CRA UNITED STATES ENVIRONMENTAL PROTECTION AGENCY CrM NATIONAL EXPOSURE RESEARCH LABORATORY Environmental Protection EXPOSURE METHODS AND MEASUREMENT DIVISION (MD-D205-03) Agency Research Triangle Park, NC 27711 Office of Research and Development LIST OF DESIGNATED REFERENCE AND EQUIVALENT METHODS Issue Date: December 17, 2016 (www.epa.gov/ttn/amtic/criteria.html) These methods for measuring ambient concentrations of specified air pollutants have been designated as "reference methods" or "equivalent methods" in accordance with Title 40, Part 53 of the Code of Federal Regulations (40 CFR Part 53). Subject to any limitations (e.g., operating range or temperature range) specified in the applicable designation, each method is acceptable for use in state or local air quality surveillance systems under 40 CFR Part 58 unless the applicable designation is subsequently canceled. Automated methods for pollutants other than PMio are acceptable for use only at shelter temperatures between 20°C and 30°C and line voltages between 105 and 125 volts unless wider limits are specified in the method description. Prospective users of the methods listed should note (1) that each method must be used in strict accordance with its associated operation or instruction manual and with applicable quality assurance procedures, and (2) that modification of a method by its vendor or user may cause the pertinent designation to be inapplicable to the method as modified. (See Section 2.8 of Appendix C, 40 CFR Part 58 for approval of modifications to any of these methods by users.) Further information concerning particular designations may be found in the Federal Register notice cited for each method or by writing to the National Exposure Research Laboratory, Exposure Methods and Measurement Division (MD-D205-03), U.S. Environmental Protection Agency, Research Triangle Park, North Carolina 27711. Technical information concerning the methods should be obtained by contacting the source listed for each method. Source addresses are listed at the end of the listing of methods, except for the addresses for lead method sources, which are given with the method. New analyzers or PMio samplers sold as reference or equivalent methods must carry a label or sticker identifying them as designated methods. For analyzers or PMio samplers sold prior to the designation of a method with the same or similar model number, the model number does not necessarily identify an analyzer or sampler as a designated method. Consult the manufacturer or seller to determine if a previously sold analyzer or sampler can be considered a designated method or if it can be upgraded to designation status. Analyzer users who experience operational or other difficulties with a designated analyzer or sampler and are unable to resolve the problem directly with the instrument manufacturer may contact EPA (preferably in writing) at the above address for assistance. This list will be revised as necessary to reflect any new designations or any cancellation of a designation currently in effect. The most current revision of the list will be available for inspection at EPA's Regional Offices, and copies may be obtained at the Internet site identified above or by writing to the National Exposure Research Laboratory at the address specified above. ------- Most Recent Designations Sutron Model 6020 Sulfur Dioxide Fluorescent Analyzer July 2016 Teledyne API Model T640 PM mass monitor with 640X option (PM10, PM2 sand PM10-25) July 2016 Teledyne API Model T640 PM mass monitor (PM2 5) July 2016 Teledyne API Model T200P Chemiluminescence Nitrogen Oxides Analyzer October 2016 ------- TSP List of Designated Reference and Equivalent Methods. December 17.2016 Page 3 Particulate Matter - TSP Reference Method for TSP Manual Reference Method: 40 CFR Part 50, Appendix B Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method) Federal Register: Vol. 47, page 54912,12/06/82 and Vol 48, page 17355, 04/22/1983 ------- PMio List of Designated Reference and Equivalent Methods. December 17.2016 Page 4 Particulate Matter - PM10 Andersen Model RAAS10-100 PMto Single Channel PMio Sampler Manual Reference Method: RFPS-0699-130 "Andersen Instruments, Incorporated Model RAAS10-100 Single Channel Reference Method PMio Sampler," with RAAS-10 PMio inlet or the louvered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, configured as a PMio reference method, and operated for a continuous 24-hour sample period at a flow rate of 16.67 Lpm, and in accordance with the Model RAAS105-100 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix J. Federal Register: Vol. 64, page 33481, 06/23/1999 Andersen Model RAAS10-200 PMio Single Channel PMio Audit Sampler Manual Reference Method: RFPS-0699-131 "Andersen Instruments, Incorporated Model RAAS10-200 Single Channel Reference Method PMio Audit Sampler," with RAAS-10 PMio inlet or the louvered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, configured as a PMio reference method, and operated for a continuous 24-hour sample period at a flow rate of 16.67 Lpm, and in accordance with the Model RAAS105-200 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix J. Federal Register: Vol. 64, page 33481, 06/23/1999 Andersen Model RAAS10-300 PMioMulti Channel PMio Sampler Manual Reference Method: RFPS-0699-132 "Andersen Instruments, Incorporated Model RAAS10-300 Multi Channel Sequential Reference Method PMio Sampler," with RAAS-10 PMio inlet or the lowered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, configured as a PMio reference method, and operated for a continuous 24-hour sample period at a flow rate of 16.67 Lpm, and in accordance with the Model RAAS105-300 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix J. Federal Register: Vol. 64, page 33481, 06/23/1999 BGI Incorporated Model PQ100 Air Sampler Manual Reference Method: RFPS-1298-124 "BGI Incorporated or Mesa Laboratories Incorporated Model PQ100 Air Sampler," with BGI 16.7 Inlet Kit or the lowered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, configured as a PMio reference method, for a continuous 24- hour sample period at a flow rate of 16.7 Lpm, with original firmware Version 5.X and lower or new firmware version 6.0 and higher, operated in accordance with the original Model PQ100 Instruction Manual or manual revision Version 7.0, as appropriate, and with the requirements specified in 40 CFR Part 50, Appendix J, using either the original or the newer PQ200- type filter cassettes, and with or without the optional Solar Panel Power Supply. Federal Register: Vol. 63, page 69625,12/17/1998 Latest modification: 01/2009; 6/2015 BGI Incorporated Model PQ200 Air Sampler Manual Reference Method: RFPS-1298-125 "BGI Incorporated or Mesa Laboratories Incorporated Model PQ200 Air Sampler," with "flat plate" PMio inlet or the lowered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, configured as a PMio reference method, and operated for a continuous 24-hour sample period in accordance with the Model PQ200 Instruction Manual and with the requirements specified in 40 CFR Part 50, Appendix J, and with or without the optional Solar Panel Power Supply. Federal Register: Vol. 63, page 69625,12/17/1998 Latest modification: 6/2015 DKK-TOA Models FPM-222/222C, FPM223/223C, and DUB-222(S)/223(S) PMio Monitor Automated Equivalent Method: EQPM-0905-156 "DKK-TOA Models FPM-222, FPM-222C, FPM-223, FPM-223C, DUB-222(S), and DUB-223(S) Particulate Monitor," for monitoring PMio in Ambient Air (beta attenuation monitor), configured for PMio, with Firmware Version DUB4-658355, Corrected Slope Factor (FACT SLOPE) set to 1.232, Corrected Zero Value (FACT ZERO) set to 1.8, and with or without any of the following options: Auto Check and Serial Recorder. Federal Register: Vol. 70, page 56684, 09/28/2005 ------- PMio List of Designated Reference and Equivalent Methods. December 17.2016 Page 5 Ecotech Model 3000 PMio High Volume Air Sampler Manual Reference Method: RFPS-0706-162 "Ecotech Pty. Ltd. Model 3000 PMio High Volume Air Sampler," configured with the Ecotech PMio Size-Selective Inlet (SSI)(P-ECO-HVS3000-02), with the flow rate set to 1.13 m3/min (67.8 m3/hour). Federal Register: Vol. 71, page 42089, 07/25/2006 Environnement S.A. Model MP101M PMio Monitor Automated Equivalent Method: EQPM-0404-151 "Environnement S. A. Model MP101M PMio Beta Gauge Monitor," configured with the louvered PMio inlet specified in 40 CFR 50 Appendix L or its flat-topped predecessor version and one of the three optional temperature-regulated sampling tubes (RST), and operated with a full scale measurement range of 0 - 0.500 mg/m3 (0 - 500 :g/m3), with the sample flow rate set to 1.00 m3/h and flow regulation set to yes, the "norms selection" set to m3 (actual volume), the "cycle" set to 24 hours, the "period" set to none, and the "counting time" set to 200 seconds.2 Federal Register: Vol. 69, page 18569, 4/8/2004 Graseby Andersen/GMW Model 1200 High-Volume Air Sampler Manual Reference Method: RFPS-1287-063 "Sierra-Andersen or General Metal Works Model 1200 PMio High-Volume Air Sampler System," consisting of a Sierra- Andersen or General Metal Works Model 1200 PMio Size-Selective Inlet and any of the high-volume air samplers identified as SAUV-10H, SAUV-11H, GMW-IP-10, GMW-IP-10-70, GMW-IP-10-801, or GMW-IP-10-8000, which include the following components: Anodized aluminum high-volume shelter with either acrylonitrile butadiene styrene plastic filter holder and motor/blower housing or stainless steel filter holder and phenolic plastic motor/blower housing; 0.6 hp motor/blower; pressure transducer flow recorder; either an electronic mass flow controller or a volumetric flow controller; either a digital timer/programmer, seven-day mechanical timer, six-day timer/programmer, or solid-state timer/programmer; elapsed time indicator; and filter cartridge. Federal Register: Vol. 52, page 45684,12/01/1987 and Vol 53, page 1062, 01/15/1988 Graseby Andersen/GMW Model 321-B High-Volume Air Sampler Manual Reference Method: RFPS-1287-064 "Sierra-Andersen or General Metal Works Model 321-B PMio High-Volume Air Sampler System," consisting of a Sierra- Andersen or General Metal Works Model 321-B PMio Size-Selective Inlet and any of the high-volume air samplers identified as SAUV-10H, SAUV-11H, GMW-IP-10, GMW-IP-10-70, GMW-IP-10-801, or GMW-IP-10-8000, which include the following components: Anodized aluminum high-volume shelter with either acrylonitrile butadiene styrene plastic filter holder and motor/blower housing or stainless steel filter holder and phenolic plastic motor/blower housing; 0.6 hp motor/blower; pressure transducer flow recorder; either an electronic mass flow controller or a volumetric flow controller; either a digital timer/programmer, seven-day mechanical timer, six-day timer/programmer, or solid-state timer/programmer; elapsed time indicator; and filter cartridge. Federal Register: Vol. 52, page 45684,12/01/1987 and Vol 53, page 1062, 01/15/1988 Graseby Andersen/GMW Model 321-C High-Volume Air Sampler Manual Reference Method: RFPS-1287-065 "Sierra-Andersen or General Metal Works Model 321-C PMio High-Volume Air Sampler System," consisting of a Sierra- Andersen General Metal Works Model 321-C PMio or Size-Selective Inlet and any of the high-volume air samplers identified as SAUV-10H, SAUV-11H, GMW-IP-10, GMW-IP-10-70, GMW-IP-10-801, or GMW-IP-10-8000, which include the following components: Anodized aluminum high-volume shelter with either acrylonitrile butadiene styrene plastic filter holder and motor/blower housing or stainless steel filter holder and phenolic plastic motor/blower housing; 0.6 hp motor/blower; pressure transducer flow recorder; either an electronic mass flow controller or a volumetric flow controller; either a digital timer/programmer, seven-day mechanical timer, six-day timer/programmer, or solid-state timer/programmer; elapsed time indicator; and filter cartridge. Federal Register: Vol. 52, page 45684,12/01/1987 and Vol 53, page 1062, 01/15/1988 ------- PMio List of Designated Reference and Equivalent Methods. December 17.2016 Page 6 Graseby Andersen/GMWModels SA241 and SA241MDichotomous Sampler Manual Reference Method: RFPS-0789-073 "Sierra-Andersen Models SA241 and SA241M or General Metal Works Models G241 and G241M PMio Dichotomous Samplers," consisting of the following components: Sampling Module with SA246b or G246b 10 nm inlet or the louvered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, 2.5 nm virtual impactor assembly, 37 mm coarse and fine particulate filter holders, and tripod mount; Control Module with diaphragm vacuum pump, pneumatic constant flow controller, total and coarse flow rotameters and vacuum gauges, pressure switch (optional), 24-hour flow/event recorder, digital timer/programmer or 7-day skip timer, and elapsed time indicator. Federal Register: Vol. 54, page 31247, 07/27/1989 Graseby Andersen/GMW Model FH621-N Beta Monitor Automated Equivalent Method: EQPM-0990-076 "Andersen Instruments Model FH62I-N PMio Beta Attenuation Monitor," consisting of the following components: FH101 Vacuum Pump Assembly; FH102 Accessory Kit; FH107 Roof Flange Kit; FH125 Zero and Span PMio Mass Foil Calibration Kit; FH62I Beta Attenuation 19-inch Control Module; SA246b PMio Inlet (16.7 Lpm) or the louvered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19; operated for 24-hour average measurements, with an observing time of 60 minutes, the calibration factor set to 2400, a glass fiber filter tape, an automatic filter advance after each 24-hour sample period, and with or without either of the following options: FH0P1 Indoor Cabinet; FH0P2 Outdoor Shelter Assembly. Federal Register: Vol. 55, page 38387, 09/18/1990 Met One or Sibata Models BAM/GBAM1020, BAM/GBAM1020-1, Horiba APDA-3 71, or Ecotech Spirant BAM1000 Automated Equivalent Method: EQPM-0798-122 "Met One Instruments or Sibata Scientific Technology Models BAM 1020, GBAM 1020, BAM 1020-1, GBAM 1020-1, Horiba APDA-371 PMio Beta Attenuation Monitor, or Ecotech Spirant BAM1000" including the BX-802 EPA PMio inlet (or alternative lowered PMio inlet meeting 40 CFR 50 Appendix L specifications), operated for 24-hour average measurements, with a filter change frequency of one hour, with glass fiber filter tape, and with or without any of the following options: BX- 823, tube extension; BX-825, heater kit; BX-826, 230 VAC heater kit; BX-827 "Smart Heater" set for maintaining moisture between 35% and 45% and no AT control; BX-828, roof tripod; BX-902, exterior enclosure; BX-903, exterior enclosure with temperature control; BX-961, mass flow controller; BX-967, internal calibration device, BX-970 touch-screen display with USB interface. For software (firmware) versions V3.0 or higher, a user-selectable measurement time (COUNT TIME) of 4, 6, 8 or 10 minutes selected, along with appropriate sample time (BAM SAMPLE) setting of 50,46,42 or 38 minutes, respectively, to maintain a 60-minute measurement cycle. For software (firmware) versions V3.5 or higher, user-selectable option to sample under actual conditions (Flow Type: ACTUAL) and report under standard conditions (Reporting: STD), which requires the use of P/N BX-592 external temperature sensor or P/N BX-596 external temperature/barometric pressure sensor. The user may also sample under standard conditions (Flow Type: STD) and report under standard conditions (Reporting: STD) with any software/firmware 2.0 or higher. Instrument must be operated in accordance with the appropriate instrument manual. Federal Register: Vol. 63, page 41253, 08/03/1998 Latest modifications: 06/2009; 07/2010; 8/2010; 8/2012 Met One Instruments, Inc. E-BAMPLUS Beta Attenuation Mass Monitor- PMio FEM Configuration Automated Equivalent Method: EQPM-1215-226 "Met One Instruments, Inc. E-BAM PLUS Beta Attenuation Mass Monitor - PMio FEM Configuration," configured for 24 1- hour average measurements of PMio by beta attenuation, using a glass fiber filter tape roll (460130 or 460180), a sample flow rate of 16.67 liters/min, with the standard (BX-802) EPA PMio inlet (meeting 40 CFR 50 Appendix L specifications) and equipped with 9250 ambient temperature sensor. Instrument must be operated in accordance with the E-BAM PLU S Particulate Monitor operation manual, revision 1 or later. This designation applies to PMio measurements only. Federal Register: Vol. 81, page 4294, 01/26/2016 Met One Instruments, Inc. E-FRM- PMio Manual Reference Method: RFPS-0216-231 "Met One Instruments, Inc. E-FRM," configured for filter sampling of ambient particulate matter using the US EPA PMio inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, with a flow rate of 16.67 L/min, using 47 mm PTFE membrane filter media, and operating with firmware version R2.0.1 and later, and operated in accordance with the Met One E-FRM PM10 operating manual. This designation applies to PMio measurements only. Federal Register: Vol. 81, page 25397, 04/28/2016 ------- PMio List of Designated Reference and Equivalent Methods. December 17.2016 Page 7 Opsis Model SM200 PMio Monitor Automated Equivalent Method: EQPM-0810-193 "Opsis Model SM200 Monitor," beta gauge semi-continuous ambient particulate monitor operated for 24 hours at a flow rate of 16.67 Lpm between 5° and 40°C using 47 mm PTFE membrane filter media, in the mass measurement range of 0 to 60 mg, configured with a BGI Model SSI25 PMio inlet meeting criteria specified in 40 CFR 50 Appendix L, with a roof mounting kit, and with or without an inlet tube heater (as recommended based on site RH conditions), according to the SM200 User's Guide. Federal Register: Vol. 75, page 51039, 08/18/2010 Oregon DEQ Medium Volume PMio Sampler Manual Reference Method: RFPS-0389-071 "Oregon DEQ Medium Volume PMio Sampler." NOTE: This method is no longer commercially available. Federal Register: Vol. 54, page 12273, 03/24/1989 Teledyne Model 602 BetaPLUS Particle Measurement System or SWAM 5a Dual Channel Monitor Automated Equivalent Method: EQPM-0912-205 "Teledyne Model 602 Bcta'"/ , ;s Particle Measurement System" or "SWAM 5a Dual Channel Monitor" configured for 1-hour measurements of PMio by beta attenuation on a single sampling line (Line A or B, but not both together), with the standard, louvered US EPA PMio size selective inlet specified in 40 CFR 50 Appendix L, using 47 mm glass fiber filters, at a sample flow set to 16.67 liters/min and software version 05-02.07.63 or later. Operated in accordance with the Teledyne Model 602 Bcta'"/ , :s Particle Measurement System Operation Manual. Federal Register: Vol. 77, page 60985,10/5/2012 Teledyne Advanced Pollution Instrumentation Model T640 PM mass monitor with 640X option Automatic Equivalent Method: EQPM-0516-239 "Teledyne Advanced Pollution Instrumentation Model T640 PM mass monitor with 640X option," continuous ambient particulate monitor operated at a volumetric flow rate of 16.67 Lpm, equipped with the louvered PMio inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, TAPI aerosol sample conditioner (P/N: 081040000), configured for operation with firmware version 1.0.2.126 or later, in accordance with the Teledyne Model T640 Operations Manual. This designation applies to PMio measurements only. Federal Register: Vol. 81, page 45285, 07/13/2016 Thermo Andersen Series FH 62 C14 Continuous PM in Monitor Thermo Scientific Model 5014i Beta (5014i Beta), Continuous Ambient Particulate Monitor Automated Equivalent Method: EQPM-1102-150 "Thermo Andersen Series FH 62 C14 Continuous PMio Ambient Particulate Monitor and Thermo Scientific Model 5014i Beta (5014i Beta), Continuous Ambient Particulate Monitor," operated for 24-hour average measurements, with the specified 10- micron EPA PMio inlet (or alternative lowered PMio inlet meeting 40 CFR 50 Appendix L specifications), inlet connector, sample tube with heater, roof flange kit, mass foil kit, pump kit, sample filter tape; with operational settings of 1000 L/h (16.67 L/min) sample flow rate, daily filter change, auto filter change at volumetric flow <950 L/h, auto filter change at mass >1500 micrograms, and factory default calculation mode settings operated with software version 1.07. Operated, calibrated and serviced according to the appropriate Operator Manual. Federal Register: Vol. 67, page 76174,12/11/2002 Latest modifications: 07/2009; 12/2012 Thermo Scientific or Rupprecht & Patashnick Partisol" Model 2000 Air Sampler Manual Reference Method: RFPS-0694-098 "Thermo Scientific Partisol® 2000 Air Sampler" or "Rupprecht & Patashnick Partisol® Model 2000 Air Sampler," consisting of a Hub Unit and 0, 1, 2, or 3 Satellite Units, with each sampling station used for PMio measurements equipped with a Rupprecht & Patashnick PMio inlet and operated for continuous 24-hour sampling period using the Basic, Manual, Time, Analog Input, or Serial Input programming modes, and with or without any of the following options: PM2 5-style filter cassette holder; lowered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19 in lieu of standard inlet; 57-002320 Stand for Hub or Satellite; 59-002542 Advanced EPROM; 10-001403 Large Pump (1/4 hp); 120 VAC. Hardware for Indoor Installation consists of: 51-002638-xxxx Temperature Sensor (Extended Length); 55-001289 Roof Flange (1 1/4"); 57-000604 Support Tripod for Inlet; 57-002526-0001 Sample Tube Extension (1 m); 57-002526-0002 Sample Tube Extension (2 m). Hardware for Outdoor Installation in Extreme Cold Environments consists of: 10-002645 Insulating Jacket for Hub Unit. Federal Register: Vol. 59, page 35338, 07/11/1994 ------- PMio List of Designated Reference and Equivalent Methods. December 17.2016 Page 8 Thermo Scientific Partisof 2000-D Dichotomous Air Sampler or Thermo Fisher Scientific Partisof 2000i-D Dichotomous Air Sampler Manual Equivalent Method: EQPS-0311-197 "Thermo Scientific Partisol® 2000-D Dichotomous Air Sampled' or "Thermo Fisher Scientific Partisol® 2000/-D Dichotomous Air Sampler," configured for dual-filter, single-event sampling of fine (PM25) and coarse (PMms) particles, operated with a U.S. EPA PM10 inlet and using a virtual impactor to separate fine and coarse PM into two samples for collection on two separate filter membranes, for a 24-hour sampling period and in accordance with the Partisol® 2000-D or Partisol® 2000/-D instruction manual, as appropriate. Partisol® 2000/-D operated with firmware version 2.0 or greater. Federal Register: Vol 76, page 15974,03/22/2011 Latest modification: 06/2011 Thermo Scientific Partisol® 2000-FRM PM10 Air Sampler or Thermo Fisher Scientific Partisol® 2000i PM10 Air Sampler or Rupprecht andPatashnick Partisol-FRM 2000 PMioAir Sampler Manual Reference Method: RFPS-1298-126 "Thermo Scientific Partisol® 2000-FRM PM10 Air Sampler" or "Thermo Fisher Scientific Partisol® 2000/ PM10 Air Sampler" or "Rupprecht and Patashnick Partisol®-FRM 2000 PM10 Air Sampler," with PM10 inlet or louvered inlet specified in 40 CFR 50, Appendix L, Figs. L-2 through L-19, configured as a PM10 reference method with a U.S. EPA PM10 inlet with straight downtube adapter and operated for continuous 24-hour sample periods in accordance with the Partisol® 2000-FRM or Partisol® 2000/ instruction manual, as appropriate, and with the requirements specified in 40 CFR Part 50, Appendix J. Model 2000/ operated with firmware version 2.0 or greater. Federal Register: Vol. 63, page 69625,12/17/1998 Latest modification: 06/2011 Thermo Scientific Partisol-Plus 2025 PM10 Sequential Air Sampler or Thermo Fisher Scientific Partisol 2025i PM10 Sequential Air Sampler or Rupprecht and Patashnick Partisol91-Plus 2025 PM10 Sequential Air Sampler Manual Reference Method: RFPS-1298-127 "Thermo Scientific Partisol®-Plus 2025 Sequential Air Samplef' or "Thermo Fisher Scientific Partisol® 2025/ Sequential Air Samplef' or "Rupprecht and Patashnick Partisol®-Plus 2025 PM10 Sequential Air Sampler," with PM10 inlet or louvered inlet specified in 40 CFR 50, Appendix L, Figs. L-2 through L-19, configured as a PM10 reference method and operated for continuous 24-hour sample periods. Partisol®-Plus 2025 to be operated with any software version 1.003 through 1.5 and the Partisol® 2025/ with firmware version 2.0 or greater, with the modified filter shuttle mechanism, in accordance with the Partisol®-Plus 2025 or Partisol® 2025/ instruction manual, as appropriate, and with the requirements specified in 40 CFR Part 50, Appendix J. Federal Register: Vol. 63, page 69625,12/17/1998 Last modified: 06/2011 Thermo Scientific Dichotomous Partisol -Plus 2025-D Sequential Air Sampler or Thermo Fisher Scientific Dichotomous Partisol8 2025i-D Sequential Air Sampler Manual Equivalent Method: EQPS-0311-198 "Thermo Scientific Dichotomous Partisol®-Plus 2025-D Sequential Air Sampler" or "Thermo Fisher Scientific Dichotomous Partisol® 2025/-D Sequential Air Sampler," configured for dual-filter sampling of fine (PM2 5) and coarse (PM10-25) particles, with a U.S. EPA PM10 inlet and using a virtual impactor to separate the fine and coarse PM into two samples for collection on two separate filter membranes, and operated with the modified filter shuttle mechanism implemented May 31, 2008, and firmware version 1.500 or greater for the Partisol®-Plus 2025-D and version 2.0 or greater for the Partisol® 2025/-D, for continuous 24-hour sample periods , in accordance with the Partisol®-Plus 2025-D or Partisol® 2025/-D instruction manual, as appropriate. Federal Register: Vol. 76, page 15975, 03/22/2011 Latest modification: 06/2011 Thermo Scientific TEOM® 1400AB/TEOM® 1405 Ambient Particulate Monitor or Rupprecht & Patashnick TEOM® Series 1400/1400a PMm Monitors Automated Equivalent Method: EQPM-1090-079 "Thermo Scientific TEOM® 1400AB [PM10] Ambient Particulate Monitor" or "Rupprecht & Patashnick TEOM® Series 1400 and Series 1400a PM-10 Monitors," (including serial number prefixes 1400, 140A, 140AA, 140AB, 140AT, and 140UP, 1405A), consisting of the following components: TEOM® Sensor Unit; TEOM® Control Unit; Flow Splitter (3 Lpm sample flow); Teflon-Coated Glass Fiber Filter Cartridges; Rupprecht & Patashnick PM-10 Inlet (part number 57-00596), Sierra- Andersen Model 246b PM-10 Inlet (16.7 Lpm) or lowered inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19; operated for 24-hour average measurements, with the total mass averaging time set at 300 seconds, the mass rate/mass concentration averaging time set at 300 seconds, the gate time set at 2 seconds, and with or without any of the following options: ------- PMio List of Designated Reference and Equivalent Methods. December 17.2016 Page 9 Tripod; Outdoor Enclosure; Automatic Cartridge Collection Unit (Series 1400a only); Flow Splitter Adapter (for 1 or 2 Lpm sample flow). Thermo Scientific TEOM® 1405 Ambient Particulate Monitor with combined sensor