Standard Operating Procedure for Zooplankton Analysis LG403 Revision 07, July 2016 ------- TABLE OF CONTENTS Section Number Subject Page I.0 SCOPE AND APPLICATION 1 2.0 SUMMARY OF METHOD 1 3.0 SAMPLE COLLECTION AM) PRESERVATION 1 4.0 APPARATUS 1 5.0 REAGENTS 2 6.0 ANALYTICAL PROCEDURE ^ MICROCRUSTACEAN SAMPLE ANALYSIS 2 7.0 ANALYTICAL PROCEDURE ^ ROTIFER SAMPLE ANALYSIS 5 8.0 CALCULATION OF MICROCRUSTACEAN AND ROTIFER BIOMASS 6 9.0 CALCULATIONS AM) REPORTING 8 10.0 QUALITY CONTROL AUDITS AND METHODS PRECISION 10 II.0 SAFETY AND WASTE DISPOSAL 10 12.0 REFERENCES 10 FIGURE 1: ZOOPLANKTON SAMPLE SPLITTING DIAGRAM 12 APPENDIX 1: CRUSTACEAN FORMULA FACTORS 13 APPENDIX 2: ROTIFER BIOMASS FORMULA FACTORS 17 Disclaimer: Mention of trade names or commercial products does not constitute endorsement or recommendation for use. ------- Standard Operating Procedure for Zooplankton Analysis Standard Operating Procedure for Zooplankton Analysis 1.0 SCOPE AND APPLICATION 1.1 This method, as developed from Gannon (1971), Stemberger (1979) and Evans etal. (1982), is used to identify and enumerate the zooplankton populations from the Great Lakes. 2.0 SUMMARY OF METHOD 2.1 The method involves microscopic examination of preserved zooplankton samples collected with a conical net towed vertically through a water column. Microcrustacea are examined in four stratified aliquots under a stereoscopic microscope. Rotifera are examined in two equal volume sub-samples under a compound microscope. 3.0 SAMPLE COLLECTION AND PRESERVATION 3.1 See U.S. EPA GLNPO Standard Operation Procedure (SOP) for Zooplankton Sample Collection and Preservation (LG 402). 4.0 APPARATUS 4.1 Most supplies can be acquired from biological supply companies (such as Wildlife Supply Company). The supplies needed are as follows: Dissecting microscope with lOxto 5Ox magnification Compound microscope with lOOxto lOOOx magnification 1-mL Calibrated Hensen-Stempel pipette 100-, 250- and 500-mL graduated cylinders Folsom plankton splitter Ward counting wheel or other suitable counting chamber Sedgwick-Rafter counting cell Cover glass for Sedgwick-Rafter counting cell Microscope slides, 1x3 inch Cover slips Tubes for concentrating plankton samples (see below) Small sieves with 63- and 500-(.un mesh 63-|im Nitex mesh Heavy duty rubber bulb Microprobe Micro-forceps 100- to 500-mL glass jars with split fractions written on labels (2-2048) 4.2 The plankton concentrating tube is constructed by covering one end of a wide glass tube (such as a chromatography tube) with 64-|im mesh. The mesh is secured with O-rings and a heavy-duty bulb is attached to the other end to provide suction. LG403, Revision 07, July 2016 Page 1 ------- Sampling and Analytical Procedures for GLNPO's WQS 5.0 REAGENTS 5.1 Reagents can be ordered through chemical supply companies. CMC has been acquired through Master's Company, Inc. 5.2 The reagents needed are as follows: Formalin (37% formaldehyde solution) Ethanol 5% Sodium hypochlorite solution (Clorox bleach) CMC-9, CMC-10, Hoyer's or other suitable mounting medium for mounting and clearing slide-archived specimens Rose Bengal stain dissolved in ethanol Dilute solution of laboratory detergent 6.0 ANALYTICAL PROCEDURE: MICROCRUSTACEAN SAMPLE ANALYSIS 6.1 Microcrustacean Stratified Splitting 6.1.1 When zooplankton samples are returned to the lab, approximately 1 to 3 mL of Rose Bengal stain solution may be added to each sample to aid in finding the smaller organisms. Samples should be processed one at a time. Under the hood, rinse the sample from the sample bottle through a 63-|im (or smaller) mesh sieve with DI water to remove the formalin. Set the formalin aside under the hood in a sealed labeled bottle to use at the completion of analysis (see 7.4) 6.1.2 Be sure to rinse the sample bottle thoroughly with DI water into the 63-|im (or smaller) mesh sieve to remove any residual organisms adhering to walls of the bottle. All containers from which zooplankton are transferred are to be rinsed thoroughly, including the Folsom splitter, glass jars, and counting chambers. Wash the sample into a glass jar. Adding a small amount of dilute laboratory soap to each sample at this time aids in preventing organisms from sticking to the sides of the containers and from floating at the surface of the sample. 6.1.3 If the sample contains large clumps of Cercopagis, then: 6.1.3.1 Carefully remove the clumps with forceps and place them in a glass tray. 6.1.3.2 Gently rinse the clumps with a stream of DI water in the tray, while pulling at the clumps with forceps to free trapped organisms. 6.1.3.3 Return "freed" organisms other than Cercopagis and Bythotrephes and rinse water to the sample and split as usual. 6.1.3.4 Reserve the clumps of Cercopagis in a separate jar and subsample if abundant (> 250 individuals, see 6.2.1.5). Also note all Bythotrephes identified during this counting process. 6.1.4 Stir the sample gently to break up algal clumps and then pour the entire sample into the Folsom plankton splitter. Stir the sample again in a figure-8 pattern to distribute animals uniformly and split the sample by immediately rotating the splitter before the organisms can settle. Rinse the inside of the splitter well to remove organisms that may stick to the sides. Rinse one sub-sample from the splitter receiving trays and save it in a labeled jar indicating the fraction of total original volume it contains. Page 2 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis 6.1.5 The second sub-sample from the split is placed in the Folsom plankton splitter and divided again. One sub-sample is saved in a labeled jar indicating the fraction of the total original volume it contains. 