Municipal Solid Waste Generation,
Recycling, and Disposal in the United
States: Facts and Figures
A Methodology Document
April 2014
U.S. Environmental Protection Agency
Office of Resource Conservation and Recovery
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Contents
INTRODUCTION 1
MAJOR APPLIANCES 2
Summary 2
Data Gaps 3
SMALL APPLIANCES 5
Summary 5
Data Gaps 6
FURNITURE AND FURNISHINGS 8
Summary 8
Data Gaps 10
CARPET AND RUGS 11
Summary 11
Data Gaps 12
BATTERIES, LEAD-ACID 14
Summary 14
Data Gaps 15
CONSUMER ELECTRONICS 17
Summary 17
Data Gaps 19
PAPER AND PAPERBOARD 20
Summary 20
Data Gaps 21
GLASS CONTAINERS AND PACKAGING 23
Summary 23
Data Gaps 24
STEEL CONTAINERS AND PACKAGING 26
Summary 26
Data Gaps 27
ALUMINUM CONTAINERS AND PACKAGING 29
Summary 29
Data Gaps 30
PLASTICS PRODUCTS 31
Summary 31
Data Gaps 32
WOOD PACKAGING 34
Summary 34
Data Gaps 36
FOOD WASTE 38
Summary 38
Data Gaps 39
YARD TRIMMINGS 41
Summary 41
Data Gaps 42
SCRAP TIRES 44
Summary 44
Data Gaps 46
ii
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
INTRODUCTION
This methodology document provides detailed methodology descriptions for selected
products to supplement the information found in EPA's Municipal Solid Waste in the United
States Facts and Figures report series. The products included in this document are:
Major Appliances Steel Containers and Packaging
Small Appliances Aluminum Containers and Packaging
Furniture and Furnishings Plastic Products
Carpet and Rugs Wood Packaging
Batteries, Lead-Acid Food Waste
Consumer Electronics Yard Trimmings
Paper and Paperboard Scrap Tires
Glass Containers and Packaging
The methodology for estimating generation, recovery, and discards are described
separately. For each product, a brief discussion, a flow diagram, and major data gaps are
included.
The material flows methodology used for making generation estimates is based on
production data for the materials and products in the municipal solid waste (MSW) stream.
Adjustments are made for imports and exports and for diversions from MSW. Adjustments are
also made for the lifetimes of products. Food wastes and yard trimming generation are accounted
for by compiling data from a variety of waste sampling studies.
Industry data and state level data provide the basis for recovery through recycling and
composting. Discards is the calculated difference between generation and recovery through
recycling and composting.
1
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
MAJOR APPLIANCES
Summary
Major appliances consist of many different types, sizes, and styles. Major appliances
include: clothes washers and dryers, dishwashers, freezers, microwave ovens, ranges (built-in,
free-standing, and surface types), refrigerators, room air conditioners, water heaters, and trash
compactors.
The primary source of data on annual shipments of major appliances is projected data
from Canon Communications in Annual Appliance Industry Forecasts. Unit weight and material
composition data for major appliances are based on government and industry studies. Recovery
rates for ferrous (steel) from major appliances were based on data from the Steel Recycling
Institute.
Major appliances are categorized as durables, with an estimated average useful life of
eight to 25 years. The life span differs from appliance to appliance. In the material flows
methodology, generation of major appliances is based on shipment figures, adjusted for the
individual life span of each appliance. Therefore, current year generation is based on a rolling
average of previous year's shipments. For example, assuming a 10 to 25 year life span for a
refrigerator, a rolling average of shipments between 1986 and 2001 is the basis for 2011
generation of refrigerators into the waste stream.
Unit weights for each type of appliance are determined by using the averaged weights of
most of the different sizes available. Steel is the predominant material comprising major
appliances, accounting for approximately 70 percent of total generation. Other materials found in
appliances in varying amounts include copper and brass, aluminum, glass, rubber, paperboard,
and plastics.
Currently, steel is the primary material recovered for recycling, although refrigerants (e.g.,
chlorofluorocarbons) in refrigerators and PCBs are removed from appliances and recovered but
not included in the material flow methodology. Due to the method of crushing appliances,
sometimes occurring with the crushing of damaged car bodies, it is difficult to extract other
materials for recycling.
2
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 1 is a flow chart illustrating estimates of generation, postconsumer recovery, and
discards of major appliance. Each block of the flow diagram contains a reference number, which
corresponds to the following remarks.
1. Total shipments (including net imports) of major household appliances = room air
conditioners + dishwashers + dryers + freezers + microwave ovens + ranges +
refrigerators + washers + water heaters + trash compactors.
2. Unit weight conversion factors, by material component, for major appliances
manufactured. Conversion factors based on retail and manufacturer websites and
various research studies.
3. Total shipments of major household appliances = individual appliance shipments
(1) x unit weight conversion factors, by material component, by appliance (2).
4. Temporary diversion based on estimated useful life for each major appliance. To
account for time lag, a rolling average range used to estimate tons discarded. For
example, assuming a 10 to 25 year life span for a refrigerator, a rolling average of
shipments between 1986 and 2001 is the basis for 2011 generation of refrigerators
into the waste stream. The appliances and useful life ranges are shown below.
Appliance
Temporary Diversion
Time Lag (years)
Air Conditioners, Room
10-20
Dishwashers
8-16
Dryers
15-21
Freezers
10-30
Microwave Ovens
8-16
Ranges
15-21
Refrigerators
10-25
Refrigerators Compact
3-7
Washers, Clothes
9-17
Water Heaters
9-17
Trash Compactors
8-12
5. Generation of major appliances = individual appliance shipments (3) adjusted for
temporary diversion based on useful life of appliance (4).
6. Recovery of steel from major appliances = generation of steel in all major
appliances (5) X recovery rate for appliances. Percentage recovery is provided by
the Steel Recycling Institute.
7. Discards of major appliances = generation - recovery of steel.
Data Gaps
Recovery of material other than steel is assumed to be zero.
Limited composition data.
3
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 1. Material Flow Methodology: Major Appliances
4
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
SMALL APPLIANCES
Summary
Small appliances consist of many different types, sizes, and styles. Examples of small
appliances include electric fans, coffee makers, electric irons, and food mixers. Shipment data for
some small appliances are only reported as "other" and includes similar, but different, small
appliances. For example, the U.S. Census Bureau combines drink makers, whippers, juicers,
grinders, ice crushers, and coffee grinders into a single category. Aluminum and plastic are the
predominant materials used in small appliances.
The primary source of data on annual shipments of small appliances is from the U. S.
Department of Commerce, Census Bureau and annual appliance industry statistical reviews. Unit
weight and material composition data for small appliances are based on published shipped
weights from retail websites and personal communication with small appliance retailers and
repair shops. Recovery of small appliances for recycling is assumed to be negligible, except for
steel magnetically recovered at MSW combustion facilities and limited data on residential
recovery.