and control units and redesigned mass transducer and user interface, operated in accordance with the Thermo Scientific TEOM® 1405 instrument manual. Federal Register: Vol. 55, page 43406,10/29/1990 Latest modification: 12/2008 ------- PMio List of Designated Reference and Equivalent Methods. December 17.2016 Page 10 Thermo Scientific TEOM® 1405-DFDichotomous Ambient Particulate Monitor with FDMS® Automated Equivalent Method: EQPM-1013-208 "Thermo Scientific TEOM® 1405-DF Dichotomous Ambient Particulate Monitor with FDMS®," configured for dual filter sampling of fine (PM2 5) and coarse particles using the US EPA PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19 and a virtual impactor, with a total flow rate of 16.67 L/min, fine sample flow of 3 L/min, and coarse sample flow rate of 1.67 L/min, and operating with firmware version 1.70 and later, operated with or without external enclosures, and operated in accordance with the Thermo Scientific TEOM® 1405-DF Dichotomous Ambient Particulate Monitor Instruction Manual. This designation applies to PM10 measurements only. Federal Register: Vol. 78, page 67360,11/12/2013 Tisch Environmental Model TE-6070 PM10 High-Volume Air Sampler or New Star Environmental Model NS-6070 PM10 High-Volume Air Sampler Manual Reference Method: RFPS-0202-141 "Tisch Environmental Model TE-6070 or New Star Environmental Model NS-6070 PM10 High-Volume Air Sampler," consisting of a TE-6001 PM10 size-selective inlet, 8" x 10" filter holder, aluminum outdoor shelter, mass flow controller or volumetric flow controller with brush or brushless motor, 7-day mechanical off/on-elapsed timer or 11-day digital off/on- elapsed timer, and any of the high volume sampler variants identified as TE-6070-BL or NS-6070-BL, TE-6070D or NS- 6070D, TE-6070D-BL orNS-6070-BL, TE-6070V or NS-6070V, TE-6070V-BL or NS-6070V-BL, TE-6070-DVorNS-6070- DV, or TE-6070DV-BL or NS-6070DV-BL, with or without the optional stainless steel filter media holder/filter cartridge or continuous flow/pressure recorder. Federal Register: Vol. 67, page 15566, 04/02/2002 Tisch Environmental Model TE- Wilbur 10 Particulate Sampler - PM10 Manual Reference Method: RFPS-0714-216 "Tisch Environmental Model TE-WilburlO PM10 Low-Volume Air Particulate Sampler," consisting of a TE-PM10-D PM10 size-selective inlet, specified in 40 CFR 50 Appendix L Figs. L-2 thru L-19, configured as a PM10 reference method, operated for continuous 24-hour sample period at a flow rate of 16.67 L/min, using 47 mm PTFE membrane filter media, operated with or without the optional TE-W-600 Solar Panel Power Supply kit, operating with firmware version 1.70 or later, and operated in accordance with the Tisch Environmental Model TE-WilburlO PM10 Low-Volume Air Particulate Sampler instruction manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix J. Federal Register: Vol. 79, page 49307, 08/20/2014 Latest modification: 6/2015 Wedding & Associates' or Thermo Environmental Instruments Inc. Model 600 PM10 High-Volume Sampler Manual Reference Method: RFPS-1087-062 "Wedding & Associates' or Thermo Environmental Instruments, Inc. Model 600 PM10 Critical Flow High-Volume Sampler," consisting of the following W&A/TEII components: PM10 Inlet; Critical Flow Device; Anodized Aluminum Shelter; Blower Motor Assembly for 115, 220 or 240 VAC and 50/60 Hz; Mechanical Timer; Elapsed Time Indicator; and Filter Cartridge/Cassette, and with or without the following options: Digital Timer, 6 or 7 Day Timer, and 1 or 7 Day Pressure Recorder. Federal Register: Vol. 52, page 37366, 10/06/1987 Wedding & Associates' or Thermo Environmental Instruments Inc. Model 650 PMioBeta Gauge Automated Equivalent Method: EQPM-0391-081 "Wedding & Associates' or Thermo Environmental Instruments, Inc. Model 650 PM10 Beta Gauge Automated Particle Sampler," consisting of the following W&A/TEII components: Particle Sampling Module, PM10 Inlet (18.9 Lpm), Inlet Tube and Support Ring, Vacuum Pump (115, 220 or 240 VAC and 50/60 Hz); and operated for 24-hour average measurements with glass fiber filter tape. Federal Register: Vol. 56, page 9216, 03/05/1991 ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 11 Particulate Matter - PM2.5 Andersen Model RAAS2.5-200 PM2.5 Ambient Audit Air Sampler Manual Reference Method: RFPS-0299-128 "Andersen Instalments, Incorporated Model RAAS2.5-200 PM2 5 Audit Sampler," configured as a PM2 5 reference method and operated with software (firmware) version 4B, 5.0.1 - 6.09, 6.0A, or 6.0B, for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, and in accordance with the Model RAAS2.5-200 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 64, page 12167, 03/11/1999 BGIInc. Models PQ200 or PQ200A PM2.5 Ambient Fine Particle Sampler Manual Reference Method: RFPS-0498-116 "BGI Incorporated or Mesa Laboratories Incorporated Models PQ200 and PQ200A PM25 Ambient Fine Particle Sampler," operated with firmware version 3.88, 3.89R, 3.91, 3.91R and 5.62 for a continuous 24-hour sample period, in accordance with the Model PQ200/PQ200A Instruction Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L, and with or without the optional Solar Power Supply or the optional dual-filter cassette (P/N F-21/6) and associated lower impactor housing (P/N B2027), where the upper filter is used for PM2 5. The Model PQ200A is described as a portable audit sampler and includes a set of three carrying cases. Federal Register: Vol. 63, page 18911, 04/16/1998 Latest modification: 6/2015; 06/2016; 12/2016 BGI Inc. Models PQ200-VSCC™ or PQ200A- VSCC™ PM25 Sampler Manual Reference Method: RFPS-0498-116 or Manual Equivalent Method: EQPM-0202-142 "BGI Incorporated or Mesa Laboratories Incorporated Models PQ200-VSCC™ or PQ200A-VSCC™ PM25 Ambient Fine Particle Sampler," configured with a BGI Very Sharp Cut Cyclone (VSCC™) particle size separator and operated with firmware version 3.88, 3.89R, 3.91, 3.91R and 5.62 for a continuous 24-hour sample period, in accordance with the Model PQ200/PQ200A Instruction Manual and VSCC™ supplemental manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L, and with or without the optional Solar Power Supply or the optional dual-filter cassette (P/N F-21/6) and associated lower impactor housing (P/N B2027), where the upper filter is used for PM2 5. The Model PQ200A VSCC™ is described as a portable audit sampler and includes a set of three carrying cases. Federal Register: Vol. 67, page 15567, 04/02/2002 Latest modification: 6/2015; 06/2016; 12/2016 Environnement S.A. Model MP101M PM2.5 Monitor Automated Equivalent Method: EQPM-1013-211 "Environnement S.A. Model MP101M PM2.5 Beta Attenuation Monitor" using a glass fiber filter tape roll, operated at a sample flow rate of 16.67 liters/min for 24-hour average measurements of PM2 5, configured with the standard EPA PM10 inlet (meeting 40 CFR 50 Appendix L specifications) associated with a BGI Very Sharp Cut Cyclone (VSCC™) particle size separator and using a temperature regulated sampling tube with ambient meteorological sensor. With or without optional ESTEL analog inputs/outputs, serial link: 1 RS-232/422; USB port; Ethernet port (TCP/IP). Instrument must be operated in accordance with the Ambient Air Continuous Particulate Monitor Model MP 101M operation manual. This designation applies to PM2 5 measurements only. Federal Register: Vol. 78, page 67360,11/12/2013 Graseby Andersen Model RAAS2.5-100 PM2.5 Ambient Air Sampler Manual Reference Method: RFPS-0598-119 "Graseby Andersen Model RAAS2.5-100 PM2 5 Ambient Air Sampler," operated with software version 4B, 5.0.1 - 6.09, 6.OA, or 6.0B, configured for "Single 2.5" operation, for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, and in accordance with the Model RAAS2.5-100 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 63, page 31991, 06/11/1998 ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 12 Graseby Andersen Model RAAS2.5-300 PM2.5 Sequential Ambient Air Sampler Manual Reference Method: RFPS-0598-120 "Graseby Andersen Model RAAS2.5-300 PM2 5 Sequential Ambient Air Sampler," operated with software version 4B, 5.0.1 - 6.09, 6.0A, or 6.0B, configured for "Multi 2.5" operation, for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, and in accordance with the Model RAAS2.5-300 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 63, page 31991, 06/11/1998 Grimm Model EDM 180 PM2. s Monitor Automated Equivalent Method: EQPM-0311-195 "Grimm Technologies, Inc. Model EDM 180 PM2 5 or Tisch Environmental TE-EDM 180 PM2 5 Monitor," light scattering continuous ambient particulate monitor operated for 24 hours at a volumetric flow rate of 1.2 L/min, configured with a Nafion®- type air sample dryer, complete for operation with firmware version 7.80, in accordance with the Grimm Technologies, Inc. Model EDM 180 Operation and Instruction Manual. The optional graphic presentation can be made with the software model 1.177 version 3.30. Federal Register: Vol. 76, page 15974, 03/22/2011 Latest Modification: 01/2012; 3/2014; 12/2016 Met One Instruments, Inc. BAM-1020 Monitor - PMzs FEM Configuration, Horiba APDA-371- PMzs Configuration, or Ecotech Spirant BAM1100 Automated Equivalent Method: EQPM-0308-170 "Met One Instruments, Inc. BAM-1020 Beta Attenuation Mass Monitor - PM25 FEM Configuration, Horiba Instruments APDA-371 Beta Attenuation Mass Monitor - PM2 5 FEM Configuration, or Ecotech Spirant BAM1100", configured with the standard BX-802 EPA PM10 inlet (or alternative louvered PM10 inlet meeting 40 CFR 50 Appendix L specifications) and with a BGI VSCC™ Very Sharp Cut Cyclone or Tisch TE-PM2.5C particle size separator, operated for 24 1-hour average measurements with firmware revision 3.2.4 or later, with or without an inlet tube extension (BX-823), with or without external enclosures BX-902 or BX-903 and equipped with BX-596 ambient temperature and barometric pressure combination sensor, internal BX-961 automatic flow controller operated in Actual (volumetric) flow control mode, the standard BX-802 EPA PM10 inlet head and a BGI Veiy Sharp Cut Cyclone (VSCC™ -A) or Tisch TE-PM2.5C cyclone, BX-827 (110V) or BX-830 (230V) Smart Inlet Heater, with the heater RH set to 35% and the temperature control set to "off", the 8470-1 revision D or later tape control transport assembly with close geometry beta source configuration, used with standard glass fiber filter tape, COUNT TIME parameter set for 8 minutes, the SAMPLE TIME parameter set for 42 minutes, BX-302 zero filter calibration kit required and with or without BX-970 touch-screen display with USB interface. Instrument must be operated in accordance with the BAM 1020 Particulate Monitor operation manual, revision F or later, the Horiba APDA-371 Monitor operation manual or the Ecotech Spirant BAM Manual (rev.A or later), as appropriate, and the VSCC™ or Tisch TE-PM2.5C supplemental manual. Alternatively, BX-851 (110V) or BX-852 (230V) Dew Point Heating System (DPHS) with BX-597 T/BP/RH sensor may be substituted for the BX-827 (110V) or BX-830 (230V) Smart Inlet Heater with BX-596 T/BP sensor. DPHS must be operated in accordance with BAM 1020 Particulate Monitor with DPHS operational manual. DPHS requires firmware V3.10.0 or greater for the standard BAM-1020 and firmware V4.4.0 with the Touch Screen Display Option (BX-970). Federal Register: Vol. 73, page 13224, 03/12/2008 Latest modifications: 7/2010; 8/2010; 8/2012; 3/2015; 9/2015 Met One Instruments, Inc. BAM-1020 Beta Attenuation Mass Monitor- PM2.5 FEM Configuration Automated Equivalent Method: EQPM-0715-266 "Met One Instruments, Inc. BAM-1020 Beta Attenuation Mass Monitor - PM25 FEM Configuration," configured for 24 1- hour average measurements of PM2 5 by beta attenuation, using a glass fiber filter tape roll (460130 or 460180) and a sample flow rate of 16.67 liters/min and with the standard EPA PM10 inlet (meeting 40 CFR 50 Appendix L specifications) and with a URG-2000-30EGN PM25 (BX-809) cyclonic separator, BX-596 combo T/RH sensor, BX-827 (110V) or BX-830 (230 V). Instrument must be operated in accordance with the BAM 1020 Particulate Monitor operation manual, revision L or later. Instrument must be operated with firmware revision 3.2.4 or later. This PM2.5 equivalent method designation only applies to the BAM-1020 configured with the URG-2000-30EGN cyclone. Federal Register: Vol. 80, page 51802, 8/26/2015 Met One Instruments, Inc. BAM-1022 Real Time Beta Attenuation Mass Monitor-Outdoor PM2.5 FEM Configuration Automated Equivalent Method: EQPM-1013-209 "Met One Instruments, Inc. BAM-1022 Beta Attenuation Mass Monitor - Outdoor PM2 5 FEM Configuration," configured for ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 13 24 1-hour average measurements of PM2 5 by beta attenuation, using a glass fiber filter tape roll (460130 or 460180) and a sample flow rate of 16.67 liters/min and with the standard (BX-802) EPA PMio inlet (meeting 40 CFR 50 Appendix L specifications) and with a BGI VSCC™ Very Sharp Cut Cyclone (BX-808) or Tisch TE-PM2.5C particle size separator, and equipped with external enclosure BX-922 and BX-592 ambient temperature sensor or BX-596 ambient temperature/barometric combination sensor or BX-597 ambient temperature/barometric pressure/relative humidity combination sensor. Instrument must be operated in accordance with the BAM 1022 Particulate Monitor operation manual, revision 3 or later. This designation applies to PM2 5 measurements only. Federal Register: Vol. 78, page 67360,11/12/2013 Latest modifications: 7/2014; 10/2015 Met One Instruments, Inc. E-FRM- PMzs Manual Reference Method: RFPS-0315-221 "Met One Instruments, Inc. E-FRM," configured for filter sampling of ambient particulate matter using the US EPA PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, equipped with either a BGI VSCC™ cyclone or WINS PM25 fractionator, with a flow rate of 16.67 L/min, using 47 mm PTFE membrane filter media, and operating with firmware version Rl.1.0 and later, and operated in accordance with the Met One E-FRM PM2 5 operating manual. Federal Register: Vol. 80, page 32114, 6/05/2015 Met One Instruments, Inc. E-FRM- PMzs Manual Equivalent Method: EQPS-0316-235 "Met One Instruments, Inc. E-FRM," configured for filter sampling of ambient particulate matter using the US EPA PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, equipped with a URG-2000-30EGN Cyclone particle size separator, and operated for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, using 47 mm PTFE membrane filter media, and operating with firmware version Rl.1.0 and later, and operated in accordance with the Met One E-FRM PM25 operating manual. Federal Register: Vol. 81, page 25397, 4/28/2016 Opsis SM200- Dust Monitor Automated Equivalent Method: EQPM-0812-203 "Opsis SM200- Dust Monitor" configured for PM25 with the US EPA PM10 inlet specified in 40 CFR 50 Appendix L, followed by a BGI Inc. Veiy Sharp Cut Cyclone (VSCC™) particle size separator, operated for a continuous 24-hour sample period at a total actual flow rate of 16.67 L/min. using 47mm PTFE membrane filters, a TS200 temperature stabilizer and software version 1.04.16 or later, in accordance with the Opsis SM200 Dust Monitor Operation and Instruction Guide. Federal Register: Vol. 77, page 55832, 09/11/2012 Rupprecht & Patashnick Partisol "-FRM Model 2000 PMzs Air Sampler Manual Reference Method: RFPS-0498-117 "Rupprecht & Patashnick Company, Incorporated Partisol®-FRM Model 2000 PM25 Air Sampler," operated with software versions 1.102 - 1.202, with either R&P-specified machined or molded filter cassettes, with or without the optional insulating jacket for cold weather operation, for a continuous 24-hour sample period, in accordance with the Model 2000 Instruction Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 63, page 18911, 04/16/1998 Rupprecht & Patashnick Partisol® Model 2000 PMz s Audit Sampler Manual Reference Method: RFPS-0499-129 "Rupprecht & Patashnick Company, Inc. Partisol® Model 2000 PM2 5 Audit Sampler," configured as a PM2 5 reference method and operated with software (firmware) version 1.2 - 1.202, for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, in accordance with the Partisol® Model 2000 Operating Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 64, page 19153, 04/19/1999 Rupprecht & Patashnick Partisol® Model 2000 PMz. s Audit Sampler Manual Reference Method: RFPS-0499-129 or Manual Equivalent Method: EQPM-0202-144 "Rupprecht & Patashnick Co., Inc. Partisol® Model 2000 PM2 5 FEM Audit Sampler," configured with a BGI VSCC™ Very Sharp Cut Cyclone particle size separator, and operated with software (firmware) version 1.2 - 1.202, for a continuous 24-hour ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 14 sample period at a flow rate of 16.67 liters/minute, in accordance with the Partisol® Model 2000 Operating Manual and VSCC™ supplemental manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 67, page 15567, 04/02/2002 Rupprecht & Patashnick Partisol91-Plus Model 2025 Sequential Air Sampler Manual Reference Method: RFPS-0498-118 "Rupprecht & Patashnick Company, Incorporated Partisol®-Plus Model 2025 PM25 Sequential Air Sampler," operated with any software version 1.003 through 1.4.16, with either R&P-specified machined or molded filter cassettes, for a continuous 24- hour sample period, in accordance with the Model 2025 Instruction Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 63, page 18911, 04/16/1998 Teledyne Model 602 BetaPLUS Particle Measurement System or SWAM 5a Dual Channel Monitor Automatic Equivalent Method: EQPM-0912-204 "Teledyne Model 602 Bcta'"/ ,;s Particle Measurement System" or "SWAM 5a Dual Channel Monitof' configured for 1-hour measurements of PM2.5 by beta attenuation, on either a single (Line A or B) or both sampling lines (Line A and B) simultaneously, using 47 mm glass fiber filters, at a sample flow set to 16.67 liters/min and software version 05-02.07.63 or later and with an inlet system comprised of a PM10 pre-impactor inlet (based on European PM10 inlet design) combined with a BGI VSCC™ PM2.5 cyclone separator. Operated in accordance with the Teledyne Model 602 BetaPLUS Particle Measurement System Operation Manual. Federal Register: Vol. 77, page 60985,10/5/2012 Teledyne Advanced Pollution Instrumentation Model T640 PM Mass Monitor Automatic Equivalent Method: EQPM-0516-236 "Teledyne Advanced Pollution Instrumentation Model T640 PM mass monitor," continuous ambient particulate monitor operated at a volumetric flow rate of 5.0 Lpm, equipped with a TAPI 5-Lpm sample inlet (P/N: 081050000), TAPI aerosol sample conditioner (P/N: 081040000), configured for operation with firmware version 1.0.2.126 or later, and operated in accordance with the Teledyne Model T640 Operations Manual. This designation applies to PM2 5 measurements only. Federal Register: Vol. 81, page 45285, 07/13/2016 Teledyne Advanced Pollution Instrumentation Model T640 PM Mass Monitor with 640X Option Automatic Equivalent Method: EQPM-0516-238 "Teledyne Advanced Pollution Instrumentation Model T640 PM mass monitor with 640X option," continuous ambient particulate monitor operated at a volumetric flow rate of 16.67 Lpm equipped with the louvered PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, TAPI aerosol sample conditioner (P/N: 081040000), configured for operation with firmware version 1.0.2.126 or later, in accordance with the Teledyne Model T640 Operations Manual. This designation applies to PM2.5 measurements only. Federal Register: Vol. 81, page 45285, 07/13/2016 Thermo Electron Model RAAS2.5-100 PM2.5 Ambient Air Sampler Manual Reference Method: RFPS-0598-119 or Manual Equivalent Method: EQPM-0804-153 "Thermo Electron Corporation Model RAAS2.5-100 FEM PM2 5 Ambient Air Sampler," configured with a BGI VSCC™ Very Sharp Cut Cyclone particle size separator and operated with software version 06.0B.00 configured for "Single 2.5" operation, for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, in accordance with the Model RAAS2.5-100 FEM Operator's Manual and VSCC™ supplemental manual, and in accordance with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 69, page 47924, 08/06/2004 Thermo Electron Model RAAS2.5-200 PM2. s Audit Air Sampler Manual Reference Method: RFPS-0299-128 or Manual Equivalent Method: EQPM-0804-154 "Thermo Electron Corporation Model RAAS2.5-200 FEM PM2 5 Audit Air Sampler," configured with a BGI VSCC™ Very Sharp Cut Cyclone particle size separator and operated with software version 06.0B.00, for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, in accordance with the Model RAAS2.5-200 FEM Operator's Manual and VSCC™ supplemental manual, and in accordance with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 69, page 47924, 08/06/2004 ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 15 Thermo Electron Model RAAS2.5-300 PM2.5 Sequential Ambient Air Sampler Manual Reference Method: RFPS-0598-120 or Manual Equivalent Method: EQPM-0804-155 "Thermo Electron Corporation Model RAAS2.5-300 FEM PM25 Sequential Ambient Air Sampler," configured with a BGI VSCC™ Very Sharp Cut Cyclone particle size separator and operated with software version 06.0B.00 configured for "Multi 2.5" operation, for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, in accordance with the Model RAAS2.5-300 FEM Operator's Manual and VSCC™ supplemental manual, and in accordance with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 69, page 47924, 08/06/2004 Thermo Environmental Instruments, Incorporated Model 605 "CAPS" Sampler Manual Reference Method: RFPS-1098-123 "Thermo Environmental Instruments, Incorporated Model 605 "CAPS" Computer Assisted Particle Sampler," configured as a PM2.5 reference method and operated with software version 1.02 A, for a continuous 24-hour sample period, in accordance with the Model 605 Instruction Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 63, page 58036,10/29/1998 Thermo Scientific Model 5014i or Thermo Scientific FH62C14-DHS Continuous Ambient Particle Monitor Automated Equivalent Method: EQPM-0609-183 "Thermo Scientific Model 5014i or FH62C14-DHS Continuous Ambient Particle Monitor," operated at a flow rate of 16.67 liters per minute for 24-hour average measurements configured for PM2 5 with a louvered PM10 size selective inlet as specified in 40 CFR 50 Appendix L, Figs. L-2 through L-19, aPM2.5 BGI Inc. Very Sharp Cut Cyclone (VSCC™) particle size separator, inlet connector, sample tube, DHS heater with 35% RH threshold, mass foil kit, GF10 filter tape, 8-hour filter change, and operational calibration and servicing as outlined in the 5014i Continuous Ambient Particulate Monitor or FH62C14-DHS Continuous Ambient Particulate Monitor operating manual. Federal Register: Vol. 74, page 28696, 06/17/2009 Latest modification: 03/2010 Thermo Scientific Model 5030i SHARP Monitor or Model 5030 SHARP Monitor Automated Equivalent Method: EQPM-0609-184 "Thermo Scientific Model 5030 SHARP Monitor," operated at a flow rate of 16.67 liters per minute for 24-hour average measurements configured for PM2 5 with a louvered PM10 size selective inlet as specified in 40 CFR 50 Appendix L, Figs. L-2 through L-19, a PM2 5 BGI Inc. Very Sharp Cut Cyclone (VSCC™) particle size separator, inlet connector, sample tube, DHS heater with 58% RH threshold, mass foil kit, GF10 filter tape, nephelometer zeroing kit, 8-hour filter change, and operational calibration and servicing as outlined in the Model 5030i or Model 5030 SHARP instructional manual. Federal Register: Vol. 74, page 28696, 06/17/2009 Latest modification: 06/2013 Thermo Scientific TEOM® 1400a Ambient Particulate Monitor with Series 8500C FDMS®; Thermo Scientific TEOM® 1405-F Ambient Particulate Monitor with FDMS* Automated Equivalent Method: EQPM-0609-181 "Thermo Scientific TEOM® 1400a Ambient Particulate Monitor with Series 8500C FDMS® (Filter Dynamics Measurement System) or Thermo Scientific TEOM® 1405-F Ambient Particulate Monitor with FDMS®," configured for PM2 5 with the US EPA PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, followed by a BGI Inc. Very Sharp Cut Cyclone (VSCC™) particle size separator, operated with a total actual flow of 16.67 L/min., loaded with Series FDMS® 8500 module operating software and an FDMS® kit. TEOM® 1400a with Series 8500C FDMS® operated with firmware version 3.20 and later and TEOM® 1405-F with FDMS® operated with version 1.55 or later and according to the appropriate operating manual. Federal Register: Vol. 74, page 28696, 06/17/2009 Latest Modification: 09/2010 Thermo Scientific TEOM® 1405-DFDichotomous Ambient Particulate Monitor with FDMS* Automated Equivalent Method: EQPM-0609-182 "Thermo Scientific TEOM® 1405-DF Dichotomous Ambient Particulate Monitor with FDMS®," configured for dual filter sampling of fine (PM2 5) and coarse particles using the US EPA PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19 and a virtual impactor, with a total flow rate of 16.67 L/min, fine sample flow of 3 L/min, and coarse sample flow rate of 1.67 L/min, and operating with firmware version 1.50 and later, operated with or without external enclosures, and operated in ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 16 accordance with the Thermo Scientific TEOM® 1405-DF Dichotomous Ambient Particulate Monitor Instruction Manual. This designation applies to PM2 5 measurements only. Federal Register: Vol. 74, page 28696, 06/17/2009 Thermo Scientific Partisol" 2000-D Dichotomous Air Sampler or Thermo Fisher Scientific Partisol" 2000i-D Dichotomous Air Sampler Manual Equivalent Method: EQPS-0509-177 "Thermo Scientific Partisol® 2000-D Dichotomous Air Sampler" or "Thermo Fisher Scientific Partisol® 2000/-D Dichotomous Air Sampler," configured for dual-filter, single-event sampling of fine (PM2 5) and coarse (PMi 0-2.5) particles, operated with a U.S. EPA PMi0 inlet and using a virtual impactor to separate fine and coarse PM into two samples for collection on two separate filter membranes, for a 24-hour sampling period, in accordance with the Partisol® 2000-D or Partisol® 2000/-D instruction manual, as appropriate. Partisol® 2000/-D operated with firmware version 2.0 or greater. Federal Register: Vol. 74, page 26395, 06/02/2009 Latest modification: 06/2011 Thermo Scientific Partisol-Plus 2025-D Dichotomous Sequential Air Sampler or Thermo Fisher Scientific Partisol® 2025i-D Dichotomous Sequential Air Sampler Manual Equivalent Method: EQPS-0509-179 "Thermo Scientific Partisol®-Plus 2025-D Dichotomous Sequential Air Sampler" or "Thermo Fisher Scientific Partisol® 2025/'- D Dichotomous Sequential Air Sampler," configured for dual-filter sampling of fine (PM25) and coarse (PMi 0-2.5) particle components, with a U.S. EPA PM10 inlet and using a virtual impactor to separate the fine and coarse PM