6.1.6 Repeat Steps 6.1.4 and 6.1.5 as many times as necessary until the last 2 sub-samples contain at least 200 and no more than 400 microcrustaceans each (not including nauplii). These 2 sub-samples represent equal fractions of the original sample. One sub-sample is saved in a jar with the appropriately labeled split, and the other sub-sample is saved in ajar labeled "B". 6.2 Microcrustacean Enumeration 6.2.1 Four sub-samples are to be examined and enumerated. The sub-sample is concentrated by using the small sieve or the condensing tube and placed in a circular (or other suitable) counting chamber. All microcrustaceans are identified and enumerated under a dissecting microscope. The four sub-samples are counted using the criteria listed below in 6.2.1.1, 6.2.1.2, and 6.2.1.3. Refer to Figure 1 for a diagram of the splitting process. 6.2.1.1 The final two sub-samples which contain 200 - 400 organisms (see 6.1.6) are to be counted first. These are referred to as the A and B Counts. All microcrustaceans (except nauplii) are examined and enumerated. The first twenty intact individuals for each SPECCODE are measured for length (Section 8.1). If the sub-samples contain a large amount of algae, it may be necessary to pick out the organisms and transfer them to a clean counting chamber prior to identification. 6.2.1.2 A third sample equal in fraction to the sum of the first two (A + B) samples is examined for subdominant taxa (taxa encountered less than 40 times in A and B counts combined). This is the C Count. 6.2.1.3 A fourth sub-sample equal in fraction to the sum of the first three (A, B, and C) counts is examined for large taxa. This is the D count. Large taxa include Limnocalanus macrurus, Senecella calanoides, Epischura lacustris, Holopedium gibberum, Diaphanosoma birgei, Leptodora kindti and Polyphemus pediculus. If a taxon defined as "large" has a sum of more than 40 individuals in counts A, B, and C, it is not necessary to enumerate them in D count. 6.2.1.4 When a taxa is detected during this sequence of subsampling, all subsamples that this taxa was searched for but not found are referred to as true zero counts. Subsamples for which these taxa were not searched for should be identified with a "-1" in the submission file. In the data submission, number of a taxa for the entire sample (NUMJAR) is calculated by dividing the sum of all subsample counts for a taxa by the proportion of the sample searched. 6.2.1.5 The entire sample must be examined for Mysis, Bythotrephes and Cercopagis. All individuals are counted, but only the first twenty individuals encountered for these three taxa are measured. As previously described, they can be removed from the sample prior to splitting if they are numerous. Otherwise they should be enumerated from A, B, C and D splits as they are examined. After these splits have been counted, pour the uncounted portion through a 500-(.un mesh sieve. Examine the organisms trapped in the sieve for the three taxa. All counts for these three taxa refer to the entire sample (WHOLE, split factor 1). If Cercopagis is numerous (> 250), subsampling of the clump is appropriate. Weighing the clump and the subsample removed provide an estimate of proportion counted, enabling the expansion to an estimate of the whole sample count. The balance used should have precision of at least O.OOlg. Remove as much water as possible from the wet clump before weighing and subsampling. The number reported in the data submission is the estimate for the whole sample, but sample notes should report that this subsampling occurred and include the weights of the clump and subsample and the count of the subsample. LG403, Revision 07, July 2016 Page 3 ------- Sampling and Analytical Procedures for GLNPO's WQS 6.2.1.6 If a backlog in sample analysis occurs, the GLNPO project officer can give permission for a deviation in the protocol for the analysis of D20 counts that omits the "B" subsample. NUMJAR is calculated from only the subsamples searched as described in 6.2.1.4. In this case, if 20 or more individuals of a taxa are counted in the "A" subsample, the analyst does not need to search for the taxa in the "C" subsample. This deviation in sample analysis was granted for: Lake Michigan 2012 Summer, Lake Erie 2012 Spring and Summer, all lakes excepting Lake Ontario 2013 Spring and Summer, Lake Superior 2014 Spring. 6.2.2 General Analysis Guidelines 6.2.2.1 Those organisms requiring higher magnification for identification are examined at 100 - lOOOx magnification under a compound microscope. 6.2.2.2 While counting Microcrustacea, make sure that all organisms are settled to the bottom. It is possible to sink floating Microcrustacea by gently pressing them down using the microprobe or by adding a drop of dilute laboratory detergent. 6.2.2.3 It is necessary to identify and record the sex of all mature Copepods encountered. 6.2.2.4 If replicate samples are collected in the field, all samples from that station should be analyzed by the same analyst. Shallow and deep tows from each station should also be analyzed by the same analyst. 