Small appliances are categorized as durables, with an estimated average useful life of four
to ten years. In the material flows methodology, generation of small appliances is based on
shipment figures, adjusted for product life span. Therefore, 2011 generation is based on a rolling
average of shipments between 2001 and 2007 (four to ten years prior).
Figure 2 is a flow chart illustrating estimates of generation, postconsumer recovery, and
discards of small appliances. Each block of the flow diagram contains a reference number, which
corresponds to the following remarks.
1. Total shipments of small appliances = electric fans + broilers + coffee makers +
deep fat fryers + toaster ovens + waffle irons/griddles + frying pans/skillets +
airspace heaters + electric irons + electric bed coverings + electric heating pads +
portable humidifiers + food mixers + blenders + food processors + vacuums,
others.
2. Net Imports of small appliances = imports - export.
3. Total apparent consumption of small appliances = individual appliance shipments
(1) + net imports of small appliances (2)
5
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
4. Unit weight conversion factors, by material component, for small appliances
manufactured. Used to convert apparent unit consumption to tonnage.
5. Temporary diversion based on estimated useful life for each small appliance. To
account for time lag of four to ten years, a rolling average range used to estimate
tons generated.
6. Generation of small appliances = individual appliance shipments (3) adjusted for
temporary diversion based on useful life of appliance (5).
7. Recovery assumption that steel in small appliances is recovered for recycling
through magnetic separation at combustion facilities. Additional tonnage
estimated collected through curbside and drop-off programs by the Steel
Recycling Institute.
8. Discards of small appliances = generation - recovery of small appliances.
Data Gaps
Limited composition data.
Recovery of material other than steel is assumed to be zero.
U.S. Department of Commerce, Census Bureau. Current Industrial Reports
discontinued in 2011. This is a critical source of data.
6
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 2. Material Flow Methodology: Small Appliances
7
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
FURNITURE AND FURNISHINGS
Summary
Furniture and furnishings are comprised primarily of household and office furniture.
Materials consumed in manufacturing furniture and furnishings include wood, steel, textile,
plastic, glass, aluminum, and rubber and leather. Wood and steel are the primary materials,
accounting for 58 percent of total furniture and furnishings generation.
Data on shipment values of furniture and furnishings are provided by the Department of
Commerce in dollars. First, the ratio of the current year shipment values to the previous year
shipment value is determined (expressed as constant dollars). This ratio is then applied to the
previous year shipment tonnage. Adjustments are made for imports and exports and adjustments
are made for the lifetimes of the furniture.
Consumption of materials in manufacturing furniture and furnishings is calculated by
multiplying the reported consumption of material by the appropriate weight conversion factor.
For furniture and furnishings not reporting materials consumed in manufacturing, the value of
shipments is used as the basis for estimating quantities of material consumed. Adjustments are
then made to account for imports and exports, and conversion losses during manufacturing. The
primary sources of data are the Census of Manufacturers and Annual Survey of Manufacturers.
Furniture and furnishings are categorized as durable products, with an estimated average
useful life of 10 to 20 years for all furniture and furnishings. In the material flows methodology,
generation of furniture and furnishings is based on shipment figures, adjusted for the average 10
to 20 year life span. Therefore, the rolling average of 1991 to 2001 shipments is the basis for
2011 generation of furniture and furnishings into the waste stream. Generation of furniture and
furnishings represents products at the end-of-life (after primary use and reuse by secondary
owners).
Recovery of furniture and furnishings for recycling is assumed to be insignificant. Actual
recovery for remanufacture of either furniture or other products is generally not feasible due to
the difficulty in removing wood finishes and stains on the wood. Metal furniture, and in
particular, office furniture, may be recovered as steel scrap, however, this amount appears to be
8
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
quite small at this time. The only recovery of materials from furniture identified was mattress
recovery.
Figure 3 shows flow charts illustrating estimates of material discards from furniture and
furnishings. Each block of the diagram contains a reference number corresponding to the
following remarks.
1. Value of furniture shipments.
2. Conversion factors. This is the percent change of shipment value from previous
year.
3. Materials consumed in furniture = previous year material tonnage X conversion
factors (2). The percent change per year of annual value of shipments is applied to
previous year shipments of individual materials used in furniture and furnishings.
4. Net import adjustment factor = (value of shipments (1) + imports - exports)
divided by value of shipments (1).
5. Net imports of furniture = Net imports factor (4) x consumption (3).
6. Consumption of material in furniture = net imports of furniture (5) + domestic
consumption of materials in furniture and furnishings (3).
7. Conversion loss factors of furniture for textiles, steel, aluminum, rubber, glass,
and plastics.
8. Conversion losses for furniture = conversion loss factors (7) x consumption of
material (6).
9. Adjusted consumption of furniture = domestic consumption of materials (6) -
conversion losses (8).
10. Temporary diversion for furniture. Note: Average service life for furniture and
furnishers assumed to be from 10 to 20 years.
11. Generation of furniture = adjusted consumption of furniture (9) - temporary
diversion of furniture (10). Note: Generation for given year based on annual
average apparent consumption for a 10 year period, starting 20 years previous
(i.e., 10 year rolling average lagged 10 years).
12. Recovery of furniture
13. Discards of furniture = Generation of furniture (11) - recovery of furniture (12).
9
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Data Gaps
Material consumption data are no longer available; a new data source has not been
identified. This is a critical data gap. Without material consumption data, value of
shipments is used as a surrogate for increasing/decreasing furniture and furnishing
generation.
Current data on furniture life span unavailable.
Figure 3. Material Flow Methodology: Furniture and Furnishings
Figure 3. Material Flow Methodology: Furniture and Furnishings (Continued)
10
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
CARPET AND RUGS
Summary
There are many different types of carpets and rugs. Carpets and rugs are categorized as
woven, tufted, and other rugs (e.g., knitted, needle punched, braided). Plastic padding/underlay
used with carpets and rugs is also included. Tufted carpet is the largest category, accounting for
over 90 percent of total carpet and rug generation. Not included as MSW carpets and rugs are
those generated from transportation industries such as vehicle and aviation.
The primary source of data on carpets and rugs is the U.S. Department of Commerce
Current Industrial Report for Carpets and Rugs (MA314Q) and the International Trade
Commission online database of imports and exports. Shipment data are reported in million
square yards and converted to weight based on published conversion factors for the various
components comprising carpets and rugs. The primary components of carpets and rugs are fiber,
adhesives, and the backing. Fibers are categorized as a textile, adhesives as rubber, and the
backing primarily as plastic. Padding and underlay are also categorized as plastic.
