NCP SUBPART J TECHNICAL NOTEBOOK A COMPENDIUM TO THE NCP PRODUCT SCHEDULE MARCH 2023 (03/01/2023) FOREWORD The U.S. Environmental Protection Agency's (EPA) Office of Emergency Management (OEM) Regulations Implementation Division (RID) compiled the National Oil and Hazardous Substances Pollution Contingency Plan (NCP) Product Schedule, as required by the Clean Water Act, the Oil Pollution Act of 1990 (OPA 90), and the NCP. This NCP Product Schedule Technical Notebook contains a compilation of product bulletins summarizing data requirements and test results for those products listed on EPA's NCP Product Schedule. The Technical Notebook presents information provided by the product manufacturer to include, but is not limited to: contact information, worker health and safety, storage, application methods, toxicity and effectiveness data, and physical properties. Updates to this Technical Notebook, such as the addition of new products to the Schedule, or modifications and/or deletions of listed products, are indicated in bold. NCP Product Schedule Technical Notebook users can navigate to all product bulletins, including aka's, by category type (i.e., Bioremediation Agents, Dispersants, Miscellaneous Oil Spill Control Agents, Surface Collecting Agents, Surface Washing Agents) or alphabetically by clicking on the product link in the Table of Contents; and scrolling through the Navigation Pane. For additional information, please leave a message on EPA's NCP Subpart J Information Line at (202) 260-2342. Written requests may be mailed to: Attention: NCP Product Schedule Manager U.S. Environmental Protection Agency 1200 Pennsylvania Avenue NW Mail Code: 5104-A, Room 1448K William Jefferson Clinton North Building Washington, DC 20460 Disclaimer: [Product Name] is on the U.S. Environmental Protection Agency's NCP Product Schedule. This listing does NOT mean that EPA approves, recommends, licenses, certifies, or authorizes the use of [Product Name] on an oil discharge. The listing means only that data have been submitted to EPA as required by Subpart J of the National Oil and Hazardous Substances Pollution Contingency Plan, Section 300.915. (Source: 40 CFR §300.920 (e)) ------- Currently Listed Number of NCP Product Schedule Products Listed by Category Product Category Bioremediation Agents (B) Dispersants (D) Miscellaneous Oil Spill Control Agents (M) Surface Collecting Agents (S) Surface Washing Agents (SW) Total Products Number of Products 29 19 18 2 62 130 All changes and additions to the NCP Product Schedule Technical Notebook are indicated in bold under the applicable product listing. Changes to the Product Bulletins Product Bulletin Changes Pending EPA Verification: Contact Information Could Not Be Verified (last attempt dates noted on product bulletin): CLEANGREEN® PLANET WASH (SW-44) to include changes to listing letter date, product name, manufacturer contact information, and distributor contact information; and ABLUOL OSASA H/C (SW-75) new product listing. STEP ONE (B-43); SHAMANTRA GREEN (B-68); OIL SOLUTIONS POWDER (M-25); SIMPLE GREEN® (Water Based) (SW-15); PREMIER 99 (SW-12); and EO ALL PURPOSE SOAP-LAVENDER (SW-50). WMI-2000 (B-19); SYSTEM E.T. 20 (B-45); BET BIOPETRO (B-48); LAND AND SEA RESTORATION PRODUCT 001 (VELITE) (B-55); JE1058BS (B-58); PRO-ACT (B-62); DUALZORB® (B-65); ERGOFIT MICRO MIX AQUA (B-67); NEOS AB3000 (D-2); MARE CLEAN 200 (D-3); JD-109 (D-6); JD-2000™ (D-7); BIODISPERS (D-9); SAF-RON GOLD (D-12); ZI-400 (D-13); FFT-SOLUTION® (D-17); CIAGENT (M-17); WASTE-SET #3200® (M-19); WASTE-SET #3400® (M-20); RAPIDGRAB 2000™ (M-24); ELASTOL (M-26); NORSOREX® APX (M-30); CAS 100© (M-31); THICKSLICK 6535 (S-5); SILTECH OP- 40 (S-6); CN-110 (SW-9); DE-SOLV-IT INDUSTRIAL FORMULA (SW-11); NATURE'S WAY HS (SW-18); PETROTECH 25 (SW-21); DO-ALL #18 (SW-24); BG- CLEAN™ 401 (SW-32); E-SAFE© (SW-33); SHEEN- MAGIC© (SW-34); PROCLEANS (SW-35); G-CLEAN OSC-1809 (SW-39); GREEN BEAST™ OIL SPILL & ODOR REMEDIATOR (SW-40); SOC-10 (SW-45); ENVIRONMENTAL 1 CRUDE OIL CLEANER (SW- 47); SANDKLENE 950 (SW-48); DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE (SW-49); VERU-SOLVE™ MARINE 200 HP (SW-52); JEP- li ------- MARINE CLEAN (SW-52); ETHOS CLEAN (SW-58); OSR-IO (SW-59); EPA OIL FIELD SOLUTION™ (SW- 61); and FORMULA 206-lx BIO-WASH™ (SW-66). Note: Products are numbered as they are listed. Numbering may not be consecutive when products are removed from the NCP Product Schedule. For example, Bioremediation Agents begin with B-19. Products numbered B-l through B-18 were removed from the NCP Product Schedule. Updated: 03/01/2023 111 ------- NCP PRODUCT SCHEDULE TECHNICAL NOTEBOOK TABLE OF CONTENTS: LISTING BY PRODUCT CATEGORY BIOREMEDIATION AGENTS: TECHNICAL NOTEBOOK BULLETINS 1 W VI1-2000 2 OPPENHEIMER FORMULA 5 MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL 8 VB591™, VB997™, BINUTRIX® 12 STEP ONE 16 SYSTEM E.T. 20 20 BET BIOPETRO 24 Oil. SPILL EATER II (OSE II) 27 LAND AND SEA RESTORATION PRODUCT 001 (VELITE) 32 S-200C 35 SPILLREMED (MARINE)® 39 JE1058BS 42 BIO WORLD BIOREMEDIATION TREATMENT PRODUCTS (BIOWORLD BHTP) 45 MUNOX SR® 49 SOU. RX 53 PRO-ACT 57 BIOREM-2000 OIL DIGESTER™ 61 DRYLET™ MB BIO 65 DUALZORB® 68 REMEDIADE™ 72 ERGOFIT MIC ROM IX AQUA 76 SHAM ANTRA GREEN 81 SUMP SAFE BIO-RECLAIM 85 WASTE AWAY® 89 ACT TERRA FIRM A 93 PETROCLEAN™ 98 ECOBIOCLEAN® 100 COSW 102 SPILL GENIE™ 3T 107 GHG ORGANIC Ill DISPERSANTS: TECHNICAL NOTEBOOK BULLETINS 115 COREXIT™ EC9527A 116 NEOS AB3000 120 MARE CLEAN 200 123 COREXIT™ EC9500A 126 DISPERSIT SPC 1000™ 130 JD-109 133 JD-2000™ 136 NOKOMIS 3-F4 139 BIODISPERS 142 SEA BRAT #4 145 FINASOL® OSR 52 148 Categorical Table of Contents iv Categorical Table of Contents ------- SAF-RON GOLD 152 Z1-400 155 NOKOMIS 3-AA 158 ACCELL CLEAN® DWD 162 FFT-SOLUTION® 166 MARINE D-BLUE CLEAN™ 170 COREXIT™ EC9500B 173 CHIMEC CHIMSPERSE 6000 177 MISCELLANEOUS OIL SPILL CONTROL AGENTS: TECHNICAL NOTEBOOK BULLETINS 180 PES-51 181 CIAGENT 186 ZYME-FLOW 189 WASTE-SET #3200® 192 WASTE-SET #3400® 195 PX-700® 198 ALSOCUP 201 RAPIIXiRAB 2000™ 204 Oil. SOLUTIONS POWDER 207 ELASTOL 210 OIL BOND® 213 AQUAFLEX® (Open-Cell Elastomeric Sorbents) 216 GELCO 200 219 NORSOREX® APX 223 CAS 100® 228 S-200 OILGONE® 231 HYDRO-BOND™ 234 AQUAPAL® (Open-Cell polyolefin foam Sorbent) 237 SURFACE COLLECTING AGENTS: TECHNICAL NOTEBOOK BULLETINS 240 THICK SLICK 6535 241 SILTECH OP-40 244 SURFACE WASHING AGENTS: TECHNICAL NOTEBOOK BULLETINS 247 TOPS ALL #30 (aka, SUPERALL #38) 248 CN-110 251 COREXIT™ EC9580A 254 DE-SOLV-IT INDUSTRIAL FORMULA 257 PREMIER 99 260 SIMPLE GREEN® 263 AQUACLEAN 266 NATURE'S WAY HS 269 CYTOSOL 272 BIO SOLVE® PINK WATER" 276 Categorical Table of Contents v Categorical Table of Contents ------- PETROTECH 25 279 PI TRO-C I.HAN 282 DO-ALL #18 285 SC-1000™ 288 GOLD CREW SW 291 N ALE-IT 294 1-500 297 i:\yiroci.i :\\ 300 BG-CLEAN™ 401 303 E-SAFE® 306 SHEEN-MAGIC® 309 PROCLEANS 312 SPILLCLEAN 315 TXCHEM HE-1000™ 319 NOKOMIS 5-W 322 G-CLEAN OSC-1809 325 GREEN BEAST™ OIL SPILL & ODOR REMEDIATOR 328 TULXA 331 MARINE GREEN CLEAN™ 334 MARINE GREEN CLEAN PLUS™ 337 CLEANGREEN® PLANET WASH 340 SOC 10 (SURFACE OIL CLEANER) 343 BIOGRASS EXTRA® 346 ENVIRONMENTAL 1 CRUDE OIL CLEANER 349 SANDKLENE 950 352 DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE 355 EO ALL PURPOSE SOAP-LAVENDER 358 DYNAMIC GREEN™ 361 VERU-SOLVE™ MARINE 200 HP 364 NATURAMA G3 A-5 367 SAFEKLEEN 370 CORIBA 700 SR 373 CORIBA 713 SR 376 JEP-MARINE CLEAN 379 ETHOS CLEAN 382 OSR-10 385 ACCELL CLEAN® SWA 388 EPA Oil. FIELD SOLUTION™ 391 PETROMAX PSC 3 394 GREEN TECHNOLOGIES SOLUTIONS-OIL RECOVERY (GTS-OR) 397 SIMPLE GREEN® 2013 Reformulation 400 NONTOX™ SURFACE WASHING AGENT 403 FORMULA 206-lx BIO-WASH™ 406 RHAMNOWASH 10 409 ADP-7 412 Categorical Table of Contents vi Categorical Table of Contents ------- WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE 415 X4JH2000 418 TASMANIA C-CLENZ 421 GOLD CREW® TC 425 DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE 428 ECOGREEN 431 ABLUOL OSASA H/C 434 Categorical Table of Contents vii Categorical Table of Contents ------- NCP PRODUCT SCHEDULE TECHNICAL NOTEBOOK ALPHABETICAL LIST OF ALL PRODUCT BULLETINS ABLUOL OSASA II/C 434 ACCELL CLEAN® DWD 162 ACCELL CLEAN® SWA 388 ACT TERRA FIRM A 93 ADP-7 412 ALSOCUP 201 AQUACLEAN 266 AQUAFLEX® (Open-Cell Elastomeric Sorbents) 216 AQUAPAL® (Open-Cell polyolefin foam Sorbent) 237 BET BIOPETRO 24 BG-CLEAN™ 401 303 BIODISPERS 142 BIOGRASS EXTRA® 346 BIOREM-2000 OIL DIGESTER™ 61 BIO SOLVE® PINK WATER" 276 BIO WORLD BIOREMEDIATION TREATMENT PRODUCTS (BIOWORLD BHTP) 45 CAS 100® 228 CIIIYIHC CHIMSPERSE 6000 177 CIAGENT 186 CLEANGREEN® PLANET WASH 340 CN-110 251 COREXIT™ EC9500A 126 COREXIT™ EC9500B 173 COREXIT™ EC9527A 116 COREXIT™ EC9580A 254 CORIBA 700 SR 373 CORIBA 713 SR 376 CYTOSOL 272 DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE 428 DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE 355 DE-SOLV-IT INDUSTRIAL FORMULA 257 DISPERSIT SPC 1000™ 130 DO-ALL #18 285 DRYLET™ MB BIO 65 DUALZORB® 68 DYNAMIC GREEN™ 361 ECOBIOCLEAN® 100 COSW 102 ECOGREEN 431 ELASTOL 210 i:\yiroci.i :\\ 300 ENVIRONMENTAL 1 CRUDE Oil. CLEANER 349 Alphabetical Table of Contents viii Alphabetical Table of Contents ------- IX) ALL PURPOSE SOAP-LAVENDER 358 EPA Oil. FIELD SOLUTION™ 391 ERGOFIT MIC ROM IX AQUA 76 E-SAFE® 306 ETHOS CLEAN 382 1-500 297 FFT-SOLUTION® 166 FINASOL® OSR 52 148 FORMULA 206-lx BIO-WASH™ 406 G-CLEAN OSC-1809 325 GHG ORGANIC Ill GELCO 200 219 GOLD CREW SW 291 GOLD CREW® TC 425 GREEN BEAST™ OIL SPILL & ODOR REMEDIATOR 328 GREEN TECHNOLOGIES SOLUTIONS-OIL RECOVERY (GTS-OR) 397 HYDRO-BOND™ 234 JD-109 133 JD-2000™ 136 JE1058BS 42 JEP-MARINE CLEAN 379 LAND AND SEA RESTORATION PRODUCT 001 (VELITE) 32 MARE CLEAN 200 123 MARINE D-BLUE CLEAN™ 170 MARINE GREEN CLEAN™ 334 MARINE GREEN CLEAN PLUS™ 337 MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL 8 MUNOX SR® 49 N ALE-IT 294 NATURAMA G3 A-5 367 NATURE'S WAY HS 269 NEOS AB3000 120 NOKOMIS 3-AA 158 NOKOMIS 3-F4 139 NOKOMIS 5-W 322 NONTOX™ SURFACE WASHING AGENT 403 NORSOREX® APX 223 OIL BOND® 213 OIL SOLUTIONS POWDER 207 OIL SPILL EATER II (OSE II) 27 OPPENHEIMER FORMULA 5 OSR-10 385 PES-51 181 PETRO-CLEAN 282 PETROCLEAN™ 98 Alphabetical Table of Contents ix Alphabetical Table of Contents ------- PETROMAX PSC 3 3 PETROTECH 25 2 PREMIER 99 2 PRO-ACT PROCLEANS 3 PX-700® 1 RAPIIXiRAB 2000™ 2 REMEDIADE™ RHAMNOWASH 10 4 S-200 OILGONE® 2 S-200C SAFE KLEEN 3 SAF-RON GOLD 1 SANDKLENE 950 3 SC-1000™ 2 SEA BRAT #4 1 SHAM ANTRA GREEN SHEEN-MAGIC® 3 SILTECH OP-40 2 SIMPLE GREEN® 2 SIMPLE GREEN® 2013 Reformulation 4 SOC 10 (SURFACE OIL CLEANER) 3 SOIL RX SPILLCLEAN 3 SPILL GENIE™ 3T 1 SPILLREMED (MARINE)® STEP ONE SUMP SAFE BIO-RECLAIM SYSTEM E.T. 20 TASMANIA C-CLENZ 4 THICK SLICK 6535 2 TOPS ALL #30 (aka, SUPERALL #38) 2 TULXA 3 TXCHEM HE-1000™ 3 VB591™, VB997™, BINUTRIX® VERU-SOLVE™ MARINE 200 HP 3 WASTE AWAY® WASTE-SET #3200® 19 WASTE-SET #3400® 19 WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE 41 X4JH2000 41 W VI1-2000 Z1-400 155 ZYME-FLOW 189 Alphabetical Table of Contents x Alphabetical Table of Contents ------- BIOREMEDIATION AGENTS: TECHNICAL NOTEBOOK BULLETINS Bioremediation Agents 1 Bioremediation Agents ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 9/07/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #B-19 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JUNE 18, 1990 REVISED LISTING DATE: JANUARY 11, 1996 "WMI-2000" I. NAME, BRAND, OR TRADEMARK WMI-2000 Type of Product: Biological Additive II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT WMI International, Inc. Mailing Address 2104 Brentwood Drive WMI International, Inc. Houston, TX 77019 P.O. Box 130583 Phone: updated information required Houston, TX 77219 Mobile: updated information required (Mr. Joseph F. Jennings, President) Fax: updated information required E-mail: updated information required or teri @oxy genorchard. com (Mr. Joseph F. Jennings, President) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS WMI International, Inc. Mailing Address 2104 Brentwood Drive WMI International, Inc. Houston, TX 77019 P.O. Box 130583 Phone: updated information required Houston, TX 77219 Mobile: updated information required (Mr. Joseph F. Jennings, President) Fax: updated information required E-mail: updated information required or teri @ oxy genor chard. com (Mr. Joseph F. Jennings, President) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: WMI-2000 is non-flammable. 2. Ventilation: Avoid breathing dust or aerosol due to possibility of sensitization. Use adequate ventilation. 3. Skin and eye contact; protective clothing; treatment in case of contact: Minimize contact with eyes, skin, and clothing. Wash hands thoroughly after handling culture. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 45°F - 90°F Store in a cool, dry location. Keep partially-used containers tightly closed. Prolonged exposure Bioremediation Agents 2 WMI-2000 ------- to high temperature and humidity, may lower activity of product. 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE The shelf life of WMI-2000 is 2 years if stored at ambient temperatures VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: The culture should be activated for 2 hours in water, when applicable. Conditions for use vary depending on substrate concentration and type, pH, temperature, availability of nutrients, oxygen content, and liquid medium (static or flowing). 2. Concentration/Application Rate: Inoculation concentration is 5-9 billion spores per gram. 3. Conditions for Use: Temperature requirements are between 35°F and 100°F. The optimum dissolved oxygen content is 2 ppm at the sludge-to-water interface. Nitrogen and phosphorous are key nutrients which promote cultural growth, and should be maintained at concentrations of 15-20 ppm and 2.5-5 ppm, respectively. The optimum pH range is between 7.0 and 8.0. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 2626.7 0 1850.0 0 0 NUTRIENT 2763.3 0 2030.0 0 WMI-2000 2453.3 0 1880.0 0 CONTROL 2246.7 0 1823.3 0 7 NUTRIENT 1920.0 0 1666.7 0 WMI-2000 1243.3 0 1456.7 0 CONTROL 2240.0 14.7 1866.7 -0.9 28 NUTRIENT 1210.0 56.2 1480.0 27.0 WMI-2000 973.3 60.3 1253.0 33.3 Bioremediation Agents 3 WMI-2000 ------- Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product (WMI-2000) 0% 25% 44% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentage in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additives: Optimum pH: 7.0 Optimum temperature: 45°F - 90°F Optimum salinity: Fresh water to sea water 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 6.0 - 8.0 Temperature: 40°F - 120°F Salinity range: Fresh to sea water 4. Special nutrient requirements: None 5. Test results regarding the determination of the following: Salmonella - Negative Fecal Coliform - Negative Shigella - Negative Staphylococcus Coagulase positive - Negative Beta hemolytic Streptococcus - Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 4 WMI-2000 ------- TECHNICAL PRODUCT BULLETIN #B-36 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 17, 1991 REVISED LISTING DATE: OCTOBER 6, 1996 "OPPENHEIMER FORMULA" (aka, THE OPPENHEIMER FORMULA I, MICROSORB SC) I. NAME, BRAND, OR TRADEMARK OPPENHEIMER FORMULA (aka, THE OPPENHEIMER FORMULA I, MICROSORB SC) Type of Product: Biological Additive II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Oppenheimer Biotechnology, Inc. P.O. Box 1490 Pflugerville, TX 78691-1490 Phone: (512) 474-1016 E-mail: ien.neve@obio.com Website: www.obio.com (Ms. Jen Neve) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Oppenheimer Biotechnology, Inc. P.O. Box 1490 Pflugerville, TX 78691-1490 Phone: (512) 474-1016 E-mail: ien.neve@obio.com Website: www.obio.com (Ms. Jen Neve) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Special ventilation is not required. Treat product as an hygroscopic powder. In closed spaces use dust protective measures. 3. Skin and eye contact; protective clothing; treatment in case of contact: The application of the dry powder requires the usual precautions of a dust irritant to membranes. The material is easily removed by washing or flushing, and in confined areas or use, a protective mask and eye glasses are recommended. 4.a. Maximum storage temperature: 130°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 82°F V. SHELF LIFE The shelf life of the product is approximately 5 year. Bioremediation Agents 5 OPPENHEIMER FORMULA ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Optimal application is by powder seeding directly at the source of oil contamination. Application over larger areas of water surface can be accomplished by aerial powder dusting, spraying a water mixture of nutrients/formula over the oil area, or by dusting with mechanical powder pumps. 2. Concentration/Application Rate: The application rate at the source oil slick is 1 pound per cubic yard of oil. In the open sea slick, the basic application rate is 10 pounds per acre, but this may vary in different situations related to speed of clean up. In estuaries, a larger biomass is recommended and may be at a rate of up to 100 pounds per acre, depending on the oil type and concentration. Heavier oils may require a higher biomass than light oils. 3. Conditions for Use: THE OPPENHEIMER FORMULA may be used in a wide range of environmental conditions of temperature and salinities, ranging from fresh to 100 ppt salts. The formula is especially valuable in grass flats, marshes and the open sea. It has also proved effective in soil and fresh water oil clean up and municipal waste treatment, septic tanks and grease traps. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 DAYS AROMATIC 28 DAYS (ppm) S (ppm) CONTROL 29965.2 0 5620.5 0 0 NUTRIENT 31494.8 0 6660.2 0 OPPENHEIMER 31140.6 0 5528.2 0 CONTROL 30101.5 0 5610.1 0 7 NUTRIENT 8073.9 0 5086.6 0 OPPENHEIMER 5019.7 0 4338.9 0 CONTROL 28785.6 3.9 5512.7 1.9 28 NUTRIENT 706.2 97.8 4863.7 27.0 OPPENHEIMER 3396.8 89.1 3417.8 38.2 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product (Oppenheimer) -6.4% 50.9% 10.4% Bioremediation Agents 6 OPPENHEIMER FORMULA ------- b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentage in the composition: Natural, ubiquitous, hydrocarbon-oxidizing, microorganisms for use in removing hydrocarbons and organic materials from soils, fresh and salt waters by natural oxidative pathways. 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 7.6 Temperature: 82°F Salinity: Fresh water to 20 percent salts Optimal: 0.5 to 3.5% 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 5.5-11 Temperature: 32°F-140°F Salinity: Fresh to 15% 4. Special nutrient requirements: NA 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: <90/100 ml Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS OF HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 7 OPPENHEIMER FORMULA ------- TECHNICAL PRODUCT BULLETIN #B-41 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: DECEMBER 18, 1991 REVISED LISTING DATE: JANUARY 21, 1997 "MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL" I. NAME, BRAND, OR TRADEMARK MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL Type of Product: Biological Additive II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Verde Environmental, Inc. 9223 Eastex Freeway Houston, TX 77093 Phone: (713) 691-6468 (800)626-6598 Fax: (713)691-2331 Website: www.micro-blaze.com E-mail: bscogin@micro-blaze.com (Mr. William L. Scogin) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Verde Environmental, Inc. 9223 Eastex Freeway Houston, TX 77093 Phone: (713) 691-6468 (800)626-6598 Fax: (713)691-2331 Website: www.micro-blaze.com E-mail: bscogin@micro-blaze.com (Mr. William L. Scogin) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal room ventilation 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye contact. Wear protective gloves, and wash hands with soap and water after handling the product. Wash contaminated clothing and footwear before reuse. 4. Optimum Storage Conditions: 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage range temperature: NA 4.d. Temperatures of phase separations and chemical changes: NA Bioremediation Agents 8 MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL ------- V. SHELF LIFE Minimum 10 years, with proper storage, in original containers. Freezing will not kill these microbes; however, extreme heat (over 180°F) for long periods of time will kill the microbes. VI. RECOMMENDED APPLICATION PROCEDURE MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL is a liquid formulation of several microbial strains, surfactants, and nutrients designed to bioremediate organics and hydrocarbons in soil and water as well as control odors. 1. Application Method: Use normal spray equipment, fire or response equipment, eductor setups, water trucks, etc. as methods of application. Mix MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL/water mixture with contaminated soils and liquids thoroughly for maximum contact. Pick up treated contamination after volatile hazard has been negated per local regulatory parameters. For general bioremediation: For in-situ soils, mix MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL/water mixture can be tilled into the contaminated area. For shallower contamination, areas can be over sprayed with normal spray equipment, eductor setups, water trucks, etc. For deeper contamination, application can be applied through underground setups using perforated piping per regulatory recommendations. For wastewater and other operational by-product sludges and soils extracted from contaminated areas, a bioslurry or bioreactor can be setup using MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL and water in the process. 