6.2.2.5 If a sample cannot be completely counted and archived within 2 days, the sample should be kept in the refrigerator and a few drops of formalin can be added to the jars to prevent organisms from clumping. Sample analysis should not extend beyond four days. 6.2.2.6 In order to check for consistency of identification and enumeration, analysts can compare their microcrustacean and rotifer results with historical data. On some occasions, analysts may choose to re-examine archived samples in order to confirm identifications or to clarify taxonomic problems. 6.2.2.7 Occasionally, organisms are encountered which do not already appear on the species list. After the taxonomic status of such an organism is determined, the organism should be placed in a labeled vial and preserved with ethanol. The label in the vial should include genus/species name, date preserved, analyst initials, station number, and sample number. This will serve as a voucher specimen. The voucher specimen should be sent out for external confirmation, then a report made to the Work Assignment Manager (WAM) including the distinguishing characteristics used to identify the new organism, and suggestions as to why it has not been encountered in the past (e.g., it is primarily benthic or littoral). Only AFTER written notification of acceptance of the new organism by the WAM should that species be added to the species list. 6.2.2.8 In order to help assure consistency of identification, a voucher specimen collection, based on the species list, should be maintained. Voucher specimens are preserved and stored as stated in 6.2.2.7. 6.2.2.9 It is important that the voucher specimens are checked periodically so lost or damaged animals can be replaced. At least one male and one female (preferably 3-5) representative specimen should be available at all times for examination. Page 4 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis 6.3 Taxonomic References 6.3.1 Adult calanoids are identified according to Balcer el al. (1984). Adult cyclopoids and Harpacticoids are identified according to Hudson el al. (1998). Immature calanoids and cyclopoids are identified to the lowest taxonomic level possible, usually suborder or genus (Czaika 1982). Nauplii are counted with rotifers. Hudson and Lesko (2003) provides supplementary information on Great Lake copepod identification. Malacostracans (i,e.,Mysis relicta) are identified according to Mauchline (1980). Malacostracans are not collected efficiently with our zooplankton tows but they are enumerated and measured for historical purposes. The following cladocerans are identified according to Balcer el al. (1984): Leptodora kindtii, Polyphemuspediculus, Holopedium gibberum, and Diaphanosoma birgei. Brooks (1959) and Evans (1985) are used for all Daphnidae. The remaining cladocerans (Chydoridae, Bosminidae, and Macrothricidae) are classified according to Brooks (1959). Members of Cercopagidae (i.e., Bythotrephes longimanus, and Cercopagis pengoi) are identified according to Rivier (1998). 7.0 ANALYTICAL PROCEDURE: ROTIFER SAMPLE ANALYSIS 7.1 Rotifer, Nauplii and Veliger Sub-sampling 7.1.1 Rotifers, nauplii, and veligers are only counted from the tow taken with the 63-fxm mesh net. Tows taken with the larger mesh (153-|im) will not capture sufficient numbers of these small taxa. 7.1.2 Selection of the split level from which aliquots for rotifer enumeration are taken is based on estimates from previous samples within the data set, or from estimates made during microcrustacean enumeration (rotifers are visible in the dissecting microscope). 7.1.3 Separate 1-mL aliquots are taken from the appropriate split, and rotifers, nauplii and veligers are counted from these aliquots. The goal is to count 200 to 400 animals (rotifers and nauplii, not including veligers). The sample should be mixed thoroughly, and the 1-mL aliquot withdrawn with a Hensen-Stempel pipette (or other precalibrated large-bore pipette). In cases when less than 200 animals are encountered in the 1- mL aliquot, additional 1-mL aliquots can be used for each count (see 7.1.5). 7.1.4 Repeat this process for a duplicate count. These are referred to as A and B counts. 7.1.5 In cases of extremely low rotifer densities, the sample may be concentrated prior to taking aliquots with the pipette. The maximum number of 1-mL aliquots counted from an unsplit sample is 3 per count (i.e., a total of 6 mL), even if the sum does not reach 200 organisms. 7.2 Sedgwick-Rafter Cell Preparation and Rotifer Enumeration 7.2.1 The 1-mL aliquot is placed in a Sedgwick-Rafter cell and covered with a glass cover slip. 7.2.2 All rotifers, microcrustacean nauplii, and Dreissena veligers are identified and enumerated under a compound microscope at lOOx magnification. Length measurements are done on the first 20 intact individuals encountered. Some rotifer species require width measurements (Section 8.2). 7.2.3 Veligers are enumerated for historical record with recognition of the variability in the reproductive cycle of Dreissena. If veligers are extremely abundant (> 100) in the A count, they do not need to be counted in the B count but that deviation must be noted. In those cases, a "-1" should be entered in the ROTB field and ROTAB=ROTA. 7.2.4 After the counts are completed, volume of the split used, including the volume of the aliquots, is measured, and this information and the split factor is recorded in the count spreadsheet. LG403, Revision 07, July 2016 Page 5 ------- Sampling and Analytical Procedures for GLNPO's WQS 7.3 Taxonomic References 7.3.1 Rotifers are identified to genus and to species where possible according to Edmondson (1959) and Stemberger (1976). Some rotifers may be indistinguishable by their gross morphology because of their contracted state; therefore, identification of these organisms is determined by examination of their chitinous mouthparts after using sodium hypochlorite bleach as a clearing agent (Stemberger 1979). This is a time-consuming process that destroys the rotifer and does not often produce clear results. Therefore, in an effort to use lab time efficiently, the bleaching process is most commonly used only as a training technique or in the instance of fairly common organisms with questionable identification. 