Carpets and rugs are categorized as durables, with an estimated average useful life of five
to 15 years. In the material flows methodology, generation of carpets and rugs is based on
shipment figures, adjusted for temporary diversion of carpets and rugs. Therefore, current year
generation is based on a rolling average of previous year's shipments.
Figure 11 is a flow chart illustrating estimates of generation, postconsumer recovery, and
discards of carpets and rugs. Each block of the flow diagram contains a reference number, which
corresponds to the following remarks.
1. Total shipments of carpets and rugs = woven carpet and rugs + tufted carpet and
rugs + other carpet and rugs.
2. Total exports of carpets and rugs = woven carpet and rugs + tufted carpet and rugs
+ mother carpet and rugs.
3. Total imports of carpets and rugs = woven carpet and rugs + tufted carpet and rugs
+ other carpet and rugs.
4. Total apparent consumption of carpets and rugs = shipments + imports - exports.
Note: carpets and rugs are temporarily diverted from the waste stream based on a
11
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
useful life of five to 15 years; therefore current year apparent consumption is not
the actual amount of carpets and rugs discarded in current year.
5. Average weight per square yard of carpets and rugs, by material component, for
carpets and rugs manufactured = fiber (1.97 lbs per square yard), adhesives (1.72
lbs per square yard), and backing (0.52 lbs per square yard).
6. Padding and underlay for carpets and rugs (tons shipped per year).
7. Total apparent consumption of carpets and rugs = apparent consumption of
individual carpet and rug type (4) converted to weight measurement (5) +
padding/underlay for carpets and rugs (6).
8. Temporary diversion based on estimated useful life for carpets and rugs; assumed
5 to 15 years useful life.
9. Generation of carpets and rugs = apparent consumption of individual carpets and
rugs adjusted for temporary diversion based useful life. Note: Average service life
for carpets and rugs assumed to be from 5 to 15 years. Generation for given year
based on average annual shipments for 10 year period, starting 5 years previous
(i.e., 10 year rolling average lagged 5 years).
10. C&D (construction & demolition) Carpet and Rug Generation. Generation
reduced by 10 percent (assuming disposed of as C&D waste).
11. Generation of carpets and rugs classified as municipal solid waste = total
generation of carpets and rugs (9) - carpets and rugs classified as construction and
demolition waste (10).
12. Carpet and rug fibers and padding/underlay recovered for recycling.
13. Discards of carpets and rugs classified as municipal solid waste = generation of
carpets and rugs classified as municipal solid waste (11) - recovery of carpet and
rug fibers and padding/underlay (12).
Data Gaps
U.S. Department of Commerce has discontinued the Current Industrial Report
series for all products including carpet and rugs.
Assumption that 10 percent of generation is through the C&D waste streams
needs further research.
12
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 4. Material Flow Methodology: Carpets and Rugs
13
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
BATTERIES, LEAD-ACID
Summary
Lead-acid vehicle batteries for cars, trucks, and motorcycles are considered in the
material flow methodology. Other batteries used in applications such as aircraft and military
vehicles, boats, heavy-duty trucks and tractors, are not included in the material flows
methodology.
Lead-acid batteries have three major components, which are lead, the plastic
polypropylene case, and other materials including battery fluids. Lead accounts for approximately
48 percent of total vehicle battery generation, plastic cases 6 percent, and the remaining 46
percent is comprised of other materials in the battery, including fluids.
The primary source of data for lead-acid batteries is the Battery Council International and
U.S. Census Bureau, and the National Automobile Dealers Association (NADA).
Generation of vehicle batteries is determined based on replacement battery purchases,
including imported batteries, and the number of vehicles deregistered annually. Unit weight
conversion factors for lead in batteries and plastic cases for each type of battery are used to
calculate battery generation. Recovery of batteries has been consistently high due to a well
established recovery system. For the material flows methodology it is assumed that the lead,
plastic cases, and other materials in the battery are all recovered at the same rate.
Figure 5 is a flow chart illustrating estimates of lead, plastic, and other material discards
from vehicle batteries. Each block of the diagram contains a reference number corresponding to
the following remarks.
1. Number of domestic vehicle replacement batteries sold (includes both car and
trucks). Assumption is that for every replacement battery sold, a used lead-acid
battery was generated.
2. Number of imported vehicle replacement batteries (includes cars and trucks).
Assuming 90 percent of total vehicle battery imports are used as replacement
batteries.
3. Number of deregistered cars and trucks. To determine the number of deregistered
cars separately from deregistered trucks, the number of total deregistered vehicles
14
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
was multiplied by the percent operational cars represented of total operational cars
and trucks. Assuming batteries in deregistered vehicles are no longer in use.
4. Number of domestic motorcycle replacement batteries calculated by dividing
motorcycle registrations by two. Assuming one battery is replaced for every two
motorcycles.
5. Number of deregistered motorcycle batteries is assumed to equal 25 percent of
motorcycle registrations.
6. Number of imported motorcycle replacement batteries. Assuming 90 percent of
total motorcycle battery imports are used as replacement batteries.
7. Lead in batteries. 22.3 pounds of lead per car battery. 38.7 pounds of lead per
truck battery; 4.8 pounds lead per motorcycle battery.
8. Total lead generation = lead/vehicle battery X number vehicles batteries + and
lead/motorcycle battery x number of motorcycle batteries.
9. Apparent consumption of plastic battery cases equals the number of batteries
generated (the sum of domestic and imported replacement batteries and
deregistered vehicles).
10. Plastic battery case conversion factor at 6 percent of total battery weight based on
manufacturer product specifications.
11. Plastic generation = number of batteries cases (9) x plastic per battery (10).
12. Other materials, including battery fluid, calculated by difference comprise 46
percent of battery weight.
13. Total generation of lead-acid batteries = generation of lead (8) + generation of
plastic battery cases (11) + generation of other materials in batteries (12).
14. Recovery. Total battery lead recovery data are available from both Battery
Council International and The Bureau of Mines. However, it is not possible to
determine how much of total recovered lead is from vehicle, truck, and
motorcycle lead-acid batteries. It is assumed that the recovery rate of these types
of lead-acid batteries is equal to recovery rate of total battery lead. It is also
assumed that the recovery rates for the plastic case and the other materials are the
same as lead.
15. Total discards of lead, plastic, and other materials = total generation of lead,
plastic, and other material - recovered lead, plastic, and other material.
Data Gaps
Motorcycle replacement battery and deregi strati on assumptions need to be
updated.