into two samples for collection on two separate filter membranes, and operated with the modified filter shuttle mechanism implemented May 31, 2008, and firmware version 1.500 or greater for the Partisol®-Plus 2025-D and version 2.0 or greater for the Partisol® 2025/'- D, for continuous 24-hour sample period , in accordance with the Partisol®-Plus 2025-D or Partisol® 2025/-D instruction manual, as appropriate. Federal Register: Vol. 74, page 26395, 06/02/2009 Latest modification: 06/2011 Thermo Scientific Partisol ' 2000-FRM PM2.5 Air Sampler or Thermo Fisher Scientific Partisol® 2000i PM 2.5 Air Sampler or Rupprecht & Patashnick Partisol" -FRM 2000 PM2. s Air Sampler Manual Reference Method: RFPS-0498-117 or Manual Equivalent Method: EQPM-0202-143 "Thermo Scientific Partisol® 2000-FRM PM2.5 Air Sampler" or "Thermo Fisher Scientific Partisol® 2000i PM2.5 Air Sampler" or "Rupprecht & Patashnick Partisol®-FRM 2000 PM2 5 [FEM] Air Sampler configured with a BGI VSCC™ Very Sharp Cut Cyclone particle size separator with either R&P-specified machined or molded filter cassettes, for 24-hour continuous sampling periods, in accordance with the Partisol® 2000-FRM or Partisol®2000/' Instruction Manual, as appropriate, and VSCC™ supplemental manual. Partisol® 2000-FRM operated with software versions 1.102 through 1.202 and Partisol® 2000i with firmware version 2.0 or greater. Method is operated with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L, and with or without the optional insulating jacket for cold weather operation. Federal Register: Vol. 67, page 15567, 04/02/2002 Latest modification: 06/2011 Thermo Scientific Partisol"-Plus 2025 Sequential PM2.5 Air Sampler or Thermo Fisher Scientific Partisol® 2025i Sequential PMisAir Sampler or Rupprecht & Patashnick Partisol®-Plus 2025 PM2 5 Sequential Sampler Manual Reference Method: RFPS-0498-118 or Manual Equivalent Method: EQPM-0202-145 "Thermo Scientific Partisol®-Plus 2025 PM2.5 Sequential Air Sampler" or "Thermo Fisher Scientific Partisol® 2025/ PM2.5 Sequential Air Sampler" or "Rupprecht & Patashnick Partisol®-Plus 2025 PM2 5 (FEM) Sequential Air Sampler," configured with a BGI VSCC™ Very Sharp Cut Cyclone particle size separator with either R&P-specified machined or molded filter cassettes, for 24-hour continuous sampling periods. Partisol®-Plus 2025 to be operated with any software version 1.003 through 1.5 and Partisol® 2025/ with firmware version 2.0 or greater, and with the modified filter shuttle mechanism. Method to be operated in accordance with the Partisol®-Plus 2025 or Partisol® 2025/ instruction manual, as appropriate, with the VSCC™ supplemental manual, and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 67, page 15567, 04/02/2002 Latest modification: 06/2011 Tisch Environmental Model TE-Wilbur2.5 Particulate Sampler - PM2 5 Manual Reference Method: RFPS-1014-219 "Tisch Environmental Model TE-Wilbur2.5 PM2.5 Low-Volume Air Particulate Sampler," configured as a PM2.5 reference ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 17 method, operated with software version 3.5 or earlier and a TE-PM10-D PMio size-selective inlet as specified in 40 CFR 50 Appendix L Figs. L-2 thru L-19, with either a BGIVSCC™ Very Sharp Cut Cyclone particle size separator or WINS impactor or Tisch Environmental TE-PM2.5C cyclone, and operated for 24 sample periods at a flow rate of 16.67 L/min, using 47 mm PTFE membrane filter media, operated with or without the optional TE-W-600 Solar Panel Power Supply kit, and in accordance with the Tisch Environmental Model TE-Wilbur2.5 PM2 5 Low-Volume Air Particulate Sampler instruction manual and with the requirements and sample collection filters as specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 79, page 65392,11/04/2014 Latest modification: 6/2015; 11/2016 Tisch Environmental Model TE-Wilbur2.5 Particulate Sampler - PM2 s Manual Equivalent Method: EQPS-0415-223 "Tisch Environmental Model TE-Wilbur2.5 PM2 5 Low-Volume Air Particulate Sampler," configured as a PM2 5 equivalent method, operated with software version 3.5 or earlier and a TE-PM10-D PM10 size-selective inlet as specified in 40 CFR 50 Appendix L Figs. L-2 thru L-19, configured with a Tisch TE-PM2.5C particle size separator and operated for a continuous 24-hour sample period at a flow rate of 16.67 L/min, using 47 mm PTFE membrane filter media, operated with or without the optional TE-W-600 Solar Panel Power Supply kit, and in accordance with the Tisch Environmental Model TE-Wilbur2.5 PM2 5 Low-Volume Air Particulate Sampler instruction manual and with the requirements and sample collection filters as specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 80, page32114, 6/05/2015 URG-MASS100 Single PMzs Sampler Manual Reference Method: RFPS-0400-135 "URG-MASS100 Single PM2 5 FRM Sampler," operated with software (firmware) version 4B or 5.0.1, configured for "Single 2.5" operation with either a BGI Very Sharp Cut Cyclone (VSCC™) particle size separator or WINS impactor, and operated for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute and in accordance with the URG-MASS 100 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol 65, page 26603, 05/08/2000 URG-MASS300 Sequential PMzs Sampler Manual Reference Method: RFPS-0400-136 "URG-MASS300 Sequential PM25 FRM Sampler," operated with software (firmware) version 4B or 5.0.1, configured for "Multi 2.5" operation with either a BGI Very Sharp Cut Cyclone (VSCC™) particle size separator or WINS impactor and operated for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, and in accordance with the URG- MASS300 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 65, page 26603, 05/08/2000 URG-MASS100 Single PMzs Sampler Manual Equivalent Method: EQPS-0316-233 "URG-MASS100 Single PM25 Sampler," operated with software (firmware) version 4B or 5.0.1, configured for "Single 2.5" operation with a URG-2000-30EGN Cyclone particle size separator, and operated for a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, and in accordance with the URG-MASS100 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol. 81, page 25397, 04/28/2016 URG-MASS300 Sequential PMzs Sampler Manual Equivalent Method: EQPS-0316-234 "URG-MASS300 Sequential PM2 5 Sampler," operated with software (firmware) version 4B or 5.0.1, configured for "Multi 2.5" operation with a URG-2000-30EGN Cyclone particle size separator, and operated a continuous 24-hour sample period at a flow rate of 16.67 liters/minute, and in accordance with the URG-MASS300 Operator's Manual and with the requirements and sample collection filters specified in 40 CFR Part 50, Appendix L. Federal Register: Vol 81, page 25397, 04/28/2016 ------- PMio-2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 18 Particulate Matter - PM10-2.5 BGI Incorporated Model PQ200 Sampler Pair Manual Reference Method: RFPS-1208-173 "BGI Incorporated Model PQ200 PMi0-2.5 Sampler Pair," for the determination of coarse particulate matter as PMi0-2.5 consisting of a pair of BGI Model PQ200 samplers, with one configured for sampling PM25 (RFPS-0498-116) and the other configured for sampling PMi0c (RFPS-1298-125) with the PM2 5 separator replaced with a BGI WINS Eliminator and operated in accordance with the Model PQ200 Instruction manual supplement Appendix O. Federal Register: Vol. 73, page 77024,12/18/2008 Met One Instruments BAM-1020 PM10-2.5 Measurement System Automated Equivalent Method: EQPM-0709-185 "Met One Instruments BAM-1020 PM10-2.5 Measurement System," consisting of 2 BAM-1020 monitors, the first of which (PM25 measurement) is configured as a PM2.5 FEM (EQPM-0308-170). The second BAM-1020 monitor (PM10 measurement) is configurable as a PM2.5 FEM (EQPM-0308-170), but set to monitor PM10. The BAM-1020 monitors are collocated to within 1-4 meters of one another. The BAM-1020 performing the PM2.5 measurement is equipped with Met One Instruments, Inc. P/N BX-Coarse interface board and accessories; the units are interconnected to provide concurrent sampling and to report PMi 0-2.5 concentrations directly to the user. Both units are operated in accordance with BAM-1020 PM-Coarse Addendum Rev. 5-5 or later and the BAM-1020 Operations Manual Rev. D or later. Federal Register: Vol. 74, page 28241, 06/15/2009 Met One Instruments, Inc. E-FRM- PM10 and E-FRM- PM2.5 Sampler Pair Manual Reference Method: RFPS-0316-232 "Met One Instruments, Inc. E-FRM- PM10 and E-FRM- PM2.5 Sampler Pair" for the determination of coarse particulate matter as PMi 0-2.5, consisting of a pair of Met One Instruments, Inc. E-FRM samplers, with one being the E-FRM PM2 5 sampler (RFPS-0315-221) and the other being the E-FRM PM10 sampler (RFPS-0216-231). The units are collocated to within 1-4 meters of one another. Both units are operated in accordance with the associated E-FRM instruction manual. This designation applies to PMi 0-2.5 measurements only. Federal Register: Vol. 81, page 25397, 04/28/2016 Teledyne Model 602 BetaPLUS Particle Measurement System or SWAM 5a Dual Channel Monitor Automated Equivalent Method: EQPM -0912-206 "Teledyne Model 602 Bcta'"/ , :s Particle Measurement System" or "SWAM 5a Dual Channel Monitor" configured for 1-hour measurements of PM10 and PM2.5 by beta attenuation, with the standard, louvered US EPA PM10 size selective inlet specified in 40 CFR 50 Appendix L on one channel (Line A or B) and with an inlet system comprised of a PM10 pre-impactor inlet (based on European PM10 inlet design) combined with a BGI VSCC™ PM2 5 cyclone separator on the second channel (Line A or B, but always with PM10 on the opposite Line). The PMi0-2.5 mass measurement is performed using the resultant subtraction of PM10 minus PM2 5. Operated in accordance with the Teledyne Model 602 Bcta'"/ , :s Particle Measurement System Operation Manual. Federal Register: Vol. 77, page 60985,10/5/2012 Teledyne Advanced Pollution Instrumentation Model T640 PM Mass Monitor with 640X Option Automated Equivalent Method: EQPM-0516-240 "Teledyne Advanced Pollution Instrumentation Model T640 PM mass monitor with 640X option," continuous ambient particulate monitor operated at a volumetric flow rate of 16.67 Lpm, equipped with the louvered PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19, TAPI aerosol sample conditioner (P/N: 081040000), configured for operation with firmware version 1.0.2.126 or later, in accordance with the Teledyne Model T640 Operations Manual. This designation applies to PMi 0-2.5 measurements only. Federal Register: Vol. 81, page 45285, 07/13/2016 Thermo Scientific Partisol" 2000-D Dichotomous Air Sampler or Thermo Fisher Scientific Partisol" 2000i-D Dichotomous Air Sampler Manual Equivalent Method: EQPS-0509-178 "Thermo Scientific Partisol® 2000-D Dichotomous Air Sampler" or "Thermo Fisher Scientific Partisol® 2000/-D Dichotomous Air Sampler," configured for dual-filter, single-event sampling of fine (PM2.5) and coarse (PMi 0-2.5) particles, operated with a ------- PMio-2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 19 U.S. EPA PMio inlet and using a virtual impactor to separate fine and coarse PM into two samples for collection on two separate filter membranes, for a 24-hour sampling period, in accordance with the Partisol® 2000-D or Partisol® 2000/-D instruction manual, as appropriate. Partisol® 2000/-D operated with firmware version 2.0 or greater. Federal Register: Vol. 74, page 26395, 06/02/2009 Latest modification: 06/2011 Thermo Scientific Partisol-Plus 2025-D Dichotomous Sequential Air Sampler or Thermo Fisher Scientific Partisol9 2025i- D Dichotomous Sequential Air Sampler Manual Equivalent Method: EQPS-0509-180 "Thermo Scientific Partisol®-Plus 2025-D Dichotomous Sequential Air Sampler" or "Thermo Scientific Partisol® 2025/-D Dichotomous Sequential Air Sampler," configured for dual-filter sampling of fine (PM25) and coarse (PMi 0-2.5) particle components, with a U.S. EPA PM10 inlet and using a virtual impactor to separate the fine and coarse PM into two samples for collection on two separate filter membranes, and operated with the modified filter shuttle mechanism implemented May 31, 2008, and firmware version 1.500 or greater for the Partisol®-Plus 2025-D and version 2.0 or greater for the Partisol® 2025/'- D, for 24-hour continuous sampling periods, in accordance with the Partisol®-Plus 2025-D or Partisol® 2025/-D instruction manual, as appropriate. Federal Register: Vol. 74, page 26395, 06/02/2009 Latest modification: 06/2011 Thermo Scientific Partisol® 2000-FRM PM10-2.5 Sampler Pair or Thermo Fisher Scientific Partisol!® 2000i PM10-2.5 Air Sampler Pair Manual Reference Method: RFPS-0509-175 "Thermo Scientific Partisol® 2000-FRM PM10-2.5 Sampler Pair" or "Thermo Fisher Scientific Partisol® 2000/ PMi 0-2.5 Air Sampler Pair," for the determination of coarse particulate matter as PMi 0-2.5, consisting of a pair of Thermo Scientific Partisol® 2000-FRM or 2000/ samplers, with one configured as a PM2 5 sampler (RFPS-0498-117) and the other configured as a PMioc sampler with the PM2 5 separator replaced with a Thermo Scientific WINS bypass downtube (RFPS-1298-126), with U.S. EPA PM10 inlets on both samplers and operated in accordance with the Partisol® 2000-FRM or 2000/ instruction manual supplement, as appropriate, and the 2000/ operated with firmware version 2.0 or greater. Federal Register: Vol. 74, page 26395, 06/02/2009 Latest modification: 06/2011 Thermo Scientific Partisol"-Plus 2025 Sequential PM10-2.5 Air Sampler Pair or Thermo Fisher Scientific Partisol® 2025i Sequential PMio-is Air Sampler Pair Manual Reference Method: RFPS-0509-176 "Thermo Scientific Partisol®-Plus 2025 Sequential PM10-2.5 Air Sampler Pair" or "Thermo Fisher Scientific Partisol® 2025/ Sequential PMi 0-2.5 Air Sampler Pair," for the determination of coarse particulate matter as PM10-2.5, consisting of a pair of Thermo Scientific Partisol®-Plus 2025 sequential samplers or a pair of Thermo Fisher Scientific Partisol® 2025/ sequential samplers, with one configured as a PM2 5 sampler (RFPS-0498-118) and the other configured as a PMi0c sampler with the PM2 5 separator replaced with a Thermo Scientific Partisol® 2025 downtube (RFPS-1298-127). Partisol®-Plus 2025 to be operated with any software version 1.003 through 1.5 and Partisol® 2025/ with firmware version 2.0 or greater, with the modified filter shuttle mechanism. Method to be operated in accordance with the Partisol®-Plus 2025 or Partisol® 2025/ instruction manual supplement, as appropriate. Federal Register: Vol. 74, page 26395, 06/02/2009 Latest modification: 06/2011 Thermo Scientific TEOM® 1405-DFDichotomous Ambient Particulate Monitor with FDMS® Automated Equivalent Method: EQPM-1013-207 "Thermo Scientific TEOM® 1405-DF Dichotomous Ambient Particulate Monitor with FDMS®," configured for dual filter sampling of fine (PM2 5) and coarse particles using the US EPA PM10 inlet specified in 40 CFR 50 Appendix L, Figs. L-2 thru L-19 and a virtual impactor, with a total flow rate of 16.67 L/min, fine sample flow of 3 L/min, and coarse sample flow rate of 1.67 L/min, and operating with firmware version 1.70 and later, operated with or without external enclosures, and operated in accordance with the Thermo Scientific TEOM® 1405-DF Dichotomous Ambient Particulate Monitor Instruction Manual. This designation applies to PMi 0-2.5 measurements only. Federal Register: Vol. 78, page 67360,11/12/2013 Tisch Environmental Model TE- Wilbur Low- Volume Air Particulate Sampler Pair Manual Reference Method: RFPS-1014-220 "Tisch Environmental Model TE-Wilbur Low-Volume Air Particulate Sampler Pair" for the determination of coarse particulate matter as PMi0-2.5, consisting of a pair of Tisch Environmental Model TE-Wilbur samplers, with one being the TE-Wilbur2.5 ------- PMio-2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 20 PM2.5 sampler (RFPS-1014-219) and the other being a TE-WilburlO PM10 sampler (RFPS-0714-216), and operated in accordance with the associated TE-Wilbur instruction manual. This designation applies to PMi0-2.5 measurements only. Federal Register: Vol. 79, page 65392,11/04/2014 Latest modification: 11/2016 Tisch Environmental Model TE-Wilbur2.5 and TE-WilburlO Sampler Pair Manual Equivalent Method: EQPS-0415-224 "Tisch Environmental Model TE-Wilbur Low-Volume Air Particulate Sampler Pair" for the determination of coarse particulate matter as PMi0-2.5, consisting of a pair of Tisch Environmental Model TE-Wilbur samplers, with one being the TE-Wilbur2.5 PM2.5 sampler with TE-PM2.5C particle size separator (EQPS-0415-223) and the other being a TE-WilburlO PM10 sampler (RFPS-0714-216), and operated in accordance with the associated TE-Wilbur instruction manual. This designation applies to PM10-25 measurements only. Federal Register: Vol 80, page 32114, 6/05/2015 ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 21 Sulfur Dioxide Reference Method for S02 (Pararosaniline Method) Manual Reference Method: 40 CFR Part 50, Appendix A Reference Method for the Determination of Sulfur Dioxide in the Atmosphere (Pararosaniline Method) Federal Register: Vol. 47, page 54899,12/06/1982 and Vol 48,17355, 04/22/1983 Pararosaniline Method for S02 - Technicon I Manual Equivalent Method: EQS-0775-001 "Pararosaniline Method for the Determination of Sulfur Dioxide in the Atmosphere-Technicon I Automated Analysis System" Federal Register: Vol. 40, page 34024, 08/13/1975 Pararosaniline Method for S02 - Technicon II Manual Equivalent Method: EQS-0775-002 "Pararosaniline Method for the Determination of Sulfur Dioxide in the Atmosphere-Technicon II Automated Analysis System" Federal Register: Vol. 40, page 34024, 08/13/1975 Advanced Pollution Instrumentation, Inc. Model 100 S02 Analyzer Automated Equivalent Method: EQSA-0990-077 "Advanced Pollution Instrumentation, Inc. Model 100 Fluorescent SO2 Analyzer," operated on the 0-0.1 ppm1, the 0-0.2 ppm1, the 0-0.5 ppm, or the 0-1.0 ppm range with a 5-micron TFE filter element installed in the rear-panel filter assembly, either a user- or vendor-supplied vacuum pump capable of providing 20 inches of mercury vacuum at 2.5 L/min, with or without any of the following options: Internal Zero/Span; Pump Pack; Rack Mount With Slides; RS-232 Interface; Status Output; TFE Zero/Span Valves; Zero Air Scrubber; Dual Range.2 Federal Register: Vol. 55, page 38149, 09/17/1990 ASARCO Model 500 S02 Monitor Automated Equivalent Method: EQSA-0877-024 "ASARCO Model 500 Sulfur Dioxide Monitor," operated on a 0-0.5 ppm range; or "ASARCO Model 600 Sulfur Dioxide Monitor," operated on a 0-1.0 ppm range. (Both models are identical except for the range.) NOTE: This method is no longer commercially available. Federal Register: Vol. 42, page 44264, 09/02/77 and Vol 44, page 67522,11/26/1979 Beckman Model 953 Fluorescent Ambient S02 Analyzer Automated Equivalent Method: EQSA-0678-029 "Beckman Model 953 Fluorescent Ambient SO2 Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with a time constant setting of 2, 2.5, or 3 minutes, a 5 to 10 micron membrane filter element installed in the rear-panel filter assembly, with or without any of the following options: Remote Operation Kit, Catalog No. 641984; Digital Panel Meter, Catalog No. 641710; Rack Mount Kit, Catalog No. 641709; Panel Mount Kit, Catalog No. 641708. Federal Register: Vol. 43, page 35995, 08/14/1978 Bendix Model 8303 Sulfur Analyzer Automated Equivalent Method: EQSA-1078-030 "Bendix Model 8303 Sulfur Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with a Teflon filter installed on the sample inlet of the H2S scrubber assembly. Federal Register: Vol. 43, page 50733,10/31/1978 Columbia Scientific Industries Model 5700 SO2 Analyzer Automated Equivalent Method: EQSA-0494-095 "Columbia Scientific Industries Model 5700 Sulfur Dioxide Analyzer," operated with software version 1.0 on any full scale range between 0-250 ppb1 and 0-1000 ppb, at any integration time setting from 20 to 99 seconds, at any temperature in the range of 15°C to 30°C, at any AC line voltage in the range of 105 to 130 volts, and with or without any of the following options: 964-0121 Alarm Relay Contacts 964-0125 Dual Current Outputs 964-0131 Rack Mount 964-0122 Input Solenoids 964-0126 Printer 964-0012 Single Headed Pump 964-0124 Dual Analog Voltage Outputs Federal Register: Vol. 59, page 18818, 04/20/1994 ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 22 Dasibi Model 4108 U. V. Fluorescence SO2 Analyzer Automated Equivalent Method: EQSA-1086-061 "Dasibi Model 4108 U.V. Fluorescence SO2 Analyzer," operated with a range of 0-100 ppb1, 0-200 ppb1, 0-500 ppb, or 0-1000 ppb, with a Teflon-coated particulate filter and continuous hydrocarbon removal system, with or without any of the following options: Rack Mounting Brackets and Slides; RS-232-C Interface; Temperature Correction. Federal Register: Vol. 51, page 32244, 09/10/1986 DKK-TOA Corp. Model GFS-32 U.V. FluorescentSO2Analyzer Automated Equivalent Method: EQSA-0701-115 "DKK-TOA Corporation Model GFS-32 Ambient Air SO2 Ultraviolet Fluorescent Analyzer," operated within the 0.000 to 0.500 ppm range in the temperature range of 20°C to 30°C. Federal Register: Vol. 62, page 44007, 08/18/1997 DKK-TOA Corp. Model GFS-112E U. V. Fluorescent SO2 Analyzer Automated Equivalent Method: EQSA-0100-133 "DKK-TOA Corporation Models GFS-112E and GFS-112E-1 U.V. Fluorescence SO2 Analyzer," operated at any temperature ranging from 15°C to 35°C, on any of the following measurement ranges: 0-0.05 ppm1, 0-0.100 ppm1, 0-0.200 ppm1, 0-0.5 ppm, or 0-1.000 ppm, and with or without the optional Internal zero air supply and permeation tube oven.2 Federal Register: Vol. 65, page 2610, 01/18/2000 DKK-TOA Corp. Model GFS-312E Ambient SO2 Analyzer Automated Equivalent Method: EQSA-1107-168 "DKK-TOA Corporation Model GFS-312E Ambient SO2 Analyzer," operated at any environmental temperature in the range of 20°C to 30°C on any of the following measurement ranges1: 0-0.1 ppm, 0-0.2 ppm and 0-0.5 ppm.2 Federal Register: Vol. 72, page 63176,11/08/2007 Ecotech Serinus 50 Sulfur Dioxide Analyzer or Opsis AB OPS50 Sulfur Dioxide Analyzer or Teledyne Analytical Instruments 6400E Sulfur Dioxide Analyzer or Tisch Environmental TE 2.0 Sulfur Dioxide Analyzer Automated Equivalent Method: EQSA-0809-188 "Ecotech Serinus 50 Sulfur Dioxide Analyzer" or "Opsis AB OPS50 Sulfur Dioxide Analyzer" or "Teledyne Analytical Instruments 6400E Sulfur Dioxide Analyzer" or "Tisch Environmental TE 2.0 Sulfur Dioxide Analyzer," operated in the range of 0-0.5 ppm, with a five-micron Teflon® filter element installed, and with the following selected: Background-Enabled, Control Loop-Enabled, Diagnostic Mode-Operate, Pres/Temp/Flow Compensation-Enabled, Span Compensation-Disabled, with concentration automatically corrected for temperature and pressure changes, and operated according to the Serinus 50 Sulfur Dioxide Analyzer User Manual or the Opsis OPS50 Sulfur Dioxide Analyzer User Manual or the Teledyne Analytical Instruments 6400E Sulfur Dioxide Analyzer Instruction Manual or the Tisch Environmental TE 2.0 Sulfur Dioxide Analyzer Instruction Manual, as appropriate. Federal Register: Vol. 74, page 38184, 07/31/2009 Latest Modifications: 05/2010, 05/2011, 05/2012, 8/2014 Environnement S.A. Model AF21M SO2 Analyzer Automated Equivalent Method: EQSA-0292-084 "Environnement S.A Model AF21M Sulfur Dioxide Analyzer," operated on a range of 0-0.5 ppm with a response time coefficient setting of 01, a Teflon filter installed in the rear-panel filter assembly, and with or without any of the following options: Rack Mount/Slides; RS-232-C Interface. Federal Register: Vol. 57, page 5444, 02/14/1992 ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 23 Environnement S.A. Model AF22M or AF22e SO2 Analyzer Automated Equivalent Method: EQSA-0802-149 "Environnement S. A Model AF22M or AF22eUV Fluorescence Sulfur Dioxide Analyzer," operated with a Ml scale range of 0 - 500 ppb, at any temperature in the range of 10°C to 35°C, with a 5-micron PTFE sample particulate filter, with automatic response time, with the automatic "ZERO-REF" cycle ON and set for activation every 24 hours, and with or without either of the following options: Permeation oven, ESTEL analog input/output board and LCD color touch screen.2 Federal Register: Vol. 67, page 57811, 09/12/2002 Environnement S.A. SANOA Multigas Longpath Monitoring System Automated Equivalent Method: EQSA-0400-138 "Environnement S.A. Model SANOA Multigas Longpath Air Quality Monitoring System," consisting of a receiver, one or more projectors, interface unit, a user-provided control unit computer running the SANOA VisionAIR software, and associated incidental equipment; configured for measuring SO2, with the temperature control and internal calibration cell options installed, operated with a measurement range of 0 to 0.5 ppm, over an installed monitoring path length of between 27 and 500 meters, within an ambient air temperature range of -30 to +45°C, with a measurement (integrating) time of 180 seconds, and with or without external temperature and barometric pressure sensors or any of the following options: external (meteo) input connection, series 1M bus connection, OGR type projector, analog outputs. Federal Register: Vol. 65, page 26603, 05/08/2000 Horiba Models APSA-360, APSA-360-CE, or APSA-360A-CE SO2 Monitors Automated Equivalent Method: EQSA-0197-114 "Horiba Instruments, Inc. Models APSA-360, APSA-360-CE or APSA-360A-CE Ambient Sulfur Dioxide Monitor," operated with a full scale range of 0 - 0.50 ppm, at any temperature in the range of 5°C to 40°C, with a Line Setting of "MEASURE," an Analog Output Setting of "MOMENTARY VALUE", and with or without any of the following options:21) Rack Mounting Plate and Side Rails, 2) RS-232 Communications Port, and 3) Internal zero gas and span gas generator. "Horiba Instruments, Inc. Model APSA-360A-CE Ambient Sulfur Dioxide Monitor," operated with one of the following measurement ranges: 0-0.05 ppm, 0-0.1 ppm, 0-0.2 ppm, 0-0.5 ppm or 0-1.0 ppm; with selectable time constants from 10 to 300 seconds; at any temperature in the range of 5°C to 40°C; and with or without the optional internal zero gas and span gas generator. Federal Register: Vol. 62, page 6968, 02/14/97; Vol 63, page 31992, 06/11/1998 Horiba Model APSA-3 70 Ambient SO 2 Monitor Automated Equivalent Method: EQSA-0506-159 "Horiba Instruments Incorporated Model APSA-370 Ambient SO2 Monitor," operated with a full scale fixed measurement range of 0 - 0.50 ppm, with the automatic range switching off, at any environmental temperature in the range of 20°C to 30°C.2 Federal Register: Vol. 71, page 25587, 05/01/2006 Lear Siegler Model AM2020 SO2 Monitor Automated Equivalent Method: EQSA-0486-049 "Lear Siegler Model AM2020 Ambient SO2 Monitor," operated on a range