7.4 Archiving Microcrustacean and Rotifer Samples 7.4.1 After analysis all subsamples are concentrated and returned to the original labeled sample bottle with the original formalin solution from that sample (see 6.1.1). 7.4.2 Sample archiving for a sample set is done after the data submission has been reviewed and accepted. When time to archive, the surface water is siphoned off using a condenser tube or the sample is concentrated using the 63-|im mesh (or smaller) sieve. The concentrated sample is transferred to a 125- mL glass Qorpak bottle. 7.4.3 Fill the sample bottle close to the top with DI and add approximately 5 mL of 37% formalin solution to the sample. 7.4.4 Label the bottle and the storage box with lake, station, lab number, and sample number. All archiving information should be computerized using a word processing program. 8.0 CALCULATION OF MICROCRUSTACEAN AND ROTIFER BIOMASS 8.1 Microcrustacean Biomass 8.1.1 Biomass (dry weight in |ig) of microcrustaceans is calculated from formulas relating some linear measurement (usually body length in mm) to body weight. A compilation of the formula references and constants can be found in Appendix 1. Formulas are derived from a number of sources, but are of the general form: Overall biomass for a taxa is calculated by averaging the dry mass of up to the first 20 measured individuals and multiplying by the density. 8.1.2 Zooplankton may be measured by use of a calibrated eyepiece micrometer or camera lucida/tablet system during the identification and enumeration process, or they may be removed from the sample, photographed with a digital camera, and measurements calculated from the images. The first twenty intact individuals are measured for each taxa. In W = In a + b \nL where: In w In a and b In L natural logarithm of the dry weight estimate (fig) species specific constants (listed in appendix) the length of a measured individual (mm). Page 6 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis Cladocera: Length from the top of the head to the base of the caudal spine or to the end of the carapace. Copepoda: Length from tip of the head to the insertion of spines into the caudal ramus. Mysis: Carapace length, or the length from the tip of the head to the cleft in the telson. Bythotrephes: Body length, excluding the caudal process. Cercopagis: Body length, from the top of the eye to the end of the caudal claws. NOTE: If the organisms are curved or bent, several straight line measurements should be made and summed to obtain total length. 8.1.3 Since the length/weight relationship for Holopedium gibberum was developed based on the length of the foot, the equation from the original reference (Persson and Ekbohm 1980) has been modified for input of the total length, that is assumed to be 4 times the foot length. 8.1.4 Copepoda nauplii follow a length-weight equation appropriate for all life stages of copepods developed by Bottrell et al. 1976. The equation coefficients are in the crustacean factor list (Appendix 1). 8.1.5 Dreissenid veligers follow a length-weight equation developed by Kelly Bowen DFO Canada (personal communication). weight (|ig) = 0.025eA17.5(L in mm) This equation is appropriate for individuals smaller than 300 (.un. 8.2 Rotifer Biomass 8.2.1 Rotifer biomass (|_ig) is calculated according to A. Ruttner-Kolisko (appendix in Bottrell et al. 1976). For most rotifers, calculations use a formula (EQ #1 in Appendix 2) with the general form: Rotifer biomass (|ig) = [(length3 x FF) + (%BV x length3 x FF)] x 10"6 x WW : DW where: jug = biomass of individual Length = total length in |a,m FF = species specific formula factor (see Appendix 2) % BV = volume of appendages as a percent of body biovolume (see Appendix 2) 10"6 = conversion to wet weight; assuming a density of 1 WW:DW = wet weight to dry weight conversion (see 8.2.2) Note that the units of length and width measurements are in |_im in the rotifer formulas and in mm in the crustacean formulas. 8.2.2 A wet weight/dry weight conversion factor of 0.1 (Doohan, 1973) is used for all genera except Asplanchna, for which a factor of 0.039 (Dumont et al., 1975) is used. 8.2.2 For the genus Collotheca, width is measured, and the following formula (EQ #2 in Appendix 2) used: LG403, Revision 07, July 2016 Page 7 ------- Sampling and Analytical Procedures for GLNPO's WQS Collotheca biomass (|ig) = (width3 x FF) x 10"6 x WW : DW 8.2.4 For the genera Conochiloides, Conochilus, Filinia, and Trichocerca, both length and width are measured, and the following formula (EQ #3 in Appendix 2) used: Biomass (|ig) = [(length x width2 x FF) + (%BV x length x width2 x FF)] x 10"6 x WW : DW 8.2.5 The genera Conochiloides and Conochilus, have no appendages (%BV=0) that removes one term from the equation above: 8.2.6 Measurements are made for all intact individuals as follows: 8.2.6.1 Loricate forms: body length from corona to the opposite end at the base of spine (if present). 