15
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 5. Material Flow Methodology: Batteries, Lead-Acid
16
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
CONSUMER ELECTRONICS
Summary
Consumer electronic products include electronic products used in residences and
commercial establishments such as businesses and institutions. Consumer electronics include
video and audio equipment and information products. Video products include standard
televisions (TV), projection TV, high density TV, liquid crystal display TV, VCR decks,
camcorders, laserdisc players, and digital versatile disc players (DVD). Audio products include
rack audio systems, compact audio systems, portable compact discs (CD), portable headset audio,
total CD players, and home radios. Information products include cordless/corded telephones,
mobile telephones, telephone answering machines, facsimile (fax) machines, personal computers,
computer printers, computer monitors, modems, and fax modems. Certain other electronic
products such as separate audio components are excluded because of data limitations.
Consumer electronic generation is estimated by calculating the annual apparent
consumption. Apparent consumption equals U.S. manufacturer shipments plus U.S. imports
minus U.S. exports. Consumer electronics are categorized as durables, with an estimated average
useful life of 3 to 23 years, depending on the product (see the table below). Therefore, current
year generation is based on a rolling average of previous year's shipments. The year in which a
particular electronic item enters the municipal solid waste stream is determined from the
estimated life span of the item. Average weights for consumer electronics were estimated after
collecting information from retail websites, consumer electronic magazines, and weighing
available items.
The generation methodology combines data from two sources for domestic shipments: (1)
The Consumer Electronics Association (CEA); and (2) the U.S. Department of Commerce trade
data. CEA data reflect shipments of consumer electronics to retail outlets. The U.S. Census
Bureau's Current Industrial Reports include trade data (shipments, imports, and exports) from
the U.S. Department of Commerce.
The methodology for estimating electronics recovery follows the methodology used in
the EPA report "Electronics Waste Management in the United States Through 2009" May 2011.
State level data collected from 31 state agency websites represented about 68 percent of the US
17
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
population in 2011. To fill in the two data gaps (1) states without data and (2) commercial
recovery missed from the states' reporting mechanism similar assumptions used in the May 2011
report were applied.
Per capita factors developed from available data applied to population in states without
data were used to estimate recovery in states where data were not identified.
The assumption to estimate the commercial recovery missed by the states' data collection
efforts is that commercial recovery accounts for 67 percent of total recovery. This assumption is
applied to the states' residential data to estimate commercial recovery (i.e., residential
recovery/,33 - residential recovery = commercial recovery).
Figure 6 is a flow chart illustrating estimates of consumer electronics discards. Each
block of the diagram contains a reference number corresponding to the following remarks.
1. Domestic shipments of consumer electronics.
2. Net imports of consumer electronics.
3. Apparent consumption of consumer electronics = domestic shipments of
consumer electronics (1) + net imports of consumer electronics (2).
4. Temporary diversion based on estimated useful life for consumer electronics.
Estimated Life of Selected Consumer Electronics (in year)
Temporary Diversion
Primary and Secondary Use
Video Products
Direct View Color TV
7-23
Projection TV
7-15
HDTV
7-23
LCD Color TV
9-15
Plasma
7-15
TV/VCR Combination
10 - 12
Videocassette Players
7-10
VCR Decks, DVD Players, Camcorders
7-10
Audio Products
Home and Portable Audio Products
3 - 15
Home Information Products
Mobile Telephones
3-7
Cordless/Corded Telephones
3-8
Telephone Answering Machines
3-8
Fax Machines
3-8
Personal Computers
3 - 18
Personal Computers Laptop
2-8
Computer Printers
4-14
Aftermarket Computer Monitors
5 - 13
Personal Computers Monitors - Flat panel
3 - 14
Keyboards
3-6
Mouse Devices
3-6
18
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
5. Generation of consumer electronics = apparent consumption of consumer
electronics adjusted for temporary diversion based useful life.
6. Recovery of consumer electronics.
7. Discards of consumer electronics = generation of consumer electronics (5) -
recovery of consumer electronics (6).
Data Gaps
Certain other electronic products such as separate audio components are excluded
because of data limitations.
Some newer electronic products such as GPS units and tablets have not been
added to the product list. Data availability is unknown.
Recovery data are not available for all states.
Most state agency accounting of recovery does not include recovery through the
commercial sector.
Figure 6. Material Flow Methodology: Consumer Electronics
19
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
PAPER AND PAPERBOARD
Summary
Collectively, the many products made of paper and paperboardi materials comprise the
largest component of MSW. The paper and paperboard materials category includes products such
as office papers, newspapers, corrugated boxes, milk cartons, tissue paper, and paper plates &
cups.
Estimates of paper and paperboard generation are based on statistics published by the
American Forest & Paper Association (AF&PA). These statistics include data on new supply
(production plus net imports) of the various paper and paperboard grades that go into the
products found in MSW. The AF&PA new supply statistics are adjusted to deduct converting
scrap, which is generated when sheets or rolls of paper or paperboard are cut to make products
such as envelopes or boxes. Converting scrap rates vary from product to product; the rates used
in this report were developed as part of a 1992 report for the Recycling Advisory Council, with a
few more revisions as new data became available. Various deductions also are made to account
for products diverted out of municipal solid waste, such as gypsum wallboard facings (classified
as construction and demolition debris) or toilet tissue (which goes to wastewater treatment
plants).
Estimates of recovery of paper and paperboard products for recycling are based on annual
reports of recovery published by AF&PA. The AF&PA reports include both post- and
preconsumer recovery of paper and paperboard purchased by U.S. paper mills, plus exports of
recovered paper, plus a relatively small amount estimated to have been used in other products
such as insulation and animal bedding. Adjustments are made to the recovery as reported by
AF&PA to remove preconsumer recovery from the postconsumer recovery estimate.
Figure 7 is a flow chart illustrating estimates of paper and paperboard discards. Each
block of the flow diagram contains a reference number, which corresponds to the following
remarks.
1. New supply of paper and board. Includes production for domestic use plus
imports minus exports. Includes office paper file diversion reentering the paper
supply.
20
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
2. Diversion of products. Includes office paper in files, magazines, books, and of
products not counted as MSW, e.g., construction paper and board, toilet tissue.
3. Converting scrap (non-MSW industrial scrap).
4. Unrecovered converting scrap.
5. Recovered converting scrap.
6. Generation of paper and board = new supply of paper and board (1) - converting
scrap - diversion of paper and board (2).
7. Adjustment for packaging of imported goods.
8. Adjusted generation = generation of paper and board (6) + adjustment for
packaging of imported goods (7).
9. Postconsumer recovery.
10. Total recovery of paper and board = postconsumer recovery (9) + recovered
preconsumer converting scrap (5).
11. Discards of paper and board = adjusted generation (8) - total Recovery of paper
and board (9).
Data Gaps
Current data for adjustments for packaging of imported goods are not available.
Current data on adjustment for converting scrap are not available.
21
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 7. Material Flow Methodology: Paper and Paperboard
22
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
GLASS CONTAINERS AND PACKAGING
Summary
Glass containers are comprised of beer and soft drink, wine and liquor, and food and
other containers. Beer and soft drink bottles account for 59 percent of total glass container
generation, wine and liquor containers 19 percent, and the remainder as other glass containers.
