is often stockpiled at the mine site as well,
2-5

-------
and is much higher in radionuclide or heavy metal content than overburden or soil
Once the ore body is exposed, radiometnc probing is used to define the exact extent of the ore body. Ore,
protore, and low-grade mineralized rock are outlined, and plans are developed for mining and stockpiling
them. Many times parts of an ore body delineated by drilling cannot be economically mined by open-pit
methods. Where parts of the deposit lie adjacent to the bottom of the planned pit, underground mines may
be developed from the pit bottom to recover these ores. Often waste material, including overburden, is
returned to mined-out areas during mining to reduce hauling costs
Figure 2.3. Surface Mine
This figure shows a surface mine operation in Nevada.
Source: U.S. EPA RCK4 Program
"Rim stripping" was a technique applied in areas of the Colorado Plateau. In this type of open-pit mining,
the ore body occurred at or near the surface along the edge (or rim) of a canyon. Miners would strip the
shallow overburden from the deposit and generally drop the waste material down the adjacent canyon
wall. In practice, this mining resembles strip mining for coal in the eastern United States. Rim stripping
was generally limited to the edge of the canyon because the overburden grew thicker farther away from
the rim.
Underground Mining
Deeper uranium ore deposits require underground mining by one of several excavation techniques,
including:
•	longwall retreat (a method of underground mining in which the ore bearing rock is removed in
one operation by means of a long working face or wall; the space from which the ore has been
removed either is allowed to collapse, or is completely or partially filled with stone and debris);
•	room and pillar (a conventional method of mining in which natural pillars are left unmined for
support between the mined rooms); and,
•	panels (a method of mining whereby the workings of a mine are divided into sections, each
surrounded by solid strata with only necessary roads through the rock barrier).
2-6

-------
The mining method of choice depends on several factors, including the size, shape, depth, and grade of
the ore body, the stability of the ground, and economics (Grey 1993). For small ore bodies near the
surface, miners may use:
•	adits;
•	inclines (a slanting shaft from the surface into the underground mine); or,
•	small shafts to reach and remove ore.
Larger, deeper deposits may require one or more vertical concrete-lined shafts or declines large enough
for motorized vehicles to reach the ore. Stopes (an underground excavation from which ore has been
removed in a series of steps) reaching out from the main shaft provide access to the ore.
Ore and waste rock generated during mining are usually removed through shafts via elevators, or carried
to the surface in trucks along declines. Because of the high costs of removing such materials, some waste
rock may be used underground as backfill material in mined-out areas. As with surface mining,
radioactive waste rock in underground mining is generally considered to be TENORM. The extracted ore
is stockpiled at the surface or trucked directly to a processing mill, which may be on site or at some
centralized location. Figure 2.4 is a diagram of an underground uranium mine with room and pillar
excavation.
Figure 2.4. Diagram of Room and Pillar Underground Mining
This figure shows a simplified diagram of a room and pillar underground mining operation. Main
vertical shafts connect with underground "rooms " that have been excavated using unmined rock columns
as support pillars. Rail cars move ore and waste through the mine.
Floor

' Pillar
Floor
Source: U.S. EPA (1997)
2-7

-------
Unconventional Mining Methods
Open-pit and underground mining methods, both of which rely on physical extraction to obtain raw
uranium ore, are commonly referred to as conventional mining methods. The reliance on chemical or
other means to extract uranium are referred to as unconventional mining methods, even though they may
have been used as extraction processes for decades. The sections which follow describe the heap leaching
and ISL extraction processes.
Heap Leaching
As this is an extraction process, heap leaching is regulated by the NRC or its Agreement States; the waste
rock is considered byproduct material (see Appendix VI). Ore that is removed from open-pit and
underground mining operations undergoes further processing to remove and concentrate the uranium; the
heap leaching may be located near the mine site. Ore is crushed in a large mill, grounded to sand
consistency, and mounded above grade on a prepared pad, usually constructed of clay, coated concrete, or
asphalt. A sprinkler system, positioned over the top, continually sprays leach solution over the mound. For
ores with low lime content (less than 12 percent), an acid solution is used, while alkaline solutions are used
when the lime content is above 12 percent. The leach solution trickles through the ore and mobilizes
uranium, as well as other metals, into solution. The solution is collected at the base of the mound by a
manifold and processed to extract the uranium. Figure 2.5 below provides an illustration of the process.
Heap leaching was used mostly on an experimental basis in the 1970s and 1980s, but is generally not in use
in the U.S. today.
2-8

-------
Figure 2.5. Illustration of Heap Leaching Process
In this illustration, leaching solutions (either acidic or alkaline) comprising the lixiviant are sprinkled on
crushed ore mounded on a liner or leaching pad. Uranium bearing fluids collect by gravity on the bottom of
the pile and drain into a pit (or pregnant pond): the fluids are then piped or transported to a mill for further
extraction and turned into yellow cake.
Solution Sprinklers

Pregnant Pond
Leaching Pad
t
/
Uranium
Mill
Lixiviant
Yellowcake
Source: EPA
In Situ Leaching (Solution Mining)
Since this is also an extraction process, ISL is regulated by the NRC or its Agreement States; the waste
materials and fluids are considered byproduct material (see Appendix VI). However, EPA standards and
requirements for uranium extraction facilities developed under UMTRCA, as well as requirements of
EPA's Underground Injection Control (UIC) program are applicable to ISL facilities (See Appendix VI
for more information). ISL operations are discussed here to provide a more complete representation of the
impacts from uranium production.
ISL is used when specific conditions exist, for example:
•	The ore is too deep to be mined economically by conventional means;
•	The uranium is present in multiple-layered roll fronts that may be offset by faulting;
•	The ore body is below the water table;
•	Considerable methane and hydrogen sulfide are associated with the ore;
•	The ore grade is low, and the ore body is too thin to mine by conventional means;
•	A highly permeable rock formation exists in which uranium can be economically produced.
2-9

-------
In this method of extraction, uranium ores are leached underground by the introduction of a solvent
solution, called a lixiviant, through injection wells drilled into the ore body. The process does not require
the physical extraction of ore from the ground. Lixiviants for uranium mining commonly consist of water
containing added oxygen and carbon dioxide or sodium bicarbonate, which mobilize uranium. The
lixiviant is injected, passes through the ore body, and mobilizes the uranium. The uranium-bearing
solution is pumped to the surface from production wells.
The pregnant leach solution is processed to extract the uranium, usually by ion exchange or by solvent
extraction. The ion exchange process employs a resin that, once fully saturated with uranium, is flushed
with a highly concentrated salt (e.g., sodium chloride) solution. This reverses the exchange process and
releases uranium into the solution. The uranium solution is then sent to another process for concentration,
precipitation and drying, as yellowcake. The solvent extraction process relies on unmixable properties
between the pregnant leach solution and (uranium) solute. Normally, the solvents are organic compounds
that can combine with either cationic or anionic solutes. For example, anionic solutions include amine
chains and ammonium compounds, and cationic solutions are phosphoric acid-based. Figure 2.6 shows a
simplified version of the ISL process.
Figure 2.6. Illustration of ISL Process
This figure shows a simplified version of how ISL solution mining works. Lixiviant is injected
into the ground through a well on the left and far right, the fluid flows underground dissolving
uranium and carrying it in solution until it reaches a production well in the center. The fluid
carrying dissolved uranium is returned to the surface from the production well, then is piped
off to a production facility for refinement into yellowcake.
Injection Well
Lixiviant In
Production Well
Uranium, Lixiviant,
Groundwater Out
Injection Well
Lixiviant In
Uranium Ore Zone
Idealized ISL Operation
Source: Modified afterANAWA : httv://www.ancrwa.ore.au'minins/isl-diaeram.hlml
When the ISL process is completed, the ore body and aquifer are placed in a restoration phase, as required
by mine permits, NRC and Agreement State regulatory programs. Typically, the aquifer must be restored
to background or EPA drinking water maximum contaminant limit levels where possible or practical, or
to Alternate Concentration Limits (ACLs) in terms of the presence of metals, organics, pH level, and
radioactivity, approved by the NRC and its Agreement States, with EPA concurrence. Therefore, in some
cases, restoring it to the pre-operation level does not necessanly make it potable. EPA groundwater
protection standards issues under authority of UMTRCA are required to be followed by ISL licensees of
the NRC and its Agreement States. In addition to those requirements, ISL operators must apply for UIC
permits from EPA. Through the UIC aquifer exemption process, EPA and its Delegated States determine
if an aquifer or part of an aquifer is exempt from protection as an underground source of drinking water
2-10

-------
during the mining process. Approval of this exemption is necessary before a UIC permit may be issued
for ISL mineral extraction wells. EPA requires, however, that non-exempted groundwater sources be
protected from contamination.
Uranium Milling
While not a central focus for this report, information is provided below primarily from U.S. EPA (1995a)
on the uranium milling process; for more detailed discussions on the milling process, the reader is
referred to that report. Licensed by the NRC under 10 CFR Part 40, Appendix A, mills process source
materials (see Chapters 1 and Appendix VI) from conventional uranium mines and occasionally from
other industrial activities or mines. Uranium mills have typically been associated with specific mines or
functioned as custom mills, serving a number of mines. Most available information on milling operations
was written when a dozen or more were operational, therefore the following discussions may not
precisely describe milling activities being conducted at present, or in the future. The chemical nature of
the ore determines the type of leach circuit required and, in turn, the extent of grinding of ore received
from a mine.
The initial step in conventional milling involves crushing, grinding, and wet and/or dry classification of
the crude ore to produce uniformly sized particles. Ore feeds from crushers to the grinding circuit where
various mechanical mills grind the rock to further reduce the size of the ore. Water or lixiviant is added to
the system in the grinding circuit to facilitate the movement of solids, for dust control, and (if lixiviant is
added) to initiate leaching (U.S. DOI 1980). Screening devices are used to size the finely ground ore,
returning coarse materials for additional grinding. The slurry generated in the grinding circuit contains 50
to 65 percent solids. Fugitive dust generated during crushing and grinding is usually controlled by water
sprays or, if collected by air pollution control devices, recirculated into the beneficiation circuit. Water is
typically recirculated through the milling circuit to reduce consumption (U.S. EPA 1983d).
After grinding, the slurry is pumped to a series of tanks for leaching. Two types of leaching have been
employed by uranium mills, acid and alkaline. A solvent (lixiviant) is brought into contact with the
crushed ore slurry. The desired constituent (uranyl ions) is then dissolved by the lixiviant. The pregnant
lixiviant is separated from the residual solids (tails); typically the solids are washed with fresh lixiviant
until the desired level of recovery is attained. The uranyl ions are recovered (stripped) from the pregnant
lixiviant. The final steps consist of precipitation to produce yellowcake, followed by drying and
packaging (Pehlke 1973). The stripped lixiviant may be replenished and recycled for use within the
leaching circuit or as the liquid component in the crushing/grinding operation. Ultimately, the solids may
be washed with water prior to being pumped to a tailings pond; this wash serves to recover any remaining
lixiviant and reduce the quantity of chemicals being placed in the tailings impoundment. Wash water may
be recycled to the lixiviant or to the crushing and grinding circuits.
Operational mills currently function independently of specific conventional mines and generate materials
that are, in most cases, unique from those generated at the site of extraction. Under UMTRCA, source-
handling licenses place specific requirements on the disposal of radioactive wastes; the design and
construction of tailings impoundments address NRC requirements for permanent storage of these wastes.
Radionuclide-containing wastes generated by ISL operations are typically shipped to tailings
impoundments at mill sites. Figure 2.7 shows the general physical layout of a typical uranium mill.
Information on statutory requirements for closure and reclamation of abandoned and inactive uranium
mills can be found in Appendix VI, characteristics of mill tailings in Chapter 3, and reclamation
2-11

-------
procedures for closed mills and mill tailings impoundments can be found in Chapter 4. Mills in operation
and inactive are discussed below.
Figure 2.7. Generalized Uranium Mill Physical Layout
This figure shows how a uranium mill is physically set up to crush raw ore
into particles amenable to chemical treatments for extracting uranium.
Amnonia l_J tVacipitaliai
Emractior Crcuit \\ |	M H
hiHralion
Loachhg
Sdl Soluticrt
Clas&ifpBfS (Washing)
SlfippriuCiretil
Sampling
Yvicw Cake
Tailinfls
Source: U.S. DOE/EIA, httv://www.eia.doe.em'/cneaf/miclear/vaee/uran enrich fiiel/iiraniiimmill.htnil
The Uranium Industry Today
Due to worldwide oversupply of uranium, and dearth of new U.S. nuclear plants, the U.S. uranium
mining industry was depressed from the early 1980s until about 2003, when only a few mines remained in
operation. In 1981, the United States produced nearly 14,800 metric tons of oxide of uranium (U308)
equivalent at an average price of over $34 per pound. U308 equivalent production in 1991 was
approximately 3,600 metric tons sold at an average price of $13.66 per pound. While it had decreased to
less than $8 per pound in 2000, by 2004, due to increasing demand, the price of uranium increased
substantially. In early 2006, it had increased to approximately $40 per pound. These fluctuations in price
affect the numbers of operating mines and mills in the country, and the methods of extraction used.
The employment structure in the uranium industry has significantly changed since the mid-1970s, when
nearly 60 percent of the uranium industry labor force was devoted to uranium mining and production.
This fraction steadily declined until recently, when only about 25 percent of the employment was related
to mining (including ISL) and almost one-half of that was associated with reclamation of past production
facilities. The industry experienced the highest level of employment in 1979 with 21,500 workers. In
1981 employment was about 13,600, and in 2000 the work force was down to 627 workers (U.S.
2-12

-------
DOE/EIA 2001). Due to increased demand for uranium which resulted in higher prices, steady increases
were seen in employment and production of uranium commencing in 2004.
The U.S. Department of Energy's EIA reports that in 1992, 51 person-years were expended in
exploration, 219 in mining activities, 129 in milling operations, and 283 in processing facilities (U.S.
DOE/EIA 1992, 1993). By 2000, one person-year was expended in exploration, 157 in mining, 106 in
milling, and 137 in processing (U.S. DOE/EIA 2001); the remainder (226 person years) were involved in
site reclamation. It is reported in the "Domestic Uranium Report" (U.S. DOE/EIA 2005b) released by the
Department of Energy in August, 2005, that employment in the U.S. uranium production industry totaled
420 person-years, an increase of 31 percent from the 2003 total. Reclamation employment increased three
percent. Wyoming accounted for 33 percent of the total 2004 employment, while Colorado and Texas
employment almost tripled since 2003. Overall, $86.9 million went to drilling, production, land
exploration and restoration activities in 2004.
A total of 17 uranium mines were operational in 1992: five conventional mines (both underground and
open-pit), four ISL and eight reported as "other" (mill tails recovery operations, mine water extraction, or
from low-grade stockpiles). Uranium in 1992 was also produced to a limited extent as a side product of
phosphoric acid production at four sites (U.S. DOE/EIA 1993). By 2002, production had been reduced to
three ISL operations and one underground mine (U.S. DOE/EIA 2003a). The ISL sites were located in
Wyoming and Nebraska. A number of mines were closed and inactive with the possibility of reopening
should the price of uranium increase in the future. In 2002, only 2.4 million pounds (-1090 MT) of U308
were produced domestically by: ISL operations, processing of waste mine-water, or reclamation and
restoration activities at closed ISL sites.
The uranium production industry had a turnaround in 2004. An increase in all aspects of the industry was
noticed for the first time since 1998. This included drilling, mining, production and employment. In 2004
(latest statistics available) 2.5 million pounds (~1135 MT) of U3Os were mined in the U.S. which was 11
percent higher than the previous year (U.S. DOE/EIA 2005a). A new underground mine and a new ISL
mine started in 2004. Total U.S. production of yellowcake (uranium concentrate) was 2.3 million pounds
(-1045 MT) which was 14 percent higher than the production in 2003. Table 2.2 below provides U.S.
uranium concentrate production by quarters.
2-13

-------
Table 2.2. U.S. Uranium Mine Production: 2000-2005
This table shows Total Production of Uranium Concentrate in the United States, 2000 -2005
Production is reported in pounds U3Os, metric tons are included in parentheses

2000
2001
2002
2003
2004
2005p
1 st Quarter
1,018,683
(462 MT)
709,177
(322 MT)
620,952
(282 MT)
E 400,000
(181 MT)
E 600,000
(272 MT)
708,980
(322 MT)
2nd Quarter
983,330
(446 MT)
748,298
(339 MT)
643,432
(292 MT)
E 600,000
(272 MT)
E 400,000
(181 MT)
630,057
(286 MT)
3rd Quarter
981,948
(445 MT)
628,720
(285 MT)
579,723
(263 MT)
E 400,000
(181 MT)
588,738
(267 MT)
585,925
(266 MT)
4th Quarter
973,585
(442 MT)
553,060
(251 MT)
E 500,000
(227 MT)
E 600,000
(272 MT)
E 600,000
(272 MT)
NA
Calendar-Year Total
3,957,545
(1795 MT)
2,639,256
(1197 MT)
E 2,344,107
(1063 MT)
E 2,000,000
(907 MT)
2,282,406
(1035 MT)
NA
P = Preliminary data.
E = Estimate - The 2003 and 1 st, 2nd, and 4th quarter 2004 production amounts were estimated by rounding to the nearest
200,000 pounds to avoid disclosure of individual company data. The 4th quarter 2002 production amount was estimated by
rounding to the nearest 100,000 pounds to avoid disclosure of individual company data. This also affects the 2002 annual
production.
NA = Not Available.
Notes: Totals may not equal sum of components because of independent rounding or reporting methods mentioned previously.
Next update is approximately 45 days after the end of the fourth quarter 2005.
Source: Modified from U.S. DOE/EIA (2005b): Form EIA-858, "Uranium Industry Annual Survey."
Only 16 percent of all uranium purchased by U.S. utilities in 2000 was domestically produced (U.S.
DOE/EIA 2000a). According to surveys of owners and operators of U.S. civilian nuclear power reactors,
future deliveries of U308 for 2001-2010 would amount to 116.5 to 179.0 million pounds (53 to 81
thousand MT). It was also estimated that foreign suppliers would provide 54 percent of the maximum
projected deliveries through 2010.
U.S. non-conventional extraction facilities are primarily ISL plants. The decision to reopen a plant
primarily depends upon the prevailing economics and market conditions. A few ISL operations are
remaining open or inactive today, opening intermittently as the price of uranium continues to fluctuate.
The only mills currently operating are Cotter Corporation mill in Colorado and International Uranium's
White Mesa mill in Utah, while the Kennecott Sweetwater Wyoming mill is inactive, and the Plateau
Resources mill in Utah is amending its license to operations (U.S. DOE/EIA 2005a).
Recent power uprates3 and upgrades to U.S. nuclear plants have had the equivalent impact of nineteen
new reactors starting operation, and other countries have indicated interest in building new plants as well.
Since most of the demand for uranium originates from the commercial sector (nuclear power plants), and
that demand is increasing, it is likely it will affect uranium market demand and supplies (Wyoming
Mining Association 2004).
3 The process of increasing the maximum power level at which a commercial nuclear power plant may operate.
2-14

-------
U.S. uranium reserves must also be taken into consideration, because changes in the price of uranium may
make them important resources in the future. Figure 2.8 provides a map with locations of reserve areas,
while reserve estimates are included in Table 2.3. Reserve estimates represent the quantities of uranium
(as U308) that occur in known deposits, such that portions of the mineralized deposits can be recovered at
specific costs under current regulations using state-of-the-art mining and milling methods (U.S. DOE/EIA
2004). At of the end of 2004, EIA estimated uranium reserves in the $30- and $50-per-pound categories
were 265 and 890 million pounds (120 and 400 thousand MT), respectively. Underground mine reserves
accounted for about one- half of the total reserves in each cost category. The reserve decreases are based
on 2003 mine production of uranium and reflect the combined effects of depletion and erosion of in-place
ore quantities remaining at year-end. Figure 2.9 below shows the status of mines, ISL operations, and
mills in the U.S. as of late 2005.
2-15

-------
Figure 2.8. Major U.S. Uranium Reserve Areas
This map shows major areas of remaining uranium reserves, all in the western U.S.
Major U.S. Uranium Reserves
Spokane
Powder River
Wind River Basin
\ Basin \
Northwest
Nebraska
Front
Range
Paradox-]
... Basin J
Tallahassee v
Creek
Marshall
Tafg;
Grants
Mineral
_ Belt
Texas
Gulf
Coast
^ CT Alaska
Hawaii
¦Sources Based on L S Department of Energy, Grand Junction Project Office (GJPO). National Uranium Resources
Evaluation, Interim Repot („une 1979) Figure 3.2. and GJPO data f.les.
Source: From DOE/EIA httv://www. eia.doe.zov/cneaf/nuclear/vaze/reserves/uresarea.html)
2-16

-------
Table 2.3. Uranium Reserves of the United States as of December 31, 2003.
This table developed by the Energy Information Administration of DOE provides
a breakdown of uranium reserves by mining method based on price
of uranium of $30 per pound and $50 per pound.
U.S. Forward-Cost Uranium Reserves by Mining Method, December 31,2003

Forward-Cost Category

$30 per pound
$50 per pound
Mining
Method
Ore in
million tons
(million
Metric Tons)
Grade3
(percent
u3o8)
U3Os in
million
pounds
(Metric Tons)
Ore in million
tons (million
Metric Tons)
Grade3
(percent
u3o8)
u3o8
in million
pounds
(Metric tons)
Underground
25 (23)
0.272
138 (62,600)
143 (130)
0.163
464 (210,500)
Open-pit
10(9)
0.139
29 (13,150)
163 (148)
0.079
257(116,600)
In Situ
Leaching
39 (35)
0.127
98 (44,450)
116(105)
0.071
165 (74,800)
Otherb
< 1 (0.9)
0.265
<1(<453)
3 (2.7)
0.059
4(1,814)
Total
74 (67)
0.178
265 (120,200)
424 (385)
0.105
890 (404,000)
"Weighted average percent U308 per ton of ore.
bIncludes low grade material and miscellaneous.



Notes: Uranium reserves that could be recovered as a byproduct of phosphate and copper mining are not included
in this table. Reserves values in forward-cost categories are cumulative: that is, the quantity at each level of
forward-cost includes all reserves at the lower costs. Totals may not equal sum of components because of
independent rounding.
Sources: Estimated by Energy Information Administration, Office of Coal, Nuclear, Electric and Alternate Fuels,
based on industry conferences; U.S. Department of Energy, Grand Junction Office, files; and Energy Information
Administration, Form EIA-858, "Uranium Industry Annual Survey," Schedule A, Uranium Raw Material
Activities (1984-2002) and Form EIA-851 A, "Domestic Uranium Production Report" (2003).
Source: Modified from U.S. DOE/EIA (2005c), http.V/www. eia.doe.zov/cneaf/nuclear/vaze/reserves/uresmine.html
2-17

-------
Figure 2.9. Status of Mines, ISL Operations, and Mills in the U.S. as of November 2005
This figure shows the locations and operating status of uranium operations in the U.S.
as of the end of2005. An increase in the price and demand for uranium resulted
in the re-opening of some conventional uranium mines and ISL operations,
and decisions to re-start some sites which were undergoing closure.
Approximate Locations of Operating, Standby, or Pending Uranium Mills and Mines
Legend
x Uranium Mines
+ Uranium Milts
Source: U.S. EPA.
2-18

-------
Chapter 3. Volume and Characteristics of Uranium Mine Wastes
Uranium has been found and mined in a wide variety of rocks, including sandstone, carbonates1, and
igneous (volcanic-derived) rocks (see Chapter 1). This variety of source material, the type of mine and
extraction operation (see Chapter 2), local climate, soil, and topography can lead to a wide range of
differing physical and chemical properties in waste materials. Waste characteristics are important because
they are used to model and assess the environmental impacts and public health risks of radionuclides,
heavy metals, and other chemicals associated with mine sites, and the implications for site cleanup. While
this chapter discusses wastes from conventional mining, solution extraction, and milling of uranium, a
principal focus of this report is TENORM from conventional mining, and in particular, wastes from
abandoned mines that have not been reclaimed, or which may need future reclamation.
When uranium mining first started, most of the ores were recovered from deposits located at, or near the
surface of the land. Ores were often exposed at the surface, and underground mines followed mineralized
zones directly into the subsurface. Thin overburden over deeper parts of the ore body adjacent to the
surface exposure would be removed to create shallow open-pits. As easily accessible ore deposits became
depleted, mining had to be performed at increasing depths by either open-pit or underground methods. To
reach deeper deposits, the industry had to move larger quantities of topsoil, overburden, plus barren or
waste rock.
The amount of overburden that may be removed during open-pit mining is a complex function of the
depth to the ore body, the grade and thickness of the ore bearing zone, the price of uranium, and the costs
of moving the overburden and site restoration. The costs of processing ore at mills also influence the
overall economics of underground and surface mining. These costs have steadily declined, and have
lowered the ore grade that is economically feasible to extract (Otton 1998). Thus, while an ore grade of
0.15 percent was often ignored in the early mining years, newer, more efficient ore extraction techniques
have targeted ore grades as low as 0.03 percent, though that is an extreme case. The NRC has established
a level of 0.05% uranium content as a threshold for regulation as source material under its regulations 10
CFR 40.4; NRC considered technology and economics in selecting the threshold.
Waste terms that will be used in the discussions from Chapters 3 through 5, and the Appendices, are listed
in Table 3.1 and are defined below in the text, as well as the Glossary (Appendix I). Wastes considered to
be TENORM, versus those subject to NRC or its Agreement States' byproduct regulations are also
identified.2
While there is a limited discussion in this chapter on environmental fate and transport of uranium
associated with mine wastes, the reader is referred to previous EPA reports on uranium geochemistry
(U.S. EPA 1999b and 1999c). The geochemistry of uranium can be extremely complicated, however,
those documents provide an overview of important aqueous and solid phase parameters, as well as
1	A sediment or sedimentary rock formed by the organic or inorganic precipitation from aqueous solution of
carbonates of calcium, magnesium, or iron; e.g., limestone and dolomite.
2
Some materials that are wastes within the plain meaning of the word are not "solid wastes" as defined under the
Resource Conservation and Recovery Act and thus are not subject to regulation under that law. These include, for
example, mine water or process wastewater that is discharged pursuant to a National Pollution Discharge
Elimination System permit. It is emphasized that any questions as to whether a particular material is a waste at a
given time should be directed to the appropriate EPA Regional office.
3-1

-------
discusses general geochemistry, aqueous speciation, precipitation and co-precipitation, and other
important geochemical aspects.
Data obtained from many older scientific studies referenced in this report may have only been originally
provided in English measurement systems. Conversions are made in the text and tables of this report;
however, the reader should understand that the converted numbers may be rounded. If available in the
original studies cited in this report, information on uncertainties and precision of measurements and data
will be included. However, many of these studies were conducted during a time when reporting
uncertainties and precision of data were not standard practice. While data quality is a vital aspect of
scientific and technical endeavor, we regret that the boundaries of uncertainty and accuracy of data
presented may not have been cited in many of the original studies available for this study.
Table 3.1. Uranium Mine and Operations Wastes
The following mine wastes are generated by conventional uranium mines, heap leach and
ISL operations, and uranium mill operations. They are the principal wastes
discussed in Chapters 3 through 5, and the Appendices of this report.
Not all wastes listed may be radioactive at all uranium mines or operations, though if they are,
they may be subject to regulatory control according to the column they are listed under.
Wastes Generated by Uranium Mines and Extraction Operations
Conventional Open-Pit and Underground
Mines (TENORM Wastes—EPA, Federal
Land Management, and Tribal and State
Agencies Jurisdiction)
Heap Leach and ISL
Operations (Byproduct Wastes
subject to NRC and Agreement
State Jurisdiction)
Uranium Mills (Byproduct
Material Subject to NRC or
Its Agreement State
Jurisdiction)
Pro tore*


Overburden*


Barren or Waste Rock*


Top Soils*
Top Soils*

Drill Cuttings* and Drilling Wastes
Drill Cuttings* and Drilling Wastes

Wastewater
Wastewater
Wastewater
Wastewater Treatment Sludge
Wastewater Treatment Sludge
Wastewater Treatment Sludge
Lab Wastes
Lab Wastes
Lab Wastes
Pit Water*


Mine Water
Produced Water


Leachate


Liquids from aquifer restoration

Evaporites
Evaporites
Evaporites


Mill Tailings
Refuse (if radioactive)
Refuse (if radioactive)
Refuse (if radioactive)
Source: U.S. EPA (1983a,b,c; 1995), U.S. NRC (2004, 2003)
*Term was previously defined in Chapter 1.
Terms in Table 3.1 not previously defined:
•	Drilling wastes—Wastes associated with a drillhole operation at a mine or extraction facility that
are not considered cuttings or cores. May include drill muds or other drilling fluids, sludges, or
evaporation products collected in excavated pits from wastewater produced during drilling.
•	Wastewater— The spent or used water from a mine that contains dissolved or suspended matter.
•	Wastewater Treatment Sludges—Sludge derived by the treatment of wastewater to remove
suspended solids, metals, radionuclides or other pollutants from mine generated wastewater.
•	Lab Wastes—Wastes of any kind generated by a laboratory, usually on-site, analyzing rock,
3-2

-------
sediment, water or other samples obtained at the mine or extraction facility, or its vicinity.
•	Mine Water— Water or brine which collects in mine workings, both surface and underground, as
a result of inflow from rain or surface water and of groundwater seepage.
•	Produced Water— Water from ISL operations extracted from the subsurface with dissolved
minerals. It may include water from the reservoir, water that has been injected into the formation,
and any chemicals added during the production/treatment process.
•	Leachate—A solution obtained by leaching; e.g., water that has percolated through soil
containing soluble substances and that contains certain amounts of these substances in solution.
•	Evaporite—A chemical sediment that precipitates when the salty water in which it had dissolved
evaporates
•	Refuse—Solid waste. Insoluble materials ranging from municipal garbage to industrial wastes that
contain complex and sometimes hazardous substances. Solid wastes also include sewage sludge,
agricultural refuse, demolition wastes, mining equipment and mining residues. Solid waste also
refers to liquids and gases in containers.
•	Mill Tailings— Residue of raw material or waste separated out during the processing of uranium
mineral ores. Byproduct material in accordance with the AEA.
Waste Footprint of a Mine
Though all mining methods produce waste products, the volume, location, state, and environmental
impacts of these wastes can be vastly different. For example, open-pit and underground mining
techniques, known as conventional mining, generally produce large amounts of solid waste, while ISL
methods produce only small amounts of solid waste, but result in more significant amounts of liquid
waste that can spread across a very large area. As noted previously and in Appendix VI, ISL operations
and liquid wastes generated by those activities, and their environmental impacts are regulated by the NRC
or its Agreement States. In general, states, Tribes, and federal land management agencies are responsible
for regulating the disposal of solid and other waste generated on their lands by mining operations.
The overall footprint of a mine area may be described as the areal extent of land physically disrupted by a
mine operation. The footprint can vary significantly depending on the amount of waste left on site, and
not necessarily to the amount of oxide of uranium (U308) produced. The typical waste footprint of
uranium mining operations has changed since the late 1940s—from very small, to very large, and then
smaller again.
Because the nature of mining changed over the years, waste generation also changed. This change in
waste generation largely reflects changes in the scope of mining operations and the technology employed.
When early mining efforts in the 1940s and 1950s were dominated by small operations, sometimes
consisting of a single prospector/miner, thousands of mines were developed from ore bodies of the
Colorado Plateau, sometimes as small as a single rich uraniferous vein or lens weighing as little as a few
metric tons. The early small mining endeavors generated small quantities of waste, because miners found
and exploited only deposits near the surface, and they had limited capacity to move large quantities of
material. These small quantities of waste typically were discarded within several to 100 yards (about
several to 100 meters) of the mine opening or pit.
As many mining properties both on the Colorado Plateau and in areas in other states, such as Texas and
Wyoming, proved to have much larger ore bodies, more expansive mining operations developed at these
sites. When larger companies came on the scene in the 1950s and 1960s, they brought technologies and
3-3

-------
manpower to exploit larger ore bodies, deeper in the ground, and of lower grade. These large
conventional operations generated correspondingly large waste streams, and the overall site size expanded
significantly.
Major open-pit mines tend to disturb large surface areas from the extent of both the pit and the mine
waste areas. Generally, tens to hundreds of acres may be covered by stored overburden. For example, an
aerial survey conducted of eight surface mining sites in New Mexico and two in Wyoming indicated that
disturbed areas varied from just under three to 380 acres (approximately one to 154 hectares), with an
average of 110 acres (approximately 45 hectares) per site (U.S. EPA 1983b). At some sites, as mining
progressed, the overburden was used to backfill mined-out areas of the open-pit in anticipation of later
reclamation. Most of the older surface mines (pre- to mid-1970s) were not backfilled during mining
operations, while some of the more recent mining included modest backfilling operations.
The surface area affected by major underground mining activities generally involves less than about 50
acres (20 hectares). Mine maps often show extensive underground mining following ore zones with only
small piles of waste rock at the mouth of the mine's entry. For example, an aerial survey conducted of
nine underground mining sites located in New Mexico and one in Wyoming indicated that disturbed
surface areas varied from just over two to 42 acres (one to 17 hectares), with an average of 30 acres
(approximately 12 hectares) per site (U.S. EPA 1983b). However, the underground mine works (or
tunnels) may extend laterally for more than a mile in several directions. The Orphan Mine (see Appendix
III) is an underground mine with a surface loading area clearing less than five acres (two hectares), and a
cliffside mine opening covering similar acreage, where spoil rock and a collapse hole over the abandoned
tunnels are the principal observable features.
When economics and technological advances in the 1980s prompted the increased use of ISL as an
extraction method, the volume of solid waste generated dropped dramatically. While not a surface mining
method, for comparison purposes only, the total areal extent of an ISL operation may be large, depending
on how drill holes are situated, and how extensive evaporation ponds are. To be cost-effective, ISL
requires large production areas or zones, but the surface facilities may take up only a small portion of the
acreage. Table 3.2 presents the general features of several ISL operations (U.S. EPA 1993b). The number
of production areas ranges from one to seven and can include a large number of wells, ranging from 200
to over 10,000, while aquifers are often located both above and below production zones.
3-4

-------
Table 3.2. Profile of Several Texas ISL Uranium Mining Operations
The acreage of ISL operation properties varies from about 200 to over 6,000 acres (81 to 2,430
hectares). The actual acreage covered by well fields may be significantly less (Kennecott Uranium
Company 2004). ISL operations are not a surface mining method, though the production facilities
may produce from large land holdings, and are regulated by the NRC or its Agreement States.
All the facilities included below are in Texas.
Mine Name
Acreage
Benavides
170
O'Hern
270
Zamzow
316
Pawnee
320
West Cole
680
West Clay
884
Lamprecht
957
Boots Brown
1,025
Pawelek
1,698
Holiday
2,000
El Mesquite
2,200
Rosita
2,208
Burns Moser
2,262
Kingsville Dome
2,315
Trevino
5,750
Talan Gara (renamed
6,272
Palangana)

Source: U.S. EPA 1993b
Mine Waste Volumes
Conventional Open-Pit and Underground Mines
In open-pit mining, as described in Chapter 2, a pit is excavated to expose the uranium deposit. After the
topsoil is removed and stockpiled nearby, the overburden is removed and trucked to a nearby mine waste
area. Occasionally, dikes and ditches are constructed around these waste piles to collect runoff and divert
it to sedimentation ponds.
While underground mining is much less disruptive to surface terrain than open-pit mining and produces
less waste, that waste may have higher average radioactivity. In underground mining, access to the ore
body is gained through one or more adits or vertical shafts, generally sunk to a slightly greater depth than
the ore body, or through inclines and declines, all of which are cut through barren or waste rock. Mining
carefully follows the ore body using stopes and tunnels to minimize the amount of waste material that
must be moved. When mining in larger deposits, other mining methods may be used, for example, the
room and pillar or block caving techniques. The block caving technique forces a large section of ore
deposit to fall into a man made cavern. The ore is broken by drilling and blasting, and ore and waste rock
are moved out of the mine to the surface through tunnels, inclines, and shafts. The barren or waste rock is
removed to a spoils area that may be surrounded by a ditch to contain water runoff.
3-5

-------
Data from the U.S. Department of Energy's (DOE's) Energy Information Administration (EIA) indicate
that before 1980 about one-third of conventional uranium mines were small with less than 100 metric tons
of uranium ore production, about one-fifth to one-quarter of the mines were moderate sized with between
100 and 1,000 metric tons of production, and about one-third of the mines were large and had production
between 1,000 and 100,000 metric tons of production (U.S. EPA 1983b). Only about five percent, or
150-220 mines, were extremely large mines producing more than 100,000 metric tons of ore. When
combined with information on the relationship between ore production and waste, it is possible to
estimate the amounts of waste for the different production categories.
To calculate an estimate of waste generation, waste-to-ore ratios are needed for different sizes of mines.
Throughout the 1950s, 1960s, and 1970s, open-pit mining on the Colorado Plateau was characterized by
small to moderate-sized operations with highly variable waste-to-ore ratios, but the data on these mines
are not good and waste estimation is difficult. The higher the waste-to-ore ratio, the more waste that is
generated per ton of ore extracted. Large open-pit mines in Wyoming and New Mexico usually had lower
waste-to-ore ratios, and in Texas moderate to large open-pit operations were found with generally high
waste-to-ore ratios. In the late 1970s (Bohert and Gerity 1978; Facer et al. 1978) and early 1980s, waste-
to-ore ratios for the largest mines appear to have peaked at an average of about 30:1 (30 times as much
waste as ore produced). As the price of uranium decreased in the early 1980s, only the more efficient
open-pit operations remained in production, and the waste-to-ore ratios also decreased for the period 1984
to 1992.
For underground mines, waste-to-ore ratios generally range from 20:1 to 1:1, with an average ratio of
about 9:1 (nine times as much waste as ore produced) (U.S. EPA 1983b). As with surface mining, this
ratio has also changed over the years with increased mining efficiency, and selection of more
economically produced deposits such that the amount of waste decreased from a range of 5:1 until the
early 1970s, to about 1:1 by the late 1970s.
EIA historical records (Smith 2002) indicate that before 1980, a number of underground and surface
uranium mines generated less than 1,000 metric tons of ore with a ratio of waste to ore ranging from
about 10:1 to 30:1. Accordingly, a 1,000 metric ton mine might generate 10,000-30,000 metric tons
(3,500-11,000 cubic meters) of waste. With respect to the area covered by waste piles, for EIA's two
smallest production size categories, less than one-third of an acre would be expected to be covered by
waste piles 16 feet (five meters) high. Smaller mines could have a waste-to-ore ratio of 50:1. At 16 feet
(five meters), which is an average height for a waste pile, a small operation could produce waste covering
0.2-0.5 acres (0.08 to 0.20 hectares). Waste piles for small surface and underground mines were found to
cover 0.1 to five acres (0.04 to two hectares) (U.S. EPA 1983b).
To estimate the volume of waste that may have been generated, Otton (1998) conducted a study of mine
waste ratios for EPA. Table 3.3 presents the study results for surface and underground mining. Appendix
IV provides the basis for the estimates. Waste produced by open-pit mining is a factor of 45 greater than
for underground mining, based on their respective averages. For the range between the low and high
estimates, the factor is 190 for the low estimate and 80 for the high. Thus, the amount of overburden
generated from open-pit mines far exceeds that of underground mines.
3-6

-------
Table 3.3. Estimated Overburden Produced by Open-Pit and Underground Mining
The waste generated by open-pit mining is estimated to be 45 times greater than for underground mining.
Mining Method
Estimated Overburden Produced (MT)
Low Estimate
High Estimate
Average
Surface Mining
1,000,000,000
8,000,000,000
3,000,000,000
Underground Mining
5,000,000
100,000,000
67,000,000
Source: Otton 1998.
Waste Volumes at Sample Conventional Mines
Typically, the waste material is placed in piles that can be quite large, representing thousands to hundreds
of thousands of tons of material and covering a large area. The White King/Lucky Lass mines site (two
mines adjacent to one another—see Appendix III), now a Superfund site, had very large piles of waste
material and protore. At the White King Mine one (protore) pile covers approximately 17 acres (seven
hectares) with an average thickness of 20 feet (six meters), and a second (overburden waste) pile covers
approximately 24 acres (about ten hectares) with an average thickness of 15 feet (about five meters) (U.S.
EPA 2001a). Approximately 35,000 cubic yards (32,000 cubic meters, assuming 2,800 kg/m3 waste
material density due to the high concentration of denser uranium in the material)3 of soil outside the
perimeter of the White King piles were estimated to be elevated in radium (defined as > 5 pCi/g (0.185
Bq/g) Ra), along with 7,700 yards3 (7,040 m3) of soil outside the perimeter of the Lucky Lass piles.
The Jackpile-Paguate open-pit mine began production in New Mexico in 1953 and ceased in 1982. Table
3.4 demonstrates how the ratio of overburden to produced ore changes over the life of a mine. The mine site
contained 32 waste dumps and 23 protore dumps segregated according to grade. About 10.5 million metric
tons (MMTs) of protore were stored outside the pits, and another 4.5 MMTs were stored in dumps within
pits. The ratio of all waste to protore was about 24:1. About 92 MMTs of backfill, comprised of ore-
associated waste and some overburden, were returned to the pits during operations.
3 Density is an important factor in calculating the metric tons (weight per volume) of waste rock.
3-7

-------
Table 3.4. Changing Ratio of Overburden to Ore Over
Mine Life—Jackpile-Paguate Mine, New Mexico
The amount of mine waste increases over time relative to the amount ofproduced ore
in a large surface mine. Ore and overburden are report in metric tons (MTs).
Year
Ore Produced
(MTs)
Overburden
(MTs)
Mining Ratio
(overburden protore
rock: ore)
1953 - 1963
6,000,000
70,000,000
11.7:1
1953 - 1974
9,000,000
110,000,000
12:1
1953 - 1982
23,000,000
364,000,000
16:1
Sources: Kittel 1963; Graves 1974; U.S. BLM1986.
At the other end of the spectrum is the Canyonlands National Park in Utah (see Appendix III), where the
waste dumps for underground mines (most likely either exploration shafts or small mines) ranged from 35
to 800 yards3 (37 to 612 m3) (Table 3.5). Production data from these mines were unavailable. Figure 3.1
shows the outside of one of the mine openings.
Table 3.5. Mine Workings and Associated Waste Rock Volumes in Canyonlands, Utah
This table highlights the variety of waste dump sizes and lengths of entries for a series
of 12 closely located underground mines in Canyonlands National Park, Utah.
Workings vs.
Mine
Waste
1
2
3
4
5
6
7
8
9
10
11
12
Lateral
82
28
75
865
450
230
215*
188
20
70
40
235
workings
(25)
(9)
(23)
(264)
(137)
(70)
(66)
(57)
(6)
(21)
(12)
(72)
in feet












(meters)












Waste
120
-
-
800

470

220
35
165
100
400
in yards3
(92)


(612)

(359)

(168)
(27)
(126)
(76)
(306)
(meters3)












* Visual estimate of adit length. Remote workings are flooded 115 feet (35 meters) in from the portal.
Source: Burghardt et al. 2000.
3-8

-------
Figure 3.1. Mine Portal, Canyonlands National Park, Utah
Canyonlands, Utah, underground mine entr}> and the mine waste spoil pile located
on the canyon slope beneath. Note the coarse nature of materials
in the waste pile—boulders and cobbles, in addition to finer-grained materials.
Source: Photo courtesy of Utah Division of Abandoned Mine Lands Reclamation
ISL Operations
Surface facilities and uranium extraction at ISL operations are regulated by the NRC or its Agreement
States; liquid and solid wastes produced are considered to be byproduct materials under the AEA. In
general, ISL operations generate small amounts of surface solid waste comprised of: (1) soil and
weathered bedrock material disturbed during surface preparation of the site, (2) waste from drilling of
injection and production wells, and (3) solids precipitated during the storage and processing of fluids in
holding ponds. The site surface preparation may include site grading for placement of temporary
structures, construction of access roads to well sites, laying of pipelines, and constmction of well pads.
Disturbance of the site may make these surface materials more likely to be windblown, but the disturbed
material would likely have background radionuclide concentrations typical of levels present at the site
before the mine's development. Drilling wastes include drilling muds, water, chemicals, and drill cuttings
from the underground rock formations (Figure 3.2). These wastes are typically deposited in pits on site,
which are subsequently buried during reclamation. Some slight radioactivity may occur in accumulated
solids in the pit bottoms.
Leachate solutions circulating in the formation mobilize uranium and in some instances a part of their
associated uranium decay products. Alkaline leach and ammonium bicarbonate solutions at sites remove
about 15 percent of the radium in the uranium ore body (Brown 1978). More current solution mining
techniques make use of dissolved oxygen and carbon dioxide. The amount of radium and other uranium
decay products removed by these more recently used solutions is not known.
3-9

-------
Liquid wastes from ISL operations are generated from three sources: (1) well field development, (2)
processing plant operations, and (3) aquifer restoration activities. Limited data are available on the
volume of this material. Options for the disposal of liquid wastes include solar evaporation ponds or deep-
well injection. Land application is not an approved method of radioactive liquid waste disposal.
EPA studied sites for this report using data in NRC and State of Texas files, as well as site visits in Texas
and Wyoming. For information purposes only, radionuclide data for ponds and injection wells collected
for this report can be found in Appendix V. Descriptions of ISL fields studied are included in Appendix
III.
Based on information collected, operators typically used numerous ponds for holding or disposing of
produced water and brines (Figure 3.3). They ranged from 50 acre-feet (Irigaray) to 558 acre-feet
(Highlands) per pond. In many cases, this water was eventually disposed of in deep-injection wells or was
allowed to evaporate. In the case of evaporation, Crow Butte Resources estimated its operation would
have generated 1,315 cubic yards (902 cubic meters), or eight acre-feet, of solid waste by mid-2000. NRC
permitted that and other operations, such as Cogema's Christensen Ranch and Irigaray mines, to dispose
of these wastes off site in byproduct tailings impoundments at other uranium-producing facilities.
Available data are insufficient to estimate the total amount of solid and liquid wastes generated by
existing and previous ISL operations.
Figure 3.2. ISL Operation Drilling Site
In this photo taken at a Wyoming ISL field, a truck-mounted rig is drilling a well. Top soils
moved to level the site for drilling can be seen in front of the tank truck on the right of the picture.
The soils must be used to restore the site after production is completed in accordance
with Wyoming Department of Environmental Quality requirements.
(Photograph by Mark Schnknecht, U.S. EPA)
3-10

-------
Figure 3.3. ISL Evaporation Pond
This Wyoming ISL operation has a modern liner to prevent contaminated
waters from leaching into the ground.
(Photogmph by Mark Schukneeht, U.S. EPA)
Physical Characteristics of Uranium Mine Wastes
The characteristics of overburden and barren or waste rock from conventional mines depend on the
geology of the zone where the ore was originally mined, and how the waste was subsequently treated.
Knowing the rock types present is important for constructing risk model inputs, evaluating environmental
impacts, and determining the most effective means of site reclamation. Common rock types found in
mines from New Mexico, Texas and Wyoming include a wide variety of sedimentary, metamorphic, and
igneous rock types (Table 3.6).
3-11

-------
Table 3.6. Examples of Waste Rock Types Found
at Uranium Mines in Selected States
The characteristics of overburden and barren or waste rock from conventional
mines depend on the geology of the zone where the ore was originally mined,
and how the waste was subsequently treated.
State
Sedimentary Rock Types
Metamorphic and Igneous
Rock Types
New Mexico
Sandstone, siltstone, shale, claystone, limestone,
unconsolidated silt, clay, gravel

Wyoming
Sandstone, siltstone, shale, claystone, limestone,
coal, unconsolidated silt, clay, gravel

Texas
Sandstone, siltstone, shale, claystone, limestone,
coal, unconsolidated silt, clay, gravel, volcanic
tuffaceous silts, volcanic ash

Oregon
(Lucky Lass/White King case study)

Rhyolite, tuff breccia, basalt
Washington
(Midnite Mine case study)

Mica phyllite, mica schist,
hornfels, marble, quartzite,
calcareous silicates, quartz
monzonite, granitic intrusives
Sources: U.S. EPA 1983a,b,c; 2001a.
Overburden from surface mines can include huge boulders that may have been broken down with
explosives and heavy machinery into particles down to a micrometer (|om, one-millionth of a meter) in
diameter (U.S. EPA 1983b). Table 3.7 presents the size distributions provided in a study of rock
overburden from an unidentified Pennsylvania mine.
Table 3.7. Overburden Particle Size Distributions, Pennsylvania Mine
Overburden from surface mines can range in size from a micrometer
to a meter or more in diameter.
Particle Size (urn)
Weight (%)
> 2,000
75
50-2,000
13
2-50
8
<2
4
Source: Rogowski 1978.
Overburden test pits at the Midnite Mine were excavated to depths ranging from 10 to 14 feet (three to
four meters) (URS 2002). In general, the test pits encountered coarse-grained materials consisting of sand,
gravel, cobbles, and boulders, while one test pit encountered clay from a depth of eight feet (two meters)
to the bottom of the pit (14 feet or four meters). The wide range of grain sizes of the materials
3-12

-------
encountered in the test pits and the presence of open void space indicate the highly heterogeneous nature
of the waste rock.
Size gradation tests of individual test pit samples indicated gravel (5-65 percent), sand (21-43 percent)
and silt and clay (or fines) (11-29 percent), showing great heterogeneity across the mine site. The
moisture content of the waste rock material generally ranges from two to nine percent, with two samples
as high as 23 percent. The specific gravity ranges from 2.75 to 2.84.
The White King/Lucky Lass Superfund site in Oregon (see Appendix III) has a large protore stockpile
and a large overburden pile (Table 3.8). For all mines sampled, particle sizes for protore materials are the
same as found with overburden and ore piles (EPA 1983b). Because unreclaimed rock piles are not
stabilized, they can serve as sources of pollution, primarily through wind and water erosion. Fine
particulates in general are susceptible both to aerial suspension and to transport in water as both
suspended and dissolved solids in precipitation runoff.
Table 3.8. White King/Lucky Lass Mine Protore and Overburden Characteristics
Waste pile sizes are shown in acres (hectares) and cubic yards (cubic meters).
Stockpile Type
Protore
Overburden
Area
17 acres (7 hectares)
24 acres (10 hectares)
Volume
542,000 yards3 (408,000 m3)
408,000 yards3 (307,000 m3)
Thickness range
8-27 ft (2-8 m)
7-33 ft (2-10 m)
Type of material
Gravel, silt, clay layers, gravel at
surface
Gravel at surface, sand and clay below,
though more clay-like
Source: U.S. EPA 2001a.
Radionuclide leaching primarily from mine waste piles adjacent to open-pit mines—but also possibly
derived by leaching from mine pit walls or by groundwater infiltration from underlying uranium
deposits—can result in significant concentrations of radionuclides in water-filled pit lakes. Appendix V
includes data on radionuclide concentrations found in numerous pit lakes and streams associated with
open-pit mines.
The Yazzie-312 Mine (see Appendix III) is an example of a small surface mine that had a number of both
protore and overburden waste piles located adjacent to the mine pit, which had filled with water. Runoff
from precipitation over a 40-year period carried fine-grained materials back into the pit. The original pit
was 40 feet (12 meters) deep, but infilling by runoff had left the pit only five feet (1.5 meters) deep as of
2001 when the mine underwent reclamation. Suspended sediment of clays and silts pervaded the pit
water, leaving it a milky white color. Analyses (Panacea 2002) of 10 samples of pit lake water showed the
following average contaminant concentrations: Total Uranium 173 pCi/L, Total Radium 2 pCi/L, and
Total Thorium < 1 pCi/L. More information on overburden and protore wastes at this site can be found in
the section in this chapter on Heavy Metals in Mine Wastes.
Figure 3.4a below shows a picture of one of the several overburden piles, while Figure 3.4b shows a
picture of the pit lake.
3-13