8.2.6.2 Non-loricate forms: body length from corona to the opposite end, excluding spines, paddles, "toes" or other extensions. 9.0 CALCULATIONS AND REPORTING 9.1 Zooplankton data are reported as number of organisms per cubic meter, which are calculated as follows: 9.1.1 Volume of water filtered: V = a NR A where: V = Volume of water filtered (m3) a = Flow meter calibration factor (see 9.2) Nr = Number of revolutions (read from the flow meter dial) A = Area of the mouth of the net (m2) = 0.19634954 m2 for 0.5-m diameter net 9.1.2 Microcrustacean Densities D = N/(Pt*V) where: D = Density of organisms in numbers per cubic meter N = Number of organisms counted in all splits searched Pt = The proportion of the total sample used to enumerate the taxon (sum of all inverse split factors). V = Volume of water filtered (from 9.1.1) The overall count for a specific taxa in an entire sample is calculated by dividing the total number of organisms counted in all searched splits by the proportion of the sample in which each taxa was enumerated. 9.2 Flowmeters are calibrated during each cruise (see Zooplankton Sample Collection SOP, LG402). The calibration factor is calculated by dividing tow depth in meters by the average number of flowmeter counts recorded during the tows. This information should be recorded in the field notebook for each cruise, and also entered into the field sampling spreadsheet and database. Page 8 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis 9.2.1 The formula for flowmeter calibration is as follows: d a = N R (ave) where: a = Flowmeter calibration d = Sample depth in meters NR(ave) = Number of flowmeter counts, averaged for 20 calibration tows 9.3 Rotifer (and Nauplii) Densities 9.3.1 Calculate the densities of rotifers and nauplii using the following formula: D = (N*Vs)/(Na*V*Ps) where: D = Density of organisms in number per cubic meter N = Number of organisms Na = Number of 1-mL aliquots examined Vs = Volume of split from which aliquots were removed in ml (including aliquots) Ps = The proportion of the total sample represented by the volume from which aliquots were removed (inverse of split factor). V = Volume of water filtered in m3 (from 9.1.1) Density is calculated from the sum of individual counts (ROTAB) taking in consideration the total subsample volume searched (sum of SUBMLA and SUB MLB). For veligers where no B count is done, ROTA is multiplied by 2. 9.4 Data Entry 9.4.1 All microcrustacean and rotifer calculations are made using a spreadsheet program such as Excel or a database program such as Microsoft Access. 9.5 Data Submission to GLNPO 9.5.1 A multi-worksheet Excel data file can be initially submitted electronically for initial review. After final approval the following items are to be submitted on a CD including a cover letter. The date written on the CD should be the date of last changes to the approved data file on the disc. 9.5.2 The data as an Excel file in the GLNPO zooplankton template format. 9.5.3 Electronic copies of all field sheets (pdf format), laboratory count sheets (Excel) and Access database. 9.5.4 Backup/duplicate CD's or DVD's must be made of all data disks submitted to EPA. LG403, Revision 07, July 2016 Page 9 ------- Sampling and Analytical Procedures for GLNPO's WQS 10.0 QUALITY CONTROL AUDITS AND METHODS PRECISION 10.1 In general, ten percent of all samples analyzed are analyzed in duplicate by a second analyst. If a data set has less than 10 samples, at least one sample from that data set should also be analyzed in duplicate. 10.2 For QA counts, the second analyst counts the same split for crustaceans and the same Sedgewick Rafter cell aliquots for rotifers, so that only interanalyst variation is quantified, and not variation associated with sub- 10.3 Results from the second analyst are reported under the same sample number as the original sample, with the exception that the seventh character is replaced by a "Q." 10.4 Percent similarity will be calculated for the samples analyzed in duplicate by two analysts, according to the following formula: a and b are, for a given species, the relative proportions of the total samples A and B, respectively, which that species represents. 10.5 It is expected that the two counts should have a similarity of 90%. If not, the reasons for the discrepancies between analysts should be discussed. If a major difference is found in how the two analysts have been identifying organisms, the last batch of samples that have been counted by the analyst under review may have to be recounted. 11.0 SAFETY AND WASTE DISPOSAL 11.1 Proper PPE should be worn in the laboratory while handling and preparing samples for analyses. Follow all laboratory waste disposal guidelines regarding the disposal of formalin (37% formaldehyde) solutions. Do not discard formalin solutions into the sink unless previously diluted as directed by your laboratory health and safety officer. 12.0 REFERENCES 12.1 Balcer, M.D., N.L. Korda and S.I. Dodson. 1984. Zooplankton of the Great Lakes. A guide to the identification and ecology of the common crustacean species, 174p. Univ. Wise. Press. Madison. 12.2 Bottrell, H.H., A. Duncan, Z.M. Gliwicz, E. Grygierek, A. Herzig, A. Hillbricht-Ilkowska, H. Kurasawa, P. Larsson and T. Weglenska. 1976. A review of some problems in zooplankton production studies. Norw. J. Zool. 12.3 Brooks, J.L. 1959. Cladocera, p. 587-656. In: W.T. Edmondson (ed.) Freshwater Biology, 2nd Ed., Wiley, New York, pp. 1248. 