of either 0-0.5 or 0-1.0 ppm, at a wavelength of 299.5 nm, with a 5 minute integration period, over any 10°C temperature range between 20°C and 45°C, with or without the automatic zero and span correction feature. Federal Register: Vol. 45, page 79574,12/01/1980; Vol 46, page 9997, 01/30/1981 Lear Siegler Model SMI000 SO2 Monitor Automated Equivalent Method: EQSA-1275-005 "Lear Siegler Model SM1000 SO2 Ambient Monitor," operated on the 0-0.5 ppm range, at a wavelength of 299.5 nm, with the "slow" (300 second) response time, with or without any of the following options: SM-1 Internal Zero/Span; SM-2 Span Timer Card; SM-3 0-0.1 Volt Output; SM-4 0-5 Volt Output; SM-5 Alternate Sample Pump; SM-6 Outdoor Enclosure. Federal Register: Vol 41, page 3893, 01/27/1976; Vol 41, page 32946, 08/06/1976; Vol. 42, page 13044, 03/08/1977; Vol. 45, page 1147, 01/04/1980 ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 24 Meloy Model SA185-2A SO2 Analyzer Automated Equivalent Method: EQSA-1275-006 "Meloy Model SA185-2A Sulfur Dioxide Analyzer," operated on the 0-0.5 ppm range, with or without any of the following options: S-2 Modified Recorder Output S-5 Teflon-Coated Block S-6A Reignite Timer Circuit S-l 1A Manual Zero and Span S-35 Front Panel Digital Meter with BCD Output S-l3 Status Lights S-22A Remote Zero/Span Control S-14 Output Booster Amplifier S-23 Automatic Zero Adjust S-14B Line Transmitter Board S-23A Automatic/Manual Zero Adjust or operated on the 0-1.0 ppm range with either option S-36 or options S-l and S-24, with or without any of the other options. Federal Register: Vol. 41, page 3893, 01/27/1976 and Vol 43, page 38088, 08/25/1978 S-l Linearized Output S-24 Dual Range Linearized Output S-33 Remote Range Control and Status S-7 Press to Read Volt MeterS-34 Remote Control S-22 Remote Zero/Span Control and Status (Timer) S-l IB Automatic Zero and Span S-36 Dual Range Log-Linear Output S-38 Sampling Mode Status S-l8 Rack Mount Conversion S-18A Rack Mount Conversion S-21 Front Panel Digital (Signals) Meloy Model SA285E SO2 Analyzer Automated Equivalent Method: EQSA-1078-032 "Meloy Model SA285E Sulfur Dioxide Analyzer," operated on the following ranges and time constant switch positions: Range, ppb: 0-501 0-1001 0-500 0-1000 Time Constant Setting: 1 or 10 1 or 10 off, 1 or 10 off, 1 or 10 The analyzer may be operated at temperatures between 10°C and 40°C and at line voltages between 105 and 130 volts, with or without any of the following options: S-5 Teflon Coated Block S-14B Line Transmitter Board S-l8 Rack Mount Conversion S-18A Rack Mount Conversion S-21 Front Panel Digital Meter S-22 Remote Zero/Span Control and Status (Timer) S-22A Remote Zero/Span Control S-22B Remote Zero/Span Control and Status (Pulse) S-23 Auto Zero Adjust S-23A Auto/Manual Zero Adjust S-25 Press To Read S-26 Manual Zero and Span S-27 Auto Manual Zero/Span S-28 Auto Range and Status S-30 Auto Reignite S-32 Remote Range Control and Status S-35 Front Panel Digital Meter With BCD Output S-37 Temperature Status Lights S-38 Sampling Mode Status Federal Register: Vol. 43, page 50733,10/31/1978 Meloy Model SA 700 Fluorescence Sulfur Dioxide Analyzer Automated Equivalent Method: EQSA-0580-046 "Meloy Model SA 700 Fluorescence Sulfur Dioxide Analyzer," operated on the 0-250 ppb1, the 0-500 ppb, or the 0-1000 ppb range with a time constant switch position of either 2 or 3. The analyzer may be operated at temperatures between 20°C and 30°C and at line voltages between 105 and 130 volts, with or without any of the following options: FS-1 Current Output; FS-2 Rack Mount Conversion; FS-2A Rack Mount Conversion; FS-2B Rack Mount Conversion; FS-3 Front Panel Mounted Digital Meter; FS-5 Auto/Manual Zero/Span With Status; FS-6 Remote/Manual Zero/Span With Status; FS-7 Auto Zero Adjust. Federal Register: Vol. 45, page 31488, 05/13/1980 Monitor Labs Model 8450 Sulfur Monitor Automated Equivalent Method: EQSA-0876-013 "Monitor Labs Model 8450 Sulfur Monitor," operated on a range of either 0-0.5 or 0-1.0 ppm, with a 5 second time constant, a model 8740 hydrogen sulfide scrubber in the sample line, with or without any of the following options: BP Bipolar Signal Processor; IZS Internal Zero/Span Module; V Zero/Span Valves; CLO Current Loop Output; TF TFE Sample Particulate Filter; VT Zero/Span Valves and Timer; DO Status Remote Interface. Federal Register: Vol. 41, page 36245, 08/27/1976 and Vol 44, page 33476, 06/11/1979 Monitor Labs/Lear Siegler Model 8850 SO2 Analyzer Automated Equivalent Method: EQSA-0779-039 "Monitor Labs or Lear Siegler Model 8850 Fluorescent SO2 Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with an internal time constant setting of 55 seconds, a TFE sample filter installed on the sample inlet line, with or without any of the following options: 03A Rack; 03B Slides; 05A Valves Zero/Span; 06A IZS Internal Zero/Span Source; 06B,C,D NIST- Traceable Permeation Tubes; 08A Pump; 09A Rack Mount For Option 08A; 010 Status Output W/Connector; 013 Recorder Output Options; 014 DAS Output Options; 017 Low Flow Option; 018 Kicker. Federal Register: Vol. 44, page 44616, 07/30/1979 ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 25 Monitor Labs/Lear Siegler Model 8850S SO2 Analyzer Automated Equivalent Method: EQSA-0390-075 "Monitor Labs or Lear Siegler Model 8850S SO2 Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm. Federal Register: Vol. 55, page 5264, 02/14/1990 Opsis Model AR 500 and System 300 Open Path Ambient Air Monitoring Systems for SO2 Automated Equivalent Method: EQSA-0495-101 "Opsis Model AR 500 System" or "System 300 Open Path (long path) Ambient Air Monitoring Systems," configured for measuring SO2, with one detector and movable grating, operated with a measurement range of 0 to 0.5 ppm or 0 to 1.0 ppm, an installed monitoring path length between 20 and 500 meters (or 20 and 1000 meters with the ER 150 option, AR 500 System only), xenon lamp type B (150 watt), fiber optic cable length between 3 to 20 meters; operating within an ambient air temperature range of -50 to +50°C, an analyzer temperature range of 20 to 30°C, a measurement (integrating) time setting between 30 and 120 seconds (0 min:30 sec. to 2 min:00 sec.), and with a complete cycle time of not more than 200 seconds (3 min, 20 sec.). Under this method designation, the Model AR 500 System or System 300 consists of: AR 500 opto-analyser; emitter EM 110 and receiver RE 110 (together identified as ER 110); optic fibre cable OF60-S; power supply PS 150; Opsis operational software, version 7.0 or 7.1; and initial on-site installation, setup, and limited operator training.2 Optional components that can be used with the Model AR 500 only, in addition to or as alternative to corresponding components listed above: • AR 503 opto-analyzer configured as Model AR 500 (only the center detector active, sequential monitoring) • Emitter/receiver ER 150 (for monitoring path lengths up to 1 kilometer) • Transceiver ER 130 and Retroreflector RE 090 with 7 prisms (max. monitoring path length 150 meters) or 12 prisms (max. monitoring path length 250 meters) • Receiver RE 130 • Xenon lamp type A (higher short-wavelength UV output) • Optic fibre cable OF60-R (low-loss for short wavelengths) • Multiplexers MX 004 and MX 024 • Dataloggers DL 010 and DL 016 • Analogue and digital input/output cards AO 008, AI 016, and DI032 • Analogue and digital isolation cards IA 008, ID 008, OA 008, and OD 008 • Window heaters HF 110 and HF 150 • Mirror heaters HM 110 and HM 150 • Auto calibration unit CU 007 • Software packages IO 80 (for the analogue and digital input/output adapters), DL10 and DL16 (for data loggers), ComVision, and STAT 500; Recommended calibration and accuracy audit components (or equivalent) for either Model AR 500 or System 300: • Wavelength calibration lamp CA 004 • Calibration bench CB 100 • Receiver unit RE 060 (two required) • Calibration unit CA 150, with same type lamp as used in the monitoring path emitter • Power supply PS 150 for calibration unit CA 150 • Calibration cells CC 001-X, where X represents various cell lengths from 1 to 900 mm • Special calibration cells CC 110 or CC 150 (for mounting directly on receiver) • Light meter LM 010. Federal Register: Vol 60, page 21518, 05/02/1995 Philips PW9755 SO2 Analyzer Automated Equivalent Method: EQSA-0676-010 "Philips PW9755 SO2 Analyzer," consisting of the following components: PW9755/02 SO2 Monitor with PW9741/00 SO2 Source, PW9721/00 Filter Set S02, PW9711/00 Electrolyte S02, PW9750/00 Supply Cabinet, PW9750/10 Supply Unit/Coulometric, either PW9731/00 Sampler or PW9731/20 Dust Filter (or vendor-approved alternate particulate filter); operated with a 0-0.5 ppm range and with a reference voltage setting of 760 millivolts; with or without any of the following options: PW9750/30 Frame For MTT; PW9752/00 Air Sampler Manifold; PW9753/00 Mounting Rack For Accessories; PW9750/41 Control Clock 60 Hz; PW9754/00 Air Distributor. Federal Register: Vol. 41, page 26252, 6/25/1976; Vol 41, page 46019,10/19/1976; Vol 42, page 28571, 06/03/1977 Philips PW9700 SO2 Analyzer Automated Equivalent Method: EQSA-0876-011 'Philips PW9700 SO2 Analyzer,' consisting of the following components: PW9710/00 Chemical Unit with PW9711/00, Electrolyte S02, PW9721/00 Filter Set S02, PW9740/00 S02 Source; PW9720/00 Electrical Unit; PW9730/00 Sampler Unit (or vendor-approved alternate particulate filter); operated with a 0-0.5 ppm range and with a reference voltage of 760 millivolts. Federal Register: Vol. 41, page 34105, 08/12/1976 SERES Model SF 2000 G Sulfur Dioxide Analyzer Automated Equivalent Method: EQSA-0810-194 "SERES model SF 2000 G Sulfur Dioxide Analyzer," UV fluorescence method using a wavelength source approaching 215 nm and a selective membrane for aromatic hydrocarbon removal, operated with a full scale measurement range of 0 - 0.5 ppm at any ambient temperature in the range of 20°C to 30°C, with tabletop or rack mounts, microprocessor controlled menu-driven user interface, onboard diagnostics and system test functions, analog output signals of 4-20 mA or user ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 26 selectable voltage ranges up to 10 V, printer port, modem port and 32 pin data/control/alarm port, user selectable manual and automatic zero/span and calibrate modes; with or without a permeation tube system (optional equipment) for internal calibration; operated in accordance with the SF 2000 G User and Maintenance Manual. Federal Register: Vol. 75, page 51039, 08/18/2010 SIR S.A. Model S-5001 U. V. Fluorescence SO2 Analyzer Automated Equivalent Method: EQSA-0507-166 "SIR S.A. Model S-5001 U.V. Fluorescence SO2 Analyzer," operated with a full-scale measurement range of 0 - 0.5 ppm, with an integration time setting of 1 minute, and with or without an optional PCMCIA card or the optional internal permeation oven.2 Federal Register: Vol. 72, page 26627, 05/10/2007 Sutron Model 6020 Sulfur Dioxide Fluorescent Analyzer Automated Reference Method: RFSA-0616-237 "Sutron Model 6020 Sulfur Dioxide Fluorescent Analyzer," operated at any of the following measurement ranges: 0-0.5 ppm, at any ambient temperature in the range of 5-40 °C, at any line voltage in the range of 90-260 VAC, at any sample flow rate in the range of 0.4-0.8 L/min, and in accordance with the Model 6020 SO2 Analyzer Operation Manual, with or without the following options: Zero/span ports for external calibration; an optional inlet filter; or an optional second gas measurement module collocated inside of the enclosure. Federal Register: Vol. 81 page 45284, 07/13/2016 Teledyne Advanced Pollution Instrumentation, Models 100A, 100AS, 100E, 100EU, T100, T100U; Teledyne Analytical Instruments Model 6400A; or Teledyne Monitor Labs sensor-e™ Model TML-50 SO2 Analyzers; or recordum airpointer® system module 801-001000 Automated Equivalent Method: EQSA-0495-100 'Teledyne Advanced Pollution Instrumentation Models 100A, 100AS, 100E, 100EU, T100 or T100U; Teledyne Analytical Instruments Model 6400A; or Teledyne Monitor Labs, Inc. sensor-e™ Model TML-50 UV Fluorescent Sulfur Dioxide Analyzer; operated on any full scale range between 0-50 ppb1 and 0-1000 ppb, at any temperature in the range of 5 to 40 degrees C, with a TFE filter element or a Kynar® DFU installed in the filter assembly, with either the vendor-supplied internal pump or a user- or vender-supplied external vacuum pump capable of maintaining an absolute pressure of 35 cm (14 inches) of mercury (or less) at 1.0 standard liter per minute flow rate, with the following software settings: Dynamic zero: OFF or ON; Dynamic span: OFF; AutoCal: ON or OFF; Dual range: ON or OFF; Autorange: ON or OFF; Temp/pressure compensation: ON; dilution factor: OFF or 1.0; and with or without any of the following options (if available for the various models):2 Rack mount with or without chassis slides; Fluorocarbon zero/span valves; Internal zero/span (IZS); Three-point internal zero/span (IZS, option 51C); 4-20 mA, isolated analog outputs; analog input option; External pump; Status outputs; Control inputs; Rack mount for external pump with tray; RS-232 output; Ethernet output; Zero air scrubber; Combustion Filter; SO2 Permeation tube, certified or uncertified, 0.4 ppm @ 0.7 L/min; SO2 Permeation tube, certified or uncertified, 0.8 ppm @ 0.7 L/min; the NumaView™ software. Airpointer® module 801-001000 only: operated on any full scale range between 0-0.05 ppm and 0- 1.0 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRM/FEM conform mode; at any temperature in the range of 10°C to 45°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without internal span option as module supplement consisting of permeation oven and permeation tube; with or without modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Note 2 applies to the following Teledyne Advanced Pollution Instrumentation Models 100E, 100EU, T100, T100U, and Teledyne Monitor Labs, Inc. Sensor-e™ Model TML-50. Federal Register: Vol 60, page 17061, 04/04/1995 Latest Modification: 08/2010; 05/2013; 07/2014; 9/2015 Teledyne Monitor Labs/Casella/Ecotech Model ML9850/CM2050ZEC9850ZEC9850T; Teledyne Monitor Labs/Casella/ Ecotech/Model ML9850B/CM2050B/EC9850B; or Wedding & Associates Model 1040 SO2 Analyzers Automated Equivalent Method: EQSA-0193-092 "Teledyne Monitor Labs, Casella Monitor, or Ecotech Models ML9850/CM2050/EC9850, orML9850B/CM2050B/EC9850B, Ecotech Model EC9850T, or Wedding & Associates, Inc. Model 1040 Sulfur Dioxide Analyzers," operated on any full scale ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 27 range between 0-0.050 ppm1 and 0-1.0 ppm, at any temperature in the range of 15°C to 35°C, with the service switch on the secondary panel set to the In position; with the following menu choices selected: Range: 0.05 ppm to 1.0ppm; Over-ranging: Enabled or Disabled; Background: Not Disabled; Calibration: Manual or Timed; Diagnostic Mode: Operate; Filter Type: Kalman; Pres/Temp/Flow Comp: On; Span Comp: Disabled; and as follows: Model ML9850/CM2050/ EC9850/EC9850T - with a five-micron Teflon® filter element installed internally, with the 50-pin I/O board installed on the rear panel configured at any of the following output range settings: Voltage, 0.1 V, 1 V, 5 V, 10 V; Current, 0-20 mA, 2-20 mA, 4-20 mA; and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); Rack Mount Assembly; Internal Floppy Disk Drive. Models ML9850B/CM2050B/EC9850B and 1040 - with either a vendor-supplied or equivalent user supplied five-micron Teflon® filter, zero air scrubber, and exhaust pump, and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); Rack Mount Assembly; 50-pin I/O board; Exhaust Scrubber; Internal Zero/Span Assembly (IZS); hinged, fold-down front panel. Operated with the appropriate instrument manual. Federal Register: Vol. 58, page 6964, 02/03/1993 Latest Modification: 03/2011 Thermo Electron Model 43 SO2 Analyzer Automated Equivalent Method: EQSA-0276-009 "Thermo Electron Model 43 Pulsed Fluorescent SO2 Analyzer," equipped with an aromatic hydrocarbon cutter and operated on a range of either 0-0.5 or 0-1.0 ppm, with or without any of the following options: 001 Rack Mounting For Standard 19 Inch Relay Rack; 002 Automatic Actuation Of Zero and Span Solenoid Valves; 003 Type S Flash Lamp Power Supply; 004 Low Flow. Federal Register: Vol. 41, page 8531, 02/27/1976; Vol 41, page 15363, 04/12/1976; Vol 42, page 20490, 04/20/1977 Vol. 44, page 21861, 04/12/1979; Vol. 45, page 2700, 01/14/1980; Vol. 45, page 32419, 05/16/1980 Thermo Environmental Instruments, Inc./Thermo Electron Models 43A, 43B, 43C, 43C-TLE, 43i, 43i-TLE SO2 Analyzers Automated Equivalent Method: EQSA-0486-060 "Thermo Electron or Thermo Environmental Instruments, Inc. Model 43A or 43B Pulsed Fluorescence SO2 Analyzer," operated on the 0-0.1 ppm1, the 0-0.2 ppm1, the 0-0.5 ppm, or the 0-1.0 ppm range, with either a high or a low time constant setting (Model 43 A) and with or without any of the following options:2 001 Teflon Particulate Filter 004 High Flow Rate (1 Lpm) 007Remote Activation of Zero/Span Valves 002 19" Rack Mounting Configuration 005 Current Output 008 RS-232 Interface (Model 43B) 003 Internal Zero/Span Valves 006 Internal Permeation 009 Pressure/Temperature Compensation Span Source (Model 43B) "Thermo Environmental Instruments, Inc. Models 43C, 43C-TLE, 43/, 43i-TLE, Pulsed Fluorescence SO2 Analyzer," operated on any measurement range between 0-50 ppb1 (0-101 ppb for Model TLE) and 0-1000 ppb, with any time average setting from 10 to 300 seconds, with temperature and/or pressure compensation on or off, operated at temperatures between 20°C and 30°C, and with or without any of the following options:2 Teflon particulate filter, 4-20 mA current output or I/O expansion board, Rack mounts, Internal permeation span source/Permeation oven, Internal zero/span and sample solenoid valves, High flow rate (0.5-1.0 Lpm); Models 43C, 43C-TLE: Remote activation of zero/span and sample valves, RS-232/485 interface, airpointer® Model 801-001000-T, operated on any full scale range between 0-0.05 ppm and 0-1.0 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRM/FEM conform mode; at any internal temperature in the range of 15°C to 39°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without internal span option as module supplement consisting of permeation oven and permeation tube; with or without modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Federal Register: Vol. 51, page 12390, 04/10/1986 Latest Modification: 10/2015 ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 28 Ozone 2B Technologies Model 202 and 205 Ozone Monitors Automated Equivalent Method: EQOA-0410-190 "2B Technologies Models 202 (single beam) and 205 (dual beam) Ozone Monitors," operated in a range of 0 - 0.5 ppm in an environment of 10 - 40°C, with temperature and pressure compensation, internal DewLine for humidity control, using a 10 second average, with a 110-220V AC power adapter or a 12 V DC source 4.0 to 6.0 watt power consumption, operated according to the Model 202 or 205 Ozone Monitor Operation Manual with or without the following: cigarette lighter adapter or a 12V DC battery for portable operation, external TFE inlet filter and holder, serial data port with computer cable, BNC connector for 0-2.5 V scalable analog output, internal data logger, 3-analog inputs for external signals (such as temperature, relative humidity or pressure), rack mount hardware, on-board backup sample pump. Federal Register: VoL75, pages 22126-22127, 04/27/2010 Latest Modification: 12/2010 2B Technologies Model 211 Ozone Monitor Automated Equivalent Method: EQOA-0514-215 "2B Technologies Models 211 Scrubberless Ozone Monitors," operated in a range of 0 - 0.5 ppm in an environment of 20 - 30°C, with temperature and pressure compensation, internal DewLine for humidity control, gas phase titration of ozone for interference-free measurements, using a 1 minute average, with a 110-220V AC power adapter or a 12V DC source, 8.0 to 12.0 watt power consumption, operated according to the Model 211 Scrubberless Ozone Monitor Operation Manual with either an external nitric oxide source or internal photolytic generator for production of NO scrubber gas from nitrous oxide, and with or without the following: cigarette lighter adapter or a 12V DC battery for portable operation, external PTFE inlet filter and holder, serial data port with computer cable, BNC connector for 0-2.5 V or 4-20 mA scalable analog output, internal data logger, microFlash card for data recording and backup, rack mount hardware, and long life sample pump. Federal Register: Vol.79, pages 34734-34735 06/18/2014 2B Technologies Model 106-L or 106-OEM-L Ozone Monitor Automated Equivalent Method: EQOA-0914-218 "2B Technologies Model 106-L or 106-OEM-L Ozone Monitor," operated in a range of 0 - 0.5 ppm in an environment of 20- 30 °C, temperature and pressure compensation, internal dewLine for humidity control, using a 1 minute average, with a 12V DC source supplied by a 100-240V AC power adapter, operated according to the Model 106-L Ozone Monitor Operation Manual and with or without the following: cigarette lighter adapter or a 12V DC battery for portable operation, external PTFE or PVDF inlet filter and holder, USB data port with computer cable. Federal Register: Vol. 79, page 65392,11/04/2014 2B Technologies Model Personal Ozone Monitor (POM) Automated Equivalent Method: EQOA-0815-227 "2B Technologies Model Personal Ozone Monitor (POM)," operated in a range of 0 - 0.5 ppm in an environment of 20-30 °C, temperature and pressure compensation, using a 10 second averaging time, with a 12V DC source supplied by a 100-240V AC power adapter, operated according to the POM Operation Manual and with or without the following: cigarette lighter adapter or a 12V DC battery or a 7-24 V battery for portable operation, USB data port with computer cable. Federal Register: Vol. 80, page 51802, 8/26/2015 Beckman Model 950A Ozone Analyzer Automated Reference Method: RFOA-0577-020 "Beckman Model 950A Ozone Analyzer," operated on a range of 0-0.5 ppm and with the "SLOW" (60 second) response time, with or without any of the following options: Internal Ozone Generator; Computer Adaptor Kit; Pure Ethylene Accessory. Federal Register: Vol. 42, page 28571, 06/03/1977 Bendix or Combustion Engineering Model 8002 Ozone Analyzer Automated Reference Method: RFOA-0176-007 "Bendix or Combustion Engineering Model 8002 Ozone Analyzer," operated on the 0-0.5 ppm range, with a 40 second time constant, with or without any of the following options: Rack Mounting with Chassis Slides; Rack Mounting without Chassis ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 29 Slides; Zero and Span Timer; Ethylene/CCh Blend Reactant Gas. Federal Register: Vol. 41, page 5145, 02/04/1976 and Vol 45, page 18474, 03/21/1980 Columbia Scientific Industries Model 2000 Ozone Meter Automated Reference Method: RFOA-0279-036 "Columbia Scientific Industries Model 2000 Ozone Meter," when operated on the 0-0.5 ppm range with either AC or battery power: The BCA 952 battery charger/AC adapter M952-0002 (115V) or M952-0003 (230V) is required for AC operation; an internal battery M952-0006 or 12 volt external battery is required for portable non-AC powered operation. Federal Register: Vol. 44, page 10429, 02/20/1979 Dasibi Models 1003-AH, 1003-PC, or 1003-RS Ozone Analyzers Automated Equivalent Method: EQOA-0577-019 "Dasibi Model 1003-AH, 1003-PC, or 1003-RS Ozone Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with or without any of the following options: Adjustable Alarm; Aluminum Coated Absorption Tubes, Integrated Output; Vycor- Jacketed U.V. Source Lamp; BCD Digital Output; Rack Mounting Ears and Slides; 0-10 mV, 0-100 mV, 0-1 V, Or 0-10 V; Glass (Pyrex) Absorption Tubes; Teflon-based Solenoid Valve; Analog Output. Federal Register: Vol. 42, page 28571, 06/03/1977 Dasibi Models 1008-AH, 1008-PC, or 1008-RS Ozone Analyzers Automated Equivalent Method: EQOA-0383-056 "Dasibi Model 1008-AH, 1008-PC, or 1008-RS Ozone Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with or without any of the following options: Aluminum Coated Absorption Tubes; BCD Digital Output; RS232 Interface; Glass (Pyrex) Absorption Tubes; Vycor-Jacketed U.V. Source Lamp; Ozone Generator; Teflon-based Solenoid Valve; Photometer Flow Restrictor (2 Lpm); 4- 20 mA, Isolated, or Dual Analog Outputs; Rack Mounting Brackets or Slides; 20 Second Update Software. Federal Register: Vol 48, page 10126, 03/10/1983 DKK-TOA Corp. Model GUX-113E Ozone Analyzer Automated Equivalent Method: EQOA-0200-134 "DKK-TOA Corporation Models GUX-113E and GUX-113E-1 Ozone Analyzer," operated at any temperature in the range of 15°C to 35°C, on any of the following measurement ranges: 0-0.100 ppm1, 0-0.200 ppm1, 0-0.5 ppm, or 0-1.000 ppm, and with or without the optional Internal Ozone Generator.2 Federal Register: Vol. 65, page 11308, 03/02/2000 DKK-TOA Corp. Model GUX-313E Ambient O3 Analyzer Automated Equivalent Method: EQOA-1107-169 "DKK-TOA Corporation Model GUX-313E Ambient O3 Analyzer," operated at any environmental temperature in the range of 20°C to 30°C on any of the following measurement ranges1: 0-0.1 ppm, 0-0.2 ppm and 0-0.5 ppm.2 Federal Register: Vol. 72, page 63176,11/08/2007 Ecotech Serinus 10 Ozone Analyzer or OpsisAB OPS 10 Ozone Analyzer or Tisch Environmental TE 1.0 Ozone Analyzer Automated Equivalent Method: EQOA-0809-187 "Ecotech Serinus 10 Ozone Analyzer" or "Opsis AB OPS 10 Ozone Analyzer" or "Tisch Environmental TE 1.0 Ozone Analyzer," operated in the range of 0-0.5 ppm, with a five-micron Teflon® filter element installed, and with the following selected: Control Loop-Enabled, Diagnostic Mode-Operate, Pres/Temp/Flow Compensation-Enabled, Span Compensation- Disabled, with concentration automatically corrected for temperature and pressure changes, and operated according to the Serinus 10 Ozone Analyzer User Manual, or the Opsis AB OPS 10 Ozone Analyzer User Manual, or the Tisch Environmental TE 1.0 Ozone Analyzer Instruction Manual, as appropriate. Federal Register: Vol. 74, page 38184, 07/31/2009 Latest Modifications: 05/2010, 05/2012, 8/2014 Environics Series 300 Ozone Analyzer Automated Equivalent Method: EQOA-0990-078 "Environics Series 300 Computerized Ozone Analyzer," operated on the 0-0.5 ppm range, with the following parameters entered into the analyzer's computer system: Absorption Coefficient = 308 V4; Flush Time = 3; Integration Factor = I: Offset ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 30 Adjustment = 0.025ppm; Ozone Average Time = 4; Signal Average = 0; Temp/Press Correction = On; and with or without the RS-232 Serial Data Interface. Federal Register: Vol. 55, page 38386, 09/18/1990 Environnement