Glass container volumes of one gallon and less are included.
Generation of glass containers is calculated based on unit container weights and container
shipments. The primary source of domestic glass container production data is the Glass
Packaging Institute. Until 2009, domestic production data was obtained from the U.S. Census
Bureau Current Industrial Report series for glass containers. The source of import and export
data is the U.S. International Trade Commission's online trade database. Glass container
recovery is estimated from the combination of two data sources. First the Glass Packaging
Institute provides the quantity of glass recovered for glass container recovery and then state
environmental agency websites are researched for state level recycling data (including data from
bottle bill states). The difference between the two data sources is assumed to equal the quantity
of recovered glass going to low-end markets such as construction aggregate.
Figure 8 show flow charts illustrating estimates of material discards from glass containers
and packaging. Each block of the diagram contains a reference number corresponding to the
following remarks.
1. Shipments of empty glass containers by container type. Data do not represent total
industry. To adjust upward, factors were developed by comparing 2008 Census
data to 2008 GPI data and applied to beer and three categories of other containers.
2. Glass container unit weights (thousand gross) = weight of domestic production of
glass container (pounds) divided by domestic production of glass containers
(gross).
3. Domestic shipment weight = containers shipped (1) x conversion factor (2).
4. Net imports (imports - exports) of glass containers filled with product. Includes
glass containers for wine, liquor, and beer.
5. Import glass container unit weight conversion factors. Liquid measurements
converted to gross of bottles represented by volume x weight per gross of bottles.
23
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
6. Net import of filled glass containers = net imports (4) x unit weight conversion
factors (5).
7. Net imports (imports - exports) of empty glass containers.
8. Glass container unit weights (thousand gross) = weight of domestic production of
glass container (pounds) divided by domestic production of glass containers
(gross). Assumed same conversion factors for imported empty containers.
9. Net imported empty glass containers = containers (7) x conversion factors (8).
10. Generation of glass containers = domestic shipments glass containers (3)+ imports
of glass containers (6) + imports of empty glass containers (9).
11. Recovery of glass containers.
12. Discards of glass containers = generation of glass containers (10) - recovery of
glass containers (11).
Data Gaps
Domestic shipment data do not represent total industry.
Missing imports of food and other products in glass containers. Imports of alcohol
beverages are included.
State level recovery data could include recovered bottles imported into one state
from another state resulting in double counting.
24
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 8. Material Flow Methodology: Glass Containers and Packaging
25
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
STEEL CONTAINERS AND PACKAGING
Summary
Steel containers and packaging is comprised of cans and other containers and packaging.
Cans are categorized as food and nonfood cans. Other steel containers and packaging includes
items such as barrels, drums, shipping pails, crowns, and strapping. Food and nonfood cans is the
largest category comprising steel containers and packaging, accounting for over 80 percent of
total generation.
Generation of steel cans for food and other types of cans is calculated based on
consumption of tin plate and tin free steel by domestic can makers less conversion losses during
the production of cans. The primary source of this information is the American Iron and Steel
Institute (A1SI) annual report. Quantities of steel cans recovered are based on recovery rates
determined by the Steel Recycling Institute.
Generation of other (barrels, drums, pails and all other packaging) steel containers and
packaging is based on domestic shipment data compiled by the American Iron and Steel Institute.
Similar to can production, AISI statistics on various steel grades into container, packaging, and
shipping markets (adjusted for non-MSW markets such as the automobile industry) are used to
estimate other steel containers and packaging. Recovery rates for other steel containers and
packaging are based on estimates provided by the Steel Recycling Institute.
Figure 9 is a flow chart illustrating estimates of generation, postconsumer recovery, and
discards of steel containers and packaging. Each block of the flow diagram contains a reference
number, which corresponds to the following remarks.
1. Domestic shipments of tin plate and tin free steel to can makers.
2. Imports of tin plate and tin-free steel to can makers = percent of total domestic
shipments of tin plate and tin free steel that is shipped to can makers x total
imports of tin plate and tin free steel. Assumes that the percent of total imported
tin plate and tin free steel that is shipped to can makers is equal to the percent of
total domestic shipments of tin plate and tin free steel that is shipped to can
makers.
26
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
3. Domestic consumption of tin plate and tin free steel by can makers = domestic
shipments of tin plate and tin free steel to can makers (1) + imports of tin plate
and tin free steel to can makers (2).
4. Conversion loss (prompt scrap). Conversion = domestic consumption of tin plate
and tin free steel by can makers x conversion loss factor of 12.5 percent.
5. Total steel in cans produced by can makers = domestic consumption of tin plate
and tin free steel (3) - conversion loss (4).
6. Loss of cans by product filler = total steel in cans produced by can makers (5) x
loss of cans by product filler (1 percent).
7. Generation of steel in steel food and other cans = total steel in steel cans produced
(5) - loss of cans by product filler (6).
8. Recovery of steel food and other cans = industry recovery rate of steel cans x
generation of steel in steel food and other cans (7).
9. Discards of steel cans = steel beverage can generation (7) - steel beverage can
recovery (8).
10. Domestic shipments of steel barrels, drums, shipping pails, and other steel
packaging estimated from black plate and tin-coated sheet sold into container,
packaging, and shipping markets.
11. Conversion loss = domestic shipments of steel barrels, drum, shipping pails, and
other steel packaging (10) x conversion loss factor (12.5 percent).
12. Generation of steel barrels, drums, shipping pails, and other steel packaging =
domestic shipments (10) - converting losses (11).
13. Recovery of steel barrels, drums, shipping pails, and other steel packaging =
industry recovery rate of steel barrels, drums, and shipping pails and other steel
packaging x generation of steel barrels, drums, shipping pails, and other steel
packaging (12).
14. Discards of steel barrels, drums, shipping pails, and other steel packaging =
generation of steel barrels, drums, shipping pails, and other steel packaging (12) -
recovery of steel barrels, drums, shipping pails, and other steel packaging (13).
Data Gaps
Scrap loss for barrels, drums, and shipping pails assumed to be the same as steel
cans.
27
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 9. Material Flow Methodology: Steel Containers and Packaging
28
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
ALUMINUM CONTAINERS AND PACKAGING
Summary
Aluminum containers and packaging is comprised of cans and other containers and
packaging. Cans are categorized as beverage cans (soft drink and beer), or food and other
nonfood cans. Other aluminum containers and packaging includes items such as foil, closures,
and aluminum lids. Beverage cans is the largest category of aluminum containers and packaging,
accounting for over 70 percent of total generation.
Generation of aluminum cans is calculated based on unit can weights and can shipments.