-------
Figure 3.4a. Overburden Pile at Yazzie-312 Open-pit Mine, Navajo Reservation, Arizona
Fine-grained overburden materials are found adjacent to the Yazzie-312 Mine in Cameron, Arizona.
(Photograph by Loren Setlow, U.S. EPA)
Figure 3.4b. Pit Lake at Yazzie-312 Open-pit Mine, Navajo Reservation, Arizona
Football field size water filled open-pit mine. The original pit was 40 feet (12 meters) deep, but infilling
by runoffhad left the pit only five feet (1.5 meters) deep as of2001 when the mine underwent reclamation.
(Photograph by Loren Setlow, US- EPA)
Wastes from underground mines are much smaller than overburden piles generated by surface mines, and
tend to be located near the mine entrances. When the land near the mine is relatively flat, the waste piles
are dome shaped. In contrast, if the mine is located along a canyon rim or other steep elevation, the wastes
form thin sheets extending beyond the mine entrance. The wastes consist of protore and barren or waste
rock, and the protore may generally be found on top of the mine waste rock. The Canyonlands waste piles
3-14

-------
described previously in Table 3.5 and Figure 3.1, and the description of the Orphan Mine (in Appendix
III) provide examples of mine wastes from underground mines.
Potential for Water Contamination
Uranium mines are located throughout the West. Surface and underground mines have varying potential
to contaminate aquifers and surface water depending on the meteorological, hydrologic, and geologic site
characteristics. As mentioned previously, EPA has published comprehensive reports on uranium
geochemistry with detailed discussions on fate and transport of uranium in the environment (U.S. EPA
1999b and 1999c). Potential impacts from new mines can be mitigated by modern control technologies.
Older abandoned mines may present complex contamination problems.
Types of mines in relation to hydrologic factors for groundwater impacts include:
1.	Surface open-pit mines in the unsaturated zone, above a confined aquifer, sometimes
with a water-filled pit. A large number of mines in the Colorado Plateau, such as the Yazzie-
312 Mine, fall into this category. The Colorado Plateau physiographic province is
characterized by low precipitation and high evapotranspiration (Figure 3.5). Much of the
Colorado Plateau receives less than 15 inches of precipitation a year. The area's low
precipitation and high evapotranspiration reduce the potential for infiltration, although low-
frequency, high-intensity rain events may contribute mass movement. Surface mines in New
Mexico and Arizona are often isolated from water sources due to lack of dependable surface
water or the large vertical distance separating the mines from the confined aquifers below.
The U.S. Geological Survey Groundwater Atlas of the United States (Robson and Banta
1995) indicates that the Colorado Plateau has very few surficial aquifers, so water sources are
typically derived from deeper groundwater (Figure 3.6). The more numerous surficial
aquifers away from the Colorado Plateau pose a greater potential for shallow groundwater
contamination outside of the area.
2.	Surface open-pit mines in or just above the saturated zone or close to an aquifer, often
with a water-filled pit or pits. The White King and Lucky Lass mines and the Midnite Mine
are examples of this category.
3.	Underground mines in the saturated zone. Some mines have been developed so deep that
radionuclides could move through the aquifer, even in the Colorado Plateau. The Orphan
Mine which is located below the rim of the Grand Canyon is a good example of this situation.
4.	Underground mines in an unsaturated zone that may be close to an aquifer. Mines in the
Four Corners area, such as the Lathrop Canyon, are typical of this category. Mines along
canyon walls would also be part of this category.
It should be noted that uranium concentrations in undisturbed, near surface groundwater can be quite
high, as demonstrated by Sheridan et al. (1962). High evaporation rates as opposed to very low
precipitation rates in many parts of the western U.S. may reduce the potential for communication between
contaminated surface water and deeper groundwater.
3-15

-------
Figure 3.5. Average Annual Precipitation in the Western United States
Much of the Colorado Plateau receives less than 15 inches (38 cm) of precipitation a year.
The area's low precipitation and high evapotranspiration reduce the potential for infiltration,
although low-frequency, high-intensity rain events may contribute mass movement.
A\/pranp Annual Precipitation
Legend
i"_1 Colorado Ptotpju Boundary^
PredpJtatfon. Inches/Yeas1
CUD-s
I—15-10
I—1 ID- 15
¦115-20
H2Q-30	o
H30-JD	|	
¦ID • 50
ISD - IDD	Kin meters
11 do - isj m ap Derived From National Atlas
USD-200
Source: Spatial Climate Analysis Service et al. 2000.
3-16

-------
Figure 3.6. Surficial Aquifers of the Colorado Plateau
BJ(PI.AriATIC>K
E«lcrl nf piacjrtl	m' ceGfcTi «fc?#4£»
Swift PMlc ftw Vikj «i
EH	5i"ti VM^r ii r*
llpUftd pUiru..iii«
EZT3 L!iiC: end Huge mm
E23 fco CurtJc E&ahi woa
Dm'H Mm
¦ — — — — ^¦pp	rXi ULOMTTIIW
Source: Robson and Bcmta (1995)
Much of the discussion which follows is from U.S. EPA (1995); however, extensive information on this
topic can be found in U.S. EPA (1983b).
3-17

-------
Surface water which can enter a mine is generally controlled using engineering techniques. During the life
of the mine, mine water from groundwater inflow or seepage is pumped out as necessary to keep the mine
dry and allow access to the ore body for extraction. This water may be pumped from sumps within the
mine pit or underground workings, or may be withdrawn from the vicinity of mining activity through
interceptor wells. Interceptor wells are used to remove groundwater, creating a cone of depression in the
water table surrounding the mine; the result is dewatering of the mine. Mine water may be treated and
discharged (subject to 40 CFR 440 Subpart C) (see Appendix VI for more information).
The quantity and chemical composition of mine water generated at mines vary by site and are dependent
on the geochemistry of the ore body and surrounding area. Prior to being discharged, mine water from
uranium mines is usually treated with a flocculent and barium chloride to reduce suspended solids
concentrations and to co-precipitate radium. The chemical quality of mine waters may differ from the
receiving surface waters. In arid climates, like New Mexico, the discharge of mine water to a receiving
stream can completely change the hydrologic conditions of the receiving body. Typically, mine water is
discharged to ephemeral streams in arid climates. The mine waters have, in some instances, transformed
ephemeral streams to perennial streams. These newly created perennial streams often lose flow to
subsurface alluvial material which recharges shallow alluvial aquifers. Studies have documented that
infiltration of uranium mine dewatering effluents have been accompanied by a gradual change in the
overall chemistry of the groundwater, and the groundwater then bears a greater resemblance to the mine
dewatering effluent (U.S. EPA 1995a).
For example, in the Grants Mineral Belt of New Mexico, authorized discharges of mine dewatering
effluents have been documented to contain elevated concentrations of gross alpha and beta radiation;
radionuclides radium-226 and lead-210; natural uranium; molybdenum; selenium; and dissolved solids,
with sulfate in particular (Eadie and Kaufmann 1977). On occasion, arsenic, barium and vanadium are
detected (U.S. EPA 1995a).
In cases of abandoned conventional uranium mines, radionuclides, metals, and salts either in solution or
as solids may be eroded and carried away from a mine or waste pile and carried by wind and water over
time. Waters affected by uranium mining may be on, adjacent to, or at some distance from a mine or
mines. Pit lakes, such as the Yazzie-312 (see Appendix III), may be immediately affected by infill from
adjacent waste piles and may take on the pollutant burdens of those piles. However, measurements taken
by EPA of the Little Colorado River a mile or so downstream from the Yazzie-312 Mine did not
demonstrate a correlation with metals and radionuclides that were present in the pit lake, despite erosion
channels downslope from the mine leading toward the river.
Similarly, in other case studies (see Appendix III) waterborne erosion from Utah's Canyonlands mines
had carried radionuclides and metals only a small distance from the mine mouths. However, surface and
subsurface drainage from Arizona's Orphan Mine appeared to be polluting nearby springs. Radionuclides
and metals in ground and surface waters from the Midnite Mine in Washington state have spread to areas
outside the mined area in surface water and sediments, groundwater, and road dust; most runoff from the
mined area flows to three drainages which meet south of the mine and flow into Blue Creek. Runoff and
groundwater pollution were also concentrated in groundwater from mines in the vicinity of Blue Water,
New Mexico, resulting in a Superfund action to shut a well in.
Geographic and geologic differences play a large role in the likelihood of pollutants naturally migrating
from a mine site. The case studies' data, cited in Appendix III, provide information on the metal and
radionuclide data from ground and surface waters. Uranium and thorium, and radium to a lesser extent,
3-18

-------
can be mobilized by either acidic or alkaline solutions (see section below on Potential for Soil
Contamination of Soil). Pyrite and other sulfur-bearing minerals are key determinants as to whether acid
mine drainage occurs, while carbonate minerals, organic carbon and carbon dioxide may also influence
migration of radionuclides in a neutral or alkaline environment. Geography and climate determine how
much water and wind may be present to erode the mine waste and move it away from its place of origin.
Most of the mines located in the sedimentary sandstone deposits of the southwestern United States are not
in pyritic formations, and the resulting runoff waters or pit lakes are generally neutral to alkaline in
character (pH of seven or higher). Low precipitation rates and the resultant lack of water may further
reduce the potential for generation of acid drainage from waste rock, for example, in both the Colorado
Plateau and the Shirley Basin of Wyoming.
Runoff waters at Horn Creek below the Orphan Mine had a pH generally between six and eight; Blue
Water measurements were generally alkaline in the 8.0 range in wells and river water in the vicinity;
Yazzie-312's pit water was measured by Longsworth (1994) at pH 8.7. However, those measurements
contrast with the numbers found at mine locations in the Pacific Northwest—areas with higher-than-
average rainfall amounts and metamorphic and igneous rocks, including sulfur-bearing minerals that
could transform runoff into acidic waters (pH < 7). Acid mine drainage had occurred at Midnite where,
for example, in measurements from 1990 to 1992 the pH of water in wells and the pits ranged from 4.0 to
7.2 (Williams and Riley 1993). Acid mine drainage had also occurred at the White King pond, where pH
has historically ranged from 3.0 to 4.5 due to acid generation during oxidation of sulfide minerals
exposed in the pond bottom, walls, and underground mine workings (U.S. EPA 2001a).
At the end of a mine's active life, pumping typically is stopped and the pit or underground workings are
allowed to fill with water. The mine water may be contaminated with radioactive constituents, metals, and
suspended and dissolved solids, and reclamation or groundwater protection methods may vary by the
responsible land management agency.
It should be noted that groundwater impacted or potentially impacted by mining activities is not
necessarily suited for domestic use prior to mining. For example, aquifers containing uranium ores in both
Wyoming and New Mexico have been documented as having elevated levels of uranium and other
radionuclides prior to the initiation of mining activities (WDEQ 1991; Eadie and Kaufmann 1977).
Uranium is mobile in water, and sediments as discussed in the section below, in both acidic and alkaline
conditions (U.S. EPA 1999b and 1999c). Even though the majority of U.S. conventional mines are
located in areas of low annual rainfall, the periods of high precipitation (usually Spring and Summer
months) may be sufficient to result in eventual migration of radionuclides into groundwater or surface
water bodies, soils, and make them available for uptake in vegetation. Radium is considered moderately
soluble in natural waters and its fate is controlled mostly by the presence of sulfate and organic materials
(U.S. EPA 2004b). The section below on potential for contamination of soil and vegetation is principally
drawn from those three reports.
Potential for Soil Contamination
In evaluating the mobility of radionuclides in the environment, an important measure is the element-
specific soil/water partition coefficient, which is represented as Kd In general, the adsorption of uranium
by soils and single-mineral phases is low at pH values less than three, increases rapidly with increasing
3-19

-------
pH from three to five, reaches a maximum in adsorption in the pH range from five to eight, then decreases
with increasing pH at pH values greater than eight. This trend is related to the pH-dependent surface
charge properties of the soil minerals and complex aqueous behavior of dissolved uranium (U(VI)). It is
especially true near neutral pH, or above (alkaline) conditions where dissolved uranium forms strong
molecular complexes with dissolved carbonate. Additionally, soils containing larger percentages of iron
oxide minerals and mineral coatings, and/or clay minerals will exhibit higher sorption characteristics than
soils dominated by quartz and feldspar minerals. In fact, maximum limits for Ka have been calculated for
iron-oxides and clay minerals (Waite et al. 1992).
Radium is an alkaline earth element, and is found naturally only in the +2 oxidation state. In flowing and
soil water it can be found dissolved in a pH range of from three to ten. However, in the presence of sulfate
bearing waters, precipitation and dissolution of calcium, strontium and barium sulfates may control the
concentration of dissolved radium in the soil environment. Only limited Kd are available for radium in
soils and sediments. However, it is known to be most strongly absorbed by ion exchange on clay
minerals, organic materials, and mineral oxides especially in near neutral and alkaline pH conditions.
Differences in partial pressure of carbon dioxide have a major effect on uranium adsorption at neutral pH
conditions. In one study (Ibid.) the percent of uranium (U(VI)) adsorbed on ferrihydrite (an iron oxide
mineral) decreases from approximately 97 to 38 percent when carbon dioxide is increased from ambient
levels (0.03 percent) to elevated (one percent) partial pressures. Based on this uranium adsorption
behavior, the adsorption of uranium decreases rapidly at pH values greater than eight for waters in contact
with carbon dioxide or carbonate minerals. This means that in such situations, uranium becomes very
mobile and subject to transport in soil and water away from waste sites, potentially for considerable
distances (e.g., Kaplan et al. 1994). Extensive literature exists for the fate and transport of radium and the
reader is consequently referred to Benes (1990), Frissel and Koster (1990), Dickson (1990), Onishi et al.
(1981), Ames and Rai (1978), as well as detailed review in IAEA (1990) and Cothern and Rebers 1990).
Much of that is summarized in U.S. EPA (2004b).
Models of contaminant transport typically evaluate the subsurface environment as being divided between
a mobile aqueous phase and immobile solid phase (soil). However, under some subsurface conditions,
components of the solid phase exist as colloids4 that may be transported with flowing water in the pore
spaces of underground rock and sediment. This may enhance the amount and rate of contaminant
transport. Due to field sampling and collection difficulties to enhance available data, contaminant models
have mostly ignored this phenomenon. However, subsurface mobile colloids originate from dispersion of
surface or subsurface soils, dissolution of natural rock binding cements, and homogeneous precipitation
of groundwater constituents (McCarthy and Degueldre 1993). Colloids can be dispersed and become
mobile in aquifers due to groundwater chemistry or microbiological changes.
Hazardous Characteristics of Uranium Mine Waste
The primary hazardous characteristics of uranium mine waste are elevated radioactivity as radon
emanations and elevated gamma radiation, heavy metals, and contaminated water.
4 Colloids are any fine-grained material, sometimes limited to the particle-size range of <0.00024 mm (i.e., smaller
than clay size), that can be easily suspended in fluid (Bates and Jackson 1979).
3-20

-------
Elevated Radioactivity
Conventional Mines
It should be expected that materials associated with the mining of uranium would have radioactivity
above that which would be considered background levels in most parts of the country, not only because
uranium is radioactive, but also because the many decay products that accompany it are radioactive as
well. The uranium-238 decay chain consists of 13 radioactive elements and the stable end point lead-206
(see Appendix II). Overtime, uranium and its decay products achieve a state of equilibrium, meaning that
the quantities of each radionuclide are proportional to their half-lives (not considering environmental and
geotechnical factors), and their activities are equal. In other words, radioactive equilibrium for a decay
chain occurs when the each radionuclide decays at the same rate it is produced. At equilibrium, all
radionuclides decay at the same rate (i.e., the same number of atoms disintegrate per unit time for each
member of the chain). Understanding the equilibrium for a given decay series helps scientists estimate the
amount of radiation that will be present at various stages of the decay.
While high uranium concentrations may be—and often are—measured in wastes, uranium mining
TENORM is generally characterized by its more hazardous decay products. In particular, the
concentration of radium-226 is a key metric for purposes of classifying waste materials. Radium is the
radionuclide of interest at uranium TENORM sites for two reasons: its decay products give off strong
gamma radiation that is easy to measure, and it has the most significance for human health risks due to
radon generation. Radium is also often used to characterize TENORM, as it can be in serious
disequilibrium with uranium in TENORM as a result of processing. Reports of TENORM radionuclide
concentrations obtained from wastes at different mine sites can vary greatly, depending on the geographic
location, the type of waste sampled, how deep the sampled material was in the waste pile, how long the
material had been exposed on the surface, impacts of weather, and many other variables. Following are
the results of some sampling efforts which provide a variety of measurements, sometimes conflicting, but
nevertheless yielding a range of values for radionuclides found at uranium mine sites.
In one study, radionuclide concentrations in overburden and waste rock were reported from 58 samples
collected from 17 uranium mines across the U.S. (U.S. EPA 1985). Data indicate that 69 percent of the
samples were elevated in radium-226 concentrations (defined as concentrations greater than or equal to 5
pCi/g (0.185 Bq/g)), and over 50 percent had concentrations above 20 pCi/g (0.74 Bq/g). In another
study, the White King mine had radium concentrations of 53 pCi/g (1.96 Bq/g) in the near-surface
overburden, while the Lucky Lass mine, mined just a short distance away in a slightly different geologic
source rock, had only 2 pCi/g (0.07 Bq/g) in the near-surface overburden (Weston 1997).
The results of another EPA study (SC&A 1989) involving overburden material sampling and analyses
indicate average radium-226 concentrations of 25 pCi/g (0.94 Bq/g), ranging from 3 pCi/g (0.113 Bq/g)
up to a few hundred pCi/g (> 7.4 Bq/g); the higher concentrations were found in weakly mineralized rock
near the ore body. ISL operations for mines other than uranium, can leave behind significant amounts of
radionuclides in wastes, though in many cases the aquifer may have been exempted from being
considered as a drinking water source, or the aquifer may have been contaminated with radionuclides or
metals prior to ISL activities. EPA's 1999 report on TENORM from copper mines in Arizona, for
example, provides information on this problem in the copper mining industry (U.S. EPA 1999a).
Additional data, including several more recent studies from mine reclamation assessment studies, indicate
that material identified as "waste" or "overburden" varies widely in radium-226 activity, but that for most
waste piles dominated by overburden material, measurements higher than 20 pCi/g (0.74 Bq/g) are
3-21

-------
unusual (see Appendix V). In fact the State of Wyoming uses 20 pCi/g (0.74 Bq/g) as a key value for
mine reclamation because materials with higher measurements are considered unsuitable for placement
below the water table, or close to the graded surface according to state reclamation practice (Otton 1998).
Protore, on the other hand, was considerably higher in radium-226 activity, with most material in the
range of 30-600 pCi/g (1.11-22.2 Bq/g).
Once protore or overburden has been removed from the ground, equilibrium of the radioactive decay chain
may no longer be a safe assumption. Data on the parent element and decay product activities of uranium
mine overburden have been gathered fairly recently, usually as part of assessment of mine wastes prior to
reclamation. Disequilibrium between uranium-238 and its decay products seems common in those waste
materials studied in some detail. One observer has noted a tendency for the lower part of waste piles at
small mines in southeastern Utah to have higher uranium-238 activities relative to radium-226 activities,
suggesting leaching of uranium from the upper part of the piles (Burghardt 1998). In leach studies of mine
waste from open-pits in two districts in Arizona and Utah, Longsworth (1994) suggests that uranium is far
more soluble in mine waste than radium. In samples of waste material in piles in the Pumpkin Buttes
district (AVI 1990), the uranium-radium activity ratio varies from 0.10 to 7.15 (equilibrium would mean
the activity ratio equals 1). It is not known whether these disequilibrium conditions are due entirely to
weathering of the waste piles, or if disequilibrium conditions also occurred in waste rock and protore
surrounding the ore body prior to mining. Other members of the uranium-238 decay chains that are also
potentially hazardous may be present in significant quantities due to disequilibrium conditions; lead-214
and bismuth-214 are important surrogates for radium-226 within the radium-226 subchain. Further careful
study of equilibrium conditions is warranted.
ISL and Heap Leach Operations
Licensed ISL and heap leach operations, reclamation, and waste disposal are carried out under the
regulatory oversight of NRC or its Agreement States. The radionuclide information on these types of
uranium extraction facilities is provided for background only, as the wastes are considered to be byproduct
materials in accordance with the AEA.
Information on radionuclides present in ISL operation wastewater ponds is very limited. These liquid
wastes have some residual uranium and radium-226 activities that range from background levels to
concentrations as high as 3,000 pCi/L (111 Bq/L) (Brown 1978). Such liquid wastes are treated with
barium chloride to precipitate out radium. The solid wastes are typically comprised of carbonate and
sulfate mineral solids that contain several hundred ppm uranium and 300-3,000 pCi/g radium-226
(11.1-111 Bq/g) (Brown 1978). Solid wastes are generally packaged and shipped off site for disposal at
licensed facilities.
Not every ISL operation generates large quantities of these wastes, as the quantities are determined by the
ore body's geochemical characteristics and its interactions with the leachate solutions. Data collected by
EPA in 2000, from reports on files at the NRC and the state agencies in Texas and Wyoming, showed
radium-226 in the wastewater can range from background levels to 2,119 pCi/L (78.4 Bq/L), whereas
total uranium may be as high as 1,100 mg/L (see Appendix V). NRC and state licensing and permits at
uranium solution mining operations sites require cleanup of all surface wastes. Aquifer restoration may or
may not be required by the regulating agencies depending upon its geologic and hydrologic conditions.
Discussion of regulation of ISL facilities can be found in Appendix VI.
Some low-grade ore, waste rock, and tailings were used in dump or heap leaching, a process that the
mining industry considered a form of beneficiation and one that involved spraying ore with acid to leach
3-22

-------
out metals (see Chapter 2). When leaching no longer produced economically attractive quantities of
valuable metals, and the sites were no longer in use, the spent ore was often left in place or nearby
without further treatment (U.S. EPA 1985). Heap leaching generates wastes that are similar to mill
tailings in radioactivity. While this mining technique was less often used before the mid-1970s, some
abandoned heap leach piles have been reported. After the mid-1970s, mining heap leach piles became
subject to state and federal cleanup requirements.
Radon Emanation
Radon (Rn-222) is a key health concern associated with uranium mines and sites where TENORM is
found. Radon is part of the uranium decay series, and has the property of being a gas, which means its
mobility rate is vastly different from that of radioactive metals. Radon is a decay product of radium-226.
When radium is high, radon production is high. The occurrence of radon in underground uranium mines
and the occurrence of cancers in Czechoslovakian miners working in such mines formed the basis of one
of a number of studies which have established an important epidemiological relationship used for
modeling cancer risk from radiation exposures. EPA limits emissions of radon from operating
underground uranium mines such that exposures to a member of the public is limited to no more than 10
millirems annually, and the operator must provide a report of their compliance to that requirement to EPA
yearly.
Radon measurements in some abandoned mines where mechanical ventilation has ceased are quite high,
and pose risks for prolonged human exposure by members of the public visiting for recreation,
exploration of old workings for geologic purposes, or reclamation workers at abandoned sites. As an
example, radon readings by alpha track canisters installed at underground mine portals of the Ross Adams
uranium mine in Alaska measured from 212 pCi/L to 540 pCi/L (7.84 to 19.98 Bq/L) (U.S. BLM 1998).
For comparison purposes only (since this in not an operating mine), annual underground uranium mine
occupational levels of alpha radiation5 are limited to no more than four working level months (WLM) at
full equilibrium (one WL ~ 100 pCi/1). A worker's annual exposure to the radon levels reported from the
Ross Adams mine would be limited to between 32 and 83 hours.
Radon emanation coefficients (the fraction of radon atoms present in a material that emanate into rock or
sediment pore space) for barren (low-activity) sandstone overburden range from three to twelve percent
and average about five percent (Barretto 1975). Emanation coefficients for sandstone and other uranium
ores are extremely variable. Coefficients vary with: (1) uranium mineralogy; (2) radium mineralogy; (3)
host rock lithology; (4) grain size of uranium/radium minerals; (5) comminution, or fineness, of the ore;
(6) estimated porosity and permeability of the ore; (7) moisture content; and (8) ore grade.
An exhaustive study of emanation for 950 ore samples from all the major sandstone uranium mine
districts, deposits at Lakeview, Oregon, and deposits in the Front Range of Colorado (Austin 1978)
revealed coefficients ranging from < one percent to 91 percent. The median value for all 950 samples is
about 22 percent; however, extreme differences in median values occur regionally. Ores in the Lisbon
Valley district of Utah have median values of less than 10 percent, whereas ores in some districts in
Wyoming have median values exceeding 50 percent. These data suggest that low-activity sandstone waste
material not only has little radon forming in it, but tends to release very little of that radon. However,
overburden, waste rock and protore piles with elevated activity not only have much more radon forming,
5 Regulated by the Mine Health Safety Administration of the Department of Labor--30 CFR, Part 57, Subpart D.
3-23

-------
but in many districts they release a great deal of that radon to pore spaces, and the radon is free to
migrate.
Radon flux rates from overburden are difficult to characterize because of the rock's diverse physical
forms and matrices, and diverse emplacement and disposal methods. Field measurements indicate that
average radon flux rates vary from about 2-60 pCi/m2s (0.07-2.22 Bq/m2s) for overburden materials to as
high as a few hundred pCi/m2s (> 7.4 Bq/m2s) for low-grade ore materials (U.S. EPA 1989b, SC&A
1989). The broad range of radon flux rates is due in part to varying radium concentrations (the parent
radionuclide) found in low-grade ores that are at times disposed of with overburden. The average flux
rate, based on data from 25 mines, was estimated to be 11.1 pCi/m2s (0.41 Bq/m2s) for overburden
materials. A radon flux rate of 92.4 pCi/m2s (3.42 Bq/m2s) was reported for a spoil area located at the Day
Loma mine in the Gas Hills District of Wyoming (SMI 1996); however, this material appears to have
been a heap leach pile. For comparison, background radon flux rates from soils are known to vary from
about 0.6 to 5.0 pCi/m2s (0.02 to 0.19 Bq/m2s) (SC&A 1989; U.S. NRC 1980). However, Kennecott
Uranium Company (2004) found an undisturbed area adjacent to a uranium extraction operation which
had background radon flux rates in excess of 100 pCi/m2-sec; in addition, the company believes other
undisturbed uraniferous outcrops in the Gas Hills of Wyoming should also have elevated radon flux rates.
In its 1983 report to Congress, EPA cited measurement results for various waste materials taken at six
mines (Table 3.9). The data indicated an average radon flux estimate of 9.4 ±3.9 pCi/m2s (0.35 ± 0.14
Bq/m2s). The report assumed that an average radon flux rate of 8.7 pCi/m2s (0.32 Bq/m2s) existed for
overburden materials. In light of the 25 mine study results from the 1989 review, a radon flux rate of 10
pCi/m2s (0.37 Bq/m2s) is assumed to be representative, while recognizing that in some instances radon
flux rates could be higher by a factor of six.
Table 3.9. Radon Flux from Selected Uranium Mine Wastes
Flux rates of radon from six selected uranium mine wastes vary by a factor of up to four.
Type of Mine
Waste/Material
Average Radon Flux
pCi/m2s (Bq/m2s)
Underground
San Mateo
Waste pile
18(0.67)
Barbara J# 1
Waste pile
7.9 (0.29)
Surface
Poison Canyon-1
Protore
Overburden pile
7.0 (0.26)
6.7 (0.22)
Poison Canyon-2
Protore
Overburden pile
5.3 (0.2)
9.8(0.36)
Poison Canyon-3
Protore
Protore
11 (0.4)
24 (0.89)
Morton Ranch
Overburden
9.7(0.36)
Source: U.S. EPA 1983b. (Table modified to substitute the term Protore for "Subore ")
Given that the current overburden stockpiles represent decades of mining activities, the radon flux
reported in various field studies may in fact reflect the aggregate properties of materials accumulated at
one location and not that of the surface material. Because most overburden piles also contain some
amounts of weakly mineralized waste rock, the results are likely to be influenced by the presence of
materials containing higher levels of uranium. However, large volumes of this weakly mineralized waste
are not expected. Since the amount of overburden far exceeds the volume of this waste, it is assumed that
3-24

-------
radon emanation rates from such material would not significantly increase the overall average emanation
rate.
Elevated Gamma Radiation Exposure Rates
Elevated gamma radiation is always found at uranium mine sites. The primary contributors to gamma
exposure are the decay products of radium; the higher the radium present, the higher the ultimate gamma
exposure rate. Radium content is also roughly proportional to uranium content in raw mine materials.
Exposure rates associated with ambient background levels ranged from 10 to 85 (j,R/hr, averaging about
20 (j,R/hr.
Gamma radiation exposure measurements were taken on overburden piles in support of the
characterization of 25 uranium mine sites located in five states (U.S. EPA 1989b, SC&A 1989).
Additional information also comes from abandoned mine reclamation assessment studies from 1988 to
1996 and is included in Appendix V. In these various studies, exposure rates for overburden materials
range from 20 (j,R/hr to 300 (j,R/hr, with an average value estimated at 50 (j,R/hr, including background.
Protore ranges from 80 to 1,250 (j,R/hr, with an average value estimated at 350 (j,R/hr. These average
values may be significantly higher for waste materials at the surface of underground mine sites because of
the greater proportion of stockpiled protore to waste. Exposure levels of 200 to 1,000 |iR/hr would appear
to correspond to about 0.1 to 0.3 percent uranium ore grade.
Heavy Metals in Mine Wastes
A number of heavy (i.e., hazardous) metals may occur in association with uranium deposits and wastes
from uranium mining. Heavy metals on site, particularly arsenic, can be of concern, and can pose serious
risks if they migrate to groundwater. Available measurement data have tended to focus on individual sites
rather than survey many mines in an area. To that extent, some of the examples in Tables 3.9-3.11
provide a snapshot of what is known about the occurrence of metals in these wastes. The reader is
referred to U.S. EPA (1983b) which discusses in depth the movement of metals and radionuclides through
air, water, and groundwater, including leaching and other chemical reactions that move contaminants
from mine sites to the surrounding environment.
Table 3.10 from Wogman (1979) shows the analytical results of metals analysis from grab samples taken
at two mines, one in Wyoming and the other in New Mexico; except for selenium, vanadium and arsenic,
there did not appear to be a relationship between uranium mining materials and stable metals present in
the overburden. Table 3.11 provides the results of sampling and analyses of overburden and protore piles
at the Yazzie-312 Mine in Arizona (Panacea 2002); uranium and thorium concentrations as well as some
heavy metals in protore samples were much higher than those taken from overburden, and iron and
arsenic exceeded EPA Region IX preliminary soil remediation cleanup goals for industrial contaminated
sites. Table 3.12 shows the results of metals analyses for waste piles associated with several small
underground mines in a complex at Canyonlands National Park in Utah (Burghardt et al. 2000); there,
even though some of the metal levels may be high, contamination had not spread far from the waste piles.
3-25

-------
Table 3.10. Metals Sampling Data from Uranium Mines in New Mexico and Wyoming
This table reproduces information taken from mines in New Mexico and Wyoming on heavy metals present
in conventional mine wastes. Concentrations of metals are in p.g (micrograms) per gram of soil.
Samples
Concentration (jig/g)
As | Ba | Cu | Cr | Fe(a) | Hg | K(a) | Mn | Mo | Pb | Se | Sr | V | Zn | U
Wyoming
1. Top Soil Piles
3.2
700
13
46
1.3
<4
2.2
190
2.9
23
<1
89
60
37
6
2. Protore
<1.8
6800
9
<36
1.2
10
2.3
140
<2.2
22
2.1
128
<100
25
61
3. Ore
5.4
800
9
<27
1.1
<7
2.3
180
<2.9
16
28
94
200
25
370
New Mexico
4. Background Soil
4.1
450
12
<23
0.9
<4
1.8
200
5.5
12
<1
72
<60
22
<5
5. Background Soil
2.3
440
9
<20
0.8
<4
1.6
190
4.9
13
<1
50
<50
19
<5
6. Waste Pile
7.8
540
11
<28
0.8
<5
1.4
260
2.5
10
<1
99
<70
23
8
7. Waste Pile
14
280
21
<43
0.7
<8
0.5
750
<2.8
31
3.1
178
180
23
189
8. Pro tore + Waste
4.1
45
22
<51
0.3
<6
0.1
446
<1.8
25
<1.4
179
<55
13
57
9. Ore
6.0
64
27
<48
0.4
<6
0.2
673
<1.8
31
1.5
323
<55
14

Note: As = Arsenic, Ba = Barium, Cu = Copper, Cr = Chromium, Fe = Iron, Hg = Mercury, K = Potassium, Mn = Manganese, Mo = Molybdenum,
Pb = Lead, Se = Selenium, Sr = Strontium, V = Vanadium, Zn = Zinc, U = Uranium.
(a) Units are percent.
Source: Wogman (1979)
3-26

-------
Table 3.11. Radionuclides and Metals from Protore and Overburden, Yazzie-312 Mine, Arizona
This table provides a summary of data analyses from six protore and overburden waste piles at the Yazzie-312 Mine
prior to reclamation. Twelve samples were analyzed for uranium and thorium radionuclides content and other
radiological properties, as well as content of 23 metals. Selected data shown below are the range of average
and total uranium, and thorium, as well as seven selected heavy metals for one protore (WP-6), one overburden (WP-3) pile.
Additionally, values from all six waste piles are also provided, For reference, the EPA, Region IX preliminary
remediation goal (PRG) for contaminated industrial sites is also shown.
Sample Range
Total
Uranium
pCi/g
Total
Thorium
PCi/g
Arsenic
mg/Kg
Iron
mg/Kg
Lead
mg/Kg
Mercury
mg/Kg
Selenium
mg/Kg
Thallium
mg/Kg
Vanadium
mg/Kg
Waste Pile 6 -Protore
range of measurements
61.8—
121.9
36.8—
63.4
1.1—9.7
6000-
8100
21.3—
48.3
0.05—
0.19
0.13—
0.32
0.84—
18.4
12.3—20.5
(Avg. 3 samples)
(90.2)
(36.8)
(4.2)
(7207)
(39.1)
(0.13)
(0.25)
(6.73)
(17.7)
Waste Pile 3-Overburden
range of measurements
2.4—3.6
3.0—4.85
1.3—1.9
1020-
1430
11.8—
13.8
0.01—
0.01
0.27—
0.93
0.24—
0.28
15.2—33.5
(Avg. 3 samples)
(2.9)
(3.9)
(1.5)
(1356)
(12.6)
(0.01)
(0.50)
(0.26)
(21.4)
All Protore and
Overburden Samples
Range of measurements
2.4—
121.9
3.0—63.4
0.7—17
6000-
16200
7.9—
48.3
0.00—
0.19
0.13—
0.95
0.19—
18.4
8.2—33.5
(Avg. 12 samples)
(32.7)
(15.5)
(4.6)
(9867)
(21.8)
(0.05)
(0.47)
(1.91)
(17.0)
Metals Preliminary
Remediation Goal


1.6
10000
800
310
5100
67
1000
Source of Data: Panacea (2002), U.S. EPA (2004)
3-27

-------
Table 3.12. Metals in Canyonlands National Park Mine Waste Piles
Comparison of concentrations offour toxic metals from Canyonlands National Park spoil
piles from 12 underground mines. Multiple sampling locations were picked for each mine's
waste site. Samples were taken at multiple depths for each waste site and mixed together
(composited). The results provide the range of values for all samples, and for a few specific
mines. The statistical analysis of two standard deviations provides a measure of the
spread of values for the samples taken. All samples are reported in mg/Kg.
Analyte
Sample Range
All Samples
mg/Kg dry weight
Mine 4
Avg ± 2 SD
Mines 5,6, 7
Avg ± 2 SD
Mine 12
Avg ± 2 SD
Arsenic
19.1-155.1
50.7±5.7
124±13.3
12.1±1.9
Copper
79.3-7,910
429±79
3,500±982
322±25.7
Manganese
214.5-1,410
850±34
948±119
702±59.3
Selenium
0.3-2.4
0.7±0.03
2.7±0.8
0.3±0.02
Vanadium
4.8-35.6
8.1±0.8
9.8±1.3
29.6±2.5
Note: 2 SD = two standard deviations.
Source: Burghardt et al., 2000
Depending on local geology and climate, the presence and eventual leaching or remobilization of these
metals could lead to contamination of surrounding lands and water bodies. Analyses conducted on water
samples downstream from the Canyonlands mines found a correlation (similar concentration levels above
background levels) between manganese and selenium, though this dropped off rapidly within 150 feet (46
meters) of the mines.
However, in the Yazzie-312 Mine example from Table 3.11, water from rain events over 40 years carried
sediment in overburden and protore piles back into the pit (then a lake) from which they were originally
derived. Metal concentrations found in samples of spoil pile sediments and sediments collected from the
bottom of the pit lake were both elevated to the same general degree (order of magnitude concentration).
Uranium Mill Tailings
The following material summarizes only a small portion of information provided in U.S. EPA (1995;
1989b; 1986; 1983 a,b,c,d; and 1982), and NRC (1980) and the reader is referred to those reports for much
more detailed information on uranium milling and mill tailings. As mill tailings are considered byproduct
materials under the AEA and not TENORM, this section is provided only in order to provide a more
complete background and understanding of the uranium production industry.
Operational mills function independently of specific mines and generate materials that are, in most cases,
unique from those generated at the site of extraction. Under UMTRCA (Uranium Mill Tailings Radiation
Control Act; see Appendix VI for more information), source handling licenses place specific requirements
on the disposal of radioactive wastes; the design and construction of tailings impoundments address NRC
or its Agreement State requirements for permanent storage of these wastes. Radionuclide-containing
wastes generated by ISL operations are typically shipped to tailings impoundments at mill sites.
The principal waste generated by conventional beneficiation operations are tailings. ISL operations, and
to a more limited extent conventional mills, generate waste leaching solutions. Disposal of these wastes is
3-28

-------
dependent on the type of operation; beneficiation wastes generated by ISL are disposed of by different
methods, but most often shipment to NRC-licensed waste disposal facilities. Most beneficiation wastes
generated at conventional mills are disposed of in tailings impoundments.
Waste constituents of concern include radionuclides (radium, radon, thorium, and to a lesser extent lead),
arsenic, copper, selenium, vanadium, molybdenum, other heavy metals, and dissolved solids. Brines,
spent ion exchange resins, and chemicals used in beneficiation operations are also constituents of wastes
generated during beneficiation.
Most wastes generated by conventional mills are disposed of in tailings impoundments. Wastes are
primarily disposed of in the form of a slurry composed of tailings, gangue6 (including dissolved base
metals), spent beneficiation solutions, and process water bearing carbonate complexes (alkaline leaching)
and sulfuric acid (acid leaching), sodium, manganese, and iron. The characteristics of this waste vary
greatly, depending on the ore, the beneficiation procedure, and the source of the water (fresh or recycled).
The liquid component is usually decanted and recirculated to the crushing/grinding or leaching circuit.
Tailings typically consist of two fractions, sands and slimes. The sand and slimes may be combined and
deposited directly in the impoundment or may be distributed through a cyclone such that the sand fraction
is directed toward the dam while the slimes are directed to the interior of the pond (Merritt 1971).
The fate of radionuclides is of special interest in uranium mill tailings. Radium-226 and thorium-230 are
the principal constituents of concern and are associated with the slime fraction of the tailings. Radon-222
(gas) is also a tailings constituent. The concentrations of radionuclides in the tails will vary depending on
the leach method used (thorium is more soluble in acid than alkaline leaches). Typically, tailings will
contain between 50 and 86 percent of the original radioactivity of the ores depending on the proportion of
radon lost during the operation (Merritt 1971). Other tailings constituents (including metals, sulfates,
carbonates, nitrates, and organic solvents) would also be present in the tailings impoundment depending
on the type of ore, beneficiation methods, and waste management techniques. Table 3.13 below provides
an overview of typical characteristics of uranium mill tailings.
ISL wastewater bleed solutions and lixiviant leaching solutions constitute the major source of wastes
directed to lined evaporation ponds at ISL facilities. These solutions consist of barren lixiviant and
usually have elevated levels of radium; other contaminants (metals, salts) are limited to what may have
been dissolved by the lixiviant or contaminants in solutions used for beneficiation. Barium chloride is
added to the evaporation ponds which, in the presence of radium, forms a barium-radium-sulfate
precipitate. This precipitate forms the majority of the sludges in the settling/evaporation ponds at ISL
operations. Alkali chlorides and carbonates are other likely constituents (U.S. EPA 1983b). These sludges
are collected at the completion of mining (unless required sooner) and disposed of at an NRC-licensed
disposal facility. Information regarding the radionuclide levels of the evaporation ponds can be found in
Appendix V.
ISL operations typically store spent ion exchange resins with waste in labeled containers prior to disposal
at an NRC-licensed disposal facility. Conventional mills would typically dispose of spent ion exchange
resins in the tailings impoundment. Reverse osmosis brines, acid/alkaline leaching, solvent extraction,
stripping and precipitation wastes and materials also are disposed in tailings impoundments.
6 Gangue is defined as the valueless minerals in an ore; that part of an ore that is not economically desirable but
cannot be avoided in mining. It is separated from the ore minerals during concentration.
3-29

-------
Table 3.13. Typical Characteristics of Uranium Mill Tailings
Particle sizes, chemical compositions, and radioactivity levels are presented in this table".
Individual mill impoundment materials can and will vary dependent on ores
and mining or extraction processes used.
Tailings
component
Particle size
(nm)
Chemical
composition
Radioactivity
characteristics
Sands
75 to 500
Si02 with <1 wt % complex silicates of Al, Fe, Mg,
Ca, Na, K, Se, Mn, Ni, Mo, Zn, U, and V; also
metallic oxides
0.004 to 0.01 wt%U3084
Acid leaching :c 26 to 100
pCi 22<5Ra/g; 70 to 600
pCi 230Th/g
Slimes
45 to 75
Small amounts of Si02, but mostly very complex
clay-like silicates of Na, Ca, Mn, Mg, Al, and Fe; also
metallic oxides
U308 and 226Ra are
almost twice the
concentration present in
the sands
Acid leaching:c 150 to
400 pCi 226Ra/g; 70 to
600 pCi 230Th/g
Liquids
d
Acid leaching: pH 1.2 to 2.0; Na+, NH4+, S04 2, CI,
and P04 3; dissolved solids up to 1 wt %
Alkaline leaching: pH 10 to 10.5; C03 2 and HCO3;
dissolved solids 10 wt %
Acid leaching: 0.001 to
0.01% U; 20 to 7,500 pCi
226Ra/L; 2,000 to 22,000
pCi; 230Th/L
Alkaline leaching: 200
pCi 22<5Ra/L; essentially
no 230Th (insoluble)
Source: U.S. DOE (1997)
a Adapted from information in NRC (1980).
b U308 content is higher for acid leaching than for alkaline leaching.
c Separate analyses of sands and slimes from the alkaline leaching process are not available. However, total 226Ra and
230Th contents of up to 600 pCi/g (of each) have been reported for the combined sands and slimes.
d Particle size does not apply. Up to 70 vol % of the liquid may be recycled. Recycle potential is greater in the alkaline
process.
In addition to Table 3.13, there are many available analyses on uranium mill tailings which have been
placed in impoundments. The reader is referred to the EPA and NRC reports mentioned at the beginning
of this section for descriptions of individual sites. As a recent example, however, the Department of
Energy conducted an environmental evaluation of the former Atlas Uranium Mill near Moab, Utah (U.S.
DOE 2005). In that study, they characterized the mill tailings in the impoundment and vicinity properties
as containing about 12 million tons of contaminated materials, of which approximately 10.5 million tons
were tailings. The mean radium-226, ammonia, and uranium concentrations for the tailings were 516
pCi/g, 423 milligrams per kilogram (mg/kg), and 84 mg/kg, respectively. Other constituents, including
iron, manganese, copper, lead, molybdenum, and vanadium, were present in lesser amounts. The pH
values of the tailings were near neutral but had zones of pH values as low as 2.5 and as high as 10. With
respect to grain size of tailings, approximately half of the material was classified as slimes.
3-30

-------
One matter which has affected some mill operations, and consequently the waste in the impoundments, is
that the NRC has the authority to amend a uranium mill license to allow for disposal of source material
termed "alternative feed". This material, derived from a mining or other operation other than a uranium
mine or uranium ISL operation, contains source material and the mill owner is agreeable to processing it
at the mill to extract uranium. Guidance for amending the license to allow for processing this alternate
feed was issued by NRC (2000a).
Radium-226, thorium-230, and radon-222 (gas), and their decay products are the radionuclides present in
uranium mill tailings that are of principal concern to human health and the environment. Under
UMTRCA, EPA has the responsibility to establish standards for exposure of the public to radioactive
materials originating from mill tailings and for cleanup and control standards for inactive uranium tailings
sites and associated vicinity areas. EPA's regulations in 40 CFR 192 apply to remediation of such
properties and address emissions of radon, as well as radionuclides, metals, and other contaminants into
surface and groundwater. Under provisions of the Clean Air Act, operators of uranium mills must comply
with EPA's radon emission requirements in 40 CFR 61, Part W, including providing an annual report to
the Agency on their adherence to the regulations. The NRC or its Agreement States license uranium mills.
Under statutory requirements of the AEA and UMTRCA, NRC has issued regulations in 10 CFR Part 51
to provide for environmental protection for domestic licensing and related regulatory functions, while
those in 10 CFR Part 20 cover radiation protection from hazards of mills and their wastes, and 10 CFR
Part 40 cover uranium source licensing provisions. NUREG 1620 (U.S. NRC 2004) provides guidance for
the approval of reclamation plans of active uranium mills (reclamation of uranium mill tailings
impoundments is covered in Chapter 4 of this report).
As part of those requirements, tailings piles must have a cover designed to control radiological hazards
for a minimum of 200 years and for 1,000 years to the greatest extent reasonably achievable. It must also
limit radon (Rn-222) releases to 20 pCi/m2/s averaged over the disposal area. Radon release limitation
requirements apply to any portion of the tailings disposal sites unless radium concentrations do not
exceed five pCi/g in the first 15 cm below the surface, and 15 pCi/g in layers more than 15 cm below the
surface.
3-31

-------
Chapter 4. Uranium Mine and Extraction Facility Reclamation
This chapter is not intended to serve as guidance, or to supplement EPA or other agency environmental
requirements. Instead, it is an outline of practices which may or have been used for uranium site
restoration.
Mining reclamation is the act of returning a mine to a long-term stable condition, or its original contour to
ensure the safe reuse of the site by both current and future generations. When possible, a reclamation plan
aims to return the affected areas to previously existing environmental conditions. Differing views as to
what is an acceptable environmental condition for reclaimed mining sites explain the varying regulatory
requirements for uranium mining sites. The existence of bonding requirements and/or financial guarantees
in the cases where private parties are involved in the mine may also play an important role in determining
the extent of reclamation. Extraction facilities licensed by the NRC or its Agreement States are required
to have bonds sufficient to allow a third party to reclaim the property should the company holding the site
fail. Additionally, regulatory requirements affect selected reclamation techniques, as some techniques
may be adequate to meet less stringent requirements, but will not be suitable for more restrictive
requirements. In some cases, the remoteness and aridity of a site and reduced risk for human exposure
may affect decisions on whether a site is in need of reclamation, or the extent to which it is reclaimed, if
at all.
When a uranium mine, mill, or other uranium extraction facility has exceeded regulatory requirements for
radiation control, or has had an unauthorized release of metals or other contaminants, the cleanup or other
methods used to remove or contain the contamination is termed remediation. Remediation of a source of
contamination may be a short term response or an interim step in the long-term reclamation of the site
Site reuse is a significant issue for radiation sites. The extent to which a uranium mine site can be reused
for other purposes where humans may spend periods of time for work, recreation, or even residential
purposes is highly dependent on the extent of cleanup and removal of the potential for radiation exposure.
Therefore, the end state of reclaimed uranium sites and the techniques used to achieve the end state, will
vary on a site-by-site basis, and dependent upon the regulatory agencies involved. However, most of what
is described in this chapter is process oriented, rather than regulatory in nature, and much of it is derived
from the Nuclear Energy Agency's (NEA) and IAEA's joint publication Environmental Remediation of
Uranium Production Facilities (NEA/IAEA/OECD 2002) rather than any single set of federal (including
EPA) or state requirements. Appendix VI provides information on federal and state agency regulatory
requirements for reclamation and remediation of these facilities.
A number of handbooks and guides provide much more detailed information on mine site reclamation,
including The Handbook of Western Reclamation Techniques (Ferris et al. 1996), Handbook of
Technologies for Avoidance and Remediation of Acid Mine Drainage (Skousen et al. 1998/ Abandoned
Mine Site Characterization and Cleanup Handbook (U.S. EPA 2000d), EPA's National HardrockMining
Framework (U.S. EPA 1997b), and Environmental Handbook: Effects of Mining on the Environment and
American Environmental Controls on Mining (Marcus 1997).
While this chapter does include some discussion of reclamation techniques applicable to uranium
extraction facilities as background information, reclamation of uranium extraction facilities are governed
by the NRC's regulations. Readers interested in finding out more on this topic should consult NRC
guidance documents such as Standard Review Plan for the Review of a Reclamation Plan for Mill
Tailings Sites Under Title II of the Uranium Mill Tailings Radiation Control Act of1978 (U.S. NRC
4-1

-------
2004), Standard Review Plan for In Situ Leach Uranium Extraction License Applications (U.S. NRC
2003), Design of Erosion Protection for Long-term Stabilization (U.S. NRC 2002), andNMSS
Decommissioning Standard Review Plan (U.S. NRC 2000b).
Although most conventional uranium mine sites in the U.S. are in rural areas remote from population
centers, many have also been located in close proximity to or within communities, such as parts of the
Navajo Reservation in New Mexico, or may be accessible to recreational visitors on federal lands (see
Volume II of this report, U.S. EPA 2006a), and a few have been subject to Superfund cleanups. Thus, in
some instances, uranium mine sites can result in environmental impacts, which may include potential
public exposure to radon and radiation; contamination of groundwater and surface water supplies (via
acid drainage and the mobilization of heavy metals); natural habitat disturbance; increased instability of
the land such as erosion and slope stability failure; and the remaining physical safety hazards. Left
exposed to the environment, these sites could pose hazards to the local community and biota, and the
radioactive wastes could be subject to potential misuse as building materials.
This chapter attempts to cover available uranium reclamation techniques and to summarize some
processes for remediating a uranium mine or extraction facility. The discussion that follows breaks the
reclamation process into two forms of uranium mining and extraction wastes: the waste products from
open-pit or underground mines (which may include TENORM for which EPA, federal land management
agencies, Tribes, and states have jurisdiction) and the waste products from ISL, heap leaching, and
milling (which are regulated by the NRC or its Agreement States) as byproduct material. Several types of
wastes generated need reclamation, and the wide disparity in waste management practices over the years
has resulted in diverse conditions at various mining and extraction sites.
Uranium mining and extraction facilities being reclaimed now are mostly those that have current owners,
which are primarily ISL operations (under license to the NRC or its Agreement States); conventional
mines that were either closed or in suspension with a current or successor owner; or abandoned mines
with or without a current or successor owner. In many cases, federal, state, Tribal, or local government
agencies are involved in managing or requiring the reclamation process to begin.
Characterizing a Mining Site
Site characterization is the first step required in the remediation and reclamation of former uranium
mining facilities. Data on site properties and conditions form the basis for current environmental
assessments, risk analyses, decommissioning plans, reclamation programs, monitoring programs, and
final public use of the site. Data quality objectives and quality assurance and quality control (QA/QC)
procedures may or may not be in place before the data are collected. Mine age, management, and
regulatory practices in place during the operation of each mine, especially some older unreclaimed mines,
may vary significantly. Thus, the requirements for QA/QC issues can also vary significantly, depending
on requirements of the regulatory agencies involved.
The surface and mineral ownership of a site will play an important part in site reclamation and
remediation. The land status will partially determine the regulatory regime. Whether the site is on Tribal,
federal, state, acquired or private lands, or a combination (split estate) will affect many actions.
Ownership or stewardship will also be an important factor in financing reclamation and/or remediation.
This will also identify the regulatory regime and the possibility of developing partnerships to resolve
conflicts and ensure all stakeholders are involved. Identifying current land uses will also drive decisions.
4-2