2. Concentration/Application Rate: For more viscous or less hazardous contamination, apply MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL at a 3% solution mixed with water (3 parts MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL, 97 parts water). When bioremediating soils, generally, per every 10 cubic yards of contaminated soils, use one gallon of concentrate, diluted with water according to contamination type. 3. Conditions for Use: Water Salinity: Can be mixed with any fresh, brackish or brine. However, brine reduces the effectiveness by 10%. Water Temperature: 35°F - 180°F pH: 4 to 11.5 Temperature: 32°F - 120°F Nutrient Requirements: Nutrients for microbes are included in product. However, for longer- term bioremediation projects, additional applications of bio-catalyst may be added to boost microbial activity. Type and Ages of Pollutants: For use on organics and hydrocarbon-based materials. These strains of bacteria provide the capability of biodegrading various straight chained, branched chained, aromatic and polynuclear aromatic hydrocarbons found in diesel and other fuels. Age of contamination is not a factor as much as its density. Tar-like substances may need to be cut for timely remediation. Bioremediation Agents 9 MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL ------- VII. TOXICITY AND EFFECTIVENESS Non-toxic, naturally-occurring spore-forming microorganisms common to soil and water. Non- pathogenic, certified by count; will not mutate. a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300,900) Federal Register September 15, 1994. Microbiological Results - Average Day 0 - 1.7 x 109 Day 7 - 8.43 x 108 Day 28 - 5.2xl07 The organisms in this product convert to a spore state (dormant) to survive an unfavorable environment and will reactivate upon favorable conditions. Documentation available from Verde Environmental. Summary Data Table DAYS 28 PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REP/PROD ALKANES 28 DAYS AROMATIC 28 DAYS (ppm) S (ppm) CONTROL 31258.6 0 973 0 NUTRIENT 28251.8 0 976.6 0 PRODUCT 29548.9 0 1081.2 0 CONTROL 31401.73 0 990.5 0 NUTRIENT 20728.3 26.6 619.1 36.6 PRODUCT 12870.5 56.4 496.3 54.1 CONTROL 32465.8 0 925.7 0 NUTRIENT 1787.2 93.7 722.6 26.0 PRODUCT 1758.2 94.1 566.9 47.6 Alkanes showed significant reductions with aromatic components less dramatic but still significant. Results of Gravimetric Analysis: Percentage ^ Control o) Decrease in Weight of Oil on Day 28 Nutrient Product (MICRO-BLAZE®^ 12% <1% 17.6% CONCLUSIONS: The MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL product shows an initial rapid consumption of all measured hydrocarbons at seven (7) days. This rate apparently slows over 28-day period in a closed environment which may be due to a change in the environment of the flask due to the rapid degradation rates. Because of the high microbial population at the end of the test, it is to be assumed that the quantity of metabolites might account for the increased weight as determined by the gravimetric analysis. Bioremediation Agents 10 MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL ------- b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentage in the composition: CONFIDENTIAL 2. Optimum pH, temperature, salinity ranges for use of the additive: pH: 7.5 Temperature: 45°F - 105°F Salinity: 0-10% 3. Minimum and maximum pH, temperature, salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: <5.9, >9.0 Temperature: <32°F, >180°F Salinity: <0%, 10% 4. Special nutrient requirements: None 5. Test results regarding the determination of the presence of the following: Product is determined to be free of gram negative contamination. Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS OF HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 11 MICRO-BLAZE® EMERGENCY LIQUID SPILL CONTROL ------- TECHNICAL PRODUCT BULLETIN #B-42 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JANUARY 3, 1992 REVISED LISTING DATE: FEBRUARY 5, 1997 UPDATED LISTING LETTER: OCTOBER 7, 2020 "VB591™, VB997™, BINUTRIX®" I. NAME, BRAND, OR TRADEMARK VB591™, VB997™, BINUTRIX® Type of Product: Biological Additive (patented, partial encapsulated oleophilic (oil-loving) nutrient; a nutrient additive that contains no microorganisms) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT BioNutraTech Inc. 13647 Pemberwick Park Lane Houston, TX 77070 Phone: (800) 567-5432 Phone: (281)354-5900 E-mail: shruza@bionutratech.com Website: www.bionutratech.com (Ms. Sandra L. Hruza) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS BioNutraTech Inc. 13647 Pemberwick Park Lane Houston, TX 77070 Phone: (800) 567-5432 Phone: (281)354-5900 E-mail: shruza@bionutratech.com Website: www.bionutratech.com (Ms. Sandra L. Hruza) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal ventilation is adequate. 3. Skin and eye contact; protective clothing; treatment in case of contact: Normal precautions and protective equipment for handling any type of powder, such as dust protectors and eye shield. Avoid contact with eyes and do not take internally. Upon contact with eyes, flush with water immediately for a minimum of 15 minutes. If redness or irritation continues, contact a physician. Avoid breathing dust. 4.a. Maximum storage temperature: >140°F 4.b. Minimum storage temperature: NA 4.c. Optimum storage temperature range: 50°F to 80°F 4.d. Temperature phase separations and chemical changes: NA Bioremediation Agents 12 VB591™, VB997™, BINUTRIX® ------- V. SHELF LIFE The shelf life is approximately three years if kept dry. Store in dry location and avoid contact with moisture. Prolonged storage may result in the formation of soft clumps, which are easily broken by mechanical disruption. VI. RECOMMENDED APPLICATION PROCEDURE VB591™, VB997™, BINUTRIX® is a powder, and can be applied using conventional powder spraying equipment. No pre-mixing or dilution is required. 1. Application Method: Application for localized spills can be done using hand-held pressurized dust blowers. For inland waterways, ship channels, marinas or coastal wetlands, large dust blowers mounted on barges or ships can be employed to apply the product. Application by aircraft using conventional dust spraying systems is recommended for treatment of large uncontained spreading spills or spills in open waters or at sea. 2. Concentration/Application Rate: Recommended initial application rate is 5 to 15 pounds of VB591™, VB997™, BINUTRIX® per barrel of spilled oil. Follow-up applications at 48 to 72 hour intervals should be adjusted to allow for reduction in oil due to clean-up activities and natural loss by evaporation, droplet formation and dispersion and microbial activity. Applications should not exceed 250 pounds per acre per application. 3. Conditions for Use: VB591™, VB997™, BINUTRIX® should be applied to spilled oil as soon as possible following spillage to stimulate natural oil utilizing microbial populations to maximize biodegradation activity. Application of VB591™, VB997™, BINUTRIX® to spilled oil does not significantly alter the physical consistency of the spilled oil, and as such will not adversely affect conventional cleanup activities, nor will conventional and removal activities adversely affect the activity of VB591™, VB997™, BINUTRIX®. Dispose of waste in accordance with local, state, and federal regulations. Information regarding use of VB591™, VB997™, BINUTRIX® in conjunction with chemical dispersing agents is at present not available. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 31041.7 0 973.1 0 0 NUTRIENT 28251.8 0 976.6 0 VB591™, VB997™, BINUTRIX® 28813.8 0 932.8 0 Bioremediation Agents 13 VB591™, VB997™, BINUTRIX® ------- CONTROL 31436.33 0 990.5 0 7 NUTRIENT 20728.3 26.6 619.1 36.6 VB591™, VB997™, BINUTRIX® 14637.4 49.2 733.1 21.4 CONTROL 32465.8 0 925.7 0 28 NUTRIENT 1787.2 93.7 722.6 26.0 VB591™, VB997™, BINUTRIX® 937.97 96.8 290.8 73.1 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product <1% 17.6% 18.0% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS VB591™, VB997™, BINUTRIX® is an oleophilic nutrient additive and contains no preserved natural or mutated microorganisms of any type. 1. Listing of all microorganisms by species and percentage in the composition: None 2. Optimum pH, temperature, and salinity ranges for use of the additive: VB591™, VB997™, BINUTRIX® may be used under any conditions where natural populations of oil-degrading microbes are active. 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: NA Temperature: NA Salinity: NA 4. Special nutrient requirements: None 5. Test results regarding the determination of the presence of the following: Salmonella: NA Fecal coliform: NA Shigella: NA Staphylococcus coagulase positive: NA Beta hemolytic Streptococci: NA IX. PHYSICAL PROPERTIES NA Bioremediation Agents 14 VB591™, VB997™, BINUTRIX® ------- X. ANALYSIS OF HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 15 VB591™, VB997™, BINUTRIX® ------- LISTING CHANGES PENDING; VERIFICATION BY MANUFACTURER AND EPA REQUIRED TECHNICAL PRODUCT BULLETIN #B-43 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 12, 1992 REVISED LISTING DATE: MARCH 21, 1997 "STEP ONE" (aka, B&S INDUSTRIAL) I. NAME, BRAND, OR TRADEMARK STEP ONE (aka, B&S INDUSTRIAL) Type of Product: Biological Additive II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT B&S Research, Inc. 4345 Highway 21 Embarrass, MN 55732 Phone: (218) 984-3757 Fax: (218) 984-3212 E-mail: farmforprofit@frontier.com (Mr. H. W. Lashmett) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS B&S Research, Inc. Bioremediation International 4345 Highway 21 4345 Highway 21 Embarrass, MN 55732 Embarrass, MN 55732 Phone: (218) 984-3757 Phone: (218) 984-3757 Fax: (218) 984-3212 Fax: (218) 984-3212 E-mail: farmforprofit@frontier.com E-mail: farmforprofit@frontier.com (Mr. H. W. Lashmett) (Mr. H. W. Lashmett) Farm for Profit Research and Development 4345 Highway 21 Embarrass, MN 55732 Phone: (800) 232-7692 Fax: (218) 984-3212 E-mail: farmforprofit@frontier.com (Mr. H. W. Lashmett) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: None 2. Ventilation: Normal ventilation is adequate 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with Bioremediation Agents 16 STEP-ONE ------- skin, especially when there are open wounds. In case of skin contact, wash with soapy water. The use of protective gloves is recommended. Avoid contact with eyes. In case of eye contact, immediately flush eyes with plenty of water continuously for at least 15 minutes. Consult a physician. The use of protective goggles is recommended. Avoid inhalation and ingestion. It is recommended that workers wear dust mask and not eat or smoke while handling the product(s). 4.a. Maximum storage temperature: 90°F 4.b. Minimum storage temperature: -30°F 4.c. Optimum storage temperature range: 32°F to 70°F 4.d. Temperature phase separations and chemical changes: NA V. SHELF LIFE Over 3 years VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Components of the product STEP ONE (BC101) and STEP ONE (MSE2.5) are only sold together. B&S Research will make application recommendations based on contamination and ppm of contamination at time of purchase order and employ specified application methods (spray, plowing, agitation, etc.) appropriate for a particular situation. 2. Concentration/Application Rate: Nominally, the STEP ONE water mixture can be used on most hydrocarbons, including crude and refined petroleum products, pesticides, etc., on land, fresh water or ocean water. Laboratory tests also indicate effectiveness in destruction of PCB's. In certain circumstances, B&S Research, Inc. may require laboratory soil and water contamination tests before the product may be used (see VI1. above). VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED % TOTAL MEAN RED % MEAN 3 REPS/PROD. ALKANES 28 DAYS AROMATIC S 28 DAYS (ppm) (ppm) 0 CONTROL 29959.5 5391.8 NUTRIENT 29008.5 5163.0 STEP ONE 30477.8 5499.8 7 CONTROL 33471.3 5720.9 NUTRIENT 22723.7 5050.1 STEP ONE 24196.8 3110.2 28 CONTROL 30997.4 0.0 % 5388.9 0.0 % NUTRIENT 1103.9 96.19% 4582.4 11.23% Bioremediation Agents 17 STEP-ONE ------- DAYS PRODUCT TOTAL MEAN RED % TOTAL MEAN RED % 3 REPS/PROD. ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS STEP ONE 17059.4 44.03% 2501.9 54.51% Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product (STEP ONE) 0% 19% 51% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 6-8 Temperature: 70°F to 90°F Salinity: Fresh or salt (ocean <110 ppm) water, land or dry surfaces 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: <5 or <9, (apply neutralizing agents — lime or P205 Temperature: <50°F or>135°F Salinity: <0 or >110 ppm 4. Special nutrient requirements: None 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: -7°F 3. Viscosity: 2.8 cSt @ 50°F 3.5 cSt @ 32°F 5.9 cSt @ -4°F 4. Specific Gravity: 1.03 @ 59°F 5. pH: 7.2 (1:2.5:80 BC101:MSE2.5:water mixture) 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: Noedal 8. Solvents: None Bioremediation Agents 18 STEP-ONE ------- 9. Additives: Phosphoric acid as P205 3% emulsifier <.5% by weight 10. Solubility: Infinite X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration Arsenic <0.0200 Cadmium <0.0030 Chromium 0.0859 Copper 0.0177 Lead 0.0090 Mercury 0.0002 Nickel <0.0080 Zinc 0.0602 Cyanide 0.2830 Chlorinated Hydrocarbons <0.0050 Bioremediation Agents 19 STEP-ONE ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 8/09/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #B-45 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JANUARY 28, 1993 REVISED LISTING DATE: NOVEMBER 14, 1995 "SYSTEM E.T. 20" I. NAME, BRAND, OR TRADEMARK SYSTEM E.T. 20 Type of Product: Biological Additive (formerly MCW.B 20) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Environmental Restoration Services 9211 Lakewood Drive Windsor, CA 95492 E-mail: ERS,BTI@gmail.com Phone: (619) 253-0664 (Mr. John Chase) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Environmental Restoration Services 14384 Highland Valley Road Escondido, CA 92025 E-mail: ERS,BTI@gmail.com Phone: (619) 253-0664 (Mr. John Chase) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: SYSTEM E. T. 20 is non-flammable 2. Ventilation: No special ventilation is required under normal use. 3. Skin and eye contact; protective clothing; treatment in case of contact: In its primary form, no special handling or storage is required. Avoid excessive inhalation, and protect the nose and mouth with a dust protection mask. Wear protective gloves, and wash hands with soap and water after handling the product. 4.a. Maximum storage temperature: 4.b. Minimum storage temperature: 4.c. Optimum storage temperature range: 4°C - 20°C (39°F - 68°F). Place in a dry area, shaded from sunlight. 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE 2 years if maintained at 4°C (39°F). Bioremediation Agents 20 SYSTEM E.T. 20 ------- VI. RECOMMENDED APPLICATION PROCEDURE SYSTEM E. T. 20 can be used on a broad range of hydrocarbon compounds (including PAH's) found in open and closed water systems (salt or fresh) or in soil (beach, sands, or inland soil types). SYSTEM E.T. 20 protocols can be used with indigenous and introduced bacteria. SYSTEM E.T. 20 is an oleophilic, non-water soluble nutrient, which releases nitrogen and phosphorous enzymatically, thus allowing SYSTEM E.T. 20 to be used in water and soil applications including: conditions requiring fast degradation rates due to regulations, limited space or cost; under conditions where weathered or heavy oils, sludges or PAH's exist that require consistently high populations of hydrocarbon degrading bacteria to metabolize these long or more complex carbon chains; tropical or sub-tropical conditions that support large, indigenous, non-beneficial bacterial populations that would otherwise dilute the effectiveness of standard bioaugmentation approaches; aqueous conditions in which soluble or time release nutrient compounds would be washed away or diluted, i.e., beaches, frequent rains, floods, streams, stream banks, estuaries and areas affected by tides; sensitive environmental conditions that demand low or no toxicity; toxicity in soil or water during bioremediation may be stimulated by adding broadly available nutrients which may activate disease carrying bacilli or pathogens; controlled nutrient release to SYSTEM E. T. 20 bacteria prevents over-nitrification; conditions requiring the elimination of oil discoloration caused by the presence of polar fractions; and conditions where salt water conditions exist or where only salt water is available for bacteria application. 1. Application Methods: Biopile Land farm Pump and Treat Bioreactor Bio slurry In situ Windrow Topical application to discolored rocks or soil. Topical application to beaches. 2. Concentration/Application Rate: Concentration and rate of application will vary from site to site depending upon the type of contaminant and the area contaminated. Contact QET for specific information. 3. Conditions for Use: Before applying SYSTEM E. T. 20, QET recommends that the site be evaluated for its physical and chemical soil characteristics (i.e., pH, salinity, conductivity, physical parameters, moisture content, hydrocarbon type and concentration, nitrogen content, etc.), and toxicity of both the soil and the contaminant, by biological screening tests. Basic biological requirements of SYSTEM E. T. 20, site conditions and SYSTEM E. T. 20 capabilities dictate the appropriate procedures for application of SYSTEM E. T. 20. Biological requirements for SYSTEM E. T. 20 bacteria are nutrients, adequate oxygen supply, hydrocarbon food source, neutral pH and a 15% minimum moisture level for soil remediation applications. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table Bioremediation Agents 21 SYSTEM E.T. 20 ------- DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 DAYS AROMATIC 28 DAYS (ppm) S (ppm) CONTROL 29959.5 0 5391.8 0 0 NUTRIENT 29008.5 0 5163.0 0 SYSTEM E.T. 20 30476.1 0 5311.3 0 CONTROL 33471.3 0 5720.9 0 7 NUTRIENT 22723.7 0 5050.1 0 SYSTEM E.T. 20 3837.1 0 2928.8 0 CONTROL 30997.4 0 5383.9 0.2 28 NUTRIENT 1103.9 96.2 4582.4 11.2 SYSTEM E.T. 20 261.9 99.1 1188.0 77.0 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product (SYSTEM E.T. 20) 0% 19% 18% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentage in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 7.5, (6.5 to 8.5) Temperature: 4°C to 35°C (39°F to 95°F) Salinity: Fresh to 2.5% (average ocean salt level) 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: <6.5 and >8.5 Temperature: <5°C and >35°C (<41°F and >95°F) Salinity: >3% 4. Special nutrient requirements: Recommendation is for a non-soluble nutrient. The specific types of nutrients will be dependent on the site requirements. 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Bioremediation Agents 22 SYSTEM E.T. 20 ------- Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS OF HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 23 SYSTEM E.T. 20 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 5/18/2006 7/27/2022 TECHNICAL PRODUCT BULLETIN #B-48 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 10, 1993 REVISED LISTING DATE: AUGUST 31, 2000 "BET BIOPETRO" I. NAME, BRAND, OR TRADEMARK BET BIOPETRO Type of Product: Biological Additive (formerly BET BIOPETRO HEAVY) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT BioEnviroTech ADDRESS: updated information required PHONE: updated information required (Mr. Warren Butler) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS BioEnviroTech ADDRESS: updated information required PHONE: updated information required (Mr. Warren Butler) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-Flammable 2. Ventilation: Normal ventilation 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye and skin contact. In case of eye contact, flush eyes with water or eyewash, and refrain from rubbing. For skin contact, wash with mild soap and apply hand cream if itching or redness occurs. Avoid inhalation. In case of inhalation, seek fresh air. Repeated inhalation has been associated with respiratory allergy in some persons. Such allergic individuals should wear protective clothing and eye goggles. In enclosed buildings, workers should wear single use nuisance dust masks appropriate for fine particulate dust. In outdoor field applications, no dust mask is required. 4.a. Maximum storage temperature: 105°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 50°F to 75°F 4.d. Temperatures of phase separations and chemical changes: NA Bioremediation Agents 24 BET BIOPETRO ------- V. SHELF LIFE More than 3 years in unopened original shipping container, stored in cool dry area. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: BET BIOPETRO is a powder containing granules of bacterial product formulated to provide performance in the bioremediation of heavy refined and crude hydrocarbon contaminants in both soil and water environments. Application procedure and treatment schedule will vary with specific environmental conditions and bioremediation requirements. Contact BET for specific technical advice. 2. Concentration/Application Rate: Dosage will vary with specific environmental conditions and bioremediation requirements. Contact BET for specific technical advice. 