The primary source of aluminum container and packaging generation and recovery data is The
Aluminum Association. Generation of aluminum foil for containers and packaging is also based
on data from the Aluminum Association. Generation of closures is estimated at less than 1
percent of foil based on a discontinued data series from a Current Industrial Report of the U.S.
Census Bureau.
Figure 10 is a flow chart illustrating estimates of generation, postconsumer recovery, and
discards of aluminum containers and packaging. Each block of the flow diagram contains a
reference number, which corresponds to the following remarks.
1. Total domestic aluminum consumption. This includes net imports (imports -
exports) based on data from Aluminum Association.
2. Conversion factor: 28.93 lbs/1,000 cans (2011). Conversion factor has decreased
over time as cans are lightweighted.
3. Food and other cans = aluminum sheet and plate used for containers and
packaging minus sheet and plated used domestically for beverage cans adjusted
for 25 percent production scrap.
4. Shipments into household and institutional foil markets and foil used in semi-rigid
food containers. Assumes a 1 percent fabrication loss. Closures assumed at 2,000
tons.
5. Generation of Aluminum containers and packaging = beverage containers (1) +
food and other cans (3) + foil and closures (4).
6. Cans melted by domestic end users + exported used beverage containers (UBC) -
imported UBC. UBCs recovered from foreign sources and imported to the U.S. to
29
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
be melted to produce new cans by U.S. producers are not included in the U.S.
recovery estimates.
7. Discards = generation - recovery
Data Gaps
Only aluminum can recovery estimates are available; other aluminum packaging
recovery estimates are not available. Food and other cans and foil recovery
estimated at 0 percent based on Aluminum Association input.
Figure 10. Material Flow Methodology: Aluminum Containers and Packaging
30
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
PLASTICS PRODUCTS
Summary
Plastics have been one of the fastest growing components of municipal solid waste
(MSW) in recent years. Plastics are found in all three major MSW categories: durables,
nondurables, and containers and packaging.
The primary data source for plastics production data is published annually by the
American Chemistry Council in the Resin Review. The product line items in this annual report
provide the basis for allocating resin use to specific products. Plastics in the durable goods such
as appliances and lead-acid batteries and nondurable goods such as diapers and footwear are
estimated using other material flow methodologies. Those categories that have lifetimes of more
than one year are lagged; in other words have a temporary diversion before generation. There is
an adjustment for imports and exports, as well as fabrication losses, to estimate generation.
The primary sources of data on plastics recovery are annual industry sourced recovery
surveys. Two primary sources are the American Chemistry Council and the National Association
for PET Container Resources (NAPCOR).
Figure 11 is a flow chart illustrating estimates of generation, postconsumer recovery, and
discards of plastics in MSW products. Each block of the flow diagram contains a reference
number, which corresponds to the following remarks.
1. Domestic production of plastics from recovered and virgin resin = durable plastic
products + nondurable plastics products + plastic containers and packaging. For
resin sales data that include sales to Canada, total sales reduced by ratio of
Canada/US population.
2. Net import adjustment factors for select products made with plastics = total net
imports value (imports - exports) divided by total domestic shipment values.
3. Net imports of plastics in select products = plastic used in select MSW products
(1) x net import adjustment factor (2).
4. Plastic resin used in MSW products = net imports of plastics in MSW products
(3) + recovered and virgin resin (1).
5. Fabrication scrap loss = plastic resin used in MSW products x 1 percent
fabrication scrap loss.
31
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
6. Apparent consumption of plastics in MSW products = plastic resin used in MSW
products (4) - fabrication scrap loss (5)
7. Temporary diversion for durable and non-durable plastic products. Based on
estimated useful life for durable and nondurable MSW products made with
plastics
8. Generation of plastics in MSW products = apparent consumption (6) adjusted for
temporary diversion for durable and nondurables (7) + generation of plastics in
other MSW products (9) such as appliances and lead-acid batteries.
9. Generation of plastics in other MSW products. Source: Material flow
methodologies for other MSW products (e.g., plastic from lead-acid batteries).
10. Recovery of plastics in MSW products. Includes separate recovery estimates for
durables, nondurables, and containers and packaging.
11. Discards of plastics in MSW products = generation of plastics in MSW products
(9) - recovery of plastics in MSW products (10)
Data Gaps
Net import adjustment generation factors for products made with plastics do not
cover all products; shipment values for some HTS/NAICS product codes are
missing. Therefore imports of some plastic products are not accounted for.
Recovery data for durable goods are limited.
Fabrication loss may be underestimated for some products.
32
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 11. Material Flow Methodology: Plastics Products
33
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
WOOD PACKAGING
Summary
Wood packaging includes reusable and expendable wood pallets and other wood
packaging. Other wood packaging includes crates, wooden containers, and dunnage. Pallets are
estimated to account over 90 percent of total wood packaging.
Generation of wood packaging is determined from the production of new pallets each
year. The primary source of new pallet production is the National Wooden Pallet and Container
Association and annual market research information from the Fredonia Group. The number of
pallets are converted to board foot and then to thousand tons.
Pallet Enterprise estimates the percentage of reusable versus expendable pallets produced.
The number of reuses each pallet can endure is also considered. Reusable pallets are assumed to
be reused four times per year. Reusable pallets weigh more and last longer than expendable
pallets. Reusable pallet loss due to normal use is assumed to be 15 percent per use. Expendable
pallets are assumed to be- discarded the year they are produced. Other wood packaging is
estimated to be 10 percent of the total generation of pallets.
Reuse of pallets is accounted for in generation and therefore, is not included in recovery
for recycling. Recovery of wood packaging includes recycling wood into compost, mulch, or
similar uses. Recovery of wood packaging for fuel is not, however, included with recovery for
recycling of wood packaging.
Figure 12 is a flow chart illustrating estimates of wood packaging production, generation,
recovery, and discards. Each block of the diagram contains a reference number corresponding to
the following remarks.
1. Total pallet production based on increase in demand from base year 2006.
2. Reusable pallet production (in units) = total pallet production (1) X percent of
total pallets that are reusable (2006 data).
3. Wood use in reusable pallet production = reusable pallet production (in units) (2)
X 17 board foot per pallet.
34
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
4. Reusable pallet new supply = reusable pallet new supply (in board feet) (3) X 55
pounds per board foot.
5. Reusable pallets remaining in use from previous year to current year. Reusable
pallets remaining in service equals previous year's total pallet in use less pallets
removed from service.
6. Refurbished reusable pallets returned to service from previous year to current
year. Assumes pallets refurbished in current year are returned to service the
following year.
7. Total reusable pallets in use = reusable pallets new supply (4) + reusable pallets
remaining from previous year (5) + reusable pallets refurbished and returned to
use from previous year (6).
8. Reusable pallets removed from service = 47.8 percent [the number of pallets
removed after a 15 percent loss during each of the four reuses in a year; (100 -
15%) x (100 - 15%) x (100 - 15%) x (100 - 15%)].