12.4 Czaika, S.C. 1982. Identification of nauplii N1-N6 and copepodids CI-CVI of the Great Lakes calanoid and sampling. K where: 24: 419-456. Page 10 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis cyclopoid copepods (Calanoida, Cyclopoida, Copepoda). J. Great Lakes Res. 8:439-469. 12.5 Doohan, M. 1973. An energy budget for adult Brachionusplicatilis Muller (Rotatoria). Oecologia. 13: 35 1-362. 12.6 Dumont, H.T, van de Velde, I. and Dumont, S. (1975) The dry weight estimate of biomass in a selection of Cladocera, Copepoda and Rotifera from the plankton, periphyton, and benthos of continental waters. Oecologia 19: 225-246. 12.7 Edmondson, W.T. 1959. Rotifers, p. 420-494. In: W.T. Edmondson (ed.) Fresh-water Biology, 2nd Ed., Wiley, New York, pp. 1248. 12.8 Evans, M. 1985. The morphology of Daphniapulicaria, a species newly dominating the offshore southeastern Lake Michigan summer Daphnia community. Trans Amer. Micro. Soc. 104: 223-231. 12.9 Evans, M.S., D.W. Sell and D.I. Page. 1982. Zooplankton studies in 1977 and 1978 at the Donald C. Cook Nuclear Power Plant: Comparisons of preoperational (1971-1974) and operational (1975-1970) population characteristics. Univ. Michigan. Great Lakes Res. Div. Spec. Rep. 89. 12.10 Gannon, J.E. 1971. Two counting cells for the enumeration of Zooplankton micro-Crustacea. Trans Amer. Micros. Soc. 90: 486-490. 12.11 Hawkins, B.E. and Evans, M.S. (1979) Seasonal cycles of zooplankton biomass in Southeastern Lake Michigan. J. Great Lakes Res. 5 (3-4): 256-263. 12.12 Hudson, P.L., and Lesko, L.T. 2003. Free-living and Parasitic Copepods of the Laurentian Great Lakes: Keys and Details on Individual Species. Ann Arbor, MI: Great Lakes Science Center Home Page. http://www.glsc.usgs.gov/greatlakescopepods/ 12.13 Hudson, P.L., Reid, J.W., Lesko, L.T. & Selgeby, J.H. (1998) Cyclopoid and Harpacticoid Copepods of the Laurentian Great Lakes. Ohio Biological Survey Bulletin NS 12(2). 12.14 Makarewicz, J.C. & Jones, D.H. (1990) Occurrence of Bythotrephes cederstromei in Lake Ontario offshore waters. J. Great Lakes Res. 16(1): 143-147. 12.15 Mauchline, J. 1980. The biology of mysids and euphausiids. Advances in Marine Biology 18:373-681. 12.16 Ojaveer, H., L.A. Kuhns, R.P. Barbiero and M.L. Tuchman. 2001. Distribution and population characteristics of Cercopagispengoi in Lake Ontario. J. Great Lakes Res. 27:10-18. 12.17 Rivier, I.K. 1998. The Predatory Cladocera (Onychopoda: Podonidae, Polyphemidae, Cercopagidae) and Leptodorida of the World. Backhuys Publishers, Leiden, The Netherlands, pp.213. 12.18 Shea, M.A. & Makarewicz, J.C. (1989) Production and trophic interactions ofMysis relicta in Lake Ontario. J. Great Lakes Res. 15(2): 223-232. 12.19 Stemberger, R.S. 1979. A guide to rotifers of the Laurentian Great Lakes. U.S. Environmental Protection Agency, Rept. No. EPA 600/4-79-021, 185 pp. LG403, Revision 07, July 2016 Page 11 ------- Sampling and Analytical Procedures for GLNPO's WQS FIGURE 1: ZOOPLANKTON SAMPLE SPLITTING DIAGRAM ORIGINAL SAMPLE \K 1/21 M/ Nk 1/21 This sample portion is held until needed N/ 1/2 n-2 N/ \k 1/2n 2 This sample portion is counted "D" sample r,_ -"j 'j 1/2 1/2 This sample portion is counted \k 1/2' LEGEND: "C" sample N/ 1/2 Both sample portions counted 'B" sample "A" sample "A" and "B" sample: "C": "D": the final split level these sample portions are the two final sample volumes the first preceding sample division the second preceding sample division NOTE: The actual final sample division will be determined by the density of the organisms in the original sample. The first sample volume must have at least 200 organisms but not more than 400 organisms. Page 12 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis APPENDIX 1: CRUSTACEAN FORMULA FACTORS SPECCODE Species LNA B Species Used Reference ACAVERN Acanthocyclops vernalis 1.66 3.97 Mesocyclops edax Rosen 1981 ACRHARP Acroperus harpae 1.167 0.85 Acroperus harpae Dumont et al., 1975 ALNGLOB Alonella qlobulosa 2.1 2.26 Alonella exigua w eggs Dumont et al., 1975 ALOAFFI Alona affinis 2.768 3.84 Alona affinis Dumont et al., 1975 ALOGUTT Alona guttata 2.768 3.84 Alona affinis Dumont et al., 1975 ALOQUAD Alona quadrangularis 2.768 3.84 Alona affinis Dumont et al., 1975 ALORECT Alona rectangula 2.768 3.84 Alona affinis Dumont et al., 1975 ALOSP Alona spp. 2.768 3.84 Alona affinis Dumont et al., 1975 BOSLONG Bosmina longirostris 2.712 2.53 Bosmina longirostris Bottrell et al., 1976 BOSSP Bosmina spp. 2.712 2.53 Bosmina longirostris Bottrell et al., 1976 BYTLONG Bythotrephes longimanus 2.83 2.09 Bythotrephes cederstroemi Makarewicz & Jones (1990) CALCOPE Calanoid copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 CAMRECT Camptocercus rectirostris 2.768 3.84 Alona affinis Dumont et al., 1975 CAMSP Camptocercus spp. 2.768 3.84 Alona affinis Dumont et al., 1975 CANCOPE Canthocamptus copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 CANOREG Canthocamptus oregonensis 1.59 2.59 generic calanoid Burgess et al. 2015 CANROBE Canthocamptus robertcokeri 1.59 2.59 generic calanoid Burgess et al. 2015 CANSP Canthocamptus spp. 1.59 2.59 generic calanoid Burgess et al. 2015 CECPENG Cercopagis pengoi 0.488 2.98 Cercopagis pengoi Ojaveer et al. 2001 CERLACU Ceriodaphnia lacustris 2.83 3.15 Ceriodaphnia reticulata Pace & Orcutt1981 CERRECT Ceriodaphnia reticulata 2.83 3.15 Ceriodaphnia reticulata Pace & Orcutt1981 CERSP Ceriodaphnia spp. 2.83 3.15 Ceriodaphnia reticulata Pace & Orcutt1981 CHYDORI Chydoridae 4.543 3.64 Chydorus sphaericus Rosen 1981 CHYSPHA Chydorus