S.A. Model Os41M UV Ozone Analyzer Automated Equivalent Method: EQOA-0895-105 "Environnement S.A. Model CMIM UV Photometric Ozone Analyzer," operated on a full scale range of 0 - 500 ppb, at any temperature in the range of 15°C to 35°C, with the response time set to 50 seconds, and with or without any of the following options:2 Internal Ozone Generator; Span External Control; RS232-422 Serial Interface; Internal Printer. Federal Register: Vol 60, page 39382, 08/02/1995 Environnement S.A. Model ()t-/2M UV Ozone Analyzer Automated Equivalent Method: EQOA-0206-148 "Environnement S.A Model 0;,42IVI UV Photometric Ozone Analyzer," operated with a full scale range of 0 - 500 ppb, at any temperature in the range of 10°C to 35°C, with a 5-micron PTFE sample particulate filter, with response time setting of 11 (Automatic response time), and with or without any of the following options:2 a) Internal ozone generator, b) Span external control (zero/span solenoid valve). Federal Register: VoL67, page 42557, 06/24/2002 Environnement S.A. SANOA Multigas Longpath Monitoring System Automated Equivalent Method: EQOA-0400-137 "Environnement S.A. Model SANOA Multigas Longpath Air Quality Monitoring System, consisting of a receiver, one or more projectors, interface unit, a user-provided control unit computer running the SANOA VisionAIR software, and associated incidental equipment; configured for measuring O3, with the temperature control and internal calibration cell options installed, operated with a measurement range of 0 to 0.5 ppm, over an installed monitoring path length of between 27 and 500 meters, within an ambient air temperature range of -30 to +45°C, with a measurement (integrating) time of 180 seconds, and with or without external temperature and barometric pressure sensors or any of the following options: external (meteo) input connection, series 1M bus connection, OGR type projector, analog outputs. A high-concentration ozone generator, part # 80- 231-03, or the SONIMIX 7121B calibration system is recommended for calibration or accuracy auditing. Federal Register: Vol.65, page 26603, 05/08/2000 Environnement S.A. Model 03 42e UV Ozone Analyzer Automated Equivalent Method: EQOA-0515-225 "Environnement S.A. Model 03 42e UV Photometric Ozone Analyzer," operated in a range of 0-0.5 ppm in an environment of 0-35 °C, with a Teflon sample inlet filter, with automatic temperature and pressure compensation, with a flow-rate of 1 Lpm and with zero/span external solenoid valve. Federal Register: Vol. 80, page 32114, 6/05/2015 Horiba Instruments Models APOA-360 or APOA-360-CE Ozone Monitor Automated Equivalent Method: EQOA-0196-112 "Horiba Instruments, Inc. Model APOA-360 or APOA-360-CE Ambient Ozone Monitor," operated with a full scale range of 0-0.50 ppm, at any temperature in the range of 10°C to 40°C, with a Line Setting of "MEASURE," and an Analog Output of "MOMENTARY VALUE," and with or without any of the following options:21) Rack Mounting Plate and Side Rails 2) RS- 232 Communications Port, and 3) Optional Internal Zero/Span Check Federal Register: Vol 61, page 11404, 03/20/1996 ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 31 Horiba Instruments Model APOA-3 70 Ozone Monitor Automated Equivalent Method: EQOA-0506-160 "Horiba Instalments Incorporated APOA-370 Ambient O3 Monitor," standard specification, operated with a full-scale fixed measurement range of 0 - 0.5 ppm, with the automatic range switching off, at any temperature in the range of 20 to 30°C.2 Federal Register: Vol 71, page 25587, 05/01/2006 McMillan (MEC) Models 1100-1,1100-2, and 1100-3 Ozone Meters "MEC Model 1100-1 Ozone Meter," Automated Reference Method: RFOA-1076-014 "MEC Model 1100-2 Ozone Meter," Automated Reference Method: RFOA-1076-015 "MEC Model 1100-3 Ozone Meter,' Automated Reference Method: RFOA-1076-016 Operated on a 0-0.5 ppm range, with or without any of the following options: 0011 Rack Mounting Ears; 0026 Alarm Set Feature; 0012 Instrument Bail; 0033 Local-Remote Sample; Zero, Span Kit Blend Feature; 0016 Chassis Slide Kit; 0040 Ethylene/CCh. Federal Register: Vol. 41, page 46647,10/22/1976; Vol 42, page 30235, 06/13/1977 Meloy Model OA325-2R Ozone Analyzer Automated Reference Method: RFOA-1075-003 "Meloy Model OA325-2R Ozone Analyzer," operated with a scale range of 0-0.5 ppm, with or without any of the following options: 0-4 Output Booster Amplifier; 0-18 Rack Mount Conversion; 0-18A Rack Mount Conversion. Federal Register: Vol. 40, page 54856,11/26/1975 Meloy Model OA350-2R Ozone Analyzer Automated Reference Method: RFOA-1075-004 "Meloy Model OA350-2R Ozone Analyzer," operated with a scale range of 0-0.5 ppm, with or without any of the following options: 0-2 Automatic Zero and Span; 0-3 Remote Control Zero and Span; 0-4 Output Booster Amplifier; 0-18 Rack Mount Conversion; 0-18A Rack Mount Conversion. Federal Register: Vol. 40, page 54856,11/26/1975 Monitor Labs Model 8410E Ozone Analyzer Automated Reference Method: RFOA-1176-017 "Monitor Labs Model 8410E Ozone Analyzer," operated on a range of 0-0.5 ppm with a time constant setting of 5 seconds, with or without any of the following options: DO Status Outputs; ER Ethylene Regulator Assembly; V TFE Zero/Span Valves; TF TFE Sample Particulate Filter; VT TFE Zero/Span Valves and Timer. Federal Register: Vol. 41, page 53684,12/08/1976 Monitor Labs/Lear Siegler Model 8810 Ozone Analyzer Automated Equivalent Method: EQOA-0881-053 "Monitor Labs or Lear Siegler Model 8810 Photometric Ozone Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with selectable electronic time constant settings from 20 through 150 seconds, with or without any of the following options: 05 Pressure Compensation; 06 Averaging Option; 07 Zero/Span Valves; 08 Internal Zero/Span (Valve and Ozone Source); 09 Status; 10 Particulate Filter; 15 through 20 DAS/REC Output. Federal Register: Vol. 46, page 52224,10/26/1981 Opsis Model AR 500 and System 300 Open Path Ambient Air Monitoring Systems for Ozone Automated Equivalent Method: EQOA-0495-103 "Opsis Model AR 500 System" or "System 300 Open Path (long path) Ambient Air Monitoring Systems," configured for measuring O3, with one detector and moveable grating, operated with a measurement range of 0 to 0.5 ppm, an installed monitoring path length between 20 and 500 meters (or 20 and 1000 meters with the ER 150 option, AR 500 System only), xenon lamp type B (150 watt), fiber optic cable length between 3 to 20 meters; operating within an ambient air temperature range of -50 to +50°C, an analyzer temperature range of 20 to 30°C, a measurement (integrating) time setting between 30 and 120 seconds (0 min:30 sec. to 2 min:00 sec.), and with a complete cycle time of not more than 200 seconds (3 min, 20 sec.). Under this method designation, the Model AR 500 System or System 300 consists of: AR 500 opto-analyser; emitter EM 110 and receiver RE 110 (together identified as ER 110); optic fibre cable OF60-S; power supply PS 150, Opsis operational software, version 7.0 or 7.1; and initial on-site installation, setup, and limited operator training.2 ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 32 Optional components that can be used with the Model AR 500 only, in addition to or as alternative to corresponding components listed above: • AR 503 opto-analyzer configured as Model AR 500 (only the center detector active, sequential monitoring) • Emitter/receiver ER 150 (for monitoring path lengths up tol kilometer) • Transceiver ER 130 and Retroreflector RE 090 with 7 prisms (max. monitoring path length 150 meters) or 12 prisms (max. monitoring path length 250 meters) • Receiver RE 130 • Optic fibre cable OF60-R (low-loss for short wavelengths) • Multiplexers MX 004 and MX 024 • Dataloggers DL 010 and DL 016 • Analogue and digital input/output cards AO 008, AI016, and DI032 • Analogue and digital isolation cards IA 008, ID 008, OA 008, and OD 008 • Window heaters HF 110 and HF 150 • Mirror heaters HM 110 and HM 150 • Auto calibration unit CU 007 • Software packages IO 80 (for the analogue and digital input/output adapters), DL10 and DL16 (for data loggers), ComVision, and STAT 500; Recommended calibration and accuracy audit components (or equivalent) for either Model AR 500 or System 300: • Wavelength calibration lamp CA 004 • Calibration bench CB 100 • Receiver unit RE 060 (two required) • Calibration unit CA 150, with same type lamp as used in the monitoring path emitter • Power supply PS 150 for calibration unit CA 150 • Calibration cells CC 001-X, where X represents various cell lengths from 1 to 900 mm • Special calibration cells CC 110 or CC 150 (for mounting directly on receiver) • Ozone generator OC 500 • Light meter LM 010. Federal Register: Vol 60, page 21518, 05/02/1995 PCI Ozone Corporation Model LC-12 Ozone Analyzer Automated Equivalent Method: EQOA-0382-055 "PCI Ozone Corporation Model LC-12 Ozone Analyzer," operated on a range of 0-0.5 ppm. Federal Register: Vol. 47, page 13572, 03/31/1982 Philips PW9771 03 Analyzer Automated Equivalent Method: EQOA-0777-023 "Philips PW9771 03 Analyzer," consisting of the following components: PW9771/00 03 Monitor with PW9724/00 Disc.-Set; PW9750/00 Supply Cabinet; PW9750/20 Supply Unit operated on a range of 0-0.5 ppm, with or without any of the following accessories: PW9732/00 Sampler Line Heater; PW9750/30 Frame For MTT; PW9750/41 Control Clock 60 Hz; PW9733/00 Sampler; PW9752/00 Air Sampler Manifold. Federal Register: Vol. 42, page 38931, 08/01/1977; Vol 42, page 57156,11/01/1977 Seres Model OZ 2000 G Ozone Analyzer Automated Equivalent Method: EQOA-0506-161 "Seres OZ 2000 G Ozone Ambient Air Analyzer," operated with a full scale range of 0 - 0.5 ppm, at any temperature in the range of 20°C to 30°C, and with or without either of the following options: internal ozone generator, teletransmission interface.2 Federal Register: Vol 71, page 25587, 05/01/2006 SIR S.A. Model S-5014 O3 Analyzer Automated Equivalent Method: EQOA-0207-164 "SIR S.A. Model S-5014 Photometric O3 Analyzer," operated on the 0 - 500 ppb measurement range, within an ambient temperature range of 20°C to 30°C, with a sample inlet particulate filter, and with or without an optional PCMCIA card. Federal Register: Vol 72, page 8985, 02/28/2007 Sutron Corporation Model 6030 O3 Analyzer Automated Equivalent Method: EQOA-0415-222 "Sutron Model 6030 Ozone Analyzer," operated at any of the following measurement ranges: 0-0.05 ppm, 0-0.5 ppm and 0- 1.0 ppm, at any ambient temperature in the range of 5°C -45 °C, with an averaging time of 1 to 99 analyzer cycles (0 to 396 seconds), with sample flow rate of 0.5 to 1 Lpm and in accordance with the Model 6030 Ozone Analyzer Operation Manual and with or without the following options: internal ozone generator, zero/span ports for external calibration. Federal Register: Vol. 80, page 32114, 6/05/2015 ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 33 Tanabyte Models 722, 723, 724, 725, or 726 Ambient Ozone Analyzer Automated Equivalent Method: EQOA-0407-165 "Tanabyte Models 722,723, 724, 725, or 726 Ambient Ozone Analyzer," enclosed in either a Dual-Bay Chassis or a Single- Bay Chassis and operated on either the 0 - 0.5 ppm or 0 -1.0 ppm measurement range, within an ambient temperature range of 20 to 30 degrees C, and with a sample inlet particulate filter installed in the sample filter holder. Federal Register: Vol 72, page 20846, 04/26/2007 Teledyne Advanced Pollution Instrumentation, Model 400E or T400; Advanced Pollution Instrumentation, Model 400/400A; Teledyne Monitor Labs sensor-e™ Model TML-10 Ozone Analyzers; or recordum airpointer® system module 801-004000; Automated Equivalent Method: EQOA-0992-087 "Teledyne Advanced Pollution Instrumentation. Model 400E or T400; Advanced Pollution Instrumentation, Model 400 or 400A; or Teledyne Monitor Labs sensor-e™ Model TML-10 Ozone Analyzef' operated on any lull scale range between 0-100 ppb1 and 0-1000 ppb, with any range mode (Single, Dual, or AutoRange), at any ambient temperature in the range of 5°C to 40°C, and with a TFE filter or a Kynar® DFU. Models 400E, T400 and TIV1L-10: operated with a sample flow rate of 800 ± 80 cm3/min (sea level), with the dilution factor set to 1, with Dynamic Zero ON or OFF, with Dynamic Span OFF, with Temp/Press compensation ON, and with or without any of the following options: Internal or external sample pump, Sample/Cal valve option, Internal Zero/Span (IZS), Rack mount with or without slides, analog input option, 4-20 mA isolated current loop output; the NumaView™ software.2 Models 400/400A: operated with the dynamic zero and span adjustment feature (some Model 400 units only) set to OFF, and with or without any of the following options: Zero/Span Valve option, Internal Zero/Span (IZS) option, IZS ozone generator reference feedback option, standard serial port or Multi-drop RS-232, digital status outputs, analog outputs: 100 mV, IV, 5V, 10V, 4-20 mA current loop, optional metal wool ozone scrubber, optional external sample pump, optional 47 mm diameter filter, optical bench heater, rack mount with slides; the NumaView™ software, airpointer® system module 801-004000 only: operated on any full scale range between 0-0.100 ppm and 0- 1.0 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRMZFEM conform mode; at any temperature in the range of 10°C to 45°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without the internal span option as module supplement consisting of ozone generator; with or without modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Note 2 applies to the following Teledyne Advanced Pollution Instrumentation, Models 400E, T400, and Teledyne Monitor Labs, Inc. Sensor-e™ Model TML-10. Federal Register: Vol. 57, page 44565, 09/28/1992; Vol 63, page 31992, 06/11/1998 Vol 67, page 57811, 09/12/2002 Latest Modification: 08/2010; 05/2013; 07/2014; 9/2015 Teledyne Advanced Pollution Instrumentation Model 265E or T265 Chemiluminescence Ozone Analyzers Automated Equivalent Method: EQOA-0611-199 or Automated Reference Method: RFOA-0216-230 "Teledyne Advanced Pollution Instrumentation, Model 265E or T265 Chemiluminescence Ozone Analyzer," operated on any full scale range between 0-100 ppb and 0-1000 ppb, with any range mode (Single, Dual, or AutoRange), at any operating temperature in the range of 5°C to 40°C, and with a TFE filter or a Kynar® DFU in the sample air inlet, operated with a sample flow rate of 500 ± 50 cm3/min (sea level), with the dilution factor set to 1, with Temp/Press compensation ON, and in accordance with the appropriate associated instrument manual, and with or without any of the following options: Internal or external sample pump, Sample/Cal valve option, Rack mount with or without slides, analog input option, 4-20 mA isolated current loop output. Note 2 applies to the following Teledyne Advanced Pollution Instrumentation Models 265E and T265. Federal Register: Vol. 76, page 62402,10/07/2011; Vol 81 page 25397, 04/28/2016 Latest Modification: 10/2012; 07/2014 Teledyne Advanced Pollution Instrumentation, Model T204 Analyzer Automated Equivalent Method: EQOA-0514-214 "Teledyne Advanced Pollution Instrumentation, Model T204 NOX + 03 Analyzer", operated on any full scale range between 0-100 ppb and 0-500 ppb, at any operating temperature from 5°C to 40°C, with either a user-or vendor-supplied vacuum pump capable of providing an absolute pressure of 10 inches mercury or less at 3 sLpm, in accordance with the associated instrument manual, and with or without any of the following options: Zero/Span valves, external communication and data monitoring interfaces. Note 2 applies to the Teledyne Advanced Pollution Instrumentation, Model T204. Federal Register: Vol.79, pages 34734-34735, 06/18/2014 Latest Modification: 07/2014 ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 34 Teledyne Advanced Pollution Instrumentation, Model 430 Ozone Analyzer Automated Equivalent Method: EQOA-1015-229 "Teledyne Advanced Pollution Instrumentation, Model 430 Ozone Analyzer", operated with a full scale range between 0-500 ppb, at any operating temperature from 5°C to 40°C, with a sample particulate filter, with a 100-240V AC to DC power adapter or a 12V DC source capable of providing 9 watts of power, in accordance with the associated instrument manual, and with or without any of the following options: internal long-life pump, external long-life pump, external portable battery pack, external communication and data monitoring interfaces. Federal Register: Vol. 80, pages 72432,11/19/2015 Teledyne Monitor Labs/Casella/Ecotech Models ML9810/CM2010/EC9810, -11, or -12, Teledyne Monitor Labs/Casella/Ecotech Model ML9810B/CM2010B/EC9810B, or Wedding & Associates Model 1010 Ozone Analyzers Automated Equivalent Method: EQOA-0193-091 "Teledyne Monitor Labs, Casella Monitor, or Ecotech Models ML9810/CM2010/EC9810, ML9811/CM2011/EC9811, ML9812/CM2012/EC9812, orML9810B/CM2010B/EC9810B or Wedding & Associates, Inc. Model 1010 Ozone Analyzers," operated on any full scale range between 0-0.05 ppm1 and 0-1.0 ppm, at any temperature in the range of 15°C to 35°C, with the service switch on the secondary panel set to the In position; with the following menu choices selected: Range: 0.05ppm to 1.0ppm; Over-ranging: Enabled ox Disabled, Calibration: Manual or Timed, Diagnostic Mode: Operate; Filter Type: Kalman; Pres/Temp/Flow Comp: On', Span Comp: Disabled, and as follows: Models ML9810/CM2010/EC9810, -11, and -12 - with a five-micron Teflon® filter element installed internally, with the 50-pin I/O board installed on the rear panel configured at any of the following output range settings: Voltage, 0. IV, IV, 5 V, 10V; Current, 0-20 mA, 2-20 mA, 4-20 mA; and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); Rack Mount Assembly; Internal Floppy Disk Drive. Models ML9810B/CM2010B/EC9810B and 1010 - with either a vendor-supplied or equivalent user-supplied five micron Teflon® filter and exhaust pump, and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); Rack Mount Assembly; 50-pin I/O board; Internal Zero/Span Assembly (IZS); hinged, fold-down front panel. Operated with appropriate instrument manual. Federal Register: Vol. 58, page 6964, 02/03/1993 Latest Modification: 03/2011 Thermo Electron/Thermo Environmental Instruments Models 49, 49C, 49i Automated Equivalent Method: EQOA-0880-047 "Thermo Electron or Thermo Environmental Instruments, Inc. Model 49 U. V. Photometric Ambient O3 Analyzer," operated on a measurement range of either 0-0.5 or 0-1.0 ppm with or without any of the following options: 49-001 Teflon Particulate Filter; 49-002 19 Inch Rack Mount; 49-100 Internal Ozone Generator for Zero, Precision, and Level 1 Span Check; 49-103 Internal Ozone Generator for Zero, Precision, and Level 1 Span Checks With Remote Activation; 49-488 GPIB (General Purpose Interface Bus) IEEE-488. Model 49C or 49i U.V. Photometric Ambient O3 Analyzer," operated on any measurement range between 0- 0.051 to 1.0 ppm, with any time average setting between 10 and 300 seconds, with the temperature and/or pressure compensation on or off, within a temperature range of 20°C to 30°C, with or without any of the following options: 2 Teflon particulate filter, Internal Zero Air Scrubber, Internal Ozonator with remote activation, Rack mounts; Model 49C: Internal Ozonator, Carrying Handle, 4-20 mA current output, RS-232 Interface, RS-485 Interface; Model 49i: I/O expansion board, airpointer® Model 801- 004000-T, operated on any full scale range between 0-0.100 ppm and 0-1.0 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRM/FEM conform mode; at any internal temperature in the range of 10°C to 44°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without the internal span option as module supplement consisting of ozone generator; with or without modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Federal Register: Vol. 45, page 57168, 08/27/1980 Latest Modification: 12/2011; 10/2015 ------- CO List of Designated Reference and Equivalent Methods. December 17.2016 Page 35 Carbon Monoxide Beckman Model 866 CO Monitoring System Automated Reference Method: RFCA-0876-012 "Beckman Model 866 Ambient CO Monitoring System," consisting of the following components: Pump/Sample-Handling Module; Gas Control Panel; Model 865-17 Analyzer Unit; Automatic Zero/Span Standardize^ operated with a 0-50 ppm range, a 13 second electronic response time, with or without any of the following options: Current Output Feature; Bench Mounting Kit; Linearizer Circuit. Federal Register: Vol. 41, page 36245, 08/27/1976 Bendix/Combustion Engineering Model 8501-5CA CO Analyzer Automated Reference Method: RFCA-0276-008 "Bendix or Combustion Engineering Model 8501-5CA Infrared CO Analyzer," operated on the 0-50 ppm range and with a time constant setting between 5 and 16 seconds, with or without any of the following options: Rack Mounting with Chassis Slides; Rack Mounting without Chassis Slides; External Sample Pump. Federal Register: Vol. 41, page 7450, 02/18/1976 Dasibi Model 3003 CO Analyzer Automated Reference Method: RFCA-0381-051 "Dasibi Model 3003 Gas Filter Correlation Dasibi Environmental CO Analyzer," operated on the 0-50 sample particulate filter installed on the sample inlet line, with or without any of the following options: 3-001 Rack Mount 3-003 BCD Digital Output 3-007 Zero/Span Module 3-002 Remote Zero and Span 3-004 4-20 Milliamp Output Federal Register: Vol. 46, page 20773, 04/07/1981 Dasibi Model 3008 CO Analyzer Automated Reference Method: RFCA-0488-067 "Dasibi Model 3008 Gas Filter Correlation CO Analyzer," operated on the 0-50 ppm range, with a time constant setting of 60 seconds, a particulate filter installed in the analyzer sample inlet line, with or without use of the auto zero or auto zero/span feature, and with or without any of the following options: N-0056-A RS-232-C Interface; S-0132-A Rack Mounting Slides; Z- 0176-S Rack Mounting Brackets. Federal Register: Vol. 53, page 12073, 04/12/1988 DKK-TOA Corporation Model GFC-311E Ambient CO Analyzer Automated Reference Method: RFCA-0907-167 "DKK-TOA Corporation Model GFC-31 IE Ambient CO Analyzer," operated with full scale fixed measurement ranges of 0- 5, 0-20, and 0-50 ppm at any environmental temperature in the range of 20°C to 30°C. Federal Register: Vol. 72, page 56339,10/03/2007 Ecotech Serinus 30 Carbon Monoxide Analyzer or Opsis AB OPS 30 Carbon Monoxide Analyzer or Teledyne Analytical Instruments GFC7001E Carbon Monoxide Analyzer or Tisch Environmental TE 3.0 Carbon Monoxide Analyzer Automated Reference Method: RFCA-0509-174 "Ecotech Serinus 30 Carbon Monoxide Analyzer" or "Opsis AB OPS30 Carbon Monoxide Analyzer" or "Teledyne Analytical Instruments GFC7001E Carbon Monoxide Analyzer" or "Tisch Environmental TE 3.0 Carbon Monoxide Analyzer," operated in the range of 0-50 ppm, with a five-micron Teflon® filter element installed, and with the following selected: Background- Enabled, Control Loop-Enabled, Diagnostic Mode-Operate, Pres/Temp/Flow Compensation-Enabled, Span Compensation- Disabled, with concentration automatically corrected for temperature and pressure changes, and operated according to the Serinus 30 Carbon Monoxide Analyzer User Manual or the OPS 30 Carbon Monoxide Analyzer User Manual or the Teledyne Analytical Instruments GFC700 IE Carbon Monoxide Analyzer Instruction Manual, or the Tisch Environmental TE 3.0 Carbon Monoxide Analyzer Instruction Manual as appropriate. Federal Register: Vol. 74, page 26395, 06/02/2009 Latest Modifications: 05/2010, 05/2011, 05/2012, 08/2014 ppm range, with a Panel ------- CO List of Designated Reference and Equivalent Methods. December 17.2016 Page 36 Environnement S.A. Model COllM CO Analyzer Automated Reference Method: RFCA-0995-108 "Environnement S. A. Model COl 1M Ambient Carbon Monoxide Analyzer," operated on a Ml scale range of 0 - 50 ppm, at any temperature in the range of 15°C to 35°C, with a 5-micron PTFE sample particulate filter, with the following software settings: Automatic response time ON; Minimum response time set to 40 seconds (RT 13); Automatic ZERO-REF cycle programmed every 24 hours; and with or without any of the following options:2 RS232-422 Serial Interface; Internal Printer. Federal Register: Vol 60, page 54684,10/25/1995 Environnement S.A. Model C012M CO Analyzer Automated Reference Method: RFCA-0206-147 "Environnement S. A Model C012M Gas Filter Correlation Carbon Monoxide Analyzer," operated with a full scale range of 0 - 50 ppm, at any temperature in the range of 10°C to 35°C, with a 5-micron PTFE sample particulate filter, with response time ON, and with the automatic "ZERO-REF" cycle either ON or OFF.2 Federal Register: Vol 67, page 42557, 06/24/2002 Environnement S.A. Model C012e CO Analyzer Automated Reference Method: RFCA-0915-228 "Environnement S.A. Model C012e Carbon Monoxide Analyzer", an infrared absorption spectroscopy technique operated on a full scale range of 0 - 50 ppm, at any temperature in the range of 10°C to 35°C, with a teflon sample particulate filter with the following software settings: Automatic response time ON; Automatic "ZERO-REF" cycle either ON or OFF and with or without the following options: ESTEL Analog Input/Output Board, LCD color touch screen and Carbon Dioxide CO2 sensor. Federal Register: Vol 80, page 72432,11/19/2015 Horiba Models AQM-10, AQM-11, or AOM12 CO Monitoring Systems Automated Reference Method: RFCA-1278-033 "Horiba Models AQM-10, AQM-11, or AQM12 Ambient CO Monitoring Systems," operated on the 0-50 ppm range, with a response time setting of 15.5 seconds, with or without any of the following options: AIC-101 Automatic Indication Corrector; VIT-3 Non-Isolated Current Output; ISO-2 and DCS-3 Isolated Current Output. Federal Register: Vol. 43, page 58429,12/14/1978 Horiba Model APMA-300E CO Monitoring System Automated Reference Method: RFCA-1180-048 "Horiba Model APMA-300E Ambient Carbon Monoxide Monitoring System," operated on the 0-20 ppm1, the 0-50 ppm, or the 0-100 ppm range with a time constant switch setting of No. 5. The monitoring system may be operated at temperatures between 10°C and 40°C. (This method was originally designated as "Horiba Model APMA 300E/300SE Ambient Carbon Monoxide Monitoring System.") Federal Register: Vol. 45, page 72774,11/03/1980 Horiba Models APMA-360 or APMA-360-CE CO Monitor Automated Reference Method: RFCA-0895-106 "Horiba Instruments Incorporated, Models APMA-360 or APMA-360-CE Ambient Carbon Monoxide Monitor," operated on the 0-50 ppm range, with the Line Setting set to "MEASURE," with the Analog Output set to "MOMENTARY VALUE," and with or without the following options:21) Rack Mounting Plate and Side Rails 2) RS-232 Com Port. Federal Register: Vol. 60, page 39382, 08/02/1995 Horiba Model APMA-3 70 CO Monitor