3. Conditions for Use: BET BIOPETRO should be used at temperatures in the range of 45°F to 100°F, pH range of 5.5 to 8.5, and dissolved oxygen level of 3 to 5 mg/1. The product is effective in both salt and fresh waters. However, where extreme salinity is projected, testing and evaluation of the bacteria in bioremediation are advised. BET BIOPETRO cultures exhibit some resistance to toxic shocks from strong chemicals. Nonetheless, highly chlorinated compounds, acids, caustics, disinfectants, germicides, and chlorine will render the cultures ineffective, just like other bacteria. Where such chemicals are anticipated, testing and evaluation of the bacteria in bioremediation are advised. BET BIOPETRO cultures require supplemental nutrients for optimum performance (See section VIII. 4). VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 DAYS AROMATIC S 28 (ppm) (ppm) DAYS CONTROL 29965.2 0 5620.5 0 0 NUTRIENT 31494.8 0 6660.2 0 BET BIOPETRO 25914.5 0 5569.1 0 CONTROL 30101.5 0 5610.1 0 7 NUTRIENT 8073.9 0 5086.6 0 BET BIOPETRO 373.0 0 1220.0 0 CONTROL 28785.6 4.0 5512.7 2.0 NUTRIENT 706.2 98.0 4863.7 27.0 Bioremediation Agents 25 BET BIOPETRO ------- DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 DAYS AROMATIC S 28 28 (ppm) (ppm) DAYS BET BIOPETRO 350.3 99.0 1882.9 67.0 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product (BET BIOPETRO) 0% 51% 30% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentage in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive pH: 6.6 to 7.4 Temperature: 70°F to 95°F Salinity: Fresh to Salt water 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity. pH: <5.5 and >8.5 Temperature: <45°F and >105°F Salinity: Extreme salinity 4. Special nutrient requirements: BioEnviroTech, Inc. recommends nutrient supplements for optimum performance of the product in bioremediation application. The required nutrients are dependent upon hydrocarbon contamination levels. Contact BET for specific nutrient dosing requirements. 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS OF HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 26 BET BIOPETRO ------- TECHNICAL PRODUCT BULLETIN #B-53 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 26, 1996 REMOVAL DATE: AUGUST 16, 2005 RELISTING DATE: SEPTEMBER 18, 2009 "OIL SPILL EATER II (OSE II)" I. NAME, BRAND, OR TRADEMARK OIL SPILL EATER II (OSE II) Type of Product: Bioremediation Agent (Biological Enzyme Additive [previously listed as a Nutrient Additive]) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT OSEI Corporation (Formerly Sky Blue Chems) P.O. Box 515429 Dallas, TX 75251-5429 Phone: (972) 669-3390 E-mail: oseicorp@msn.com Website: www.osei.us (Mr. Steven Pedigo, Chairman, CEO, Inventor) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS OSEI Corporation (Formerly Sky Blue Chems) P.O. Box 515429 Dallas, TX 75251-5429 Phone: (972) 669-3390 E-mail: oseicorp@msn.com Website: www.osei.us (Mr. Steven Pedigo, Chairman, CEO, Inventor) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Water-based, non-flammable 2. Ventilation: Needs no ventilation; aqueous-based product; does not emit hazardous vapors 3. Skin and eye contact; protective clothing; treatment in case of contact: OSE II is not a primary dermal irritant. Avoid eye contact, and wear goggles if possible for the spray to come in direct contact with eyes. Facilities for quick and copious eye flushing should be provided and prompt medical attention should be sought if exposure and irritation persists. Protective rubber gloves are suggested during handling. Before mixing the product has a smell of fermentation. The product does not give off any harmful vapors. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: None; OSE II can freeze and thaw without adverse effects 4.c. Optimum storage temperature range: 72°F 4.d. Temperatures of phase separations and chemical changes: 120°F Bioremediation Agents 27 OIL SPILL EATER II (OSE II) ------- V. SHELF LIFE OSE II has a recommended shelf life of 5 years. After 5 years at optimum storage temperature, there is an approximate 10% decrease per year in product capability. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: A. Use surface spray apparatus, such as small hand held tanks, back pack, large mixing tanks with mechanical pumping devices, vessels with booms for spraying wide paths, or spray devices on airplanes or helicopters. B. OSE II can be applied by eductor systems from vessels, fire trucks, etc. Set the eductor system to 2% and apply 1 gallon of mixed OSE II to each spilled gallon of hydrocarbon. 2. Concentration/Application Rate: General - OSE II generally takes 3 to 30 minutes to penetrate the molecular walls of hydrocarbons. However, once you spray OSE II on the hydrocarbons, OSE II attaches itself and will eventually engulf the hydrocarbons regardless of where the hydrocarbons may spread on the surface of salt or fresh water. Additionally, once you spray OSE II, the hydrocarbons cannot attach itself to the shoreline, rocks, or any equipment in its path. OSE II breaks down the adhesion properties of hydrocarbons and causes hydrocarbons to float, thereby, eliminating secondary contamination of the water column or any other areas, and holding the contaminated area to the water's surface, the original contaminated area. • If OSE II is to be used on ocean spills or on intertidal zones OSE II should be mixed with ocean water. • If OSE II is to be used on lakes, rivers, streams, ponds, or on land mix the product with water from a lake, stream, or pond. • If you are performing a cleanup, make sure the water used to mix with OSE II, and the water used to keep the area saturated, is the type of water normally associated with that area. • If you use fresh water in an area normally contacted with salt water or vice versa, the different types of bacteria and competition could occur, not to mention the problems with salinity for fresh water organisms. [Note: Do not mix tap water with OSE II if possible: Chlorine in tap water slows bacterial enhancement] Spills on Water: Dilute each gallon of OSE II with 50 gallons of fresh, brackish, or salt water - depending on the water associated with the area that has been impacted by the spill. Apply OSE II at a ratio of 1 gallon mixed OSE II to each gallon of hydrocarbon spilled. Apply using hand held sprayers, tank sprayers, booms from vessels, helicopters, or airplanes; by spraying the perimeter first then working toward the middle of the spilled area. Next spray the entire surface of the spill. If the spill is very heavy (more than 2 inches thick) it is recommended that OSE II be applied every day until you have met a 1:1 ratio of OSE II and water mixture to spilled oil/hydrocarbons. • Use 1 gallon OSE II for every 50 gallons of hydrocarbons. • Use 1 drum of OSE II for every 2,750 gallons of hydrocarbons. • If you know gallons of hydrocarbons spilled, multiply gallons of hydrocarbons by 0.02 to get amount of OSE II needed [gallons of hydrocarbons x 0.02 = gallons of OSE II], • If you know barrels of crude oil spilled, multiply barrels of crude oil by 0.015 toO get drums Bioremediation Agents 28 OIL SPILL EATER II (OSE II) ------- of OSEII needed [barrels of crude oil x 0.015 = drums of OSEII], • If you do not know gallons of hydrocarbons or barrels of crude oil, multiply size of spill by 0.0023 to get drums of OSE II needed or by 0.12 to get gallons of OSE II needed [(yards long x yards wide x inches thick) x 0.0.0023 = drums of OSE II or (yards long x yards wide x inches thick) x 0.015 = gallons of OSE II], Intertidal Zone: Mix each 55 gallon drum of OSE II with 2,750 gallons of fresh, brackish, or salt water. The water used is determined by the type of water associated with the site. OSE II should be applied as the tide recedes (if there is a tide) and once the tide comes in the application should cease until the tide recedes again. Additional applications should only be warranted if spill has been allowed time to percolate into the depths of the soil. If there is no tide, but waves have pushed the spill into the intertidal zone, then there will be direct access to the spill at all times. If possible use string or stakes to grid off the beach or intertidal zone area, and then you can calculate how much premixed OSE II to apply to a given area. If unable to grid off an area then calculate how much OSE II to apply and then determine how much premixed OSE II will flow through a nozzle (gallons per minute) then let application technician know how many gallons to apply in a given area and this can be determined by applying product for a certain time period to get the correct amount of OSE II applied to gain the 1:1 ratio. Note: If the intertidal zone is associated with the sea then mix OSE II with salt water. If the spill area is in an area of brackish water then mix OSE II with brackish water. If the intertidal zone is associated with fresh water such as lakes, rivers, streams, ponds, creeks, aquifers, or drinking water wells then use fresh water to mix OSE II. 3. Conditions for Use: • OSE II can remediate hydrocarbon-based material including chlorinated hydrocarbons, PCB's, dioxins, and some pesticides. • As the age of spilled hydrocarbons increases, the time necessary for bioremediation increases. In general, fresh crude, gasoline of BTEX takes from 72 hours to 30 days to completely bioremediate. • Variations of sea water salinity should have no effect, but as long as microbial life can exist, then OSE II will be effective. • OSE II bioremediation slows somewhat at temperatures below 40°F. OSE II however, will continue to work at any liquid water temperature that will sustain microbial life. Bioremediation Agents 29 OIL SPILL EATER II (OSE II) ------- VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 43,170 - 11,435 - 0 NUTRIENT 40,569 - 11,785 - OSE II 41,730 - 12,155 - CONTROL 39,250 9.1 10,355 9.4 7 NUTRIENT 34,815 14.2 9,898 16.0 OSE II 26,316 36.9 8,072 33.6 CONTROL 35,797 17.1 9,534 16.6 28 NUTRIENT 26,507 34.7 8,938 24.2 OSE II 4,273 89.8 1,268 89.6 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 16.5% 52.0% 85.4% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of each component of the total formulation, other than enzymes, by chemical name and percentage by weight: CONFIDENTIAL 2. Enzyme Names: CONFIDENTIAL 3. I.U.B.: CONFIDENTIAL 4. Source of Enzymes: Fermentation process 5. Units: No less than 1% and no more than 50% by weight 6. Specific Gravity: 1.05 7. Optimum Conditions: a. pH: 7.0 b. Temperature: 72°F c. Salinity Ranges: Fresh water to salt water d. Maximum and Minimum pH: 3.5-8.0 e. Maximum and Minimum Temperature: 28°F - 128°F Bioremediation Agents 30 OIL SPILL EATER II (OSE II) ------- f. Maximum and Minimum Salinity Levels - Salinity level above that will support microbial activity will adversely affect OSE II's performance g. Enzyme Shelf Life: Up to 5 years when properly stored h. Enzyme Optimal Storage Conditions: 72°F is optimal, enzyme range is freezing to 120°F, never leave OSE II in direct sunlight for more than a couple of hours IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 31 OIL SPILL EATER II (OSE II) ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN B-55 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: SEPTEMBER 10, 1999 "LAND AND SEA RESTORATION PRODUCT 001 (VELITE)" I. NAME, BRAND, OR TRADEMARK LAND AND SEA RESTORATION PRODUCT 001 (VELITE) Type of Product: Bioremediation Agent (Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Land and Sea Restoration LLC ADDRESS: updated information required PHONE: updated information required (Mr. T. Shawn Parker) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Land and Sea Restoration LLC ADDRESS: updated information required PHONE: updated information required (Mr. T. Shawn Parker) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Flash Point 250°C (482°F) 2. Ventilation: Normal ventilation 3. Skin and eye contact; protective clothing; treatment in case of contact: Protective clothing and glasses. In case of eye contact, flush eyes with water or eyewash and refrain from rubbing. For skin contact, wash with mild soap and apply cream if itching or redness occurs. Avoid inhalation. In case of inhalation, seek fresh air. Wear protective clothing and eye goggles. Workers should wear single use nuisance dust masks appropriate for fine particulate dust. 4.a. Maximum storage temperature: 65°C (150°F) 4.b. Minimum storage temperature: 0°C (32°F) 4.c. Optimum storage temperature range: 0°C to 65°C (32 to 150°F) 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE More than 5 years in unopened original shipping container, store in a cool, dry place. Avoid moisture prior to use. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: On water, spread over contaminated area at 1 to 3 ratios. On soil, blend to depth equivalent to contamination level. On hard surfaces, spread over contaminated area. 4/02/2007 7/27/2022 Bioremediation Agents 32 LAND AND SEA RESTORATION PRODUCT 001 (VELITE) ------- Make sure the spill is completely absorbed. For best results agitate with broom. (Will not damage cured asphalt if used as an absorbent for spills.) Remove and dispose of in accordance with all state and federal laws, after absorption is complete. 2. Concentration/Application Rate: 1 part 001 to 3 parts hydrocarbon. 3. Conditions for Use: NA VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 13.8239 0 0.0443 0 0 001 13.5856 0 0.0509 0 CONTROL 14.3292 0 0.0473 0 7 001 10.1005 29.52 0.0437 0 CONTROL 14.4675 0 0.0401 0 28 001 8.2629 42.92 0.0273 31.92 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Product (001) 0% 25.18% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 6 to 8 Temperature: 25°C to 30°C (77°F to 86°F) Salinity: Fresh to salt water Bioremediation Agents 33 LAND AND SEA RESTORATION PRODUCT 001 (VELITE) ------- 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: NA Temperature: NA Salinity: NA 4. Special nutrient requirements: The product "001" is a nutrient, therefore no nutrients are required. 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: <3 Shigella: Negative Staphylococcus Coagulase positive: <10 Beta hemolytic Streptococci: 1,100 IX. PHYSICAL PROPERTIES 1. Flash Point: 250°C (482°F) 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: NA 5. pH: NA 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: NA 9. Solubility in Water: NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 34 LAND AND SEA RESTORATION PRODUCT 001 (VELITE) ------- TECHNICAL PRODUCT BULLETIN B-56 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JULY 24, 2002 "S-200C" I. NAME, BRAND, OR TRADEMARK S-200C Type of Product: Bioremediation Agent (Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT RBL Environmental, LLC* 1311 Dorothy Avenue Phoenixville, PA 19460 Phone: (610) 520-7665 E-mail: iim.lynn@iepusa.com (Mr. James Lynn) (*RBL Environmental, LLC is the manufacturer and marketer for International Environmental Products) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS RBL Environmental, LLC 1311 Dorothy Avenue Phoenixville, PA 19460 Phone: (610) 520-7665 E-mail: iim.lynn@iepusa.com (Mr. James Lynn) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Ventilation of the work place is not necessary. 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of contact with skin or eyes, wash with plenty of water. 4.a. Maximum storage temperature: 132°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 55°F - 85°F 4.d. Temperatures of phase separations and chemical changes: <32°F and >140°F V. SHELF LIFE The recommended shelf life of S-200C is 10 years if kept in the unopened, original container. Bioremediation Agents 35 S-200C ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: S-200C is a light amber liquid, and as such can be sprayed with traditional liquid spraying equipment, such as pressurized sprayers or backpack sprayers. 2. Concentration/Application Rate: The recommended application rate is approximately 10% by of the S-200C as compared to the hydrocarbon being remediated. In other words, use 1 pound of S-200C for every 10 pounds of hydrocarbon you are remediating. For applications on soil contaminated below 1 foot, the soil is turned and the material is applied. This allows air to circulate and thereby maintains an aerobic condition. On a surface application, the amount to use is approximately 0.1 to 1 pound of S-200C for every square yard of surface area. The amount sprayed is dependent on the amount of hydrocarbon on the surface you are spraying. To remediate a sheen on water, the same application ratio for a surface application is used. 3. Conditions for Use: S-200C is a bioremediation accelerator used for the remediation of hydrocarbon spills or leaks. It is a non-intrusive, cost effective remedy for the cleanup of these hydrocarbons. These hydrocarbons include but are not limited to gasoline, No. 2 up to No. 6 diesel fuel, jet fuels, kerosene, lubricating oils, hydraulic oils, and crude oils. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 27666 0 5600 0 0 S-200C 29333 0 5666 0 CONTROL 21333 0 4333 0 7 S-200C 11000 0 4400 0 CONTROL 18771 32 5597 0.05 28 S-200C 660 98 5073 10.4 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Product (001) -18.57% 27.82% Bioremediation Agents 36 S-200C ------- b. Toxicity: Material Tested S-200C Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Mysidopsis bahia Species LC50 (ppm) 39.69 96-hr 21.33 48-hr 35.36 96-hr 35.36 48-hr 25.33 96-hr 17.67 48-hr 22.96 48-hr No. 2 Fuel Oil S-200C & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: S-200C is a nutrient bioremediation accelerator and does not contain bacterial cultures or amendments. However, with the addition of S-200C, the microbiological data shows a continued viability of microbial incubations over time. 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 7.0 Temperature: 86°F Salinity: Fresh to salt water 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 4.5 - 10.0 Temperature: 50°F - 120°F Salinity: 0% - 10% 4. Special nutrient requirements: NA 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: 40°F 3. Viscosity: 100cp@70°F 4. Specific Gravity: 0.996 5. pH: 4.5 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: NA 9. Solubility in Water: Dispersible Bioremediation Agents 37 S-200C ------- X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS S-200C does not contain any heavy metals, cyanide, or chlorinated hydrocarbons. Bioremediation Agents 38 S-200C ------- TECHNICAL PRODUCT BULLETIN B-57 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JANUARY 8, 2007 "SPILLREMED (MARINE)®" (aka, AGROREMED, HYDROREMED, SPILLREMED (INDUSTRIAL), VAPORREMED) I. NAME, BRAND, OR TRADEMARK SPILLREMED (MARINE)® (aka, AGROREMED, HYDROREMED, SPILLREMED (INDUSTRIAL), VAPORREMED) Type of Product: Bioremediation Agent (Biological Additive: Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Sarva Bio Remed, LLC 25 Marianne Drive, Suite 'B' York, PA 17406 Phone: (717) 779-0040 Phone: (877) 717-2782 E-mail: sales@sarvabioremed.com Website: www.sarvabioremed.com (Mr. Satya Ganti) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Sarva Bio Remed, LLC 25 Marianne Drive, Suite 'B' York, PA 17406 Phone: (717) 779-0040 Phone : (877) 717-2782 E-mail: sales@sarvabioremed.com Website: www.sarvabioremed.com (Mr. Satya Ganti) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: No special ventilation required. 3. Skin and eye contact; protective clothing; treatment in case of contact: On contact with product, wash with plenty of water and for eye contact consult your physician. Use of gloves and eye protection is recommended during field application to protect eyes from spray. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: Ambient 4.d. Temperatures of phase separations and chemical changes: <32°F and >100°F Bioremediation Agents 39 SPILLREMED (MARINE)® ------- V. SHELF LIFE The recommended shelf life is one year. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: SPILLREMED (MARINE)® is a ready to use liquid product. It can be sprayed undiluted over the spill in open water conditions. 2. Concentration/Application Rate: SPILLREMED (MARINE)® is applied in a product to oil ratio of 1:10. Rate of application is one gallon per 10 minutes. 3. Conditions for Use: SPILLREMED (MARINE)® is a marine salt formulation and is not effective in fresh water conditions. Optimal effectiveness is in the salinity range of 10 to 35 ppt. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 48,963.31 13,467.59 0 NUTRIENT SPILLREMED (MARINE)® CONTROL 46,963.33 52,063.18 47,606.78 13,779.24 14,143.06 11,262.98 7 NUTRIENT SPILLREMED (MARINE)® 40,853.28 43,236.67 11,329.01 11,076.99 CONTROL 45,467.28 7 12,560.37 7 28 NUTRIENT 7,210.06 98 9,927.87 28 SPILLREMED (MARINE)® 1,310.09 97 7,442.71 47 Bioremediation Agents 40 SPILLREMED (MARINE)® ------- Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control 6.00% Nutrient 76% Product 85% b. Toxicity: Material Tested SPILLREMED (MARINE)® Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 392.30 96-hr 343.80 48-hr 40.50 96-hr 17.40 48-hr 37.50 96-hr 22.40 48-hr 8.00 96-hr 15.90 48-hr No. 2 Fuel Oil SPILLREMED (MARINE)® & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 7.6 Temperature: 55°F Salinity: 30 ppt 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 6.5-6.9 Temperature: 40°F - 90°F Salinity: 10 ppt - 35 ppt 4. Special nutrient requirements: None 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 41 SPILLREMED (MARINE)® ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 3/22/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN B-58 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: DECEMBER 3, 2007 "JE1058BS" I. NAME, BRAND, OR TRADEMARK JE1058BS Type of Product: Bioremediation Agent (Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Japan Energy Corporation Business Development Department, Bio Research Center 3-17-35 Niizo-Minami Toda-shi, Saitama 335-8502 Japan Phone: updated information required Fax: updated information required E-mail: updated information required (Hisashi Saeki) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Japan Energy Corporation Business Development Department, Bio Research Center 3-17-35 Niizo-Minami Toda-shi, Saitama 335-8502 Japan Phone: updated information required Fax: updated information required E-mail: updated information required (Hisashi Saeki) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Use adequate ventilation. Treat product as a hygroscopic powder. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with eyes and do not take internally. Upon contact with eyes, flush with plenty of fresh water. Avoid breathing dust. Normal protective equipment for handling of powder, such as a dust mask and eye shield can be used. 4.a. Maximum storage temperature: 105°F 4.b. Minimum storage temperature: NA 4.c. Optimum storage temperature range: 0°F - 68°F 4.d. Temperatures of phase separations and chemical changes: NA Bioremediation Agents 42 JE1058BS ------- V. SHELF LIFE The shelf life of the product is approximately 2 years if stored in a cool dry area. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: JE1058BS contains biosurfactant and has an ability to stimulate the biodegradation of oil by indigenous microorganisms. JE1058BS, which is a powder, can be applied using conventional spraying equipment, for example a powder mist duster attached with boom type multi-hole head. 2. Concentration/Application Rate: JE1058BS is applied in a product:oil ratio of 1:10. No pre-mixing or dilution by water is required. 3. Conditions for Use: JE1058BS may be used in a wide range of environmental conditions of temperature and salinities where natural populations of oil-degrading microbes are active. The mechanical removal of as much oil as possible should be done before the product is introduced to the slick. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 48,213 11,413 0 NUTRIENT 51,833 13,056 JE1058BS 52,280 13,211 CONTROL 48,030 11,108 7 NUTRIENT 33,423 11,755 JE1058BS 13,453 10,188 CONTROL 48,257 0 10,429 8.6 28 NUTRIENT 16,953 67.3 11,837 9.3 JE1058BS 3,854 92.6 8,061 39.0 Bioremediation Agents 43 JE1058BS ------- Results of Gravimetric Analysis: DATA MISSING Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 5.9% 60.0% 81.8% b. Toxicity: Material Tested Species LC50 (ppm) JE1058BS Menidia beryllina 91.70 96-hr Mysidopsis bahia 72.09 48-hr No. 2 Fuel Oil Menidia beryllina 5.56 96-hr Mysidopsis bahia 2.19 48-hr JE1058BS &No. 2 Fuel Oil (1:10) Menidia beryllina 8.68 96-hr Mysidopsis bahia 2.44 48-hr Reference Toxicant (SLS) Menidia beryllina 12.23 96-hr Mysidopsis bahia 11.70 48-hr VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: NA 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: Store in dry location and avoid contact with moisture 4. Special nutrient requirements: NA 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 44 JE1058BS ------- TECHNICAL PRODUCT BULLETIN B-59 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 24, 2008 "BIOWORLD BIOREMEDIATION TREATMENT PRODUCTS (BIOWORLD BHTP)" I. NAME, BRAND, OR TRADEMARK BIOWORLD BIOREMEDIATION TREATMENT PRODUCTS (BIOWORLD BHTP) Type of Product: Bioremediation Agent (Microbiological Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT BioWorld USA, Inc. 6734B W Pershing Ave Visalia, CA 93291 Phone: (559) 651-2042 Fax:(559)651-9041 E-mail: support@bioworldusa.com Website: www.bioworldusa.com (Ms. Diane R. Barnes) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS BioWorld USA, Inc. 6734B W Pershing Ave Visalia, CA 93291 Phone: (559) 651-2042 Fax:(559)651-9041 E-mail: support@bioworldusa.com Website: www.bioworldusa.com (Mr. Donald E. Damschen) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-hazardous. 2. Ventilation: Use adequate ventilation. Treat dry product as a hygroscopic powder and avoid ventilation. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with eyes and do not take internally. Upon contact with eyes, flush with plenty of fresh water. Avoid breathing dust. Normal protective equipment for handling of powder, such as a dust mask and eye shield are recommended to be used. Wash hands and body contacted areas with soap and water. 4.a. Maximum storage temperature: 110°F 4.b. Minimum storage temperature: 34°F - containers may break if frozen 4.c. Optimum storage temperature range: 34°F - 90°F 4.d. Temperatures of phase separations and chemical changes: <32°F and > 140°F Bioremediation Agents 45 (BIOWORLD BHTP) ------- V. SHELF LIFE The recommended shelf life exceeds 3 years when stored properly in cool, dry place out of direct sun light. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: BioWorld BHTP is a two part product 1) Bioremediation Enhancer liquid and 2) Hydrocarbon Digesting Microbes in a dry form. Prior to use the microbes are rehydrated in 100°F water for 10 to 300 minutes. Example for small volume applications - best results are obtained by applying Bioremediation Enhancer first followed by the rehydrated Hydrocarbon Microbe solution in the same location. Example for large volume applications - the two parts of BioWorld BHTP can be mixed with additional water and applied together to spray over the perimeter and over the top of the spill. Example for soil and groundwater applications - evenly apply to soils and mix with till or discing equipment. Oxygen additions are periodically used in certain situations and can be applied with mechanical generation and/or by using oxygen release compound products. 2. Concentration/Application Rate: BioWorld BHTP is applied at an approximate rate of 40 gallons Bioremediation Enhancer liquid and 4 pounds Hydrocarbon Microbes per surface acre treated. Increased quantities and multiple applications may be required to meet shorter cleanup time constraints and desired results. 3. Conditions for Use: BioWorld BHTP can be used in freshwater conditions, wetlands, rock or sand shorelines, contaminated soil areas, salt marshes and salt water conditions (up to 60 ppt salinity). VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 61,234 9,395 0 NUTRIENT 64,803 8,873 BioWorld BHTP 63,192 9,220 CONTROL 57,907 5 7,290 22 7 NUTRIENT 49,747 14 5,956 18 BioWorld BHTP 41,480 28 4,405 40 Bioremediation Agents 46 (BIOWORLD BHTP) ------- CONTROL 49,364 19 6,499 31 28 NUTRIENT 21,490 67 5,259 41 BioWorld BHTP 1,948 97 1,078 88 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 21% 64% 96% b. Toxicity: Material Tested Species LC50 (DDm) BioWorld BHTP Menidia beryllina 8,848.70 96-hr Mysidopsis bahia 7,348.70 48-hr No. 2 Fuel Oil Menidia beryllina 4.50 96-hr Mysidopsis bahia 3.21 48-hr BioWorld BHTP & Menidia beryllina 13.90 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 7.10 48-hr Reference Toxicant (SLS) Menidia beryllina 15.00 96-hr Mysidopsis bahia 15.90 48-hr VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 6-8 Temperature: 80°F-100°F Salinity: 0-1 for use of the additive 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 3-10 Temperature: 33°F-120°F Salinity: >5 Use under any conditions where indigenous populations of oil-degrading microbes are/are not present 4. Special nutrient requirements: Some sites may benefit with various nutrients added depending on project variables 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: <2 Shigella: Negative Staphylococcus Coagulase positive: <10 Beta hemolytic Streptococci: <10 Bioremediation Agents 47 (BIOWORLD BHTP) ------- IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 48 (BIOWORLD BHTP) ------- TECHNICAL PRODUCT BULLETIN: B-60 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: OCTOBER 28, 2010 "MUNOX SR®" I. NAME, BRAND, OR TRADEMARK MUNOX SR® Type of Product: Bioremediation Agent (Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Osprey Biotechnics, a division of Phibro Animal Health Corporation 1845 57th Street Sarasota, FL 34243 Phone: (941)351-2700 Fax: (941)351-0026 E-mail: troy.smith@pahc.com (Mr. Troy Smith, Sr. VP Technical Operations E-mail: thomas.baldeschwieler@pahc.com (Mr. Thomas Baldeschwieler, Regulatory) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Osprey Biotechnics a division of Phibro Animal Health Corporation 1845 57th Street Sarasota, FL 34243 Phone: (941)351-2700 Fax: (941)351-0026 E-mail: rafael.bortoleto@pahc.com (Mr. Rafael Bortoleto, Sr. Director - Microbial Operations) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: No special ventilation is required under normal use. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special handling necessary. In case of skin contact, wash with soap and water. In case of eye contact, flush with water. In case of eye contact, flush with water. Wear protective gloves and wash hands with soap and water after handling. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 35°F to 95°F. Store in a cool, dry location. 4.d. Temperatures of phase separations and chemical changes: <32°F and >212°F V. SHELF LIFE MUNOX SR® is stable for over one year when stored at temperatures from 35°F to 95°F. Bioremediation Agents 49 MUNOX SR® ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: MUNOX SR® is a consortium of robust organisms that tolerate the natural salinity of seawater up to approximately 5% and water temperatures below 100°F. MUNOX SR® is effective on fresh and weathered crude oil and refined products because the metabolic pathways of the organisms are based on beta oxidation that is effective on a wide range of constituents of petroleum including aromatic, aliphatic and polyaromatic compounds. MUNOX SR® is provided with a microbial density of lxlO8 cfu/mL in stabilized liquid form or after the freeze-dried form is hydrated. The target population for effective treatment is 2.5xl05 cfu/mL. One unit consists of one 55-gallon drum of hydrated MUNOX SR® or the amount of freeze-dried powder to mix with 55-gallons of water to formulate the equivalent hydrated microbial solution. Based on this formulation and treatment ratio, one unit of MUNOX SR® will treat approximately 22,000 gallons of impacted water. Apply using in situ, hand sprayer, pump, pressure washer, etc. Product is ready to use and does not require dilution of additional formulation. 2. Concentration/Application Rate: Surface water: MUNOX SR® provides organisms that can be effective in the destruction and removal of petroleum hydrocarbons in surface water. It is best applied in areas where vertical water mixing is minimal in order to maintain high microbial density in the vicinity of floating hydrocarbons and near the water surface where there is a maximal oxygen concentration.. Beach application: The best application on the beach is by mixing the microbes in the beach between the tide marks. Assuming the contractor will be mixing the microbes to a depth of 12 inches and there is 30% porosity, 5 drums per acres will provide sufficient MUNOX SR® microbes for treatment. Marsh or wetland application: This application of MUNOX SR® provides the greatest value because it is the treatment approach that will not cause more damage to the wetlands. The microbes will be sprayed on the oiled wetland from a boat or aircraft so the vegetation is not disturbed. The recommended volume of MUNOX SR® will provide enough microbes to degrade a moderate oiling level to acceptable levels. This application rate will treat the oil in surface water, attached to vegetation, and on the soil surface. Assuming the wetland is submerged to a depth of six inches during high tide, an application rate of 8 units per acre will provide sufficient microbes for treatment. 3. Conditions for Use: MUNOX SR® is formulated for the bioremediation and metabolism of a wide range of petroleum hydrocarbons including crude oil and refined fuels. Because petroleum in all of its forms is made up of a wide variety of components, the dosage and application of MUNOX SR® will depend on the type of hydrocarbon, degree of weathering, and environmental conditions. Heavy petroleum compounds such as crude oil and refined products, such as bunker fuel, with a high proportion of complex aliphatics will require a high dosage than lighter petroleum compounds such as gasoline. The dosage will be site specific and will be determined with the assistance of CL Solutions at no cost to the U.S. EPA or the user. Bioremediation Agents 50 MUNOX SR® ------- MUNOX SR® will tolerate a wide range of environmental conditions; however, some conditions may reduce the effectiveness of MUNOX SR®. MUNOX SR® is most effective at a neutral pH, but can tolerate a pH range from 5 to 8.5. The salinity of water should be less than 5%. MUNOX SR® will also be most effective at moderately high temperatures from 70°F to 100°F. MUNOX SR® will tolerate low temperatures and will become dormant at freezing temperatures. However, MUNOX SR® will not tolerate temperatures above 105°F. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 1,003 0 3,609 0 0 NUTRIENT 1,096 0 4,661 0 MUNOX SR® 806 0 4,063 0 CONTROL 1,039 0 3,932 0 7 NUTRIENT 815 0 3,172 0 MUNOX SR® 199 0 3,292 0 CONTROL 847 15.5 3,578 0.85 28 NUTRIENT 832 24 3,674 21.2 MUNOX SR® 41 94.9 996 75.5 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 0.2. 9.9% 14.3% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: Bioremediation Agents 51 MUNOX SR® ------- pH: 6-8 Temperature: 4°C-35°C Salinity: Fresh water to salt water, <110 ppm 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: <6.0 and >8.0 Temperature: <4°C->35°C Salinity: >110 ppm 4. Special nutrient requirements: None required. In application, MUNOX SR® may be supplemented with the following Nutrient Mix at a ratio up to 1:10. Nutrient Mix Composition: Soy Peptone - 2.2% Yeast Extract - 2.2% Dextrose - 0.2% Sodium Nitrate - 0.2% Di-potassium Phosphate - 0.2% Sodium Thiosulfate - 0.01% 5. Test results regarding the determination of the presence of the following: Salmonella: Negative. Fecal coliform: Negative. Shigella: Negative. Staphylococcus Coagulase positive: Negative. Beta hemolytic Streptococci: Negative. IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 52 MUNOX SR® ------- TECHNICAL PRODUCT BULLETIN: B-61 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 17, 2010 "SOIL RX" (aka, BIO-REGEN HYDROCARBON) I. NAME, BRAND, OR TRADEMARK SOIL RX (aka, BIO-REGEN HYDROCARBON) Type of Product: Bioremediation Agent (Microbiological Culture, Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT 3 Tier Technologies LLC Worldwide Headquarters 413 W 13th Street Sanford, FL 32771 Phone: (877) 226-7498 Fax:(877)570-0072 E-mail: dburdette@3 tiertech.com Website: www.3tiertech.com (Daniel J. Burdette, President) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Direct Sales 3 Tier Technologies LLC Worldwide Headquarters 413 W 13th Street Phone: (877) 226-7498 Fax:(877)570-0072 E-mail: dburdette@3 ti ertech. com Website: www.3tiertech.com (Daniel J. Burdette, President) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal ventilation is adequate. 3. Skin and eye contact; protective clothing; treatment in case of contact: Ingestion: No effect if ingested in small amounts. A single dose of this product is rarely toxic by ingestion. Irritation of the mouth, pharynx, esophagus and stomach can develop. Give two glasses of water. Do not induce vomiting. Contact physician if needed. Eyes: Avoid eye contact. This material may cause eye irritation. Immediately flush with water for 15 minutes. Contact physician if needed. Skin: Slight redness on hands and forearms if individual has a history of dermal allergic reactions. Dermatitis and skin sensitization can develop after repeated and/or prolonged contact. Remove contaminated clothing and footwear. Wash with soap and water. Bioremediation Agents 53 SOIL RX ------- Always consult a physician if needed. Respirators are not required for recommended uses. Rubber gloves are not required, but recommended. Safety glasses are not required, but recommended. Wash hands with soap and water after handling product. Wash contaminated clothing and footwear before reuse. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 34°F - do not allow product to freeze 4.c. Optimum storage temperature range: 45°F to 95°F. 4.d. Temperatures of phase separations and chemical changes: NA, stable. V. SHELF LIFE Shelf life exceeds 2 years when properly stored in the unopened original container. VI. RECOMMENDED APPLICATION PROCEDURE SOIL RX (aka, BIO-REGEN HYDROCARBON) is a concentrated liquid formulation of activated humic acid, highly concentrated hydrocarbon-oxidizing bacteria, and a readily biodegradable natural amino acid complex consisting of a nutrient-rich extract with a broad- spectrum package of identifiable amino acids, surfactants, and other proteins. This product is designed to digest organics and hydrocarbons in soil and water. 1. Application Method: SOIL RX (aka, BIO-REGEN HYDROCARBON) is a liquid concentrate that must be diluted prior to use. The product can be sprayed after dilution using standard spray application equipment, including but not limited to hand sprayers, mechanical sprayers, water trucks, fire or emergency response equipment, pressure washers, etc. Mix or saturate concentrate/water mixture with contaminated soils thoroughly for maximum performance. For shallow/surface contamination, drench affected areas with enough dilution to fully saturate the soil using normal spray equipment and water trucks. For general contamination less than two feet, contaminated soil may require tilling or excavation to properly mix concentrate/water dilution into soils. For deeper contamination greater than two feet, product application can be applied through boring the area and using perforated piping per regulatory recommendations or excavate the material and treat while land farming or bio-piling. For contaminated water, such as marshes, shoreline and open water with floating hydrocarbons, apply dilution directly to the contaminated areas using appropriate spray equipment and water cannons. 2. Concentration/Application Rate: SOIL RX (aka, BIO-REGEN HYDROCARBON) must be diluted using 1 part concentrate to 10 parts clean water prior to use. Product can be diluted up to 100 parts water as directed for specific applications. Application rates are determined by level of contamination, area of application, and speed required for cleanup. Specific application rates are determined prior to sale by the manufacturer and the distributor. A normal application rate for contaminated soil is on gallon 10:1 diluted product per cubic yard of soil. Normal application rate for water applications is three gallons 10:1 diluted product per 1000 square feet of contaminated surface area. 3. Conditions for Use: SOIL RX (aka, BIO-REGEN HYDROCARBON) is safe for application in ocean and fresh water, all soil types, and shoreline treatments. Water Salinity: Product should be diluted with fresh, clean water. Use of brackish or brine water may be used if fresh water is not available. It should be noted that the use of brine water may slightly reduce product performance or increase overall remediation time. Bioremediation Agents 54 SOIL RX ------- Water Temperature: Water must be between 42° to 110°F for normal product performance. pH: Optimum water pH ranges between 4 to 8. Temperature: Temperatures are below 32° and above 120°F may decrease product performance. Nutrient Requirements: None. Nutrients required are in the product. Type and Age of Pollutants: For use on most organic based contaminants and hydrocarbon based materials like gasoline, jet fuels, diesel fuels, grease, tar, motor oils, crude oils, solvents, etc. Age of contamination is not a factor as much as level of contamination, depth of contamination, and length of time required for the remediation process. For materials that have hardened and are tar- like, additional procedures may be required for effective remediation. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 34908.9 0 6051.3 0 0 NUTRIENT 34863.3 0 6047.4 0 SOIL RX 34993.0 0 6069.0 0 CONTROL 35206.2 +0.08 5720.9 5.45 7 NUTRIENT 32894.1 5.64 5745.8 4.98 SOIL RX 24446.0 30.14 3219.2 46.96 CONTROL 34287.8 1.779 5892.7 2.621 28 NUTRIENT 32610.0 6.463 5205.1 13.928 SOIL RX 17597.0 49.713 1600.1 73.635 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 8.01% 7.43% 30.14% b. Toxicity: NA Bioremediation Agents 55 SOIL RX ------- VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 4-8 Temperature: 42°F-100°F Salinity: NA 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 2-10 Temperature: 34°F-125°F Salinity: NA 4. Special nutrient requirements: None 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 56 SOIL RX ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN: B-62 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: DECEMBER 15, 2010 "PRO-ACT" (aka, OILCLEAN w/ACTIVATOR) I. NAME, BRAND, OR TRADEMARK PRO-ACT (aka, OILCLEAN w/ACTIVATOR) Type of Product: Bioremediation Agent (Biological Additive: Microbiological Culture w/ Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Pro-Act Biotech a Unit of LLG.LLC 64 Church Street Warren, RI 02885 Phone: (401)245-7004 Fax: (401)633-6270 E-mail: bill@proactbiotech.com Website: www.oil-clean.net (Mr. William Campion) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Pro-Act Biotech a Unit of LLG.LLC 64 Church Street Warren, RI 02885 Phone: (401)245-7004 Fax: (401)633-6270 E-mail: bill@proactbiotech.com Website: www.oil-clean.net (Mr. William Campion) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing is required in the handling, storage and field application of this product. For skin and eye contact, wear goggles. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 110°F, up to 5 days 4.b. Minimum storage temperature: 35°F, do not freeze 4.c. Optimum storage temperature range: 40°F to 90°F 2/04/2020 7/27/2022 Bioremediation Agents 57 PRO-ACT ------- V. SHELF LIFE One year as packaged. VI. RECOMMENDED APPLICATION PROCEDURE PRO-ACT (aka, OILCLEAN w/ACTIVATOR) consists of two parts: liquid microbes and activator (i.e., nutrient additive). As part of the Product Schedule, training on the proper use of PRO-ACT (aka, OILCLEAN w/ACTIVATOR) will be provided by Pro-Act Microbial, Inc. certified personnel. 1. Application Method: Site (water and/or soil) testing is highly recommended prior to product application. The testing is designed to assess the nutrient status of the contaminated site. The desired nitrogen and phosphorus concentrations are in the range of 0.5 to 2.5 mg N/L for nitrogen and 0.05 to 0.3 mg P/L for phosphorus. If there are inadequate nutrients in the water/soil, the activator portion will be needed to bring the nutrients in line with product specification. The activator portion can be applied directly to the site for treatment or it can be mixed in with the diluted liquid microbes first. Nutrient levels need to be maintained for optimal microbial action. Thus, depending on the nature of water/soil and the results of on site monitoring, activator may need to be applied more than once. It is recommended that physical methods such as skimming should be employed to recover as much oil as possible. PRO-ACT (aka, OILCLEAN w/ACTIVATOR) should be used to breakdown the residual oil after the physical methods have been used. 2. Concentration/Application Rate: Liquid microbes are to be diluted with the non-chlorinated, non-ozonated water or with the water to be treated (1:10 liquid microbe/water ratio) and applied with a sprayer, either pump or pneumatic. The amount of PRO-ACT (aka, OILCLEAN w/ACTIVATOR) needed depends on the amount of oil to be treated. One gallon undiluted liquid microbes can treat up to 1000 square feet, assuming there is less than Vi inch of oil on surface. For example, one gallon undiluted liquid microbes is good for up to 5 gallons of spilled oil. A second application of Pro-Act (aka OilClean w/Activator) is beneficial to speed up the bioremediation process. 3. Conditions for Use: Monitoring of dissolved oxygen levels is recommended. If needed, a mechanical aeration device should be deployed to maintain DO levels above 3 mg/L. PRO-ACT (aka, OILCLEAN w/ACTIVATOR) works with fresh oil as well as weathered oil. Oil toxicity (especially from easily dissolved shorter chain hydrocarbons in the fresh oil) should not be a problem as long as physical methods are used first following a spill. The product is ideal for salt water, brackish water and fresh water, with no limitations as to usage within optimum temperature range of 20 to 400°C. Bioremediation Agents 58 PRO-ACT ------- VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 41277 0 6100 0 0 NUTRIENT 41670 0 6140 0 PRO-ACT 43193 0 6460 0 CONTROL 41393 0 5705 0 7 NUTRIENT 26370 0 3640 0 PRO-ACT 302 0 1979 0 CONTROL 42451 -2.766 4546 25.475 28 NUTRIENT 3654 91.231 1968 67.948 PRO-ACT 59 99.863 378 94.149 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 12.624% 55.670% 65.516% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 7.0 Temperature: 30°C Salinity: 0.2 to 4% 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: <6.0 or >9.0 Temperature: <15°C or >45°C Bioremediation Agents 59 PRO-ACT ------- Salinity: <0.02% or >5% 4. Special nutrient requirements: PRO-ACT (aka, OILCLEAN w/ACTIVATOR) 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 60 PRO-ACT ------- TECHNICAL PRODUCT BULLETIN: B-63 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: DECEMBER 15, 2010 "BIOREM-2000 OIL DIGESTER™" I. NAME, BRAND, OR TRADEMARK BIOREM-2000 OIL DIGESTER™ Type of Product: Bioremediation Agent (Biological Additive: Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Clift Industries, Inc. P.O. Box 471578 Charlotte, NC 28247 Customer Service: Phone: (800) 996-9901 Product Management: Phone: (704) 752-0031 Fax:(704)544-2532 E-mail: matt@cliftindustries.com (Mr. Matt Barnhill) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Clift Industries, Inc. P.O. Box 471578 Charlotte, NC 28247 Customer Service: Phone: (800) 996-9901 Product Management: Phone: (704) 752-0031 Fax:(704)544-2532 E-mail: matt@cliftindustries.com (Mr. Matt Barnhill) X-Cel Chemical Specialties 921 Rosewood Street Jenison, MI 49428 Office: (616) 581-4324 Fax: (616) 777-0022 E-mail: 1 arry. hewitt@xcel chemi cal. com (Mr. Larry Hewitt, Primary Contact) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing is required in the handling, storage and field application of this product. For skin and eye contact, wear gloves and goggles. 4.a. Maximum storage temperature: 140°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 85°F Bioremediation Agents 61 BIOREM-2000 OIL DIGESTER™ ------- V. SHELF LIFE The shelf life of the product is two (2) years when stored within the storage temperature range in the original container. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spray from boats, aircraft, fire eductor systems on boats, helicopter buckets, hand-held or backpack sprayers, or from hoses attached to small pumps, water trucks and aerial spray, including typical spreading systems. 2. Concentration/Application Rate: Shoreline Treatment: To treat beaches, coarse sand, rocks, rip rap, sea walls, cobble shorelines and rocky shores, oiled pilings and piers use one (1) part BIOREM-2000 OIL DIGESTER™ diluted with five (5) parts water. Use one (1) gallon per 1,500 square feet of contaminated area. Treating Marine Vegetation/Wetlands: Dilute one (1) part BIOREM-2000 OIL DIGESTER™ with five (5) parts water and apply with non-pressure, non-impact spraying equipment onto reeds, grasses, trees, and rocks in marsh areas and vegetated wetlands. Use one (1) gallon per 1,500 square feet of contaminated area. For Treating Water: Do no dilute BIOREM-2000 OIL DIGESTER™ and apply directly spraying onto the surface of oil. Small Applications: BIOREM-2000 OIL DIGESTER™ may be applied with hand sprayers or portable pumps to spray the product directly onto oiled surfaces. Dose rates will vary with the type and amount of petroleum spilled, the extent of weathering, and other site-specific conditions, including temperature, porosity of surface, and residence time available to let the product contact the oil. 3. Conditions for Use: Effective at temperatures above 40°F. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 0 NUTRIENT 43163 0 6001 0 36643 0 4813 0 Bioremediation Agents 62 BIOREM-2000 OIL DIGESTER™ ------- BIOREM-2000 OIL DIGESTER™ 36492 0 4634 0 CONTROL 39249 9.0 5067 15.5 NUTRIENT 2946 91.9 3832 20.0 7 BIOREM-2000 OIL DIGESTER™ 5390 85.2 4114 11.0 CONTROL 33961 21.0 3812 36.0 NUTRIENT 106 99.7 729 84.0 28 BIOREM-2000 OIL DIGESTER™ 64 99.8 1324 71.0 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 10.7% 68.9% 67.0% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 7.0 Temperature: 85°F Salinity: <10% 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 3.0 or 11.5 Temperature: <35°F or>125°F Salinity: >40% 4. Special nutrient requirements: None 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative Bioremediation Agents 63 BIOREM-2000 OIL DIGESTER™ ------- IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 64 BIOREM-2000 OIL DIGESTER™ ------- TECHNICAL PRODUCT BULLETIN: B-64 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: FEBRUARY 22, 2011 "DRYLET™ MB BIO" I. NAME, BRAND, OR TRADEMARK DRYLET™ MB BIO Type of Product: Bioremediation Agent (Biological Additive: Microbiological Culture) (formerly DRYLET™ MB BIOREMEDIATION) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Dry let, Inc. 8300 FM 1960 West Suite #450 Houston, TX 77070 Phone: (346) 980-9570 E-mail: sales@drylet.com (Mr. Scott Conley) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Dry let, Inc. 8300 FM 1960 West Suite #450 Houston, TX 77070 Phone: (346) 980-9570 E-mail: sales@drylet.com (Mr. Scott Conley) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements. In closed spaces, uses dust protective measures. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing is required; however, goggles and dust mask are recommended. Applying dry powder may cause irritation to membranes. If eye or skin irritation occurs, flush with plenty of water. 4.a. Maximum storage temperature: 120°F continuous 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F V. SHELF LIFE Minimum 5 years, with proper storage, in original packaging. Freezing does not harm shelf life; however, extreme heat (over 180°F) for long periods of time can shorten shelf life. Bioremediation Agents 65 DRYLET™ MB BIO ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Apply DRYLET™ MB BIO directly to oil contamination. DRYLET™ MB BIO may be applied by the usual methods of aerial or manual broadcast spreading. For smaller spills, manual broadcast will deliver the best results. Larger spills in open water, marsh, wetlands, or estuary areas should be treated by aerial powder dusting or dusting with mechanical powder pumps. 2. Concentration/Application Rate: Apply DRYLET™ MB BIO directly on the spill. Apply 0.4 pounds of product per cubic yard of soil, or 50 pounds per acre of open water slick. In marsh, wetlands, and estuaries application rates may be up to 75 pounds per acre depending on the oil type and contamination level. 3. Conditions for Use: Water salinity: can be used in fresh or salt water. pH: 4 to 11.5. Temperature: 32°F - 120°F. Water Temperature: 35°F - 170°F. Nutrient Requirements: Nutrients are included with the product. However, for longer term project, additional nutrients may be added to increase microbial activity. Types and Ages of Contamination: For use on organic and hydrocarbon-based contamination. Tar like contamination may require mechanically breaking the structure to obtain timely results. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 60871 0 8729 0 0 NUTRIENT 61995 0 8170 0 PRODUCT 61459 0 8790 0 CONTROL 56197 0 6224 0 7 NUTRIENT 42501 0 4833 0 PRODUCT 12303 0 4140 0 CONTROL 27314 55.0 5030 42.4 28 NUTRIENT 47 99.9 533 93.5 PRODUCT 820 98.6 1305 85.1 Bioremediation Agents 66 DRYLET™ MB BIO ------- Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control 0.30% Nutrient 50.0% Product 84.8% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 6.0-8.0 Temperature: 85°F to 110°F Salinity: 0.5-4.0 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 4.0 or 11.5 Temperature: 35°F or 180°F Salinity: 0.5 or 5.0 (above 4.5 reduces effectiveness by half) 4. Special nutrient requirements: None 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 67 DRYLET™ MB BIO ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 3/17/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN: B-65 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: MAY 18, 2011 "DUALZORB®" (aka, TRAILZORB, WHITZORB) I. NAME, BRAND, OR TRADEMARK DUALZORB® (aka, TRAILZORB, WHITZORB) Type of Product: Bioremediation Agent (Biological Additive: Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT LBI Renewable P.O. Box 637 22 Plains Drive Buffalo, WY 82834 CUSTOMER SERVICE: Phone: updated information required Fax: updated information required E-mail: updated information required (Mr. Aaron Larsen) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS DUALZORB® and TRAILZORB: LBI Renewable P.O. Box 637 22 Plains Drive Buffalo, WY 82834 CUSTOMER SERVICE: Phone: updated information required Fax: updated information required E-mail: updated information required (Mr. Aaron Larsen) WHITZORB: Whit more Manufacturing Co. 930 Whit more Drive Rockwall, TX 75032 CUSTOMER SERVICE: Phone: (972) 771-1000, ext. 241 Fax: (972) 722-4561 E-mail: mkellis@whitmores.com (Ms. Mary Kathryn Ellis) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: DUALZORB® is classified as non-flammable by DOT regulations (49 CFR 173. 124) 2. Ventilation: DUALZORB" is not volatile and does not require ventilation. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye contact due to mechanical abrasion. In case of eye contact, immediately flush eyes with large amounts of water until particles are evacuated. Goggles are recommended during use. Bioremediation Agents 68 DUALZORB® ------- 4.a. Maximum storage temperature: 200°F continuous 4.b. Minimum storage temperature: NA 4.c. Optimum storage temperature range: 32°F to 100°F 4.d. Temperatures of phase separation and chemical changes: DUALZORB® should be stored out of the weather and should not be exposed to direct sun light for extended periods of time. V. SHELF LIFE Guaranteed shelf life of unopened product is 5 years if not exposed to weather or direct sunlight. VI. RECOMMENDED APPLICATION PROCEDURE DUALZORB® is a dehydrated product that must be hydrated for maximum effectiveness to bioremediate hydrocarbons in soil and water. Hydration can be accomplished with fresh or sea water. Additionally, it can be applied on a surface and hydrated with natural precipitation. 1. Application Method: This product can be applied by hand, mechanical spreaders, portable mixer or blown onto a surface using an air conveyor. Mix hydrated DualZorb® with oil contaminated soil, sand, or rocks by either hand, shovel or till into the soil with power equipment. DUALZORB® will absorb approximately 80% of the oil from soil and sand in the first 2 hours of application, with, continued bioremediation of oil. The bioremediation effect of this product is not affected by water salinity, temperature, or oil type and age. However, the oil absorption capacity is reduced in the presence of salt water as it will also absorb salts. For hard surface stains and cleanup, hydrated product can be rubbed by hand over the surface until it will no longer absorb oil. Place the spent product in an approved, labeled container in accordance with local, state, federal, international, or country specific regulations. Depending upon the compound(s) absorbed, this product may be disposed in a landfill, incinerated, or land farmed. This product has a heat value of 842 IBtu pound and an ash content of 0.35%. For in situ applications, the hydrated DUALZORB® can be tilled into the contaminated soil. 2. Concentration/Application Rate: DUALZORB* is packaged in a dehydrated form and expands three times its original volume when retrydrated with either fresh or 1.5 times with salt water. This product should be mixed on a 1:1 volume basis with hydration water. For every 1 gallon of oil, 4 pounds of DUALZORB® is recommended. For in situ applications, 50 pounds of hydrated DUALZORB* is recommended per cubic yard of soil. 3. Conditions for Use: DUALZORB* is manufactured for land use and will absorb hydrocarbon, waste oil, and fuel spills. DUALZORB® is not affected by cold water but may require additional contact time. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Bioremediation Agents 69 DUALZORB® ------- Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 255,568 0 10,816 0 0 NUTRIENT 255,414 0 10,821 0 PRODUCT 248,869 0 12,738 0 CONTROL 244,841 0 10,290 0 7 NUTRIENT 79,688 0 9,963 0 PRODUCT 14,254 0 11,168 0 CONTROL 215,169 15.8 7,908 26.9 28 NUTRIENT 2,407 99.1 9,393 13.2 PRODUCT 1,545 99.4 950 92.5 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 0.4% 15.4% 30.0% b. Toxicity: Materials Tested DUALZORB ® No. 2 Fuel Oil DUALZORB® & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 1,414.21 96-hr 1,096.05 48-hr 7.08 96-hr 1.13 48-hr 8.43 96-hr 2.70 48-hr 12.25 96-hr 11.71 48-hr VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of all microorganisms by species and percentages in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 6.5-7.5 Temperature: 60°F to 100°F Salinity: 0-10% Bioremediation Agents 70 DUALZORB® ------- 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 5.5-9.0 Temperature: 45°F and 105°F Salinity: 0-10% 4. Special nutrient requirements: LBI Renewable recommends nutrient supplement s of maximum performance for bioremediation or in-situ applications. Contact LBI Renewable for project specific nutrient dosing. 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES 1. Flash Point: NA 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: 2.25 g/mL 5. pH: NA 6. Surface Washing Agents: NA 7. Solvents: NA 8. Additives: None 9. Solubility: NA X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons CYANIDE, AND CHLORINATED Concentration (ppm) 0.185 0.185 0.500 0.537 <0.185 <0.00303 <0.463 9.35 <0.060 <0.024 Bioremediation Agents 71 DUALZORB® ------- TECHNICAL PRODUCT BULLETIN: B-66 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JUNE 08, 2011 "REMEDIADE™" (aka, SP 7010) I. NAME, BRAND, OR TRADEMARK REMEDIADE™ (aka, SP 7010) Type of Product: Bioremediation Agent (Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT GrowMate International, LLC 17150 Butte Creek Drive, Suite 100 Houston, TX 77090 Phone: (281) 866-9042 Fax: (281)866-9714 E-mail: victor@growmateintl.com Website: www.growmateintl.com (Mr. Victor J. Cardenas) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS GrowMate International, LLC 17150 Butte Creek Drive, Suite 100 Houston, TX 77090 Phone: (281)866-9042 Fax: (281) 866-9714 E-mail: victor@growmateintl.com Website: www.growmateintl.com (Mr. Victor J. Cardenas) VariChem International, Inc. 78330 Hi Way 35 North Bay City, TX 77414 Phone: (979) 245-7278 Fax: (979) 245-0612 E-mail: Gordon@varichemusa.com Website: www.varichemusa.com (Mr. Gordon Winfrey) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: As defined by OSHA's Hazard Communication Standard, this product is non-hazardous with no evidence of adverse effects. Use safety glasses when handling for eye protection. Store in a cool dry place. Flush eyes and wash skin if contacted. In the event of contact with skin, wash with water. In the event of contact with eyes, rinse with water. In the event of contact with clothing or surfaces such as floors or counter tops, rinse with water and dry. In the event of spilling onto land or water, no handling or rinsing requirements are needed. No other safety or handling precautions need to be adhered to in the event of contact or spills. 4.a. Maximum storage temperature: 115°F continuous 4.b. Minimum storage temperature: 32°F Bioremediation Agents 72 REMEDIADE™ ------- 4.c. Optimum storage temperature range: 40°F to 98°F 4.d. Temperatures of phase separation and chemical changes: NA V. SHELF LIFE Shelf life of product unopened is 2 years. If the container has been opened, but uncontaminated and is resealed properly, the shelf life is 1 year after initial opening. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Product may be applied to any surface for removal of hydrocarbons. For treatment of large areas, properly diluted product may be applied by spraying with a pressure washer, portable fire pump or any other suitable pump with non-chlorinated fresh water or salt water. Application can also be made with normal spray equipment via a 1" or larger hose and a spray nozzle, similar to a fire nozzle. Eductor setups, water trucks as well as fire or other emergency response equipment may be used. Aircraft application is also effective in covering large areas or contaminated water. 2. Concentration/Application Rate: For in-situ soils, till the REMEDIADE™/water mixture onto the contaminated area. Soil treatment rate guidelines are 1 gallon of concentrate for 30 cubic yards of soil for each 20,000 TPH contamination level. Example: 40,000 TPH level would be 2 gallons per 30 cubic yards. Clay soils may take more product and sandy soils may take less. After the treatment rate is established, apply l/3rd of the product mixture on the first day, wait 5 to 7 days and apply the second l/3rd of the product mixture, wait another 5 to 7 days and apply the final l/3rd of the product mixture. During each of the three applications apply '/2 of the product mixture to the affected soil. Till or blade in this application before applying the second V2 of the product mixture. This will help the product get good coverage and disperse well into the soil. In the event of oil spills on water, treatment guidelines are 1 gallon of concentrate per 30 square foot of surface area. After the treatment rate is established, apply l/3rd over the area and wait 5 to 7 days and apply the second treatment. Then wait 2 to 5 days and apply the third treatment. Light gravity oils may take more. When spraying the product over oil, good agitation of the contaminant with the product can only help. This helps add to surface contact and aids in the bioremediation process. Salinity of the water will not make a difference in the effectiveness of the product. 3. Conditions for Use: Product must be mixed with non-chlorinated water, but it can be used with fresh, salt or brackish water. Reapplication may be necessary in severely contaminated areas. Be sure to apply the product on three separate days, allowing time in between the days, this helps keep bacteria counts up at a more consistent level through the process. Adding all the product in one treatment will only prove to waste product and slow the effectiveness of the overall remediation process. Bioremediation Agents 73 REMEDIADE™ ------- VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL RED% MEAN MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 255,568 0 10,822 0 0 NUTRIENT 255,414 0 10,821 0 PRODUCT 245,168 0 10,816 0 CONTROL 244,841 0 10,920 0 7 NUTRIENT 215,169 0 9,963 0 PRODUCT 79,688 0 9,393 0 CONTROL 21,469 91.6 9,067 16.2 28 NUTRIENT 4,198 98.4 7,908 26.9 PRODUCT 2,404 99.0 607 94.4 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 0.0% 17.8% 36.0% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS The product is a nutrient additive and does not contain microbiological cultures or enzyme additives. 