9. Total reusable pallet generation = reusable pallets in use (7) - reusable pallets
removed from service (8).
10. Expendable pallet production = total pallet production (1) - reusable pallet
production (2).
11. Expendable pallet generation = expendable pallet production (in units) (10) X 30
pounds per pallet.
12. Other wood packaging expressed as a percent of expendable pallet production.
Other wood packaging = Expendable pallet production (board feet) (10) X 20
percent.
13. Scrap loss = other wood packaging (12) X scrap loss factor (15 percent).
14. Other wood packaging generation = other wood packaging (12) - scrap loss (13).
15. Other wood packaging generation (in tons) = other wood packaging generation
(14) X (.0625 cubic feet per board foot X 22 pounds per cubic foot). This
calculation assumes that other wood packaging is constructed of soft wood.
16. Total wood packaging generation = reusable pallet generation (9) + expendable
pallet generation (11) + other wood packaging generation (15).
17. Wood packaging recovery. Total recovery numbers also include pallets processed
at landfills.
18. Wood packaging Discards = total wood packaging generation (20) - wood
packaging recovery (17).
35
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Data Gaps
Pallet production data is based on projected market growth instead of actual units
produced.
Current data on other wood packaging production are not available.
Current recovery and end-of-life management data are not available. Recovery
and end-of-life management trended from a 2009 article using 1999 though 2006
data.1
1 Robert J. Bush, Philip A. Araman. "Pallet Recovery, Repair and Remanufacturing in a Changing Industry: 1992 to
2006". August 2009. Pallet Enterprise.
36
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Total Pallet Production
(¦mutton Balls)
(1)
Scrap Lass
(13)
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
FOOD WASTE
Summary
Food waste consists of uneaten food and food preparation wastes from residences,
commercial establishments such as grocery stores and sit-down and fast food restaurants,
institutional sources such as school cafeterias, and industrial sources such as factory lunchrooms.
Preconsumer food waste generated during the manufacturing and packaging of food products is
considered industrial waste and therefore not included in MSW food waste estimates.
Food waste from residential and commercial sources is estimated using factors based on
data from sampling studies in various parts of the country in combination with demographic data
on population, grocery store sales, restaurant sales, numbers of employees, and numbers of
students, patients, and prisoners in institutions. The residential and commercial sourced factors
are reviewed and revised as more sampling studies become available.
Figure 13 is a flow chart illustrating estimates of generation, recovery, and discards of
food wastes. Each block of the flow diagram contains a reference number, which corresponds to
the following remarks.
1. Average residential food waste generation factor (lb per person per day). Data
range is from 0.16 to 0.67 pounds per person per day. This data range is from
curbside sampling in Arizona, California, Canada, Illinois, Minnesota, Missouri,
Vermont, Washington, Wisconsin. Lower end data from Minnesota and
Wisconsin; higher end data from Arizona and California.
2. Generation of residential food waste = average residential food waste factor (1) X
U.S. population.
3. Average commercial food waste generation factors. Generation factors developed
from sampling studies conducted in the following sectors: grocery stores,
restaurants, prisons, educational institutions, nursing homes and residential
hospitals, hotels, and employee cafeterias.
4. Generation of commercial food waste = average commercial food waste factors
(3) X appropriate demographic and economic statistics.
5. Total generation = residential food waste (2) + commercial food waste (4)
6. Recovery through food waste composting. Recovery estimated from state agency
data on food waste composted. See data gaps for further discussion.
38
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
2
7. Recovery through mixed MSW composting as tabulated by BioCycle.
8. Total recovery through composting = food waste composting (6) + mixed MSW
composting (7).
9. Discards = generation (5) - recovery (8).
Data Gaps
Number of
States Data Year
1 2008
7 2009
17 2010
8 2011
33 Total
Recovery through MSW composting includes non-food products and materials.
Some food waste may be collected with yard trimmings and not accounted for as
food waste recovery.
There may be some additional commercial and institutional sources of food waste
that are not accounted for due to the lack of available onsite sampling studies.
State agency reported food waste composted may include non-MSW food waste
from industrial sources including high volume food waste composting from
processors. Recovery data for food waste other than composting is not available
(e.g., food donations).
Latest available state agency reported food waste recovery through composing
data are used, therefore data year will vary. Methodology assumes food waste
composting is fairly constant (i.e., an established composting program continues
to operate, at a minimum, at the last reported level). For 2011, data were found for
33 states with the following data years
2 Latest data: Dan Sullivan. Mixed Waste Composting Facilities Review. Nationwide Survey. BioCycle. November
2011. Available online at: http://www.westwendovercity.com/.
39
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 13. Material Flow Methodology: Food Waste
40
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
YARD TRIMMINGS
Summary
Yard trimmings include grass, leaves, and tree and brush trimmings from residential,
institutional, and commercial sources. Yard trimmings do not include trees from these sources,
vegetative clearing by utility companies, or land clearing for development.
The definition of yard trimmings includes the amount that enters the solid waste
management system and does not include yard trimmings managed on-site through backyard
composting or mulching. Yard trimmings generation is based on a factor developed in 2006 from
data on yard trimming generation (in pounds per person per year) from all regions of the U.S.
applied to U.S. population from Census Bureau Current Population Reports.
While in past years generation of yard trimmings had been increasing steadily as
population and residential housing grew (i.e., constant generation on a per capita basis), in the
1990s local and state governments started enacting legislation that discouraged yard trimmings
disposal in landfills and encouraged source reduction. Legislation affecting yard trimmings
disposal in landfills was tabulated, using published sources. In 1992, 11 states and the District of
Columbia-accounting for more than 28 percent of the nation's population-had legislation in
effect that bans or discourages yard trimmings disposal in landfills. The tabulation of current
(2011) legislation shows 22 states representing about 40 percent of the nation's population have
legislation affecting disposal of yard trimmings. In addition, some local and regional jurisdictions
regulate disposal of yard trimmings. This has led to an increase in source reduction such as
backyard composting and the use of mulching mowers to allow grass trimmings to remain in
place since the early 1990's.
Recovery for composting of yard trimmings is estimated using information from state
composting programs. State reported composting tonnages may vary on a yearly basis with the
amount of storm debris composted. It should be noted that the estimated recovered yard
trimmings for composting does not include yard trimmings recovered for direct land spreading
disposal. It also should be noted that these recovery estimates do not account for source reduction
activities taking place onsite; the yard trimmings recovery estimates are based on material sent
off-site for management.
41
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 14 is a flow chart illustrating estimates of generation, recovery, and discards of
yard trimmings. Each block of the flow diagram contains a reference number, which corresponds
to the following remarks.