-------
Many site factors can influence the reclamation of a mining site, including topography, geology,
hydrology, hydrogeochemistry, climatology, ecology, operating characteristics, radiological
characteristics, and socioeconomic characteristics. For example, the topographical setting (whether the
site is located in a valley, a plain, or on a hillside) can affect a site's hydrology and climate. Knowledge of
a site's climatology, hydrology, and hydrogeochemistry is needed for assessing its impacts on water
bodies in the area. In turn, these impacts may influence decisions on strategies and techniques for
reclamation.
Climatological and hydrological characterization includes annual and monthly precipitation, annual and
monthly temperature patterns, annual and monthly wind speed and storm patterns, distribution of surface
water bodies, and data on evapotranspiration rates. Hydrological and hydrogeochemical characterization
includes identification of aquifers, impermeable strata and depths to water tables, groundwater contours,
hydraulic gradients and flow rates, ground and surface water quality, and changes in surface- and
groundwater characteristics overtime.
Understanding a site's ecology is also important to its characterization. Understanding the flora in the area
is important in revegetating the site, and understanding the fauna in the area and their seasonal habits is
important in developing a reclamation plan that will have minimal impact on the ecology.
A site's operational and radiological characteristics are of prime importance in its reclamation. The
historical type of mining, mine layout, and extraction methods will affect the location and types of wastes
present, and knowledge of how the mine operated can improve reclamation procedures utilized.
Geotechnical aspects of the mine, including its stability, will help determine if certain reclamation options
will endanger the workers, and radiological characteristics determine how much reclamation must be
conducted.
As mentioned above, having data on radiological background conditions is very important in the
development and design of any remediation and reclamation plan. The average natural background dose
in the United States is about 300 mrem/year, much of that originating from naturally occurring
radionuclides that include uranium and thorium isotopes. Sites selected for uranium mining will generally
have higher levels of natural background. Radiation surveys for establishing background can help
determine statistically appropriate reference levels of natural soil background in areas uncontaminated by
human activity. This information can aid in establishing the extent of any additive man made
contamination, determining site related impacts, and assessing remediation goals at or above background
radiation levels (U.S. EPA et al. 2001; Eisenbud and Gesell 1997; NCRP 1987b).
Off site characterization is extremely important too as both natural and human factors may have resulted
in dispersion of dusts, rock, liquid, refuse or other wastes contaminated with radionuclides or other
pollutants beyond the borders of a mine or its related facilities. Transport of ore and waste rock to other
locations away from a mine are not uncommon, for example the creation of an ore transport station for
ore produced by several mines in a common area. In this regard, reconnaissance walking, aerial, and
radiation surveying may provide initial evidence of the need for more detailed evaluations. Sampling of
water and soils off site may also provide evidence of contaminant releases. Computer modeling of
collected data, and calculations of potential transport pathways may guide more detailed sampling and
surveys to characterize and identify how far and in what directions radionuclides, metals, or other
contaminants have moved or been taken away from the mine site. Examples of two recent reconnaissance
radiation surveys conducted by EPA in areas off site of uranium mines include U.S. EPA and USACE
(2000) on the Navajo Reservation, and Dempsey et al. (1999) on the Spokane Indian Reservation.
4-3

-------
When releases of contaminants have occurred off site of uranium mines, they may be subject to
remediation actions of federal, Tribal, or state governments in accordance with their statutory and
regulatory authority (see Appendix VI). In the case of the Spokane Indian Reservation in Washington
state, a radiation survey conducted by EPA identified where uranium ore and related materials had spilled
out of trucks driving off site from the Midnite Mine to the Dawn Mill. The mining company agreed to
remove the spilled ore and remediate the sites. The work was completed in March 2005.
Sometimes, it is possible to locate original pre-mining exploration survey radiation data, which can help
in establishing background levels. Surveying techniques for performing radiological characterization
include direct measurement and scanning with radiation survey instruments, and site sampling followed
by lab analysis. Direct measurement and scanning are best suited for determining total surface activities.
However, these measurements in some cases cannot be used for accurately determining reclamation or
remediation goals. In these cases, sampling followed by lab analysis may be best suited for
characterization, but extensive sampling can become very expensive. Protocols and procedures for final
site surveys are detailed in the Multi-Agency Radiation Survey and Site Investigation Manual(MARSSIM)
(U.S. EPA et al. 2001). An important issue in a radiation site survey and particularly for abandoned
conventional mines, and discussed in the MARSSIM, is determining what constitutes background levels
of radiation to ascertain what changes may have occurred at the site due to human activity, and attempting
to distinguish the changes from natural background radiation.
In those instances where mines are located near populated areas, socioeconomic characteristics can
influence methods and clean up goals for mine reclamation. Final land use generally takes into account
future human and environmental exposures from the reclaimed site.
The Reclamation Process
TENORM bearing overburden, waste rock and other materials at sites of former uranium mines that are not
in compliance with applicable criteria and standards may need remediation depending on requirements of
regulating and land use management agencies. The objectives of remediation, dependent on the federal,
state, Tribal or even local requirements, may include removing potentially harmful effects on the
environment and human health, to render impoundments stable over prolonged periods of time, and
ensure that the sites are established with natural self-sustaining vegetation if possible. In addition to
characterizing sites, the following information is generally gathered to develop the final plan for
remediation and public use of the land: agreed final land use; physical characteristics, such as tonnage and
area of rock piles; maximum area that can be used for final disposal and maximum height for contouring;
maximum permitted slope angles; erosion characteristics for proposed combinations of waste rock and
possible limitations on use of erosion control structures of final capping; availability, quantity, and quality
of soil for use in revegetation; and experience with revegetation of similar rock types in the region.
4-4

-------
Overburden and Waste Rock Reclamation
Overburden and waste rock from mining operations are usually placed above ground in piles. An
important decision that is usually made first for reclamation is whether the waste can be placed back into
the mine excavation, either an open-pit mine, or underground mine. Often this decision will depend on the
presence of water at the site, and whether leaching of contaminants and radionuclides from waste placed
back in the excavation is likely to occur. In many instances, the mine may have partially collapsed,
making it impossible to return all wastes to the original workings, which would then require different
reclamation or disposal methods for the remaining materials. In some cases, such as the Lathrop Canyon
mines in Canyonlands National Park, Utah (see Appendix III), a decision was made by the National Park
Service not to reclaim the abandoned mines but just bar the mine opening with wire, and post radiation
signs to keep members of the public out of the workings. This decision was made due to the remoteness
of the mine site, low visitation rate, and anticipated low risk to the public and environment from radiation
at the site (Burghardt et al. 2000). In other sites, land management agencies have returned waste rock to
the underground mine, then placed barriers at the mine portal which allow bats to enter and leave freely
for roosting.
In those cases where mine waste piles have either been returned to an original open-pit excavation, or left
in place, reclamation has generally been implemented by installation of a dry-cover system. The first step
in constructing a dry-cover for overburden and waste rock piles is to recontour the above-ground
materials. This action improves both the long-term stability of the vegetative cover and landscape
integration. In doing so, steps are usually taken to ensure that all settling has occurred prior to re-
contouring, to prevent depressions on the surface that allow water to collect and ultimately infiltrate the
waste pile, and to mediate unsuitable slope angles that promote erosion. There are always exceptions. In
semiarid environments, leaving some engineered rills, depressions, or berms has aided in creating micro-
environments and holding water, on a small scale, for revegetation (Leshendok 2004).
A suitable site usually is designed to last far into the future, though regulatory controls for most mines
end once the facility has been closed. Closure designs may recognize that the radionuclide hazards may
exist on the order of hundreds to thousands to millions of years, due to the long half-life of the
radionuclides involved, and incorporate the impacts of weathering to prevent spreading of radiation.
Designs commonly are based on human and societal abilities to maintain regulatory controls and not on
the period of the hazard's existence. Capping materials are not usually a source of additional pollution and
are generally compatible with the agreed final land use. Water management techniques commonly are
designed to divert surface water away from the impoundment, treat surface precipitation on the
impoundment for suspended solids only, and treat water draining from underground mine areas for
extended periods of time.
The last steps for reclamation generally are revegetation and maintenance. Revegetation improves the
long-term stability of the reclaimed land to integrate with surrounding undisturbed land, strengthens
resistance to erosion, and limits net infiltration of precipitation by enhancing evapotranspiration. While
revegetation can be allowed to develop naturally, one technique is hydro-seeding, which spreads
suspended seeds in nutrient solutions with added organic gels. This may achieve good results in the
presence of some soil; though its use in many areas with only rock, or extreme aridity, has been
unsuccessful. In cases where the topsoil generates acid, special treatment with lime may be necessary.
The use of sewage treatment plant biosolids as a growth medium has been tried successfully on other
types of mines and could be used for uranium mines as well.
4-5

-------
While passive controls are usually preferable, maintenance may be required to cope with surface
disturbance during the first few years, such as local erosion and settling. Maintenance efforts may include
surveying the integrity of the surface cover and intervening to repair detected damage to vegetation.
Heap-Leaching Reclamation
The heap-leaching process is not currently in use by the U.S. uranium industry, but has been used in the
past. Wastes derived from this method, regulated as byproduct material by NRC or its Agreement States,
form piles that if not sent to uranium mill tailings impoundments for disposal, would need to be reshaped
for proper integration into the landscape for reclamation. Many heap-leaching piles were accompanied by
drainage systems that could be preserved for remediation purposes. In some select cases, the heap-
leaching pile would be flushed to further remove all uranium and other valuable substances prior to
considering the pile as waste. Once the pile is considered waste, the reclamation technique for heap-
leaching waste has been contouring for stabilization, and capping. Capping further reduces leaching by
reducing water infiltration rates, preventing the dispersion of radioactive material by water and wind
erosion, decreasing radon emanation rates, and reducing direct exposure to gamma emissions. Under
NRC and Agreement State controls, such sites would need to meet current environmental protection and
radiation protection decommissioning standards for protection of groundwater and the public. In some
cases, the heap-leaching waste could be used as a suitable first cover for mill tailing wastes, if the
properties of the waste are not too acidic.
Mill Tailings Reclamation
Remediation of mill tailings sites is closely affiliated with reclamation of uranium mines. Mill tailings
have been regulated as byproduct materials by the NRC or its Agreement States, and the Department of
Energy (see Appendix VI), under the requirements of UMTRCA. Decommissioning of uranium mills
follows the environmental protection standards of EPA, and licensing and closure regulations and
guidances of NRC or its Agreement States. For at least two sites, mill tailings were stabilized in an
engineered cell within a former uranium mine pit on the mill site. Internationally, two types of systems
have been used for close-out of tailings impoundments to prevent radon emanation: dry-cover and water-
cover systems. Only the dry-cover system is used in the U.S.; however, for information purposes only, the
wet-cover system is also described briefly.
Dry-Cover Systems
A dry-cover system utilizes the following steps: (1) removal of free water and stabilization of the surface,
(2) recontouring and landscaping of above-ground tailings facilities, (3) capping, and (4) revegetation (if
possible) and maintenance. Tailings are usually disposed of as slurry, and water collects on the surface
over time as the tailings consolidate and settle. In cases where the tailings have been allowed to spread
without containment, physical relocation for consolidation purposes may be preferable. Many mill tailings
impoundments have simply been capped with dry rock without revegetation.
Once the containment area has been determined to be acceptable, the water is generally pumped off the
tailings, and a cover applied. One method of improving the drainage of tailings is to insert vertical wick
(cords or fibers that draw liquid to them) drains, which often allows the tailing mass to reach a lower,
final water content than can be achieved by natural drainage. An alternate way of enhancing dewatering
of the tailings is to apply a thin layer of high-density cover material. For example, using a layer of
4-6

-------
synthetic geotextile and an iron netting increases the surface stability and prevents cracks by compressing
the tailings to expel water.
The second step, recontouring the above-ground tailing facilities, improves both the long-term stability of
the cover and landscape integration. This step requires that all settling has occurred prior to recontouring.
In many cases, particularly for uranium mills, due to arid climate and lack of natural soil, revegetation is
not possible and a rock cover may be installed. A principal standard for installation of such a rock cover is
U.S. NRC (2002) NUREG-1623, Design of Erosion Protection for Long-term Stabilization. The
installation of a suitable cap not only covers the waste material, but also prevents fugitive air emissions by
covering the particulate that could be mobilized through air currents. The same cap design, water
management, re-vegetation, and maintenance issues that apply to waste pile remediation apply to
placement of a dry-cover system for tailings remediation.
Water-Cover Systems
While used in Canada and Europe, and in isolated instances for other types of mines in the U.S., water
cover is not viewed as an acceptable means of remediation for uranium mill tailings in the U.S., is not
permitted under NRC regulations unless approved as temporary water covers (groundwater evaporation
ponds), and should not be viewed as EPA recommended procedures. The methods used in other countries
are site specific and dependent on environmental impacts, land use requirements, etc. The discussion
below is for information purposes only.
A water-cover system completely immerses the waste with a sustainable, thin layer of water. Its
objectives are similar to those of a dry-cover system, in that it seeks to stop wind erosion of the dry
beaches, reduce radon emanation, provide a barrier to intrusion of the tailings, and prevent acid formation
in cases of acid-generating tailings. Covering the tailings with water can prevent contact with atmospheric
oxygen and foster the development of anaerobic conditions, which can reduce the mobility of many
contaminants of concern. To be considered for a water-cover remedy, a facility may either be an above-
ground impoundment where slurry has been allowed to settle, with the slimes settling slowly in the center
of the decantation pond, or a below-grade site in open-pits where tailings have been transported as a
thickened paste and disposed of.
This technique has several potential problems, including sustaining the water cover, preventing human
and biota intrusion from ingesting the water cover, and preventing further contamination of other water
bodies through infiltration. A principal issue is mobility of uranium and other radionuclides, especially in
either acidic or alkaline waters. As with all potential remediation techniques, the likely effectiveness of
techniques such as this need to be seriously evaluated prior to remediation design.
Other Approaches
Internationally, tailings have also been disposed of in natural lakes. Reclamation in those cases focused
on ensuring that the tailings would remain contained by the addition of capping with sand and rock. Water
quality monitoring programs for lakes have also been implemented in those countries where this disposal
method has been used. Such methods have not been approved by the EPA. Tailings that have been placed
below ground (in the mine) during operations have provided a long-term management solution from the
viewpoint of reducing potential radiation exposures to members of the public. However, the possibility of
leaching and suffusion (spreading) by permeating groundwater may need to be taken into consideration.
Reclamation and remediation efforts vary based on site specific characteristics, impacts on the
environment, and available resources. Options employed for prevention of leaching and suffusion into
surface and groundwaters include sealing open mine shafts and creating underground barriers by injecting
grouts.
4-7

-------
The Wastewater Problem
Water is one of the principal pathways for dispersal of uranium mining pollutants into the environment.
Water is contaminated by surface runoff from overburden and waste rock piles, seepage through
overburden and waste rock piles, and other actions where mining waste comes in contact with water. The
radioactivity is derived from uranium, thorium, radium, lead and daughter products either dissolved or
suspended in water. Where pyrite and other sulfidic minerals are present, acidic solutions may be
generated. Acid generation, also known as acid mine drainage or acid rock drainage, is a concern of
several types of mining. The acidic solutions, which increase the mobility of heavy metals and
radionuclides in the ore, require neutralization before being discharged into the environment. Also present
in the contaminated water may be nitrates, nitrites, and ammonia originating from the residue of
explosives used. The composition of the wastewater is determined by the ore type and grade, and by the
process technology used to mine the ore.
Pit water, or pit lake water, is water which has filled an open-pit mine excavation, usually derived as
water from underground workings of the mine. As a subset of wastewater, pit water may represent the
largest volume of wastewater present from the existence of uranium mines. Pit water can vary greatly in
the concentration of contaminants present, and the water in some pit lakes may even meet EPA drinking
water standards (Leshendok 2004). However, the resulting water may also have the same general
characteristics as other wastewater generated by contact with mining waste or uranium ore. Pit lakes have
increasingly become a concern of some state regulators in that these waters are generally open to the
public and terrestrial and avian life. For many of these waters, remediation may be a delicate tradeoff due
to the vast quantity of the water and the limited tools available for remediation. In some instances the
regulatory body may acknowledge an inability to meet human health water quality standards and may
refer to other achievable water quality standards such as those sufficient to sustain livestock. The
techniques for remediation of these waters are included in the discussion of the techniques that follow.
Setting of quality objectives for aquifers and the surface water courses are established according to
federal regulatory requirements, land-use plans, as well as state, Tribal and local rules. There are specific
EPA groundwater discharge standards for uranium, thorium, and vanadium, as well as other types of hard
rock mines (see Appendix VI), and many states have used these to establish their own standards, with
discharge permits required for mines in accordance with the Clean Water Act. Acceptable treatment
technologies for mine reclamation are approved by state, Tribal and/or federal agencies (depending on
land ownership) according to the nature of the contaminants, their concentrations, and the desired effluent
levels. A general objective of regulating agencies for mining water treatment is to produce an acceptable
water quality of the discharge with low volumes of residues.
Processes for Treating Uranium Ore
When water comes in contact with uranium bearing ore either naturally in the ground, or when extracted
under license by regulated processes, several oxidation reactions take place. The end product of these
reactions is uranium sulfate (U02S04), which creates uranium cake, sulfuric acid, and ferrous sulfate,
which are the major wastewater contaminants needing treatment. Additionally, the following chemicals
can be generated, either purposely or inadvertently, by chemical reactions occurring with the ore releasing
additional contaminants to the wastewater:
•	Bicarbonates generated due to treatment of the acidic water with lime.
•	Sulfates generated from the oxidation processes described above.
4-8

-------
•	Chlorides added to process water as a stripping agent in the solvent extraction process from back-
washing of ion-exchange resins.
•	Nitrates generated from explosives used for rock blasting and fertilizers used in re-vegetation.
•	Nitrites and ammonium generated from the degradation of organic pollutants.
•	Calcium generated as a residue of water treatment with lime.
•	Sodium generated from the solvent-extraction and ion-exchange processes.
•	Iron generated from the oxidation of pyrite (FeS2) and other ferrous sulfides.
•	Manganese generated naturally from various weathering processes, but also added as an oxidant
in some leaching processes.
Water Treatment Techniques
Treatment of contaminated mine wastewater is usually required, with release concentrations being
dictated by federal and state requirements. While many treatment technologies are capable of achieving
concentrations that are well below regulatory requirements, the accumulation of contaminants in the
sediments may also need to be taken into account. Traditionally, large volumes of contaminated water
being pumped or released from a site (greater than 1,500 feet3 /hr (42.5 m3/hr)) are usually treated by
some form of chemical process though it may also be treated by newer technologies, such as biological
treatment in wetlands, evaporation ponds, and reactive barriers. The residues and sludges remaining from
the wastewater treatment must be disposed of appropriately as determined by the federal, state, or Tribal
land management agency, either on-site or at an engineered low-level radioactive waste disposal cell, or
an approved off-site disposal area. In some cases, depending on the quality of remediated water, standing
bodies of water may be left behind permanently.
Methods used for treating mining wastewater include various types of precipitation methods used to settle
out the contaminants from the wastewater. These contaminants may include radionuclides, metals, and
other inorganic materials. Precipitation methods are the most widely used methods for treating uranium
mining wastewater because they use small amounts of chemicals and are cost-competitive. However, they
also generate large volumes of residues.
Lime Treatment
Lime treatment is the method of choice for treating acidic waters from uranium processing plants that rely
upon sulfuric acid (H2S04) leaching for the extraction of uranium from the ore. It is used for treating acid
mine drainage and seepage water from acid uranium mill tailings and other disposal facilities. This
process adds a 15-20 percent calcium hydroxide (lime, or COH) slurry to the acid effluent to raise the
solution's pH to ten. It blows air into the solution to oxidize ferrous iron, trivalent manganese, and
arsenic, and uranium is precipitated out as calcium diuranate. The effluent can then be discharged with
dilute sulfuric or hydrochloric acid, after pH adjustment to between six and eight. The underflow1
containing the metal precipitates is stored for disposal or further treated.
This process produces underflow or sludge of two percent solids, which may be difficult to dewater.
While the volume of the underflow can be reduced with drum or disk filters or through centrifuges, the
capital and operating costs of this further treatment are high. Another process for minimizing the amount
of underflow of sludge generated is to treat the underflow with a high-density sludge (HDS) process.
The HDS process uses multi-stage treatment processes and recycled underflow to yield a sludge
concentration of up to 15 percent solids.
1 Flowing bottom waters containing dissolved or suspended solids.
4-9

-------
Ferric Chloride Treatment
Although most of the arsenic (As) present in wastewater is precipitated out with lime treatment, the
remaining arsenic levels in the water may still exceed acceptable release limits. If this is the case, ferric
(Fe) chloride (CI) treatment can be added to the slurry during bulk neutralization to precipitate out
arsenic. The reaction:
As043" (aq) + 3H+ (aq) + FeC^	> FeAsC>4 + 3HC1 (aq)
occurs in solutions with a pH of less than seven. Ferric hydroxides also aid in the precipitation process.
This process will yield wastewater with concentrations below 0.1 mg/L
Barium Chloride Treatment
Barium chloride (BaCl2) treatment is widely used in the uranium industry to remove radium at mining
sites. Radium concentrations below 8.1 pCi/L (0.3 Bq/L) can easily be achieved for wastewater
containing sulfate ions. At pH values between six and eight, barium sulfate(BaS04) has a low solubility
and readily precipitates out, co-precipitating radium at the same time. Only 0.00007-0.00013 lb (30-60
mg) of barium chloride per liter of wastewater will achieve 95-99 percent removal of radium. Because
the resulting crystals are difficult to retain, they are usually co-precipitated with other species during bulk
neutralization.
Ion Exchange and Adsorption
Ion exchange is the use of organic or inorganic solids that have chemically reactive sites that are either
positively (cations) or negatively (anions) charged to bind with contamination, thus eliminating it from
the effluent water. Attached to the reactive groups are easily displaceable ions of the opposite charge. The
exchange reaction is driven by the relative concentrations of the competing ions, their electric charge, and
their relative affinity for the exchange site. After treatment of the wastewater, when the resins are spent
(loaded with the ions to be removed from the wastewater), the ions can be recovered by regenerating the
resins by back-washing them with strong acids. Most industrially used ion exchangers are based on
synthetic resins, but inorganic substrates such as zeolites are also used. Ion exchange technology is very
expensive and is best used for specialized, high-selectivity contaminant removal. The advantages of ion
exchange are its ability to treat a wide variety of contaminants and to reduce contaminants to very low
levels.
Ion adsorption is similar to ion exchange, except that it does not attempt to regenerate the resins. An
example of ion adsorption is a uranium-specific, high-molecular polymer called GOPUR 3000, which has
been developed in Germany for removing uranium from wastewater. At pH values between four and
eleven, the reactive surfaces undergo chemical change with the uranyl ion, and the resulting insoluble
matrix precipitates out of the solution. The sludges can then be dewatered using conventional dewatering
techniques.
Bioremediation
In this process, nutrients are added to a water body to increase natural bacterial growth which may then
fix the radionuclides and metals in the bacteria, removing them from the water, and eventually settling to
the bottom.
A recent example of using bioremediation occurred for a pit lake containing over one billion gallons (3.8
billion liters) of water at the Sweetwater uranium property in Wyoming (Paulson 2004).
Sugars, fats, alcohols, and phosphates were added to the water in quantities approaching one million
pounds (about 454 thousand kilograms) over a nine month period. Natural bacteria in the lake
4-10

-------
metabolized the nutrients and respired on dissolved materials in the water in this order: dissolved oxygen,
nitrates, selenium complexes, dissolved uranium. Dissolved metals precipitated on the lake bottom,
increasing the metals concentrations in the bottom sediments. Phosphate addition encouraged the growth
of algae which provided a source of organic carbon to maintain the lake. The finished water quality met
Wyoming state standards for livestock use. Other experiments such as Anderson et al. (2003) have shown
promise with use of metal reducing bacteria, referred to as Geobacter species, which can fix uranium in
groundwater provided sufficient other nutrients are added to the water. In that study, the microbes were
inserted through injection wells to reduce the uranium content of contaminated groundwater at a former
uranium mill site in Rifle, Colorado.
Permeable Reactive Barriers
A method which is being used at some Superfund sites, including those with water contaminated with
uranium, is the permeable reactive barrier. This technology is a constructed permeable wall installed
across the flow path of a contaminant plume, either surface or underground, allowing the water portion of
the plume to passively move through the wall. The barrier allows the passage of water while prohibiting
the movement of contaminants, including uranium, by employing such agents as granular iron, activated
carbon, bacteria, compost or peat, chemicals, and clays. The contaminants will either be degraded or
retained in a concentrated form by the barrier material. The wall could provide permanent containment for
relatively benign residues or provide a decreased volume of the more toxic contaminants for subsequent
treatment. As one example of its use (U.S. EPA et al. 2000), EPA, the U.S. Geological Survey, U.S.
Bureau of Land Management, and U.S. Department of Energy participated in a joint study of the Fry
Canyon site in southeastern Utah for a long-term field demonstration to assess the performance of
selected permeable reactive barriers for the removal of uranium from groundwater. That study found that
reactive iron (zero-valent iron) removed nearly 100% of uranium in water after it had passed 1.5 feet (0.5
meter) through the three foot (one meter) thick barrier.
Wastewater Preventive Strategies
The objective of preventive strategies is to avoid generation of acidic wastewaters and contaminated
water from closed or abandoned mines and to reduce the amount of contamination needing remediation.
The planning of mine closure activities generally gives priority to preventive strategies whenever
possible. Following are some of the preventive strategies and goals that may be applicable:
Underground Mines
•	Avoid mixing good and poor water quality in actively managed mines.
•	Allow flooding of decommissioned mines to reduce the atmospheric oxygen available and the
mobilization of contaminants if there is no connection from the mine to surface or groundwater.
•	Limit groundwater circulation in mines by reducing permeability and hydraulic isolation.
•	Seal shafts, boreholes, and other access routes.
•	Seal fracture and fissure zones.
•	Dam up individual parts of the mine to prevent circulation.
•	Use chemically active backfills to create reactive barriers that reduce contaminant migration.
Surface Impoundments of Mine Waste Materials
•	Divert surface water by developing channels.
•	Cap impoundments to limit infiltration of atmospheric precipitation.
•	Place waste materials selectively to facilitate containment.
•	Install reactive inter-layers (crushed limestone) to control pH.
4-11

-------
•	Encourage the development of anoxic conditions by adding bacterial growth media, such as
manure or wood chips.
Open-pits
•	Install clay seals to prevent infiltration to underlying strata.
•	Add lime to raise pH values.
•	Seal boreholes to prevent infiltration into underlying strata.
•	Backfill the mine pit to avoid accumulation of surface runoff.
Groundwater Protection at ISL Sites
Environmental regulation of ISL systems is overseen by the NRC or its Agreement States (see Appendix
VI); remediation must be conducted to return the groundwater and other systems to as close to pre-
extraction conditions, or to the same class of groundwater use as possible. Groundwater protection
requirements for ISLs are laid out in NRC's NUREG 1569 (U.S. NRC 2003).
Early experiments in production of underground uranium using the ISL method utilized a variety of
different liquids to examine their efficiencies and costs. Used only as a test, it was determined that acidic
solution lixiviants (sulfuric acid, nitric acid, and ammonium bicarbonate) destroyed the ore bearing
material and mobilized many other unwanted materials. Additionally, the restoration activities were found
to be cost prohibitive when attempting to return the aquifer to pre-extraction conditions. Consequently,
the industry has moved toward using ISL oxygen, carbon dioxide, or sodium bicarbonate solutions, which
have become the predominant form of uranium production in the United States, primarily because of their
typically low production costs and expected environmental impacts.
Groundwater restoration is accomplished through a strategy called pump and treat. During ISL, after a
wellfield is exhausted, the aquifer must be restored. During aquifer restoration operations, relatively large
volumes of wastewater are generated. Waste disposal systems at ISL operations usually consist of a
combination of evaporation ponds, deep-well injection, and surface discharge (usually via irrigation).
Evaporation ponds now must be double lined and must incorporate leak-detection and leachate-collection
systems. Pond residues must be shipped off site to approved disposal facilities. Regulations prohibit the
injection of ISL waste into aquifers containing less than 10 g/L of total dissolved solids.
A variety of aquifer restoration processes have been used in the United States. Remediation generally
follows five stages: (1) groundwater sweep, (2) water treatment, (3) reductant addition, (4) circulation,
and (5) stabilization.
Groundwater sweep is initiated when the uranium concentration in the production fluid has dropped to a
level where recovery is no longer feasible. During groundwater sweep, the lixiviant (sodium bicarbonate)
is discontinued, but the water is still pumped through the recovery wells, displacing contaminated water
from the aquifer. As the aquifer is diluted in the concentration of the lixiviant, groundwater sweep
becomes less useful.
During water treatment, contaminated water remaining in the ground is brought to the surface and treated,
and clean water is pumped back into the wellfield. This treatment continues until the groundwater is
restored (normal treatment volumes are two to six times the volume of water in the original aquifer).
4-12

-------
At some operations, the restoration is complete after water treatment. However, since the addition of
chemicals into the aquifer creates an imbalance, the rock must be returned to a reduced state by adding a
chemical reductant, such as hydrogen sulfide. This reducing action usually causes dissolved uranium and
other heavy metals to stabilize at acceptable levels.
Circulation is then conducted in the aquifer, where water in the amount of two or three times the volume
of the aquifer is pumped though the wells to eliminate spatial and temporal variations in water quality.
Finally, stabilization monitoring is conducted to ensure that the well has reached a steady state. If there is
no indication of increasing levels of ground water constituents of concern, the site is released for
unrestricted use.
Evaporite wastes from evaporation ponds are currently disposed of in facilities licensed to receive such
wastes under NRC standards.
Building and Equipment Reclamation
Uranium mine sites usually have very few or no buildings. Any buildings on site are generally temporary
and are easily demolished, though some may be constructed of overburden or waste rock, cemented
together. Demolished building material has generally been bulldozed into one of the open-pits or
sometimes into underground mine portals to be reclaimed and included with the waste rock.
Equipment associated with the conventional mining sites includes mining shaft equipment and frames,
rock ore cars, and other equipment that has come in contact with the ore or waste ore material. Radiation
contamination of this equipment is generally limited to the residue from the transportation and handling
of the mining ore. As such, this equipment has generally been decontaminated by thoroughly washing it
with water or other mild cleaning agents. Following the washing the equipment can be transported to
another site for reuse, depending on its residual radioactivity level, and state requirements.
However, old equipment generally has very little monetary value. In many cases an effective remediation
method has been to simply dispose of the equipment in an open-pit or mine portal and bury it with waste
rock. The resulting waste rock and equipment pit are reclaimed by installing a dry cover. In some cases,
decontaminated equipment may be sent to a recycling mill for processing into new equipment.
Many abandoned mines may have other types of wastes, such as metals, hydrocarbon spills from storage
tanks or vehicle fueling, polychlorinated biphenyls (PCBs) from old or damaged electrical transformers at
a site, lab wastes, explosives, and refuse. Those wastes must be cleaned up in accordance with established
EPA and state rules for hazardous wastes.
Radiation Protection Standards for Reclaiming and Remediating
Uranium Mines and Extraction Facilities
The preceding discussion provided an overview of the process of reclaiming uranium mines and
extraction facilities, as well as means of restoration of surface and groundwaters. These same processes
are generally used for remediation where hazardous materials are being cleaned up at the site or outside
its property borders, except that removal and disposal may be more labor intensive, may require special
protections for workers, property and the public, and require long-term monitoring and stewardship to
ensure that no future releases of the hazardous materials occur. In a particular circumstance, the U.S.
4-13

-------
Congress passed UMTRCA, which established a remedial cleanup program for specific abandoned
uranium mills.
Radium-226, thorium-230, and radon-222 (gas), and their decay products are the radionuclides present in
uranium mill tailings that are of principal concern to human health and the environment. Under
UMTRCA, EPA has the responsibility to establish standards for exposure of the public to radioactive
materials originating from mill tailings and for cleanup and control standards for inactive uranium tailings
sites and associated vicinity areas, as well as operating sites. EPA's regulations in 40 CFR 192 apply to
remediation of such properties and address emissions of radon, as well as radionuclides, metals, and other
contaminants into surface and groundwater. Title I of the Act concerns tailings at inactive uranium
milling and extraction sites while Title II applies to currently operating uranium mill tailings facilities
licensed by the NRC or an Agreement State. More discussion on UMTRCA and associated federal
regulations can be found in Appendix VI, and U.S. EPA (1995a). Among the more important remediation
standards are:
•	The disposal areas must be designed to limit releases of radon-222 from uranium byproduct
materials to the atmosphere so as not to exceed an average release rate of 20 pCi/m2/s. This
requirement, however, applies only to a portion of a disposal site that contains a concentration of
radium-226 that, as a result of uranium byproduct material, exceeds the background level by more
than:
o 5 pCi/g, averaged over the first 15 cm below the surface
o 15 pCi/g averaged over 15 cm thick layers more than 15 cm below the surface.
•	Maximum concentration limits are established for protection of groundwater, although alternative
concentration limits can be established for specific sites by DOE. The EPA standards are (in
milligrams per liter, unless otherwise stated:
Arsenic	0.05
Barium	1.0
Cadmium	0.01
Chromium	0.05
Lead	0.05
Mercury	0.002
Selenium	0.01
Silver	0.05
Nitrate (as N)	10.
Molybdenum	0.1
Combined radium-226 and radium-228	5 pCi/liter
Combined uranium-234 and uranium-238 *	30 pCi/liter
Gross alpha-particle activity (excluding radon and uranium)	15 pCi/liter
Endrin (l,2,3,4,10,10-hexachloro-6,7-exposyl,4,4a,5,6,7,8,8a-	0.0002
octahydro-l,4-endo,endo-5,8-dimethanonaphthalene)
Lindane (1,2,3,4,5,6-hexachlorocyclohexane, gamma insomer)	0.004
Methoxychlor (l,l,l-trichloro-2,2'-bis(p- O.lmethoxyphenylethane))	0.1
Toxaphene (C10H10C16, technical chlorinated camphene, 67-69	0.005
2,4-D (2,4-dichlorophenoxyacetic acid) 2,4,5-TP
Silvex (2,4,5-trichlorophenoxypropionic acid)	0.01
* Where secular equilibrium obtains, this criterion for uranium will be satisfied by a concentration of0.044 milligrams
per liter (0.044 mg/l). For conditions of other than secular equilibrium, a corresponding value may be derived and
applied, based on the measured site-specific ratio of the two isotopes of uranium .
4-14

-------
The NRC or its Agreement States license uranium mills. Under statutory requirements of the AEA and
UMTRCA, NRC has issued regulations in 10 CFR Parts 40 and 51 to provide for environmental
protection for domestic licensing and related regulatory functions, while those in 10 CFR Part 20 cover
radiation protection from hazards of mills and their wastes, and adopt the EPA standards. NUREG 1620
(U.S. NRC 2004) provides guidance for the approval of reclamation plans of active uranium mills.
While EPA has not established radiation protection standards for use in mine reclamation, it has
developed guidance for use in cleanup of radioactively contaminated soils and groundwater primarily for
the Superfund program. The soil standards are based on the use of radiation standards developed under
the UMTRCA program for uranium mills (U.S. EPA 1998, 1997c) while cleanup standards for
groundwater use EPA's maximum contaminant levels established under the Safe Drinking Water Act
(U.S. EPA 2001c). The radionuclide soil cleanup standard for combined radium-226, radium-228, and
thorium-232 is 5 pCi/g. For groundwater cleanup and protection, the EPA drinking water standards for
uranium of 30 (ig/L, and 5 pCi/L for radium are relevant and appropriate.
Costs of Reclaiming and Remediating Uranium Mines and Extraction Facilities
The discussion which follows provides a brief overview of the costs of reclamation and remediation at
uranium mines and extraction facilities (mills, ISL and heap-leach). Analysis of reclamation and
remediation costs at uranium mines and extraction facilities would potentially include costs associated
with the following items: overburden and waste rock piles, heap-leach piles, ore storage and loading
areas, tailings ponds, underground mines, open-pit mines, milling facilities, buildings and infrastructure,
ISL infrastructure, and contaminated soils and groundwater.
Costs of environmental management after closure consist primarily of reclamation and monitoring costs.
For mines, reclamation may include partial or complete backfilling of pits, stabilization of waste rock
piles, appropriate contouring of disturbed land surfaces, and revegetation. Monitoring is a post-closure
cost of some, but not all mines. Since remediation projects vary greatly due in part to ore conditions,
mining and extraction method, climate, remediation scope and objectives (usually as defined by
applicable regulations), and sources and availability of funds, the costs for reclaiming uranium mines also
vary greatly. In those instances where an operating, inactive or abandoned facility has been remediated as
a result of response to releases of hazardous substances under CERCLA or applicable state laws, the costs
may be incrementally larger.
The Department of Energy conducted a summary of cleanup costs for 75 production facilities, including
mining and milling operations of uranium mines, an abbreviated version of which appears in Tables
4.1-4.4. Due to the similarity of the cleanup techniques, costs for remediating uranium milling sites
(under UMTRCA) have been included in Tables 4.1 to 4.3. The costs of reclaiming and remediating the
21 mines included in this survey varied widely, by more than two orders of magnitude in terms of cost per
ton of ore and kg of uranium produced (Table 4.4). Some of this range is attributable to the differences in
acreage of land area disturbed per ton of ore, but much of it is due to the differences in methods of
accounting for cleanup costs. Some of the mines performed contemporaneous reclamation during mining.
Some of those mines charged those costs against operations, while others charged them separately as
reclamation costs.
4-15

-------
The average costs of cleanup of the 21 mine sites included in this survey were $3.01/metric ton (MT) of
ore mined, $2.54/kg of uranium produced, and $29,969/hectare of land disturbed. However, the Day-
Loma mine has exceptionally high costs and skews the averages disproportionately to its total production.
If Day-Loma cost figures are excluded, the Title II average costs drop to $2.77/MT of ore, $2.34/kg of
uranium produced, and $27,900/hectare of disturbance. Costs of reclamation of these sites ranged from a
low of $0.24/MT of ore, $0.18/kg of uranium produced, and $2,337/hectare disturbance to a high of
$33.33/ MT of ore, $23.74/kg of uranium produced, excluding the Day-Loma mine, and $269,531/hectare
disturbance for all 21 mines. The average total estimated cost is $13.9 million per mine.
Table 4.1. Total and Average Production and Costs of Remediation
of TITLE I Uranium Mills and Related Facilities
Title I Mills were abandoned, un-licensed mills operated during the AEC existence.
Number of sites included
26
Metric tons of ore processed
29,100,000
Metric tons of uranium produced
50,624

Average cost of closure, $/MT ore
$50.91
Lowest cost of closure, $/MT ore
$5.00
Highest cost of closure, $/MT ore
$320.25

Average cost of closure, $/kg U
$29.22
Lowest cost of closure, $/kg U
$2.50
Highest cost of closure, $/kg U
$348.42

Average cost of closure, $/curies Ra-226
$48,000
Lowest cost of closure, $/curies Ra-226
$5,000
Highest cost of closure, $/curies Ra-226
$958,167

Average closure cost per site
$56,900,000
Total closure costs of all Title I sites
—excluding groundwater program
$1,480,000,000
Title I Groundwater Program
$215,000,000

Total Closure Costs of all Title I Sites
$1,695,000,000
Source: U.S. DOE/EIA 2000b.
4-16

-------
Table 4.2. Total and Average Production and Costs of Remediation
of TITLE II Uranium Mills and Related Facilities
Title IIMills were mills licensed byNRC or Agreement States in or after 1978.
Number of sites included
28
Metric tons of ore processed
220,000,000
Metric tons of uranium produced
284,088

Average cost of closure, $/MT ore
$2.66
— excluding Shootaring Canyon Mill
$2.62
Lowest cost of closure, $/MT ore
$0.67
Highest cost of closure, $/MT ore
$11.33

Average cost of closure, $/kg U
$2.06
— excluding Shootaring Canyon Mill
$2.03
Lowest cost of closure, $/kg U
$0.45
Highest cost of closure, $/kg U
$14.04

Average Closure Cost per Site
$20,900,000
Total Closure Costs of All Title II Sites
$584,800,000
Source: U.S. DOE/EIA 2000b.
Table 4.3. Total and Average Production and Costs of Reclamation
of All Uranium Mill Sites (Title I and Title II)
Average Closure Cost per Site
$42,200,000
Total Closure Cost
$2,279,800,000
Source: U.S. DOE/EIA 2000b.
4-17

-------
Table 4.4. Total and Average Production and Costs of Reclamation of All Uranium Mines
This table includes mines as well as mill sites.
Number of sites included
21
Metric tons of ore processed
96,900,000
Metric tons of uranium produced
114,803


Average cost of closure, $/MT ore
$3.01
— excluding Day-Loma
$2.77
Lowest cost of closure, $/MT ore
$0.24
Highest cost of closure, $/MT ore
$33.33


Average cost of closure, $/kg U
$2.54
—excluding Day-Loma
$2.34
Lowest cost of closure, $/lb U308
$0.18
Highest cost of closure, $/lb U308
$23.74


Average cost of closure, $/ha disturbance
$29,969
—excluding Day-Loma
$27,900
Lowest cost of closure, $/ha disturbance
$2,337
Highest cost of closure, $/ha disturbance
$269,531


Average Closure Cost per Site
$13,900,000
Source: U.S. DOE/EIA 2000b.
At a similar level of expenditure, remediation by EPA of the Lucky Lass and White King uranium mines
in Oregon under CERCLA was estimated to cost approximately $8 million (U.S. EPA 2001a). The
National Forest Service planned to remediate the Juniper uranium mine in California at a cost of
approximately $2 million (AAPG 2005).
Underground and open-pit mine closures which have not involved remediation or long-term monitoring
have been reported by some organizations as costing significantly less than the above sites, particularly
when overburden, waste rock, and protore have not needed to be disposed off-site, soil contamination is
minimal, sites are relatively small, and water intrusion has not been a problem. For example, the Navajo
Abandoned Mine Lands Agency (Navajo AMLR 2000) expended about $893,000 to reclaim 20 mines
with over 245 mine portals, over 57,000 cubic yards of radioactive mine waste spread over 35 acres of
land, and seven acres of haul road. The average cost per mine would be about $45,000.
On the other hand, remediation actions under CERCLA for spilled ore off-site of a mine can be
expensive. Cleanup in 2005 of 12 sites where ore had spilled off of ore trucks on the haul road between
the Midnite Mine and the Dawn Mill in Washington state, some 18 miles (about 29 km) distant, amounted
to a cost of approximately $357,500 (MFG 2005).
U.S. DOE/EIA (1995) estimated average decommissioning costs for ISL operations were $7 million.
Groundwater restoration accounted for $2.8 million, wellfield reclamation costs were $0.9 million and the
plant dismantling costs came to $0.6 million. Other costs (such as evaporation ponds, disposal wells, and
radiological surveys) averaged $1.2 million. The indirect costs averaged $1.4 million.
4-18

-------
Stewardship and Long-Term Monitoring, Management and Remediation
Radiation from closed sites remains a potential risk concern for thousands of years due the extensive half-
lives of uranium isotopes and their progeny. Even when state-of-the art remediation methods have been
used for stabilizing a site, proof that the methods have been successful can sometimes only be obtained
through long-term monitoring of air and water pathways. Because some uranium mines are developed
where natural accumulations of uranium far exceed normal concentrations in unmineralized rocks, areas
in and around uranium mines have natural, ambient radioactivity that may be hazardous to human health,
irrespective of whether a mine was ever developed.
When mining or extraction facilities are closed, stewardship and monitoring may or may not be required
to ensure that remediation goals have been met. This requirement depends on statutory requirements for
federal, state or Tribal agencies, the nature of the site, and local site conditions. For example, after the
stabilization monitoring phase at NRC or Agreement State licensed/permitted ISL facilities, if there is no
indication of increasing levels of groundwater constituents of concern, the site is released for unrestricted
use. Mines remediated under EPA Superfund oversight can require open ended periodic monitoring until
it is similarly determined that the site can be released. Many mines on federal, state, and Tribal lands in
the western U.S. have been considered closed without need for further monitoring once they have been
reclaimed (or remediated if necessary). Under UMTRCA requirements, reclaimed uranium mill tailings
sites are licensed to the DOE and designed for 1000 years of control.
Stewardship refers to the institutional controls (ownership or governmental) which may be put in place to
ensure that a specific site meets its closure goals. Institutional controls can be either active, involving
some form of continuous or intermittent human activity to maintain the condition of the site, or passive,
which do not require human intervention and have an amount of redundancy built into them to deter or
prevent disturbance of the remediated site. Examples of active controls are air, surface, and groundwater
monitoring; site inspections; ground radiation surveys; and aerial gamma surveys. Examples of passive
controls are land-use restrictions, fences, and signs. The installation of passive controls does not negate
the need for active institutional controls (i.e., monitoring).
Stewardship may also include reclamation goals other than protecting human health and preventing water
pollution. Some may include consideration of providing bat gates for underground mines, ensuring little
or no disruption to wildlife using or passing over the site, staining highwall rock to reduce visual impacts,
and ensuring there are no reclamation impacts on historical or cultural sites. These may be built into
closure requirements for sites.
Monitoring for uranium mining and extraction sites, if required, allows for the assessment of the
effectiveness of the reclamation and remediation efforts. Although requirements may differ, some of the
more common approaches include the following:
•	Site inspections confirm that the integrity of the site has not been disturbed.
•	Geotechnical monitoring, sometimes involving global positioning systems, identifies the site and
determines if any settling, erosion, or movement has occurred.
•	Groundwater monitoring for uranium and other contaminants detects contaminant movement into
groundwater systems.
•	Surface water monitoring detects changes in the quality or quantity of surface water.
•	Air monitoring detects increases in radon and other emissions from the site.
4-19

-------
• Ecological monitoring determines if any of the biota are affected by bioaccumulation of heavy
metals or radionuclides from the remediated site.
There have been situations where long-term active actions may be required to maintain wastewater
treatment facilities or fences, provide for possible future groundwater or air impacts, etc. Several hardrock
mines—both new and abandoned—have had to have long-term planning and funding developed to ensure
that at some time in the future such impacts are properly managed (Leshendok 2004).
The time period over which monitoring can be required depends on a number of factors, not the least of
which is funding availability. Contemporary remediation designs have been developed with a projected
lifetime of 200 or 1,000 years (uranium tailings sites must be designed for 1,000 years of control, and
disposal sites must be designed for 200 years of control). Older sites did not have an established design
parameter for the design of these plans. Site monitoring, if necessary, may initially be conducted every
year. However, if little change is noted, the frequency may be reduced to every other year or even once
every five years. Generally, if the monitoring phase indicates no increasing levels of radionuclide or
pollutant discharge, sites have been released for unrestricted use.
4-20

-------
Chapter 5. Conclusion
Uranium, a naturally occurring element, contributes to low levels of natural background radiation in the
environment, and is found in virtually all rock and soil, as well as groundwater. Contained in a variety of
ore bearing rocks, it can be extracted and chemically converted into uranium oxide or other chemical
forms usable in industry. Uranium undergoes radioactive decay into a long series of different
radionuclides before finally reaching a stable state as lead. These radionuclides each emit alpha or beta
radiation, and some also emit gamma radiation of widely varying energies. Some of these progeny
radionuclides are highly radioactive and can pose significant human health risks, most notably radium and
the radioactive gas radon.
Mining is the process by which mineral and metal bearing ores are extracted from the earth. Protore is
mined uranium ore that is not rich enough to meet the market demand and price. This subeconomic ore is
often stockpiled at the mine site for future exploitation under the appropriate economic or market demand
conditions. Radioactive waste materials for which EPA, Tribal, state, or local government agencies have
statutory authority, that are or could be classified as TENORM from conventional open-pit and
underground uranium mining include overburden (although most overburden is not necessarily enriched
in uranium as is protore), unreclaimed protore, waste rock, evaporites from mine water, mine and pit
water, drill core and cuttings, and refuse. Liquid and solid waste materials generated at heap leaching,
ISL, or uranium mills are considered byproduct that is regulated by the NRC or its Agreement States.
Most uranium mining in the United States took place in the Colorado Plateau region straddling the Four
Corners where Utah, Colorado, New Mexico, and Arizona meet, though more than a dozen states have
hosted uranium mines during the last century. Significant changes in the uranium market price for
uranium after the early 1980s previously resulted in inactivation or closing nearly all mines and uranium
mills in the country. Recent increases in uranium price and demand have resulted in renewed interest in
re-opening mines that were closed or on standby. While some mines focus on extraction of just uranium
minerals, many mines have produced uranium along with a host of other valuable minerals that were
found together in the same rock ore.
The early small mining endeavors generated small quantities of waste typically discarded within a few
to hundreds of feet (100 meters) of the mine opening or pit. Major surface mines tend to disturb large
surface areas from the extent of both the pit and the spoils areas. Generally, tens to hundreds of acres may
be covered by overburden and waste rock. At some sites, as mining progressed, the overburden was used
to backfill mined-out areas of the open-pit in anticipation of later reclamation. Most of the older surface
mines (pre to-mid-1970s) were not backfilled during mining operations, while some of the more recent
mining included modest backfilling operations. The surface area affected by major underground mining
activities generally involves less than about 50 acres (20 hectares).
Waste volumes produced by surface, open-pit mining are a factor of 45 greater than for underground
mining, based on their respective averages. Thus, the amount of overburden and waste rock generated
from open-pit mines far exceeds that from underground mines. The U.S. Geological Survey (Otton 1998)
estimated that the total amount of overburden and waste rock generated by the approximately 4,000
operating conventional mines in its data set is from one billion and nine billion metric tons, with a likely
estimate of three billion metric tons. Overburden and waste rock from surface mines can include huge
boulders that may have been broken down with explosives and heavy machinery into particles ranging
from a micrometer to boulders about three feet (a meter) or more in diameter. The characteristics of
overburden and waste rock from conventional mines depend on the geology of the zone where the ore
was originally mined, and how the waste was subsequently treated. This may ultimately affect the
availability of metals and radioactivity to the environment as contaminants.
5-1