1. Listing of each component of the formulation by chemical name and percentage by weight: CONFIDENTIAL 2. Optimum storage conditions: Temperature: 40°F to 98°F IX. PHYSICAL PROPERTIES NA Bioremediation Agents 74 REMEDIADE™ ------- X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 75 REMEDIADE™ ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN: B-67 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JULY 27, 2011 "ERGOFIT MICROMIX AQUA" I. NAME, BRAND, OR TRADEMARK ERGOFIT MICROMIX AQUA Type of Product: Bioremediation Agent (Microbiological Culture, Enzyme Additive, Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Evadine Technologies, LLC 217 Deborah Drive New Braunfels, TX 78130 Phone: updated information required E-mail: updated information required (Mr. Warren Russell) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Evadine Technologies, LLC 217 Deborah Drive New Braunfels, TX 78130 Phone: updated information required E-mail: updated information required (Mr. Warren Russell) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Water-based, Non-flammable 2. Ventilation: Needs no ventilation; aqueous-based organic product; does not emit hazardous vapors. Some CO2 may build up. 3. Skin and eye contact; protective clothing; treatment in case of contact: ERGOFIT MICROMIX AQUA is not a dermal irritant. Avoid eye contact, and wear goggles when using product. Eyewash for quick and copious eye flushing should be available on site. Seek prompt medical attention should contact occur and if irritation persists. Protective rubber gloves are suggested during handling. ERGOFIT MICROMIX AQUA has a smell of fermentation and yeast. The product does not give off harmful vapors. Long storage will cause build up of CO2 in water vapor. 4.a. Maximum storage temperature: 104°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 57°F to 97°F 4.d. Temperatures of phase separation and chemical changes: above 113°F 4/16/2017 7/27/2022 Bioremediation Agents 76 ERGOFIT MICROMIX AQUA ------- V. SHELF LIFE ERGOFIT MICROMIX AQUA has a recommended shelf life of 5 years. After 5 years at optimum storage in cool temperature there is an approximate 10% decrease per year in product effectiveness. Shelter from direct sunlight or extreme cold or heat source. In the event of fire, wash with water. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: ERGOFIT MICROMIX AQUA can be applied with any commercially available spray apparatus, such as small hand held tanks, back packs, large mixing tanks with mechanical pumping devices, vessels with booms for spraying wide paths, or liquid spray devices on crop duster airplanes or helicopters. ERGOFIT MICROMIX AQUA can also be applied by eductor systems from vessels, fire trucks, or any other outfitted vehicle. 2. Concentration/Application Rate: ERGOFIT MICROMIX AQUA generally takes 5 to 50 minutes to penetrate the molecular walls of hydrocarbons. Warmer conditions favor faster biological action whereas colder conditions may reduce the speed of decomposition. Once ERGOFIT MICROMIX AQUA is applied to the targeted areas, the microbes will attach themselves to the hydrocarbons and start to attack their carbon structure and metabolize into natural organic substances from the humus family. Aquatic plants and animal life will feed on this nutrient. Within hours odor will be negligent and changes will be noticeable in seven days, depending on the temperature. ERGOFIT MICROMIX AQUA will also break down the adhesive properties of the hydrocarbons, preventing oils from attaching to animals, vegetation, rocks, and earth. Dilution Rates: ERGOFIT MICROMIX AQUA should always be mixed with the native water of the affected area. Note: Do not use city water that has been treated with chlorine with ERGOFIT MICROMIX AQUA. This means that if you are treating an affected saltwater area, then saltwater should be used as your base carrier for the product. Likewise if you are treating a lake or river, then that carrier water would be the freshwater from that source. For general applications and light oil films, dilute each gallon of ERGOFIT MICROMIX AQUA with source water (e.g., fresh, brackish, or saltwater) at a ratio of 1:50. For oil mousse like formation in intertidal zones, use a dilution of 1:30. If the spill is very heavy and the oil layer is thick (more than 1 inch) it is recommended that ERGOFIT MICROMIX AQUA be applied at a lower ratio of 1:20. On land not involving water bodies, it is recommended that an organic absorbent be applied prior to using ERGOFIT MICROMIX AQUA to treat oil spills to remediate the CI and C35 Petroleum Hydrocarbons. This is to increase the contact surface area for ERGOFIT MICROMIX AQUA to convert spills oil and absorbent to organic humus. Application on Coastal Water: Apply the mixed solution using hand held sprayers, tank sprayers, booms from vessels, helicopters, or airplanes. First, start by spraying the outer perimeter of the spill and systematically work towards the middle of the affected area, making sure to cover the entire surface area of the spill. Use 1.5 gallons of ERGOFIT MICROMIX AQUA concentrate for every 1000 gallons of hydrocarbons spilled. Dilute it with 30 gallons of seawater per gallon of concentrate for spraying. [To calculate gallons of ERGOFIT MICROMIX AQUA required, multiply estimated gallons of hydrocarbons by 0.0015.] For denser hydrocarbons, like in the case of crude oil, multiply barrels of crude oil by 42 to get gallons of crude and apply above ratios. If Bioremediation Agents 77 ERGOFIT MICROMIX AQUA ------- you do not know gallons of hydrocarbons or barrels of crude oil, estimate size of spill by (1000 square yards x 2 inch average thickness) to arrive at gallons of oil spilled. Use 10 kg/22 lbs of ERGOFIT MICROMIX AQUA diluted to 50 gallons in water to cover this area. As a rule, 2 kg/4.4 lbs ERGOFIT MICROMIX AQUA is required per metric ton of oil spilled. Dilution varies depending on oil thickness or simple sheen floating on water surface. Application for Intertidal Zones: ERGOFIT MICROMIX AQUA should be applied at low tide, when the affected areas are exposed to the elements, allowing the product to securely attach to the hydrocarbons. Cease application if the tide rises and resume once the water level has receded again. Continue application cycle until the entire affected area has been coated. The recommended mix ratio is 1:30. In areas where a combination of high tide and waves have pushed the contamination beyond the intertidal zone, oil rag layer looking like chocolate mousse, cordon off the area and start spraying ERGOFIT MICROMIX AQUA diluted at a ratio of 1:20 in water. The objective is to get an application rate of between 1 to 2 gallons of concentrated ERGOFIT MICROMIX AQUA sprayed per 1000 gallons of hydrocarbons spilled. 3. Conditions for Use: ERGOFIT MICROMIX AQUA acts on all organic hydrocarbons on sea, fresh water, and land. As the age of spilled hydrocarbons increases, so does the time necessary for bioremediation. In general, fresh crude, gasoline of BTEX takes anywhere from 30 days to 12 months to completely bioremediate depending on weather conditions and density of spill. However, the remediation process will be noticeable throughout the process. Variations in seawater salinity, has no effect, as long as microbial life can exist, then ERGOFIT MICROMIX AQUA will be effective in salt and brackish water with a maximum salinity of 4.9 percent. ERGOFIT MICROMIX AQUA bioremediation slows somewhat at temperatures below 40°F. However, it will continue to work in any water temperatures that will sustain microbial life. Decreasing the amount of ERGOFIT MICROMIX AQUA per square yard from recommended dosage rates lengthens the remediation time. When nitrogen and carbon is added to ERGOFIT MICROMIX AQUA the initiation of bacterial-enzymatic activity is enhanced many fold to begin bioremediation within 2 hours of application. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS 0 CONTROL 239,235 0 16,502 0 PRODUCT 239,686 0 17,431 0 CONTROL 217,023 9.30 10,942 33.70 Bioremediation Agents 78 ERGOFIT MICROMIX AQUA ------- 7 PRODUCT 17,819 92.6 9,606 44.90 CONTROL 188,379 21.3 8,989 45.50 28 PRODUCT 2,216 99.10 3,100 82.20 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Product 1.7% 45.6% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS Microbiological Culture: 1. Listing of all microorganisms by species and percentage in the composition: CONFIDENTIAL 2. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 6.5 to 7.5. Temperature: 57°F to 97°F. Salinity: The maximum permissible salinity is up to 4.9% sodium by solution 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: Lower than 4.5 or higher than 8.5 reduces the product efficiency by 50 percent. Temperature: Lower than 32°F or higher than 104°F reduces the product efficiency by 50 percent. Salinity: The maximum permissible salinity is up to 4.9% sodium by solution 4. Special nutrient requirements: NA 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta Hemolytic Streptococci: Negative Enzyme Additive: 1. Listing of each component of the total formulation, other than enzymes, by chemical name and percentage by weight: CONFIDENTIAL 2. Enzyme Names: CONFIDENTIAL 3. I.U.B.: CONFIDENTIAL 4. Source of Enzymes: Plant or Fungi/Fermentation process 5. Units: No less than 1% and no more than 50% by weight 6. Specific Gravity: 1.00 7. Optimum Conditions: Bioremediation Agents 79 ERGOFIT MICROMIX AQUA ------- a. pH: 7.0 b. Temperature: 72°F c. Salinity Ranges: Fresh water to salt water up to 4.9% d. Minimum and Maximum pH: 4.5 - 8.5 e. Minimum and Maximum Temperature: 32°F - 104°F f. Minimum and Maximum Salinity Levels: Salinity level that will support microbial activity will not adversely a ERGOFIT MICROMIX AQUA performance g. Enzyme Shelf Life: Up to 5 years when properly stored h. Enzyme Optimal Storage Conditions: 72°F is optimal, enzyme range is freezing to 104°F, never leave ERGOFIT MICROMIX AQUA in direct sunlight for more than a couple of hours Nutrient Additive: 1. Listing of each component of the formulation by chemical name and percentage by weight: CONFIDENTIAL 2. Optimum storage conditions: Temperature: 32°F to 104°F IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 80 ERGOFIT MICROMIX AQUA ------- LISTING CHANGES PENDING; VERIFICATION BY MANUFACTURER AND EPA REQUIRED TECHNICAL PRODUCT BULLETIN: B-68 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: AUGUST 8, 2011 "SHAMANTRA GREEN" (aka, SHAMANTRA BIO) I. NAME, BRAND, OR TRADEMARK SHAMANTRA GREEN (aka, SHAMANTRA BIO) Type of Product: Bioremediation Agent (Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Molecular Mediation LLC C/- Molecular Mediation Pty Ltd Level 3, Suite 405 152 Bunnerong Road Eastgardens 2036 Australia Phone: +612-9659-4553 E-mail: info@molecularmediation.com E-mail: mark@molecularmediation.com (Mr. Mark Pilgrim, Manager) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Molecular Mediation PTY LTD Level 3, Suite 405 152 Bunnerong Road Eastgardens 2036 Australia Phone: +612-9659-4553 E-mail: info@molecularmediation.com E-mail: mark@molecularmediation.com (Mr. Mark Pilgrim, Manager) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required, however goggles are recommended. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 200°F 4.b. Minimum storage temperature: None Bioremediation Agents 81 SHAMANTRA GREEN ------- 4.c. Optimum storage temperature range: 40°F to 140°F 4.d. Temperatures of phase separation and chemical changes: Stable V. SHELF LIFE >3 years when stored in sealed silos, polydrums, poly bags or totes. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Recommended Uses and Product Description Shamantra Green is recommended for use on water and near shoreline oil spills. Shamantra Green is a natural product made using humic acid. The product has been processed to have a strong affinity for collecting natural oils. The process makes applying and removing the product to/from the environment easy and safe. Water Applications For small scale spills on fresh or salt water, Shamantra Green can be broadcast directly onto the spill by hand or a hand held spreader. Agitation is not necessary when using Shamantra Green on small scale spills. Shamantra Green can also be used in booms, sacks, and pillows. For large spills on fresh or salt water, Shamantra Green can be deployed into the spill using an air or water stream. Shamantra Green will remove oils and other hazardous hydrocarbon based materials from both salt and fresh water very effectively using an encapsulation process on the spilled oil. Once encapsulated into the carbon matrix of Shamantra Green, the spilled oil will not leach out, even under pressure. The humic acid then acts as a nutrient to stimulate microbial activity and enhance the bioremediation of the spilled oil. Any encapsulated residue can be removed from the water with hand vacuums, vacuum barges, commercial nets, centrifuges, etc. Encapsulated materials can be sent to landfill or used as a fuel source for generating heat ensuring that any material disposed of is in accordance with all applicable federal, state, and local regulations. Shoreline Applications For spills on shorelines, Shamantra Green would be applied in the same manner and ratios as with the water applications. The product can also be applied by sand-blasting equipment, fire hoses or pneumatic spreading equipment. Agitation is not necessary for most applications. To recover encapsulated oil or hazardous materials from spills on land, the encapsulated product can be collected and removed efficiently and effectively using a variety of manual and mechanical methods including picking up by hand, using brooms, rakes and shovels to remove and pick up encapsulated petroleum waste product. Mechanical means include using hand held vacuums, portable vacuum units, and vacuum vehicles. Once the Shamantra Green has been saturated with oil or hazardous materials, it will not leach Bioremediation Agents 82 SHAMANTRA GREEN ------- the contaminants, even under pressure, so any encapsulated materials can be disposed of appropriately or used as a fuel source for generating heat ensuring that any material disposed of is in accordance with all applicable federal, state, and local regulations. Proper precautions, including testing as necessary to identify the characteristics of wastes encapsulated by Shamantra Green should be taken to determine the safe and legally required means of recovering, handling, storing, transporting, treating, recycling, or disposing of materials on land in accordance with all applicable federal, state, and local regulations. 2. Concentration/Application Rate: Shamantra Green is usually applied at a ratio of 1:5-1:30 to waste by weight to remediate light, medium, and heavy hydrocarbons. Shamantra Green can also be used very effectively on heavier crudes including Bunker C using the aforementioned application ratios. The specific ratio will depend on many factors including the composition of the waste, the ambient temperatures, pH of the contaminated water and age of the waste spill. Optimum application ratios should be determined on a case by case basis. 3. Conditions for Use: Shamantra Green initially behaves like a synthetic sorbent, then encapsulates the oil through a chemical and physical process. Once encapsulated, the spilled oil is captured within the pore matrix contained within the carbon structure. Shamantra Green is effective in all environments and under a broad range of weather conditions. Depending upon the age, viscosity, and composition of the spilled material, varying amounts of Shamantra Green may be required to obtain complete remediation. Any encapsulated residue can be recovered and disposed of in accordance with all applicable federal, state, and local regulations. VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL MEAN RED% MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 43,457 0 6,451 0 0 NUTRIENT 43,047 0 6,263 0 PRODUCT 43,153 0 6,262 0 Bioremediation Agents 83 SHAMANTRA GREEN ------- CONTROL 40,943 0 5,283 0 7 NUTRIENT 214 0 2,389 0 PRODUCT 9,859 0 1,338 0 CONTROL 39,066 10.1 4,429 31.3 28 NUTRIENT 76 99.8 685 89.1 PRODUCT 122 99.7 297 95.3 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 14.4% 0.0% 25.4% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS Nutrient Additive: No special requirements are required other than the product can be stored in dry conditions with an optimum storage temperature of 40°F to 140°F and a maximum storage temperature of 200°F. IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 84 SHAMANTRA GREEN ------- TECHNICAL PRODUCT BULLETIN: B-69 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: OCTOBER 13, 2011 "SUMP SAFE BIO-RECLAIM" I. NAME, BRAND, OR TRADEMARK SUMP SAFE BIO-RECLAIM Type of Product: Bioremediation Agent (Biological Additive/Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT F4 Environmental, Inc. P.O. BOX 2506 Stony Plain, Alberta, Canada T7Z 1X9 Mobile: (780) 238-2741 E-mail: marlin@f4environmental.ca (Mr. Marl in Rudolph) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Long Chain Reclaim 960 Boulder Blvd Stony Plain, Alberta, Canada T7Z 0E6 Phone: (780) 886-2024 Email: mmv shak@l creel aim. com (Mr. Mike Myshak) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required, however goggles are recommended. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 110°F maximum, must be used within 24 hours from constitution 4.b. Minimum storage temperature: 45°F 4.c. Optimum storage temperature range: 60°F to 90°F 4.d. Temperatures of phase separation and chemical changes: Stable V. SHELF LIFE The material must be used within 24-48 hours of constitution of the powdered bacteria portion in water. The dry material must be kept at -20°C and is stable for two years at this temperature. Once sent to the field, the material may be stored on ice for up to two weeks prior to constitution. Bioremediation Agents 85 SUMP SAFE BIO-RECLAIM ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Product may be applied by the usual methods. For smaller spills a drum pump with sprayer may be used, mixing with fresh water typically. The concentrate is used at 25:1 dilution rate with water and is typically applied at a rate of 6 gallons per cubic meter of soil. It is important that the soil be broken up into small clumps (rototilling is acceptable) to ensure effective application. The soil is left and biodegradation is expected to complete in approximately 12 weeks. Analysis using approved sampling procedures is performed to confirm biodegradation. For larger volume projects, any auger based soil homogenizer is employed to break up large clumps of soil, which are dug out from the contaminated area using a standard hoe. The broken up soil is taken up a conveyor and has the diluted concentrate (25:1) at a rate of 6 gallons per cubic meter of soil. Piles up to 20 feet high may be formed. The soil is left and biodegradation is expected to be complete in approximately 12-18 weeks. Analysis using approved sampling procedures is performed to confirm biodegradation. Proper safety rules must be employed to ensure that any holes dug out are not accessible to employees or unauthorized personnel. For oil spills on open water, it is recommended that a 25:1 dilution of the product be applied via spraying. In this way, the bacteria can contact the floating oil and immediately begin to form a bio-film. The spray would also be applied on any soil contaminated on banks, etc. It is important to ensure complete coverage of the water/oily surface and soil during spray application. Degradation will be visible visually and can be confirmed by Fats, Oil and Grease (FOG) analysis. For smaller, contained volumes of oily water (typically emulsified, white water), it is recommended that sufficient concentrate be added to the contaminated water such that it results in a 2.5% concentration of the concentrate in the contaminated water. Preferably, aeration can be performed, using even a small, fish tank aeration unit. Visual evidence of biodegradation should be apparent within one week or less and can be confirmed by FOG analysis. 2. Concentration/Application Rate: The concentrate is used at 25:1 dilution rate with water and is typically applied at a rate of 6 gallons per cubic meter of soil. 3. Conditions for Use: The product can be used in fresh or salt water and may be applied at temperatures between 40°F and 120°F. However, the product is most effective when applied at water temperatures between 70°F-90°F. Further, the product is effective on fresh spills or aged hydrocarbons. Note for preparation of the product to be applied while in the field: all components listed in the product are packaged as a complete unit and are applied as such. The microbial portion of the product is supplied in bags which are either drum (55 gallon) or pail (5 gallon) sizes. Fresh water, if available, is added to fill the bag (bags are placed in pails or open headed drums) to 55 gallon of 5 gallons respectively. Depending upon which of these are being constituted with water, a high-density polyethylene (HDPE) bottle with the appropriate quantity of surfactant is added into the container (bottles are labeled Bio-Reclaim Surfactant - Drum Size (or Pail Size)). In the same way, HDPE containers with appropriate amounts of sodium nitrite are added and are labeled Bio-Reclaim Salt - Drum Size (or Pail Size)). Bioremediation Agents 86 SUMP SAFE BIO-RECLAIM ------- VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL MEAN RED% MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 40770 0 5229 0 0 NUTRIENT 41329 0 5326 0 PRODUCT 40609 0 5384 0 CONTROL 37530 0 4824 0 7 NUTRIENT 21788 0 4634 0 PRODUCT 38354 0 5298 0 CONTROL 31456 22.8 3692 24.2 28 NUTRIENT 502 98.8 3052 42.7 PRODUCT 21356 47.4 3742 49.0 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 6.36% 33.00% 3.00% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of each component of the total formulation, other than microorganisms, by chemical name and percentage by weight: CONFIDENTIAL 2. Listing of all microorganisms by species and percentages of each species in the composition of the additive: CONFIDENTIAL 3. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 6-8 Temperature: 90°F Salinity: Not applicable 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: Bioremediation Agents 87 SUMP SAFE BIO-RECLAIM ------- pH: 4.8-9 Temperature: 59°F - 104°F Salinity: Not applicable 4. Special nutrient requirements: A combination of 70 percent live active yeast mixed with 30 percent fine ground corn cob is used as a nutrient. In a 55 gallon drum of concentrate, approximately 1.1 kg of this mix will be found (relative to the 1.1 kg, the actual bacteria represent the negligible mass of several grams). There are no storage requirements for the nutrient portion of the formula; however, as they are in a homogenous mixture with the bacteria, they must be stored as described in Part V of this bulletin. 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 88 SUMP SAFE BIO-RECLAIM ------- TECHNICAL PRODUCT BULLETIN: B-70 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: FEBRUARY 7, 2013 "WASTE AWAY®" I. NAME, BRAND, OR TRADEMARK WASTE AWAY® Type of Product: Bioremediation Agent (Biological Additive/Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT CXI (Chem-X International, LLC) 1100 East Sandy Lake Road Coppell, Texas 75019 Phone: (972) 471-7775 Fax: (972)393-2011 E-mail: dhowardcxi@outlook.com Website: www.cxinternational.com (Mr. David Howard) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Prime-Dirt 20810 Avenue 332 Woodlake, California 93286 Phone: (555) 787-7278 Fax:(555) 787-8560 E-mail: iames@prime-dirt.com Website: www.prime-dirt.com (Mr. James Henderson) Back-To-Nature Compost P.O. Box 190 5407 Slaton Highway Slaton, Texas 79364 Phone: (888) 282-2000 Phone: (806) 745-1170 E-mail: greg@backtonaturecompost.com or bi @backtonaturecompost.com Website: www.backtonaturecompost.com (Mr. Greg Schilling) Microbial Matrix 33935 Highway 99E, Suite B Tangent, Oregon 97389 Phone: (541) 967-0554 E-mail: lrogers@microbialmatrix.com Website: www.microbialmatrix.com (Ms. Lynn Rogers) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required; however, gloves and goggles are recommended. If eye or skin irritation Bioremediation Agents 89 WASTE AWAY® ------- occurs, flush with plenty of fresh water. If ingested, may cause nausea or vomiting, seek medical attention. Do not induce vomiting. In case of spills, disperse with water, treat like a surfactant or soap spill. 4.a. Maximum storage temperature: 100°F continuous, 120°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 50°F to 100°F 4.d. Temperatures of phase separation and chemical changes: Stable V. SHELF LIFE Two years when product remains in sealed bottles, poly drums, or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Product may be applied by any type of liquid delivery system (i.e., boom sprayers, spray pumps). For smaller spills a drum pump with sprayer may be used, mixing with fresh or salt water as required depending on the type and viscosity of oil being treated. Typically containment is not necessary. 2. Concentration/Application Rate: a. On heavy oils: use product directly on the spill, or up to approximately a 1:10 dilution ratio (product:water). Lighter oils will require a 1:10 to 1:30 product to water ratio. Warmer waters (greater than 78 °F) and/or good agitation during application will require less product. b. Lagoon application: 2 gallons per surface acre of lagoon or 16 ounces per 3,000 cubic feet. Maintain daily at 50 percent initial application. Use spray applicator for even distribution. c. Shoreline application: 1 gallon per 10 cubic yards of contaminated soil applied at 3 percent concentration. Maintain weekly with 50 percent initial application. Use spray applicator for even distribution. Till soil after application or use gravity fed drip system. 3. Conditions for Use: Effective in salt water or fresh water, with no limitations as to usage within optimum temperature parameters (application may be made at or above 35°F, with optimum above 48°F). Product may be used on any age crude and any type. Optimum salinity range is from fresh water to salt water of 110 ppt. Bioremediation Agents 90 WASTE AWAY® ------- VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 99715 0 11056 0 0 NUTRIENT 94558 0 10228 0 PRODUCT 98187 0 10270 0 CONTROL 54816 0 9690 0 7 NUTRIENT 48670 0 9329 0 PRODUCT 51534 0 6019 0 CONTROL 46847 53.0 6452 40.8 28 NUTRIENT 3581 96.2 6136 40.0 PRODUCT 776 99.2 4038 60.7 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient Product 6.41% 50.91% 49.95% b. Toxicity: Material Tested WASTE AWAY® No. 2 Fuel Oil WASTE AWAY® & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 552,762.06 96-hr 353,302.46 48-hr 10.22 96-hr 2.11 48-hr 12.54 96-hr 2.11 48-hr 11.87 96-hr 13.29 48-hr VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of each component of the total formulation, other than microorganisms, by chemical name and percentage by weight: CONFIDENTIAL 2. Listing of all microorganisms by species and percentages of each species in the composition of Bioremediation Agents 91 WASTE AWAY® ------- the additive: CONFIDENTIAL 3. Optimum pH, temperature, and salinity ranges for use of the additive: pH: 7.5, range 6.0 to 8.0 Temperature: 72°F, range 60°F to 60°F Salinity: 40 ppt, range 0 to 110 ppt 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 4.0-11.0 Temperature: 40°F - 125°F Salinity: 0-110 4. Special nutrient requirements: Not applicable 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 92 WASTE AWAY® ------- TECHNICAL PRODUCT BULLETIN: B-71 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: APRIL 7, 2014 "ACT TERRA FIRMA" (aka, ACT-TF) I. NAME, BRAND, OR TRADEMARK ACT TERRA FIRMA (aka, ACT-TF) Type of Product: Bioremediation Agent (Biological Additive/Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Franssen Enterprises, Inc. 511 N. McKinley Avenue Fort Lupton, CO 80621 Phone: (303) 833-5393 Fax:(303)833-2872 E-mail: actcleaners@comcast.net Website: www.actcleaners.com (Mr. Todd Franssen) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS American Cleaning Technologies, Inc. (ACT BioRemediation Products) 511 N. McKinley Avenue Fort Lupton, CO 80621 Phone: (303) 833-5393 Phone: (866) 919-2872 Fax:(303)833-2872 E-mail: actcl eaner s@ comcast. net Website: www.actcleaners.com (Mr. Todd Franssen) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Standard industrial hygiene ventilation practices should be used to control human exposures to this product. Respiratory protection equivalent to either N100 or the older HEPA filter (APR with a DFM (purple) cartridge) will provide adequate protection. 3. Skin and eye contact; protective clothing; treatment in case of contact: Recommendations are guidelines and may not apply to every situation. To prevent skin contact, standard work clothing and standard work or latex gloves will provide adequate protection. To prevent eye contact, standard safety glasses with side shields are recommended. 4.a. Maximum storage temperature: 48°C continuous, 60°C up to 5 days 4.b. Minimum storage temperature: -45°C Bioremediation Agents 93 ACT TERRA FIRMA ------- 4.c. Optimum storage temperature range: 4°C to 38°C 4.d. Temperatures of phase separation and chemical changes: Stable V. SHELF LIFE Store product in a dry area. If kept in a sealed container with desiccant bag the shelf life is 5 years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Apply ACT TERRA FIRMA directly to surfaces by broadcasting product with a scoop or grass seed drop spreader. DO NOT add fertilizers or nutrients. 2. Concentration/Application Rate: Hard Surface with Limited Permeability (e.g., concrete, asphalt, stone, etc.): Apply a small amount of ACT TERRA FIRMA with a scoop or grass seed drop spreader to the surface. Using a soft bristle broom spread ACT TERRA FIRMA over the surface. If desired results are not achieved within two weeks repeat application. DO NOT sweep or wash cleaner off. ACT TERRA FIRMA will dissipate over time. One pound covers approximately 100 square feet. DO NOT add fertilizers or nutrients. Prior to application, appropriate containment mechanisms should be used deployed to prevent runoff of the product/oil mixture. Permeable Surfaces (e.g.. packed sand, gravel, or soil; loose, bulk material that may be excavated and stockpiled for treatment): Apply ACT TERRA FIRMA product directly to surfaces by broadcasting product using a scoop or grass seed drop spreader over the contaminated area. Check the contamination levels every 15 days, reapplying as needed. Tilling may be needed for contamination 12 inches or deeper. One pound covers approximately 50 square feet. DO NOT add fertilizers or nutrients. Prior to application, appropriate containment mechanisms should be deployed to prevent runoff of the product/oil mixture. Applications to Water: ACT TERRA FIRMA is recommended for use in conditions where the water is not actively flowing. Apply to water surface at a rate of one pound over approximately a 200 square foot surface area. Using a scoop or a handheld broadcast spreader to ensure that ACT TERRA FIRMA is dispersed evenly. DO NOT add fertilizers or nutrients. Conditions for Use: Product usage is not affected by salinity. Water temperature range should be -2°C to 46°C and can be used on frozen water in temperatures as low as -65°C. ACT TERRA FIRMA is best used on contamination levels of 3% to 5% TPH. Contact Act BioRemediation Products for usage on higher contamination levels. Bioremediation Agents 94 ACT TERRA FIRMA ------- VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 29,969 0 9,018 0 0 NUTRIENT 29,102 0 8,582 0 ACT TERRA FIRMA 27,685 0 8,240 0 CONTROL 24,289 0 6,974 0 7 NUTRIENT 18,132 0 6,377 0 ACT TERRA FIRMA 2,614 0 3,306 0 CONTROL 18,909 36.9 4,426 50.8 28 NUTRIENT 1,465 94.9 5,609 34.6 ACT TERRA FIRMA 113 99.6 475 94.2 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control 0.0% Nutrient 17.0% ACT Terra Firma 9.7% b. Toxicity: Material Tested ACT TERRA FIRMA No. 2 Fuel Oil ACT TERRA FIRMA & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 223.60 96-hr 74.10 48-hr 4.24 96-hr 1.99 48-hr 2.61 96-hr 1.19 48-hr 12.25 96-hr 12.27 48-hr Bioremediation Agents 95 ACT TERRA FIRMA ------- VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of each component of the total formulation, other than microorganisms, by chemical name and percentage by weight: CONFIDENTIAL 2. Listing of all microorganisms by species and percentages of each species in the composition of the additive: CONFIDENTIAL 3. Optimum pH, temperature, and salinity ranges for use of the additive: pH: range 4.0 to 9.0 Temperature: range -20°C to 52°C Salinity: Freshwater 0 to 500 ppm; Ocean Saltwater 35,000 ppm 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 3.0 and 13.0 Temperature: -50°C and 65°C Salinity: Freshwater and 45,000 ppm 4. Special nutrient requirements: Not applicable. DO NOT add fertilizers or nutrients. 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES 1. Flash Point: NA 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: 0.8 g/cm3 5. pH: 7.0-12.0 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: NA 8. Additives: CONFIDENTIAL 9. Solubility: <5% (estimated) X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.13 Barium 1.30 Cadmium 0.077 Chromium 0.17 Copper NA Lead <0.25 Mercury <0.00010 Selenium 0.67 Silver <0.030 Bioremediation Agents 96 ACT TERRA FIRMA ------- Zinc NA Cyanide NA Chlorinated Hydrocarbons NA Bioremediation Agents 97 ACT TERRA FIRMA ------- TECHNICAL PRODUCT BULLETIN: B-72 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: APRIL 2, 2018 "PETROCLEAN™" I. NAME, BRAND, OR TRADEMARK PETROCLEAN™ Type of Product: Bioremediation Agent (Biological Additive/Microbiological Culture) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Green Earth Naturally, L L C. 2314 Ridgefield Street NE Roanoke, V A 24102 Phone: (540) 362-5636 Fax:(540)362-9447 E-mail: chale@greenearthnaturally.com Website: www.GreenEarthNaturally.com (Mr. Carroll Hale III) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Green Earth Naturally, L L C. 2314 Ridgefield Street NE Roanoke, V A 24102 Phone: (540) 362-5636 Fax:(540)362-9447 E-mail: chale@greenearthnaturally.com Website: www. GreenEarthN aturally. com (Mr. Carroll Hale III) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Use combination of general dilution ventilation and local exhaust ventilation to keep exposure as low as possible. 3. Skin and eye contact; protective clothing; treatment in case of contact: Prevent skin and eye contact by wearing appropriate personal protective equipment. If eye or skin irritation occurs, flush with plenty of fresh water. Coveralls or other suitable protective garments should be worn with suitable footwear for application and working conditions. Chemical safety goggles or glasses and impervious gloves are recommended. 4.a. Maximum storage temperature: below 120°F 4.b. Minimum storage temperature: above freezing 4.c. Optimum storage temperature range: 55°F to 100°F. Avoid storage in areas of extreme heat or extreme cold. Store in tightly closed containers, and away from children. 4.d. Temperatures of phase separation and chemical changes: Stable Bioremediation Agents 98 PETROCLEAN™ ------- V. SHELF LIFE Three to six months in sealed 1 gallon containers, 5 gallon buckets and 55 gallon drums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURE PETROCLEAN™ is effective in bioremediating petroleum contaminated soils and is not designed for use in open waters. There are no limitations to usage within optimum temperature parameters. 1. Application Method: a. Surficial spraying of PETROCLEAN™ may be applied by any type of liquid delivery system. i. Soils and gravels can be treated with PETROCLEAN™ using a conventional yard sprayer. Repetition may be needed. ii. PETROCLEAN™ can be applied to secondary containment areas, the key factor in cleaning the contaminated substrate, whether gravel or soil, is residence time for the microbes, moisture, and oxygen. b. Subsurface application can vary by location. Soil type becomes a contingent factor in dilution rates and method of application. When bioremediating soils, cleaning the contaminated substrate, whether gravel or soil, is affected by residence time for the microbes, moisture, and oxygen. i. For in-situ soils, mix PETROCLEAN™ with water to the desired concentration and dispense inoculated fluids in the subsurface, adjacent infrastructure, and the surface. ii. For ex-situ soils and longer term bioremediation projects, additional applications of nutrients and oxygen releasing compounds may be required to maintain or boost microbial activity. 2. Concentration/Application Rate: Rates will vary based upon the type of soil and amount of petroleum spilled, the extent of weathering, and other site-specific conditions, including soil profiles, proximity to surface waters and wells. Heavy petroleum compounds such as crude oil and bunker fuel, with a higher proportion of complex aliphatics, will require a higher concentration of PETROCLEAN™ than lighter petroleum compounds such as gasoline. a. Hydrocarbon types: PETROCLEAN™ can be applied on any hydrocarbon compound (including crude, diesel, gasoline, aviation fuel, bunker fuels, etc.) found in soils. b. Most frequent applications include any petroleum contamination around AST's and USTs and containment pits requiring rehabilitation. c. Concentration Rate: on heavy oils, apply PETROCLEAN™ directly on the spill area following absorption of free product, utilize a 1:10 dilution ratio (product to water). Lighter oils will require a 1:30 (product to water) dilution ratio. 3. Conditions for Use: Bioremediation slows at temperatures below 40°F. No limitations as to usage within optimum temperature parameters have been observed. a. Monitoring of dissolved oxygen levels is recommended. If needed, a mechanical aeration device should be deployed or the use of Oxygen Releasing Compounds (ORC) should be encouraged to maintain dissolved oxygen levels above 3 mg/L. b. Additional nutrients may be required to increase microbial activity over time if intrinsic nutrients are depleted. The application of 10% nitrogen, 10% phosphorus, and 10% Bioremediation Agents 99 PETROCLEAN™ ------- potassium fertilizer can be used in-situ or ex-situ as situations warrant to boost microbial activity and enhance co-metabolic digestion of petroleum. c. Prevent spill run-off from entering surface water bodies. d. Eliminate all source of ignition. e. Dispose of used absorbent materials according to all local, regional, and federal regulations. II. TOXICITY AND EFFECTIVENESS b. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 57,032 0 12,547 0 0 NUTRIENT 55,231 0 12,458 0 PETROCLEAN™ 58,148 0 12,141 0 CONTROL 55,126 0 12,091 0 7 NUTRIENT 47,951 0 11,599 0 PETROCLEAN™ 34,095 0 8,640 0 CONTROL 50,608 11.2% 10,766 14.2% 28 NUTRIENT 34,291 37.9% 9,574 23.1% PETROCLEAN™ 14,854 74.4% 4,711 61.1% Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient PETROCLEAN™ 7.83% 41.50% 60.93% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS 1. Listing of each component of the total formulation, other than microorganisms, by chemical name and percentage by weight: CONFIDENTIAL 2. Listing of all microorganisms by species and percentages of each species in the composition of the additive: CONFIDENTIAL Bioremediation Agents 100 PETROCLEAN™ ------- 3. Optimum pH, temperature, and salinity ranges for use of the additive: pH: range 6.3 to 7.3 Temperature: range 55°F to 100°F Salinity: 0 to 5% 3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 6.0 and 8.0 Temperature: >32°F and <120°F Salinity: no minimum and 10% 4. Special nutrient requirements: NA 5. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 101 PETROCLEAN™ ------- TECHNICAL PRODUCT BULLETIN: B-73 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: MAY 21, 2019 "ECOBIOCLEAN® 100 COSW" I. NAME, BRAND, OR TRADEMARK ECOBIOCLEAN® 100 COSW Type of Product: Bioremediation Agent (Microbiological Culture, Enzyme Additive, Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT JACOR, LLC 1000 Brown Street, Suite 208 Wauconda, II. 60084 Phone: (847) 865-3189 Fax: (847) 865-3287 E-mail: info@ecobioclean.com or ianetangel@ecobioclean.com Website: www.ecobioclean.com (Dr. J an el Angel, CEO, Inventor) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS JACOR, LLC 1000 Brown Street, Suite 208 Wauconda, II. 60084 Phone: (847) 865-3189 Fax: (847) 865-3287 E-mail: info@ecobioclean.com or ianetangel@ecobioclean.com Website: www.ecobioclean.com (Dr. J an el Angel, CEO, Inventor) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Special ventilation is not required. Use standard industrial hygiene ventilation practices. Use of a dust mask for respiratory protection in line with NIOSH standards such as N100 (3M) quality or comparable products will provide adequate protection from non-oil-based dust particles. 3. Skin and eye contact; protective clothing; treatment in case of contact: To protect skin from contact, standard work clothing and standard work or latex gloves will provide adequate protection. In case of skin contact, wash with soap and water. To prevent eye contact, standard safety glasses with side shields are recommended. In case of eye contact, flush with plenty of water. 4.a. Maximum storage temperature: 120°F (48°C) continuous up to 5 days. 4.b. Minimum storage temperature: 32°F (0.00 °C) 4.c. Optimum storage temperature range: 40°F (4.44°C) to 120°F (48°C). Bioremediation Agents 102 ECOBIOCLEAN® 100 COSW ------- 4.d. Temperatures of phase separation and chemical changes: Stable V. SHELF LIFE Store product in a dry area. If kept in sealed container such as drums or totes (as delivered) at temperatures below 100 °F, shelf life is 4-5 years. VI. RECOMMENDED APPLICATION PROCEDURE 4. Application Method: ECOBIOCLEAN® 100 COSW is a multi-faceted bioremediation product that may be applied directly in powder form or diluted with non-chlorinated water to initiate degradation of crude oil (hydrocarbons) at the source of contamination such as on shorelines, vegetation, or land. For powder treatment, apply directly to contamination site via crop dusting implements, farm fertilizer apparatus, and planes for larger areas. For smaller spills where powder form is desired, use fertilizer distributors, hand sprinklers, or other dry nutrient delivery system. For liquid applications and after dilution, apply with any commercially available spray apparatus, such as hand held tanks, back packs, and large mixing tanks with pumping devices. In addition, ECOBIOCLEAN® 100 COSW may be applied via educator systems from vessels, fire trucks, or any other appropriately outfitted vehicle. Spraying/applying to the outer edges of contamination site first and then working inward will help control spreading of spill. 