sphaericus 4.543 3.64 Chydorus sphaericus Rosen 1981 COPNAUP Copepod nauplii 1.953 2.4 pooled copepod Bottrell et al., 1976 CYCCOPE Cyclops copepodites 1.66 3.97 Mesocyclops edax Rosen 1981 LG403, Revision 07, July 2016 Page 13 ------- Sampling and Analytical Procedures for GLNPO's WQS SPECCODE Species LNA B Species Used Reference CYCSTRE Cyclops strenuus 1.66 3.97 Mesocyciops edax Rosen 1981 DAPAMBI Daphnia ambigua 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPCATA Daphnia catawba 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPDUBI Daphnia dubia 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPGALEM Daphnia galeata mendotae 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPLAEV Daphnia iaevis 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPLONG Daphnia iongiremis 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPLUMH Daphnia iumhoitzi 0.056 2.84 Daphnia 'pooled' with correction for spine Dumont et al., 1975, with a correction removing proportion of length representing spine (0.58*length) (Cornell) DAPMIDD Daphnia middendorffiana 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPPARV Daphnia parvuia 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPPULE Daphnia puiex 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPPULI Daphnia puiicaria 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPRETR Daphnia retrocurva 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPROSE Daphnia rosea 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPSCHO Daphnia schoedieri 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DAPSP Daphnia spp. 1.603 2.84 Daphnia 'pooled' Dumont et al., 1975 DIACOPE Diaptomid copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 DIAPT Diaptomidae 1.59 2.59 generic calanoid Burgess et al. 2015 DIPBIRG Diaphanosoma birgei 1.289 3.04 Diaphanosoma brachyrum Rosen 1981 DIPSP Diaphanosoma spp. 1.289 3.04 Diaphanosoma brachyrum Rosen 1981 DIYNANU Diacyciops nanus 1.66 3.97 Mesocyciops edax Rosen 1981 DIYTHOM Diacyciops thomasi 1.66 3.97 Mesocyciops edax Rosen 1981 EPICOPE Epischura copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 EPILACU Epischura iacustris 1.59 2.59 generic calanoid Burgess et al. 2015 EUBCORE Eubosmina coregoni 2.712 2.53 Bosmina longirostris Bottrell et al., 1976 EUELAME Eurycercus iameilatus 2.1 2.26 Alonella exigua w eggs Dumont et al., 1975 EURAFFI Eurytemora affinis 1.59 2.59 generic calanoid Burgess et al. 2015 EURCOPE Eurytemora copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 EUYAGIL Eucyciops agiiis 1.66 3.97 Mesocyciops edax Rosen 1981 Page 14 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis SPECCODE Species LNA B Species Used Reference EUYCOPE Eucyclops copepodites 1.66 3.97 Mesocyclops edax Rosen 1981 EUYPRIO Eucyclops prionophorus 1.66 3.97 Mesocyclops edax Rosen 1981 EUYELEG Eucyclops elegans 1.66 3.97 Mesocyclops edax Rosen 1981 GRASP Graptoleberis sp. 2.768 3.84 Alona affinis Dumont et al., 1975 HALSP Halicyclops spp. 1.66 3.97 Mesocyclops edax Rosen 1981 HARCOPE Harpacticoid copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 HARSP Harpacticoida spp. 1.59 2.59 generic calanoid Burgess et al. 2015 HOLGIBB Holopedium gibberum 2.073 3.19 Holopedium gibberum Persson & Ekbohm 1980 original coefficients modified for total length (foot * 4) ILYACUT llyocryptus acutifrons 2.768 3.84 Alona affinis Dumont et al., 1975 ILYSP llyocryptus spp. 2.768 3.84 Alona affinis Dumont et al., 1975 ILYSPIN llyocryptus spinifer 2.768 3.84 Alona affinis Dumont et al., 1975 LATSETI Latona setifera 1.289 3.04 Diaphanosoma brachyrum Rosen 1981 LEOASHL Leptodiaptomus ashlandi 1.59 2.59 generic calanoid Burgess et al. 2015 LEOMINU Leptodiaptomus minutus 1.59 2.59 generic calanoid Burgess et al. 2015 LEOSICI Leptodiaptomus sicilis 1.59 2.59 generic calanoid Burgess et al. 2015 LEOSICO Leptodiaptomus siciloides 1.59 2.59 generic calanoid Burgess et al. 2015 LETKIND Leptodora kindti -0.822 2.67 Leptodora kindti Rosen 1981 LEYQUAD Leydigia quadrangularis 2.768 3.84 Alona affinis Dumont et al., 1975 LEYSP Leydigia spp. 2.768 3.84 Alona affinis Dumont et al., 1975 LIMCOPE Limnocalanus copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 LIMMACR Limnocalanus macrurus 1.59 2.59 generic calanoid Burgess et al. 2015 MACLAT Macrothrix laticornis 2.768 3.84 Alona affinis Dumont et al., 1975 MACSP Macrothrix spp. 2.768 3.84 Alona affinis Dumont et al., 1975 MARALBI Macrocyclops albidus 1.66 3.97 Mesocyclops edax Rosen 1981 MESCOPE Mesocyclops copepodites 1.66 3.97 Mesocyclops edax Rosen 1981 MESEDAX Mesocyclops 1.66 3.97 Mesocyclops edax Rosen 1981 LG403, Revision 07, July 2016 Page 15 ------- Sampling and Analytical Procedures for GLNPO's WQS SPECCODE Species LNA B Species Used Reference edax MICRUBE Microcyclops rubellus 1.66 3.97 Mesocyclops edax Rosen 1981 MOIMICR Moina micrura 1.889 2.57 Moina micrura Dumont et al., 1975 MYSRELI Mysis diluviana 1.266 2.72 Mysis relicta Rudstam et al. 2008 ORTMODE Orthocyclops modestus 1.66 3.97 Mesocyclops edax Rosen 1981 PARCHIT Paracyclops chittoni 1.66 3.97 Mesocyclops edax Rosen 1981 PLEDENT Pleuroxus denticulatus 2.768 3.84 Alona affinis Dumont et al., 1975 PLEPROC Pleuroxus procurvus 2.768 3.84 Alona affinis Dumont et al., 1975 POYPEDI Polyphemus pediculus 2.779 2.15 Polyphemus pediculus Rosen 1981 SCAPSP Scapholeberis spp. 2.416 2.7 Scapholeberis mucronata Dumont et al., 1975 SCAPAURI Scapholeberis aurita 2.416 2.7 Scapholeberis mucronata Dumont et al., 1975 SENCALA Senecella calanoides 