-------
Radionuclide leaching primarily from mine waste piles adjacent to open-pit mines—but also possibly
derived by leaching from mine pit walls or by groundwater infiltration from underlying uranium
deposits—can result in significant levels of radiation in water-filled pit lakes, though some pit waters may
not become very contaminated. Surface and underground mines that intersect aquifers have the potential
to contaminate the aquifers.
In the 1980s, primarily due to cost, ISL operations, which began in the 1970s, displaced surface and
underground mining methods as the principal means of extracting uranium in the United States. In
general, ISL generates small amounts of surface solid waste comprised of: (1) soil and weathered bedrock
material disturbed during surface preparation of the site, (2) liquid and solid waste from drilling of
injection and production wells, and (3) solids precipitated during storage and processing of fluids in
holding ponds. Available data are insufficient to estimate the total amount of solid and liquid wastes
generated by existing and previous ISL operations.
Some uranium mines pose such a hazard that they are Superfund sites. Two uranium mines are on the
National Priorities List, and CERCLA removals were undertaken in 2001 for two houses constructed with
uranium mine waste rock on Tribal lands, and a recent removal action took place in Washington state for
off-site spills of uranium ore materials along a haul road between a mine and a mill. The reclamation and
remediation of uranium mines is an important consideration when contemplating the impact of past and
present uranium mining operations. Data from a Department of Energy/Energy Information
Administration study reveal that the costs of reclamation without site monitoring ranged from a low of
$0.24/MT of ore, $0.18/kg of uranium produced, and $2,337/hectare of disturbance to a high of
$33.33/MT of ore, $23.74/kg of uranium produced, and $269,531/hectare of disturbance for all 21 mines.
The average total estimated cost is $13.9 million per mine. Many smaller mines less than 25 acres (10
hectares), which may constitute the majority of mine-scarred lands currently unreclaimed, especially in
arid regions, may require much lower remediation costs, on the order of $45,000 or lower; this cost would
be incurred to bury waste piles back in a pit or underground mine opening, clean up the soil to lower
radionuclide and metal levels, and close or armor the mine opening with rock.
When conventional mining and uranium extraction facilities are closed, stewardship and monitoring may
be required for long periods of time to ensure that reclamation and remediation goals have been met,
depending on regulatory agency requirements. However, in many cases, once a facility has been
reclaimed and there are no indications of increasing levels of radionuclide or pollutant discharge, it is
considered released for other uses.
5-2

-------
Chapter 6. Bibliography
AAPG 2005—American Association of Petroleum Geologists. Recent Uranium Industry Developments,
Exploration, Mining and Environmental Programs in the U.S. and Overseas. Uranium Committee,
Energy Minerals Division. Tulsa, OK: March 25, 2005. http://emd .aapg .org/technical areas/uranium.cfm
ACAA 1996—American Coal Ash Association. Annual Survey of Coal Combustion Byproduct (CCB)
Production & Use: 1966-1994. Alexandria, VA: ACAA May, 1996.
ACAA 1995—American Coal Ash Association. Solidification and Stabilization of Wastes Using Coal
Fly Ash: Current Status and Direction . Alexandria VA: ACAA, April, 1995.
Ames and Rai 1978—Ames, L., and Rai, D. Radionuclide Interactions with Soil and Rock Media,
Volume 1: Processes Influencing Radionuclide Mobility and Retention, Element Chemistry and
Geochemistry, and Conclusions and Evaluations, EPA 520/6-78-007-a. Las Vegas, Nevada: U.S.
Environmental Protection Agency, 1978.
ANAWA 2006—Anti-Nuclear Alliance of Western Australia. In Situ Leach Mining.
http://www.anawa.org.au/mining/isl.html
Anderson et al. 2003—Anderson R. Vrionis, H Ortiz-Bernad, I. Resch, C., Long, P., Dayvault, R., Sharp
K., Marutzky, S., Metzler, D., Peacock, A., White, D., Lowe, M., and Loveley, D. Stimulating the In Situ
Activity of Geobacter Species to Remove Uranium from the Groundwater of a Uranium-Contaminated
Aquifer. Applied and Environmental Microbiology. Volume 69, No.10. Washington, DC: October, 2003.
Austin 1978—Austin, S., and Droullard, R. Radon Emanation from Domestic Uranium Ores Determined
by Modifications of the Closed-Can Gamma-Only Assay Method. Report of Investigations 8264.
Washington, DC: U.S. Bureau of Mines, 1978.
AVI 1991—AVI. AML Project 16B, George Area. Pre-design Report. Cheyenne, WY: Wyoming
Department of Environmental Quality, Land Quality Division, 1991.
AVI 1990—AVI. Environmental Assessment, Baggs-Poison Basin Uranium AML Project 7D, Carbon
County. Administrative Report. Cheyenne, WY: Wyoming Department of Environmental Quality, Land
Quality Division, 1990.
AVI 1986—AVI. Report of Investigations for AML 13, Shirley Basin. Vol. 1. Cheyenne, WY: Wyoming
Department of Environmental Quality, Land Quality Division, 1986.
Barretto 1975—Barretto, P. Radon-222 Emanation Characteristics of Roads and Minerals in Radon in
Uranium Mining. STI/PUB/391. Vienna, Austria: International Atomic Energy Agency, 1975.
Beck 1989—Beck, H. Radiation Exposures Due to Fossil Fuel Combustion, Radiation Physics and
Chemistry 24 (1989), no.2
6-1

-------
Beck et al. 1980—Beck, H., Gogolak, C. Miller, K., and Lowder, W. Perturbations on the Natural
Radiation Environment Due to the Utilization of Coal as an Energy Source. In Natural Radiation
Environment III, Vol. 2, CONF -780422, pp. 1521-58. Washington, DC: U.S. Department of Energy,
1980
Benes 1990—Benes, P. Radium in (Continental) Surface Water. In The Environmental Behavior of
Radium. Volume I. PP. 373-418, Vienna, Austria: International Atomic Energy Agency, 1990.
Bohert and Gerity 1978—Bohert, J., and Gerity, C. An Economic Analysis of Open-Pit and In Situ
Mining. Mining Engineering 30, No. 10:1140-22. Littleton, CO:. October, 1978.
Brady et al. 1997—Brady, G., Clauser, H., and Vaccari, L. Materials Handbook. 14th ed. New York, NY:
McGraw-Hill, 1997
Brown 1978—Brown, S. Radiological Aspects of Uranium-Solution Mining. Uranium 1 (1978): 37-52.
Burghardt 2003—Burghardt. J. Capitol Reef National Park {Utah): Rainy Day and Duchess Uranium
Mines-Site Characterization (September 2002) Summary results presented at U.S. Department of the
Interior Conference on the Environment. Phoenix, AZ: May 13, 2003.
Burghardt 1998—Burghardt, J. Unpublished field survey descriptions. Lakewood, CO: U.S. National
Park Service, 1998.
Burghardt et al. 2000—Burghardt, J. Graham R. Mesch, M., and Doolittle, R. Uranium Mine Waste
Dump Characterization in Lathrop Canyonlands National Park, Utah. Unpublished Manuscript.
Lakewood, CO: U.S. National Park Service, October, 2000.
Burns and Finch 1999—Burns, P., and Finch, R Uranium, Mineralogy, Geochemistry and the
Environment. In Reviews in Mineralogy, Vol.38. Washington, DC: Mineralogical Society of America,
1999.
Chenoweth 2004—Chenoweth, W. Written communication to U.S. EPA, Office of Radiation and Indoor
Air. Grand Junction, CO: October 4, 2004.
Chenoweth 1998—Chenoweth, W. Oral communication with J. Otton, U.S. Geological Survey, Denver
CO., 1998. Reported in Otton 1998.
Chenoweth 1991—Chenoweth, W. A History of the Uranium Industry in Utah. In Energy and Mineral
Resources of Utah, edited by M.L. Allison. Salt Lake City: Utah Geological Assoc Publication 18, pp.
114-129.
Colon et al. 2001—Colon, C., Jove P., Brady, M., Siegel, M., and Lindgren, E. Historical Case Analysis
of Uranium Plume Attenuation. NUREG/CR-6705 SAND2000-2254. Washington, DC: U.S. Nuclear
Regulatory Commission, Office of Nuclear Regulatory Research, February, 2001.
6-2

-------
Cothern and Rebers 1990—Cothern, C., and Rebers, P. (eds.). Radon, Radium, and Uranium in Drinking
Water. Chelsea, Michigan: Lewis Publishers, 1990.
CRC 1994—CRC. Handbook of Chemistry and Physics. 75th ed. Boca Raton, FL: CRC Press, 1994.
CRCPD 2004—Conference of Radiation Control Program Directors, Part N, Regulation and Licensing of
Technologically Enhanced Naturally Occurring Radioactive Material (TENORM). Suggested State
Radiation Control Regulations Volume I. Frankfort, KY: CRCPD. April 2004.
CRCPD 1994—Conference of Radiation Control Program Directors. Report of the E-4 Committee on
NORM Contamination and Decontamination/Decommissioning. Report No. 3. Frankfort, KY: CRCPD,
April 1994.
DeLaune et al. 1996—DeLaune, R., Pardue, R., Patrick, W., Jr., and Lindau,C.Mobility and Transport of
Radium in Sediment and Waste Pits. Final project report submitted to the South and Southwest Hazardous
Substance Research Center, and conducted under EPA Grant Number R825513. Baton Rouge, LA:
Louisiana Water Resources Research Institute, March 1996.
Dempsey et al. 1999—Dempsey, G., Shura, R., and Harris, J. Radiological Scanner Van Survey Ford-
Wellpinit Road/Midnite Mine Area, Spokane Indian Reservation, September 21-23, 1999. Las Vegas, NV:
U.S. Environmental Protection Agency, Radiation and Indoor Environments National Laboratory,
November 10, 1999.
http://vosemite.epa.gov/R10/CLEANUP.NSF/9f3c21896330b4898825687b007a0f33/ff8fab02b57948588
8256feb00722d21/$FILE/most%20AR%20documents.pdf
DeVoto and Stevens 1979—DeVoto, R., and Stevens, D.,eds. Uraniferous Phosphate Resources and
Technology and Economics of Uranium Recovery from Phosphate Resources, United States and Free
World. 3 vols. Prepared by Earth Sciences, Inc., for the U.S. Department of Energy. Open File Report
GJBX-110(79). Grand Junction, CO: U.S. Department of Energy, 1979.
Dickson 1990—Dickson, B. Radium in Groundwater. In The Environmental Behavior of Radium, Volume
I. pp. 335-372, Vienna, Austria: International Atomic Energy Agency, 1990.
Eadie and Kaufmann 1977—Eadie, G., and Kaufmann, R. Radiological Evaluation of the Effects of
Uranium Mining and Milling Operations on Selected Ground Water Supplies in the Grants Mineral Belt,
New Mexico. Health Physics, Vol. 32:231-241, 1977.
Edwards and Atkinson 1986—Edwards, R, and Atkinson, K. Ore Deposit Geology. New York, NY:
Chapman and Hall Limited, 1986.
Eisenbud and Gesell 1997—Eisenbud, M., and T. Gesell. Environmental Radioactivity from Natural,
Industrial, and Military Sources. San Diego, CA: Academic Press, 1997.
EPRI 1988—Electric Power Research Institute. High-Volume Fly Ash Utilization Projects in the United
States and Canada." CS-4446, 2d ed. Palo Alto, CA: EPRI, March 1988.
6-3

-------
ESRI 2001—Environmental Systems Research Institute, Inc. ESRI Data & Maps 2000: An ESRI White
Paper. Redlands, CA: ESRI, August 2001.
Ewing 1999—Ewing, R. Radioactivity and the 20th Century. In Reviews in Mineralogy, vol. 38:
"Uranium, Mineralogy, Geochemistry and the Environment", ed. P.C. Burns and R. Finch, pp. 1-23.
Washington, DC: Mineralogical Society of America, 1999.
Facer et al. 1978—Facer, J., Larson, W., and Leader, W. Formidable Challenges Await Uranium Mining.
Mining Engineering 30, no. 10:1, 423. Littleton, CO: October, 1978.
Ferris et al. 1996—Ferris, F., Kleinman, L., Steward, D., Stowe, R., Vicklund, L., Berry, J., Cowan.,
Dunne, C., Dunne, R., Fritz, D., Garrison, R., Green, R., Hansen, M., Jones, C., Jones, G., Lidston, C.,
O'Rourke, M., Postovit, B., Postovit, H., Shinn, R., Tyrell, P., Warener, R., and Wrede, K., Handbook of
Western Reclamation Techniques. Denver, CO: Technology Transfer Center, Western Regional
Coordinating Center, Office of Surface Mining, Reclamation and Enforcement, December 31, 1996.
http://www.ott.wrcc.osmre.gov/librarv/hbmanual/westrecl/front-matter.pdf
Finch 1998—Finch, W. Unpublished compilation of uranium production data from U.S. Geological
Survey files. 1998.
Finch and Murakami 1999—Finch, R., and T. Murakami. Systematics and Par agenesis of Uranium
Minerals. In Reviews in Mineralogy, vol. 38: "Uranium, Mineralogy, Geochemistry and the
Environment", ed. P.C. Burns and R. Finch, pp. 91-179. Washington, DC: Mineralogical Society of
America, 1999.
FIPR 1995—Florida Institute of Phosphate Research. Microbiology and Radiochemistry of
Phosphogypsum. Publ. No. 05-035-115. Bartow, FL: FIPR, May 1995.
Fisher 2003—Fisher, E. Personal communication. U.S. EPA Office of Radiation and Indoor Air, Indoor
Environments Division. Washington, DC: 2003.
FPE 1988—Forsgen-Perkins Engineering. Regional Planning Document, AML Project 16, Gas Hills,
Wyoming Uranium Mining District, Fremont and Natrona Counties. Administrative Report. Cheyenne,
WY: Wyoming Department of Environmental Quality, Land Quality Division, 1988.
Frissel and Koster 1990—Frissel, M. and Koster, H. Radium in Soil. In The Environmental Behavior of
Radium , Volume I. pp. 323-334, Vienna, Austria: International Atomic Energy Agency, 1990.
FR 2000a—Federal Register. Vol. 65, no. 236, December 7, 2000. National Primary Drinking Water
Regulations: Radionuclides. Final Rule. 40 CFR Parts 9, 141, and 142.
FR 2000b—Federal Register. Vol. 65, no. 78, April 21, 2000. Subpart B. Proposed Rules. 40 CFR Part
192.
FR 1989—Federal Register. Vol. 54, no. 240, December 15, 1989. National Emission Standards for
Hazardous Air Pollutants; Radionuclides; Final Rule and Notice of Reconsideration. 40 CFR Part 61.
6-4

-------
Graves 1974—Graves, D. Open Pit Mining. Mining Engineering, Vol.26., no. 8:23-25, 1974. Littleton,
CO: August, 1974.
Grey 1993—Grey, C. Uranium: From Ore to Concrete. The Nuclear Engineer, 34 (1993), no. 1, 1993.
Guilbert and Park 1996—Guilbert, J., and Park, C., Jr. The Geology of Ore Deposits. 5th edition.New
York, NY: W. H. Freeman, 1996.
Guimond 1975—Guimond, R., and Windham, S. Radioactivity Distribution in Phosphate Products, By-
products, Effluents, and Wastes. Technical Note ORP/CSD-75-3. Washington, DC: U.S. Environmental
Protection Agency, August 1975.
HE 1989—Hydro-Engineering. Design Investigations, Veca AML Program 16D. Administrative Report.
Cheyenne, WY: Wyoming Department of Environmental Quality, Land Quality Division, 1989.
HE 1987—Hydro-Engineering. Pumpkin Buttes Reconnaissance. Administrative Report. Cheyenne, WY:
Wyoming Department of Environmental Quality, Land Quality Division, 1987.
Hull and Burnett 1996—Hull, C., and Burnett, W. Radiochemistry of Florida Phosphogypsum. Journal of
Environmental Radioactivity 32 (1996) no. 3:213-38.
IAEA 2003—International Atomic Energy Agency. Technical Report Series No. 419. Extent of
Environmental Contamination by Naturally Occurring Radioactive Material (NORM) and Technological
Options for Mitigation. Vienna, Austria.
IAEA 1990—International Atomic Energy Agency. The Environmental Behavior of Radium, Volumes 1
and 2. Vienna, Austria: 1990.
ISCORS 2005—Interagency Steering Committee on Radiation Standards, Sewage Sludge and Ash
Subcommittee, ISCORS Assessment of Radioactivity in Sewage Sludge—Recommendations on
Management of Radioactivity in Sewage Sludge and Ash at Publicly Owned Treatment Works. ISCORS
Technical Report 2004-04, DOE/EH-0668, EPA 832-R-03-002B. Washington DC: ISCORS, February,
2005.
Jasinski 2003—Jasinski, S. "Phosphate Rock". In Minerals Year Book-2002. Reston, VA: U.S.
Geological Survey, 2003.
Kennecott Uranium Company 2004—Kennecot Uranium Company. Written communication to U.S. EPA,
Office of Radiation and Indoor Air. Rawlins, Wyoming: December 2, 2004.
Kittel 1963—Kittel, D. "Geology of the Jackpile Mine Area." In Geology and Technology of the Grants
Uranium Region, comp. V.C. Kelley. Memoir 15. Socorro, NM: New Mexico Bureau of Mines and
Mineral Resources, 1963.
LAI 1996—Lidstone and Anderson, Inc, Inventory and Planning Work for the Remaining Eligible Sites,
Gas Hills Uranium District, Wyoming. AML 16: Administrative Report. Cheyenne, WY: Wyoming
Department of Environmental Quality, Land Quality Division, 1996.
6-5

-------
Leshendok 2004—Leshendok, T., Personal communication to U.S. EPA, Office of Radiation and Indoor
Air. Spark, NV: October 14, 2004.
Longsworth 1994—Longsworth, S. Geohydrology and Water Chemistry of Abandoned Uranium Mines
and Radiochemistry of Spoil-Material Leachate, Monument Valley and Cameron Areas, Arizona and
Utah. USGS Investigations Report 93-4226. Washington, DC: U.S. Geological Survey, 1994.
Marcus 1997—Marcus, J., ed., Mining Environmental Handbook: Effects of Mining on the Environment
and American Environmental Controls on Mining. London, England: Imperial College Press, 1997.
McCarthy and Degueldre 1993—McCarthy, J., and Degueldgre. Sampling and Characterization of
Colloids and Particles in Groundwater for Studying Their Role in Contaminant Transport. In
Environmental Particles. Buffle, J., and van Leeuwen, P. (eds.), pp. 247-315. Boca Raton, Florida: Lewis
Publishers, 1993.
McFaul et al. 2000—McFaul, E., Mason, G. Jr., Ferguson, W., and Lipin, B. U.S. Geological Survey
Mineral Databases—MRDS and MAS/MILS. U.S. Geological Survey Digital Data Series DDS--52 Two
Disks. Reston, VA: U.S. Geological Survey, 2000.
McGinleyl980—McGinley, F., Potential By-product Uranium Production in the United States of
America. In Uranium Evaluation and Mining Techniques. IAEA document SM-239/15, pp. 293-397.
Vienna, Austria: International Atomic Energy Agency, 1980.
McLemore 1983—McLemore, V. Uranium and Thorium Occurrences in New Mexico: Distribution,
Geology, Production, and Resources, with Selected Bibliography. 3 vols. Open-File Report OF-183.
Albuquerque, NM: New Mexico Bureau of Mines and Mineral Resources, 1983.
Merrit 1971—Merrit, K..The Extractive Metallurgy of Uranium. Golden, CO: Colorado School of Mines,
1971.
Mertie 1953—Mertie, J., Jr. Monazite Deposits of the Southeastern Atlantic States. USGS Circular 237.
Washington, DC: U.S. Geological Survey, 1953.
Meshik 2005—Meshik, A., The Workings of an Ancient Nuclear Reactor. New York, NY: Scientific
American, November, 2005.
MFG 2005—MFG Inc. Final Completion Report for Removal of Ore Debris Along the Ford Wellpinit
Haul Road, March 2005, Prepared for Dawn Mining Company. MFG Project No. 180884/15. Fort
Collins, CO: March, 2005.
Moore et al. 1996—Moore, B., Price, J., and, Gardner, T. Reactivity in the South Spoils and Hillside
Dump at the Midnite Mine. U.S. Bureau of Mines Report of Investigations 9609. Reston, VA: U.S.
Geological Survey, 1996
Myrick et al 1981—Myrick, T., Berven, B., and Haywood, F. State Background Radiation Levels:
Results of Measurements Taken During 1975-1979. ORNL/TM-7343. Oak Ridge, TN: Oak Ridge
National Laboratory, 1981.
6-6

-------
NAS 1999a—National Academy of Sciences. Evaluation of Guidelines for Exposures to Technologically
Enhanced Naturally Occurring Radioactive Materials. Washington, DC: National Academy Press, 1999.
NAS 1999b—National Academy of Sciences. Health Effects of Exposure to Radon: BEIR VI.
Washington, DC: National Academy Press, 1999.
Navajo AMLR 2000—Navajo Abandoned Mine Land Reclamation Program, Carrizo #1AML
Reclamation Project, Nomination for the 2000 Abandoned Mine Land Reclamation Awards. Submission
to the Office of Surface Mining Reclamation and Enforcement. Window Rock, AZ: Navajo AMLRP,
2000.
NCRP 1993—National Council on Radiation Protection and Measurements. Radiation Protection in the
Mineral Extraction Industry. NCRP Report No. 118. Washington, DC: NCRP, August 1, 1993.
NCRP 1987a—National Council on Radiation Protection and Measurements. Radiation Exposure of the
U.S. Population from Consumer Products and Miscellaneous Sources. NCRP Report No. 95.
Washington, DC: NCRP, December 30, 1987.
NCRP 1987b—National Council on Radiation Protection and Measurements. Exposure of the Population
in the United States and Canada from Natural Background Radiation. NCRP Report No. 94.
Washington, DC: NCRP, December 1987.
NCRP 1984—National Council on Radiation Protection and Measurements. Exposures from the Uranium
Series with Emphasis on Radon and Its Daughters. NCRP Report No. 77. Washington, DC: NCRP,
March 15, 1984.
NEA/IAEA/OECD 2002—Nuclear Energy Agency, International Atomic Energy Agency, and
Organization for Economic Cooperation and Development. Environmental Remediation of Uranium
Production Facilities. Paris, France, and Vienna, Austria: 2002.
Oakley 1972—Oakley, D. Natural Radiation Exposure in the United States. U.S. EPA Report ORP/SID-
72-1. Washington, DC: U.S. Environmental Protection Agency, 1972.
Onishi et al. 1981—Onishi, Y., Serne, R., Arnold, E., Cowan, C., and Thompson, F. Critical
Review'.Radionuclide Transport, Sediment Transport, and Water Quality Mathematical Modeling; and
Radionuclide Adsorption/Desorption Mechanisms. NUREG/CR-1322 (PNL-2901), prepared for the U. S.
Nuclear Regulatory Commission, Washington, DC. Richland Washington: Pacific Northwest Laboratory,
1981.
Otton 1998—Otton, J. Written communication to U.S. EPA, Office of Radiation and Indoor Air.
USGS/EPA Interagency Agreement, 1998.
Panacea 2002—U.S. Army Corps of Engineers. Hydrogeologic Investigation Report for Yazzie 312 Mine,
Cameron Area, Arizona. Produced by Panacea, Inc., under Project No. C00-236. Los Angeles, CA:
US ACE, October 2002.
6-7

-------
Paulson 2004—Paulson, O. Status Update on the Biore mediation of the Sweetwater Pit Lake—Four
Years Following Treatment. Pit Lakes 2004. Reno, NV: November 16-18, 2004.
Pellike 1973—Pehlke, R.D. Unit Processes of Extractive Metallurgy. Elsevier North. New York, NY:
1973.
RCT 1994—Railroad Commission of Texas. South Texas Uranium District Abandoned Mine and
Inventory. Austin, TX: RCT, Surface Mining and Reclamation Division, 1994.
Rhodes 1987—Rhodes, R. The Making of the Atomic Bomb. New York, NY: Simon and Schuster, 1987.
Robson and Banta 1995—Robson, S., and Banta, E. Ground Water Atlas of the United States: Arizona,
Colorado, New Mexico, Utah. HA 730-C. Washington, DC: U.S. Geological Survey, 1995.
Rogowski 1978—Rogowski, A. Water Regime in Strip Mine Spoil. In Surface Mining and Fish/Wildlife
Needs in Eastern United States. Ed. D.E. Samuel, J.R. Stauffer, and W.T. Mason. FWS/OBS-78-81, 137.
Washington, DC: U.S. Fish and Wildlife Service, 1978.
SC&A 1993—S. Cohen and Associates, Inc. Diffuse NORM Wastes: Waste Characterization and
Preliminary Risk Assessment. Prepared for the U.S. Environmental Protection Agency under contract No.
68D20155. Washington, DC: U.S. EPA, May 1993.
SC&A 1989—S. Cohen and Associates, Inc. Radiological Monitoring at Inactive Surface Mines.
Prepared for the U.S. Environmental Protection Agency. Washington, DC: U.S. EPA, February 1989.
Shapiro 1990—Shapiro, J. Radiation Protection: A Guide for Scientists and Physicians. 3d ed.
Cambridge, MA: Harvard University Press, 1990.
Sheridan et al. 1962—Sheridan, D., Maxwell, C., and Collier, J. Geology of the Lost Creek
Schroeckingerite deposits, Sweetwater County, Wyoming. U.S. Geological Survey Bulletin 1087-J,
prepared for the U.S. Atomic Energy Commission. Washington, DC: U.S. Government Printing Office,
1961.
Skousen et al. 1988—Skousen, J., Rose, A., Geidel, G., Foreman, J., Evans, R., Hellier, W., and Members
of the Avoidance and Remediation Working Group of the Acid Drainage Technology Initiative,
Handbook of Technologies for Avoidance and Remediation of Acid Mine Drainage. Morgantown, WV:
National Mine Land Reclamation Center, West Virginia University, June 1, 1998.
SMI 1996—Shepard Miller, Inc. Comparison of the Relative Radiological Impacts of the Reclaimed Day
Loma Leached Material and the Gas Hills Uranium District. Prepared for Western Nuclear, Inc. Fort
Collins, CO: August 1996.
Smith 2002—Smith, L. Written communication with spreadsheet of U.S. Department of Energy/Energy
Information Administration uranium mines database. Washington, DC, 2002.
Sowder et al. 2001—Sowder, A., Hernandez, S., Bain, A., Setlow, L., and Forinash, B. Radiological
Survey of a Uranium-Contaminated Hogan in the Oljeto Chapter, San Juan County, UT, Prior to the
6-8

-------
April 2001 EPA Region IXRemoval Action on the Navajo Nation. Report summarized in the 2001 Health
Physics Society Annual Meeting poster presentation. Abandoned Uranium Mines: A Continuing Legacy
for the Navajo Nation. Washington, DC: U.S. Environmental Protection Agency, Office of Radiation and
Indoor Air, August 23, 2001.
Spatial Climate Analysis Service et al. 2000—Spatial Climate Analysis Service, Oregon State University;
and U.S. Department of Agriculture, Natural Resources Conservation Service, National Water and
Climate Center and National Cartography and Geospatial Center. United States Average Annual
Precipitation, 1961-1990. http://nationalatlas.gov/atlasftp.html. Corvallis, OR, Portland, OR and Fort
Worth, TX: September 2000.
SRB 1981—Scarborough, R. Radioactive Occurrences and Uranium Production in Arizona. U.S. DOE
Report GJBX-143 (81). Grand Junction, CO: U.S. Department of Energy, 1981.
Staatz et al. 1980—Staatz, M., Hall, R., Macke, D., Armbrustmacher, T., and Brownfield, I. Thorium
Resources of Selected Regions in the United States. USGS Circular 824. Washington, DC: U.S.
Department of the Interior, U.S. Geological Survey, 1980.
Tachi et al. 2001—Tachi, Y., Shibutani, T., Sato, H., and Yui, M. Experimental and Modeling Studies on
Sorption and Diffusion of Radium in Bentonite. Journal of Contaminant Hydrology 47 (2001): 171-86
Telluride Watch 2005—Telluride Watch, Colorado: Mines Reopen As Uranium Prices Increase.
Telluride. CO: January 7, 2005.
http://www.telluridewatch.com/archive news/2005/ianuarv/010605/uranium.htm
TV A 1978—Tennessee Valley Authority and U.S. Department of the Interior. Draft Environmental
Statement - Crownpoint Uranium Mining Project. Knoxville, TN: TVA, 1978.
UNSCEAR 1982—United Nations Scientific Committee on the Effects of Atomic Radiation. Ionizing
Radiation: Sources and Biological Effects. New York, NY: United Nations, 1982.
UNSCEAR 1972—United Nations Scientific Committee on the Effects of Atomic Radiation. Ionizing
Radiation: Levels and Effects. New York, NY: United Nations, 1972
URS 2002—URS Corporation. Midnite Mine Geotechnical Investigations and Existing Waste Rock Piles
and Open Pit Highwalls Stability Evaluations. Technical memorandum. Prepared for U.S. Environmental
Protection Agency. Denver CO: U.S. EPA, May 2002.
U.S. BLM 1998—U.S. Bureau of Land Management. Final Report-Removal Preliminary Assessment,
Bokan Mountain Mine, Craig Ranger District, Tongass National Forest, Region 10-Alaska. Juneau, AK:
BLM, September 1998.
U.S. BLM 1986—U.S. Bureau of Land Management. Jackpile-Paguate Uranium Mine Reclamation
Project, Laguna Indian Reservation, Cibola County, New Mexico: Final Environmental Impact
Statement. Vols. I and II. Albuquerque, NM: BLM, New Mexico State Office, Rio Puerco Resource Area,
1986.
6-9

-------
U.S. DOE 2005—U.S. Department of Energy. Final Environmental Impact Statement for
Remediation of the Moab Uranium Mill Tailings, Grand and San Juan Counties, Utah. DOE/EIS-0355.
Grand Junction CO: U.S. DOE, July 2005.
U.S. DOE 2002—U.S. Department of Energy. Final Environmental Impact Statement for a Geologic
Repository for the Disposal of Spent Nuclear Fuel and High-level Radioactive Waste at Yucca Mountain,
Nye County, Nevada. Chapter 1. DOE/EIS-0250. Washington, DC: U.S. DOE, February 2002.
U.S. DOE 1979—U.S. Department of Energy. National Uranium Resource Evaluation—Interim Report.
Figure 3.2, data files. Grand Junction, CO: U.S. DOE, Grand Junction Project Office, June 1979.
U.S. DOE/EIA 2005a—U.S. Department of Energy, Energy Information Administration. Total
Production of Uranium Concentrate in the United States, 1996 - 3rd Quarter 2005,
http://www.eia.doe.gov/cneaf/nuclear/dupr/qupd.html, Washington, DC. U.S. DOE: August 2005.
U.S. DOE/EIA 2005b—U.S. Department of Energy, Energy Information Administration. Domestic
Uranium Production Report, 3rd Quarter 2005 Production. Washington, DC:
U.S. DOE: August 2005, http://www.eia.doe.gov/cneaf/nuclear/dupr/dupr.html.
U.S. DOE/EIA 2005c—U.S. Department of Energy, Energy Information Administration. U.S. Forward-
Cost Uranium Reserves by Mining Method, December 31, 2003. From DOE/EIA Form EIA-851Q
"Domestic Uranium Production Report", Washington, DC: U.S. DOE, 2005.
http://www.eia.doe.gov/cneaf/nuclear/page/reserves/uresmine.html,
U.S. DOE/EIA 2005d—U.S. Department of Energy, Energy Information Administration. Table 28. U.S.
Coal Consumption by End-Use Sector 7999-2005 http://www.eia.doe.gov/cneaf/coal/auarterlv
Washington, DC: U.S. DOE, September, 2005.
U.S. DOE/EIA 2004—U.S. Department of Energy, Energy Information Administration. Major U.S.
Uranium Reserves (map), http://vvvvvv.eia.doe.gov/cneaf/nuclear/page/reserves/usarea.html.
Washington, DC: U.S. DOE: June, 2004.
U.S. DOE/EIA 2003a—U.S. Department of Energy, Energy Information Administration. Uranium
Industry Annual: 2002. DOE/EIA-0478(2002). Washington, DC: U.S. DOE, May, 2003.
U.S. DOE/EIA 2003b—U.S. Department of Energy, Energy Information Administration. Domestic
Uranium Production Report. Form EIA-851. Posted February 2003 at
http://www.eia.doe.gov/cneaf/nuclear/dupr/qupd.html
U.S. DOE/EIA 2001—U.S. Department of Energy, Energy Information Administration. Uranium
Industry Annual: 2000. DOE/EIA-0478(00). Washington, DC: U.S. DOE, May 2001.
U.S. DOE/EIA 2000a—U.S. Department of Energy, Energy Information Administration. Uranium
Industry Annual: 1999. DOE/EIA-0478(99). Washington, DC: U.S. DOE, May 2000.
6-10

-------
U.S. DOE/EIA 2000b—U.S. Department of Energy, Energy Information Administration. Data
Compilation and Analysis of Costs Relating to Environmental Restoration of U.S. Uranium Production.
Washington, DC: U.S. DOE, March 2000.
U.S. DOE/EIA 1997—U.S. Department of Energy, Energy Information Administration. Integrated Data
Base Report 1996, Spent Nuclear Fuel and Radioactive Waste Inventories, Projections and
Characteristics, Revision 13—December 1997. Washington, DC: U.S. DOE, 1997.
U.S. DOE/EIA 1995—U.S. Department of Energy, Energy Information Administration.
Decommissioning of U.S. Uranium Production Facilities. DOE/EIA-0592. Washington, DC:U.S. DOE,
February, 1995.
U.S. DOE/EIA 1993—U.S. Department of Energy, Energy Information Administration. Uranium Industry
Annual: 1992. DOE/EIA-0478(92). Washington, DC: U.S. DOE, October 1993.
U.S. DOE/EIA 1992—U.S. Department of Energy, Energy Information Administration. Domestic
Uranium Mining and Milling Industry: 1991 Variability Assessment. DOE/EIA-O477(91). Washington,
DC: U.S. DOE, December 1992.
U.S. DOE/EIA 1991—U.S. Department of Energy, Energy Information Administration. Uranium
Industry Annual 1990. DOE/EIA-0478(90), Distribution Category UC-98. Washington, DC: U.S. DOE,
1991.
U.S. DOI 1980—U.S. Department of the Interior, Bureau of Indian Affairs. Uranium Development in the
San Juan Basin, a Report on Environmental Issues. Prepared by San Juan Basin Regional Uranium Study,
Office of Trust Responsibilities, US Bureau of Indian Affairs. Washington DC: BIA,1980.
U.S. EPA 2006a—U.S. Environmental Protection Agency. Technologically Enhanced Naturally
Occurring Radioactive Materials (TENORM) from Uranium Mining: Volume II: Investigation of
Potential Health, Geographic, and Environmental Issues of Abandoned Uranium Mines. Technical Report
EPA-402-R-05-008 (inpress). U.S. Environmental Protection Agency. Washington, DC: U.S. EPA,
2006.
U.S. EPA 2006b—U.S. Environmental Protection Agency. Uranium Location Database Compilation.
Technical Report EPA-402-R-05-009 (inpress). U.S. Environmental Protection Agency. Washington,
DC: U.S. EPA, 2006.
U.S. EPA 2005—U.S. Environmental Protection Agency. A Regulator's Guide to Management of
Radioactive Residuals From Drinking Water Treatment Technologies. EPA 816-R-05-004. Washington
DC: U.S. EPA, July 2005.
6-11

-------
U.S. EPA 2004a—U.S. Environmental Protection Agency. Preliminary Remediation Goal Table. San
Francisco: U.S. EPA , 2004. http://www.epa.gov/region09/waste/sflind/prg/files/04prgtable.pdf
U.S. EPA 2004b—U.S. Environmental Protection Agency. Understanding Variation in Partition
Coefficient, Kd, Values, Vol 3: Review of Geochemistry and Available Kd Values for Americium, Arsenic,
Curium, Iodine, Neptunium, Radium, and Technitium. EPA 402-R-04-002c. Washington, DC: U.S.
EPA, July, 2004.
U.S. EPA 2003a—U.S. Environmental Protection Agency. Ground-Water Indicator Map forMidnite
Mine.
http://vosemite.epa.gov/R10/CLEANUP.NSF/midnite/Technical+Documents!QpenDocument&ExpandSe
ction= 1 Posted 2003.
U.S. EPA 2003b—U.S. Environmental Protection Agency. Guidance—Potential for Radiation
Contamination Associated with Mineral and Resource Extraction Industries. Washington DC: U.S. EPA,
Office of Radiation and Indoor Air, April 15, 2003.
U.S. EPA 2002—U.S. Environmental Protection Agency. Uranium Mine Database: Arizona, California,
Colorado, Nevada, New Mexico, North Dakota, South Dakota, Texas, Utah, Washington, Wyoming.
Washington, DC: U.S. EPA, September 2002.
U.S. EPA 2001a—U.S. Environmental Protection Agency. White King/Lucky Lass Superfund Site Record
of Decision: Fremont National Forest, Lakeview, Oregon. Seattle, WA: U.S. EPA, Office of
Environmental Cleanup, September 2001.
U.S. EPA 2001b—U.S. Environmental Protection Agency. Superfund Public Information System CD.
Fourth Quarter, FY01. Washington, DC: U.S. EPA Office of Emergency and Remedial Response, 2001.
U.S. EPA 2001c—U.S. Environmental Protection Agency, Use of Uranium Drinking Water Standards
under 40 CFR 141 and 40 CFR 192 as Remediation Goals for Groundwater at CERCLA Sites. Directive
no. 9283.1-14. Washington, DC: November 6, 2001.
U.S. EPA 2001d—U.S. Environmental Protection Agency, Science Advisory Board, TENORM—
Evaluating Occurrence and Risks, an SAB Advisory; A Science Advisory Board Advisory on EPA's
Approach for Evaluating Occurrence and Risks of Technologically Enhanced Naturally Occurring
Radioactive Material (TENORM). EPA-SAB-RAC-ADV-01-001. Washington, DC: U.S. EPA, February,
2001.
U.S. EPA 2000a—U.S. Environmental Protection Agency. Soil Screening Guidance for Radionuclides.
EPA/540-R-00-007. Washington, DC: U.S. EPA, October, 2000.
U.S. EPA 2000b—U.S. Environmental Protection Agency. Report to Congress on EPA's Guidances on
Technologically Enhanced Naturally Occurring Radioactive Materials. Washington, DC: U.S. EPA, June,
2000.
6-12

-------
U.S. EPA 2000c—U.S. Environmental Protection Agency. Radionuclides Notice of Data Availability.
Technical Support Document. Washington, DC: U.S. EPA, Office of Ground Water and Drinking Water,
Office of Indoor Air and Radiation, and U.S. Geological Survey, March, 2000.
U.S. EPA 2000d—U.S. Environmental Protection Agency. Abandoned Mine Site Characterization and
Cleanup Handbook. EPA 910-B-00-001. Seattle, WA: U.S. EPA, August, 2000.
U.S. EPA 1999a—U.S. Environmental Protection Agency. Technologically Enhanced Naturally
Occurring Radioactive Materials in the Southwestern Copper Belt of Arizona. EPA 402-R-99-002.
Washington, DC: U.S. EPA, October, 1999.
U.S. EPA 1999b—U.S. Environmental Protection Agency. Understanding Variation in Partition
Coefficient, Kj. Values, Vol 1: The Kd Model,Methods of Measurement, and Appi cation of Chemical
Reaction Codes. EPA 402-R-99-004A. Washington, DC: U.S. EPA, August, 1999.
U.S. EPA 1999c—U.S. Environmental Protection Agency. Understanding Variation in Partition
Coefficient, Kd. Values, Vol 2: Review of Geochemistry and Available Kd Values for Cadmium, Cesium,
Chromium, Lead, Plutonium,Radon, Strontium, Thorium, Tritium (3H), and Uranium. EPA 402-R-99-
004B. Washington, DC: U.S. EPA, August, 1999.
U.S. EPA 1998—U.S. Environmental Protection Agency. Use of Soil Cleanup Criteria in 40 CFRPart
192 as Remediation Goals for CERCLA Sites. Directive no 9200.4-25. Washington, DC: U.S. EPA,
February 12, 1998. http://www.epa.gov/superfund/resources/soil/cleanup.htm
U.S. EPA 1997a—U.S. Environmental Protection Agency. U.S. EPA Introduction to Hard Rock Mining a
CD-ROM Application. EPA 530-C-97-005. Washington, DC: U.S. EPA, September, 1997.
U.S. EPA 1997b—U.S. Environmental Protection Agency. EPA's National HardrockMining
Framework. Washington, DC: EPA Office of Water, September, 1997.
U.S. EPA 1997c—U.S. Environmental Protection Agency. Establishment of Cleanup Levels for CERCLA
Sites with Radioactive Contamination. OSWERNo. 9200.4-18. Washington, DC: U.S. EPA, August,
1997.
U.S. EPA 1995a—U.S. Environmental Protection Agency. Extraction and Beneficiation of Ores and
Minerals: Uranium. Vol. 5. Technical Resource Document. EPA 530-R-94-032. Washington, DC: U.S.
EPA, Office of Solid Waste, January, 1995.
U.S. EPA 1995b—U.S. Environmental Protection Agency. Human Health and Environmental Damages
from Mining and Mineral Processing Wastes. Draft Background Information Document. Washington,
DC: U.S. EPA, Office of Solid Waste, 1995.
U.S. EPA 1994—U.S. Environmental Protection Agency, Science Advisory Board. An SAB
Report: Review of Diffuse NORM Draft Scoping Document. EPA-SAB-RAC-94-013. Washington, DC:
U.S. EPA, May, 1994.
6-13

-------
U.S. EPA 1993a—U.S. Environmental Protection Agency. External Exposure to Radionuclides. Federal
Guidance Report No. 12. EPA-402-R-93-081. Washington, DC: U.S. EPA, September, 1993.
U.S. EPA 1993b—U.S. Environmental Protection Agency. Uranium Industry Profile. File No. Uran.
PEI.ALL. Washington, DC: U.S. EPA, Office of Solid Waste, January 21, 1993.
U.S. EPA 1993c—U.S. Environmental Protection Agency. EPA Map of Radon Zones. EPA-402-R-93-
071. Washington, DC: U.S. EPA, 1993. http://www.epa.gov/iaa/radon/zonemap .html
U.S. EPA 1990—U.S. Environmental Protection Agency. Report to Congress on Special Wastes from
Mineral Processing. EPA/530-SW-90-070C. Washington, DC: U.S. EPA, Office of Solid Waste and
Emergency Response, Washington, DC, July, 1990.
U.S. EPA 1989a—U.S. Environmental Protection Agency. "Human Health Evaluation Manual". In Risk
Assessment Guidance for Superfund. Vol. 1. EPA/540/1-89/002. Washington, DC: U.S. EPA, December,
1989.
U.S. EPA 1989b—U.S. Environmental Protection Agency. Risk Assessments, Environmental Impact
Statement, NESHAPSfor Radionuclides. Vol. 2. Background Information Document. EPA/520/1-89-006-
1. Washington, DC: U.S. EPA, September, 1989.
U.S. EPA 1986—U.S. Environmental Protection Agency. Final Rule for Radon-222 Emissions from
Licensed Uranium Mill Tailings, Background Information Document. U.S. EPA, August, 1986.
U.S. EPA 1985—U.S. Environmental Protection Agency. Report to Congress on Wastes from the
Extraction and Beneficiation of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium
Mining, and Oil Shale. EPA 530/SW-85-003. Washington, DC: U.S. EPA, December, 1985.
U.S. EPA 1983a—U.S. Environmental Protection Agency. Report to Congress on the Potential Health
and Environmental Hazards of Uranium Mine Wastes. Vol. 1. EPA 520/1-83-007. Washington, DC: U.S.
EPA, June, 1983.
U.S. EPA 1983b—U.S. Environmental Protection Agency. Report to Congress on the Potential Health
and Environmental Hazards of Uranium Mine Wastes. Vol. 2. EPA 520/1-83-007. Washington, DC: U.S.
EPA, June, 1983.
U.S. EPA 1983c—U.S. Environmental Protection Agency. Report to Congress on the Potential Health
and Environmental Hazards of Uranium Mine Wastes. Vol. 3. EPA 520/1-83-007. Washington, DC: U.S.
EPA, June, 1983.
U.S. EPA 1983d—U.S. Environmental Protection Agency, Office of Radiation Programs. Final
Environmental Impact Statement for Standards for the Control of Byproduct Materials from Uranium Ore
Processing (40 CFR 192). Volumes I & II. U.S. Government Printing Office, Washington, DC:
September, 1983.
6-14

-------
U.S. EPA 1982—U.S. Environmental Protection Agency. Final Environmental Impact Statement for
Remedial Action Standards for Inactive Uranium Processing Sites. EPA 520/4-82-013-1. Washington,
DC: U.S. EPA, October, 1982.
U.S. EPA 1979—U.S. Environmental Protection Agency. Indoor Radiation Exposure Due to Radium-226
in Florida Phosphate Lands. EPA-520/4-78-013. Washington, DC: U.S. EPA, September, 1979.
U.S. EPA 1975—U.S. Environmental Protection Agency. Preliminary Findings: Radon Daughter Levels
in Structures Constructed on Reclaimed Florida Phosphate Land. Technical Note ORP/CSD-75-4.
Washington, DC: U.S. EPA, September, 1975.
U.S. EPA 1973—U.S. Environmental Protection Agency. Summary Report of Radiation Surveys
Performed in Selected Communities. Washington, DC: U.S. EPA, Office of Radiation Programs, 1973.
U.S. EPA and USACE 2000—U.S. Environmental Protection Agency and U.S. Army Corps of
Engineers. Abandoned Uranium Mines Project Arizona, New Mexico, Utah-Navajo Lands Project Atlas,
1994-2000. San Francisco and Los Angeles, CA: U.S. EPA and USACE, December, 2000.
U.S. EPA et al. 2001—U.S. Environmental Protection Agency, U.S. Nuclear Regulatory Commission,
U.S. Department of Energy, U.S. Department of Defense. Multi-Agency Radiation Survey and Site
Investigation Manual (MARSSIM) Revision 1. EPA 402-R-97-016, rev.l, NUREG-1575, rev. 1, DOE
/EH-0624, rev.l. Washington DC: U.S. EPA,U.S. NRC, U.S. DOE, August 2000, updated June, 2001.
htto: //www .epa. gov/radiation/marssim/obtain .htm
U.S. EPA et al. 2000—U.S. Environmental Protection Agency, U.S. Geological Survey, U.S. Bureau of
Land Management, U.S. Department of Energy. Field Demonstration of Permeable
Reactive Barriers to Remove Dissolved Uranium from Groundwater, Fry Canyon, Utah. EPA 402-C-00-
001. Washington, DC: November, 2000. http://www.epa.gov/radiation/docs/cleanup/402-c-0Q-
001.pdf
USFS 1991—U.S. Forest Service. Draft EIS RI/FS for the Cleanup & Rehabilitation of the White King
and Lucky Lass Uranium Mines, Fremont National Forest, Lakeview, Oregon. R6-FRE-001-91. Klamath
Falls, OR: U.S. USFS, August, 1991.
USGS 1993—U.S. Geological Survey. Terrestrial Gamma-Ray Exposure at lm Above Ground. Digital
Data Series DDS-9. Reston, VA: U.S Geological Survey, 1993.
USGS 1973—U.S. Geological Survey. United States Mineral Resources. Ed. D. Brobst and W. Pratt.
Professional Paper 820. Washington, DC: U.S. Geological Survey, 1973.
U.S. NPS 2006—U.S. National Park Service. Community Fact Sheet Orphan Mine Site, Grand Canyon
National Park-Revision 2. Grand Canyon, Arizona: February, 2006.
http://www.nps. gov/grca/publications/orphan 1 .pdf
U.S. NPS 2003—U.S. National Park Service. Community Fact Sheet Orphan Mine Site. National Park
Service, Grand Canyon National Park. Revision 1. Grand Canyon, Arizona: U.S. NPS, November, 2003.
6-15

-------
U.S. NPS 2000—U.S. National Park Service. Management Policies 2001. Washington DC: NPS,
December, 2000. http://www.nps.gov/policv/mp/policies/pdf
U.S. NRC 2004—U.S. Nuclear Regulatory Commission. Standard Review Plan for the Review of a
Reclamation Plan for Mill Tailings Sites Under Title II of the Uranium Mill Tailings Radiation Control
Act of1978. NUREG-1620. Washington, DC: U.S. NRC, July, 2004.
U.S. NRC 2003—U.S. Nuclear Regulatory Commission. Standard Review Plan for In Situ Leach
Uranium Extraction License Applications. NUREG-1569. Washington, DC: U.S. NRC, June, 2003.
U.S. NRC 2002—U.S. Nuclear Regulatory Commission. Design of Erosion Protection for Long-term
Stabilization. NUREG-1623, Washington, DC: U.S. NRC, September, 2002.
U.S. NRC 2001—U.S. Nuclear Regulatory Commission. Systematic Radiological Assessment of
Exemptions for Source and By-product Materials. NUREG-1717. Washington, DC: U.S. NRC, June,
2001.
U.S. NRC 2000a—U.S. Nuclear Regulatory Commission. NRC Regulatory Issue Summary 2000-23,
Recent Changes To Uranium Recovery Policy. Washington, DC: U.S. NRC, November, 2000.
U.S. NRC 2000b—U.S. Nuclear Regulatory Commission. NMSS Decommissioning Standard Review
Plan. NUREG-1727. Washington, DC: U.S. NRC, September, 2000.
U.S. NRC 1994—U.S. Nuclear Regulatory Commission. Background as a Residual Radioactivity
Criterion for Decommissioning, ed. A.M. Huffert, R.A. Meek, and K.M. Miller. Rep. NUREG-1501.
Washington, DC: U.S. NRC, 1994.
U.S. NRC 1980—U.S. Nuclear Regulatory Commission. Final Generic Environmental Impact Statement
on Uranium Milling. NUREG-0706. Washington, DC: U.S. NRC, September, 1980.
U.S. NRC and U.S. EPA 1997—U.S. Nuclear Regulatory Commission and U.S. Environmental
Protection Agency. Multi-Agency Radiation Survey and Site Investigation Manual (MARSSIM).
NUREG-1575 and EPA-402. Washington, DC: U.S. NRC, December, 1997.
Waite et al. 1992—Waite, T., Payne, J., Davis, J., and Sekine, K. Alligators Rivers Analogue Project,
Final Report, Volume 13, Uranium Sorption. ISBN 0-642-599394 (DOE/HMIP/RR/92/0823, SKI TR
92:20-13), 1992.
WDEQ 1991—Wyoming Department of Environmental Quality, Land Quality Division. In Situ Mining
State Decision Document for Everest Minerals Highland Uranium, WDEQ/LQD Permit No. 603-A2.
Cheyenne, WY: WDEQ, 1991.
Weston 1997—Roy F. Weston, Inc. Draft Final Remedial Investigation Report. Vol. 1. Oklahoma City,
OK: Kerr-McGee Corporation, August, 1997.
6-16

-------
Whitworth 1996—Whitworth, T.M,. Potential Environmental Impact of the Abandoned La Bajada
Uranium Mine Near Cochiti Lake, Santa Fe and Sandoval Counties, New Mexico. In New Mexico
Geology, August 1996, pp. 71-77.
Williams and Riley 1993—Williams, B., and J. Riley. Midnite Uranium Mine-Hydrologic Research and
Characterization. Presented May 16-19,1993, at the National Meeting of the American Society for
Surface Mining and Reclamation, in Spokane, Washington.
Wogman 1979—Wogman, N., Environmental Study of Active and Inactive Uranium Mines andMills and
their Effluents. PNL Laboratory Report 3069. Richland Washington: Battelle Pacific Northwest
Laboratories, 1979.
WRCC 2003—Western Regional Climate Center, Desert Research Institute. Average Pan Evaporation
Data by State, http://www.wrcc.dri.edu/htmlfiles/westevao.final.html.
Wyoming Mining Association 2004—Wyoming Mining Association. Written communication to U.S.
EPA, Office of Radiation and Indoor Air. Cheyenne, Wyoming: December 6, 2004.
Yu et al. 2001—Yu, C., Zielen, A., Cheng, J., LePoire, D., Gnanapragasam, E., Kamboj, S.
Arnish, J., Wallo III, A. Williams, W. and Peterson, H. User's Manual for RESRAD. Version 6.
Argonne, IL: Argonne National Laboratory, Environmental Assessment Division, July, 2001.
Yu et al. 1994—Yu, C., LePoire, D, Loureiro, C., Jones, L., and Chen, S. RESRAD-BUILD: A Computer
Model for Analyzing the Radiological Doses Resulting from the Remediation and Occupancy of Buildings
Contaminated with Radioactive Material. ANL/EAD/LD-3. Argonne, IL: Argonne National Laboratory,
Environmental Assessment Division, November, 1994.
6-17