Automated Reference Method: RFCA-0506-158 "Horiba Instruments Incorporated Model APMA-370 Ambient CO Monitor," operated with a full scale fixed measurement range of 0 - 50 ppm, with the automatic range switching off, at any environmental temperature in the range of 20°C to 30°C.2 Federal Register: Vol 71, page 25587, 05/01/2006 MASS-CO, Model 1 CO Analyzer Automated Reference Method: RFCA-1280-050 "MASS-CO, Model 1 Carbon Monoxide Analyzer," operated on a range of 0-50 ppm, with automatic zero and span adjustments at time intervals not to exceed 4 hours, with or without the 100 millivolt and 5 volt output options. The method consists of the following components: (1) Infra-2 (Uras 2) Infrared Analyzer Model 5611-200-35, (2) Automatic Calibrator Model 5869-111, ------- CO List of Designated Reference and Equivalent Methods. December 17.2016 Page 37 (3) Electric Gas Cooler Model 7865-222 or equivalent with pre humidifier, (4) Diaphragm Pump Model 5861-214 or equivalent, (5) Membrane Filter Model 5862-111 or equivalent, (6) Flow Meter Model SK 1171-U or equivalent, (7) Recorder Model Mini Comp DN 1/192 or equivalent. NOTE: This method is not now commercially available. Federal Register: Vol. 45, page 81650,12/11/1980 Monitor Labs Model 8310 CO Analyzer Automated Reference Method: RFCA-0979-041 "Monitor Labs Model 8310 CO Analyzer," operated on the 0-50 ppm range, with a sample inlet filter, with or without any of the following options: 02A Zero/Span Valves 04B Pump (50 Hz) 07A Zero/Span Valve Power Supply 03 A Floor Stand 05A CO Regulator 08A Calibration Valves 04A Pump (60 Hz) 06A CO Cylinder 09A,B,C,D Input Power Transformer Federal Register: Vol. 44, page 54545, 09/20/1979 and Vol 45, page 2700, 01/14/1980 Monitor Labs/Lear Siegler Model 8830 CO Analyzer Automated Reference Method: RFCA-0388-066 "Monitor Labs or Lear Siegler Model 8830 CO Analyzer," operated on the 0-50 ppm range, with a five micron Teflon filter element installed in the rear-panel filter assembly, with or without any of the following options: 2 - Zero/Span Valve Assembly; 3 - Rack Assembly; 4 - Slide Assembly; 7 - 230 VAC, 50/60 Hz. Federal Register: Vol. 53, page 7233, 03/07/1988 MSA/LIRA Model 202S CO Analyzer System Automated Reference Method: RFCA-0177-018 "LIRA Model 202S Air Quality Carbon Monoxide Analyzer System," consisting of a LIRA Model 202S optical bench (P/N 459839), a regenerative dryer (P/N 464084), and rack-mounted sampling system; operated on a 0-50 ppm range, with the slow response amplifier, with or without any of the following options: Remote Meter; Remote Zero and Span Controls; 0-1, 5, 20, Or 50 mA Output; 1-5, 4-20, Or 10-50 mA Output; 0-10 Or 100 mV Output; 0-1, 5, Or 10 Volt Output. Federal Register: Vol. 42, page 5748, 01/31/1977 Peak Laboratories, Model 910-170 Carbon Monoxide Analyzer Automated Equivalent Method: EQCA-0814-217 "Peak Laboratories, Model 910-170 Carbon Monoxide Analyzer", (Mercury replacement- UV photometric method) operated on the standard range of 0-50 ppm and the lower range of 0-1 ppm, at any operating temperature from 20°C to 30°C, using a back-flushing GC scrubber, 99.9999% nitrogen carrier gas at a gas pressure of 60-80 psig, with a column temperature of 105°C, and a detector temperature of 265°C; inlet flow of 20-100 mL/min; in accordance with the associated instrument manual, and with or without any of the following options: rack mount kit, internal sample pump, 4-20 mA output module, particle filter, and data collection software. Federal Register: Vol. 79, page 65392,11/04/2014 Latest modification: 6/2015 SIR S.A. Model S-5006 CO Analyzer Automated Reference Method: RFCA-0708-172 "SIR S.A. Model S-5006 CO Analyzer," operated with full scale fixed measurement ranges 0-50 ppm at any environment temperature in the range of 20°C to 30°C. Federal Register: Vol. 73, page 40866, 07/16/2008 Teledyne Advanced Pollution Instrumentation Models 300,300E, 300EU, T300, T300U or Teledyne Monitor Labs sensor-e™ Model TML-30 CO Analyzer; or recordum airpointer® system module 801-003000; Automated Reference Method: RFCA-1093-093 "Teledyne Advanced Pollution Instrumentation Models 300, 300E, 300EU, T300, T300U or Teledyne Monitor Labs, Inc. sensor-e™ Model TML-30, Gas Filter Correlation Carbon Monoxide Analyzer," operated on any lull scale range between 0-10 ppm and 0-50 ppm (0 - 0.1 ppm for Models 300EU and T300U), at any temperature in the range of 15°C to 35°C for Model 300 or 10°C to 40°C for Models 300E, 300 EU, T300, T300U and TIV1L-30. with a 5-micron TFE filter element or a Kynar® DFU installed in the sample filter assembly, with the dynamic zero and span adjustment set to Offfor Model 300, and with or without any of the following options:2 Option 50, Zero/Span Valves with pressurized span gas and shutoff valve; Option 51, Zero/Span Valves with pressurized span gas and shutoff valve and Internal Zero Air Generator; Option 52, Zero/Span Valves; Option 53, Zero/Span Valves with Internal Zero Air Generator; Rack Mount with slides; RS-232 serial port with status outputs; analog input option;; the NumaView™ software and (for Models 300E, ------- CO List of Designated Reference and Equivalent Methods. December 17.2016 Page 38 300EU, T300, T300U and TML-30) 4-20 mA isolated outputs, airpointer® model 801-003000 only: operated on any full scale range betweenO-lOppm and 0-50 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRM/FEM conform mode; at any temperature in the range of 10°C to 45°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without internal dilution system with internal span gas bottle; with or without modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Note 2 applies to the following Teledyne Advanced Pollution Instrumentation Models 300E, 300EU, T300, T300U, and Teledyne Monitor Labs, Inc. Sensor-e™ Model TML-30. Federal Register: Vol 58, page 58166,10/29/1993 Latest Modification: 08/2010; 05/2013; 07/2014; 9/2015 Teledyne Monitor Labs/Casella/Ecotech Model ML9830/CM2030/EC9830/EC9830T, Teledyne Monitor Labs/Casella/ Ecotech Model ML9830B/CM2030B/EC9830B, or Wedding & Associates Model 1020 CO Analyzers Automated Reference Method: RFCA-0992-088 "Teledyne Monitor Labs, Casella Monitor, or Ecotech Models ML9830/CM2030/EC9830 or ML9830B/CM2030B/ EC9830B, Ecotech Model EC9830T, or Wedding & Associates, Inc. Model 1020 Carbon Monoxide Analyzer;"operated on any full scale range between 0- 5.0 ppm1 and 0-100 ppm, at any temperature in the range of 15°C to 35°C, with the service switch on the secondary panel set to the In position, with the following menu choices selected: Range: 5.0ppm to 100.0 ppm; Over-ranging: Enabled or Disabled; Background: Not Disabled, Calibration: Manual or Timed, Diagnostic Mode: Operate, Filter Type: Kalman; Pres/Temp/Flow Comp: On; Span Comp: Disabled, and as follows: Model ML9830/CM2030/ EC9830/EC9830T: with a five-micron Teflon® filter element installed internally, with the 50-pin I/O board installed on the rear panel configured at any of the following output range settings: Voltage, 0.1V, IV, 5 V, 10V; Current, 0-20 mA, 2-20 mA and 4-20 mA; and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); Valve Assembly for Internal Zero/Span (IZS); Rack Mount Assembly; Internal Floppy Disk Drive. Models ML9830B/CM2030B/ EC9830B and 1020: with either a vendor-supplied or equivalent user-supplied five micron Teflon® filter and exhaust pump, and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); 50-pin I/O board; Rack Mount Assembly; High Pressure Span Valve; hinged, fold-down front panel. Operated with appropriate instrument manual. Federal Register: Vol 57, page 44565, 09/28/1992 Latest Modification: 03/2011 Thermo Electron/Thermo Environmental Instruments Models 48, 48C, 48CTLE, 48i, 48iTLE Automated Reference Method: RFCA-0981-054 "Thermo Electron or Thermo Environmental Instruments, Inc. Model 48 Gas Filter Correlation Ambient CO Analyzer," operated on the 0-50 ppm range, with a time constant setting of 30 seconds, with or without any of the following options: 48-001 Teflon Particulate Filter 48-010 Internal Zero Air Package 48-002 19 Inch Rack Mount 48-488 GPIB (General Purpose Interface Bus) EEEE-488 48-003 Internal Zero/Span Valves with Remote Activation "Thermo Electron or Thermo Environmental Instruments, Inc. Models 48C or 48i Gas Filter Correlation Ambient CO Analyzer," operated on any measurement range between 0-1 ppm1 and 0-100 ppm, with any averaging time setting fro in 10 to 300 seconds, with temperature and/or pressure compensation on or off, operated at temperatures between 20°C and 30°C, with or without any of the following options:2 Teflon particulate filter, Internal zero air scrubber, I/O Expansion board; Model 48C: Carrying handle, 4-20 mA current output, Rack mounts, RS-232 interface, Internal zero/span and sample/calibration solenoid valves, RS-485 interface, Internal zero/span and sample/calibration solenoid valves with remote I/O activation; Models 48C or 48i Trace Level-Enhanced (TLE) Gas Filter Correlation Ambient CO Analyzers operated between 0-1 and 100 ppm with averaging time from 10 to 300 seconds, operated at temperatures between 20° and 30°C at line voltages of 90-110,105-125, and 210-250 VAC @ 50/60 Hz, with or without any of the following options: rack mounts, Teflon® particulate filter, I/O Expansion board, airpointer® Model 801-003000-T: operated on any lull scale range between 0-10 ppm and 0-50 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRM/FEM conform mode; at any internal temperature in the range of 15°C to 45°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without the internal span option as module supplement consisting of an internal dilution system with internal span gas bottle; with or without modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Federal Register: Vol 46, page 47002, 09/23/1981 Latest modifications: 04/2009; 10/2010; 10/2015 ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 39 Nitrogen Dioxide Sodium Arsenite Method for NO2 Manual Equivalent Method: EQN-1277-026 "Sodium Arsenite Method for the Determination of Nitrogen Dioxide in the Atmosphere." Federal Register: Vol. 42, page 62971,12/14/1977 Sodium Arsenite Method for NO2 - Technicon II Manual Equivalent Method: EQN-1277-027 "Sodium Arsenite Method for the Determination of Nitrogen Dioxide in the Atmosphere-Technicon II Automated Analysis System." Federal Register: Vol. 42, page 62971,12/14/1977 TGS-ANSA Method for NO2 Manual Equivalent Method: EQN-1277-028 "TGS-ANSA Method for the Determination of Nitrogen Dioxide in the Atmosphere." Federal Register: Vol. 42, page 62971,12/14/1977 Advanced Pollution Instrumentation, Inc. Model 200 NO2 Analyzer Automated Reference Method: RFNA-0691-082 "Advanced Pollution Instrumentation, Inc. Model 200 Nitrogen Oxides Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with a 5-micron TFE filter element installed in the rear-panel filter assembly, with either a user- or vendor-supplied vacuum pump capable of providing 5 inches mercury absolute pressure at 5 sLpm, with either a user- or vendor-supplied dry air source capable of providing air at a dew point of 0°C or lower, with the following settings of the adjustable setup variables: Adaptive Filter = On PMT Temperature Set Point = 15°C Normal Filter Size = 12 samples Dwell Time = 7 seconds Rate of Change (ROC) Threshold = 10% Dynamic Span = Off Sample Time = 8 seconds Reaction Cell Temperature = 50°C Dynamic Zero = Off and with or without any of the following options: 180 Stainless Steel Valves 283 Internal Zero/Span With Valves (IZS) 356 Level One Spares Kit 184 Pump Pack 325 RS-232/Status Output 357 Level Two Spares Kit 280 Rack Mount With Slides 355 Expendables PE5 Permeation Tube for IZS Federal Register: Vol. 56, page 27014, 06/12/1991 Beckman Model 952-A NOZNO2/NOx Analyzer Automated Reference Method: RFNA-0179-034 "Beckman Model 952-A NO/NCh/NOx Analyzer," operated on the 0-0.5 ppm range with the 5-micron Teflon sample filter (Beckman P/N 861072 supplied with the analyzer) installed on the sample inlet line, with or without the Remote Operation Option (Beckman No. 635539). Federal Register: Vol. 44, page 7806, 02/07/1979 Bendix Model 8101-B Oxides of Nitrogen Analyzer Automated Reference Method: RFNA-0479-038 "Bendix Model 8101-B Oxides of Nitrogen Analyzer," operated on a 0-0.5 ppm range with a Teflon sample filter installed on the sample inlet line and with the following post-manufacture modifications: 1) Ozone generator and reaction chamber input- output tubing modification per Bendix Service Bulletin 8101B-2; 2) The approved converter material; 3) The revised and EPA- approved operation and service manual. These items are mandatory and must be obtained from ABB Process Analytics. The analyzer may be operated with or without any of the following optional modifications: a. Perma Pure dryer/ambient air modification; b. Valve cycle time modification; c. Zero potentiometer centering modification per Bendix Service Bulletin 810 IB-1; d. Reaction chamber vacuum gauge modification. Federal Register: Vol. 44, page 26792, 05/07/1979 ------- no2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 40 Bendix/Combustion Engineering Model 8101-C Oxides of Nitrogen Analyzer Automated Reference Method: RFNA-0777-022 "Bendix or Combustion Engineering Model 8101-C Oxides of Nitrogen Analyzer," operated on a 0-0.5 ppm range with a Teflon sample filter (Bendix P/N 007163) installed on the sample inlet line. Federal Register: Vol. 42, page 37435, 07/21/1977 Columbia Scientific Industries Models 1600 and 5600 Analyzers Automated Reference Method: RFNA-0977-025 "CSI Model 1600 Oxides of Nitrogen Analyzer," operated on a 0-0.5 ppm range with a Teflon sample filter (CSI P/N M951- 8023) installed on the sample inlet line, with or without any of the following options: 951-0103 Rack Ears 951-0114 Recorder Output, 5 V 951-0104 Rack Mounting Kit (Ears & Slides) 951-0115 External Pump (115 V, 60 Hz) 951-0106 Current Output, 4-20 mA (Non-Insulated) 951-8072 Molybdenum Converter Assembly (Horizontal) 951-0108 Diagnostic Output Option 951 -8074 Copper Converter Assembly (Horizontal) 951-0111 Recorder Output, 10 V 951-8079 Copper Converter Assembly (Vertical) 951-0112 Remote Zero/Span Sample Control 951-8085 Molybdenum Converter Assembly (Vertical) NOTE: The vertical molybdenum converter assembly is standard on all new analyzers as of 1-1-87; however, use of any of the other converter assemblies is optional. Also, the above options reflect new CSI part numbers. "CSI Model 5600 Oxides of Nitrogen Analyzer," operated on a 0-0.5 ppm range, with any signal integration time in the range of 20 to 99 seconds, with a Teflon sample filter (CSI P/N M951-8023) installed on the sample inlet line, and with or without any of the following options: 954-0121 - Status Contacts; 964-0126 - Printer; 954-0131 - Rack Mounting Kit (ears and slides); 954-0122 - Input Solenoids; 954-8024 - Cartridge Dryer; 964-0012 - Single Headed Pump - Gast; 954-0125 - Current Output, 4-20 mA; 951-0115 - Single Headed Pump - KNF. Federal Register: Vol. 42, page 46574, 09/16/1977 Dasibi Model 2108 Oxides of Nitrogen Analyzer Automated Reference Method: RFNA-1192-089 "Dasibi Model 2108 Oxides of Nitrogen Analyzer," operated on the 0-500 ppb range, with software revision 3.6 installed in the analyzer, with the auto thumbwheel switch and the diag thumbwheel switch settings at 0, with the following internal CPU dipswitch settings: switch position function 1 open (down) Recorder outputs are NO & NO2 5 open (down) 3 minute time constant 6 closed (up) 3 minute time constant; with a 5-micron Teflon filter element installed in the filter holder, and with or without any of the following options: Built-in Permeation Oven Rack Mounting Three-Channel Recorder Output RS-232 Interface 4-20 mA Output Federal Register: Vol. 57, page 55530,11/25/1992 DKK-TOA Corporation Model GLN-114E Nitrogen Oxides Analyzer Automated Reference Method: RFNA-0798-121 "DKK-TOA Corporation Models GLN-114E and GLN-114E-1 Nitrogen Oxides Analyzer," operated within a temperature range of 20 to 30 degrees C, on any of the following measurement ranges: 0-0.0501, 0-0.1001, 0-0.2001, 0-0.500, and 0-1.000 ppm, and with or without the optional Internal zero air supply and permeation tube oven.2 Federal Register: Vol 63, page 41253, 08/03/1998 DKK-TOA Corporation Model GLN-314E Nitrogen Oxides Analyzer Automated Reference Method: RFNA-0508-171 "DKK-TOA Corporation Model GLN-314E Nitrogen Oxides Analyzer," operated at any temperature in the range of 20°C to 30°C, on any of the following measurement ranges:1 0-0.100 ppm, 0-0.200 ppm, 0-0.500 ppm.2 Federal Register: Vol. 73, page 28819, 05/19/2008 ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 41 Ecotech Serinus 40 Oxides of Nitrogen Analyzer or Opsis AB OPS40 Oxides of Nitrogen Analyzer or Teledyne Analytical Instruments 9110E Oxides of Nitrogen Analyzer or Tisch Environmental TE 4.0 Oxides of Nitrogen Analyzer Automated Reference Method: RFNA-0809-186 "Ecotech Serinus 40 Oxides of Nitrogen Analyzef' or "Opsis AB OPS40 Oxides of Nitrogen Analyzef' or "Teledyne Analytical Instruments 9110E Oxides of Nitrogen Analyzer" or "Tisch Environmental TE 4.0 Oxides of Nitrogen Analyzer," operated in the range of 0-0.5 ppm, with a five-micron Teflon® filter element installed, with either a molybdenum or a vitreous carbon N02 to NO catalyst, and with the following selected: Control Loop-Enabled, Diagnostic Mode-Operate, Pres/Temp/Flow Compensation-Enabled, Span Compensation-Disabled, with concentration automatically corrected for temperature and pressure changes, and operated according to the Serinus 40 Oxides of Nitrogen Analyzer User Manual or the OPS40 Oxides of Nitrogen Analyzer User Manual or the Teledyne Analytical Instruments 9110E Oxides of Nitrogen Analyzer Instruction Manual or Tisch Environmental TE 4.0 Oxides of Nitrogen Analyzer Instruction Manual as appropriate. Federal Register: Vol. 74, page 38184, 07/31/2009 Latest Modifications: 05/2010, 05/2011, 05/2012, 03/2013, 08/2014 Environnement S. A. Model AC31M NO2 Analyzer Automated Reference Method: RFNA-0795-104 "Environnement S. A. Model AC31M Chemiluminescent Nitrogen Oxide Analyzer," operated with a full scale range of 0 - 500 ppb, at any temperature in the range of 15°C to 35°C, with a 5-micron PTFE sample particulate filter, with the following software settings: Automatic response time ON; Minimum response time set to 60 seconds (RT) 2); and with or without any of the following options:2 Internal Permeation Oven; Connection for Silica Gel Dryer; RS232-422 interface; EV3 valve; Internal Printer. Federal Register: Vol 60, page 38326, 07/26/1995 Environnement S. A. Model AC32M NO2 Analyzer Automated Reference Method: RFNA-0202-146 "Environnement S. A. Model AC32M Chemiluminescent Nitrogen Oxides Analyzer," operated with a full scale range of 0 - 500 ppb, at any temperature in the range of 10°C to 35°C, with a 5-micron PTFE sample particulate filter, with response time setting 11 (automatic response time), and with or without the following option: Internal permeation oven. Federal Register: Vol. 67, page 15567, 04/02/2002 Environnement S.A. SANOA Multigas Longpath Monitoring System Automated Reference Method: EQNA-0400-139 "Environnement S.A. Model SANOA Multigas Longpath Air Quality Monitoring System," consisting of a receiver, one or more projectors, interface unit, a user-provided control unit computer running the SANOA VisionAIR software, and associated incidental equipment; configured for measuring NO2, with the temperature control and internal calibration cell options installed, operated with a measurement range of 0 to 0.5 ppm, over an installed monitoring path length of between 27 and 500 meters, within an ambient air temperature range of -30 to +45°C, with a measurement (integrating) time of 180 seconds, and with or without external temperature and barometric pressure sensors or any of the following options: external (meteo) input connection, series 1M bus connection, OGR type projector, analog outputs. Federal Register: Vol. 65, page 26603, 05/08/2000 Environnement S.A. Model AS32M Nitrogen Dioxide Analyzer Automated Equivalent Method: EQNA-1013-210 "Environnement S.A Model AS32M cavity attenuated phase shift spectroscopy Nitrogen Dioxide Analyzef', operated on any lull scale range between 0-500 ppb and 0-1000 ppb, at any ambient temperature in the range of 20°C to 30°C, with automatic response time ON, set to 11, in accoidance with the associated instrument manual; with sample particulate filter, zero gas inlet and zero check enabled; sample permeation diyer. Serial link: 2 RS-232; USB port; Ethernet port (TCP/IP); onboard html web server and, with or without any of the following options: internal permeation bench; ESTEL analog inputs/outputs. Federal Register: Vol. 78, page 67360,11/12/2013 Horiba Instruments Models APNA-360 or APNA-360-CE NO-NO2-NOX Monitor Automated Reference Method: RFNA-0196-111 "Horiba Instruments, Inc. Models APNA-360 or APNA-360-CE Ambient NO-NO2-NOX Monitor," operated with a full scale range of 0 - 0.50 or 0 -1.0 ppm, at any temperature in the range of 10°C to 40°C, with a Line Setting of "MEASURE", and an Analog Output of "MOMENTARY VALUE", and with or without the following options:2 1) Rack Mounting Plate and Side Rails 2) RS-232 Communications Port. Federal Register: Vol 61, page 11404, 03/20/1996 ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 42 Horiba Instruments Model APNA-3 70 NO 2 Monitor Automated Reference Method: RFNA-0506-157 "Horiba Instruments Incorporated Model APNA-370 Ambient NOx Monitor," standard specification, operated with a full scale fixed measurement range of 0 - 0.50 ppm with the automatic range switching off, at any ambient temperature in the range of 20°C to 30°C, and with a 0.3 micrometer sample particulate filter installed.2 Federal Register: Vol 71, page 25587, 05/01/2006 Meloy Model NA530R Nitrogen Oxides Analyzer Automated Reference Method: RFNA-1078-031 "Meloy Model NA530R Nitrogen Oxides Analyzer," operated on the following ranges and time constant switch positions: Range, ppm: 0-0.11 0-0.251 0-0.5 0-1.0 Time Constant Setting: 4 3 or 4 2,3, or 4 2,3, or 4 Operation of the analyzer requires an external vacuum pump, either Meloy Option N-10 or an equivalent pump capable of maintaining a vacuum of 200 torr (22 inches mercury vacuum) or better at the pump connection at the specified sample and ozone-air flow rates of 1200 and 200 cm3/min, respectively. The analyzer may be operated at temperatures between 10°C and 40°C and at line voltages between 105 and 130 volts, with or without any of the following options: N-l A Automatic Zero and Span; N-2 Vacuum Gauge; N-4 Digital Panel Meter; N-6 Remote Control For Zero and Span; N-6B Remote Zero/Span Control and Status (Pulse); N-6C Remote Zero/Span Control and Status (Timer); N-9 Manual Zero/Span; N-10 Vacuum Pump Assembly (See Alternate Requirement Above); N-ll Auto Ranging; N-14B Line Transmitter; N-18 Rack Mount Conversion; N-18A Rack Mount Conversion. Federal Register: Vol. 43, page 50733,10/31/1978 and Vol 44, page 8327, 02/09/1979 Monitor Labs Model 8440E Nitrogen Oxides Analyzer Automated Reference Method: RFNA-0677-021 "Monitor Labs Model 8440E Nitrogen Oxides Analyzer," operated on a 0-0.5 ppm range (position 2 of range switch) with a time constant setting of 20 seconds, with or without any of the following options: TF-Sample Particulate Filter DO-Status Outputs 018A-Ozone Dry Air 018B-Ozone Dry Air - No Drierite With TFE Filter Element R- Rack Mount V- Zero/Span Valves FM- Flow meters Federal Register: Vol. 42, page 37434, 07/21/1977; Vol 42, page 46575, 09/16/1977; Vol 46, page 29986, 06/04/1981 Monitor Labs/Lear Siegler Model 8840 Nitrogen Oxides Analyzer Automated Reference Method: RFNA-0280-042 "Monitor Labs or Lear Siegler Model 8840 Nitrogen Oxides Analyzer," operated on a range of either 0-0.5 or 0-1.0 ppm, with an internal time constant setting of 60 seconds, a TFE sample filter installed on the sample inlet line, with or without any of the following options: 02 Flowmeter 08A Pump Pac Assembly with 09A (115 VAC) 011A Recorder Output 1 Volt 03A Rack Ears 08B Pump Pac Assembly with 09B (100 VAC) 01 IB Recorder Output 100 mV 03B Slides 08C Pump Pac Assembly with 09C (220/240 VAC) 011C Recorder Output 10 mV 05A Zero/Span Valves 08D Rack Mount Panel Assembly 012A DAS Output 1 Volt 05B Valve/Relay 09A Pump 115 VAC 50/60 Hz 012B DAS Output 100 mV 06 Status 09B Pump 100 VAC 50/60 Hz 012C DAS Output 10 mV 07A Input Power Transformer 100 VAC, 50/60 Hz 09C Pump 220/240 VAC 50 Hz 013A Ozone Dry Air 07B Input Power Transformer 220/240 VAC 50 Hz 013B Ozone Dry Air - No Drierite Federal Register: Vol. 45, page 9100, 02/11/1980 and Vol 46, page 29986, 06/04/1981 Monitor Labs/Lear Siegler Model 8841 Nitrogen Oxides Analyzer Automated Reference Method: RFNA-0991-083 "Monitor Labs or Lear Siegler Model 8841 Nitrogen Oxides Analyzer," operated on the 0-0.05 ppm,1 0-0.1 ppm,1 0-0.2 ppm,1 0 - 0.5 ppm, or 0-1.0 ppm range, with manufacturer-supplied vacuum pump or alternative user-supplied vacuum pump capable of providing 200 torr or better absolute vacuum while operating with the analyzer. Federal Register: Vol. 56, page 47473, 09/19/1991 ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 43 Opsis Model AR 500 and System 300 Open Path Ambient Air Monitoring Systems for NO2 Automated Equivalent Method: EQNA-0495-102 "Opsis Model AR 500 System" or "System 300 Open Path (long path) Ambient Air Monitoring Systems," configured for measuring NO2, with one detector and movable grating, operated with a measurement range of 0 to 0.5 ppm, an installed monitoring path length between 50 and 500 meters (or 50 and 1000 meters with the ER 150 option, AR 500 System only), xenon lamp type B (150 watt), fiber optic cable length between 3 and 20 meters; operating within an ambient air temperature range of -50 to +50°C, an analyzer temperature range of 20 to 30°C, a measurement (integrating) time setting between 30 and 120 seconds (0 min:30 sec. to 2 min:00 sec.), and with a complete cycle time of not more than 200 seconds (3 min, 20 sec.). Under this method designation, the Model AR 500 System or System 300 consists of: AR 500 opto-analyser; emitter EM 110 and receiver RE 110 (together identified as ER 110); optic fibre cable OF60-S; power supply PS 150; Opsis operational software, version 7.0 or 7.1; and initial on-site installation, setup, and limited operator training.2 Optional components that can be used with the Model AR 500 only, in addition to or as alternative to corresponding components listed above: • AR 503 opto-analyzer configured as Model AR 500 (only the center detector active, sequential