1.59 2.59 generic calanoid Burgess et al. 2015 SENCOPE Senecella copepodites 1.59 2.59 generic calanoid Burgess et al. 2015 SIDCRYS Sida crystallina 2.054 2.19 Sida crystallina Rosen 1981 SKIOREG Skistodiaptomus oregonensis 1.59 2.59 generic calanoid Burgess et al. 2015 SKI PALL Skistodiaptomus pallidus 1.59 2.59 generic calanoid Burgess et al. 2015 SKIREIG Skistodiaptomus reighardi 1.59 2.59 generic calanoid Burgess et al. 2015 TROCOPE Tropocyclops copepodites 1.66 3.97 Mesocyclops edax Rosen 1981 TROPRASM Tropocyclops prasinus mexicanus 1.66 3.97 Mesocyclops edax Rosen 1981 Page 16 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis APPENDIX 2: ROTIFER BIOMASS FORMULA FACTORS SPECCODE Species EQ# FF %BV WW:DW ASCECAU Ascomorpha ecaudis 1 0.12 0 0.1 ASCOVAL Ascomorpha ovalis 1 0.12 0 0.1 ASCSALT Ascomorpha saltans 1 0.12 0 0.1 ASCSP Ascomorpha spp. 1 0.12 0 0.1 ASPBRIG Asplanchna briqhtwelli 1 0.23 0 0.039 ASPHERR Asplanchna herricki 1 0.23 0 0.039 ASPPRIO Asplanchna priodonta 1 0.23 0 0.039 BRAANGU Brachionus angularis 1 0.12 0.1 0.1 BRABIDE Brachionus bidentata 1 0.12 0.1 0.1 BRABUDA Brachionus budapestinensis 1 0.12 0.1 0.1 BRACALC Brachionus calyciflorus 1 0.12 0.1 0.1 BRACAUD Brachionus caudatus 1 0.12 0.1 0.1 BRADIVE Brachionus diversicornis 1 0.12 0.1 0.1 BRAHAVA Brachionus havanaensis 1 0.12 0.1 0.1 BRAQUAD Brachionus quadridentatus 1 0.12 0.1 0.1 BRARUBE Brachionus rubens 1 0.12 0.1 0.1 BRASP Brachionus spp. 1 0.12 0.1 0.1 BRAURCE Brachionus urceolaris 1 0.12 0.1 0.1 BRAVARI Brachionus variabilis 1 0.12 0.1 0.1 CEPINTU Cephalodella intuta 1 0.1 0.05 0.1 CEPSP Cephalodella spp. 1 0.1 0.05 0.1 COLMUTA Collotheca mutabilis 2 1.8 0 0.1 COLPELA Collotheca pelagica 2 1.8 0 0.1 COLSP Collotheca spp. 2 1.8 0 0.1 LG403, Revision 07, July 2016 Page 17 ------- Sampling and Analytical Procedures for GLNPO's WQS SPECCODE Species EQ# FF %BV WW:DW CONNATA Conochiloides natans 3 0.26 0 0.1 CONSP Conochiloides spp. 3 0.26 0 0.1 COOUNIC Conochiius unicornis 3 0.26 0 0.1 COUSP Coiureila spp. 1 0.1 0.05 0.1 DICSP Dicranophorus spp. 1 0.035 0 0.1 ENCSP Encentrum spp. 1 0.1 0.05 0.1 EUCALAT Euchianis aiata 1 0.1 0.05 0.1 EUCCALP Euchianis caipidia 1 0.1 0.05 0.1 EUCDILA Euchianis dilatata 1 0.1 0.05 0.1 EUCMENE Euchianis meneta 1 0.1 0.05 0.1 EUCSP Euchianis spp. 1 0.1 0.05 0.1 FILLONG Filinia longiseta 0.52 0.01 0.1 FILTERM Filinia terminalis 0.52 0.01 0.1 GASSP Gastropus spp. 1 0.2 0 0.1 GASSTYL Gastropus stylifer 1 0.2 0 0.1 HEXMIRA Hexarthra mira 1 0.13 0.33 0.1 KELBOST Kellicottia bostoniensis 1 0.03 0.015 0.1 KELLONG Kellicottia lonqispina 1 0.03 0.015 0.1 KERCOCH Keratella cochlearis 1 0.02 0 0.1 KERCOCHH Keratella cochlearis hispida 1 0.02 0 0.1 KERCOCHT Keratella cochlearis f. tecta 1 0.02 0 0.1 KERCRAS Keratella crassa 1 0.02 0 0.1 KEREARL Keratella earlinae 1 0.02 0 0.1 KERHIEM Keratella hiemalis 1 0.22 0.05 0.1 KERQUAD Keratella quadrata 1 0.22 0.05 0.1 KERSP Keratella spp. 1 0.02 0 0.1 KERTAUR Keratella taurocephala 1 0.22 0.05 0.1 KERTEST Keratella testudo 1 0.22 0.05 0.1 KERVALGT Keratella valga f. tropica 1 0.22 0.05 0.1 Page 18 LG403, Revision 07, July 2016 ------- Standard Operating Procedure for Zooplankton Analysis SPECCODE Species EQ# FF %BV WW:DW LECFLEX Lecane flexilis 1 0.1 0.05 0.1 LECSP Lecane spp. 1 0.1 0.05 0.1 LECTENU Lecane tenuiseta 1 0.1 0.05 0.1 LECTUDI Lecane tudicola 1 0.1 0.05 0.1 LEPSP Lepadella spp. 1 0.1 0.05 0.1 LEPTRIP Lepadella triptera 1 0.1 0.05 0.1 MONCOPE Monostyla copeis 1 0.12 0.1 0.1 MONLUNA Monostyla lunaris 1 0.12 0.1 0.1 MONSP Monostyla spp. 1 0.12 0.1 0.1 MYTSP Mytilina spp. 1 0.1 0.05 0.1 NOOSP Notommata spp. 1 0.035 0 0.1 NOTACUM Notholca acuminata 1 0.035 0 0.1 NOTCAUD Notholca caudata 1 0.035 0 0.1 NOTFOLI Notholca foliacea 1 0.035 0 0.1 NOTLABI Notholca labis 1 0.035 0 0.1 NOTLAUR Notholca laurentiae 1 0.035 0 0.1 NOTMICH Notholca michiganensis 1 0.035 0 0.1 NOTSP Notholca spp. 1 0.035 0 0.1 NOTSQUA Notholca squamula 1 0.035 0 0.1 NOTSTRI Notholca striata 1 0.035 0 0.1 PLAPATU Platyias patulus 1 0.22 0.05 0.1 PLOHUDS Ploesoma hudsoni 1 0.1 0 0.1 PLOLENT Ploesoma lenticulare 1 0.1 0 0.1 PLOSP Ploesoma spp. 1 0.1 0 0.1 PLOTRUN Ploesoma truncatum 1 0.1 0 0.1 POLDOLI Polyarthra dolichoptera 1 0.28 0.1 0.1 POLEURY Polyarthra euryptera 1 0.28 0.1 0.1 POLMAJO Polyarthra major 1 0.28 0.1 0.1 POLREMA Polyarthra remata 1 0.28 0.1 0.1 POLSP Polyarthra spp. 1 0.28 0.1 0.1 POLVULG Polyarthra vulgaris 1 0.28 0.1 0.1 POMSULC Pompholyx sulcata 1 0.15 0 0.1 ROTBDEL Rotifera bdelloid 1 0.1 0 0.1 SYNSP Synchaeta spp. 1 0.1 0 0.1 LG403, Revision 07, July 2016 Page 19 ------- Sampling and Analytical Procedures for GLNPO's WQS SPECCODE Species EQ# FF %BV WW:DW TESPARV Testudinella parva 1 0.08 0.1 0.1 TRCPOCI Trichotria pocillum 1 0.1 0.05 0.1 TRCPOCI Trichotria pocillum 1 0.1 0.05 0.1 TRCSP Trichotria spp. 1 0.1 0.05 0.1 TRCTETR Trichotria tetractis 1 0.1 0.05 0.1 TRICAPU Trichocerca capucina 3 0.52 0.006 0.1 TRICYLI Trichocerca cylindrica 3 0.52 0.006 0.1 TRIELON Trichocerca elonqata 3 0.52 0.006 0.1 TRIIERN Trichocerca iernis 3 0.52 0.006 0.1 TRIINSO Trichocerca insolens 3 0.52 0.006 0.1 TRILATA Trichocerca lata 3 0.52 0.006 0.1 TRIMULT Trichocerca multicrinis 3 0.52 0.006 0.1 TRIPORC Trichocerca porcellus 3 0.52 0.006 0.1 TRIPUSI Trichocerca pusilla 3 0.52 0.006 0.1 TRIRATT Trichocerca rattus 3 0.52 0.006 0.1 TRIROUS Trichocerca rousseleti 3 0.52 0.006 0.1 TRISIMI Trichocerca similis 3 0.52 0.006 0.1 TRISP Trichocerca spp. 3 0.52 0.006 0.1 Page 20 LG403, Revision 07, July 2016 ------- |