-------
Appendix I. List of Acronyms and Abbreviations,
and Glossary of Terms
List of Acronyms and Abbreviations
Ac
actinium
ac
acre
ac-ft
acre-feet
ACAA
American Coal Ash Association
AEA
Atomic Energy Act
AEC
Atomic Energy Commission
ALARA
As low as reasonably achievable
AML
abandoned mine lands
As
arsenic
ATSDR
Agency for Toxic Substances and Disease Registry
Ba
barium
BASINS
Better Assessment Science Integrating Source and Non-point Sources (USGS

computer model)
BAT
best achievable technology
Bi
bismuth
BPCT
best practicable control technology
Bq/kg
Becquerel/kilogram.
BRC
Bureau of Radiation Control
CAA
Clean Air Act
CaS04
calcium sulphate (formula for gypsum)
CERCLA
Comprehensive Environmental Response, Compensation and Liability Act

(Superfund)
CFR
Code of Federal Regulations
Ci
Curie(s) (unit of radioactivity, 3.7 x 1010 disintegrations per second)
cm
centimeter
COD
chemical oxygen demand
Cr
chromium
CRCPD
Conference of Radiation Control Program Directors
Cu
copper
CWA
Clean Water Act
D&D
decontamination and decommissioning
DOE
Department of Energy
DOI
Department of the Interior
dscm
dry standard cubic meter
E
used to denote exponents (3.7E+10)
EIA
Energy Information Administration (U.S. Department of Energy)
EPA
Environmental Protection Agency
ESRI
Environmental Systems Research Institute
°F
degrees Fahrenheit
Fe
iron
FeCl3
ferric chloride
FeP
ferro-phosphorus
FeS2
pyrite
FIPR
Florida Institute of Phosphate Research
Fr
francium
AI-l

-------
ft	feet
g	gram
g/cm3	gram per cubic centimeter
Gy	Gray
H	hydrogen
ha	hectare, 2.471 acres
HDS	high-density sludge
Hg	mercury
hr	hour
ISL	in situ leaching
K	potassium
Kd	element-specific soil-water partition coefficient
kg	kilogram
L	liter
LTSP	long-term surveillance plan
(j,	micro, 10"6, used in combination with specific units
|ig/m	microgram per meter
(.ig/ni3	microgram per cubic meter
(j,m	one-millionth of a meter (micron)
(j,R/hr	microRoentgen per hour
m	milli, 10"3, used in combination with specific units
m	meter
m2	square meter
m2/s	square meters per second
m3	cubic meter
MAS/MILS Minerals Availability System/Minerals Industry Location System (USGS
database)
mbd	million barrels per day
MCL	maximum contaminant level
mg	milligram
mL	milliliter
Mn	manganese
Mo	molybdenum
MOU	memorandum of understanding
mrem	millirem
mR/hr	milliRoentgen per hour
mSv	milliSievert
MT	metric ton(s), 1000kg, or 2,200 lb
MMTs	millions of metric tons
n	nano, 10"9, used in combination with specific units
NAAQS	National Ambient Air Quality Standards
NAMLRP	Navajo Abandoned Mine Lands Reclamation Program
NARM	naturally occurring and accelerator-produced radioactive material
NAS	National Academy of Sciences
NCRP	National Council on Radiation Protection and Measurements
NEPA	National Environmental Policy Act
NESHAP	National Emission Standards for Hazardous Air Pollutants
NFS	National Forest Service
NNEPA	Navajo Nation Environmental Protection Agency
NORM	naturally occurring radioactive material
NPDES	National Pollutant Discharge Elimination System
AI-2

-------
NPL	National Priorities List
NPS	National Park Service
NRC	Nuclear Regulatory Commission
NSPS	New Source Performance Standards
02	oxygen
ORIA	Office of Radiation and Indoor Air (U.S. EPA)
OSM	Office of Surface Mining
p	pico, 10"12, used in combination with specific units
Pa	protactinium
Pb	lead
pCi/g	picocurie per gram
pCi/L	picocurie per liter
pCi/m2/s	picocurie per meter squared per second
pH	negative log of hydrogen ion concentration (measure of acidity and alkalinity)
Po	polonium
ppb	parts per billion, 10"9
ppm	parts per million, 10"6
Pu	plutonium
QA/QC	quality assurance/quality control
R	Roentgen
r2	correlation coefficient
Ra	radium
RCRA	Resource Conservation and Recovery Act
Rem	Roentgen equivalent in man
RESRAD	computer model to evaluate risks/doses from RESidual RADiation materials
(DOE's Argonne National Laboratory)
ROD	record of decision (Superfund)
s	second
SAB/RAC	Science Advisory Board/Radiation Advisory Committee (with U.S. EPA)
SARA	Superfund Amendments and Reauthorization Act
SDWA	Safe Drinking Water Act
Se	selenium
SEO	State Engineer's Office
SIP	State Implementation Plans
SMCRA	Surface Mining Control and Reclamation Act
Sr	strontium
SSL	soil screening level, in pCi/g
Sv	Sievert
tpd	tons per day
TDS	total dissolved solids
TENORM	technologically enhanced, naturally occurring radioactive material
Th	thorium
T1	thallium
TNRCC	Texas Natural Resources Conservation Commission (now Texas Commission on
Environmental Quality)
TRC	Texas Railroad Commission
TSD	treatment, storage, and disposal
TSS	total suspended solids
TWC	Texas Water Commission
U	uranium
U308	oxide of uranium
AI-3

-------
U4+T1206
brannerite
UIC
underground injection control
UMTRA
Uranium Mill Tailings Remedial Action program (U.S. DOE)
UMTRCA
Uranium Mill Tailings Radiation Control Act of 1978
UNSCEAR
United Nations Scientific Committee on the Effects of Atomic Radiation
uo2
uranium dioxide
U02S04
uranium sulfate
USiO4B«H20
coffinite
U.S. ACE
U.S. Army Corps of Engineers
USDA
U.S. Department of Agriculture
3
y
cubic yard(s)
Glossary of Terms
Adits	Horizontal or nearly horizontal passages driven from the surface for the
working or dewatering of a mine. If driven through a hill or mountain to
the surface on the other side it would be a tunnel.
ALARA
Alpha Particle
Aquifer
Background
Becquerel (Bq)
Acronym for As Low As Reasonably Achievable: A basic concept of
radiation protection which specifies that exposure to ionizing radiation
and releases of radioactive materials should be managed to reduce
collective doses as far below regulatory limits as is reasonably
achievable considering economic, technological, and societal factors,
among others.
A positively charged particle emitted by some radioactive materials
undergoing radioactive decay. A helium nucleus (two protons and
two neutrons)
An underground geological formation, or group of formations,
containing water. Sources of groundwater for wells and springs.
Radiation from cosmic sources, naturally occurring radioactive
material, including radon (except as a decay product of source or
special nuclear material), and global fallout as it exists in the
environment from the testing of nuclear explosive devices or from
nuclear accidents like Chernobyl which contribute to background
radiation and are not under the control of the cognizant organization.
The International System (SI) unit of activity equal to one nuclear
transformation (disintegration) per second. 1 Bq = 2.7xl0"n Curies (Ci)
= 27.03 picocuries (pCi).
Berm	A horizontal shelf or ledge built into the embankment or sloping wall of
an open pit, quarry, or ground surface to break the continuity of an
otherwise long slope and to strengthen its stability or to catch and arrest
slide material.
Beta Particle	An electron emitted from an atom's nucleus during radioactive decay.
AI-4

-------
Beneficiated	The initial attempt at liberating and concentrating a valuable mineral
from extracted ore. This is typically performed by employing various
crushing, grinding and froth flotation techniques. The remaining
(beneficiated) material is often physically and chemically similar to the
material (ore or mineral) that entered the operation, except that particle
size reduction has often occurred.
Bioremediation	The use of biological agents, such as bacteria or plants, to remove or
neutralize contaminants, as in polluted soil or water.
A radioactive uranium bearing mineral, (U,Ca,Y,Ce)(Ti,Fe)206
A coarse-grained clastic rock, composed of angular broken rock
fragments held together by a mineral cement or in a fine-grained matrix.
Breccia may originate as a result of talus accumulation, explosive
igneous processes, collapse of rock material, or faulting.
Brannerite
Breccia
Byproduct
Materials	Tailings or wastes produced by the extraction or concentration of
uranium or thorium from any ore processed primarily for its source
material content, including discrete surface wastes resulting from
uranium solution extraction processes. Underground ore bodies depleted
by such solution extraction operations do not constitute "byproduct
material" within this definition.
Carbonates
Cleanup
Coffinite
Consolidated
Contamination
A sediment or sedimentary rock formed by the organic or inorganic
precipitation from aqueous solution of carbonates of calcium,
magnesium, or iron; e.g., limestone and dolomite.
Actions taken to deal with a release or threatened release of hazardous
substances that could affect public health or the environment. The term
is often used broadly to describe various Superfund response actions or
phases of remedial responses, such as remedial investigation/feasibility
study. Cleanup is sometimes used interchangeably with the terms
remedial action, response action, or corrective action.
A naturally occurring uranium mineral, U(Si04)i_x(0H)4x
In geology, any or all of the processes whereby loose, soft, or liquid
earth materials become firm and coherent, either cemented or non-
cemented together.
The presence of residual radioactivity, heavy metals or other pollutants
in excess of levels which are acceptable for release of a site or facility
for unrestricted use.
Core Sample	A soil, rock, or sediment sample taken by core drilling.
Conventional Mining Mining which uses either mechanical open-pit surface mining methods,
or underground mining methods, or a combination of both, to extract ore
AI-5

-------
from the ground. This is opposed to unconventional or solution mining
methods.
Curie (Ci)
The customary unit of radioactivity. One curie (Ci) is equal to 37 billion
disintegrations per second (3.7 x 1010 dps = 3.7 x 101CI Bq), which is
approximately equal to the decay rate of one gram of Ra-226. Fractions
of a curie, e.g. picocuries (pCi) or 10"12 Ci and microcurie (jxCi) or 10"6
Ci, are levels typically encountered in radiation measurements of NORM
or TENORM.
Decline
Decommission
A downward ramp.
To remove a facility or site safely from service and reduce residual
radioactivity to a level that permits release of the property and
termination of a source materials license and other authorization for site
operation.
Decommissioning
The process of removing a facility or site from operation, followed by
decontamination, and license termination (or termination of authorization
for operation) if appropriate. The objective of decommissioning is to
reduce the residual radioactivity in structures, materials, soils,
groundwater, and other media at the site so that the concentration of each
radionuclide contaminant that contributes to residual radioactivity is
indistinguishable from the background radiation concentration for that
radionuclide.
Drill Cuttings
Drilling Wastes
Dose
Electrodialysis
Elution
Evaporative Ponds
The particles of rock produced in a borehole or drill hole by the abrasive
or percussive action of a drill bit; erosive effect of the circulating liquid;
or cavings from the borehole. At some mines and operations sites, cores
of rock from a well or borehole may be left behind as waste—referred to
in this report as drill cuttings for convenience.
Wastes associated with a drillhole operation at a mine or extraction
facility that are not considered cuttings or cores. May include drill muds
or other drilling fluids, sludges, or evaporation products collected in
excavated pits from waste water produced during drilling.
A general term used to refer to the effect on a material that is exposed to
radiation. It is used to refer either to the amount of energy absorbed by a
material exposed to radiation, or to the potential biological effect in
tissue exposed to radiation
A means of extracting one or more dissolved materials from a liquid
mixture, the process is dialysis assisted by the application of an electric
potential across a semi-permeable membrane.
Process of removing an economic mineral (uranium) from an ion
exchange filter or resin.
Areas where mine water or other produced water is placed and dried by
evaporation, leaving a residue of solids or sludges.
AI-6

-------
Evaporite
An inorganic chemical sediment that precipitates when the salty water in
which it had dissolved evaporates.
Excavated Wall
A wall of mineral ore that has been exposed by mining over a
considerable width at one time.
Exposure Pathway The route by which radioactivity travels through the environment to
eventually cause radiation exposure to a person or group (e.g., air or
water). Also, the route by which a member of the public is exposed (e.g.,
ingestion, inhalation).
External Radiation Radiation from a source outside the body.
Extraction Facility An industrial complex and land on which are located buildings, wells and
pipelines, mechanical and chemical equipment, storage and
transportation equipment licensed by the Nuclear Regulatory
Commission or its Agreement States for the purposes of extracting
uranium (source material) in accordance with the Atomic Energy Act.
Extraction Process A process used to extract uranium from ore, either by milling and
chemically treating the ore, or using chemical solutions to treat
underground ore {in situ leaching), or by treating mined and crushed ore
on the surface (heap leaching). These processes are licensed activities by
the Nuclear Regulatory Commission or its Agreement States in
accordance with the Atomic Energy Act.
Gamma Radiation Penetrating high-energy, short-wavelength electromagnetic radiation
(similar to X-rays) emitted during radioactive decay. Gamma rays are
very penetrating and require dense materials (such as lead or steel) for
shielding.
Gangue
Garnet
Half-Life (t1/2)
Heap-Leaching
The valueless minerals in an ore; that part of an ore that is not
economically desirable but cannot be avoided in mining. It is separated
from the ore minerals during concentration.
A group of silicate minerals found in igneous rocks, usually red in color,
used as a semi-precious stone in crystalline form, or ground into smaller
particles and used for abrasives such as in sandpaper coating.
The time required for one-half of the atoms of a particular radionuclide
present to disintegrate.
A method of extraction by which mineral bearing ores are leached on the
ground surface from weathered low-grade ore. The crushed material is
laid on a slightly sloping, impervious pad and uniformly leached by the
percolation of leach liquor trickling through the beds by gravity to ponds.
The metals are recovered by conventional methods from the solution.
AI-7

-------
Igneous
Rock or mineral that solidified from molten or partly molten material,
i.e., lava or magma. These rocks constitute one of the three main classes
into which all rocks are divided: igneous, metamorphic, and sedimentary.
Ilmenite
An iron-black, opaque mineral (FETi03) which is the principal ore of
titanium.
Incline	A slanting shaft from the surface into an underground mine. Most
commonly referring to an upward slope.
In Situ Leaching (ISL) A method of extraction by which mineral bearing ores are leached
underground by the introduction of a solvent solution, called a lixiviant,
through injection wells drilled into the ore body. The process does not
require the extraction of ore from the ground. The lixiviant is injected,
passes through the ore body, and mobilizes the mineral, and the mineral-
bearing solution is pumped to the surface from production wells. The
pregnant leach solution is processed to extract the mineral sought after.
Ion Exchange
A common water-softening method often found on a large scale at water
purification plants that remove some organics and radium by adding
calcium oxide or calcium hydroxide to increase the pH to a level where
the metals will precipitate out.
Lab Waste
Wastes of any kind generated by a laboratory, usually on-site, analyzing
rock, sediment, water or other samples obtained at the mine or extraction
facility, or its vicinity.
Leachate
A solution obtained by leaching; e.g., water that has percolated through
soil containing soluble substances and that contains certain amounts of
these substances in solution.
Leach Liquor
Leuxocene
Lithologic
Lixiviant which contains minerals dissolved from host rocks.
General term for a fine-grained, opaque, whitish alteration (weathering)
product of ilmenite in mineral form.
Character of a rock described in terms of its structure, color, mineral
composition, grain size, and arrangement of its component parts; all
those visible features that in the aggregate impart individuality to the
rock. Lithology is the basis of correlation in coal mines and commonly is
reliable over a distance of a few miles.
Longwall Retreat A method of mining flat-bedded deposits, in which the working face is
mined over a considerable width at one time. The excavation retreats
towards the shaft. In this method, all the roadways are in the ore body
and the waste areas are left behind.
Lixiviant	A liquid medium that selectively extracts the desired metal from the ore
or material to be leached rapidly and completely, and from which the
desired metal can then be recovered in a concentrated form.
AI-8

-------
Mill Tailings
Residue of raw material or waste separated out during the processing of
uranium mineral ores. Byproduct material in accordance with the AEA.
Mine
Mining is the mechanical process by which mineral ores are extracted
from the earth.
Mine Footprint
Mineral Sands
NORM
The areal extent of land physically disrupted by a mine operation.
Eroded and generally unconsolidated sedimentary particles of rock
minerals of sand size which have accumulated in a geologic deposit, and
may be exploited or concentrated for economic purposes.
Naturally Occurring Radioactive Materials. Materials which may contain
any of the primordial radionuclides or radioactive elements as they occur
in nature, such as radium, uranium, thorium, potassium, and their
radioactive decay products, that are undisturbed as a result of human
activities.
Ore
Overburden
Permeable Reactive
Barrier
Pillar
Pit Lake
The naturally occurring material from which a mineral or minerals of
economic value can be extracted profitably or to satisfy social or political
objectives. The term is generally but not always used to refer to
metalliferous material, and is often modified by the names of the
valuable constituent; e.g., iron ore; ore mineral.
Designates material of any nature, consolidated or unconsolidated, that
overlies a deposit of useful materials or ores, especially those deposits
that are mined from the surface by open cuts or open-pit methods.
An emplacement of reactive materials in the subsurface designed to
intercept a contaminant plume, provide a preferential flow path through
the reactive media, and transform the contaminant(s) into
environmentally acceptable forms to attain remediation concentration
goals at points of compliance.
A column of ore left to support the overlying strata or hanging wall in a
mine, generally resulting in a "room and pillar" array. Pillars are
normally left permanently to support the surface or to keep old workings
water tight.
A lake which has formed by accumulation of water in an open-pit mine
excavation.
Pit Lake Water
Protore
Water which has filled an open-pit mine excavation, usually derived as
water from underground workings of the mine.
Mineral bearing rock that cannot be further processed at a profit under
existing conditions but that may become profitable with technological
advances or price increases.
AI-9

-------
Pseudomorph	A mineral whose outward crystal form is that of, or which resembles
another mineral species: it has developed by alteration, substitution,
incrustation, or other mineral process.
Radiation Survey Measurements of radiation levels associated with a site together (or
Radiological	with appropriate documentation and data evaluation.
Survey)
Radioactivity	The mean number of nuclear transformations occurring in a given
quantity of radioactive material per unit time. The International
System (SI) unit of radioactivity is the Becquerel (Bq). The
customary unit is the Curie (Ci).
Radioactive Decay The spontaneous transformation of an unstable atom into one or more
different nuclides accompanied by either the emission of energy and/or
particles from the nucleus, nuclear capture or ejection of orbital
electrons, or fission. Unstable atoms decay into a more stable state,
eventually reaching a form that does not decay further or has a very
long half-life.
Radionuclide
Reclamation
Reductant
or Reduction
Regulation
Rem
An unstable nuclide that undergoes radioactive decay.
Restoration of mined land to original contour, use or condition.
The addition of hydrogen, removal of oxygen, or addition of electrons to
an element or compound.
A rule, law, order, or direction from federal, state, or Tribal governments
regulating action or conduct. Regulations concerning radionuclides in the
environment in the United States are shared by the Environmental
Protection Agency (EPA), the U.S. Nuclear Regulatory Commission
(NRC), the U.S. Department of Energy (DOE), state and Tribal
governments.
Radiation Equivalent in Man. The conventional unit of dose equivalent.
The corresponding International System (SI) unit is Sievert (Sv): 1 Sv =
100 rem.
Remediation	Cleanup or other methods used to remove or contain a toxic spill or
hazardous materials from a Superfund site, or uranium mine or extraction
facility, including those included under the Uranium Mill Tailings
Radiation Control Act (UMTRCA).
AI-10

-------
Refuse	Solid waste. Non-liquid, non-soluble materials ranging from municipal
garbage to industrial wastes that contain complex and sometimes
hazardous substances. Solid wastes also include sewage sludge,
agricultural refuse, demolition wastes, mining equipment and mining
residues. Technically, solid waste also refers to liquids and gases in
containers.
Removal
Rill
Risk Assessment
Room and Pillar
Rutile
Saturated Zone
Scanning
The cleanup or removal of released hazardous substances, or pollutants
or contaminants which may present an imminent and substantial danger;
such actions as may be necessary taken in the event of the threat of
release of hazardous substances into the environment; such actions as
may be necessary to monitor, assess, and evaluate the threat of release of
hazardous substances; the removal and disposal of material, or the taking
of other such actions as may be necessary to prevent, minimize or
mitigate damage to the public health or welfare or the environment.
A small channel, as one formed by erosion.
Qualitative and quantitative evaluation of the risk posed to human health
and/or the environment by the actual or potential presence and/or use of
specific pollutants.
A conventional method of underground mining in which natural pillars
are left unmined for support between the mined rooms.
A usually reddish-brown mineral (Ti02) that is an ore of titanium.
A subsurface zone of soil or rock in which all the pore spaces are filled
with water under pressure greater than that of the atmosphere. This zone
is separated from the zone of aeration (above) by the water table.
An evaluation technique performed by moving a detection device over
a surface at a specified speed and distance above the surface to detect
radiation.
Secular Equilibrium A state of parent-daughter equilibrium that is achieved when the half-
life of the parent radionuclide is much longer than the half-life of the
daughter radionuclide decay product. In this case, if the two are not
separated, the daughter will eventually decay at the same rate at which
it is being produced. At this point, both parent and daughter will decay
at the same rate until the parent is essentially exhausted.
Sievert (Sv)	The special name for the International System (SI) unit of dose
equivalent. 1 Sv = 100 rem = 1 Joule per kilogram.
Site	Any mine or extraction facility installation, or discrete, physically
separate parcel of land or lands disturbed by mining or uranium
extraction, or any building or structure or portion thereof.
Soils	All unconsolidated materials above bedrock.
AI-11

-------
Solution Process	A method of extracting sought-after underground elements or minerals
from in-place ore, or elements or minerals from ore previously mined
and crushed. This is accomplished through the use of fluids which
dissolve the mineral from the rock, putting it into liquid solution which is
then processed or evaporated to obtain the desired element or mineral.
Solvent Extraction A process for extracting a mineral or element (e.g., uranium) from ore by
soaking rock with a (solvent) that dissolves the target element from the
rock and putting it into liquid solution. The liquid is then processed or
evaporated to obtain the desired element.
Source Materials	Uranium or thorium, or any combination thereof, in any physical or
chemical form or (2) ores which contain by weight one-twentieth of one
percent (0.05%) or more of: (i) Uranium, (ii) thorium or (iii) any
combination thereof. Source material does not include special nuclear
material, chemical
Special Nuclear
Material
Plutonium, U-233, and Uranium enriched in U-235, material capable of
undergoing a fission reaction.
Stewardship
Institutional controls (private or publicownership or governmental)
which may be put in place to ensure that a specific site meets its closure
goals. Institutional controls can be either active, involving some form of
continuous or intermittent human activity to maintain the condition of the
site, or passive, which do not require human intervention and have an
amount of redundancy built into them to deter or prevent disturbance of
the closed site.
Stope	An excavation from which ore has been removed in a series of steps. A
variation of step. Usually applied to highly inclined or vertical veins or
beds.
Survey	A systematic evaluation and documentation of radiological
measurements with a correctly calibrated instrument or instruments that
meet the sensitivity required by the objective of the evaluation.
Survey Plan	A plan for determining the radiological and other characteristics of a site.
TENORM	Acronym for Technologically Enhanced Naturally Occurring
Radioactive Material. Naturally occurring radioactive materials that have
been concentrated or exposed to the accessible environment as a result of
human activities such as manufacturing, mineral extraction, or water
processing.
Underground Injection The method by which fluids are placed under pressure in a well such that
the fluid enters an underground rock formation. A means by which ISL
wells inject lixiviant to dissolve uranium from underground ore bodies.
Unconsolidated	Rocks consisting of loosely coherent or uncemented particles, whether
occurring at the surface or at depth.
AI-12

-------
Underflow
Flowing bottom waters containing dissolved or suspended solids.
Unsaturated zone
Uprate
Volcaniclastic
Waste Rock
Wastewater
Working Level
The zone in which the pore opening of the functional permeable rocks
are not (except temporarily) filled with water under hydrostatic pressure;
the interstices are either not filled with water or are filled with water that
is held by capillarity.
The process of increasing the maximum power level at which a
commercial nuclear power plant may operate.
A sedimentary rock containing volcanic material without regard to its
origin or environment of deposition.
Rock void of uranium ore which may have been set aside as waste after
removal of top-soil, overburden and uranium ore or veins. Waste rock is
defined as barren or submarginal rock or ore that has been mined, but is
not of sufficient value to warrant treatment and is therefore removed
ahead of the milling processes.
The spent or used water from a mine that contains dissolved or
suspended matter.
A special unit of radon exposure defined as any combination of short-
lived radon daughters in 1 liter of air that will result in the ultimate
5
emission of 1.3x10 MeV of potential alpha energy. This value is
approximately equal to the alpha energy released from the decay of
progeny in equilibrium with 100 pCi of Ra-222.
AI-13

-------
Appendix II. Uranium Decay Series
In the figures below, Figure AII.l. for the uranium-238 radioactive decay series, and Figure All.2. for the
uranium-23 radioactive decay series, each radioactive element is shown in a box with its mass number
(226Ra for example) along with its half life in (^seconds (|iscc). minutes (m), days (d), and years (y). The
principal type of radiation given off as the radionuclide decays is shown alongside the box: alpha (a),
beta ((3).
Figure AII.l. Uranium-238 Radioactive Decay Series
2§8 pjj
5.® d
r 4 Th
24 d
2,4 Pa
1.2 m
214
27 m
240.000 y
234
210
Th
218
3.1 m
214
20 m
AII-1

-------
Figure AII.2. Uranium-235 (Actinium) Decay Series
235 U
231 Pa
4.000 y
231 Th
227 Th
16
22 y
1.2%
223 Ra
12 d
223 Fr
21 m
219 Rn
3.9
CL
215 Po
211 Po
1.8 ms
0.52 S
211 Bi
a
2.2 m
211 Ft p
36 m
207 Pb
STABLE
207 Tl
4.8 m
AII-2

-------
Appendix III. Overview of Uranium Mines
and In Situ Leach Operations Case Studies
In the main body of this report, mention is made of a number of conventional uranium mines and ISL
leach operations which were studied in detail by EPA in order to better understand the environmental
conditions associated uranium extraction. Portions, though not all, of the data collected in the course of
those studies were included in the report in order to illustrate points made in the text. The conventional
mine sites listed in this appendix are abandoned, idle, or in reclamation status, and the descriptions which
follow provide information on their location, size, and production status. ISL sites described were
licensed facilities under the environmental oversight of and regulation of the NRC or its Agreement
States. The wastes from those facilities are considered byproduct materials and not TENORM. As such,
the information presented in this Appendix is for information purposes only. For a description of how
new ISL operations are carried out, see Chapter 2.
A decision will be made in the near future about whether or not more detailed information on the
conventional mine and ISL sites which was assembled as case studies for this report will be issued
separately.
Canyonlands Uranium Mines. Lathrop Canyon. Utah
This is a group of 12 abandoned mines in sandstone deposits of southeastern Utah in a semi-arid region of
the country. The mines are remotely located in Lathrop Canyon of the Canyonlands National Park near
Moab, Utah, about 1V2 hour hike from the nearest visitor's center at the park. Mine waste rock is found in
piles inside and outside the mines, with contaminated water located below the mines. Contaminated water
does not directly feed into any major bodies of water. Total waste amounts are estimated at 1,750 m3
(2,322 yd3). A study done by Burghardt et al. (2000) provides most of the data on the site contamination.
Data are available on metals concentrations, pH, radiation levels, and electrical conductivity for the waste
rock piles. Similar information is available for the Lathrop Canyon water and drainage. Based on this
information, as well as population proximity information, the National Park Service and Utah Abandoned
Mine Lands Reclamation Program maintain that Lathrop Canyon Mines now pose minimal risk to human
safety and health.
Orphan Uranium Mine. Arizona
The Orphan Uranium mine is located at the Grand Canyon National Park in northern Arizona and is being
assessed by the National Park Service for cleanup under CERCLA. The deposit is in sandstone and
claystone, but occurs as a breccia pipe deposit. The mine's buildings, hoisting headframe, and ore loadout
area are located a short walk from the south rim visitor's center, although the area has been fenced to deter
visitors. Mining activities were conducted mainly between 1956 and 1969 for uranium, copper, silver, and
vanadium. Radioactive rock and soil have been found at the loading area, and at the mine itself, which is
located below the canyon rim. The mine still contains significant amounts of unmined uranium. Horn
Creek, which lies beneath the Orphan Mine and along a major hiking trail of the park was found to
discharge "hostile" effluent containing uranium and exceeding the maximum contaminant level for gross
alpha radiation in drinking water. Uranium contamination of Horn Creek may be derived from: surface
runoff from the upper mine site and tailing debris at the lower mine site; groundwater and surface water
AIII-1

-------
that have percolated through the Orphan Mine, including the open glory hole; and ore and waste rock
debris containing uranium that has eroded and has been swept into the drainage basin of Horn Creek. The
case study includes results of Horn Spring sampling for uranium, as well as radiation levels recorded for
the upper and lower mine sites. Approximately two million people visit the vicinity of the mine annually;
however, relatively few individuals are directly exposed to radiation.
Further evaluation of the site in accordance with CERCLA is underway to evaluate the extent of
contamination and cleanup alternatives. According to the National Park Service (U.S. NPS 2006), an
Engineering Evaluation/Cost Analysis (EE/CA) should commence for the upper mine area in 2006. This
study would analyze cleanup action and the effectiveness, feasibility, and cost of a number of cleanup
alternatives. Upon completion, the EE/CA (including any recommended cleanup) and supporting
documents would be made available to the public for review and comment. An EE/CA for the lower and
middle mine areas was also being planned.
Midnite Uranium Mine. Washington
The Midnite Mine is an inactive open-pit uranium mine located within the boundaries of the Spokane
Indian Reservation in eastern Washington State, and is a disseminated deposit in igneous rocks. It was
operated by Dawn Mining Company between 1955 and 1981, and the disturbed area covers
approximately 320 acres (129.6 hectares). The initial series of open-pits were backfilled with waste rock
as mining progressed, and additional overburden and waste rock is on the surface, as well as a number of
ore/protore stockpiles. Two large pits remain open and accumulate water from multiple sources, including
seep water collected at the base of the largest waste rock pile. The pile was graded and partly reclaimed
by the mining company, which also operates an ongoing seep collection system and BaCl2 treatment
facility. Midnite Mine was listed as a Superfund site in 2000, and an EPA-funded study is under way. In
addition to the seeps and impounded surface water contaminated with heavy metals and radionuclides,
contamination has spread to areas outside the mined area in surface water and sediments, groundwater,
and road dust. Most runoff from the mined area flows to three streams (called "drainages"). The drainages
meet south of the mine and flow into Blue Creek. Blue Creek travels an additional 3.5 miles to the
Spokane River Arm of Lake Roosevelt. Shallow groundwater also flows from the mined area along the
three drainages and emerges south of the mined area. Collection and treatment of contaminated water has
reduced the amount of contamination entering surface water. However, the drainages and Blue Creek still
show ongoing contamination from the mine. A proposed cleanup plan was issued by EPA in September
of2005.
Bluewater Uranium Mines. New Mexico
The Bluewater Uranium mines are a series of three sandstone mine sites located in north Central Cibola
County in west-central New Mexico. Portions of the site had a semi-agricultural rural setting where
approximately 65 persons lived in 1990. The mines were operated primarily between 1952 and 1966.
Reclamation activities were conducted by EPA, ATSDR, and the Navajo Superfund Program to reduce
potential radiological hazards associated with the mines. As a result of previous mining activities and the
absence of reclamation action, the sites contained large open-pits with exposed uranium-bearing
overburden, waste rock, and protore. A contaminated water well and houses constructed with uranium
mine wastes were closed and removed. Radiological contaminants of concern were uranium and its
AIII-2

-------
daughter products of radium, thorium, bismuth, lead, and radon gas. Heavy metal species suspected to be
present in the mining waste were arsenic, barium, manganese, molybdenum, selenium, strontium, and
vanadium, Analytical data on uranium and radium were collected prior to and after the completion of
reclamation activities.
White King/Lucky Lass Uranium Mine Sites. Oregon
Also known as the Fremont National Forest Superfund Site, the site is located in south-central Oregon,
and includes two former uranium mining areas encompassing about 140 acres (about 57 hectares). The
site is located in a mountainous semi-arid setting on National Forest Service lands, with the closest
residences and drinking water wells more than 10 miles (16 kilometers) from the site. The mines are
located within the northwest terminus of the Basin and Range province. This area is characterized by
north-trending fault-block mountains and basins of internal drainage. Geologic units in the region are
characterized by a thick sequence of volcanic flows and volcaniclastic rocks which have been extensively
faulted and fractured. The major features include a water-filled excavation pit (pond); a protore stockpile;
an overburden stockpile; areas where overburden and ore were dumped or spilled; and Augur Creek,
which flows adjacent to the two White King stockpiles. Mining operations were conducted between 1955
and 1965, with exploratory drilling conducted until 1979. The area has been extensively sampled for
arsenic, uranium-234/238, radium, and radon. A baseline risk assessment was conducted and serves as
part of the record of decision (ROD). Construction for remediation of the sites began in 2005.
Yazzie—312 Mine. Cameron. Arizona
The Yazzie-312 Uranium Mine is located on the Navajo Indian Reservation located in the Painted Desert
section of the Black Mesa basin area near Cameron, Arizona. The site was operated between 1956 and
1961 and contained a large, water-filled open-pit lake; the water had been used for recreational swimming
and livestock watering. The water standing in the Yazzie-312 pit was the result of an artesian flow from
an underlying aquifer. The mine was in the Petrified Forest Member of the Chinle Formation. The mine
operator drilled a hole in the bottom of the pit looking for a deeper ore horizon. The drill hole
encountered artesian water in the Shinarump Member, which filled the pit.
The EPA studied the mine to determine: the presence of metals and radionuclides in water within the
mine pit, in underlying water, and in the Little Colorado River; assessing metals and radionuclides in
subsurface soil and sediments; determining infiltration in the water-filled mine pit; and assessing
communication into other aquifers at the site. Analytical data were collected on several borings for soil
samples, as well as several water samples. The area has several hard impermeable substrates located
between 50 and 130 feet (15.2 and 39.6 meters) below ground surface. Elevated levels of uranium and
thorium were found at soil depths that were above the groundwater table (110 to 210 feet) (33.5 to 64
meters-below ground surface), with significantly lower levels found at deeper depths. No metal levels
exceeded EPA Region 9's Preliminary Remediation Goals. In the overburden and protore piles, the most
significant contaminants were the uranium and thorium concentrations. Groundwater samples indicated
contamination for uranium, radium, arsenic, beryllium, chromium, and manganese. Pit water tested
similarly high for the same contaminants and for iron and lead. Testing also indicated that the Little
Colorado River contained measureable uranium, arsenic, beryllium, and chromium, although not at
significant levels. The mine site was remediated by the Navajo Abandoned Mine Land agency in 2002.
AIII-3

-------
Uranium In Situ Fields
Crow Butte. Nebraska
Cameco's facility and associated wellfields are located in west-central Dawes County, Nebraska, just
north of the Pine Ridge, five miles southeast of Crawford, Nebraska. The total surface area of the project
site is approximately 2,800 acres (1,134 hectares), with about 500 acres (202 hectares) that will be
disturbed during the life of the project. The uranium deposit at the Crow Butte site is a roll-front deposit,
similar to those in the Wyoming basins. Liquid wastes from operations are generated from three sources:
(1) wellfield development, (2) processing plant operations, and (3) aquifer restoration activities.
Currently, Cameco has three options approved by the NRC for the disposal of liquid wastes: (1) solar
evaporation ponds, (2) land application, or (3) deep-well injection. At this time, land application has not
been used. The study contains results for lead, polonium, radium, radon, thorium, and uranium, taken
from both the ponds located at the site and surface waters.
Holidav/El Mesauite. Texas
The Combined Holiday and El Mesquite ISL fields are located in Duval and Webb counties, Texas, and
they cover a permit area of approximately 4,500 acres (1,822 hectares). They are owned by COGEMA
which cited its total wellfield area as 335 acres (135 hectares) in two combined leases, with 1,750
injection wells and 1,450 production wells. Production commenced in 1977, with the expectation of 17
years of production and the fields' producing an ore grade of 0.07% using a sodium bicarbonate-injected
lixiviant. Production from the fields averaged 750 tons of uranium per year, with an estimated extraction
efficiency of 93 to 95%. Wastewater was collected at two storage ponds at the El Mesquite project before
injection into deep disposal wells. The El Mesquite project lease area comprises 2,900 acres (1174
hectares) including five wellfields, three satellite locations, a processing plant, a yellowcake dryer,
administrative buildings, a laboratory, a warehouse, and a maintenance shop. The Holiday lease covers
1,483 acres (600 hectares), including 10 wellfields and two satellite locations. Uranium production at the
Holiday and El Mesquite project areas has ceased, and negative pressure in producing wells of the field is
maintained to prevent excursions of pollutants (or plume migration) beyond mine lease boundaries. Areas
that were depleted at an early point in the operations history were subjects of groundwater restoration
activities. At Holiday and El Mesquite, the groundwater prior to extraction was usable for livestock
watering, (with some localized exceptions, due to elevated radium-226, which is present in the
groundwater within the uranium ore body). Therefore, COGEMA's goal after extraction is to clean up the
groundwater to as close to background conditions as possible.
AIII-4

-------
Irigaray and Christensen Ranch. Wyoming
The Irigaray and Christensen Ranch projects are two separate ISL operations that are located about 51 to
55 miles (82 to 88 kilometers) southeast of Buffalo in the Powder River Basin in northeast Wyoming. The
Irigaray property is 21,100 acres (8,545 hectares) and contains the central plant for both projects, though
the actual disturbed area for Irigaray is only 133 acres. COGEMA purchased both properties in April
1993, and all mining activities (at both sites) ceased in June 2000. The ore mineralization is one of many
roll-front type uranium deposits located in the Wasatch formation. Water treatment processes, such as
reverse osmosis, were used to clean wellfield bleed water for use in restoration. Uranium-laden resin from
the ion exchange columns was transferred to a tanker trailer and trucked to the Irigaray central plant for
elution, final uranium precipitation, and drying. Wastewater disposal capability included evaporation in
lined ponds, storage of clean water (reverse osmosis permeate) in clay-lined ponds, treatment and disposal
via surface discharge under a Wyoming National Pollutant Discharge Elimination System permit, and
deep-well injection. The lined solar evaporation ponds were initially designed to provide a surface area
and capacity capable of evaporating a 5 gallons per minute (about 19 liters per minute) process effluent
stream. The four lined solar evaporation ponds were designed to meet the requirements of the NRC.
Samples of the wastewater effluents were taken and tested for uranium and radium concentrations.
Restoration of the Irigaray well fields was complete in August 2002 and was expected to be complete at
Christensen Ranch in 2006. Surface decommissioning and reclamation are underway (as approved by
NRC) and should be complete in 2007.
Crownpoint Uranium. New Mexico
The proposed Crownpoint Uranium ISL project consists of three properties located near Church Rock,
New Mexico. Operations at the Crownpoint site would include a central processing facility where
yellowcake will be dried and packaged. Generally, the uranium deposits are a few feet thick and several
hundred to a thousand feet (305 meters) long, and may be stacked, usually parallel to the strike of the host
rock. Uranium was proposed to be extracted from the ore bodies by leachate mining, using a sodium
bicarbonate lixiviant, and is then extracted from the solution and concentrated. Uranium to be produced at
the Church Rock and Unit 1 sites, uranium concentrate, in the form of either uranium-loaded resin beads
or yellowcake slurry, would be shipped by truck to the central processing facility and packaged into a
final yellowcake product. Before the waste would be disposed of, barium chloride would be added to
effectively remove radium, thus lowering the radionuclide concentrations of the waste. HRI, the site's
owner and operator, is currently considering up to five different final disposal options for wastewaters
(both process-generated and restoration waters): (1) surface discharge, (2) land application, (3) brine
concentration, (4) waste-retention ponds, and (5) deep-well disposal. At present, HRI is limited to using
surface discharge (with appropriate state or federal permits/licenses), brine concentration, waste-retention
ponds, or a combination of the three options to dispose of process wastewater. In July 2005, NRC
required that HRI reduce its secondary groundwater restoration standard for uranium from 0.44 mg/L to
0.03 mg/L.
AIII-5

-------
Highlands Uranium. Wyoming
Operated by Power Resources, Inc., Highlands is a 15,000-acre (6,073 hectare) ISL facility, located in the
Southern Powder River Basin of east-central Wyoming, in central Converse County, Wyoming. The land
has been used for seasonal sheep and cattle grazing. The uranium production process uses a lixiviant
comprised of native groundwater with gaseous carbon dioxide and oxygen, which is injected into the ore
zone through a series of well patterns. Uranium becomes dissolved within the lixiviant, which is pumped
from the ground, treated to remove the uranium, then re-injected into the ore zone. Liquid wastes from the
operation consist of two types of wastewater: (1) freshwater streams and (2) a saltwater stream. The
freshwater streams consist of restoration wastewaters and well field/process purge. Together, the process
purge and restoration fluids make up the irrigation water source. Power Resources disposes of its
freshwater waste stream by using radium settling basins, purge storage reservoirs, and irrigation areas.
Due to erosion problems encountered with the original clay liner of the ponds, a geotextile fabric was
installed in September 1988 to protect against future erosion concerns. Data was obtained for radium and
uranium in the settling ponds. Saltwater waste is disposed of in a waste disposal injection well. The
saltwater waste is produced from several sources in the uranium recovery and yellowcake production
process. The sources that make up this waste stream include analytical laboratory liquid wastes, elution
agents decanted from the precipitation circuit, yellowcake wash water, reject solutions from the water
treatment process, and washdown water from the Central Processing Facility.
Smith Ranch. Wyoming
This Power Resources project acquired from Rio Algom, is a 16,000-acre (6,480 hectare) site at the Smith
Ranch, located in the North Platte River drainage in Converse County, approximately 17 miles (27.2
kilometers) northeast of Glenrock, Wyoming. Power Resources proposed to extract uranium at depths of
450 to 1,000 feet (137 to 305 meters). The project involves approximately 25 individual mining units.
When the project was to be fully operational, about two years after licensing, approximately five mining
units would be in production at a time. Extraction would proceed approximately three years in each unit,
followed by an equivalent period of unit restoration and surveillance monitoring. The proposed schedule
covers a total of about 20 years. Liquid effluents from the operation include the production bleed stream,
excess fluids from the elution and precipitation process, regeneration of the water softener system
(calcium control), yellowcake rinse water, plant washdown water, restoration equipment waste,
restoration bleed, and facility sanitary waste. If the water quality was acceptable, the water would then be
routed through a separate radium removal and solids settling system prior to evaporation and/or land
application (surface irrigation). Excess liquids from the elution and precipitation circuit and water
softener regeneration were expected to average about 60 gallons per minute (227 liters per minute) and
would be routed to lined evaporation ponds or to a disposal injection well. In 2005, Power Resources
applied for an amendment to the Smith Ranch/Highland license to include the adjacent planned Reynolds
Ranch ISL project as a satellite facility. Sample data on radium and uranium concentrations in
evaporation ponds from the pilot projects were obtained by EPA.
AIII-6

-------
Appendix IV. Calculations of Volumes of Uranium Overburden
and Waste Rock
Conventional mining techniques produce large amounts of solid waste materials. Open-pit mining in
particular produces large quantities of overburden, while underground mining produces lesser, but still
significant amounts of waste rock. Overburden and weakly mineralized waste rock that have not been
used for reclamation have usually been stored in piles on site and are usually unsaturated, given that most
conventional mining occurs in arid regions (U.S. DOE/EIA 1997). In general in this Appendix
overburden and waste rock have been included together in estimating total waste rock at the mine sites.
The density of mine wastes varies, depending on the type of ore body with which they are associated and
the geology of the enclosing rock formations. Standard weight per volume figures used in mine waste
calculations are 1.68 tons/y3 or 2 MT/m3.
The approach used here is to estimate the ratio of waste rock production to ore production by mining
category (open-pit and underground); calculate the amount of waste generated from annual production
statistics (also given by mining category); and compare these numbers to waste volumes known or
calculated for various mines.
When the uranium mining industry first started, most of the ores were recovered from deposits located at
or near the surface. Ores were often exposed at the surface and shallow open-pit and underground mines
often followed mineralized zones directly into the subsurface. The open-pit mines would remove thin
overburden from buried parts of the ore body adjacent to the surface exposure. As easily accessible ore
deposits became depleted, mining had to be performed at increasing depths by either open-pit or
underground methods. In addition, lower grade ore deposits, once ignored, were later mined by using
improved mining methods and more efficient ore extraction techniques. In the early mining years, an ore
grade of 0.15% was often ignored; more recent mining practices target ore grades as low as 0.03%.
Accordingly, over the years, the mining industry was required to move larger quantities of topsoil,
overburden, and other waste rock in order to reach deeper deposits.
The amount of overburden that can be economically removed during open-pit mining is a complex
function of the depth to the orebody, the grade and thickness of the ore-bearing zone, the price of
uranium, and the costs of moving the overburden. The costs of processing ore at mills also influence the
economics. Those processing costs, which apply to both underground and surface mines, have steadily
declined and have lowered the ore grade that is economic to mine.
Information about the ratio of waste rock to ore can be derived from Abandoned Mine Land survey
reports written since the mid-1980s, production statistics in files of the U.S. Geological Survey, from
mining journal articles, from detailed descriptions of uranium mining operations in statewide
compilations, and from interviews with mining engineers at selected properties. Such data are available
for mines in Wyoming, Texas, Arizona, and New Mexico (Table AIV.l).
The ratio of waste rock to ore for mines of varying sizes shows that small open-pit mines are highly
variable, but the ratios for the largest mines (greater than 900,000 MTs of ore) tend to range from 8:1 to
20:1. For example, the largest open-pit mine in the United States, the Jackpile-Paguate mine in New
Mexico, was in the 12:1 range through the first 21 years of production (1953-73) but finished with an
overall 16:1 ratio before production ceased in early 1982. The nearby St. Anthony open-pit mine had a
stripping ratio of 10:1. The Shirley basin open-pit complex in Wyoming had an 8:1 waste to ore ratio.
AIV-1

-------
Open-pits in Texas seem to have variable waste to ore ratios ranging from 2:1 to 20:1 for the smaller
older pits on shallow ore bodies to relatively high values of 20:1 to 50:1 for the deeper deposits. Large
open-pits dominate production in Wyoming and New Mexico, whereas smaller open-pits occur in
Colorado, Utah, and Arizona. The Moonlight and Monument #2 open-pits in Arizona are thought to have
had a 5:1 stripping ratio based on the depth to ore and ore thickness (Chenoweth 1998). Smaller open-pit
operations in the range of 900 MTs to 900,000 MTs of ore have waste to ore ratios that generally range
from 10:1 to 30:1.
The Jackpile-Paguate open-pit mine began production in 1953. Between 1953 and early 1963, 70 MMTs
of overburden and associated waste and subore material had been removed to acquire 6.0 MMTs of ore (a
ratio of about 11.8:1, Kittel 1963). By mid-1974, about 110 MMTs of overburden were removed and 9
MMTs of ore were recovered at an average grade of 0.25% (a 12:1 ratio, Graves 1974). Production ceased
in early 1982, with a total of 364 MMTs of overburden and related materials removed from the ore body
and 23 MMTs of ore produced (U.S. BLM 1986), a ratio of 16:1. The mine site contained 32 waste
dumps and 23 protore dumps segregated according to grade. About 10.5 MMTs of protore were stored
outside of the pits, and another 4.5 MMTs in dumps within pits. The ratio of all waste to protore was
about 24:1. About 92 MMTs of backfill, comprised of ore-associated waste and some overburden, were
returned to the pits during operations.
Throughout the 1950s, 1960s, and 1970s, open-pit mining was characterized by numerous small to
moderate-sized open-pit operations with highly variable waste to ore ratios on the Colorado Plateau, by
large open-pit mines in Wyoming and New Mexico with variable but usually lower waste to ore ratios,
and by moderate to large open-pit operations in Texas with generally high waste to ore ratios. In the late
1970s and early 1980s waste to ore ratios for the largest mines appear to have peaked at an average of
about 30:1 (Bohert and Gerity 1978; Facer et al. 1978). As the price of uranium dropped in the early
1980s, only the more efficient open-pit operations remained in production and the waste to ore ratios
probably dropped significantly for the period 1984 to 1992.
Underground mining operations result in much smaller spoil storage piles than those generated by surface
mines. Consequently, the waste to ore ratio generally ranges from 20:1 to 1:1 for underground mines,
with an average ratio of about 9:1 (U.S. EPA 1983b). As with surface mining, this ratio has also increased
over the years from a range of 5:1 until the early 1970s to about 1:1 by the late 1970s.
AIV-2

-------
Table AIV.l Waste to Ore Relation for Mines in Texas, Wyoming, Arizona, and New Mexico
State
Waste in tons
Ore in tons
Ratio
TX
37,300,000
1,945,366
19.2

6,720,000
264,660
25.4

2,040,000
52,390
38.9

220,000
29,000
7.6

138,600
7,899
17.5

168,000
35,495
4.7

5,980,000
117,709
50.8

1,025,000
575,000
1.8

1,610,000
117,775
13.7

5,300,000
148,294
35.7
WY
121,106,000
14,687,480
8.2

405,350,000
10,350,000
39.2

69,050
10,900
6.3

28,900
2,347
12.3

25,200
1,000
25.2

29,700
4,343
6.8

7,728
201
38.4

59,500
1,761
33.8

15,900
256
62.1

34,340
259
132.6

6,540
67
97.6

30,100
153
196.7

42,700
54
790.7

21,190
11
1926.4

27,330
1,056
25.9

9,160
358
25.6

134,160
2,175
61.7

3,440
61
56.4

16,300
95
171.6

72,996
2,341
31.2

91,140
3,800
24.0

154,812
4,000
38.7

4,032
975
4.1

25,450
22
1156.8

10,350
63
164.3
AIV-3

-------
Table AIV.l Waste to Ore Relation for Mines in Texas,
Wyoming, Arizona, and New Mexico (cont.)
State
Waste in tons
Ore in tons
Ratio
WY (cont.)
20,160
62
325.2

7,190
7,130
1.0

18,600
134
138.8

37,800
1,270
29.8

16,180
284
57.0

22,390
1,345
16.6

7,140
462
15.5

18,300
1,471
12.4

46,940
485
96.8

3,090
387
8.0
AZ
758
3
252.7

42,000
926
45.4

202
7
28.8

3,920
109
36.0

61
6
10.1

55,200
1,363
40.5

706
123
5.7

12,440
586
21.2

4,200
305
13.8

15,750
794
19.8

958,220
33,821
28.3

7,390
563
13.1

226,800
1,264
179.4

294,000
1,128
260.6

19,320
218
88.6

14,950
1,042
14.3

2,100
23
91.3

196,560
2,829
69.5

22,340
343
65.1

31,080
1,610
19.3
NM
364,000,000
23,000,000
15.8

St. Anthony Pit

10.0

50,000
10,400
4.8
Sources: AVI 1986, HE 1987, RCT1994, Kittel 1963, SRB 1981, Chenoweth 1998, McLenore 1983, Finch 1998.
AIV-4