monitoring) • Emitter/receiver ER 150 (for monitoring path lengths up to 1 kilometer) • Transceiver ER 130 and Retroreflector RE 090 with 7 prisms (max. monitoring path length 150 meters) or 12 prisms (max. monitoring path length 250 meters) • Receiver RE 130 • Xenon lamp type A (higher short-wavelength UV output) • Optic fibre cable OF60-R (low-loss for short wavelengths) • Multiplexers MX 004 and MX 024 • Dataloggers DL 010 and DL 016 • Analogue and digital input/output cards AO 008, AI 016, and DI032 • Analogue and digital isolation cards IA 008, ID 008, OA 008, and OD 008 • Window heaters HF 110 and HF 150 • Mirror heaters HM 110 and HM 150 • Auto calibration unit CU 007 • Software packages IO 80 (for the analogue and digital input/output adapters), DL10 and DL16 (for data loggers), ComVision, and STAT 500. Recommended calibration and accuracy audit components (or equivalent) for either Model AR 500 or System 300: • Wavelength calibration lamp CA 004 • Calibration bench CB 100 • Receiver unit RE 060 (two required) • Calibration unit CA 150, with same type lamp as used in the monitoring path emitter • Power supply PS 150 for calibration unit CA 150 • Calibration cells CC 001-X, where X represents various cell lengths from 1 to 900 mm • Filter GG 400 • Special calibration cells CC 110 or CC 150 (for mounting directly on receiver) • Light meter LM 010 Federal Register: Vol 60, page 21518, 05/02/1995 Philips Model PW9762/02 NO/NO:/N(h Analyzer Automated Reference Method: RFNA-0879-040 "Philips Model PW9762/02 NO/NO/NOx Analyzer," consisting of the following components: PW9762/02 Basic Analyzer; PW9729/00 Converter Cartridge; PW9731/00 Sampler or PW9731/20 Dust Filter; operated on a range of 0-0.5 ppm, with or without any of the following accessories: PW9752/00 Air Sampler Manifold; PW9732/00 Sample Line Heater; PW9011/00 Remote Control Set. Federal Register: Vol. 44, page 51683, 09/04/1979 Seres Model NOx 2000 G Nitrogen Dioxide Analyzer Automated Reference Method: RFNA-0706-163 "Seres Model NOx 2000 G Nitrogen Dioxide Ambient Air Analyzer," operated with a full scale measurement range of 1 - 0.50 ppm, at any ambient temperature in the range of 20°C to 30°C. Federal Register: Vol. 71, page 42089, 07/25/2006 SIR S.A. Model S-5012 Nitrogen Oxides Analyzer Automated Reference Method: RFNA-0804-152 "SIR S.A. Model S-5012 Chemiluminescent Nitrogen Oxides Analyzer," operated with a full scale range of 0 - 500 ppb, at any temperature in the range of 20°C to 30°C, with the integration time set to 1 minute, with the "initial zero" disabled, and with a specified Teflon particulate filter installed in the sample inlet filter holder.2 Federal Register: Vol. 69, page 47924, 08/06/2004 Teledyne Advanced Pollution Instrumentation Models 200A, 200'AU, 200E, 200EU, T200, T200U, T204; Teledyne Analytical Instruments Model 911 OA; or Teledyne Monitor Labs sensor-e™ Model TML-41 NO2 Analyzers; or recordum airpointer® System, Module 801-002000; Automated Reference Method: RFNA-1194-099 "Teledyne Advanced Pollution Instrumentation Models 200A, 200AU, 9110A, 200E, 200EU, T200, T200U, T204; Teledyne Analytical Instruments Model 9110A; or Teledyne Monitor Labs, Inc. sensor-e™ Model TML-41 Chemiluminescence Nitrogen Oxides Analyzer," operated on any full scale range between 0-0.05 ppm and 0-1.0 ppm, with a PTFE filter element or a Kynar® DFU installed in the internal filter assembly, with the following software settings: dynamic zero: OFF or ON; dynamic span: OFF; cal-on- ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 44 NO2: OFF; dilution factor: OFF or set to 1.0; autocal: ON or OFF; independent range: ON or OFF; autorange: ON or OFF; temperature/pressure compensation: ON; and with or without any of the following options (if available): rack mounts with or without slides, rack mount for external pump, zero/span valves, 4-20 mA analog outputs, status outputs, RS-232 output; the NumaView™ software. Models 200A, 200E, and T200 and TML-41 only: operated at any temperature in the range of 5°C to 40°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 10 inches mercury or less at 2 sLpm, with or without optional internal zero/span (IZS) and permeation tubes for IZS, gold-plated reaction chamber, or Nafion-type sample gas conditioner, ethernet output, control input, analog input option, RS-485 output. Model 200AU, 200EU, and T200U only: operated at any temperature in the range of 20°C to 30°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 4 inches mercury or less at 1 sLpm Model T204 NOX + 03 Analyzer only: operated on any full scale range between 0- 100 ppb and 0-500 ppb, at any operating temperature from 5°C to 40°C, with either a user-or vendor-supplied vacuum pump capable of providing an absolute pressure of 10 inches mercury or less at 3 sLpm, in accordance with the associated instrument manual, and with or without any of the following options: Zero/Span valves, external communication and data monitoring interfaces. Airpointer® system module 801-002000 only: operated on any full scale range between 0-0.05 ppm and 0-1.0 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRM/FEM conform mode; at any temperature in the range of 10°C to 45°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without internal span option as module supplement consisting of permeation oven and permeation tube; with or without modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Note 2 applies to the following Teledyne Advanced Pollution Instrumentation Models 200E, 200EU, T200, T200U, T204 and Teledyne Monitor Labs, Inc. Sensor-e™ Model TML41. Federal Register: Vol. 59, page 61892,12/02/1994 Latest modifications: 03/2009; 08/2010; 10/2012; 5/2013; 06/2014; 07/2014; 9/2015 Teledyne Advanced Pollution Instrumentation Model 200EUP or T200UP Chemiluminescence Nitrogen Oxides Analyzer Automated Equivalent Method: EQNA-0512-200 "Teledyne Advanced Pollution Instrumentation Model 200EUP or T200UP Chemiluminescence Nitrogen Oxides Analyzer," operated on any full scale range between 0-50 ppb and 0-1000 ppb, with any range mode (Single, Independent, or AutoRange), at any ambient temperature in the range of 20°C to 30°C, equipped with either the nominal or high efficiency photolytic converter, with software Temperature and Pressure compensation ON, in accordance with the associated instrument manual; and with or without any of the following options: Zero/Span Valves, standard serial port (RS232/RS485) or Multi-drop RS- 232, Ethernet port, USB COM port, analog inputs, digital status outputs, analog outputs: 100 mV, IV, 5V, 10V, 4-20 mA current loop outputs; with the Numaview™ software,. Note 2 applies to the following Teledyne Advanced Pollution Instrumentation, Models 200EUP and T200UP. Federal Register: Vol 77, page 32632, 06/01/2012 Latest Modification: 10/2012; 07/2014; 5/2016; 11/2016 Teledyne Advanced Pollution Instrumentation, Model T500U CAPS Nitrogen Dioxide Analyzer Automated Equivalent Method: EQNA-0514-212 "Teledyne Advanced Pollution Instrumentation, Model T500U cavity attenuated phase shift spectroscopy Nitrogen Dioxide Analyzef', operated on any full scale range between 0-50 ppb and 0-1000 ppb, with any range mode (Single, Dual, or AutoRange), at any operating temperature from 5°C to 40°C, with a sample particulate filter, with the following software setting: Temperature and Pressure compensation ON; in accordance with the associated instrument manual, and with or without any of the following options: Zero/Span valves, internal Zero/Span permeation oven (IZS), external communication and data monitoring interfaces; and the NumaView™ software. Note 2 applies to the Teledyne Advanced Pollution Instrumentation, Model T500U. Federal Register: Vol.79, pages 34734-34735, 06/18/2014 Latest modification: 11/2015 Teledyne Advanced Pollution Instrumentation Model T200P Chemiluminescence Nitrogen Oxides Analyzer Automated Equivalent Method: EQNA-1016-241 "Teledyne Advanced Pollution Instrumentation Model T200P Chemiluminescence Nitrogen Oxides Analyzer," operated on any full scale range between 0-50 ppb and 0-1000 ppb, with a PTFE filter element or a Kynar® DFU installed in the filter assembly, with any range mode (Single or Dual), at any operating temperature in the range of 15°C to 35°C, with the high efficiency photolytic converter, with software Temperature and Pressure compensation ON, in accordance with the associated instrument manual; and with or without any of the following options: Zero/Span valves, internal Zero/Span permeation oven (IZS), Nafion-type sample gas conditioner, external communication and data monitoring interfaces; and the NumaView™ software. Note 2 applies to the Teledyne Advanced Pollution Instrumentation, Model T200P. Federal Register: Vol.81, pages 85561-85562,11/28/2016 ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 45 Teledyne Monitor Labs/Casella/Ecotech Models ML9841/CM2041, ML9841A/CM2041A/EC9841A/EC9841T, Teledyne Monitor Labs/Casella/Ecotech ModelML9841B/CM2041B/EC9841B, or Wedding & Associates Model 1030 NO2 Analyzers Automated Reference Method: RFNA-1292-090 "Teledyne Monitor Labs, Casella Monitor, or Ecotech Models ML9841/CM2041, ML9841A/CM2041A/EC9841A, or ML9841B/CM2041B/EC9841B, Ecotech Model 984IT, or Wedding & Associates, Inc. Model 1030 Nitrogen Oxides Analyzers," with either a molybdenum or a vitreous carbon N02 to NO catalyst, operated on any full scale range between 0- 0.05 ppm1 and 0-1.0 ppm, at any temperature in the range of 15°C to 35°C, with the service switch on the secondary panel set to the In position; with the following menu choices selected: Range: 0.05 ppm to 1.0ppm; Over-ranging: Enabled or Disabled, Calibration: Manual or Timed, Diagnostic Mode: Operate; Filter Type: Kalman; Pres/Temp/Flow Comp: On; Span Comp: Disabled, and as follows: Models ML9841/CM2041, ML9841A/CM2041A/EC9841A, and EC9841T - with a five-micron Teflon® filter element installed internally, with the 50-pin I/O board installed on the rear panel configured at any of the following output range setting: Voltage, 0.1V, IV, 5V, 10V; Current, 0-20 mA, 2-20 mA, 4-20 mA; and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); Internal Zero/Span (IZS) Assembly for; Rack Mount Assembly; Internal Floppy Disk Drive. Models ML9841B/CM2041B/EC9841B and 1030 - with a vendor-supplied or equivalent user-supplied five-micron Teflon® filter and exhaust pump, and with or without any of the following options: Valve Assembly for External Zero/Span (EZS); 50-pin I/O board; Internal Zero/Span (IZS) Assembly; Rack Mount Assembly; Charcoal exhaust scrubber; hinged, fold-down front panel. Operated with appropriate instrument manual. Federal Register: Vol. 57, page 60198,12/18/1992 Latest Modification: 03/2011, 03/2013 Thermo Electron/Thermo Environmental Instruments Model 14 B/E Automated Reference Method: RFNA-0179-035 "Thermo Electron or Thermo Environmental Instruments, Inc. Model 14 B/E Chemiluminescent NO/NO2/NOX Analyzer," operated on the 0-0.5 ppm range, with or without any of the following options: 14-001 Teflon Particulate Filter 14-003 Long-Time Signal Integrator 14-005 Sample Flowmeter 14-002 Voltage Divider Card 14-004 Indicating Temperature Controller 14-006 Air Filter Federal Register: Vol. 44, page 7805, 02/07/1979 and Vol.44, page 54545, 09/20/1979 Thermo Electron/Thermo Environmental Instruments Model 141)/E Automated Reference Method: RFNA-0279-037 "Thermo Electron or Thermo Environmental Instruments, Inc. Model 14 D/E Chemiluminescent NO/NO2/NOX Analyzer," operated on the 0-0.5 ppm range, with or without any of the following options: 14-001 Teflon Particulate Filter, 14-002 Voltage Divider Card. Federal Register: Vol. 44, page 10429, 02/20/1979 Thermo Environmental Instruments Models 42, 42C, 42i NO/N02/NOx Analyzer Automated Reference Method: RFNA-1289-074 "Thermo Environmental Instruments Inc. Model 42, Model 42C, or Model 42i Chemiluminescence NO-N02-NOx Analyzer," operated on any measurement range between 0-50 ppb and 0-1000 ppb, with any time average setting from 10 to 300 seconds, with temperature and/or pressure compensation on or off, operated at temperatures between 15°C and 35°C, and with or without an exhaust ozone scrubber or any of the following options: 2 Rack mounts; Internal Zero/span and sample valves with remote activation; Ozone particulate filter; Teflon particulate filter; Ozone permeation dryer; Permeation Oven; RS-232/485 interface, 4-20 mA current output, or I/O expansion board; Model 42 only: Pressure transducer, Sample/ozone flow meters. Model 42/'- TL operated between 10 and 1000 ppb with averaging times from 10 to 300 seconds, operated at temperatures between 15°C and 35°C at line voltages of: a) 90-110 VAC @ 50/60/Hz b) 105-125 VAC @ 50/60/Hz c) 210-250 VAC @ 50/60/Hz and with or without the following options: rack mounts, Teflon® Particle Filter, I/O Expansion Board, airpointer® Model 801-002000-T, operated on any full scale range between 0-0.05 ppm and 0-1.0 ppm, with a PTFE filter element installed in the internal filter assembly, with the software setting: FRM/FEM conform mode; at any internal temperature in the range of 15°C to 39°C, with either a user- or vendor-supplied vacuum pump capable of providing an absolute pressure of 16 inches mercury or less at 2.5 sLpm; installed in the compact, thermally controlled (-40°C to + 45°C) and weather proof airpointer® base unit with integrated data acquisition and management system mounted on a frame, pole, or wall; with or without wireless telemetry; with or without internal span option as module supplement consisting of permeation oven and permeation tube; with or without ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 46 modules for other criteria pollutants; with or without analyzer for particulate matter; with or without additional 3rd party sensors for e.g. meteorology, noise, or traffic counting. Operated with the appropriate instrument manual. Federal Register: Vol. 54, page 50820,12/11/1989 Latest modification: 01/2010; 10/2015 ------- Pb List of Designated Reference and Equivalent Methods. December 17.2016 Page 47 Lead Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) Manual Reference Method: 40 CFRPart 50, Appendix G: RFLA-0813-813 Reference Method for the Determination of Lead in Suspended Particulate Matter Collected from Ambient Air. Federal Register: Vol. 78, page 40000, 7/03/2013 Energy-Dispersive X-Ray Fluorescence Spectrometry (TNRCC) Manual Equivalent Method: EQL-0783-058 "Determination of Lead Concentration in Ambient Particulate Matter by Energy-Dispersive X-Ray Fluorescence Spectrometry (Texas Natural Resource Conservation Commission)," Texas Natural Resource Conservation Commission, P.O. Box 13087, Austin, TX 78711-3087. Federal Register: Vol. 48, page 29742, 06/28/1983 Energy-Dispersive X-Ray Fluorescence Spectrometry (NEA, Inc.) Manual Equivalent Method: EQL-0589-072 "Determination of Lead Concentration in Ambient Particulate Matter by Energy-Dispersive X-Ray Fluorescence Spectrometry (NEA, Inc.)," Nuclear Environmental Analysis, Inc., Suite 260, 10950 SW 5th Street, Beaverton, OR 97005. Federal Register: Vol. 54, page 20193, 05/10/1989 Flame Atomic Absorption Spectroscopy (FAAS) Manual Equivalent Method: EQLA-0813-803 Equivalent Method for the Determination of Lead in Suspended Particulate Matter Collected from Ambient Air. Federal Register: Vol. 78, page 40000, 7/03/2013 Flame Atomic Absorption Spectrometry Manual Equivalent Method: EQL-0380-043 "Determination of Lead Concentration in Ambient Particulate Matter by Flame Atomic Absorption Spectrometry Following Ultrasonic Extraction with Heated HNO3-HCI" Federal Register: Vol. 45, page 14648, 03/06/1980 Flameless Atomic Absorption Spectrometry (EPA/RTP, N.C.) Manual Equivalent Method: EQL-0380-044 "Determination of Lead Concentration in Ambient Particulate Matter by Flameless Atomic Absorption Spectrometry (EPA/RTP, NC)" Federal Register: Vol. 45, page 14648, 03/06/1980 Flameless (Graphite Furnace) Atomic Absorption (Houston, Texas) Manual Equivalent Method: EQL-0895-107 "Determination of Lead Concentration in Ambient Particulate Matter by Flameless (Graphite Furnace) Atomic Absorption (City of Houston, Texas)," Health and Human Services Department, Environmental Chemistry Service, 1115 S. Braeswood, Houston, TX 77030. Federal Register: Vol 60, page 39383, 08/02/1995 Flameless Atomic Absorption Spectrometry (Omaha) Manual Equivalent Method: EQL-0785-059 "Determination of Lead Concentration in Ambient Particulate Matter by Flameless Atomic Absorption Spectrometry (Omaha- Douglas County Health Department)," Omaha-Douglas County Health Department, 1819 Farnam Street, Omaha, NE 68183. Federal Register: Vol 50, page 37909, 09/18/1985 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Doe Run) Manual Equivalent Method: EQL-0196-113 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Doe Run Co.)," Doe Run Company, Smelting Division, 881 Main Street Herculaneum, MO 63048. Federal Register: Vol. 61, page 11404, 03/20/1996 ------- Pb List of Designated Reference and Equivalent Methods. December 17.2016 Page 48 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (EPA/RTP) Manual Equivalent Method: EQL-0380-045 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (EPA/RTP, NC)" Federal Register: Vol. 45, page 14648, 03/06/1980 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (IL) Manual Equivalent Method: EQL-1193-094 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (State of Illinois)," State of Illinois, Environmental Protection Agency, Champaign Inorganic Laboratory, 2120 South First Street, Champaign, IL 61820 Federal Register: Vol. 58, page 61902,11/23/1993 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Kansas) Manual Equivalent Method: EQL-0592-085 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (State of Kansas)," State of Kansas, Department of Health and Environment, Forbes Field, Building 740, Topeka, KS 66620-0001. Federal Register: Vol. 57, page 20823, 05/15/1992 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Montana) Manual Equivalent Method: EQL-0483-057 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (State of Montana)," State of Montana, Department of Health and Environmental Sciences, Cogswell Building, Helena, MT 59620. Federal Register: Vol. 48, page 14748, 04/05/1983 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (NET!) Manual Equivalent Method: EQL-1188-069 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Northern Engineering and Testing, Inc.)," Northern Engineering and Testing, Inc., P.O. Box 30615, Billings, MT 59107. Federal Register: Vol. 53, page 44947,11/07/1988 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (NH) Manual Equivalent Method: EQL-1290-080 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (State of New Hampshire)," State of New Hampshire, Department of Environmental Services, Laboratory Service Unit, 6 Hazen Drive (P.O. Box 95), Concord, NH 03302-0095. Federal Register: Vol. 55, page 49119,11/26/1990 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (PA) Manual Equivalent Method: EQL-0592-086 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Commonwealth of Pennsylvania)," Commonwealth of Pennsylvania, Department of Environmental Resources, P.O. Box 2357, Harrisburg, PA 17105-2357. Federal Register: Vol. 57, page 20823, 05/15/1992 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Pima, AZ) Manual Equivalent Method: EQL-0995-109 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Pima County, Arizona)," Pima County, Wastewater Management Department, 201 North Stone Avenue, Tucson, Arizona 85701-1207. Federal Register: Vol 60, page 54684,10/25/1995 ------- Pb List of Designated Reference and Equivalent Methods. December 17.2016 Page 49 Inductively Coupled Argon Plasma-Mass Spectrometry (Pima Co., AZ) Manual Equivalent Method: EQL-0995-110 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Plasma-Mass Spectrometry (Pima County, Arizona)," Pima County, Wastewater Management Department, 201 North Stone Avenue, Tucson, Arizona 85701-1207. Federal Register: Vol 60, page 54684,10/25/1995 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (RI) Manual Equivalent Method: EQL-0888-068 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (State of Rhode Island)," State ofRhode Island Department of Health, Air Pollution Laboratory, 50 Orms Street, Providence, RI 02904 Federal Register: Vol. 53, page 30866, 08/16/1988 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Silver Valley) Manual Equivalent Method: EQL-1288-070 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (Silver Valley Laboratories)," Silver Valley Laboratories, Inc., P.O. Box 929, Kellogg, ID 83837. Federal Register: Vol. 53, page 48974,12/05/1988 Inductively Coupled Argon Plasma-Atomic Emission Spectrometry (TNRCC) Manual Equivalent Method: EQL-0400-140 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Atomic Emission Spectrometry (TNRCC)," Texas Natural Resource Conservation Commission Laboratory, 5144 E. Sam Houston Parkway N., Houston, TX 77030. Federal Register: Vol. 65, page 26603, 05/8/2000 Inductively Coupled Argon Plasma-Optical Emission Spectrometry (WV) Manual Equivalent Method: EQL-0694-096 "Determination of Lead Concentration in Ambient Particulate Matter by Inductively Coupled Argon Plasma-Optical Emission Spectrometry (State of West Virginia)," State of West Virginia, Department of Commerce, Labor and Environmental Resources, Division of Environmental Protection, 1558 Washington Street East, Charleston, WV 25311-2599 Federal Register: Vol. 59, page 29429, 06/07/1994 Wavelength Dispersive X-Ray Fluorescence Spectrometry (CA) Manual Equivalent Method: EQL-0581-052 "Determination of Lead Concentration in Ambient Particulate Matter by Wavelength Dispersive X-Ray Fluorescence Spectrometry," California Department of Health Services, Air & Industrial Hygiene Laboratory, 2151 Berkeley Way, Berkeley, CA 94704. Federal Register: Vol. 46, page 29986, 06/04/1981 Inductively Coupled Plasma - Mass Spectrometry (Inter-Mountain Labs, Inc.) Manual Equivalent Method: EQL-0310-189 "Procedure for Determination of Lead in Ambient TSP by Hot Plate Acid Extraction and ICP-MS Analysis," where total suspended particulate matter (TSP ) is collected according to 40 CFR Appendix B to part 50, EPA Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method), extracted on a hot plate with 3M HNO3 according to 40 CFR Appendix G to part 50, EPA Reference Method for the Determination of Lead in Suspended Particulate Matter Collected from Ambient Air, and analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) based on EPA SW-846 Method 6020A. Federal Register: Vol. 75, page 9894, 03/04/2010 ------- Pb List of Designated Reference and Equivalent Methods. December 17.2016 Page 50 Inductively Coupled Plasma - Mass Spectrometry (US EPA/OAQPS) Manual Equivalent Method: EQL-0510-191 "Determination of Lead Concentration in TSP by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) with Heated Ultrasonic Nitric and Hydrochloric Acid Filter Extraction," where total suspended particulate matter (TSP) is collected according to 40 CFR Appendix B to part 50, EPA Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method), extracted with a solution of nitric and hydrochloric acids, heated to 80° C and sonicated for one hour, brought to a final volume of 40mL, and analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) based on EPA SW-846 Method 6020A. Federal Register: Vol.75, page 30022, 05/28/2010 Inductively Coupled Plasma - Mass Spectrometry (US EPA/Region 9) Manual Equivalent Method: EQL-0710-192 "Heated Nitric Acid Hot Block Digestion and ICP/MS Analysis for Lead (Pb) on TSP High-Volume Filters." In this method, total suspended particulate matter (TSP) is collected on glass fiber filters according to 40 CFR Appendix B to part 50, EPA Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method), extracted with a solution of nitric acid, heated on a hot block to 95°C for one hour, and brought to a final volume of 50 mL. The lead content of the sample extract is analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) based on EPA Method 200.8 and SW-846 Method 6020A. Federal Register: Vol.75, page 45627, 08/03/2010 Inductively Coupled Plasma-Atomic Emission Spectroscopy (US EPA/OAQPS) Manual Equivalent Method: EQL-0311-196 "Heated Ultrasonic Nitric and Hydrochloric Acid Digestion and ICP/AES Analysis for Lead (Pb) on TSP High-Volume Filters." A sample of total suspended particulate matter (TSP) is collected on a glass fiber filter, using the sampler and procedure of the EPA Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method) (40 CFR 50, Appendix B). The TSP sample is extracted with a solution of nitric and hydrochloric acid, heated in an ultrasonic bath to 80°C for one hour, and brought to a final volume of 40 mL. The lead content of the sample extract is analyzed by Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), based on EPA SW-846 Method 6010C. Federal Register: Vol 76, page 15974, 03/22/2011 Inductively Coupled Plasma- Mass Spectrometry (Eastern Research Group, Inc.) Manual Equivalent Method: EQL-0512-201 "Determination of Lead in TSP by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) with Hot Block Dilute Acid and Hydrogen Peroxide Filter Extraction." In this method, total suspended particulate matter (TSP) is collected on glass fiber filters according to 40 CFR Appendix G to part 50, EPA Reference Method for the Determination of Lead in Suspended Particulate Matter Collected From Ambient Air. The filter samples are extracted in a hot block at 95°C with a solution of dilute hydrochloric acid and nitric acid and two aliquots of hydrogen peroxide, for a total of two and a half hours extraction time. The samples are brought to a final volume of 50 mL and the lead content of the sample extract is analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) based on EPA Compendium Method 10-3.5 and SW-846 Method 6020A. Federal Register: Vol 77, page 32632, 06/01/2012 Inductively Coupled Plasma- Mass Spectrometry (Eastern Research Group, Inc.) Manual Equivalent Method: EQL-0512-202 "Determination of Lead in PMio by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) with Hot Block Dilute Acid and Hydrogen Peroxide Filter Extraction." In this method, PMio particulate matter is collected on Teflon® membrane filters according to 40 CFR Appendix Q to part 50, EPA Reference Method for the Determination of Lead in Particulate Matter as PMio Collected From Ambient Air. The filter samples are extracted in a hot block at 95°C with a solution of hydrochloric acid, nitric acid, and hydrofluoric acid and an aliquot of hydrogen peroxide for a total of two and a half hours extraction time. Samples are brought to a final volume of 50 mL and analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) based on EPA Compendium Method 10-3.5 and SW-846 Method 6020A. Federal Register: Vol 77, page 32632, 06/01/2012 ------- Pb List of Designated Reference and Equivalent Methods. December 17.2016 Page 51 Inductively Coupled Plasma- Mass Spectrometry (South Coast Air Quality Management District Laboratory) Manual Equivalent Method: EQL-0514-213 "Determination of Lead (PB) on TSP Hi-Volume Filters by Microwave Assisted Digestion and Time of Flight Inductively Coupled Plasma Mass Spectrometry (TOFICP-MS)." A sample of total suspended particulate matter (TSP) is collected on a glass fiber filter, using the sampler and procedure of the EPA Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method) (40 CFR 50, Appendix B). The TSP sample is extracted with a solution of nitric and digested in a microwave digestion system at 175° C for 15 minutes, centrifuged for 30 minutes at 2000 rpm, and brought to a final acid concentration of 2-3%. The lead content of the sample extract is analyzed by Time of Flight Inductively Coupled Plasma Mass Spectrometry (TOF ICP-MS), based on EPA SW-846 Method 6010C. Federal Register: Vol.79, pages 34734-34735 06/18/2014 ------- Notes List of Designated Reference and Equivalent Methods. December 17.2016 Page 52 Notes 1 Users should be aware that designation of this analyzer for operation on ranges less than the range specified in the performance specifications for this analyzer (40 CFR 53, Subpart B) is based on meeting the same absolute performance specifications required for the specified range. Thus, designation of these lower ranges does not imply commensurably better performance than that obtained on the specified range. 