1. Generation of yard trimmings before source reduction = current U. S. population x
281 pounds per person per year (based on EPA funded data gathering in 2006).
2. Generation after source reduction. Assumed based on 50 percent reduction in
states affected by legislation and 40 percent of the US population affected by
legislation. 100% x 50% x 40% = 20%.
3. Recovery estimates compiled from states with yard trimmings legislation.
Recovery data gathered from state environmental agencies; 22 state environmental
websites researched for yard trimmings composting data.
4. Recovery in all states with yard trimmings legislation including states that do not
report data. States not reporting data were estimated from per capita rates in states
with data (3) that have legislation.
5. Recovery estimates compiled from states without yard trimmings legislation.
Recovery data gathered from state environmental agencies; 28 state and District of
Columbia environmental websites researched for yard trimmings composting data.
6. Recovery in all states without yard trimmings legislation including states that do
not report data. States not reporting data were estimated from per capita rates in
states with data (4) that do not have legislation.
7. Recovery reported as mulch. Data gathered from various state environmental
agencies.
8. Total Recovery = recovery in all states with yard trimmings legislation (4) +
recovery in all states without yard trimmings legislation (6) + recovery reported as
mulch.
9. Discards = generation (2) - total recovery (8).
Data Gaps
Source reduction is based on the assumption that legislation is the major driver.
This assumption is out dated. Many states and local governments aggressively
promote source reduction without legislation. Additionally, as states repeal yard
trimmings legislation, the impact on source reduction has not been researched.
Some states do not report data on composting programs. Developed per capita
recovery factors from states with data applied to population in states with no
reported data.
42
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
State agency recovery data may include storm debris data that are not accounted
for in the generation estimate.
State agency recovery data may include other non-yard trimming materials not
included in the generation estimate such as food waste.
Figure 14. Material Flow Methodology: Yard Trimmings
43
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
SCRAP TIRES
Summary
Used tires (scrap tires) from cars and trucks are considered in the material flows
methodology. Used tires from buses, heavy-duty tractor trucks, and farm and construction
equipment are not included.
The basic components of tires include natural and synthetic rubber, plasticizers, and
carbon black, steel wire, and fabricin the form of nylon, polyester, and metallic cords. For the
material flows methodology, material components of a tire are classified as rubber, steel, and
textiles.
Scrap tires are generated when tires are replaced on registered vehicles and when tires are
removed from vehicles that are taken out of service and deregistered. Scrap tires may also be
imported into the United States for end-of-life management. The materials flow methodology
assumes one tire is removed from service for every replacement tire sold and four tires are
removed from service for every deregistered vehicle. An average weight is assumed for
calculation of quantities for used tires material generated from the number of tires. Recovery of
used tires for recycling is estimated from the Rubber Manufacturers Association (RMA) data and
does not include recovery of used tires for fuel uses.
The primary sources of data for calculations associated with scrap tires are the RMA, the
U.S. Department of Commerce International Trade Commission (ITC) online database, the
National Automobile Dealers Association, and Modern Tire Dealer Magazine statistics.
Figure 15 illustrates generation, postconsumer recovery, and discards of used tires. Each
block of the flow diagram contains a reference number, which corresponds to the following
remarks.
1. Number of domestic vehicle replacement tires sold = car replacement tires + truck
replacement tires. Assumes a used tire is generated for every replacement tire
sold.
2. Number of deregistered vehicle tires = (car deregistrations x 4 tires/vehicle) +
(truck deregistrations x 4 tires/vehicle). Assumes four tires are removed from
service for every deregistered vehicle. To determine the number of deregistered
44
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
cars separately from deregistered trucks, the number of total deregistered vehicles
was multiplied by the percent operational cars represented of total operational cars
and trucks.
3. Imported used tires.
4. Total used car and truck tires = replacement car tires + replacement truck tires +
deregistered car tires + deregistered truck tires + imported used tires.
5. Used tire weight conversion factors for cars and trucks. Car conversion factor
(22.5 pounds per used tire, average); truck conversion factor (66 pounds per used
tire, average).
6. Total used tires = (car used tires (units) x unit weight of car tire (lbs per tire) +
truck used tires (units) x unit weight of truck tire (lbs per tire)) ^ 2,000 lbs per ton.
7. Material composition of used tires (percent of used tire weight) = Rubber (64.0
percent) + textiles (19.2 percent) + steel (16.8 percent). Material composition of
used tires equals the composition of new tires adjusted for rubber loss during use.
Rubber loss during use is assumed to be 20 percent.
8. Material composition of used tires (tons). Rubber = total used tires x percent of
used tire that is rubber (64.0 percent); Textiles = total used tires x percent of used
tire that is textiles (19.2 percent); Steel = total used tires x percent of used tire that
is steel (16.8 percent).
9. Net car tire retreads diverted in current year = current year car tire retreads - car
tire retreads two years previously. (Note: assumes average car tire retreads have a
useful life of two years and then the retread tires are ready for end-of-life
management.)
10. Net truck tire retreads diverted in current year = current year truck tire retreads -
truck tire retreads one year previously. (Note: assumes average truck tire retreads
have a useful life of one year and then the retread tires are ready for end-of-life
management.)
11. Net tire retreads = net car and truck retread tires (units) x unit weight of tire (lbs
per tire) ^ 2,000 lbs per ton. Net tire retreads reenter MSW generation.
12. Generation of used tires = used tires - tires diverted to retreading (tons) + used
tire retreads from previous years ready for end-of-life management (tons).
13. Recovery of used tires for recycling = generation of used tires x recovery rate of
used tires. (Note: tires recovered for fuel use not included in this recycling rate.)
14. Discards of used tires = generation of used tires - recovery of used tires for
recycling.
45
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Data Gaps
Deregistered vehicle data are only available as total vehicles and do not
distinguish between cars and trucks. To determine the number of used tires
generated from deregistered cars separately from deregistered trucks, the number
of total deregistered vehicles was multiplied by the percent operational cars
represented of total operational cars and trucks.
The number of scrap tires generated from deregistered vehicles (four per vehicle)
does not include spare tires. No available data have been identified to estimate the
occurrence or size (full size or space-saver) of spare tires removed when vehicles
are deregistered.
Imported used tires are assumed to be car tires. This assumption needs to be
reviewed.
Average weight of used truck tires is the average of light duty and commercial
truck tires (including medium and heavy duty trucks). No available data have been
identified to determine the ratio of used tires from light, medium, and heavy duty
trucks.
Composition of used tires is adjusted by applying a percent rubber loss due to
wear to new tire composition. This assumption needs to be reviewed.
46
-------
Municipal Solid Waste in the United States Facts and Figures A Methodology Document
Figure 15. Material Flow Methodology: Used Tires
Figure 15. Material Flow Methodology: Used Tires (Continued)
47
------- |