-------
Uranium ore production rates since 1948 for conventional mining techniques and related
production amounts of overburden are given in Table AIV.2. As shown in the table, the estimates
for surface mine ratios (overburden to ore) are based on a factor of 30 for the entire period. This
approach is believed to arrive at a total waste number for open-pit mines that seems reasonable (i.e.
should not significantly over- or underestimate the number), considering the waste volumes
associated with the largest mines (see discussion below).
For underground mines, a ratio of 3:1 was used for the years 1948-1970, and 1:1 was used for
1971 and later on. Despite the earlier EPA estimate mentioned previously, it is believed that
applying a single ratio of 9:1 for all years would significantly underestimate the amount of waste
generated during the last two decades.
Based on the preceding discussion, the total overburden produced by open-pit mines is estimated to
range from 1 billion metric tons to 8 billion metric tons, with an average of 3 billion metric tons.
For underground mines, the estimate ranges from 5 MMTs to 1 hundred MMTs, averaging 67
MMTs. Waste produced by open-pit mining is a factor of 45 greater than that for underground
mining, based on their respective averages. For the range between the low and high estimates, the
factor is 190 for the low estimate and 80 for the higher one. Thus, the amount of overburden
generated from open-pit mines far exceeds that from underground mines.
The four largest mines in Table AIV. 1 yield about 30% of the surface mine total; however, the size
of mines drops dramatically as the rest of the inventory is considered. More than 1,000 of the 1,300
surface mines that have been operated in the past 50 years have produced less than 900 MTs of ore.
These mines total less than 30 MMTs of waste, or less than 1% of the median estimate.
Accordingly, the waste inventory produced by this industry is primarily the result of past
operations at some 300 surface mines (SC&A 1989).
AIV-5

-------
Year
1948
1949
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
Table AIV.2. Uranium Ore Production Rates and Overburden 1948—1996
Ore (MTs)
Open-Pit Mining
Overburden (MTs)
Low
Avg.
High
Ore (MTs)
Underground Mining
Overburden (MTs)
Low
Avg.
<9.0E+02
9.1E+03
2.7E+04
7.3E+04
3.4E+04
1.7E+03
1.1E+04
9.1E+02
9.1E+03
2.7E+04
7.3E+04
1.6E+05
7.8E+03
5.2E+04
2.1E+04
2.1E+05
6.3E+05
1.7E+06
2.1E+05
1.0E+04
6.9E+04
2.5E+04
2.5E+05
7.6E+05
2.0E+06
2.9E+05
1.4E+04
9.6E+04
5.9E+04
5.9E+05
1.8E+06
4.7E+06
3.4E+05
1.7E+04
1.1E+05
1.6E+05
1.6E+06
4.9E+06
1.3E+07
5.0E+05
2.5E+04
1.7E+05
2.4E+05
2.4E+06
7.2E+06
1.9E+07
7.6E+05
3.8E+04
2.5E+05
3.4E+05
3.4E+06
1.0E+07
2.7E+07
1.0E+06
5.2E+04
3.5E+05
1.1E+06
1.1E+07
3.4E+07
9.1E+07
1.6E+06
8.0E+04
5.3E+05
1.5E+06
1.5E+07
4.4E+07
1.2E+08
1.9E+06
9.4E+04
6.3E+05
2.1E+06
2.1E+07
6.4E+07
1.7E+08
2.6E+06
1.3E+05
8.5E+05
2.0E+06
2.0E+07
6.0E+07
1.6E+08
4.3E+06
2.2E+05
1.4E+06
2.2E+06
2.2E+07
6.5E+07
1.7E+08
5.1E+06
2.5E+05
1.7E+06
2.3E+06
2.3E+07
6.8E+07
1.8E+08
5.0E+06
2.5E+05
1.7E+06
1.6E+06
1.6E+07
4.8E+07
1.3E+08
4.8E+06
2.4E+05
1.6E+06
1.7E+06
1.7E+07
5.1E+07
1.4E+08
3.7E+06
1.8E+05
1.2E+06
1.4E+06
1.4E+07
4.2E+07
1.1E+08
3.4E+06
1.7E+05
1.1E+06
1.1E+06
1.1E+07
3.4E+07
9.0E+07
2.8E+06
1.4E+05
9.5E+05
1.2E+06
1.2E+07
3.6E+07
9.7E+07
2.7E+06
1.4E+05
9.1E+05
1.4E+06
1.4E+07
4.3E+07
1.2E+08
3.4E+06
1.7E+05
1.1E+06
2.1E+06
2.1E+07
6.4E+07
1.7E+08
3.7E+06
1.9E+05
1.2E+06
2.0E+06
2.0E+07
5.9E+07
1.6E+08
3.4E+06
1.7E+05
1.1E+06
2.5E+06
2.5E+07
7.6E+07
2.0E+08
3.2E+06
1.6E+05
1.1E+06
3.0E+06
3.0E+07
8.9E+07
2.4E+08
2.7E+06
1.4E+05
2.7E+06
3.5E+06
3.5E+07
1.1E+08
2.8E+08
2.3E+06
1.1E+05
2.3E+06
4.1E+06
4.1E+07
1.2E+08
3.3E+08
1.8E+06
9.0E+04
1.8E+06
3.8E+06
3.8E+07
1.1E+08
3.1E+08
2.6E+06
1.3E+05
2.6E+06
3.9E+06
3.9E+07
1.2E+08
3.1E+08
2.5E+06
1.3E+05
2.5E+06
4.2E+06
4.2E+07
1.3E+08
3.4E+08
3.6E+06
1.8E+05
3.6E+06
5.1E+06
5.1E+07
1.5E+08
4.0E+08
4.3E+06
2.2E+05
4.3E+06
7.5E+06
7.5E+07
2.2E+08
6.0E+08
5.5E+06
2.8E+05
5.5E+06
8.8E+06
8.8E+07
2.6E+08
7.0E+08
4.9E+06
2.4E+05
4.9E+06
9.4E+06
9.4E+07
2.8E+08
7.5E+08
5.8E+06
2.9E+05
5.8E+06
7.7E+06
7.7E+07
2.3E+08
6.1E+08
4.7E+06
2.4E+05
4.7E+06
5.0E+06
5.0E+07
1.5E+08
4.0E+08
2.5E+06
1.3E+05
2.5E+06
4.4E+06
4.4E+07
1.3E+08
3.6E+08
2.3E+06
1.1E+05
2.3E+06
AIV-6

-------
Table AIV.2. Uranium Ore Production Rates and Overburden 1948—1996 (cont.)
Year
Open-Pit Mining
Underground Mining
Ore (MTs)
Overburden (MTs)
Ore (MTs)
Overburden (MTs)
Low
Avg.
High
Low
Avg.
High
1984
1.8E+06
1.8E+07
5.4E+07
1.4E+08
9.3E+05
4.7E+04
9.3E+05
9.3E+05
1985
8.5E+05
8.5E+06
2.5E+07
6.8E+07
5.2E+05
2.6E+04
5.2E+05
5.2E+05
1986
1.3E+05
1.3E+06
3.8E+06
1.0E+07
6.0E+05
3.0E+04
6.0E+05
6.0E+05
mr
1.7E+05
1.7E+06
5.1E+06
1.4E+06
7.8E+05
3.9E+04
4.6E+05
4.6E+05
1988"
6.5E+05
6.5E+06
2.0E+07
5.2E+07
8.5E+05
4.3E+04
4.7E+05
4.7E+05
1989a
6.2E+05
6.2E+06
1.9E+07
5.0E+07
7.3E+05
3.7E+04
7.3E+05
7.3E+05
1990a
2.9E+05
2.9E+06
8.7E+06
2.3E+07
2.8E+05
1.4E+04
2.8E+05
2.8E+05
1991"
6.0E+05
6.0E+06
1.8E+07
4.8E+07
6.0E+05
3.0E+04
6.0E+05
6.0E+05
1992
<9.0E+02
—
—
-
<9.0E+02
—
-
-
1993
none
-
-
-
none
-
-
-
1994
none
—
—
-
none
-
-
-
1995
none
-
-
-
none
-
-
-
1996
none
—
-
-
<9.0E+02
-
-
-
Total
1.03E+08
1.03E+09
3.08E+09
8.21E+09
1.06E+08
5.29E+06
6.91E+7
1.06E+08
1948-1987

1.0E+09
3.0E+09
8.0E+09

5.2E+06
6.7E+07
1.0E+08
1987-1996

2.3E+07
6.7E+07
1.7E+08

1.6E+05
2.5E+06
2.5E+06
" Ore volumes not reported by mining category; volumes based on annual average uranium content of ore.
AIV-7

-------
Appendix V. Radiochemical Data for Uranium Overburden and Waste Rock,
Pit Lakes and Streams, and In Situ Leach Operations
Introduction
The following tables present radionuclide concentration data on solid and liquid wastes at conventional
mines, pit lakes and streams, and from in situ leach operations. The data compiled has come from a wide
variety of sources, many or most without uncertainty limits on the data provided. However, the
information is instructive in providing a range of values for these wastes from numerous mines and
facilities throughout the west.
In several of the sources, measurements were reported for samples taken from conventional mine "waste"
or "spoils" or "dumps" without distinguishing between overburden, soil, or waste rock, or potentially
protore. Nevertheless, those studies provide a sense of how radioactive the wastes may be at those sites.
AV-1

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
AVI 1991
Avg. of 54
analyses
30.7
(1.14)
15.2
(0.56)


Bullrush spoils,
drill hole data
Range of 54
analyses
2-299
(0.07-3.7)
2-140
(0.07-5.18)


Whitworth 1996
Mine waste, avg.
24.4
(0.9)
28.2
(1.04)


La Bajada Mine,
NM
Pro tore, avg.
75
(2.78)
613.5
(2.28)


PEDCO 1983
Protore, NM
59
(2.18)
78.4
(0.259)


Protore
71.4
(2.64)
51.4
(1.9)


Protore
112
(4.14)
88.9
(3.29)


Protore
122
(4.51)
55.8
(2.06)


Protore
63.7
(2.36)
66.4
(2.46)


Waste
1.47
(0.05)
1.71
(0.06)


Waste
9.3
(0.34)
7.8
(0.29)


Waste
4.2
(0.16)
3.5
(0.13)


Waste
34.5
(12.77)
30
(1.11)


Protore, WY
8.55
(0.32)
37.4
(1.38)


Waste
17.6
(0.65)
1.17
(0.04)


Waste
1.35
(0.05)
10.8
(0.4)


Soil
0.51
(0.02)
0.71
(0.02)


Protore
129
(4.77)
82.2
(0.3)


Waste

1.23
(0.05)


Waste

0.81
(0.03)


Waste
0.61
(0.02)
3.2
(0.12)


Waste
1.17
(0.04)
1.06
(0.04)


Protore
54.4
(2.0)
67.9
(2.51)


AV-2

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
PEDCO 1983
(cont.)
Waste
0.93
(0.03)
2.15
(0.08)



Waste
0.18
(0.01)
2.74
(0.1)



Soil
1.55
(0.11)
1
(0.04)



Protore
97.1
(3.59)
148
(0.67)



Waste
7.1
(0.26)
5
(0.19)



Waste
4.9
(0.19)
6.3
(0.23)



Soil
4
(0.15)
3.9
(0.14)



Waste, jxg
26.4
32.4



Waste, |xg
5.8
6.1



Waste, |ig
15.7
11.6



Waste, |xg
24
16.4



Waste, jxg
58.3
31.9



Waste, |xg
58.7
39.4



Waste
6.2
(0.23)
4.4
(0.16)



Protore
137
(5.07)
118
(4.37)



Waste
30.5
(1.13)
25.8
0.95)



Protore
215
(7.96)
76.5
(2.83)



Waste
30.8
(1.14)
27.9
(1.03)



Waste
23.9
(0.88)
17.2
(0.04)



Waste, |xg
54.3
40



Waste, |xg
12.4
8


EPA 1983
Boulder sites


40-100


Uravan


50-220


S.M., waste


35-275


ore


100-350


overburden


20-120


below ground


10-13

AV-3

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
EPA 1983
(cont.)
Mesa Top, waste


25-290

Barb Jo, waste


2-170

Poison C.,waste


65-250

overburden


25-65

Morton R.,
protore


200

overburden


59-138

Burghardt 1998
Various surveys
Orphan (|xg), AZ
median


250

San Mateo (|xg)
spoils


10-450

SanM.,NMavg.


200

Lathrop mine
(|xg), waste


270-400




250




170-180


212
(7.84)
54
(2.0)



57
(2.11)
81
(3.0)



2.7
(0.1)
6.3
(0.23)



40
(1.48)
47
(1.74)


Muss

4.3
(0.16)




1.28
(0.05)




4.3
(0.16)


Jomac
163
(6.03)
110
(4.1)



35
(1.3)
206
(7.62)


Cath. Butte
17
(0.63)
25
(0.93)


Blue N.
7.3
(0.28)
8.5
(0.31)



22
(0.81)
26
(0.96)


W. Rk. Cn.
15.3
(0.57)
18
(0.67)



32
(0.67)
21
(0.78)


Terry
188
(6.96)
170
(6.29)


AV-4

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
Burghardt 1998
Various surveys
(cont.)

2.3
(0.09)
3.2
0.12)


Rainy Day
70
(2.59)
48
(1.78)



56.7
(2.1)
1.5
(0.06)



1.7
(0.06)
3.8
(0.14)



3.1
(0.11)
12
(0.44)


Longsworth 1994
Monument Valley
Cameron area
AZ/UT


Moonlight Mine


18-22




43-630




185-320

Jeepster


18-23




19-20




5-20




47-150

Jack Daniels


70-190




35-220




27-85




33-75

Moore et al. 1996
South spoil, drill
hole avg.
85 ppm



Midnite Mine,
WA
Hillside spoil,
drill hole avg.
82 ppm



AVI 1986
Shirley Basin,
WY




all piles, avg.

11.5
(0.43)


LAI 1996
Rox ore pile, avg.


400

GV area, avg.


120

H&I, avg.


150

G spoils, avg.


150

Stan claims, avg.


500

B/R spoils, avg.


150

2States/Bl, avg.


250

Umetco, spoils, E


120

S


280

Sunset sp, avg.


200

max.


2,000

S-T spoils


50-150

Bullrush, avg.


90

P73 av


300

Classic/Bar
protore


300-500

North Rex, avg.


40

AV-5

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
HE 1989
Pix-Veca pile,
drill hole avg.

11.4
(0.42)


P-V, avg. 1,200
meas.


113
(4.2)

P-V surface avg.

27.2
(1.0)


AVI 1990
Poison Basin-
protore

55-140
(2.04-5.18)
250-600

HE 1987
Pump Bts. Smpls
35
(1.3)
87
(3.22)
170


52
(1.92)
126
(0.44)
300


27
(1.0)
45
(1.67)
105


2.1
(0.08)
9
(0.33)
70

Jean-avg. ore
piles


140

Key- below
ground
22.1
(0.82)
12.7
(0.47)
40

waste
20.9
(0.77)
32.8
(1.21)
70

ore
688
(25.46)
185.6
(68.67)
300

FPE1988
Gas Hills-Jgpile,
avg.

33.8


Jpile, avg.

15.5
(0.57)


Kpile, avg.

7.2
(0.27)


WY AML Project
15
Converse County,
WY




Avg. of 677,482
yds




of protore
170 ppm



Site II-avg.

51
(1.89)
74
30.7
(1.14)
range

17-180
(0.63-6.67)
3.4-160

Average all drill
hole in
waste/protore
piles 11 sites
93.6ppm
49.6
(1.84)


RCT 1994
Range of 82
smpls of
soil/spoil from 10
sites
<.85-668 ppm



AV-6

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
U.S. BLM 1986
Jackpile-Paguate,
NM




Dump A waste
4.5 ppm

11
(0.41)

B waste
2.7 ppm

10
(0.37)

C waste
2.7 ppm

5
(0.19)

D waste
4.05 ppm

5
(0.19)

E waste
1.5 ppm

5
(0.19)

F waste
4.03 ppm

5
(0.19)
1.1
(0.04)
G waste
5.82 ppm

5
(0.19)
4.15
(0.15)
H waste
146.8 ppm

29
(1.07)

I waste
10.0 ppm

5
(0.19)

J waste
10.66 ppm

75
(2.78)

K waste
20.30 ppm

7
(0.26)
2.7
(0.10)
L waste
5.5 ppm

5
(0.19)
2.57
(0.1)
N waste
42.0 ppm

9
(0.33)

N2 waste
200.0 ppm

30
(1.11)

O, P,P1,P2
waste
3.12 ppm

12
(0.44)

Q waste
160.0 ppm

68
(2.52)

R waste
11.0 ppm

24
(0.89)

S waste
2.79 ppm

10
(0.37)

T waste
3.9 ppm

9
(0.33)

U waste
34.3 ppm

52
(1.92)

V waste
13.9 ppm

34
(1.26)

W waste
2.5 ppm

10
(0.37)

X waste
18.0 ppm

5

Y waste
33.4 ppm

13

AV-7

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
U.S. BLM 1986
Y2 waste
4.2 ppm

5

(cont.)
South waste
4.9 ppm

8


FD-1 waste
2.7 ppm

10


FD-2 waste
45.0 ppm

3


FD-3 waste
14.0 ppm

28


17BC pro tore
220.0 ppm

581


6A protore
200.0 ppm

388


6B protore
130.0 ppm

383


J1 protore
94.0 ppm

155


J2 protore
490.0 ppm

606


17D protore
520.0 ppm

198


IB protore
140.0 ppm

237


2C protore
110.0 ppm

422


10 protore
390.0 ppm

506


2D protore
180.0 ppm

419


1C protore
61.0 ppm

227


1A protore
31.0 ppm

161


2E protore
220.0 ppm

451


SP-1 protore
130.0 ppm

354


PLG protore
5.0 ppm

210


4-1 protore
77.0 ppm

266


SP-2 protore
180.0 ppm

300


SP-2B protore
610.0 ppm

164


TS-1 soil pile
4.9 ppm

8


TS-2A soil pile
4.9 ppm

18


TS-2B soil pile
2.9 ppm

6


TS-3 soil pile
3.6 ppm

11


Topsoil borrow
4.1 ppm

17

Otton 1998
Ascension mine
Front Range of
CO




Waste/prot avg.
41 sites

45.7
(1.69)



Protore range

294-421
(10.88-15.58)
680-1,100

AV-8

-------
Table AV.2 Radionuclide Concentrations in Ponds and Streams Associated
with Open-pit Mines in Arizona, Texas, Utah and New Mexico
Data Source
Type of Data
U-238
PPb
U-235
pCi/L
Ra-226
pCi/L
Longsworth 1994
Monument Valley
area, AZ-UT




Moonlight
Mine—shallow well
11000
440
(1.63)
44
(1.63)
AZ-UT deposits
Moonlight
Mine—shallow well
14000
530
(19.61)
110
(4.07)

Moonlight Mine—pit
water
-
-
8.6
(0.32)

Radium
Hill—drillhole water
210
12
(0.04)
19
(0.7)

Radium Hill—shallow
well
0.5
<0.1
0.16
(0.01)

Cameron area, AZ




Jeepster Mine—pit
water
22
0.8
(0.03)
0.25
(0.01)

Jack Daniels
Mine—ground water
150
5.7
(0.21)
0.1

Jack Daniels
Mine—pit water
11
0.4
(0.01)
0.07

Manuel-Denetsone
—drillhole water
180
8.9
(0.33)
0.52
(0.02)

Ramco No. 20—small
pit water
15
0.6
(0.02)
0.09


Uppb


RCT 1994
Texas mines.
Open-pit mine water
samples




Stoeltje
600




700



Manka
250




200




300




220



I.M. Brysch
12




<1




14



Galen
<1



Butler
180




180




42




45




<1




<1




65


AV-9

-------
Table AV.2 Radionuclide Concentrations in Ponds and Streams Associated
with Open-pit Mines in Arizona, Texas, Utah and New Mexico
(cont.)
Data Source
Type of Data
U-238
PPb
U-235
pCi/L
Ra-226
pCi/L
RCT 1994
Wright-McCrady
49


Texas mines.

49


(cont.)
Esse
49




49



Sickenius
240




230



Kopplin
72




82



Smith
4,500




4,500



Pfeil
57




25



Weddington South
25




49



Kellner-T enneco
Weddington
220




170




200




300



Franklin
18




7


U.S. BLM 1986
South Paguate—pit
pond, N.M.


21.1
(0.78)

North Paguate—pit
pond


36
(1.33)

South Jackpile—pit
pond


18
(0.67)

North Jackpile—pit
pond


16.1
(0.60)

Rio
Paguate—upstream
from mine
6

0.35
(0.01)

Rio
Moquino—upstream
from mine
8

0.28
(0.01)

Below
confluence—down
from mine
239

3.73
(0.14)

Paguate
Reservoir—down from
mine
236

1.03
(0.04)
AV-10

-------
The following licensed ISL facilities are under the environmental oversight and regulation of the NRC
and its Agreement States. The wastes from these facilities are considered byproduct materials and not
TENORM. The information presented here is for information purposes only.
Table AV.3. In Situ Leach Operation Evaporation Pond Radionuclides,
Crow Butte, Nebraska
Radionuclides
Pond Liauids (uCi/mh
Lead-210
0.66 x 10-9
Polonium-210
0.70 x 10-9
Radium
0.65 x 10-9
Radon
0.70 x 10-4
Thorium-230
2.28 x 10-9
Uranium
5.24 x 10-9
Source: NRC License Application Supporting Materials.
AV-11

-------
Table AV.4.1 In Situ Leach Operation Evaporation Pond Radionuclides COGEMA,
Irigaray Field, Wyoming
Sample Loc. /Date
Total U
mg/L
Ra 226 pCi/L
+/- Precision
Ra 226 Bq/L
+/- Precision
IR-1 01/21/99
7.0
3.9/0.3
0.14/0.01
IR-1 04/16/99
18.3
8.1/0.5
0.30/0.02
IR-2A 01/21/99
15.1
46.3/1.9
1.71/0.07
IR-2A 04/16/99
1.90
68.9/2.4
2.55/0.9
IR-2B 01/21/99
6.0
29.1/1.5
1.08/0.07
IR-2B 04/16/99
3.96
50.5/2.0
1.87/0.07
IR-3 01/21/99
1.9
17.3/1.3
0.64/0.05
IR-3 04/16/99
0.746
8.4/0.5
0.31/0.02
IR-A 01/21/99
39.8
135/4.2
5.0/0.16
IR-A 04/16/99
36.0
151/4.7
5.59/0.17
IR-B 01/21/99
11.5
471/7.8
17.43/0.29
IR-B 04/16/99
11.8
439/7.9
16.24/0.29
IR-C 01/21/99
3.2
439/7.4
16.24/0.3
IR-C 04/16/99
3.0
325/5.4
12.03/0.2
IR-D 01/21/99
6.6
580/8.6
21.46/0.32
IR-D 04/16/99
6.0
529/6.6
19.57/0.24
IR-E 01/21/99
13.6
1,716/14.6
63.49/0.54
IR-E 04/16/99
13.4
1,760/12.3
65.12/0.46
IR-RA 01/21/99
3.0
16.9/1.2
0.63/0.04
IR-RA 04/16/99
31.0
39.0/1.9
1.44/0.07
IR-RB 01/21/99
46.5
5.1/0.4
0.19/0.01
IR-RB 04/16/99
86.0
11.5/1
0.43/0.04
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-12

-------
Table V.4.2. In Situ Leach Operation Evaporation Pond Radionuclides COGEMA,
Christensen Ranch Field, Wyoming
Samnle T.nc. /Date
Total TT
Ra 226 nCi/T,
Ra 226 Rn/T,
CR-1 01/21/99
8.6
107/2.9
3.96/0.11
CR-1 04/16/99
6.6
97.5/2.8
3.61/0.1
CR-2 01/21/99
1.10
1.5/0.2
0.06/0.01
CR-2 04/16/99
18.10
3.1/0.3
0.11/0.01
CR-3 01/21/99
0.443
1.4/0.2
0.05/0.007
CR-3 04/16/99
2.00
37.8/1.8
1.4/0.07
CR-4 01/21/99
0.07
1.5/0.2
0.06/0.007
CR-4 04/16/99
0.3160
23.7/1.4
0.88/0.05
CR-P1 01/21/99
0.021
0.8/0.2
0.03/0.007
CR-P1 04/16/99
0.0166
6.0/0.4
0.22/0.15
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-13

-------
Table AV.5. In Situ Leach Operation Evaporation Pond Radionuclides,
Power Resources, Inc. Highlands Uranium Project, Wyoming
Purge Storage Reservoir PSR-1
Purge Storage Reservoir PSR-2
Date
Ra-226
Date
Ra-226
pCi/L
Bq/L
pCi/L
Bq/L
01/10/97
3.14
0.12
01/09/97
5.50
0.20
02/03/97
1.36
0.05
02/07/97
2.47
0.09
03/05/97
2.26
0.08
03/05/97
3.70
0.14
04/01/97
2.10
0.07
04/03/97
9.50
0.35
05/05/97
2.00
0.07
05/08/97
7.45
0.27
06/03/97
2.10
0.07
06/18/97
1.20
0.04
07/02/97
2.24
0.08
07/03/97
2.15
0.08
08/04/97
1.50
0.06
08/01/98
4.50
0.17
09/03/97
5.60
0.21
09/05/97
4.20
0.16
10/02/97
1.34
0.05
10/16/97
1.38
0.05
11/06/97
4.13
0.15
11/13/97
5.60
0.21
10/01/97
2.36
0.09
12/03/97
8.10
0.30
01/05/98
6.70
0.25
01/06/98
2.30
0.09
02/02/98
2.68
0.10
02/10/98
3.60
0.13
03/02/99
2.99
0.11
03/10/99
3.10
0.11
04/07/98
1.21
0.04
04/06/98
1.71
0.06
05/04/98
3.60
0.13
05/07/98
2.10
0.08
06/03/98
4.10
0.15
06/09/98
4.00
0.15
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-14

-------
Table AV.5. In Situ Leach Operation Evaporation Pond Radionuclides,
Power Resources, Inc. Highlands Uranium Project, Wyoming (cont.)
E Radium Settling Basin
W Radium Settling Basin
Date
U Total
Ra-226
U Total
Ra-226
pCi/L
Bq/L
pCi/L
Bq/L
pCi/L
Bq/L
pCi/L
Bq/L
03/20/97
4.60
0.17
1.30
0.05
5.30
0.20
8.30
0.31
06/30/97
3.00
0.11
5.10
0.19
3.00
0.11
5.10
0.19
09/03/97
2.26
0.08
8.00
0.30
2.18
0.08
1.20
0.04
12/30/97
5.96
0.22
7.00
0.26
4.29
0.16
1.10
0.04
03/24/98
4.80
0.18
1.20
0.04
3.61
0.13
2.80
0.10
06/22/98
4.85
0.18
1.30
0.05
2.26
0.08
9.00
0.33
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-15

-------
Table AV.6. In Situ Leach Operation Evaporation Pond Radionuclides Rio Algom
Mining Corp. (Now owned by Power Resources) Smith Ranch Project, Wyoming
Evaporation Pond Water Analyses Q&S Sand In Situ Leaching
Location
Date
East Cell
West Cell
II mg/L
Ra226
pCi/L (Bq/L)
Th230
pCi/L (Bq/L)
II mg/L
Ra226
pCi/L (Bq/L)
Th230
pCi/L (Bq/L)
1st Qtr. 1982
1,100
2,378 (87.99)

16
172 (6.36)

2nd Qtr. 1982
784
456 (16.88)

49
1,804 (66.75)

3rd Qtr. 1982
38
100 (3.7)

132
2,119(78.4)

4th Qtr. 1982
275
315 (11.66)

131
1,779 (65.82)

1st Qtr. 1983
4
86 (0.15)

2
22 (0.81)

2nd Qtr. 1983
79
216(0.96)

1
36(1.33)

3rd Qtr. 1983
13
108 (0.07)

14
44(1.63)

4th Qtr. 1983
103
483 (17.87)

100
553 (20.46)

1st Qtr. 1984
22
42(1.55)

1
34(1.26)

2nd Qtr. 1984
55
183 (6.77)

121
224 (8.29)

3rd Qtr. 1984
105
21 (0.78)

105
7 (0.26)

4th Qtr. 1984
141
5,095 (188.52)

--
--

1st Qtr. 1985
12
3,030 (112.11)

	
	

2nd Qtr. 1985
.20
643 (23.79)

.17
1,149 (42.51)

3rd Qtr. 1985
.23
510(18.87)

.23
490(18.13)

4th Qtr. 1985
.21
754 (27.90)

.22
552 (20.42)

1st Qtr. 1986
.33
184 (6.8)

.14
423 (15.65)

2nd Qtr. 1986
.25
1,366 (50.54)

.20
923 (34.15)

3rd Qtr. 1986
.39
3,253 (120.36)

.38
2,081 (77.0)

4th Qtr. 1986
.32
4(0.15)

.27
41 (1.52)

1st Qtr. 1987
.24
772 (2.86)

.25
755 (27.94)

2nd Qtr. 1987
.25
1912 (70.74)

.23
560 (20.72)

1st Half 1997
69.7
3,230 (119.51)
15.4 (0.57)
137
74.6 (2.76)
1.1 (0.04)
2nd Half 1997
27.8
57.1 (2.11)
0



2nd Half 1999
92.4
945 (34.97)
6.2 (0.23)
70.8
203 (0.1)
0.7(0.03)
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-16

-------
The evaporation ponds were being sampled semiannually. Gamma radiation was measured quarterly at
the evaporation ponds. The measurements obtained during the 1st & 2nd quarters of 1999 were 71 and 27
uR/hr, respectively.
Table AV.7. Evaporation Pond Leaks, Smith Ranch Project, Wyoming
Location
Date
U (nat) mg/L
East Pond
01/13/99
6.19
East Pond Stand Pipe
01/13/99
6.89
East Pond Stand Pipe
02/08/99
25.8
East Pond Sump
05/04/99
28
West Pond Sump
05/04/99
65
West Pond Sump
06/25/99
166
West Pond
10/23/99
75
West Pond Sump
10/23/99
193
West Pond Sump
10/29/99
150
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
Table AV.8. Deep-well Injection, Smith Ranch In Situ Leach Facility, Wyoming
The following is a table of the amounts and concentration of U Nat & Ra-226
disposed by UIC injection in 1998, 1999.
Date
Gals./month (liters/month)
Nat. Uranium mg/L *
Radium-226 pCi/L*
(Bq/L)
June 1998

27.5
1,250 (46.25)
Sept. 1998

5.0
1,300 (48.10)
Dec. 1998

17.5
1,550 (57.35)
Jan. 1999
1,869,362 (7,076,095.9)


Feb. 1999
1,832,431 (6,936,722.5)


Mar. 1999
1,867,385 (7,068,612.4)
10.0
1,450 (53.65)
April 1999
1,906,162 (7,215,395.0)


May 1999
1,952,301 (7,390,044.9)


June 1999
1,713,467 (6,485,960.1)
19.0
1,050 (38.85)
* = Values estimated from graph.
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-17

-------
Appendix I. List of Acronyms and Abbreviations,
and Glossary of Terms
List of Acronyms and Abbreviations
Ac
actinium
ac
acre
ac-ft
acre-feet
ACAA
American Coal Ash Association
AEA
Atomic Energy Act
AEC
Atomic Energy Commission
ALARA
As low as reasonably achievable
AML
abandoned mine lands
As
arsenic
ATSDR
Agency for Toxic Substances and Disease Registry
Ba
barium
BASINS
Better Assessment Science Integrating Source and Non-point Sources (USGS

computer model)
BAT
best achievable technology
Bi
bismuth
BPCT
best practicable control technology
Bq/kg
Becquerel/kilogram.
BRC
Bureau of Radiation Control
CAA
Clean Air Act
CaS04
calcium sulphate (formula for gypsum)
CERCLA
Comprehensive Environmental Response, Compensation and Liability Act

(Superfund)
CFR
Code of Federal Regulations
Ci
Curie(s) (unit of radioactivity, 3.7 x 1010 disintegrations per second)
cm
centimeter
COD
chemical oxygen demand
Cr
chromium
CRCPD
Conference of Radiation Control Program Directors
Cu
copper
CWA
Clean Water Act
D&D
decontamination and decommissioning
DOE
Department of Energy
DOI
Department of the Interior
dscm
dry standard cubic meter
E
used to denote exponents (3.7E+10)
EIA
Energy Information Administration (U.S. Department of Energy)
EPA
Environmental Protection Agency
ESRI
Environmental Systems Research Institute
°F
degrees Fahrenheit
Fe
iron
FeCl3
ferric chloride
FeP
ferro-phosphorus
FeS2
pyrite
FIPR
Florida Institute of Phosphate Research
Fr
francium
AI-l

-------
ft	feet
g	gram
g/cm3	gram per cubic centimeter
Gy	Gray
H	hydrogen
ha	hectare, 2.471 acres
HDS	high-density sludge
Hg	mercury
hr	hour
ISL	in situ leaching
K	potassium
Kd	element-specific soil-water partition coefficient
kg	kilogram
L	liter
LTSP	long-term surveillance plan
(j,	micro, 10"6, used in combination with specific units
|ig/m	microgram per meter
(.ig/ni3	microgram per cubic meter
(j,m	one-millionth of a meter (micron)
(j,R/hr	microRoentgen per hour
m	milli, 10"3, used in combination with specific units
m	meter
m2	square meter
m2/s	square meters per second
m3	cubic meter
MAS/MILS Minerals Availability System/Minerals Industry Location System (USGS
database)
mbd	million barrels per day
MCL	maximum contaminant level
mg	milligram
mL	milliliter
Mn	manganese
Mo	molybdenum
MOU	memorandum of understanding
mrem	millirem
mR/hr	milliRoentgen per hour
mSv	milliSievert
MT	metric ton(s), 1000kg, or 2,200 lb
MMTs	millions of metric tons
n	nano, 10"9, used in combination with specific units
NAAQS	National Ambient Air Quality Standards
NAMLRP	Navajo Abandoned Mine Lands Reclamation Program
NARM	naturally occurring and accelerator-produced radioactive material
NAS	National Academy of Sciences
NCRP	National Council on Radiation Protection and Measurements
NEPA	National Environmental Policy Act
NESHAP	National Emission Standards for Hazardous Air Pollutants
NFS	National Forest Service
NNEPA	Navajo Nation Environmental Protection Agency
NORM	naturally occurring radioactive material
NPDES	National Pollutant Discharge Elimination System
AI-2

-------
NPL	National Priorities List
NPS	National Park Service
NRC	Nuclear Regulatory Commission
NSPS	New Source Performance Standards
02	oxygen
ORIA	Office of Radiation and Indoor Air (U.S. EPA)
OSM	Office of Surface Mining
p	pico, 10"12, used in combination with specific units
Pa	protactinium
Pb	lead
pCi/g	picocurie per gram
pCi/L	picocurie per liter
pCi/m2/s	picocurie per meter squared per second
pH	negative log of hydrogen ion concentration (measure of acidity and alkalinity)
Po	polonium
ppb	parts per billion, 10"9
ppm	parts per million, 10"6
Pu	plutonium
QA/QC	quality assurance/quality control
R	Roentgen
r2	correlation coefficient
Ra	radium
RCRA	Resource Conservation and Recovery Act
Rem	Roentgen equivalent in man
RESRAD	computer model to evaluate risks/doses from RESidual RADiation materials
(DOE's Argonne National Laboratory)
ROD	record of decision (Superfund)
s	second
SAB/RAC	Science Advisory Board/Radiation Advisory Committee (with U.S. EPA)
SARA	Superfund Amendments and Reauthorization Act
SDWA	Safe Drinking Water Act
Se	selenium
SEO	State Engineer's Office
SIP	State Implementation Plans
SMCRA	Surface Mining Control and Reclamation Act
Sr	strontium
SSL	soil screening level, in pCi/g
Sv	Sievert
tpd	tons per day
TDS	total dissolved solids
TENORM	technologically enhanced, naturally occurring radioactive material
Th	thorium
T1	thallium
TNRCC	Texas Natural Resources Conservation Commission (now Texas Commission on
Environmental Quality)
TRC	Texas Railroad Commission
TSD	treatment, storage, and disposal
TSS	total suspended solids
TWC	Texas Water Commission
U	uranium
U308	oxide of uranium
AI-3

-------
U4+T1206
brannerite
UIC
underground injection control
UMTRA
Uranium Mill Tailings Remedial Action program (U.S. DOE)
UMTRCA
Uranium Mill Tailings Radiation Control Act of 1978
UNSCEAR
United Nations Scientific Committee on the Effects of Atomic Radiation
uo2
uranium dioxide
U02S04
uranium sulfate
USiO4B«H20
coffinite
U.S. ACE
U.S. Army Corps of Engineers
USDA
U.S. Department of Agriculture
3
y
cubic yard(s)
Glossary of Terms
Adits	Horizontal or nearly horizontal passages driven from the surface for the
working or dewatering of a mine. If driven through a hill or mountain to
the surface on the other side it would be a tunnel.
ALARA
Alpha Particle
Aquifer
Background
Becquerel (Bq)
Acronym for As Low As Reasonably Achievable: A basic concept of
radiation protection which specifies that exposure to ionizing radiation
and releases of radioactive materials should be managed to reduce
collective doses as far below regulatory limits as is reasonably
achievable considering economic, technological, and societal factors,
among others.
A positively charged particle emitted by some radioactive materials
undergoing radioactive decay. A helium nucleus (two protons and
two neutrons)
An underground geological formation, or group of formations,
containing water. Sources of groundwater for wells and springs.
Radiation from cosmic sources, naturally occurring radioactive
material, including radon (except as a decay product of source or
special nuclear material), and global fallout as it exists in the
environment from the testing of nuclear explosive devices or from
nuclear accidents like Chernobyl which contribute to background
radiation and are not under the control of the cognizant organization.
The International System (SI) unit of activity equal to one nuclear
transformation (disintegration) per second. 1 Bq = 2.7xl0"n Curies (Ci)
= 27.03 picocuries (pCi).
Berm	A horizontal shelf or ledge built into the embankment or sloping wall of
an open pit, quarry, or ground surface to break the continuity of an
otherwise long slope and to strengthen its stability or to catch and arrest
slide material.
Beta Particle	An electron emitted from an atom's nucleus during radioactive decay.
AI-4

-------
Beneficiated	The initial attempt at liberating and concentrating a valuable mineral
from extracted ore. This is typically performed by employing various
crushing, grinding and froth flotation techniques. The remaining
(beneficiated) material is often physically and chemically similar to the
material (ore or mineral) that entered the operation, except that particle
size reduction has often occurred.
Bioremediation	The use of biological agents, such as bacteria or plants, to remove or
neutralize contaminants, as in polluted soil or water.
A radioactive uranium bearing mineral, (U,Ca,Y,Ce)(Ti,Fe)206
A coarse-grained clastic rock, composed of angular broken rock
fragments held together by a mineral cement or in a fine-grained matrix.
Breccia may originate as a result of talus accumulation, explosive
igneous processes, collapse of rock material, or faulting.
Brannerite
Breccia
Byproduct
Materials	Tailings or wastes produced by the extraction or concentration of
uranium or thorium from any ore processed primarily for its source
material content, including discrete surface wastes resulting from
uranium solution extraction processes. Underground ore bodies depleted
by such solution extraction operations do not constitute "byproduct
material" within this definition.
Carbonates
Cleanup
Coffinite
Consolidated
Contamination
A sediment or sedimentary rock formed by the organic or inorganic
precipitation from aqueous solution of carbonates of calcium,
magnesium, or iron; e.g., limestone and dolomite.
Actions taken to deal with a release or threatened release of hazardous
substances that could affect public health or the environment. The term
is often used broadly to describe various Superfund response actions or
phases of remedial responses, such as remedial investigation/feasibility
study. Cleanup is sometimes used interchangeably with the terms
remedial action, response action, or corrective action.
A naturally occurring uranium mineral, U(Si04)i_x(0H)4x
In geology, any or all of the processes whereby loose, soft, or liquid
earth materials become firm and coherent, either cemented or non-
cemented together.
The presence of residual radioactivity, heavy metals or other pollutants
in excess of levels which are acceptable for release of a site or facility
for unrestricted use.
Core Sample	A soil, rock, or sediment sample taken by core drilling.
Conventional Mining Mining which uses either mechanical open-pit surface mining methods,
or underground mining methods, or a combination of both, to extract ore
AI-5

-------
from the ground. This is opposed to unconventional or solution mining
methods.
Curie (Ci)
The customary unit of radioactivity. One curie (Ci) is equal to 37 billion
disintegrations per second (3.7 x 1010 dps = 3.7 x 101CI Bq), which is
approximately equal to the decay rate of one gram of Ra-226. Fractions
of a curie, e.g. picocuries (pCi) or 10"12 Ci and microcurie (jxCi) or 10"6
Ci, are levels typically encountered in radiation measurements of NORM
or TENORM.
Decline
Decommission
A downward ramp.
To remove a facility or site safely from service and reduce residual
radioactivity to a level that permits release of the property and
termination of a source materials license and other authorization for site
operation.
Decommissioning
The process of removing a facility or site from operation, followed by
decontamination, and license termination (or termination of authorization
for operation) if appropriate. The objective of decommissioning is to
reduce the residual radioactivity in structures, materials, soils,
groundwater, and other media at the site so that the concentration of each
radionuclide contaminant that contributes to residual radioactivity is
indistinguishable from the background radiation concentration for that
radionuclide.
Drill Cuttings
Drilling Wastes
Dose
Electrodialysis
Elution
Evaporative Ponds
The particles of rock produced in a borehole or drill hole by the abrasive
or percussive action of a drill bit; erosive effect of the circulating liquid;
or cavings from the borehole. At some mines and operations sites, cores
of rock from a well or borehole may be left behind as waste—referred to
in this report as drill cuttings for convenience.
Wastes associated with a drillhole operation at a mine or extraction
facility that are not considered cuttings or cores. May include drill muds
or other drilling fluids, sludges, or evaporation products collected in
excavated pits from waste water produced during drilling.
A general term used to refer to the effect on a material that is exposed to
radiation. It is used to refer either to the amount of energy absorbed by a
material exposed to radiation, or to the potential biological effect in
tissue exposed to radiation
A means of extracting one or more dissolved materials from a liquid
mixture, the process is dialysis assisted by the application of an electric
potential across a semi-permeable membrane.
Process of removing an economic mineral (uranium) from an ion
exchange filter or resin.
Areas where mine water or other produced water is placed and dried by
evaporation, leaving a residue of solids or sludges.
AI-6

-------
Evaporite
An inorganic chemical sediment that precipitates when the salty water in
which it had dissolved evaporates.
Excavated Wall
A wall of mineral ore that has been exposed by mining over a
considerable width at one time.
Exposure Pathway The route by which radioactivity travels through the environment to
eventually cause radiation exposure to a person or group (e.g., air or
water). Also, the route by which a member of the public is exposed (e.g.,
ingestion, inhalation).
External Radiation Radiation from a source outside the body.
Extraction Facility An industrial complex and land on which are located buildings, wells and
pipelines, mechanical and chemical equipment, storage and
transportation equipment licensed by the Nuclear Regulatory
Commission or its Agreement States for the purposes of extracting
uranium (source material) in accordance with the Atomic Energy Act.
Extraction Process A process used to extract uranium from ore, either by milling and
chemically treating the ore, or using chemical solutions to treat
underground ore {in situ leaching), or by treating mined and crushed ore
on the surface (heap leaching). These processes are licensed activities by
the Nuclear Regulatory Commission or its Agreement States in
accordance with the Atomic Energy Act.
Gamma Radiation Penetrating high-energy, short-wavelength electromagnetic radiation
(similar to X-rays) emitted during radioactive decay. Gamma rays are
very penetrating and require dense materials (such as lead or steel) for
shielding.
Gangue
Garnet
Half-Life (t1/2)
Heap-Leaching
The valueless minerals in an ore; that part of an ore that is not
economically desirable but cannot be avoided in mining. It is separated
from the ore minerals during concentration.
A group of silicate minerals found in igneous rocks, usually red in color,
used as a semi-precious stone in crystalline form, or ground into smaller
particles and used for abrasives such as in sandpaper coating.
The time required for one-half of the atoms of a particular radionuclide
present to disintegrate.
A method of extraction by which mineral bearing ores are leached on the
ground surface from weathered low-grade ore. The crushed material is
laid on a slightly sloping, impervious pad and uniformly leached by the
percolation of leach liquor trickling through the beds by gravity to ponds.
The metals are recovered by conventional methods from the solution.
AI-7

-------
Igneous
Rock or mineral that solidified from molten or partly molten material,
i.e., lava or magma. These rocks constitute one of the three main classes
into which all rocks are divided: igneous, metamorphic, and sedimentary.
Ilmenite
An iron-black, opaque mineral (FETi03) which is the principal ore of
titanium.
Incline	A slanting shaft from the surface into an underground mine. Most
commonly referring to an upward slope.
In Situ Leaching (ISL) A method of extraction by which mineral bearing ores are leached
underground by the introduction of a solvent solution, called a lixiviant,
through injection wells drilled into the ore body. The process does not
require the extraction of ore from the ground. The lixiviant is injected,
passes through the ore body, and mobilizes the mineral, and the mineral-
bearing solution is pumped to the surface from production wells. The
pregnant leach solution is processed to extract the mineral sought after.
Ion Exchange
A common water-softening method often found on a large scale at water
purification plants that remove some organics and radium by adding
calcium oxide or calcium hydroxide to increase the pH to a level where
the metals will precipitate out.
Lab Waste
Wastes of any kind generated by a laboratory, usually on-site, analyzing
rock, sediment, water or other samples obtained at the mine or extraction
facility, or its vicinity.
Leachate
A solution obtained by leaching; e.g., water that has percolated through
soil containing soluble substances and that contains certain amounts of
these substances in solution.
Leach Liquor
Leuxocene
Lithologic
Lixiviant which contains minerals dissolved from host rocks.
General term for a fine-grained, opaque, whitish alteration (weathering)
product of ilmenite in mineral form.
Character of a rock described in terms of its structure, color, mineral
composition, grain size, and arrangement of its component parts; all
those visible features that in the aggregate impart individuality to the
rock. Lithology is the basis of correlation in coal mines and commonly is
reliable over a distance of a few miles.
Longwall Retreat A method of mining flat-bedded deposits, in which the working face is
mined over a considerable width at one time. The excavation retreats
towards the shaft. In this method, all the roadways are in the ore body
and the waste areas are left behind.
Lixiviant	A liquid medium that selectively extracts the desired metal from the ore
or material to be leached rapidly and completely, and from which the
desired metal can then be recovered in a concentrated form.
AI-8

-------
Mill Tailings
Residue of raw material or waste separated out during the processing of
uranium mineral ores. Byproduct material in accordance with the AEA.
Mine
Mining is the mechanical process by which mineral ores are extracted
from the earth.
Mine Footprint
Mineral Sands
NORM
The areal extent of land physically disrupted by a mine operation.
Eroded and generally unconsolidated sedimentary particles of rock
minerals of sand size which have accumulated in a geologic deposit, and
may be exploited or concentrated for economic purposes.
Naturally Occurring Radioactive Materials. Materials which may contain
any of the primordial radionuclides or radioactive elements as they occur
in nature, such as radium, uranium, thorium, potassium, and their
radioactive decay products, that are undisturbed as a result of human
activities.
Ore
Overburden
Permeable Reactive
Barrier
Pillar
Pit Lake
The naturally occurring material from which a mineral or minerals of
economic value can be extracted profitably or to satisfy social or political
objectives. The term is generally but not always used to refer to
metalliferous material, and is often modified by the names of the
valuable constituent; e.g., iron ore; ore mineral.
Designates material of any nature, consolidated or unconsolidated, that
overlies a deposit of useful materials or ores, especially those deposits
that are mined from the surface by open cuts or open-pit methods.
An emplacement of reactive materials in the subsurface designed to
intercept a contaminant plume, provide a preferential flow path through
the reactive media, and transform the contaminant(s) into
environmentally acceptable forms to attain remediation concentration
goals at points of compliance.
A column of ore left to support the overlying strata or hanging wall in a
mine, generally resulting in a "room and pillar" array. Pillars are
normally left permanently to support the surface or to keep old workings
water tight.
A lake which has formed by accumulation of water in an open-pit mine
excavation.
Pit Lake Water
Protore
Water which has filled an open-pit mine excavation, usually derived as
water from underground workings of the mine.
Mineral bearing rock that cannot be further processed at a profit under
existing conditions but that may become profitable with technological
advances or price increases.
AI-9

-------
Pseudomorph	A mineral whose outward crystal form is that of, or which resembles
another mineral species: it has developed by alteration, substitution,
incrustation, or other mineral process.
Radiation Survey Measurements of radiation levels associated with a site together (or
Radiological	with appropriate documentation and data evaluation.
Survey)
Radioactivity	The mean number of nuclear transformations occurring in a given
quantity of radioactive material per unit time. The International
System (SI) unit of radioactivity is the Becquerel (Bq). The
customary unit is the Curie (Ci).
Radioactive Decay The spontaneous transformation of an unstable atom into one or more
different nuclides accompanied by either the emission of energy and/or
particles from the nucleus, nuclear capture or ejection of orbital
electrons, or fission. Unstable atoms decay into a more stable state,
eventually reaching a form that does not decay further or has a very
long half-life.
Radionuclide
Reclamation
Reductant
or Reduction
Regulation
Rem
An unstable nuclide that undergoes radioactive decay.
Restoration of mined land to original contour, use or condition.
The addition of hydrogen, removal of oxygen, or addition of electrons to
an element or compound.
A rule, law, order, or direction from federal, state, or Tribal governments
regulating action or conduct. Regulations concerning radionuclides in the
environment in the United States are shared by the Environmental
Protection Agency (EPA), the U.S. Nuclear Regulatory Commission
(NRC), the U.S. Department of Energy (DOE), state and Tribal
governments.
Radiation Equivalent in Man. The conventional unit of dose equivalent.
The corresponding International System (SI) unit is Sievert (Sv): 1 Sv =
100 rem.
Remediation	Cleanup or other methods used to remove or contain a toxic spill or
hazardous materials from a Superfund site, or uranium mine or extraction
facility, including those included under the Uranium Mill Tailings
Radiation Control Act (UMTRCA).
AI-10

-------
Refuse	Solid waste. Non-liquid, non-soluble materials ranging from municipal
garbage to industrial wastes that contain complex and sometimes
hazardous substances. Solid wastes also include sewage sludge,
agricultural refuse, demolition wastes, mining equipment and mining
residues. Technically, solid waste also refers to liquids and gases in
containers.
Removal
Rill
Risk Assessment
Room and Pillar
Rutile
Saturated Zone
Scanning
The cleanup or removal of released hazardous substances, or pollutants
or contaminants which may present an imminent and substantial danger;
such actions as may be necessary taken in the event of the threat of
release of hazardous substances into the environment; such actions as
may be necessary to monitor, assess, and evaluate the threat of release of
hazardous substances; the removal and disposal of material, or the taking
of other such actions as may be necessary to prevent, minimize or
mitigate damage to the public health or welfare or the environment.
A small channel, as one formed by erosion.
Qualitative and quantitative evaluation of the risk posed to human health
and/or the environment by the actual or potential presence and/or use of
specific pollutants.
A conventional method of underground mining in which natural pillars
are left unmined for support between the mined rooms.
A usually reddish-brown mineral (Ti02) that is an ore of titanium.
A subsurface zone of soil or rock in which all the pore spaces are filled
with water under pressure greater than that of the atmosphere. This zone
is separated from the zone of aeration (above) by the water table.
An evaluation technique performed by moving a detection device over
a surface at a specified speed and distance above the surface to detect
radiation.
Secular Equilibrium A state of parent-daughter equilibrium that is achieved when the half-
life of the parent radionuclide is much longer than the half-life of the
daughter radionuclide decay product. In this case, if the two are not
separated, the daughter will eventually decay at the same rate at which
it is being produced. At this point, both parent and daughter will decay
at the same rate until the parent is essentially exhausted.
Sievert (Sv)	The special name for the International System (SI) unit of dose
equivalent. 1 Sv = 100 rem = 1 Joule per kilogram.
Site	Any mine or extraction facility installation, or discrete, physically
separate parcel of land or lands disturbed by mining or uranium
extraction, or any building or structure or portion thereof.
Soils	All unconsolidated materials above bedrock.
AI-11