2 This analyzer is approved for use, with proper factory configuration (if applicable), on either 50 or 60 Hertz line frequency and nominal power line voltages of 115 VAC and 230 VAC, or similar voltages as specified in the operation or instruction manual associated with the method. a For cases with two designation numbers, these methods are dual designated as FRM and FEM. However, where a method is dual designated, EPA considers the method an FRM for purposes of ensuring QA requirements are met. b Method code as available in the AQS data system ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 53 U.S. EPA Reference and Equivalent Methods for Ambient Air Particulate Matter - TSP TSP Manual Method Method Designation No. Method Code" Reference method (high-volume) 802 ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 54 Particulate Matter - PM10 PM10 Samplers Method Designation No. Method Code" Andersen Instruments RAAS10-100 RFPS-0699-130 130 Andersen Instruments RAAS10-200 RFPS-0699-131 131 Andersen Instruments RAAS10-300 RFPS-0699-132 132 BGI or Mesa Laboratories Incorporated Model PQ100 RFPS-1298-124 124 BGI or Mesa Laboratories Incorporated Model PQ200 RFPS-1298-125 125 Ecotech Model 3000 PM10 High Volume Sampler RFPS-0706-162 162 Met One Instruments, Inc. E-FRM- PM10 RFPS-0216-231 231 New Star Environmental Model NS-6070 RFPS-0202-141 141 Oregon DEQ Medium volume sampler RFPS-0389-071 071 Rupprecht & Patashnick Partisol® 2000 RFPS-0694-098 098 R & P Partisol®-FRM 2000 RFPS-1298-126 126 R & P Partisol®-Plus 2025 Seq. RFPS-1298-127 127 Sierra-Andersen/GMW 1200 RFPS-1287-063 063 Sierra-Andersen/GMW 321-B RFPS-1287-064 064 Sierra-Andersen/GMW 321-C RFPS-1287-065 065 Sierra-Andersen/GMW SA241, SA241M Dichot. RFPS-0789-073 073 Thermo Scient fic Partisol® 2000 RFPS-0694-098 098 Thermo Scient fic Partisol® 2000-D, Partisol® 2000/-D EQPS-311-197 197 Thermo Scient fic Partisol® 2000-FRM, Partisol® 2000/ RFPS-1298-126 126 Thermo Scient fic Partisol®-Plus 2025 Seq., Partisol® 2025/ Seq RFPS-1298-127 127 Thermo Scient fic Partisol®-Plus 2025-D Seq., Partisol® 2025/-D Seq EQPS-0311-198 198 Tisch Environmental Model TE-6070 RFPS-0202-141 141 Tisch Environmental Model TE-Wilbur 10 RFPS-0714-216 216 W&A/Thermo Electron Model 600 HVL RFPS-1087-062 062 PM10 Analyzers Method Designation No. Method Code" Andersen Instruments FH62I-N Beta EQPM-0990-076 076 DKK-TOA FPM-222/222C/223/223C EQPM-0905-156 156 DKK-TOA DUB-222(S)/223(S) EQPM-0905-156 156 Environnement S.A. MP101M Beta EQPM-0404-151 151 Horiba APDA-371 EQPM-0798-122 122 Met One BAM1020, GBAM1020, BAM1020-1, GBAM1020-1 Beta EQPM-0798-122 122 Met One Instruments, Inc. E-BAM PLUS EQPM-1215-226 226 Opsis SM200 EQPM-0810-193 193 R & P TEOM® 1400, 1400a EQPM-1090-079 079 SWAM 5a Dual Channel Monitor EQPM-0912-205 205 Teledyne Model 602 BetaPLUS Particle Measurement System EQPM-0912-205 205 Teledyne Model T640 PM Mass Monitor with 640X option EQPM-0516-239 239 Thermo Andersen Series FH 62 C14 Beta Monitor, 5014i Beta EQPM-1102-150 150 Thermo Scientific TEOM® 1400AB, 1405 EQPM-1090-079 079 Thermo Scientific TEOM® 1405-DF with FDMS® EQPM-1013-208 208 W&A/Thermo Electron 650 Beta Gauge EQPM-0391-081 081 ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 55 Particulate Matter - PM2.5 PM2.5 Samplers Method Designation No/' Method Code" Andersen Model RAAS2.5-200 Audit with WINS RFPS-0299-128 128 BGI or Mesa Laboratories Inc. PQ200/200A with WINS RFPS-0498-116 116 BGI or Mesa Laboratories Inc. PQ200-VSCC™ or PQ200A-VSCC™ RFPS-0498-116 or EQPM-0202-142 142 Graseby Andersen RAAS2.5-100 with WINS RFPS-0598-119 119 Graseby Andersen RAAS2.5-300 with WINS RFPS-0598-120 120 Met One Instruments, Inc. E-FRM with WINS RFPS-0315-221 221 Met One Instruments, Inc E-FRM with VSCC™ RFPS-0315-221 521 R & P Partisol®-FRM 2000 PM2.5 with WINS RFPS-0498-117 117 R & P Partisol®-FRM 2000 PM-2.5 Thermo Scientific with VSCC™ RFPS-0498-117 or EQPM-0202-143 143 R & P Partisol® 2000 PM-2.5 Audit with WINS RFPS-0499-129 129 R & P Partisol® 2000 PM-2.5 Audit with VSCC™ RFPS-0499-129 or EQPM-0202-144 144 R & P Partisol®-Plus 2025 PM-2.5 Seq. with WINS RFPS-0498-118 118 R & P Partisol®-Plus 2025 PM-2.5 Seq. with VSCC™ RFPS-0498-118 or EQPM-0202-145 145 Thermo Electron RAAS2.5-100 with VSCC™ RFPS-0598-119 or EQPM-0804-153 153 Thermo Electron RAAS2.5-100 with WINS RFPS-0598-119 119 Thermo Electron RAAS2.5-200 with VSCC™ RFPS-0299-128 or EQPM-0804-154 154 Thermo Electron RAAS2.5-200 with WINS RFPS-0299-128 128 Thermo Electron RAAS2.5-300 with VSCC™ RFPS-0598-120 or EQPM-0804-155 155 Thermo Electron RAAS2.5-300 with WINS RFPS-0598-120 120 Thermo Environmental Model 605 CAPS RFPS-1098-123 123 Thermo Scientific Partisol® 2000-D Dichot., Partisol® 2000/-D Dichot. EQPS-0509-177 177 Thermo Scientific Dichot. Partisol®-Plus Model 2025-D Seq., Partisol® 2025/-D Dichot. Seq. EQPS-0509-179 179 Thermo Scientific Partisol® 2000-FRM, Partisol® 2000/with WINS RFPS-0498-117 117 Thermo Scientific Partisol® 2000-FRM, Partisol® 2000/with VSCC™ RFPS-0498-117 or EQPM-0202-143 143 Thermo Scientific Partisol®-Plus 2025 Seq., Partisol® 2025/ Seq with WINS RFPS-0498-118 118 Thermo Scientific Partisol®-Plus 2025 Seq., Partisol® 2025/ Seq with VSCC™ RFPS-0498-118 or EQPM-0202-145 145 Tisch Environmental Model TE-Wilbur2.5 with WINS RFPS-1014-219 219 Tisch Environmental Model TE-Wilbur 2.5 with VSCC™ RFPS-1014-219 519 Tisch Environmental Model TE-Wilbur 2.5 with Tisch TE-PM2.5C cyclone RFPS-1014-219 or EQPS-0415-223 223 URG-MASS100 with WINS RFPS-0400-135 135 URG-MASS100 with VSCC™ RFPS-0400-135 535 URG-MASS100 with URG-2000-30EGN cyclone EQPS-0316-233 233 ------- PM2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 56 PM2.5 Samplers Method Designation No.'' Method Code" URG-MASS300 RFPS-0400-136 136 URG-MASS300 with VSCC™ RFPS-0400-136 536 URG-MASS300 with URG-2000-30EGN cyclone EQPS-0316-234 234 a For cases with two designation numbers, these methods are dual designated as FRM and FEM. However, where a method is dual designated, EPA considers the method an FRM for purposes of ensuring QA requirements are met. a Method code as available in the AQS data system PM2.5 Analyzers Method Designation No. Method Code" Environnement s.a. Model MP101M PM2.5 Beta Attenuation Monitor EQPM-1013-211 211 Grimm Model EDM 180 PM2.5 Monitor EQPM-0311-195 195 Horiba APDA-371 EQPM-0308-170 170 Met One BAM-1020 PM-2.5 with VSCC™ EQPM-0308-170 170 Met One BAM-1020 PM-2.5 with TE-PM2.5C EQPM-0308-170 570 Met One BAM-1022 Real Time Beta Attenuation Mass Monitor EQPM-1013-209 209 Met One BAM-1022 with TE-PM2.5C EQPM-1013-209 509 Met One BAM-1020 with URG-2000-30EGN Cyclone EQPM-0715-266 266 Thermo Scientific FH62C14-DHS Continuous, 5014i EQPM-0609-183 183 Opsis SM200 EQPM-0812-203 203 SWAM 5a Dual Channel Monitor EQPM-0912-204 204 Teledyne Model 602 BetaPLUS Particle Measurement System EQPM-0912-204 204 Teledyne Model T640 PM Mass Monitor EQPM-0516-236 236 Teledyne Model T640 PM Mass Monitor with 640X option EQPM-0516-238 238 Thermo Scientific Model 5030i Sharp, 5030 SHARP EQPM-0609-184 184 Thermo Scientific TEOM® 1400a with Series 8500C FDMS® EQPM-0609-181 181 Thermo Scientific TEOM® 1405-DF Dichot. with FDMS® EQPM-0609-182 182 Tisch Environmental TE-EDM 180 PM2.5 EQPM-0311-195 195 ------- PMio-2.5 List of Designated Reference and Equivalent Methods. December 17.2016 Page 57 Particulate Matter - PM10-2.5 PM10-2.5 Samplers Method Designation No. Method Code" BGI or Mesa Laboratories, Inc. Model PQ200 PM10-2 5 sampler pair RFPS-1208-173 173 Met One Instruments, Inc. E-FRM PM10-2.5 RFPS-0316-232 232 Thermo Scientific Partisol® 2000-FRM sampler pair, Partisol® 2000/ sampler pair RFPS-0509-175 175 Thermo Scientific Partisol®-Plus 2025 Seq. sampler pair, Partisol® 2025/ Seq sampler pair RFPS-0509-176 176 Thermo Scientific Partisol® 2000-D Dichot., Partisol® 2000/-D Dichot. EQPS-0509-178 178 Thermo Scientific Dichot. Partisol®-Plus Model 2025-D Seq., Partisol® 2025/-D Dichot. Seq. EQPS-0509-180 180 Tisch Environmental Model TE-Wilbur Low-Volume Air Particulate Sampler Pair with WINS RFPS-1014-220 220 Tisch Environmental Model TE-Wilbur Low-Volume Air Particulate Sampler Pair with VSCC™ RFPS-1014-220 520 Tisch Environmental Model TE-Wilbur Low-Volume Air Particulate RFPS-1014-220 or 224 Sampler Pair with Tisch TE-PM2.5C cyclone EQPS-0415-224 PM10-2.5 Analyzers Method Designation No. Method Code" Met One Instruments BAM-1020 System EQPM-0709-185 185 SWAM 5a Dual Channel Monitor EQPM-0912-206 206 Teledyne Model 602 BetaPLUS Particle Measurement System EQPM-0912-206 206 Teledyne Model T640 PM Mass Monitor with 640X option EQPM-0516-240 240 Thermo Scientific TEOM® 1405-DF with FDMS® EQPM-1013-207 207 ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 58 Sulfur Dioxide SO2 Manual Methods Method Designation No. Method Code" Reference method (pararosaniline) — 097 Technicon 1 (pararosaniline) EQS-0775-001 097 Technicon II (pararosaniline) EQS-0775-002 097 SO2 Analyzers Method Designation No. Method Code" Advanced Pollution Instr. 100 EQSA-0990-077 077 Advanced Pollution Instr. 100A/100AS EQSA-0495-100 100 Asarco 500 EQSA-0877-024 024 Beckman 953 EQSA-0678-029 029 Bendix 8303 EQSA-1078-030 030 Casella ML9850, ML9850B, CM2050, CM2050B EQSA-0193-092 092 Columbia Scientific Industries 5700 EQSA-0494-095 095 Dasibi 4108 EQSA-1086-061 061 DKK-TOA Corp. GFS-32 EQSA-0701-115 115 DKK-TOA Corp. GFS-112E, GFS-112E-1 EQSA-0100-133 133 DKK-TOA Corp. GFS-312E EQSA-1107-168 168 Ecotech ML9850/EC9850, ML9850B/EC9850B EQSA-0193-092 092 Ecotech EC9850T EQSA-0193-092 092 Ecotech Serinus 50 EQSA-0809-188 188 Environnement S.A AF21M EQSA-0292-084 084 Environnement S.A AF22M EQSA-0802-149 149 Environnement S.A. SANOA EQSA-0400-138 138 Horiba Model APSA-360/APSA-360ACE EQSA-0197-114 114 Horiba Model APSA-370 EQSA-0506-159 159 Lear Siegler AM2020 EQSA-1280-049 049 Lear Siegler SM1000 EQSA-1275-005 005 Meloy SA185-2A EQSA-1275-006 006 Meloy SA285E EQSA-1078-032 032 Meloy SA700 EQSA-0580-046 046 Monitor Labs 8450 EQSA-0876-013 513 Monitor Labs or Lear Siegler 8850 EQSA-0779-039 039 Monitor Labs or Lear Siegler 8850S EQSA-0390-075 075 Opsis AB OPS50 EQSA-0809-188 188 Opsis AR 500, System 300 (open path) EQSA-0495-101 101 Philips PW9700 EQSA-0876-011 511 Philips PW9755 EQSA-0676-010 010 recordum airpointer® system EQSA-0495-100 100 recordum airpointer® system EQSA-0486-060 060 SERES SF 2000 G EQSA-0810-194 194 SIR S.A. S-5001 EQSA-0507-166 166 Sutron Model 6020 RFSA-0616-237 237 Teledyne Advanced Pollution Inst. 100A, 100 AS, 100E, 100EU, T100, T100U EQSA-0495-100 100 ------- so2 List of Designated Reference and Equivalent Methods. December 17.2016 Page 59 SO2 Analyzers Method Designation No. Method Code" Teledyne Analytical Instruments 6400A EQSA-0495-100 100 Teledyne Analytical Instruments 6400E EQSA-0809-188 188 Teledyne Monitor Labs ML9850, ML9850B EQSA-0193-092 092 Teledyne Monitor Labs TML-50 EQSA-0495-100 100 Thermo Electron 43 EQSA-0276-009 009 Thermo Electron 43A, 43C-TLE, 43/ EQSA-0486-060 060 Thermo Environmental Instruments 43B, 43C EQSA-0486-060 060 Tisch Environmental Model TE 2.0 EQSA-0809-188 188 Wedding 1040 EQSA-0193-092 092 ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 60 Ozone O3 Analyzers Method Designation No. Method Code15 2B Technologies Model 202 EQOA-0410-190 190 2B Technologies Model 211 EQOA-0514-215 215 2B Technologies Model 106 EQOA-0914-218 218 2B Technologies Model POM EQOA-0815-227 227 Advanced Pollution Instr. 400/400A/400E EQOA-0992-087 087 Beckman 950A RFOA-0577-020 020 Bendix 8002 RFOA-0176-007 007 Casella ML9810, ML9810B, ML9811, ML9812, CM2010, CM2010B, CM2011, CM2012 EQOA-0193-091 091 Columbia Scientific Industries 2000 RFOA-0279-036 036 Dasibi 1003-AH, -PC, -RS EQOA-0577-019 019 Dasibi 1008-AH, -PC, -RS EQOA-0383-056 056 DKK-TOA Corp. GUX-113E, GUX-113E-1 EQOA-0200-134 134 DKK-TOA Corp. GUX-313E EQOA-1107-169 169 Ecotech ML9810/EC9810, -9810B, -9811, -9812 EQOA-0193-091 091 Ecotech Serinus 10 EQOA-0809-187 187 Environics 300 EQOA-0990-078 078 Environnement S.A 0341M EQOA-0895-105 105 Environnement S.A 0342M EQOA-0206-148 148 Environnement S.A SANOA EQOA-0400-137 137 Environnement S.A O3 42e EQOA-0515-225 225 Horiba APOA-360 EQOA-0196-112 112 Horiba APOA-370 EQOA-0506-160 160 McMillan 1100-1 RFOA-1076-014 514 McMillan 1100-2 RFOA-1076-015 515 McMillan 1100-3 RFOA-1076-016 016 Meloy OA325-2R RFOA-1075-003 003 Meloy OA350-2R RFOA-1075-004 004 Monitor Labs 8410E RFOA-1176-017 017 Monitor Labs or Lear Siegler 8810 EQOA-O881-053 053 Opsis AB OPS10 EQOA-0809-187 187 Opsis AR 500, System 300 (open path) EQOA-0495-103 103 PCI Ozone Corp. LC-12 EQOA-0382-055 055 Philips PW9771 EQOA-0777-023 023 recordum airpointer® system EQOA-0992-087 087 recordum airpointer® system EQOA-0880-047 047 Seres Model OZ 2000 G EQOA-0506-161 161 SIR S.A. S-5014 EQOA-0207-164 164 Sutron Model 6030 EQOA-0415-222 222 Tanabyte 722, 723, 724, 725, 726 EQOA-0407-165 165 Teledyne Advanced Pollution Instr. 265E, T265 EQOA-0611-199 or RFOA-0216-230 199 Teledyne Advanced Pollution Instr. 400, 400A, 400E, T400 EQOA-0992-087 087 Teledyne Advanced Pollution Instr. T204 EQOA-0514-214 214 Teledyne Advanced Pollution Instr. Model 430 EQOA-1015-229 229 Teledyne Monitor Labs ML9810/9810B, ML9811, ML9812 EQOA-0193-091 091 Teledyne Monitor Labs TML-10 EQOA-0992-087 087 ------- o3 List of Designated Reference and Equivalent Methods. December 17.2016 Page 61 O3 Analyzers Method Designation No. Method Code" Thermo Electron or Thermo Environmental Instruments 49, 49C, 49/ EQOA-0880-047 047 Tisch Environmental TE 1.0 EQOA-0809-187 187 Wedding 1010 EQOA-0193-091 091 ------- CO List of Designated Reference and Equivalent Methods. December 17.2016 Page 62 Carbon Monoxide CO Analyzers Method Designation No. Method Code" Beckman 866 RFCA-0876-012 012 Bendix 8501-5CA RFCA-0276-008 008 Casella ML9830, ML9830B, CM2030, CM2030B RFCA-0992-088 088 Dasibi 3003 RFCA-0381-051 051 Dasibi 3008 RFCA-0488-067 067 DKK-TOA Corp. GFC-311E RFCA-0907-167 167 Ecotech Serinus 30 RFCA-0509-174 174 Ecotech ML9830/EC9830, ML9830B/EC9830B RFCA-0992-088 088 Ecotech EC9830T RFCA-0992-088 088 Environnement S.A CO11M RFCA-0995-108 108 Environnement S.A C012M RFCA-0206-147 147 Environnement S.A C012e RFCA-0915-228 228 Horiba AQM-10, -11, -12 RFCA-1278-033 033 Horiba 300E/300SE RFCA-1180-048 048 Horiba APMA-360 RFCA-0895-106 106 Horiba APMA-370 RFCA-0506-158 158 MASS - CO 1 (Massachusetts) RFCA-1280-050 050 Monitor Labs 8310 RFCA-0979-041 041 Monitor Labs or Lear Siegler 8830 RFCA-0388-066 066 MSA 202S RFCA-0177-018 018 Opsis AB OPS 30 RFCA-0509-174 174 Peak Laboratories Model 910-170 EQCA-0814-217 217 recordum airpointer® system RFCA-1093-093 093 recordum airpointer® system RFCA-0981-054 054 SIR S.A. Model S-5006 RFCA-0708-172 172 Teledyne Adv. Pollution Instr. 300, 300E, 300EU, T300, T300U RFCA-1093-093 093 Teledyne Analytical Instruments GFC7001E RFCA-0509-174 174 Teledyne Monitor Labs ML9830/9830B RFCA-0992-088 088 Teledyne Monitor Labs TML-30 RFCA-1093-093 093 Thermo Electron or Thermo Environmental Instruments 48, 48C, 48/', 48/TLE RFCA-0981-054 054 Tisch Environmental Model TE 3.0 RFCA-0509-174 174 Wedding 1020 RFCA-0992-088 088 ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 63 Nitrogen Dioxide NO2 Manual Methods Method Designation No. Method Code" Sodium arsenite (orifice) EQN-1277-026 084 Sodium arsenite/Technicon II EQN-1277-027 084 TGS-ANSA (orifice) EQN-1277-028 098 NO2 Analyzers Method Designation No. Method Code" Advanced Pollution Instr. 200 RFNA-0691-082 082 Advanced Pollution Instr. 200A/200AU RFNA-1194-099 099 Beckman 952A RFNA-0179-034 034 Bendix 8101-B RFNA-0479-038 038 Bendix 8101-C RFNA-0777-022 022 Casella ML9841, ML9841A, ML9841B, CM2041, CM2041A, CM2041B RFNA-1292-090 090 Columbia Scientific lndust.1600, 5600 RFNA-0977-025 025 Dasibi 2108 RFNA-1192-089 089 DKK-TOA Corp GLN-114E, GLN-114E-1 RFNA-0798-121 121 DKK-TOA Corp GLN-314E RFNA-0508-171 171 Ecotech ML9841A/EC9841 A.ML9841 B/EC9841B RFNA-1292-090 090 Ecotech EC9841T RFNA-1292-090 090 Ecotech Serinus 40 RFNA-0809-186 186 Environnement S.A. AC31M RFNA-0795-104 104 Environnement S.A. AC32M RFNA-0202-146 146 Environnement S.A. SANOA EQNA-0400-139 139 Environnement S.A. AS32M EQNA-1013-210 210 Horiba APNA-360 RFNA-0196-111 111 Horiba APNA-370 RFNA-0506-157 157 Meloy NA530R RFNA-1078-031 031 Monitor Labs 8440E RFNA-0677-021 021 Monitor Labs or Lear Siegler 8840 RFNA-0280-042 042 Monitor Labs or Lear Siegler 8841 RFNA-0991-083 083 Monitor Labs ML9841 RFNA-1292-090 090 Opsis AB OPS40 RFNA-0809-186 186 Opsis AR 500, System 300 (open path) EQNA-0495-102 102 Philips PW9762/02 RFNA-0879-040 040 recordum airpointer system RFNA-1194-099 099 recordum airpointer system RFNA-1289-074 074 Seres Model NOx 2000 G RFNA-0706-163 163 SIR S.A. S-5012 RFNA-0804-152 152 Teledyne Advanced Pollution Inst. 200A, 200AU, 200E, 200EU, T200, T200U, T204 RFNA-1194-099 099 Teledyne Advanced Pollution Inst. T500U EQNA-0514-212 212 Teledyne Advanced Pollution Inst. 200EUP, T200UP EQNA-0512-200 200 Teledyne Advanced Pollution Inst. T200P EQNA-1016-241 241 Teledyne Analytical Instruments 911 OA RFNA-1194-099 099 Teledyne Analytical Instruments 9110E RFNA-0809-186 186 ------- List of Designated Reference and Equivalent Methods. December 17.2016 Page 64 NO2 Analyzers Method Designation No. Method Code" Teledyne Monitor Labs ML9841, ML9841A, ML9841B RFNA-1292-090 090 Teledyne Monitor Labs TML-41 RFNA-1194-099 099 Thermo Electron or Thermo Environmental Instruments 14B/E RFNA-0179-035 035 Thermo Electron or Thermo Environmental Instruments 14D/E RFNA-0279-037 037 Thermo Environmental Instr. 42, 42C, 42/ RFNA-1289-074 074 Tisch Environmental Model TE 4.0 RFNA-0809-186 186 Wedding 1030 RFNA-1292-090 090 ------- Pb List of Designated Reference and Equivalent Methods. December 17.2016 Page 65 Lead Pb Manual Methods Method Designation No. Method Code" H -vol/AAS (alt. extr.) EQL-0380-043 043 H -vol/Energy-disp XRF (TX ACB) EQL-0783-058 058 H -vol/Energy-disp XRF (NEA) EQL-0589-072 072 H -vol/FAAS EQLA-0813-803 803 H -vol/Flameless AA (EMSL/EPA) EQL-0380-044 044 H -vol/Flameless AA (Houston) EQL-0895-107 107 H -vol/Flameless AA (Omaha) EQL-0785-059 059 H -vol/ICAP-OES (Doe Run Co.) EQL-0196-113 113 H -vol/ICAP-OES (EMSL/EPA) EQL-0380-045 045 H -vol/ICAP-OES (Illinois) EQL-1193-094 094 H -vol/ICAP-OES (Kansas) EQL-0592-085 085 H -vol/ICAP-OES (Montana) EQL-0483-057 057 H -vol/ICAP-OES (NE&T) EQL-1188-069 069 H -vol/ICAP-OES (New Hampshire) EQL-1290-080 080 H -vol/ICAP-OES (Pennsylvania) EQL-0592-086 086 H -vol/ICAP-OES (Pima Co.,AZ) EQL-0995-109 109 H -vol/ICAP-MS (Pima Co.,AZ) EQL-0995-110 110 H -vol/ICAP-OES (Rhode Island) EQL-0888-068 068 H -vol/ICAP-OES (Silver Val. Labs) EQL-1288-070 070 H -vol/ICAP-AES (TNRCC) EQL-0400-140 140 H -vol/ICAP-OES (West Virginia) EQL-0694-096 096 H -vol/WL-disp. XRF (CA A&IHL) EQL-0581-052 052 H -vol/ICP-MS (IML, Inc) EQL-0310-189 189 H -Vol/ICP-MS (US EPA/OAQPS) EQL-0510-191 191 H -Vol/ICP-MS (US EPA/Region 9) EQL-0710-192 192 H -Vol/ICP-AES (US EPA/OAQPS) EQL-0311-196 196 H -Vol/ICP-MS (ERG) EQL-0512-201 201 PM10/ICP-MS (ERG) EQL-0512-202 202 Hi-Vol/TOF ICP-MS (SCAQMD) EQL-0514-213 213 ------- Sources/Contacts List of Designated Reference and Equivalent Methods. December 17.2016 Page 66 Sources or Contacts for Designated Reference and Equivalent Methods 2B Technologies, Inc. 2100 Central Ave., Suite 105 Boulder, CO 80301 (303)273-0559 http://www.twobtech.com ABB Process Analytics P.O. Box 831 Lewisburg, WV 24901 (304) 647-4358 Advanced Pollution Instrumentation, Inc. [Refer to Teledyne Advanced Pollution Instrumentation] Andersen Instruments [Refer to Thermo Fisher Scientific, Inc.] ASARCO Incorporated 3422 South 700 West Salt Lake City, UT 84119 (801)262-2459 Beckman Instruments, Inc. Process Instruments Division 2500 Harbor Blvd. Fullerton, CA 92634 (714)871-4848 Bendix [Refer to ABB Process Analytics] BGI Incorporated (Refer to Mesa Labs, Inc.) Casella Monitor Regent House, Wolseley Road, Kempston Bedford, United Kingdom MK42 7JY www.casellameasurement.com Columbia Scientific Industries 11950 Jollyville Road Austin, TX 78759 (800) 531-5003 Combustion Engineering [Refer to ABB Process Analytics] Dasibi Environmental Corp. [Formerly, 506 Paula Avenue Glendale, CA 91201 (818) 247-7601 www.dasibi.com DKK-TOA Corporation 29-10, 1-Chome, Takadanobaba, Shinjuku-ku Tokyo 169-8648, Japan +81-3-3202-0211 www.toadkk.co.ip Eastern Research Group, Inc. 601 Keystone Park Drive, Suite 700, Morrisville, NC 27560 919- 468-7800 www.erg.com Ecotech Pty. Ltd. 1492 Ferntree Gully Rd. Knoxfield, Victoria, 3180, Australia +61 1300 364 946 www.ecotech.com.au Environnement S.A. 111, bd Robespierre 78300 Poissy, France www.environnement-sa.com Instruments also available from: Altech/Environnement U.S.A. 2623 Kaneville Court Geneva, IL 60134 (630) 262- 4400 Environics, Inc. 69 Industrial Park Rd. E. Tolland, CT 06084-2805 (203) 429-0077 www.environics.com FAI Instruments S.R.L Via Aurora, 15 -00013 FonteNuova Rome, Italy (+39) 06.9050248 www.fai-instruments.it Graseby GMW [Refer to Thermo Fisher Scientific, Inc.] GRIMM Technologies, Inc. 5833 Stewart Parkway, Suite 203 Douglasville, GA 30153 (877) 474-6872 www.dustmonitor.com Horiba Instruments Incorporated 17671 Armstrong Avenue Irvine, CA 92714 (800)446-7422 www.horiba.com Inter-Mountain Labs, Inc. 1673 Terra Avenue Sheridan, WY 82801 (307) 672-8945 www.intermountainlabs.com Lear Siegler [Refer to Teledyne Monitor Labs, Inc.] Commonwealth of Massachusetts Department of Environmental Quality Engineering Tewksbury, MA 01876 Mesa Laboratories Inc. 10 Park Place Butler, NC 07405 (973) 492-8400 www.mesalabs.com Met One Instruments, Inc. 1600 Washington Blvd. Grants Pass, OR 97526 (541)471-7111 www.metone.com(metone@metone.com) McMillan [Refer to Columbia Scientific Industries] Mine Safety Appliances 600 Penn Center Blvd. Pittsburgh, PA 15235-5810 (412) 273-5101 Monitor Labs, Inc. [Refer to Teledyne Monitor Labs, Inc.] ------- Sources/Contacts List of Designated Reference and Equivalent Methods. December 17.2016 Page 67 New Star Environmental, LLC 3293 Ashburton Chase NE Roswell, GA 30075 (770)998-2590 Opsls AB Box 244 SE-244 02 Furalund Sweden +46 46 72 25 00 www.opsis.se Instruments also available from Opsls, Inc. 150 N. Michigan Ave., Suite 1950 Chicago, IL 60601 (312) 447-7733 State of Oregon Department of Environmental Quality Air Quality Division 811 S.W. Sixth Avenue Portland, OR 97204 PCI Ozone Corp. One Fairfield Crescent West Caldwell, NJ 07006 (201)575-7052 www.pci-wedeco.com Peak Laboratories, LLC 2330 Old Middlefield Way Suite 10 Mountain View, CA 94043 650-691-1267 www.peaklaboratories.com Phillips Electronic Instruments, Inc. 85 McKee Drive Mahwall, NJ 07430 Recordum Messtechnik GmbH Haus 1/Top 403 Triester Str. 14 A-2351 Wiener Neudorf Austria www.recordum.com Rupprecht & PatashnickCo., Inc. [Refer to Thermo Fisher Scientific, Inc.] Slbata Scientific Technology, Ltd. 1-25, 3-chome Ikenohata, Taito-ku Tokyo 110, Japan 81-3(3822)2272 TTani@email.msn.com Seres 360 Rue Louis de Broglie La Duranne - BP 87000 13793 Aix en Provence - Cedex 3 France +33 (0)4 42 97 37 37 www.seres-france.com SIR SlA. (Sistemas Iratalaaones y Redes, SA.) Avenida de la Industria, 3 Tres Cantos 28760 Madrid, SPAIN (+34) 91 803 66 02 www.sirsa.es SIR USA 826 West Braddock Road Alexandria, VA 22302-3605 (703)837-1883 South Coast Air Quality Management District 21865 Copley Drive Diamond Bar, CA 91765-4182 (909) 396-2269 ilow@aqmd.gov Sutron Air Quality Division 2548 Shell Road Georgetown, TX 78628. 512-869-0544 www, sutron. com/aq Tanabyte Engineering, Inc. 1210 West Burbank Blvd., Suite B, Burbank, CA 91506 (818) 842-4022 www.tanabvte.com Teledyne Advanced Pollution Instrumentation 9970 Carroll Canyon Rd, Suite A San Diego, CA 92131 (858)657-9800 www.teledvne-api .com Teledyne Analytical Instruments 16830 Chestnut Street City of Industry, CA 91748 (626) 934-1622 Teledyne Monitor Labs, Inc. 74 Inverness Drive East Englewood, CO 80112-5189 (303) 792-3300 www.teledvne-ml.com Thermo Electron Corporation [Refer to Thermo Fisher Scientific, Inc.] Thermo Environmental Instruments, Inc. [Refer to Thermo Fisher Scientific, Inc.] Thermo Fisher Scientific, Inc. 81 Wyman Street Waltham, MA 02454 (781) 622-1000 / (800) 678-5599 www.thermo.com Tisch Environmental, Inc. 145 S. Miami Avenue Village of Cleves, OH 45002 (513)467-9000 www.tisch-env.com URG Corporation 116 Merritt Mill Road Chapel Hill, NC 27516 (919) 942-2753 U.S. EPA National Exposure Research Laboratory Human Exposure & Atmospheric Sciences Division Process Modeling Research Branch (MD D205-03) Research Triangle Park, NC 27711 (919)541-5691 www.epa.gov/heasd U.S. EPA Office of Air and Radiation Air Quality Planning and Standards Air Quality Assessment Division (MD C404-03) Research Triangle Park, NC 27711 (919)541-3372 www.epa.gov/air U.S. EPA Region 9 Laboratory 1337 South 46th Street, Bldg 201 Richmond, CA 94804 Wedding and Associates, Inc. [Refer to Thermo Fisher Scientific, Inc.] ------- |