-------
Solution Process	A method of extracting sought-after underground elements or minerals
from in-place ore, or elements or minerals from ore previously mined
and crushed. This is accomplished through the use of fluids which
dissolve the mineral from the rock, putting it into liquid solution which is
then processed or evaporated to obtain the desired element or mineral.
Solvent Extraction A process for extracting a mineral or element (e.g., uranium) from ore by
soaking rock with a (solvent) that dissolves the target element from the
rock and putting it into liquid solution. The liquid is then processed or
evaporated to obtain the desired element.
Source Materials	Uranium or thorium, or any combination thereof, in any physical or
chemical form or (2) ores which contain by weight one-twentieth of one
percent (0.05%) or more of: (i) Uranium, (ii) thorium or (iii) any
combination thereof. Source material does not include special nuclear
material, chemical
Special Nuclear
Material
Plutonium, U-233, and Uranium enriched in U-235, material capable of
undergoing a fission reaction.
Stewardship
Institutional controls (private or publicownership or governmental)
which may be put in place to ensure that a specific site meets its closure
goals. Institutional controls can be either active, involving some form of
continuous or intermittent human activity to maintain the condition of the
site, or passive, which do not require human intervention and have an
amount of redundancy built into them to deter or prevent disturbance of
the closed site.
Stope	An excavation from which ore has been removed in a series of steps. A
variation of step. Usually applied to highly inclined or vertical veins or
beds.
Survey	A systematic evaluation and documentation of radiological
measurements with a correctly calibrated instrument or instruments that
meet the sensitivity required by the objective of the evaluation.
Survey Plan	A plan for determining the radiological and other characteristics of a site.
TENORM	Acronym for Technologically Enhanced Naturally Occurring
Radioactive Material. Naturally occurring radioactive materials that have
been concentrated or exposed to the accessible environment as a result of
human activities such as manufacturing, mineral extraction, or water
processing.
Underground Injection The method by which fluids are placed under pressure in a well such that
the fluid enters an underground rock formation. A means by which ISL
wells inject lixiviant to dissolve uranium from underground ore bodies.
Unconsolidated	Rocks consisting of loosely coherent or uncemented particles, whether
occurring at the surface or at depth.
AI-12

-------
Underflow
Flowing bottom waters containing dissolved or suspended solids.
Unsaturated zone
Uprate
Volcaniclastic
Waste Rock
Wastewater
Working Level
The zone in which the pore opening of the functional permeable rocks
are not (except temporarily) filled with water under hydrostatic pressure;
the interstices are either not filled with water or are filled with water that
is held by capillarity.
The process of increasing the maximum power level at which a
commercial nuclear power plant may operate.
A sedimentary rock containing volcanic material without regard to its
origin or environment of deposition.
Rock void of uranium ore which may have been set aside as waste after
removal of top-soil, overburden and uranium ore or veins. Waste rock is
defined as barren or submarginal rock or ore that has been mined, but is
not of sufficient value to warrant treatment and is therefore removed
ahead of the milling processes.
The spent or used water from a mine that contains dissolved or
suspended matter.
A special unit of radon exposure defined as any combination of short-
lived radon daughters in 1 liter of air that will result in the ultimate
5
emission of 1.3x10 MeV of potential alpha energy. This value is
approximately equal to the alpha energy released from the decay of
progeny in equilibrium with 100 pCi of Ra-222.
AI-13

-------
Appendix II. Uranium Decay Series
In the figures below, Figure AII.l. for the uranium-238 radioactive decay series, and Figure All.2. for the
uranium-23 radioactive decay series, each radioactive element is shown in a box with its mass number
(226Ra for example) along with its half life in (^seconds (|iscc). minutes (m), days (d), and years (y). The
principal type of radiation given off as the radionuclide decays is shown alongside the box: alpha (a),
beta ((3).
Figure AII.l. Uranium-238 Radioactive Decay Series
2§8 pjj
5.® d
r 4 Th
24 d
2,4 Pa
1.2 m
214
27 m
240.000 y
234
210
Th
218
3.1 m
214
20 m
AII-1

-------
Figure AII.2. Uranium-235 (Actinium) Decay Series
235 U
231 Pa
4.000 y
231 Th
227 Th
16
22 y
1.2%
223 Ra
12 d
223 Fr
21 m
219 Rn
3.9
CL
215 Po
211 Po
1.8 ms
0.52 S
211 Bi
a
2.2 m
211 Ft p
36 m
207 Pb
STABLE
207 Tl
4.8 m
AII-2

-------
Appendix III. Overview of Uranium Mines
and In Situ Leach Operations Case Studies
In the main body of this report, mention is made of a number of conventional uranium mines and ISL
leach operations which were studied in detail by EPA in order to better understand the environmental
conditions associated uranium extraction. Portions, though not all, of the data collected in the course of
those studies were included in the report in order to illustrate points made in the text. The conventional
mine sites listed in this appendix are abandoned, idle, or in reclamation status, and the descriptions which
follow provide information on their location, size, and production status. ISL sites described were
licensed facilities under the environmental oversight of and regulation of the NRC or its Agreement
States. The wastes from those facilities are considered byproduct materials and not TENORM. As such,
the information presented in this Appendix is for information purposes only. For a description of how
new ISL operations are carried out, see Chapter 2.
A decision will be made in the near future about whether or not more detailed information on the
conventional mine and ISL sites which was assembled as case studies for this report will be issued
separately.
Canyonlands Uranium Mines. Lathrop Canyon. Utah
This is a group of 12 abandoned mines in sandstone deposits of southeastern Utah in a semi-arid region of
the country. The mines are remotely located in Lathrop Canyon of the Canyonlands National Park near
Moab, Utah, about 1V2 hour hike from the nearest visitor's center at the park. Mine waste rock is found in
piles inside and outside the mines, with contaminated water located below the mines. Contaminated water
does not directly feed into any major bodies of water. Total waste amounts are estimated at 1,750 m3
(2,322 yd3). A study done by Burghardt et al. (2000) provides most of the data on the site contamination.
Data are available on metals concentrations, pH, radiation levels, and electrical conductivity for the waste
rock piles. Similar information is available for the Lathrop Canyon water and drainage. Based on this
information, as well as population proximity information, the National Park Service and Utah Abandoned
Mine Lands Reclamation Program maintain that Lathrop Canyon Mines now pose minimal risk to human
safety and health.
Orphan Uranium Mine. Arizona
The Orphan Uranium mine is located at the Grand Canyon National Park in northern Arizona and is being
assessed by the National Park Service for cleanup under CERCLA. The deposit is in sandstone and
claystone, but occurs as a breccia pipe deposit. The mine's buildings, hoisting headframe, and ore loadout
area are located a short walk from the south rim visitor's center, although the area has been fenced to deter
visitors. Mining activities were conducted mainly between 1956 and 1969 for uranium, copper, silver, and
vanadium. Radioactive rock and soil have been found at the loading area, and at the mine itself, which is
located below the canyon rim. The mine still contains significant amounts of unmined uranium. Horn
Creek, which lies beneath the Orphan Mine and along a major hiking trail of the park was found to
discharge "hostile" effluent containing uranium and exceeding the maximum contaminant level for gross
alpha radiation in drinking water. Uranium contamination of Horn Creek may be derived from: surface
runoff from the upper mine site and tailing debris at the lower mine site; groundwater and surface water
AIII-1

-------
that have percolated through the Orphan Mine, including the open glory hole; and ore and waste rock
debris containing uranium that has eroded and has been swept into the drainage basin of Horn Creek. The
case study includes results of Horn Spring sampling for uranium, as well as radiation levels recorded for
the upper and lower mine sites. Approximately two million people visit the vicinity of the mine annually;
however, relatively few individuals are directly exposed to radiation.
Further evaluation of the site in accordance with CERCLA is underway to evaluate the extent of
contamination and cleanup alternatives. According to the National Park Service (U.S. NPS 2006), an
Engineering Evaluation/Cost Analysis (EE/CA) should commence for the upper mine area in 2006. This
study would analyze cleanup action and the effectiveness, feasibility, and cost of a number of cleanup
alternatives. Upon completion, the EE/CA (including any recommended cleanup) and supporting
documents would be made available to the public for review and comment. An EE/CA for the lower and
middle mine areas was also being planned.
Midnite Uranium Mine. Washington
The Midnite Mine is an inactive open-pit uranium mine located within the boundaries of the Spokane
Indian Reservation in eastern Washington State, and is a disseminated deposit in igneous rocks. It was
operated by Dawn Mining Company between 1955 and 1981, and the disturbed area covers
approximately 320 acres (129.6 hectares). The initial series of open-pits were backfilled with waste rock
as mining progressed, and additional overburden and waste rock is on the surface, as well as a number of
ore/protore stockpiles. Two large pits remain open and accumulate water from multiple sources, including
seep water collected at the base of the largest waste rock pile. The pile was graded and partly reclaimed
by the mining company, which also operates an ongoing seep collection system and BaCl2 treatment
facility. Midnite Mine was listed as a Superfund site in 2000, and an EPA-funded study is under way. In
addition to the seeps and impounded surface water contaminated with heavy metals and radionuclides,
contamination has spread to areas outside the mined area in surface water and sediments, groundwater,
and road dust. Most runoff from the mined area flows to three streams (called "drainages"). The drainages
meet south of the mine and flow into Blue Creek. Blue Creek travels an additional 3.5 miles to the
Spokane River Arm of Lake Roosevelt. Shallow groundwater also flows from the mined area along the
three drainages and emerges south of the mined area. Collection and treatment of contaminated water has
reduced the amount of contamination entering surface water. However, the drainages and Blue Creek still
show ongoing contamination from the mine. A proposed cleanup plan was issued by EPA in September
of2005.
Bluewater Uranium Mines. New Mexico
The Bluewater Uranium mines are a series of three sandstone mine sites located in north Central Cibola
County in west-central New Mexico. Portions of the site had a semi-agricultural rural setting where
approximately 65 persons lived in 1990. The mines were operated primarily between 1952 and 1966.
Reclamation activities were conducted by EPA, ATSDR, and the Navajo Superfund Program to reduce
potential radiological hazards associated with the mines. As a result of previous mining activities and the
absence of reclamation action, the sites contained large open-pits with exposed uranium-bearing
overburden, waste rock, and protore. A contaminated water well and houses constructed with uranium
mine wastes were closed and removed. Radiological contaminants of concern were uranium and its
AIII-2

-------
daughter products of radium, thorium, bismuth, lead, and radon gas. Heavy metal species suspected to be
present in the mining waste were arsenic, barium, manganese, molybdenum, selenium, strontium, and
vanadium, Analytical data on uranium and radium were collected prior to and after the completion of
reclamation activities.
White King/Lucky Lass Uranium Mine Sites. Oregon
Also known as the Fremont National Forest Superfund Site, the site is located in south-central Oregon,
and includes two former uranium mining areas encompassing about 140 acres (about 57 hectares). The
site is located in a mountainous semi-arid setting on National Forest Service lands, with the closest
residences and drinking water wells more than 10 miles (16 kilometers) from the site. The mines are
located within the northwest terminus of the Basin and Range province. This area is characterized by
north-trending fault-block mountains and basins of internal drainage. Geologic units in the region are
characterized by a thick sequence of volcanic flows and volcaniclastic rocks which have been extensively
faulted and fractured. The major features include a water-filled excavation pit (pond); a protore stockpile;
an overburden stockpile; areas where overburden and ore were dumped or spilled; and Augur Creek,
which flows adjacent to the two White King stockpiles. Mining operations were conducted between 1955
and 1965, with exploratory drilling conducted until 1979. The area has been extensively sampled for
arsenic, uranium-234/238, radium, and radon. A baseline risk assessment was conducted and serves as
part of the record of decision (ROD). Construction for remediation of the sites began in 2005.
Yazzie—312 Mine. Cameron. Arizona
The Yazzie-312 Uranium Mine is located on the Navajo Indian Reservation located in the Painted Desert
section of the Black Mesa basin area near Cameron, Arizona. The site was operated between 1956 and
1961 and contained a large, water-filled open-pit lake; the water had been used for recreational swimming
and livestock watering. The water standing in the Yazzie-312 pit was the result of an artesian flow from
an underlying aquifer. The mine was in the Petrified Forest Member of the Chinle Formation. The mine
operator drilled a hole in the bottom of the pit looking for a deeper ore horizon. The drill hole
encountered artesian water in the Shinarump Member, which filled the pit.
The EPA studied the mine to determine: the presence of metals and radionuclides in water within the
mine pit, in underlying water, and in the Little Colorado River; assessing metals and radionuclides in
subsurface soil and sediments; determining infiltration in the water-filled mine pit; and assessing
communication into other aquifers at the site. Analytical data were collected on several borings for soil
samples, as well as several water samples. The area has several hard impermeable substrates located
between 50 and 130 feet (15.2 and 39.6 meters) below ground surface. Elevated levels of uranium and
thorium were found at soil depths that were above the groundwater table (110 to 210 feet) (33.5 to 64
meters-below ground surface), with significantly lower levels found at deeper depths. No metal levels
exceeded EPA Region 9's Preliminary Remediation Goals. In the overburden and protore piles, the most
significant contaminants were the uranium and thorium concentrations. Groundwater samples indicated
contamination for uranium, radium, arsenic, beryllium, chromium, and manganese. Pit water tested
similarly high for the same contaminants and for iron and lead. Testing also indicated that the Little
Colorado River contained measureable uranium, arsenic, beryllium, and chromium, although not at
significant levels. The mine site was remediated by the Navajo Abandoned Mine Land agency in 2002.
AIII-3

-------
Uranium In Situ Fields
Crow Butte. Nebraska
Cameco's facility and associated wellfields are located in west-central Dawes County, Nebraska, just
north of the Pine Ridge, five miles southeast of Crawford, Nebraska. The total surface area of the project
site is approximately 2,800 acres (1,134 hectares), with about 500 acres (202 hectares) that will be
disturbed during the life of the project. The uranium deposit at the Crow Butte site is a roll-front deposit,
similar to those in the Wyoming basins. Liquid wastes from operations are generated from three sources:
(1) wellfield development, (2) processing plant operations, and (3) aquifer restoration activities.
Currently, Cameco has three options approved by the NRC for the disposal of liquid wastes: (1) solar
evaporation ponds, (2) land application, or (3) deep-well injection. At this time, land application has not
been used. The study contains results for lead, polonium, radium, radon, thorium, and uranium, taken
from both the ponds located at the site and surface waters.
Holidav/El Mesauite. Texas
The Combined Holiday and El Mesquite ISL fields are located in Duval and Webb counties, Texas, and
they cover a permit area of approximately 4,500 acres (1,822 hectares). They are owned by COGEMA
which cited its total wellfield area as 335 acres (135 hectares) in two combined leases, with 1,750
injection wells and 1,450 production wells. Production commenced in 1977, with the expectation of 17
years of production and the fields' producing an ore grade of 0.07% using a sodium bicarbonate-injected
lixiviant. Production from the fields averaged 750 tons of uranium per year, with an estimated extraction
efficiency of 93 to 95%. Wastewater was collected at two storage ponds at the El Mesquite project before
injection into deep disposal wells. The El Mesquite project lease area comprises 2,900 acres (1174
hectares) including five wellfields, three satellite locations, a processing plant, a yellowcake dryer,
administrative buildings, a laboratory, a warehouse, and a maintenance shop. The Holiday lease covers
1,483 acres (600 hectares), including 10 wellfields and two satellite locations. Uranium production at the
Holiday and El Mesquite project areas has ceased, and negative pressure in producing wells of the field is
maintained to prevent excursions of pollutants (or plume migration) beyond mine lease boundaries. Areas
that were depleted at an early point in the operations history were subjects of groundwater restoration
activities. At Holiday and El Mesquite, the groundwater prior to extraction was usable for livestock
watering, (with some localized exceptions, due to elevated radium-226, which is present in the
groundwater within the uranium ore body). Therefore, COGEMA's goal after extraction is to clean up the
groundwater to as close to background conditions as possible.
AIII-4

-------
Irigaray and Christensen Ranch. Wyoming
The Irigaray and Christensen Ranch projects are two separate ISL operations that are located about 51 to
55 miles (82 to 88 kilometers) southeast of Buffalo in the Powder River Basin in northeast Wyoming. The
Irigaray property is 21,100 acres (8,545 hectares) and contains the central plant for both projects, though
the actual disturbed area for Irigaray is only 133 acres. COGEMA purchased both properties in April
1993, and all mining activities (at both sites) ceased in June 2000. The ore mineralization is one of many
roll-front type uranium deposits located in the Wasatch formation. Water treatment processes, such as
reverse osmosis, were used to clean wellfield bleed water for use in restoration. Uranium-laden resin from
the ion exchange columns was transferred to a tanker trailer and trucked to the Irigaray central plant for
elution, final uranium precipitation, and drying. Wastewater disposal capability included evaporation in
lined ponds, storage of clean water (reverse osmosis permeate) in clay-lined ponds, treatment and disposal
via surface discharge under a Wyoming National Pollutant Discharge Elimination System permit, and
deep-well injection. The lined solar evaporation ponds were initially designed to provide a surface area
and capacity capable of evaporating a 5 gallons per minute (about 19 liters per minute) process effluent
stream. The four lined solar evaporation ponds were designed to meet the requirements of the NRC.
Samples of the wastewater effluents were taken and tested for uranium and radium concentrations.
Restoration of the Irigaray well fields was complete in August 2002 and was expected to be complete at
Christensen Ranch in 2006. Surface decommissioning and reclamation are underway (as approved by
NRC) and should be complete in 2007.
Crownpoint Uranium. New Mexico
The proposed Crownpoint Uranium ISL project consists of three properties located near Church Rock,
New Mexico. Operations at the Crownpoint site would include a central processing facility where
yellowcake will be dried and packaged. Generally, the uranium deposits are a few feet thick and several
hundred to a thousand feet (305 meters) long, and may be stacked, usually parallel to the strike of the host
rock. Uranium was proposed to be extracted from the ore bodies by leachate mining, using a sodium
bicarbonate lixiviant, and is then extracted from the solution and concentrated. Uranium to be produced at
the Church Rock and Unit 1 sites, uranium concentrate, in the form of either uranium-loaded resin beads
or yellowcake slurry, would be shipped by truck to the central processing facility and packaged into a
final yellowcake product. Before the waste would be disposed of, barium chloride would be added to
effectively remove radium, thus lowering the radionuclide concentrations of the waste. HRI, the site's
owner and operator, is currently considering up to five different final disposal options for wastewaters
(both process-generated and restoration waters): (1) surface discharge, (2) land application, (3) brine
concentration, (4) waste-retention ponds, and (5) deep-well disposal. At present, HRI is limited to using
surface discharge (with appropriate state or federal permits/licenses), brine concentration, waste-retention
ponds, or a combination of the three options to dispose of process wastewater. In July 2005, NRC
required that HRI reduce its secondary groundwater restoration standard for uranium from 0.44 mg/L to
0.03 mg/L.
AIII-5

-------
Highlands Uranium. Wyoming
Operated by Power Resources, Inc., Highlands is a 15,000-acre (6,073 hectare) ISL facility, located in the
Southern Powder River Basin of east-central Wyoming, in central Converse County, Wyoming. The land
has been used for seasonal sheep and cattle grazing. The uranium production process uses a lixiviant
comprised of native groundwater with gaseous carbon dioxide and oxygen, which is injected into the ore
zone through a series of well patterns. Uranium becomes dissolved within the lixiviant, which is pumped
from the ground, treated to remove the uranium, then re-injected into the ore zone. Liquid wastes from the
operation consist of two types of wastewater: (1) freshwater streams and (2) a saltwater stream. The
freshwater streams consist of restoration wastewaters and well field/process purge. Together, the process
purge and restoration fluids make up the irrigation water source. Power Resources disposes of its
freshwater waste stream by using radium settling basins, purge storage reservoirs, and irrigation areas.
Due to erosion problems encountered with the original clay liner of the ponds, a geotextile fabric was
installed in September 1988 to protect against future erosion concerns. Data was obtained for radium and
uranium in the settling ponds. Saltwater waste is disposed of in a waste disposal injection well. The
saltwater waste is produced from several sources in the uranium recovery and yellowcake production
process. The sources that make up this waste stream include analytical laboratory liquid wastes, elution
agents decanted from the precipitation circuit, yellowcake wash water, reject solutions from the water
treatment process, and washdown water from the Central Processing Facility.
Smith Ranch. Wyoming
This Power Resources project acquired from Rio Algom, is a 16,000-acre (6,480 hectare) site at the Smith
Ranch, located in the North Platte River drainage in Converse County, approximately 17 miles (27.2
kilometers) northeast of Glenrock, Wyoming. Power Resources proposed to extract uranium at depths of
450 to 1,000 feet (137 to 305 meters). The project involves approximately 25 individual mining units.
When the project was to be fully operational, about two years after licensing, approximately five mining
units would be in production at a time. Extraction would proceed approximately three years in each unit,
followed by an equivalent period of unit restoration and surveillance monitoring. The proposed schedule
covers a total of about 20 years. Liquid effluents from the operation include the production bleed stream,
excess fluids from the elution and precipitation process, regeneration of the water softener system
(calcium control), yellowcake rinse water, plant washdown water, restoration equipment waste,
restoration bleed, and facility sanitary waste. If the water quality was acceptable, the water would then be
routed through a separate radium removal and solids settling system prior to evaporation and/or land
application (surface irrigation). Excess liquids from the elution and precipitation circuit and water
softener regeneration were expected to average about 60 gallons per minute (227 liters per minute) and
would be routed to lined evaporation ponds or to a disposal injection well. In 2005, Power Resources
applied for an amendment to the Smith Ranch/Highland license to include the adjacent planned Reynolds
Ranch ISL project as a satellite facility. Sample data on radium and uranium concentrations in
evaporation ponds from the pilot projects were obtained by EPA.
AIII-6

-------
Appendix IV. Calculations of Volumes of Uranium Overburden
and Waste Rock
Conventional mining techniques produce large amounts of solid waste materials. Open-pit mining in
particular produces large quantities of overburden, while underground mining produces lesser, but still
significant amounts of waste rock. Overburden and weakly mineralized waste rock that have not been
used for reclamation have usually been stored in piles on site and are usually unsaturated, given that most
conventional mining occurs in arid regions (U.S. DOE/EIA 1997). In general in this Appendix
overburden and waste rock have been included together in estimating total waste rock at the mine sites.
The density of mine wastes varies, depending on the type of ore body with which they are associated and
the geology of the enclosing rock formations. Standard weight per volume figures used in mine waste
calculations are 1.68 tons/y3 or 2 MT/m3.
The approach used here is to estimate the ratio of waste rock production to ore production by mining
category (open-pit and underground); calculate the amount of waste generated from annual production
statistics (also given by mining category); and compare these numbers to waste volumes known or
calculated for various mines.
When the uranium mining industry first started, most of the ores were recovered from deposits located at
or near the surface. Ores were often exposed at the surface and shallow open-pit and underground mines
often followed mineralized zones directly into the subsurface. The open-pit mines would remove thin
overburden from buried parts of the ore body adjacent to the surface exposure. As easily accessible ore
deposits became depleted, mining had to be performed at increasing depths by either open-pit or
underground methods. In addition, lower grade ore deposits, once ignored, were later mined by using
improved mining methods and more efficient ore extraction techniques. In the early mining years, an ore
grade of 0.15% was often ignored; more recent mining practices target ore grades as low as 0.03%.
Accordingly, over the years, the mining industry was required to move larger quantities of topsoil,
overburden, and other waste rock in order to reach deeper deposits.
The amount of overburden that can be economically removed during open-pit mining is a complex
function of the depth to the orebody, the grade and thickness of the ore-bearing zone, the price of
uranium, and the costs of moving the overburden. The costs of processing ore at mills also influence the
economics. Those processing costs, which apply to both underground and surface mines, have steadily
declined and have lowered the ore grade that is economic to mine.
Information about the ratio of waste rock to ore can be derived from Abandoned Mine Land survey
reports written since the mid-1980s, production statistics in files of the U.S. Geological Survey, from
mining journal articles, from detailed descriptions of uranium mining operations in statewide
compilations, and from interviews with mining engineers at selected properties. Such data are available
for mines in Wyoming, Texas, Arizona, and New Mexico (Table AIV.l).
The ratio of waste rock to ore for mines of varying sizes shows that small open-pit mines are highly
variable, but the ratios for the largest mines (greater than 900,000 MTs of ore) tend to range from 8:1 to
20:1. For example, the largest open-pit mine in the United States, the Jackpile-Paguate mine in New
Mexico, was in the 12:1 range through the first 21 years of production (1953-73) but finished with an
overall 16:1 ratio before production ceased in early 1982. The nearby St. Anthony open-pit mine had a
stripping ratio of 10:1. The Shirley basin open-pit complex in Wyoming had an 8:1 waste to ore ratio.
AIV-1

-------
Open-pits in Texas seem to have variable waste to ore ratios ranging from 2:1 to 20:1 for the smaller
older pits on shallow ore bodies to relatively high values of 20:1 to 50:1 for the deeper deposits. Large
open-pits dominate production in Wyoming and New Mexico, whereas smaller open-pits occur in
Colorado, Utah, and Arizona. The Moonlight and Monument #2 open-pits in Arizona are thought to have
had a 5:1 stripping ratio based on the depth to ore and ore thickness (Chenoweth 1998). Smaller open-pit
operations in the range of 900 MTs to 900,000 MTs of ore have waste to ore ratios that generally range
from 10:1 to 30:1.
The Jackpile-Paguate open-pit mine began production in 1953. Between 1953 and early 1963, 70 MMTs
of overburden and associated waste and subore material had been removed to acquire 6.0 MMTs of ore (a
ratio of about 11.8:1, Kittel 1963). By mid-1974, about 110 MMTs of overburden were removed and 9
MMTs of ore were recovered at an average grade of 0.25% (a 12:1 ratio, Graves 1974). Production ceased
in early 1982, with a total of 364 MMTs of overburden and related materials removed from the ore body
and 23 MMTs of ore produced (U.S. BLM 1986), a ratio of 16:1. The mine site contained 32 waste
dumps and 23 protore dumps segregated according to grade. About 10.5 MMTs of protore were stored
outside of the pits, and another 4.5 MMTs in dumps within pits. The ratio of all waste to protore was
about 24:1. About 92 MMTs of backfill, comprised of ore-associated waste and some overburden, were
returned to the pits during operations.
Throughout the 1950s, 1960s, and 1970s, open-pit mining was characterized by numerous small to
moderate-sized open-pit operations with highly variable waste to ore ratios on the Colorado Plateau, by
large open-pit mines in Wyoming and New Mexico with variable but usually lower waste to ore ratios,
and by moderate to large open-pit operations in Texas with generally high waste to ore ratios. In the late
1970s and early 1980s waste to ore ratios for the largest mines appear to have peaked at an average of
about 30:1 (Bohert and Gerity 1978; Facer et al. 1978). As the price of uranium dropped in the early
1980s, only the more efficient open-pit operations remained in production and the waste to ore ratios
probably dropped significantly for the period 1984 to 1992.
Underground mining operations result in much smaller spoil storage piles than those generated by surface
mines. Consequently, the waste to ore ratio generally ranges from 20:1 to 1:1 for underground mines,
with an average ratio of about 9:1 (U.S. EPA 1983b). As with surface mining, this ratio has also increased
over the years from a range of 5:1 until the early 1970s to about 1:1 by the late 1970s.
AIV-2

-------
Table AIV.l Waste to Ore Relation for Mines in Texas, Wyoming, Arizona, and New Mexico
State
Waste in tons
Ore in tons
Ratio
TX
37,300,000
1,945,366
19.2

6,720,000
264,660
25.4

2,040,000
52,390
38.9

220,000
29,000
7.6

138,600
7,899
17.5

168,000
35,495
4.7

5,980,000
117,709
50.8

1,025,000
575,000
1.8

1,610,000
117,775
13.7

5,300,000
148,294
35.7
WY
121,106,000
14,687,480
8.2

405,350,000
10,350,000
39.2

69,050
10,900
6.3

28,900
2,347
12.3

25,200
1,000
25.2

29,700
4,343
6.8

7,728
201
38.4

59,500
1,761
33.8

15,900
256
62.1

34,340
259
132.6

6,540
67
97.6

30,100
153
196.7

42,700
54
790.7

21,190
11
1926.4

27,330
1,056
25.9

9,160
358
25.6

134,160
2,175
61.7

3,440
61
56.4

16,300
95
171.6

72,996
2,341
31.2

91,140
3,800
24.0

154,812
4,000
38.7

4,032
975
4.1

25,450
22
1156.8

10,350
63
164.3
AIV-3

-------
Table AIV.l Waste to Ore Relation for Mines in Texas,
Wyoming, Arizona, and New Mexico (cont.)
State
Waste in tons
Ore in tons
Ratio
WY (cont.)
20,160
62
325.2

7,190
7,130
1.0

18,600
134
138.8

37,800
1,270
29.8

16,180
284
57.0

22,390
1,345
16.6

7,140
462
15.5

18,300
1,471
12.4

46,940
485
96.8

3,090
387
8.0
AZ
758
3
252.7

42,000
926
45.4

202
7
28.8

3,920
109
36.0

61
6
10.1

55,200
1,363
40.5

706
123
5.7

12,440
586
21.2

4,200
305
13.8

15,750
794
19.8

958,220
33,821
28.3

7,390
563
13.1

226,800
1,264
179.4

294,000
1,128
260.6

19,320
218
88.6

14,950
1,042
14.3

2,100
23
91.3

196,560
2,829
69.5

22,340
343
65.1

31,080
1,610
19.3
NM
364,000,000
23,000,000
15.8

St. Anthony Pit

10.0

50,000
10,400
4.8
Sources: AVI 1986, HE 1987, RCT1994, Kittel 1963, SRB 1981, Chenoweth 1998, McLenore 1983, Finch 1998.
AIV-4

-------
Uranium ore production rates since 1948 for conventional mining techniques and related
production amounts of overburden are given in Table AIV.2. As shown in the table, the estimates
for surface mine ratios (overburden to ore) are based on a factor of 30 for the entire period. This
approach is believed to arrive at a total waste number for open-pit mines that seems reasonable (i.e.
should not significantly over- or underestimate the number), considering the waste volumes
associated with the largest mines (see discussion below).
For underground mines, a ratio of 3:1 was used for the years 1948-1970, and 1:1 was used for
1971 and later on. Despite the earlier EPA estimate mentioned previously, it is believed that
applying a single ratio of 9:1 for all years would significantly underestimate the amount of waste
generated during the last two decades.
Based on the preceding discussion, the total overburden produced by open-pit mines is estimated to
range from 1 billion metric tons to 8 billion metric tons, with an average of 3 billion metric tons.
For underground mines, the estimate ranges from 5 MMTs to 1 hundred MMTs, averaging 67
MMTs. Waste produced by open-pit mining is a factor of 45 greater than that for underground
mining, based on their respective averages. For the range between the low and high estimates, the
factor is 190 for the low estimate and 80 for the higher one. Thus, the amount of overburden
generated from open-pit mines far exceeds that from underground mines.
The four largest mines in Table AIV. 1 yield about 30% of the surface mine total; however, the size
of mines drops dramatically as the rest of the inventory is considered. More than 1,000 of the 1,300
surface mines that have been operated in the past 50 years have produced less than 900 MTs of ore.
These mines total less than 30 MMTs of waste, or less than 1% of the median estimate.
Accordingly, the waste inventory produced by this industry is primarily the result of past
operations at some 300 surface mines (SC&A 1989).
AIV-5

-------
Year
1948
1949
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
Table AIV.2. Uranium Ore Production Rates and Overburden 1948—1996
Ore (MTs)
Open-Pit Mining
Overburden (MTs)
Low
Avg.
High
Ore (MTs)
Underground Mining
Overburden (MTs)
Low
Avg.
<9.0E+02
9.1E+03
2.7E+04
7.3E+04
3.4E+04
1.7E+03
1.1E+04
9.1E+02
9.1E+03
2.7E+04
7.3E+04
1.6E+05
7.8E+03
5.2E+04
2.1E+04
2.1E+05
6.3E+05
1.7E+06
2.1E+05
1.0E+04
6.9E+04
2.5E+04
2.5E+05
7.6E+05
2.0E+06
2.9E+05
1.4E+04
9.6E+04
5.9E+04
5.9E+05
1.8E+06
4.7E+06
3.4E+05
1.7E+04
1.1E+05
1.6E+05
1.6E+06
4.9E+06
1.3E+07
5.0E+05
2.5E+04
1.7E+05
2.4E+05
2.4E+06
7.2E+06
1.9E+07
7.6E+05
3.8E+04
2.5E+05
3.4E+05
3.4E+06
1.0E+07
2.7E+07
1.0E+06
5.2E+04
3.5E+05
1.1E+06
1.1E+07
3.4E+07
9.1E+07
1.6E+06
8.0E+04
5.3E+05
1.5E+06
1.5E+07
4.4E+07
1.2E+08
1.9E+06
9.4E+04
6.3E+05
2.1E+06
2.1E+07
6.4E+07
1.7E+08
2.6E+06
1.3E+05
8.5E+05
2.0E+06
2.0E+07
6.0E+07
1.6E+08
4.3E+06
2.2E+05
1.4E+06
2.2E+06
2.2E+07
6.5E+07
1.7E+08
5.1E+06
2.5E+05
1.7E+06
2.3E+06
2.3E+07
6.8E+07
1.8E+08
5.0E+06
2.5E+05
1.7E+06
1.6E+06
1.6E+07
4.8E+07
1.3E+08
4.8E+06
2.4E+05
1.6E+06
1.7E+06
1.7E+07
5.1E+07
1.4E+08
3.7E+06
1.8E+05
1.2E+06
1.4E+06
1.4E+07
4.2E+07
1.1E+08
3.4E+06
1.7E+05
1.1E+06
1.1E+06
1.1E+07
3.4E+07
9.0E+07
2.8E+06
1.4E+05
9.5E+05
1.2E+06
1.2E+07
3.6E+07
9.7E+07
2.7E+06
1.4E+05
9.1E+05
1.4E+06
1.4E+07
4.3E+07
1.2E+08
3.4E+06
1.7E+05
1.1E+06
2.1E+06
2.1E+07
6.4E+07
1.7E+08
3.7E+06
1.9E+05
1.2E+06
2.0E+06
2.0E+07
5.9E+07
1.6E+08
3.4E+06
1.7E+05
1.1E+06
2.5E+06
2.5E+07
7.6E+07
2.0E+08
3.2E+06
1.6E+05
1.1E+06
3.0E+06
3.0E+07
8.9E+07
2.4E+08
2.7E+06
1.4E+05
2.7E+06
3.5E+06
3.5E+07
1.1E+08
2.8E+08
2.3E+06
1.1E+05
2.3E+06
4.1E+06
4.1E+07
1.2E+08
3.3E+08
1.8E+06
9.0E+04
1.8E+06
3.8E+06
3.8E+07
1.1E+08
3.1E+08
2.6E+06
1.3E+05
2.6E+06
3.9E+06
3.9E+07
1.2E+08
3.1E+08
2.5E+06
1.3E+05
2.5E+06
4.2E+06
4.2E+07
1.3E+08
3.4E+08
3.6E+06
1.8E+05
3.6E+06
5.1E+06
5.1E+07
1.5E+08
4.0E+08
4.3E+06
2.2E+05
4.3E+06
7.5E+06
7.5E+07
2.2E+08
6.0E+08
5.5E+06
2.8E+05
5.5E+06
8.8E+06
8.8E+07
2.6E+08
7.0E+08
4.9E+06
2.4E+05
4.9E+06
9.4E+06
9.4E+07
2.8E+08
7.5E+08
5.8E+06
2.9E+05
5.8E+06
7.7E+06
7.7E+07
2.3E+08
6.1E+08
4.7E+06
2.4E+05
4.7E+06
5.0E+06
5.0E+07
1.5E+08
4.0E+08
2.5E+06
1.3E+05
2.5E+06
4.4E+06
4.4E+07
1.3E+08
3.6E+08
2.3E+06
1.1E+05
2.3E+06
AIV-6

-------
Table AIV.2. Uranium Ore Production Rates and Overburden 1948—1996 (cont.)
Year
Open-Pit Mining
Underground Mining
Ore (MTs)
Overburden (MTs)
Ore (MTs)
Overburden (MTs)
Low
Avg.
High
Low
Avg.
High
1984
1.8E+06
1.8E+07
5.4E+07
1.4E+08
9.3E+05
4.7E+04
9.3E+05
9.3E+05
1985
8.5E+05
8.5E+06
2.5E+07
6.8E+07
5.2E+05
2.6E+04
5.2E+05
5.2E+05
1986
1.3E+05
1.3E+06
3.8E+06
1.0E+07
6.0E+05
3.0E+04
6.0E+05
6.0E+05
mr
1.7E+05
1.7E+06
5.1E+06
1.4E+06
7.8E+05
3.9E+04
4.6E+05
4.6E+05
1988"
6.5E+05
6.5E+06
2.0E+07
5.2E+07
8.5E+05
4.3E+04
4.7E+05
4.7E+05
1989a
6.2E+05
6.2E+06
1.9E+07
5.0E+07
7.3E+05
3.7E+04
7.3E+05
7.3E+05
1990a
2.9E+05
2.9E+06
8.7E+06
2.3E+07
2.8E+05
1.4E+04
2.8E+05
2.8E+05
1991"
6.0E+05
6.0E+06
1.8E+07
4.8E+07
6.0E+05
3.0E+04
6.0E+05
6.0E+05
1992
<9.0E+02
—
—
-
<9.0E+02
—
-
-
1993
none
-
-
-
none
-
-
-
1994
none
—
—
-
none
-
-
-
1995
none
-
-
-
none
-
-
-
1996
none
—
-
-
<9.0E+02
-
-
-
Total
1.03E+08
1.03E+09
3.08E+09
8.21E+09
1.06E+08
5.29E+06
6.91E+7
1.06E+08
1948-1987

1.0E+09
3.0E+09
8.0E+09

5.2E+06
6.7E+07
1.0E+08
1987-1996

2.3E+07
6.7E+07
1.7E+08

1.6E+05
2.5E+06
2.5E+06
" Ore volumes not reported by mining category; volumes based on annual average uranium content of ore.
AIV-7

-------
Appendix V. Radiochemical Data for Uranium Overburden and Waste Rock,
Pit Lakes and Streams, and In Situ Leach Operations
Introduction
The following tables present radionuclide concentration data on solid and liquid wastes at conventional
mines, pit lakes and streams, and from in situ leach operations. The data compiled has come from a wide
variety of sources, many or most without uncertainty limits on the data provided. However, the
information is instructive in providing a range of values for these wastes from numerous mines and
facilities throughout the west.
In several of the sources, measurements were reported for samples taken from conventional mine "waste"
or "spoils" or "dumps" without distinguishing between overburden, soil, or waste rock, or potentially
protore. Nevertheless, those studies provide a sense of how radioactive the wastes may be at those sites.
AV-1

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
AVI 1991
Avg. of 54
analyses
30.7
(1.14)
15.2
(0.56)


Bullrush spoils,
drill hole data
Range of 54
analyses
2-299
(0.07-3.7)
2-140
(0.07-5.18)


Whitworth 1996
Mine waste, avg.
24.4
(0.9)
28.2
(1.04)


La Bajada Mine,
NM
Pro tore, avg.
75
(2.78)
613.5
(2.28)


PEDCO 1983
Protore, NM
59
(2.18)
78.4
(0.259)


Protore
71.4
(2.64)
51.4
(1.9)


Protore
112
(4.14)
88.9
(3.29)


Protore
122
(4.51)
55.8
(2.06)


Protore
63.7
(2.36)
66.4
(2.46)


Waste
1.47
(0.05)
1.71
(0.06)


Waste
9.3
(0.34)
7.8
(0.29)


Waste
4.2
(0.16)
3.5
(0.13)


Waste
34.5
(12.77)
30
(1.11)


Protore, WY
8.55
(0.32)
37.4
(1.38)


Waste
17.6
(0.65)
1.17
(0.04)


Waste
1.35
(0.05)
10.8
(0.4)


Soil
0.51
(0.02)
0.71
(0.02)


Protore
129
(4.77)
82.2
(0.3)


Waste

1.23
(0.05)


Waste

0.81
(0.03)


Waste
0.61
(0.02)
3.2
(0.12)


Waste
1.17
(0.04)
1.06
(0.04)


Protore
54.4
(2.0)
67.9
(2.51)


AV-2

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
PEDCO 1983
(cont.)
Waste
0.93
(0.03)
2.15
(0.08)



Waste
0.18
(0.01)
2.74
(0.1)



Soil
1.55
(0.11)
1
(0.04)



Protore
97.1
(3.59)
148
(0.67)



Waste
7.1
(0.26)
5
(0.19)



Waste
4.9
(0.19)
6.3
(0.23)



Soil
4
(0.15)
3.9
(0.14)



Waste, jxg
26.4
32.4



Waste, |xg
5.8
6.1



Waste, |ig
15.7
11.6



Waste, |xg
24
16.4



Waste, jxg
58.3
31.9



Waste, |xg
58.7
39.4



Waste
6.2
(0.23)
4.4
(0.16)



Protore
137
(5.07)
118
(4.37)



Waste
30.5
(1.13)
25.8
0.95)



Protore
215
(7.96)
76.5
(2.83)



Waste
30.8
(1.14)
27.9
(1.03)



Waste
23.9
(0.88)
17.2
(0.04)



Waste, |xg
54.3
40



Waste, |xg
12.4
8


EPA 1983
Boulder sites


40-100


Uravan


50-220


S.M., waste


35-275


ore


100-350


overburden


20-120


below ground


10-13

AV-3

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
EPA 1983
(cont.)
Mesa Top, waste


25-290

Barb Jo, waste


2-170

Poison C.,waste


65-250

overburden


25-65

Morton R.,
protore


200

overburden


59-138

Burghardt 1998
Various surveys
Orphan (|xg), AZ
median


250

San Mateo (|xg)
spoils


10-450

SanM.,NMavg.


200

Lathrop mine
(|xg), waste


270-400




250




170-180


212
(7.84)
54
(2.0)



57
(2.11)
81
(3.0)



2.7
(0.1)
6.3
(0.23)



40
(1.48)
47
(1.74)


Muss

4.3
(0.16)




1.28
(0.05)




4.3
(0.16)


Jomac
163
(6.03)
110
(4.1)



35
(1.3)
206
(7.62)


Cath. Butte
17
(0.63)
25
(0.93)


Blue N.
7.3
(0.28)
8.5
(0.31)



22
(0.81)
26
(0.96)


W. Rk. Cn.
15.3
(0.57)
18
(0.67)



32
(0.67)
21
(0.78)


Terry
188
(6.96)
170
(6.29)


AV-4

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
Burghardt 1998
Various surveys
(cont.)

2.3
(0.09)
3.2
0.12)


Rainy Day
70
(2.59)
48
(1.78)



56.7
(2.1)
1.5
(0.06)



1.7
(0.06)
3.8
(0.14)



3.1
(0.11)
12
(0.44)


Longsworth 1994
Monument Valley
Cameron area
AZ/UT


Moonlight Mine


18-22




43-630




185-320

Jeepster


18-23




19-20




5-20




47-150

Jack Daniels


70-190




35-220




27-85




33-75

Moore et al. 1996
South spoil, drill
hole avg.
85 ppm



Midnite Mine,
WA
Hillside spoil,
drill hole avg.
82 ppm



AVI 1986
Shirley Basin,
WY




all piles, avg.

11.5
(0.43)


LAI 1996
Rox ore pile, avg.


400

GV area, avg.


120

H&I, avg.


150

G spoils, avg.


150

Stan claims, avg.


500

B/R spoils, avg.


150

2States/Bl, avg.


250

Umetco, spoils, E


120

S


280

Sunset sp, avg.


200

max.


2,000

S-T spoils


50-150

Bullrush, avg.


90

P73 av


300

Classic/Bar
protore


300-500

North Rex, avg.


40

AV-5

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
HE 1989
Pix-Veca pile,
drill hole avg.

11.4
(0.42)


P-V, avg. 1,200
meas.


113
(4.2)

P-V surface avg.

27.2
(1.0)


AVI 1990
Poison Basin-
protore

55-140
(2.04-5.18)
250-600

HE 1987
Pump Bts. Smpls
35
(1.3)
87
(3.22)
170


52
(1.92)
126
(0.44)
300


27
(1.0)
45
(1.67)
105


2.1
(0.08)
9
(0.33)
70

Jean-avg. ore
piles


140

Key- below
ground
22.1
(0.82)
12.7
(0.47)
40

waste
20.9
(0.77)
32.8
(1.21)
70

ore
688
(25.46)
185.6
(68.67)
300

FPE1988
Gas Hills-Jgpile,
avg.

33.8


Jpile, avg.

15.5
(0.57)


Kpile, avg.

7.2
(0.27)


WY AML Project
15
Converse County,
WY




Avg. of 677,482
yds




of protore
170 ppm



Site II-avg.

51
(1.89)
74
30.7
(1.14)
range

17-180
(0.63-6.67)
3.4-160

Average all drill
hole in
waste/protore
piles 11 sites
93.6ppm
49.6
(1.84)


RCT 1994
Range of 82
smpls of
soil/spoil from 10
sites
<.85-668 ppm



AV-6

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
U.S. BLM 1986
Jackpile-Paguate,
NM




Dump A waste
4.5 ppm

11
(0.41)

B waste
2.7 ppm

10
(0.37)

C waste
2.7 ppm

5
(0.19)

D waste
4.05 ppm

5
(0.19)

E waste
1.5 ppm

5
(0.19)

F waste
4.03 ppm

5
(0.19)
1.1
(0.04)
G waste
5.82 ppm

5
(0.19)
4.15
(0.15)
H waste
146.8 ppm

29
(1.07)

I waste
10.0 ppm

5
(0.19)

J waste
10.66 ppm

75
(2.78)

K waste
20.30 ppm

7
(0.26)
2.7
(0.10)
L waste
5.5 ppm

5
(0.19)
2.57
(0.1)
N waste
42.0 ppm

9
(0.33)

N2 waste
200.0 ppm

30
(1.11)

O, P,P1,P2
waste
3.12 ppm

12
(0.44)

Q waste
160.0 ppm

68
(2.52)

R waste
11.0 ppm

24
(0.89)

S waste
2.79 ppm

10
(0.37)

T waste
3.9 ppm

9
(0.33)

U waste
34.3 ppm

52
(1.92)

V waste
13.9 ppm

34
(1.26)

W waste
2.5 ppm

10
(0.37)

X waste
18.0 ppm

5

Y waste
33.4 ppm

13

AV-7

-------
Table AV.l Radiochemical, Exposure, and Radon Flux Data for Uranium Mine Waste
(cont.)
DataSource
Type of Data
U(nat)
pCi/g1 (Bq/g)
Ra-226
pCi/g1 (Bq/g)
MicroR/hr
Radon Flux
U.S. BLM 1986
Y2 waste
4.2 ppm

5

(cont.)
South waste
4.9 ppm

8


FD-1 waste
2.7 ppm

10


FD-2 waste
45.0 ppm

3


FD-3 waste
14.0 ppm

28


17BC pro tore
220.0 ppm

581


6A protore
200.0 ppm

388


6B protore
130.0 ppm

383


J1 protore
94.0 ppm

155


J2 protore
490.0 ppm

606


17D protore
520.0 ppm

198


IB protore
140.0 ppm

237


2C protore
110.0 ppm

422


10 protore
390.0 ppm

506


2D protore
180.0 ppm

419


1C protore
61.0 ppm

227


1A protore
31.0 ppm

161


2E protore
220.0 ppm

451


SP-1 protore
130.0 ppm

354


PLG protore
5.0 ppm

210


4-1 protore
77.0 ppm

266


SP-2 protore
180.0 ppm

300


SP-2B protore
610.0 ppm

164


TS-1 soil pile
4.9 ppm

8


TS-2A soil pile
4.9 ppm

18


TS-2B soil pile
2.9 ppm

6


TS-3 soil pile
3.6 ppm

11


Topsoil borrow
4.1 ppm

17

Otton 1998
Ascension mine
Front Range of
CO




Waste/prot avg.
41 sites

45.7
(1.69)



Protore range

294-421
(10.88-15.58)
680-1,100

AV-8

-------
Table AV.2 Radionuclide Concentrations in Ponds and Streams Associated
with Open-pit Mines in Arizona, Texas, Utah and New Mexico
Data Source
Type of Data
U-238
PPb
U-235
pCi/L
Ra-226
pCi/L
Longsworth 1994
Monument Valley
area, AZ-UT




Moonlight
Mine—shallow well
11000
440
(1.63)
44
(1.63)
AZ-UT deposits
Moonlight
Mine—shallow well
14000
530
(19.61)
110
(4.07)

Moonlight Mine—pit
water
-
-
8.6
(0.32)

Radium
Hill—drillhole water
210
12
(0.04)
19
(0.7)

Radium Hill—shallow
well
0.5
<0.1
0.16
(0.01)

Cameron area, AZ




Jeepster Mine—pit
water
22
0.8
(0.03)
0.25
(0.01)

Jack Daniels
Mine—ground water
150
5.7
(0.21)
0.1

Jack Daniels
Mine—pit water
11
0.4
(0.01)
0.07

Manuel-Denetsone
—drillhole water
180
8.9
(0.33)
0.52
(0.02)

Ramco No. 20—small
pit water
15
0.6
(0.02)
0.09


Uppb


RCT 1994
Texas mines.
Open-pit mine water
samples




Stoeltje
600




700



Manka
250




200




300




220



I.M. Brysch
12




<1




14



Galen
<1



Butler
180




180




42




45




<1




<1




65


AV-9

-------
Table AV.2 Radionuclide Concentrations in Ponds and Streams Associated
with Open-pit Mines in Arizona, Texas, Utah and New Mexico
(cont.)
Data Source
Type of Data
U-238
PPb
U-235
pCi/L
Ra-226
pCi/L
RCT 1994
Wright-McCrady
49


Texas mines.

49


(cont.)
Esse
49




49



Sickenius
240




230



Kopplin
72




82



Smith
4,500




4,500



Pfeil
57




25



Weddington South
25




49



Kellner-T enneco
Weddington
220




170




200




300



Franklin
18




7


U.S. BLM 1986
South Paguate—pit
pond, N.M.


21.1
(0.78)

North Paguate—pit
pond


36
(1.33)

South Jackpile—pit
pond


18
(0.67)

North Jackpile—pit
pond


16.1
(0.60)

Rio
Paguate—upstream
from mine
6

0.35
(0.01)

Rio
Moquino—upstream
from mine
8

0.28
(0.01)

Below
confluence—down
from mine
239

3.73
(0.14)

Paguate
Reservoir—down from
mine
236

1.03
(0.04)
AV-10

-------
The following licensed ISL facilities are under the environmental oversight and regulation of the NRC
and its Agreement States. The wastes from these facilities are considered byproduct materials and not
TENORM. The information presented here is for information purposes only.
Table AV.3. In Situ Leach Operation Evaporation Pond Radionuclides,
Crow Butte, Nebraska
Radionuclides
Pond Liauids (uCi/mh
Lead-210
0.66 x 10-9
Polonium-210
0.70 x 10-9
Radium
0.65 x 10-9
Radon
0.70 x 10-4
Thorium-230
2.28 x 10-9
Uranium
5.24 x 10-9
Source: NRC License Application Supporting Materials.
AV-11

-------
Table AV.4.1 In Situ Leach Operation Evaporation Pond Radionuclides COGEMA,
Irigaray Field, Wyoming
Sample Loc. /Date
Total U
mg/L
Ra 226 pCi/L
+/- Precision
Ra 226 Bq/L
+/- Precision
IR-1 01/21/99
7.0
3.9/0.3
0.14/0.01
IR-1 04/16/99
18.3
8.1/0.5
0.30/0.02
IR-2A 01/21/99
15.1
46.3/1.9
1.71/0.07
IR-2A 04/16/99
1.90
68.9/2.4
2.55/0.9
IR-2B 01/21/99
6.0
29.1/1.5
1.08/0.07
IR-2B 04/16/99
3.96
50.5/2.0
1.87/0.07
IR-3 01/21/99
1.9
17.3/1.3
0.64/0.05
IR-3 04/16/99
0.746
8.4/0.5
0.31/0.02
IR-A 01/21/99
39.8
135/4.2
5.0/0.16
IR-A 04/16/99
36.0
151/4.7
5.59/0.17
IR-B 01/21/99
11.5
471/7.8
17.43/0.29
IR-B 04/16/99
11.8
439/7.9
16.24/0.29
IR-C 01/21/99
3.2
439/7.4
16.24/0.3
IR-C 04/16/99
3.0
325/5.4
12.03/0.2
IR-D 01/21/99
6.6
580/8.6
21.46/0.32
IR-D 04/16/99
6.0
529/6.6
19.57/0.24
IR-E 01/21/99
13.6
1,716/14.6
63.49/0.54
IR-E 04/16/99
13.4
1,760/12.3
65.12/0.46
IR-RA 01/21/99
3.0
16.9/1.2
0.63/0.04
IR-RA 04/16/99
31.0
39.0/1.9
1.44/0.07
IR-RB 01/21/99
46.5
5.1/0.4
0.19/0.01
IR-RB 04/16/99
86.0
11.5/1
0.43/0.04
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-12

-------
Table V.4.2. In Situ Leach Operation Evaporation Pond Radionuclides COGEMA,
Christensen Ranch Field, Wyoming
Samnle T.nc. /Date
Total TT
Ra 226 nCi/T,
Ra 226 Rn/T,
CR-1 01/21/99
8.6
107/2.9
3.96/0.11
CR-1 04/16/99
6.6
97.5/2.8
3.61/0.1
CR-2 01/21/99
1.10
1.5/0.2
0.06/0.01
CR-2 04/16/99
18.10
3.1/0.3
0.11/0.01
CR-3 01/21/99
0.443
1.4/0.2
0.05/0.007
CR-3 04/16/99
2.00
37.8/1.8
1.4/0.07
CR-4 01/21/99
0.07
1.5/0.2
0.06/0.007
CR-4 04/16/99
0.3160
23.7/1.4
0.88/0.05
CR-P1 01/21/99
0.021
0.8/0.2
0.03/0.007
CR-P1 04/16/99
0.0166
6.0/0.4
0.22/0.15
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-13

-------
Table AV.5. In Situ Leach Operation Evaporation Pond Radionuclides,
Power Resources, Inc. Highlands Uranium Project, Wyoming
Purge Storage Reservoir PSR-1
Purge Storage Reservoir PSR-2
Date
Ra-226
Date
Ra-226
pCi/L
Bq/L
pCi/L
Bq/L
01/10/97
3.14
0.12
01/09/97
5.50
0.20
02/03/97
1.36
0.05
02/07/97
2.47
0.09
03/05/97
2.26
0.08
03/05/97
3.70
0.14
04/01/97
2.10
0.07
04/03/97
9.50
0.35
05/05/97
2.00
0.07
05/08/97
7.45
0.27
06/03/97
2.10
0.07
06/18/97
1.20
0.04
07/02/97
2.24
0.08
07/03/97
2.15
0.08
08/04/97
1.50
0.06
08/01/98
4.50
0.17
09/03/97
5.60
0.21
09/05/97
4.20
0.16
10/02/97
1.34
0.05
10/16/97
1.38
0.05
11/06/97
4.13
0.15
11/13/97
5.60
0.21
10/01/97
2.36
0.09
12/03/97
8.10
0.30
01/05/98
6.70
0.25
01/06/98
2.30
0.09
02/02/98
2.68
0.10
02/10/98
3.60
0.13
03/02/99
2.99
0.11
03/10/99
3.10
0.11
04/07/98
1.21
0.04
04/06/98
1.71
0.06
05/04/98
3.60
0.13
05/07/98
2.10
0.08
06/03/98
4.10
0.15
06/09/98
4.00
0.15
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-14

-------
Table AV.5. In Situ Leach Operation Evaporation Pond Radionuclides,
Power Resources, Inc. Highlands Uranium Project, Wyoming (cont.)
E Radium Settling Basin
W Radium Settling Basin
Date
U Total
Ra-226
U Total
Ra-226
pCi/L
Bq/L
pCi/L
Bq/L
pCi/L
Bq/L
pCi/L
Bq/L
03/20/97
4.60
0.17
1.30
0.05
5.30
0.20
8.30
0.31
06/30/97
3.00
0.11
5.10
0.19
3.00
0.11
5.10
0.19
09/03/97
2.26
0.08
8.00
0.30
2.18
0.08
1.20
0.04
12/30/97
5.96
0.22
7.00
0.26
4.29
0.16
1.10
0.04
03/24/98
4.80
0.18
1.20
0.04
3.61
0.13
2.80
0.10
06/22/98
4.85
0.18
1.30
0.05
2.26
0.08
9.00
0.33
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-15

-------
Table AV.6. In Situ Leach Operation Evaporation Pond Radionuclides Rio Algom
Mining Corp. (Now owned by Power Resources) Smith Ranch Project, Wyoming
Evaporation Pond Water Analyses Q&S Sand In Situ Leaching
Location
Date
East Cell
West Cell
II mg/L
Ra226
pCi/L (Bq/L)
Th230
pCi/L (Bq/L)
II mg/L
Ra226
pCi/L (Bq/L)
Th230
pCi/L (Bq/L)
1st Qtr. 1982
1,100
2,378 (87.99)

16
172 (6.36)

2nd Qtr. 1982
784
456 (16.88)

49
1,804 (66.75)

3rd Qtr. 1982
38
100 (3.7)

132
2,119(78.4)

4th Qtr. 1982
275
315 (11.66)

131
1,779 (65.82)

1st Qtr. 1983
4
86 (0.15)

2
22 (0.81)

2nd Qtr. 1983
79
216(0.96)

1
36(1.33)

3rd Qtr. 1983
13
108 (0.07)

14
44(1.63)

4th Qtr. 1983
103
483 (17.87)

100
553 (20.46)

1st Qtr. 1984
22
42(1.55)

1
34(1.26)

2nd Qtr. 1984
55
183 (6.77)

121
224 (8.29)

3rd Qtr. 1984
105
21 (0.78)

105
7 (0.26)

4th Qtr. 1984
141
5,095 (188.52)

--
--

1st Qtr. 1985
12
3,030 (112.11)

	
	

2nd Qtr. 1985
.20
643 (23.79)

.17
1,149 (42.51)

3rd Qtr. 1985
.23
510(18.87)

.23
490(18.13)

4th Qtr. 1985
.21
754 (27.90)

.22
552 (20.42)

1st Qtr. 1986
.33
184 (6.8)

.14
423 (15.65)

2nd Qtr. 1986
.25
1,366 (50.54)

.20
923 (34.15)

3rd Qtr. 1986
.39
3,253 (120.36)

.38
2,081 (77.0)

4th Qtr. 1986
.32
4(0.15)

.27
41 (1.52)

1st Qtr. 1987
.24
772 (2.86)

.25
755 (27.94)

2nd Qtr. 1987
.25
1912 (70.74)

.23
560 (20.72)

1st Half 1997
69.7
3,230 (119.51)
15.4 (0.57)
137
74.6 (2.76)
1.1 (0.04)
2nd Half 1997
27.8
57.1 (2.11)
0



2nd Half 1999
92.4
945 (34.97)
6.2 (0.23)
70.8
203 (0.1)
0.7(0.03)
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-16

-------
The evaporation ponds were being sampled semiannually. Gamma radiation was measured quarterly at
the evaporation ponds. The measurements obtained during the 1st & 2nd quarters of 1999 were 71 and 27
uR/hr, respectively.
Table AV.7. Evaporation Pond Leaks, Smith Ranch Project, Wyoming
Location
Date
U (nat) mg/L
East Pond
01/13/99
6.19
East Pond Stand Pipe
01/13/99
6.89
East Pond Stand Pipe
02/08/99
25.8
East Pond Sump
05/04/99
28
West Pond Sump
05/04/99
65
West Pond Sump
06/25/99
166
West Pond
10/23/99
75
West Pond Sump
10/23/99
193
West Pond Sump
10/29/99
150
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
Table AV.8. Deep-well Injection, Smith Ranch In Situ Leach Facility, Wyoming
The following is a table of the amounts and concentration of U Nat & Ra-226
disposed by UIC injection in 1998, 1999.
Date
Gals./month (liters/month)
Nat. Uranium mg/L *
Radium-226 pCi/L*
(Bq/L)
June 1998

27.5
1,250 (46.25)
Sept. 1998

5.0
1,300 (48.10)
Dec. 1998

17.5
1,550 (57.35)
Jan. 1999
1,869,362 (7,076,095.9)


Feb. 1999
1,832,431 (6,936,722.5)


Mar. 1999
1,867,385 (7,068,612.4)
10.0
1,450 (53.65)
April 1999
1,906,162 (7,215,395.0)


May 1999
1,952,301 (7,390,044.9)


June 1999
1,713,467 (6,485,960.1)
19.0
1,050 (38.85)
* = Values estimated from graph.
Source: Quarterly Environmental Reports to the Nuclear Regulatory Commission.
AV-17

-------
Appendix VI. Legal Authorities Concerning Uranium,
Uranium Mines and Extraction Facilities
Introduction
This section presents information on the authorities under which major federal, state and Tribal
agencies operate. These authorities have been used to establish regulatory standards and
requirements, and could potentially be used to develop additional guidances, or take other actions
for the control of uranium TENORM, uranium mining, and uranium extraction facilities.
U.S. EPA
More than a dozen major statutes or laws form the legal basis for the programs of the EPA. EPA
authority to develop radiation protection standards and to regulate radioactive materials including
TENORM is derived from a number of those federal laws, plus Executive Orders.
The authority to develop Federal guidance for radiation protection was originally given to the
Federal Radiation Council (FRC) by Executive Order in 1959 as an offshoot of authorities of the
Atomic Energy Act (42 U.S.C. 2011 et seq.)(1954). Over the next decade the FRC developed
federal guidance ranging from guidance for exposure of the general public, to estimates of fallout
from nuclear weapons testing. Federal guidance developed by the FRC provided the basis for
most regulation of radiation exposure by federal and state agencies, prior to the establishment of
the EPA.
In 1970, the responsibility for developing Federal guidance for radiation protection was
transferred from the FRC to the newly formed EPA under Executive Order 10831 and
Reorganization Plan No. 3. Federal Guidance Documents are signed by the President and issued
by EPA. By signing these, the President provides a framework for federal and state agencies to
develop regulations that ensure the public is protected from the harmful effects of ionizing
radiation. Federal Guidance is also an opportunity for the President to promote national
consistency in radiation protection regulations. For example, the guidance document Radiation
Protection Guidance to Federal Agencies for Occupational Exposure, issued by EPA in 52 CFR
2822 January 27, 1987, established general principles, and specifies the numerical primary guides
for limiting worker exposure to radiation.
Clean Air Act (CAA)
EPA regulates radon and radioisotope emissions through its authority under the Clean Air Act (42
USC 7401 et seq.) (1970). Regulations promulgated by the Agency which control radioactive
facilities and sites include 40 CFR 61:
•	Subpart B, Underground Uranium Mines
•	Subpart H, Department of Energy Facilities
•	Subpart I, Certain non-DOE Facilities
•	Subpart K, Elemental Phosphorous Plants
•	Subpart R, Radon from Phosphogypsum Stacks
•	Subpart W, Operating Uranium Mill Tailings
Under Subpart B, emissions of radon-222 to the ambient air from an underground uranium mine
may not exceed amounts that would cause any member of the public to receive in any year an
AVI-1

-------
effective dose equivalent of 10 mrem/y. Operators must provide a report to EPA annually on their
compliance with the standard.
Under Subpart W, operating uranium mills must comply with the radon emission requirements of
20 pCi/(m2-sec)(1.9 pCi/(ft2-sec)) of radon-222, and other provisions under EPA's UMTRCA
requirements in 40 CFR 192.32(a). Operators must provide a report to EPA annually on their
compliance with the standard.
Under the Radon Gas and Indoor Air Quality Research Act (USC 42 et seq.)(1986) and Indoor
Radon Abatement Act (1988), as well as authorities of the CAA, EPA has developed guidance for
control of radon in homes, buildings and schools, and more recently for drinking water treatment
and wastewater treatment facilities (U.S. EPA 2005, ISCORS 2005). The CAA gives EPA the
authority to regulate emissions of both "conventional" pollutants, like PMi0 (particulate matter
less than 10 microns), and hazardous pollutants, such as radon. Both of these air pollutants are
emitted by uranium extraction and beneficiation activities.
Clean Water Act (CWA)
The Clean Water Act's (33 USC 121 et seq., 1977) primary objective is to restore and maintain
the integrity of the nation's waters. This objective translates into two fundamental national goals:
eliminate the discharge of pollutants into the nation's waters, and achieve water quality levels that
are fishable and swimmable. Under this law, EPA is given the authority to establish water quality
standards and regulate the discharge of pollutants into waters of the United States, and this is
performed under EPA's National Pollutant Discharge Elimination System (NPDES). A point
source is defined as any discrete conveyance, natural or man made, including pipes, ditches, and
channels, and NPDES permits are issued by EPA or delegated States.
Section 502(6) of the CWA includes "radioactive materials" in the definition of pollutants. EPA's
implementing regulations at 40 CFR 122.2, which defines the term "pollutants" includes
radioactive materials except those regulated under the AEA. The law also gives EPA the
authority to regulate, through permits, storm water discharges from both inactive and active mine
sites. Mines and mills that discharge must obtain a permit, and must monitor twice a year for
specific pollutants determined by the type of ore they mine or process. EPA regulations in 40
CFR 440, Part C, are applicable to discharges from (a) mines either open-pit or underground (ISL
operations are excluded), from which uranium, radium and vanadium ores are produced; and (b)
mills using the acid leach, alkaline leach, or combined acid and alkaline leach process for the
extraction of uranium, radium and vanadium.
These regulations provide effluent limitations based upon best practicable control technology
(BPT) and best achievable technology (BAT) for uranium mills and open-pit and underground
uranium mines, including mines using ISL methods. Discharges from regulated operations must
meet best available technology/best practicable technology (BAT/BPCT) standards for zinc,
arsenic, ammonia, dissolved radium-226, total radium, uranium, total suspended solids (TSS),
chemical oxygen demand (COD), and pH. A summary of the standards is included in Chapter 1,
as well as in more detail in U.S. EPA (1995a), and 40 CFR 440 Subpart C: 440.32, 440.33, and
440.34. Individual states are required to adopt water quality criteria at least as stringent as federal
levels. The application of these criteria is based on the designated use of a specific receiving
water (drinking water supply, aquatic life, and/or recreational use).
AVI-2

-------
Except as provided in cases of unusually high storm water events, EPA has regulated that there
shall be no discharge of process wastewater to navigable waters from mills using the acid leach,
alkaline leach or combined acid and alkaline leach process for the extraction of uranium or from
mines and mills using ISL methods. The only exception occurs if annual precipitation falling on
the treatment facility and the drainage area contributing surface runoff to the mine or mill's water
treatment facility exceeds the annual evaporation. In such cases, the volume of water exceeding
annual evaporation may be discharged subject to the numerical limitations for uranium and
radium discharge mentioned above.
Some discharges from mine sites do not meet the definition of a "point source discharge." These
discharges are nonpoint source discharges. Under Section 319 of the CWA, States are required to
prepare nonpoint source assessment reports and to develop programs to address nonpoint sources,
including active and inactive/abandoned mine sites, on a watershed-by-watershed basis. Each
state must report to EPA annually on program implementation and resulting water quality
improvements.
Safe Drinking Water Act (S D W A)
The Safe Drinking Water Act (42 USC 300f et seq., 1974), is the main federal law that ensures
the quality of Americans' drinking water. Under the SDWA, EPA sets standards for drinking
water quality and oversees the states, localities, and water suppliers who implement those
standards. Implementing regulations for 40 CFR 141 include the establishment of national
primary drinking water standards which currently include maximum contaminant level goals and
maximum contaminant levels (MCLs) for radiation and radionuclides. The standards also include
combined Ra-226 and Ra-228, Uranium, gross alpha excluding uranium and radon, man-made
beta and photon emitters. A draft MCL has also been proposed for Radon. EPA established a UIC
program under the authority of the SDWA. Through this program, the Agency has a permit
system to ensure underground sources of drinking water are protected from the injection of
process fluids and liquid wastes, including those produced during uranium extraction and
beneficiation, into the subsurface via wells.
EPA's UIC regulations protect underground sources of drinking water (USDWs) by prohibiting
the direct injection or migration of foreign fluids into these aquifers. A USDW is defined as any
aquifer or its portion that supplies a public water system or contains fewer than 10,000 mg/1 total
dissolved solids (TDS). An aquifer may be exempted from UIC regulation if it is shown to be
completely isolated with no possible future uses. In general, federal regulations prohibit any
underground injection unless authorized by permit or by rule. In addition, no owner/operator of a
well may construct, operate, maintain, convert, plug, or abandon an injection well in a manner
which allows the movement of contaminated fluid into underground sources of drinking water.
The program establishes requirements for five injection well categories. Regulations vary
according to the class of well. These categories are outlined below:
Class I: Injection wells for hazardous, industrial, non-hazardous, and municipal wastewater
disposal below the lower most formation, within 1/4 mile of the wellbore, containing an
underground source of groundwater.
Class II: Injection wells for fluids related to oil and gas production such as salt water disposal
wells, enhanced oil recovery wells and hydrocarbon storage wells.
AVI-3

-------
Class III: Injection wells related to mineral extraction such as ISL production of uranium, only for
ore bodies which have not been conventionally mined.
Class IV: Disposal of radioactive or hazardous waste into or above a formation which contains an
underground source of drinking water within 1/4 mile. Section 3020(a) of RCRA prohibits the
construction and operation of Class IV wells.
Class V: Injection wells not included in the other classes. This includes solution mining of
conventional mines, such as isotope leaching and low-level radioactive waste wells.
Classes I, III and V are potentially applicable to the uranium extraction and beneficiation
industry. Enforcement of the requirements of the SDWA may be delegated by EPA to states.
Under the regulations, EPA may permit injection wells for uranium ISL operations. EPA's
regulations issued under UMTRCA authority provide the principal standards for uranium ISL
operations and groundwater protection, while the UIC regulations are considered additional
requirements for ISL operations. Under UIC permits, the Agency usually exempts that portion of
an aquifer constituting the well field from meeting drinking water standards. However, under
EPA standards established under UMTRCA authority, the operator of the ISL restores the well
field to either background conditions or EPA drinking water maximum contaminant limit levels
where possible or practical. When this can not be accomplished, Alternate Concentration Limits
(ACLs), in terms of the presence of metals, organics, pH level, and radioactivity, may be
approved by the NRC or its Agreement States, with EPA concurrence.
CERCLA (Supcrfund)
The Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) (42
USC 9601 et seq.,1980) and the Superfund Amendments and Reauthorization Act (SARA) (42
USC 9601 et seq., 1986) provided broad Federal authority to respond directly to releases or
threatened releases of hazardous substances that may endanger public health or the environment.
CERCLA established prohibitions and requirements concerning closed and abandoned hazardous
waste sites; provided for liability of persons responsible for releases of hazardous waste at these
sites; and established a trust fund to provide for cleanup when no responsible party could be
identified. EPA has determined that radiation is a carcinogen and thus a hazardous substance.
Under the National Oil and Hazardous Substances Contingency Plan (NCP), EPA has issued
guidance on removals and cleanup of radioactively contaminated sites, including those
contaminated with the TENORM radionuclides radium, thorium and uranium. Implementing
regulations for the NCP are found at 40 CFR 300.
The Toxic Substances Control Act (TSCA)
The Toxic Substances Control Act (TSCA) (15 USC 2601 et seq., 1976) was enacted by
Congress to give EPA the ability to track the 75,000 industrial chemicals currently produced or
imported into the United States. EPA repeatedly screens these chemicals and can require
reporting or testing of those that may pose an environmental or human health hazard. EPA can
ban the manufacture and import of those chemicals that pose an unreasonable risk. While
radionuclides are considered toxic substances under the Act, source material, special nuclear
material, or byproduct material (as such terms are defined in the AEA, and regulations issued
under such Act) are excluded from coverage. Consequently, TENORM radionuclides may be
subject to this law, though EPA has not previously applied it in this way.
AVI-4

-------
The Resource Conservation and Recovery Act (RCRA)
The Resource Conservation and Recovery Act (RCRA) (42 USC 321 et seq., 1976) gave EPA the
authority to control hazardous waste. This includes the generation, transportation, treatment,
storage, and disposal of hazardous waste. RCRA also set forth a framework for the management
of non-hazardous wastes. The 1986 amendments to RCRA enabled EPA to address
environmental problems that could result from underground tanks storing petroleum and other
hazardous substances. RCRA focuses only on active and future facilities and does not address
abandoned or historical sites (see CERCLA). HSWA (the Federal Hazardous and Solid Waste
Amendments) are the 1984 amendments to RCRA that required phasing out land disposal of
hazardous waste. Some of the other mandates of this strict law include increased enforcement
authority for EPA, more stringent hazardous waste management standards, and a comprehensive
underground storage tank program. EPA's implementing regulations for RCRA do not
address disposal of radioactively contaminated substances in landfills, however nuclear
accelerator wastes (a form of waste previously classified as part of the TENORM waste class) has
been disposed of in such facilities, depending on the permitting authority.
Uranium Mill Tailings Radiation Control Act (UMTRCA)
EPA does not license uranium mills or ISL facilities. However, it does establish certain
environmental standards which must be adopted by the NRC and its Agreement States and DOE
for uranium processing facilities. Current regulations applicable to remediation of both inactive
uranium mill tailings and uranium extraction facilities, including vicinity properties and ISL
operations, active uranium and thorium mills, and ISL operations, have been issued by the EPA
under the Uranium Mill Tailings Radiation Control Act (UMTRCA) (42 USC 2022 et seq.) of
1978, as amended. EPA's regulations in 40 CFR 192 apply to remediation of such properties and
address emissions of radon, as well as radionuclides, metals, and other contaminants into surface
and groundwater.
Under UMTRCA, EPA has the responsibility to establish standards for exposure of the public to
radioactive materials originating from mill tailings, and for cleanup and control standards for
inactive uranium processing sites and associated vicinity areas, as well as for active uranium
extraction facilities licensed by the NRC or its Agreement States. To the maximum extent
possible, those standards were required to reflect the requirements issued by EPA under the Solid
Waste Disposal Act (now RCRA), and do so by referencing 30 CFR Part 261 regulations.
Tailings or wastes produced by the extraction or concentration of uranium or thorium from any
ore processed primarily for its source material content is defined by Section 1 le.(2) of the Atomic
Energy Act as byproduct material. That material is not considered to be TENORM in the U.S.,
and is regulated by the NRC or its Agreement States. Under UMTRCA, the NRC must utilize
EPA environmental protection standards to develop its regulations for active and inactive
uranium milling and extraction facilities. The NRC does not have regulatory authority over
conventional type uranium mine wastes (see NRC discussion below).
AVI-5

-------
U.S. Nuclear Regulatory Commission
The mission of the NRC is to ensure adequate protection of the public health and safety, the
common defense and security, and the environment in the use of nuclear materials in the United
States. The NRC's scope of responsibility includes regulation of commercial nuclear power
reactors; research, test, and training reactors; fuel cycle facilities; medical, academic, and
industrial uses of nuclear materials; and the transport, storage, and disposal of nuclear materials
and waste.
The NRC was created as an independent agency by the Energy Reorganization Act of 1974,
which abolished the AEC and moved the AEC's regulatory function to NRC. This act provides
the foundation for regulation of the nation's commercial nuclear power industry.
NRC regulations are issued under the United States Code of Federal Regulations (CFR) Title 10,
Chapter 1. Principal statutory authorities that govern NRC's work are:
•	Atomic Energy Act of 1954, as amended
•	Energy Reorganization Act of 1974, as amended
•	Uranium Mill Tailings Radiation Control Act of 1978, as amended
•	Nuclear Non-Proliferation Act of 1978
•	Low-Level Radioactive Waste Policy Act of 1980
•	West Valley Demonstration Project Act of 1980
•	Nuclear Waste Policy Act of 1982
•	Low-Level Radioactive Waste Policy Amendments Act of 1985
•	Diplomatic Security and Anti-Terrorism Act of 1986
•	Nuclear Waste Policy Amendments Act of 1987
•	Solar, Wind, Waste and Geothermal Power Production Incentives Act of 1990
•	Energy Policy Act of 1992
The NRC and its licensees share a common responsibility to protect the public health and safety.
Federal regulations and the NRC regulatory program are important elements in the protection of
the public. NRC licensees, however, have the primary responsibility for the safe use of nuclear
materials.
The NRC fulfills its responsibilities through a system of licensing and regulatory activities that
include:
1)	Licensing the construction and operation of nuclear reactors and other nuclear facilities,
such as nuclear fuel cycle facilities and test and research reactors, and overseeing their
decommissioning;
2)	Licensing the possession, use, processing, handling, and export of nuclear material;
3)	Licensing the siting, design, construction, operation, and closure of low-level radioactive
waste disposal sites under NRC jurisdiction and the construction, operation, and closure
of the geologic repository for high-level radioactive waste;
4)	Licensing the operators of nuclear power and non-power test and research reactors;
inspecting licensed facilities and activities;
5)	Conducting the principal U.S. Government research program on light-water reactor
safety;
6)	Conducting research to provide independent expertise and information for making timely
regulatory judgments and for anticipating problems of potential safety significance;
AVI-6

-------
7)	Developing and implementing rules and regulations that govern licensed nuclear
activities;
8)	Investigating nuclear incidents and allegations concerning any matter regulated by the
NRC;
9)	Enforcing NRC regulations and the conditions of NRC licenses;
10)	Conducting public hearings on matters of nuclear and radiological safety, environmental
concern, common defense and security, and antitrust matters;
11)	Developing effective working relationships with the States regarding reactor operations
and the regulation of nuclear material;
12)	Maintaining the NRC Incident Response Program, including the NRC Operations Center;
and
13)	Collecting, analyzing, and disseminating information about the operational safety of
commercial nuclear power reactors and certain non-reactor activities.
Atomic Energy Act - Regulation of Source Material
Under the AEA, the AEC, now the NRC, was given responsibility for regulation of "source
material". Source material includes either the element thorium or the element uranium, provided
that the uranium has not been enriched in U-235. Source material also includes any combination
of thorium and uranium, in any physical or chemical form, or ores that contain by weight 0.05
percent or more of uranium, thorium, or any combination thereof. Depleted uranium (left over
from uranium enrichment) is considered source material. Source material can result from the
milling and concentration of uranium contained in ore mined for its uranium content. As the
chemical refining processes are generally the same, the NRC also regulates source material
generated from ISL operations. It can also be generated in the process of refining ores mined for
other precious metals. In addition, source material can arise from the reprocessing of spent
nuclear fuel (no commercial reprocessing is currently licensed in the U.S.) and also, as depleted
uranium (contains lower levels of U-235 than natural uranium), from the process of enriching
uranium in the isotope U-235. However, the NRC does not regulate conventional (open-pit and
underground) mining of uranium or thorium ore. NRC's regulations for source material facility
licensing are found at 10 CFR 40.
Guidance for applications for ISL operation licenses are contained in NUREG 1569 (U.S. NRC
2003). An applicant for a new operating license, or for the renewal or amendment of an existing
license, is required to provide detailed information on the facilities, equipment, and procedures to
be used and to submit an environmental report that discusses the effect of proposed operations on
public health and safety and the impact on the environment. This information is used by NRC
staff to determine whether the proposed activities will be protective of public health and safety
and will be environmentally acceptable.
Regulations in 10 CFR Part 51, provide for environmental protection regulations for domestic
licensing and related regulatory functions, while those in 10 CFR Part 20 cover radiation
protection standards. Fuel cycle facility inspections which enforce these regulations focus on the
areas that are most important to safety and safeguards, using objective measures of performance
called "performance indicators." Inspections at fuel cycle facilities occur several times a year and
typically cover activities such as chemical process, emergency preparedness, fire safety, and
radiation safety. Uranium mill facilities in standby status (non-operational) are inspected every
three years. Also, specialized inspections are conducted using personnel from NRC headquarters
in Maryland and the Region II office in Atlanta, Georgia. Inspectors follow guidance in the NRC
Inspection Manual that contains objectives and procedures to use for each type of inspection. The
inspection program for fuel cycle facilities is being revised to accommodate the use of risk
AVI-7

-------
insights to focus the NRC and its licensees on matters that are most important to safety and
safeguards.
Atomic Energy Act— Regulation of Byproduct Material
Section 1 le.(2) byproduct material, as defined by the AEA, is regulated by the NRC under 10
CFR Part 40. In Part 40, the NRC clarified the definition of byproduct material by adding the
clause "including discrete surface wastes resulting from uranium solution extraction processes."
In simpler terms, it is the waste and tailings generated by the processing of ore for its uranium or
thorium content. Most of this material is created by uranium milling and is primarily mill tailings.
Examples of milling wastes are broken pipe from ISL facilities and contaminated mill equipment
that is to be discarded. Byproduct material from uranium mining and milling is disposed of in
uranium mill tailings impoundments.
Under the Energy Policy Act of 2005, the Atomic Energy Act was amended to place additional
"discrete sources of naturally occurring radioactive material" under NRC jurisdiction. The
primary focus of this provision is on security and the potential misuse of such materials. This
suggests that the materials of concern will be those that are highly radioactive in small quantities,
though "discrete" in this context will be defined further after consultation between NRC and the
EPA, and the states, as well as through the regulatory process. These wastes are not those
resulting from uranium or thorium processing.
The definition of byproduct materials was modified by the Act to include: "Any discrete source
of Ra-226 that is produced, extracted or converted after extraction, before, on or after the date of
enactment of this paragraph (August 8, 2005) for use for a commercial, medical, or research
activity, or (B) any material that (i) has been made radioactive by use of a particle accelerator,
and (ii) is produced, extracted, or converted after extraction, before, on, or after the date of
enactment of this paragraph for use for a commercial, medical or research activity;
and
any discrete source of naturally occurring radioactive material, other than source material, that:
(A) the Commission, in consultation with the Administrator of the Environmental Protection
Agency, the Secretary of Energy, the Secretary of Homeland Security, and the head of any other
appropriate Federal agency, determines would pose a threat similar to the threat posed by a
discrete source of radium-226 to the public health and safety or the common defense and security,
and (B) before, on, or after the date of enactment of this paragraph (August 8, 2005) is extracted,
or converted after extraction for use in a commercial, medical or research activity."
Waste disposal for this new class of byproduct material must be in a disposal facility that: (a) is
adequate to protect public health and safety, and (b)(i) is licensed by the Commission; or(ii) is
licensed by a state that has entered into an agreement with the Commission under section, if the
licensing requirements of the state are compatible with the licensing requirements of the
Commission. The Act also included provisions to allow disposal in a non-NRC licensed facility.
States with Agreement State status can receive authority over byproduct material. However, in
states without Agreement State status, the NRC retains authority over byproduct material.
AVI-8

-------
Uranium Mill Tailings Radiation Control Act
The U.S. Government began to purchase uranium for defense purposes in the early 1940's. Since
that time, large quantities of tailings have been generated by the uranium milling industry. In
many cases, these tailings were dispersed from impoundments and piles by natural forces and by
humans for construction use in or around buildings, or for roads. UMTRCA, which in 1978
amended the AEA, established two programs to protect the public health, safety and the
environment from uranium mill tailings.
Title I of UMTRCA addresses 22 Congressionally designated sites (to which DOE added 2 more)
that were inactive (e.g., all milling had stopped and the site was not licensed by the NRC). Title II
of UMTRCA addresses active sites (those with NRC or Agreement State licenses)
(48 FR 45926). UMTRCA requires the NRC to concur with remedies DOE selects for cleaning
up and controlling inactive sites. Under UMTRCA, the NRC is also responsible for licensing
inactive uranium tailings sites that have undergone remediation. Inspection, reporting, and record-
keeping requirements are defined in 10 CFR 40.27 under which mill tailings impoundment and
some adjoining land will be turned over to the DOE, another federal agency designated by the
President, or the state in which the site is located for long-term care. License termination usually
involves a confirmation that all applicable reclamation requirements have been met. This includes
ensuring completion of stabilization work for the tailings consistent with the accepted reclamation
plan and a determination that the licensee has complied with all standards applicable to land
structures, and groundwater cleanup.
U.S. Department of Energy
In the 1970s, the Atomic Energy Commission was abolished and the Energy Reorganization Act
of 1974 (42 USC. Sec. 5813, 5817, et seq.) created two new agencies: the Nuclear Regulatory
Commission to regulate the nuclear power industry and the Energy Research and Development
Administration to manage the nuclear weapon, naval reactor, and energy development programs.
However, the extended energy crisis of the 1970s soon demonstrated the need for unified energy
organization and planning. The Department of Energy Organization Act (42 USC Sec. 5916,
7112, et seq.) brought the Federal Government's energy agencies and programs into a single
agency. Established on October 1, 1977, the Department of Energy assumed the responsibilities
of the Federal Energy Administration, the Energy Research and Development Administration,
and parts and programs from several other agencies.
The Department of Energy's overarching mission is to advance the national, economic and energy
security of the United States; to promote scientific and technological innovation in support of that
mission; and to ensure the environmental cleanup of the national nuclear weapons complex.
Uranium Mill Tailings Radiation Control Act
Principal responsibility for management of uranium mill tailings facilities under UMTRCA is
handled by DOE's Office of Legacy Management. The office's primary functions include:
management of the land and associated resources as a federal trustee, surveillance and
maintenance associated with environmental remedies, records and information management, and
the management of post-closure liabilities. Sites transferred to the Office include UMTRCA sites,
where remediation is complete. As more sites are successfully remediated and closed, the site
AVI-9

-------
surveillance and maintenance functions, and worker benefits as appropriate, will be transferred
for long-term management.
For UMTRCA Title I disposal sites managed by the Office, DOE becomes a licensee to the NRC.
The general license for long-term custody is indefinite in duration, and the land is
administratively withdrawn from unrestricted public use. Sites located on Tribal land revert to
Tribal control, and DOE obtains a site access agreement with the Tribe that allows DOE to fulfill
its custodial responsibilities.
Title I of UMTRCA provided for the remediation and reclamation of 24 uranium mill processing
sites and approximately 5,200 associated vicinity properties by the DOE. Remediation of these
sites under DOE's UMTRA resulted in the creation of disposal cells that contain encapsulated
uranium mill tailings and associated contaminated material. The stated goals of the UMTRA
Program were to: (1) address immediate risk concerns and prevent further increases in relative
risk at all sites; (2) complete surface remedial action work at all 24 mill tailings sites and related
vicinity properties; and (3) complete ground-water activities in compliance with Environment
Protection Agency standards no later than FY 2014.
Residual radioactive material was removed from some of the Title I processing sites to off-site
disposal locations. NRC does not require a license for remediated processing sites that do not
have disposal cells, but NRC is the regulator if contaminated ground water remains. Ground
water compliance action plans, with compliance strategies that range from natural flushing to
active remediation, have been or are being developed by DOE for processing sites that have
contaminated ground water. These plans require approval by NRC and concurrence by the state
and Native American Tribe (when applicable). To date, ground water remedies have been
approved and implemented at several former uranium ore-processing sites.
The facilities regulated under Title II of the Act are both conventional uranium mill and in-situ
leach facilities that were privately owned and operated under an existing license by the NRC or
the Agreement States at the time of the passage of UMTRCA. Both Title I and Title II facilities
are subject to NRC regulations in 10 CFR Part 40 and EPA regulations in 40 CFR Part 192. Five
Title II facilities have completed reclamation and remediation, and have transitioned under the
NRC general license, and are also currently under the management of the DOE Office of Legacy
Management.
Office of Surface Mining
Congress passed the Surface Mining Control and Reclamation Act (SMCRA) (30 USC 1300, et
seq.) in 1977; the law created the Office of Surface Mining (OSM) in the Department of the
Interior. Title IV of SMCRA established the Abandoned Mine Land (AML) program, which
provides for the restoration of eligible lands and waters mined and abandoned, or left
inadequately restored. The act provides a major source of funding for reclamation of all
abandoned mine lands. SMCRA also required a fee be assessed on mined coal and allowed for
the use of these funds for abandoned mine reclamation. The funds were set aside for reclamation
of coal mines and for the closure of hazardous mine openings (adits and shafts) in other types of
mining operations.
Once a state certifies that its coal mine operations were reclaimed, these funds can be used for
reclamation at other types of mines where the properties are judged to be abandoned, or had
AVI-10

-------
become inactive prior to August 3, 1977. States can use these funds only for properties where
there is no company obligation for cleanup and the property is not listed as a National Priority
List site under CERCLA. In 1990, changes to SMCRA extended eligibility to limited sites mined
after August 3, 1977. The OSM has established guidelines to be considered when developing
plans for abandoned mine land programs and projects. They were issued to provide general
guidance to states, Indian Tribes, USDA, and OSM on the administration of reclamation activities
carried out under SMCRA. While OSM provides guidelines on reclamation requirements, the
states/Indian Tribes use their discretion on the caliber or quality of the work done at each site.
Significant use has been made of these funds for reclamation of uranium mines in the state of
Wyoming, and on the Navajo Reservation. The Hopi and Crow have also made use of these funds
for AML reclamation.
Federal Land Management Agencies
In addition to the Department of Energy, certain agencies of the U.S. Department of the Interior
and U.S. Department of Agriculture play important roles in uranium development, and
remediation of abandoned mines and mills on lands they administer. Principal among them are
Interior's Bureau of Land Management and National Park Service, and Agriculture's National
Forest Service. Each of these agencies are responsible for implementing on their lands the various
environmental laws which are administered by EPA; these include (among others) the CAA,
SDWA, CWA, TSCA, RCRA and CERCLA.
U.S. Bureau of Land Management
The BLM, an agency within the U.S. Department of the Interior, administers over 260 million
acres of America's public lands, and about 300 million additional acres of subsurface mineral
resources, located primarily in 12 Western States. The BLM's mission is to sustain the health,
diversity, and productivity of the public lands for the use and enjoyment of present and future
generations. BLM administers public lands within a framework of numerous laws. The most
comprehensive of these is the Federal Land Policy and Management Act of 1976 (FLPMA) (43
USC 1744, et seq.), though of importance for uranium extraction is its administration of mineral
development under the General Mining Law of 1872, as amended (30 USC 29 and 43 CFR 3860.
That law provides the successful mining claimant the right to patent (acquire absolute title to the
land) mining claims or sites, including uranium locations, if they meet the statutory requirements.
To meet this requirement, the successful claimant must:
a.	For mining claims, demonstrate a physical exposure of a valuable (commercial)
mineral deposit (the discovery) as defined by meeting the Department's Prudent Man
Rule1 and Marketability Test2
b.	For mill sites, show proper use or occupancy for uses to support a mining operation
and be located on non-mineral land.
c.	Have clear title to the mining claim (lode or placer) or mill site.
1	Where minerals have been found and the evidence is of such a character that a person of ordinary
prudence would be justified in the further expenditure of his labor and means, with a reasonable prospect
of success, in developing a valuable mine, the requirements of the statute have been met.
2	A mineral locator or applicant, to justify his possession must show by reason of accessibility, bona fides
in development, proximity to market, existence of present demand, and other factors, the deposit is of
such value that it can be mined, removed, and disposed of at a profit.
AVI-11

-------
d.	Have assessment work and/or maintenance fees current and performed at least $500
worth of improvements (not labor) for each claim (not required for mill sites).
e.	Meet the requirements of the Department's regulations for mineral patenting as
shown in the Code of Federal Regulations at 43 CFR 3861, 3862, 3863, and 3864.
f.	Pay the required processing fees and purchase price for the land applied for.
The BLM administers this program through its 12 State Offices and the Headquarters
office. The program has two essential components, adjudication and mineral
examination. A staff of land law examiners in each State Office adjudicates applications
for completeness and compliance with the law and regulations. All aspects, except the
mineral examination, are handled here. Once the application has successfully passed
through the adjudication process, the case is assigned to the BLM field office for a formal
mineral examination to verify the discovery of a valuable (commercially viable) mineral
deposit on the mining claims and proper use or occupancy for any mill sites. If the
Agency's mineral report confirms the discovery of a valuable mineral deposit and/or
proper use and occupancy for any associated mill sites, BLM will send the application to
the Secretary of the Interior for final review and action. If the applicant is successful on
all points, BLM issues a mineral patent for the land applied for. However, since October
1, 1994, Congress has imposed a budget moratorium on BLM acceptance of any new
mineral patent applications. Until the moratorium is lifted, the BLM will not accept any
new applications.
BLM is attempting to identify, prioritize, and take appropriate actions on those historic mine sites
that pose safety risks to the public or present serious threats to the environment. Using the
approach outlined in the Interdepartmental Abandoned Mine Lands Watershed Initiative, BLM
will work in partnership with EPA, state agencies, tribes, private parties, and other interested
groups to accelerate the rate of cleanup of watersheds affected by abandoned hard rock mines.
With special emphasis on ensuring that viable responsible parties contribute their share of
cleanup costs, federal land managers will add three to five watersheds or major mine cleanup
actions to the program each year from 1999 through 2005. Within the selected watersheds,
cooperative efforts and available resources will be concentrated first on AML sites and features
causing serious environmental impacts, then on mitigation and removal of physical safety
hazards.
National Park Service
The NPS operates under authority of the 1916 National Park Service Organic Act (16 USC 1, et
seqj as well as host of other federal statutes. According to U.S. NPS Policy Manual (2000)
mineral exploration and development may be allowed in parks only when prospective operators
demonstrate that they hold rights to valid mining claims, federal mineral leases, or non-federally-
owned minerals. If this right is not clearly demonstrated, the National Park Service will inform
the prospective operator that, until proof of a property right is shown, the Service will not further
consider the proposed activity. If the Service determines that the proposed mineral development
would impair park resources, values, or purposes, or does not meet approval standards under
applicable NPS regulations and cannot be sufficiently modified to meet those standards, the
Service will seek to extinguish the associated mineral right through acquisition, unless otherwise
directed by Congress.
AVI-12

-------
In some parks, all or certain types of mineral development are specifically prohibited by law.
Persons may not use or occupy surface lands in a park for purposes of removing minerals outside
the park unless provided for in law. General management plans, land protection plans, and other
planning documents for parks with mining claims, federal mineral leases, or non-federally-owned
mineral interests will address these non-federal property interests as appropriate. Lands with
mineral interests will be zoned according to their anticipated management and use, based on their
resource values, park management objectives, and park-specific legislative provisions relating to
mineral interests. The location of new mining claims pursuant to the General Mining Act of 1872
is prohibited in all park areas.
NPS has its own AML program and is an active participant with broader interdepartmental and
national AML program associations. The goals of the program are an inventory of all abandoned
mineral land sites in the NPS, the elimination of public safety hazards in such sites, the
elimination or reduction of adverse effects from such sites on resources in the parks, education
and awareness of the public from the preservation and interpretation of historic and cultural
artifacts, and the maintenance of specific abandoned mineral lands for critical wildlife habitat,
particularly for threatened and endangered species. Remediation of AML sites on NPS lands is an
ongoing effort and its focus has been on above-ground sites and remediation.
National Forest Service
The NFS was established in 1905 and is an agency of the USDA. The Transfer Act of 1905 (16
U.S.C. § 472, 476, 495, 551, 554, 615(b), et seq.) transferred administration of the forest reserves
to the Department of Agriculture under the Bureau of Forestry, which became the Forest Service.
The forest reserves were subsequently renamed national forests. The NFS manages public lands
in national forests and grasslands, which encompass 193 million acres. The mission of the FS is
to sustain the health, diversity, and productivity of the Nation's forests and grasslands to meet the
needs of present and future generations. Exploration, development, and production of mineral and
energy resources and reclamation of activities are part of the Forest Service ecosystem
management responsibility. All NFS lands which (1) were formerly public domain lands subject
to location and entry under the U.S. mining laws, (2) have not been appropriated, withdrawn, or
segregated from location and entry, and (3) have been or may be shown to be mineral lands, are
open to prospecting for locatable, or hardrock, minerals (16 U.S.C. 482). Claims are filed and
processed by agreement by the BLM.
The NFS established its combined Environmental Compliance and Protection (ECAP) and
Abandoned Mine Lands (AML) programs to reclaim the several thousand abandoned
underground and open-pit hard rock, placer, and coal mine sites and related mine and mill waste
sites on NFS lands that are causing damage to the environment or risks to public health and
safety. The NFS began receiving funds to clean up abandoned mines and other sites contaminated
with hazardous materials following the passage of CERCLA. Current funding for AML
remediation resulted from an agreement among the NFS, EPA, and the states to focus resources
on cleaning up abandoned mines using the watershed ("basin-wide") approach rather than
attempting to place each mine site under an individual NPDES water discharge permit. In 1995,
USDA and the NFS set an AML program goal: To reclaim by the year 2045 all abandoned mine
sites on National Forest System lands that have the potential to release hazardous substances or
sediment.
AVI-13

-------
Tribes
Uranium mines were produced on lands of many western Tribes. Principal among them are the
Navajo of Arizona and New Mexico, which had the most mines produced of any Tribe. The
largest uranium mine in the U.S., the Jackpile Mine, was operated on lands of the Laguna Pueblo
in New Mexico. The Spokane Tribe in Washington state had a uranium mill and mines on their
land, including the Midnite Mine which is now an EPA Superfund site. Others whose lands
hosted uranium mine operations include several Tribes of the Sioux of South Dakota, Hopi in
Arizona, Yavapai-Apache in Arizona, Eastern Shoshone and Northern Arapaho in Wyoming, and
Ute Tribes in Colorado and Utah. All of these Indian Tribes have had very specific
environmental, health, and other concerns related to uranium production facilities on their lands.
As a result of the large number of uranium mines on their Reservation, specialized governmental
agencies were created by the Navajo Nation to deal with reclamation and remediation activities,
as well as environmental protection on their Tribal lands. Due to that level of effort, the following
section provides a brief discussion of their organization.
Navajo Nation
The Navajo Nation occupies approximately 25,000 square miles of land in the Four Corners area
of Arizona, New Mexico, Utah, and California. The Navajo AMLRP/Uranium Mill Tailings
Reclamation Act Department, within the Navajo Nation Division of Natural Resources, has the
authority and responsibility to reclaim abandoned uranium mines. The program operates in
coordination with the U.S. Office of Surface Mining, within the jurisdiction of the Navajo Nation
pursuant to SMCRA, and the approved Navajo Reclamation Plan and Code.
The Navajo Abandoned Mine Lands Reclamation Program (NAMLRP) identified more than
1,032 abandoned uranium mine sites. As of 2005, 913 sites have been reclaimed. This Navajo
agency is also responsible for reclamation and administration of uranium mill sites on Navajo
lands under DOE UMTRCA program. To guide cleanup actions NAMLRP developed the Health
Physics and Instrumentation Monitoring Plan. The plan specifies that the ALARA principal has
been adopted such that every attempt will be made to prevent or minimize project related
radiation exposure to the general public.
In 1995, legislation made the NNEPA a separate regulatory branch of the Navajo National
government and charged it with protecting human health, welfare, and the environment of the
Navajo Nation. In April of that year, the Navajo Nation Council passed a resolution establishing
the NNEPA and approved adoption of the Navajo Nation Environmental Policy Act. This Act
provides guidance for the NNEPA in addition to recognizing that a clean environment contributes
to maintaining harmony and balance on the Navajo Nation. The mission of the NNEPA is as
follows: 'With respect for Dine' values, protect, preserve, and enhance public health, welfare and
the environment for present and future generations by developing, implementing, and enforcing
strong environmental laws; to foster public awareness and cooperation through education and
motivation." Numerous departments in the NNEPA are responsible for the environmental
protection programs across Tribal lands, including radiation protection, disposition of hazardous
wastes including those from uranium mines, and protection of water resources.
The U.S. EPA headquarters and Region IX offices have provided assistance as part of the
Agency's trust responsibilities to the Navajo Nation concerning uranium mine remediation and
other related radiation hazards.
AVI-14

-------
States
State authority to regulate radioactive materials is based on the Constitutional law tenet that any
authority or responsibility not specifically assigned to the federal government may be exercised
by the states. Many states actively regulate radioactive material through radiation control and
other state programs. Control under state law includes naturally occurring and accelerator-
produced radioactive materials and other sources of ionizing radiation. As of January 2006,
thirty-three states have entered into agreements with the NRC, under which the Commission has
delegated regulatory authority over most radioactive materials used in non-federal facilities, as
long as the state program is compatible with NRC requirements. Most states also control
radioactivity through programs implementing the federal clean air, clean water and other
environmental laws authorized by EPA.
A model state radiation control statute, last amended in 1983, has been developed by the Council
of State Governments. A comprehensive model state code for all types of radioactivity-containing
material and radiation-producing machines has been developed by the CRCPD. For example,
Part N of the Suggested State Regulations for Control of Radiation (SSRCR) is specific to
TENORM.
As an example from one of the 33 members of the Organization of Agreement States, the
Colorado Radiation Control Act designates a state radiation control agency and grants board
authority to evaluate and control "...hazards associated with the use of any and all radioactive
materials and other sources of ionizing radiation." In the Colorado Act radioactive material means
any material, solid, liquid or gas, which emits ionizing radiation spontaneously. Ionizing radiation
means gamma rays and x-ray and alpha particles, beta particles, high-speed electrons, neutrons,
protons, and other high-speed nuclear particles. The Colorado Act requires the Colorado Board of
Health to promulgate regulations (for licenses and for exemption from licensing), which are
modeled after those proposed by the Conference of Radiation Control Program Directors.
Colorado regulates uranium mining, milling, and mill tailings impoundments within its borders.
Whether or not an individual state has assumed regulatory authority from the NRC under an
Agreement, each state has explicit statutory authority for regulating sources of ionizing radiation
not otherwise regulated by the federal government. Several non-Agreement states (for example,
Michigan and New Jersey) have asserted specific authority over TENORM, especially cleanup
approaches and disposal. Thirteen have developed regulations specifically for TENORM. The
exercise of state authorities is reasonably consistent nationwide, but does vary in some respects.
For example, Colorado's statute requires Colorado's rules to be neither more nor less stringent
than the CRCPD SSRCR and also authorizes TENORM rules only after their promulgation by the
EPA. By contrast, the Illinois Division of Nuclear Safety, now under the Illinois Emergency
Management Agency, has no such constraints. Agreement State regulation of AEA materials is to
be uniform, consistent, and compatible with that of the NRC.
AVI-15

-------