5. Concentration/Application Rate: Concentration rates will vary based upon the type of crude oil spilled, the type of substrate and the amount of contamination spilled, the weathering process, and environmental conditions. ECOBIOCLEAN® 100 COSW contains billions of active hydrocarbon consuming microbes (MC) per gram along with a supporting proprietary complex of nutrients (NA) and enzymes (EA), which together are bio-catalyzing elements that stimulate bioremediation. ECOBIOCLEAN® 100 COSW may be applied to shorelines or land in full strength powder form or diluted using native water supplies as required depending upon the location of environmental contamination (do not use municipal/chlorinated water for mixing). Product may be applied immediately after mixing or within 12 hours via hoses or other spray devices or systems. Dilute 1:10 to 1:30(1 pound product to 10-30 gallons native water) depending upon the type of contamination. For example, heavy petroleum compounds such as crude oil or bunker fuel will require higher dose of ECOBIOCLEAN® 100 COSW and lighter petroleum compounds will require less. Nutrient additives are not necessary. Within minutes ECOBIOCLEAN® 100 COSW should begin to penetrate the molecular walls initiating bioremediation. ECOBIOCLEAN® 100 COSW provides an inoculum that insures bacterial colonies consume hydrocarbons throughout the remediation process. Within 3-7 days, there should be a noticeable reduction of crude oil contamination and odor while population of microbial strains continue to proliferate. Weathered oils may require longer treatment times. Diluted product can be sprayed from a boat or aircraft to degrade surface oils on soil, beach/sand surface, or vegetation. When dry application is preferred, such as in or around UST/AST and containment pits, ECOBIOCLEAN® 100 COSW can be applied via powder distribution implements as with seeding/fertilizing equipment or dry sprayers and then tilled for more complete distribution of product to contaminant. Be certain to cover the entire contaminated area for thorough treatment starting with perimeter and working to center. Product will quickly begin to break the hydrocarbon structure into organic nutrient substances that aquatic Bioremediation Agents 103 ECOBIOCLEAN® 100 COSW ------- and ground life can feed upon. In some circumstances (such as above) tilling of the ground is advisable to insure higher oxygenation and that product is reaching offending chemical. Within hours, odors should be greatly reduced, as may the hydrocarbon bonding properties helping to prevent adhesion to vegetation, rocks, soil/earth, and wildlife. (Use only non- chlorinated water for dilution.) Estimate area needing treatment. Use 1 pound of product (dilute 1:10 to 1:25 product to gallons of water) per cubic yard of heavy crude oil spilled, or 10 pounds of product per acre of land depending upon the oil type, penetration depth and concentration. Heavier oils may need greater biomass than lighter oils or fuels. 6. Conditions for Use: Product is effective in salt water or fresh water ecosystems including marshlands, rocks, vegetation, sand, and soil (shorelines/land) with no limitations as to usage within temperature parameters above 35°F and below 100°F. For greater immediate activity, water temperature for optimal mixing is between 60-80°F, though you may mix with warmer or colder non-chlorinated water between 45-105°F if need exists. Water salinity is not a factor as ECOBIOCLEAN® 100 COSW works well with all forms of water. Weathered crude/hydrocarbon contamination or tar-like substances may need to be agitated or tilled/cut for shorter remediation time prior to or with application. For heavy oils use product directly on the spill or up to approximately a 1:10 dilution ratio (1 pound product to 10 gallons of water). Lighter oils would require a 1:10 to 1:30 product to water dilution ratio. In warmer waters and in good agitation during application less product may be required. ECOBIOCLEAN® 100 COSW will work more quickly when adequate oxygen levels exist at contamination site but is viable wherever microbial life can be sustained. II. TOXICITY AND EFFECTIVENESS c. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL MEAN RED% MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 65064 0 7360 0 0 NUTRIENT 57799 0 6452 0 PRODUCT 59661 0 6731 0 CONTROL 60375 0 5788 0 7 NUTRIENT 47685 0 5309 0 PRODUCT 33684 0 3888 0 CONTROL 55425 14.80 5874 20.20 28 NUTRIENT 27944 57.10 4041 45.10 Bioremediation Agents 104 ECOBIOCLEAN® 100 COSW ------- PRODUCT 6479 90.00 1789 75.70 Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient ECOBIOCLEAN® 100 COSW 8.90% 51.50% 60.93% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS Microbiological Cultures: 1. Listing of each component of the total formulation, other than microorganisms, by chemical name and percentage by weight: CONFIDENTIAL 2. Listing of all microorganisms by species and percentages of each species in the composition of the additive: CONFIDENTIAL 3. Optimum pH, temperature, and salinity ranges for use of the additive: pH: range 6.5 to 7.5 Temperature: range 75°F to 85°F Salinity: 0.5 to 15.0% 4. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: pH: 5.5 and 11.0 Temperature: 32°F and 120°F Salinity: maximum permissible salinity is up to 20% by solution 5. Special nutrient requirements: NA 6. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative Enzyme Additives: 1. Listing of each component of the total formulation, other than enzymes, by chemical and percentage by weight: CONFIDENTIAL 2. Enzyme(s): CONFIDENTIAL 3. International Union of Biochemistry (I.U.B.) number(s): CONFIDENTIAL 4. Source of enzyme: CONFIDENTIAL 5. Units: No less than 1% and no more than 25% by weight. 6. Specific Activity: CONFIDENTIAL 7. Optimum Conditions: pH: 7.0 Temperature: CONFIDENTIAL Bioremediation Agents 105 ECOBIOCLEAN® 100 COSW ------- Salinity ranges for use of the additive: CONFIDENTIAL Minimum and maximum pH: 4.5 to 8.5 Minimum and maximum temperature: CONFIDENTIAL Minimum and maximum salinity levels above or below which the effectiveness of the additive is reduced to half its optimum capacity: CONFIDENTIAL 8. Enzyme shelf life: Up to 5 years if unopened and stored properly 9. Enzyme optimum storage conditions: Low moisture environment at temperatures between 40°F and 115°F Nutrient Additives: 1. Listing of each component of the total formulation by chemical name and percentage by weight: CONFIDENTIAL 2. Nutrient additive optimum storage conditions: Store product in sealed containers and dry area at temperatures between 40°F and 120°F. IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 106 ECOBIOCLEAN® 100 COSW ------- TECHNICAL PRODUCT BULLETIN: B-74 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: AUGUST 6, 2020 "SPILL GENIE™ 3T" (aka, SG3T) I. NAME, BRAND, OR TRADEMARK SPILL GENIE™ 3T (aka, SG3T) Type of Product: Bioremediation Agent (Biological Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Product Owner/Primary Contact: Product Manufacturer: Spill Genie, LLC Seatex Corporation 401 East Jackson Street (SunTrust Financial 445 Texas Highway 36 Center), Suite 2340 Rosenberg, TX 77417 Tampa, FL 33602 Phone: (713) 357-5300 Phone: (352) 515-3861 E-mail: kaimes@seatexcorp.com Fax: (813) 807-3036 Website: www.seatexcorp.com E-mail: rstotts@spill-genie.com (Mr. Kelly Aimes) Website: www.sg3t.com (Mr. Rick Stotts, President) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Spill Genie, LLC 401 East Jackson Street (SunTrust Financial Center), Suite 2340 Tampa, FL 33602 Phone: (352) 515-3861 Fax: (813) 807-3036 E-mail: rstotts@spill-genie.com Website: www.sg3t.com (Mr. Rick Stotts, President) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-Hazardous) 2. Ventilation: Recommended, ventilator in confined areas. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wear eye protection and impervious gloves. Wash face, hands and any exposed skin thoroughly after handling. If eye contact, wash eyes thoroughly for 15 minutes; including upper and lower lids and seek medical attention. For skin contact, irritation is possible, wash with soap and water for 15 minutes. If irritation persists, seek medical attention. 4.a. Maximum storage temperature: Below 95°F. 4.b. Minimum storage temperature: Above 32°F. 4.c. Optimum storage temperature range: 55°F to 90°F. Avoid storage in extreme heat and Bioremediation Agents 107 SPILL GENIE™ 3T ------- extreme cold. 4.d. Temperatures of phase separation and chemical changes: Stable within storage temperature ranges. V. SHELF LIFE One year in the original unopened container, as delivered, under optimum storage conditions. It is not recommended to store in open containers. Unused product stored in a properly sealed or air tight container will have a diminished shelf life of less than one year. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Surficial spraying of Spill Genie™ 3T may be applied by a conventional liquid delivery system used in the bioremediation industry. a. Spill Genie™ 3T is designated for use on soils, sandy or gravel applications. In-situ and situ application can vary based on soil and surface composition. Spill Genie™ 3T is pre-mixed into water and sprayed directly onto the hydrocarbon contaminants on soils, sandy or gravel areas. Spill Genie™ 3T should be applied using recommended dilution rates and utilizing a conventional sprayer or water dispensing cannon (recommend application above 35°F, with optimum above 48°F). Reapplication may be required to achieve desired results. b. When bioremediating contaminated substrate, whether sand, gravel or soil, additional applications of nutrients, oxygen releasing compounds and or aeration may be required to maintain or boost microbial activity. 2. Concentration/Application Rate: a. Typical dilution is 1 gallon of Spill Genie™ 3T with 9 gallons of water (approximately 1:10 dilution ratio, product to water). For lighter hydrocarbons, a dilution ratio of up to 1:30, product to water). Apply 0.5 gallons of stock solution of Spill Genie™ 3T to one cubic yard of contaminated soil. Agitate to slurry by mixing thoroughly with contaminated soil. Application rate may vary due to level of hydrocarbon contamination or type and density of treatable substrate. b. Hydrocarbon types: Spill Genie™ 3T can be applied on hydrocarbon compounds including, but not limited to, crude, diesel, gasoline, aviation fuel, light oils, and bunker fuels. c. Aged or asphaltic contaminants may be more resistant to remediation efforts and may require multiple applications. d. Application rates of Spill Genie™ 3T may vary widely based on unknown extent and depth of contamination. 3. Conditions for Use: a. Most frequent applications include petroleum contamination around ASTs and USTs (Above and Underground Storage Tanks) and containment pits requiring rehabilitation. b. Optimum application temperature of Spill Genie™ 3T is above 48°F. c. Aeration of treated medium is recommended as it will increase oxygen levels within the treated area allowing microbial reproductions and remediation activity to thrive. d. Additional nutrients may be required to increase microbial activity over time if intrinsic nutrients are depleted. An application of nitrogen, phosphorus, and Bioremediation Agents 108 SPILL GENIE™ 3T ------- potassium fertilizer can be used in-situ or situ to boost microbial activity and enhance co-metabolic digestion of petroleum. e. After treatment, solid asphaltic residue should be collected, removed from the site and disposed of in accordance with applicable local, state and federal regulations. Collection process and disposal of any excess washing solution, should comply with applicable local, state and federal regulations. f. Prevent spill run-off from entering surface and sub-surface water bodies. g. Expected results in TPH (Total Petroleum Hydrocarbon) reduction have been observed between 7 and 28 days. II. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL MEAN RED% TOTAL MEAN RED% 3 REPS/PROD ALKANES (ppm) 28 DAYS AROMATIC S (ppm) 28 DAYS CONTROL 46495 0 14656 0 0 NUTRIENT 43232 0 14090 0 PRODUCT 45979 0 13652 0 CONTROL 43141 0 12848 0 7 NUTRIENT 40276 0 12538 0 PRODUCT 33679 0 10128 0 CONTROL 37497 19.3% 12332 15.9% 28 NUTRIENT 22732 47.4% 10686 24.2% PRODUCT 14482 68.5% 7538 44.4% Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient SPILL GENIE™ 3T 14.5% 35.0% 57.0% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS Microbiological Cultures: Bioremediation Agents 109 SPILL GENIE™ 3T ------- 1. Listing of each component of the total formulation, other than microorganisms, by chemical name and percentage by weight: CONFIDENTIAL 2. Listing of all microorganisms by species and percentages of each species in the composition of the additive: CONFIDENTIAL 3. Optimum pH, temperature, and salinity ranges for use of the additive: CONFIDENTIAL 4. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity: CONFIDENTIAL 5. Special nutrient requirements: NA 6. Test results regarding the determination of the presence of the following: Salmonella: Negative Fecal coliform: Negative Shigella: Negative Staphylococcus Coagulase positive: Negative Beta hemolytic Streptococci: Negative Enzyme Additives: 1. Listing of each component of the total formulation, other than enzymes, by chemical and percentage by weight: CONFIDENTIAL 2. Enzyme(s): CONFIDENTIAL 3. International Union of Biochemistry (I.U.B.) number(s): CONFIDENTIAL 4. Source of enzyme: CONFIDENTIAL 5. Units: CONFIDENTIAL. 6. Specific Activity: CONFIDENTIAL 7. Optimum Conditions: CONFIDENTIAL 8. Enzyme shelf life: CONFIDENTIAL 9. Enzyme optimum storage conditions: CONFIDENTIAL Nutrient Additives: NA IX. PHYSICAL PROPERTIES NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 110 SPILL GENIE™ 3T ------- TECHNICAL PRODUCT BULLETIN: B-75 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 08, 2021 "GHG ORGANIC" I. NAME, BRAND, OR TRADEMARK GHG ORGANIC Type of Product: Bioremediation Agent (Nutrient Additive) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Bucheus Investments LLC 4320 NW 72nd Avenue Miami, FL 33166 Phone: +56-9-79128229 (WhatsApp Phone Number) Phone: (786) 521-0074 (Christian Alonso) Phone: (786) 436-9498 (Rene Mendoza) E-mail: asroiasl261@gmail.com (Mr. Alberto Rojas P., CEO) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Bucheus Investments LLC 4320 NW 72nd Avenue Miami, FL 33166 Phone: +56-9-79128229 (WhatsApp Phone Number) Phone: (786) 521-0074 (Cristian Alonso) Phone: (786) 436-9498 (Rene Mendoza) E-mail: asroiasl261@gmail.com (Mr. Alberto Rojas P., CEO) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Wearing masks with filter for fine dust under MESH 200 is recommended. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wear goggles for eye protection, impervious gloves, and normal work clothing. Contact may cause mild irritation. Wash face, hands, and any exposed skin thoroughly after handling. For eye contact, wash eyes thoroughly with clean water until irritation disappears. For skin contact and in case of redness or rash, wash the affected area with clean water until irritation disappears. If irritation persists, seek medical attention. 4.a. Maximum storage temperature: 140°F. 4.b. Minimum storage temperature: -10°F. 4.c. Optimum storage temperature range: -4°F to 104°F. 4.d. Temperatures of phase separation and chemical changes: Stable in powder form under all conditions. GHG ORGANIC in its natural states does not agglomerate or bind due to moisture. It does not require any type of additive to preserve its properties. Bioremediation Agents 111 GHG ORGANIC ------- V. SHELF LIFE Five years in open container; and four years in pressurized containers. Pressurized containers include portable extinguisher with N2 gas at 25 pounds working pressure 100 psi with metal anticorrosive valve made of 1/16-inch-thick carbon steel. Store in closed and dry places (e.g., containers, closed metal/wooden warehouses). Keep in manufacturers closed containers and store in height according to the resistance that bagged containers or pallets indicate, not to have a column with more than 2,000 pounds. Do not store volumes greater than 20,000 pounds in bulk in closed warehouses less than 1,000 yards from the vicinity of swamps of stagnant waters. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: GHG ORGANIC is a homogenous powder that is applied directly to oil contaminated solid surfaces (e.g., soil, sand, shorelines, and vegetation). Apply directly from container, product should not be diluted in water or mixed with other substances or solvents. Distribute GHG ORGANIC directly and uniformly on the spilled oil from containers (such as buckets and maxi bags) on the solid surface. For remote areas, apply using pressurized extinguishers with N2 gas (manual extinguishers from 2 pounds to 100 pounds) on solid surfaces. Means of application: a. From all terrain trucks, distribute GHG ORGANIC using 50-yard x 1 inch rubber hose of medium pressure (8 bar) coupled with: i. <5,000-pound tank mounted on pressurized pickup with N2 gas at 200 psi. ii. Compressed air 250 CFM and 8 bar working pressure mounted on a truck to pull product directly from open containers using a VENTURI so that GHG ORGANIC is projected onto the spilled oil on the solid surface. b. For difficult to access environments such as edges of islets and cliffs, recommend distributing GHG ORGANIC: i. From boats using 50-yard x 1-inch-long rubber hoses of medium pressure (8 bar) coupled to a compressed air compressor. 250 CFM and 8 bar working pressure is used to pull product directly from open containers using a VENTURI. ii. From planes and helicopters, GHG ORGANIC is available in plastic tanks that discharge the compound by gravity from gravitational sprinklers mounted on the discharge pipes outside the equipment. The application rate of the compound will be defined based on the surface affected by the spill. 2. Concentration/Application Rate: Applied at a ratio of 2 pounds product per square yard of oil; or 8,800 pounds of product per acre of oil. 3. Conditions for Use: Time of bioremediation is dependent upon oil density and ambient temperature. For light oils, bioremediation is 30 days. For heavy fuel oils, bioremediation is 90 days. A second application may be necessary in areas of accumulation. In case of oil seepage to the subsoil due to old spills in permeable soils and to accelerate the bioremediation process, the manufacturer recommends removing the contaminated soil and mixing GHG ORGANIC using vibratory screens and industrial blending machines. Bioremediation Agents 112 GHG ORGANIC ------- VII. TOXICITY AND EFFECTIVENESS a. Effectiveness: Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994: Summary Data Table DAYS PRODUCT TOTAL RED% TOTAL MEAN RED% MEAN 3 REPS/PROD ALKANES 28 AROMATIC S 28 (ppm) DAYS (ppm) DAYS CONTROL 39682 0 5055 0 0 NUTRIENT 38370 0 5578 0 PRODUCT 38358 0 4699 0 CONTROL 38159 0 4797 0 7 NUTRIENT 36956 0 5575 0 PRODUCT 31488 0 4270 0 CONTROL 37517 5.5% 4871 3.6% 28 NUTRIENT 29986 21.8% 4822 13.5% PRODUCT 13599 64.7% 3074 34.6% Results of Gravimetric Analysis: Percentage (%) Decrease in Weight of Oil on Day 28 Control Nutrient GHG ORGANIC 7.0% 15.1% 52.5% b. Toxicity: NA VIII. MICROBIOLOGICAL ANALYSIS The product is a nutrient additive and does not contain microbiological cultures or enzyme additives. 1. Listing of each component of the formulation by chemical name and percentage by weight: CONFIDENTIAL 2. Optimum storage conditions: Temperature: -4.0°F to 104°F IX. PHYSICAL PROPERTIES NA Bioremediation Agents 113 GHG ORGANIC ------- X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS NA Bioremediation Agents 114 GHG ORGANIC ------- DISPERSANTS: TECHNICAL NOTEBOOK BULLETINS 115 ------- TECHNICAL PRODUCT BULLETIN #D-1 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 10, 1978 REVISED LISTING DATE: DECEMBER 18, 1995 "COREXIT™ EC9527A" I. NAME, BRAND, OR TRADEMARK COREXIT™ EC9527A Type of Product: Dispersant (formerly COREXIT 9527) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: COREXIT™ EC9527A is not classified as flammable by either DOT or IMO regulations. 2. Ventilation: Avoid prolonged breathing of vapors. Use with ventilation equal to unobstructed outdoors in moderate breeze. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye contact. In case of eye contact, immediately flush eyes with large amounts of water for at least 15 minutes. Get prompt medical attention. Avoid contact with skin and clothing. In case of skin contact, immediately flush with large amounts of water, and soap if available. Remove contaminated clothing, including shoes, after flushing has begun. If irritation persists, seek medical attention. For open systems where contact is likely, wear long sleeve shirt, chemical resistant gloves, and chemical protective goggles. 4.a. Maximum storage temperature: 170°F 4.b. Minimum storage temperature: -30°F 4.c. Optimum storage temperature range: 40°F to 100°F Dispersants 116 COREXIT™ EC9527A ------- 4.d. Temperatures of phase separations and chemical changes: COREXIT™ EC9527A is not adversely affected by changes in storage temperature unless evaporation is allowed to occur. V. SHELF LIFE The shelf life of unopened drums of COREXIT™ EC9527A is unlimited. Containers should always be capped when not in use to prevent contamination and evaporation of solvents. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: COREXIT™ EC9527A is most effectively applied by aircraft, however, application with boat spray booms, boat fire monitors, and by hand held sprayers and back packs has been successfully done on a number of spills and trials. Aerial Spraying - Aircraft provide the most rapid method of applying dispersants to an oil spill and a variety of aircraft can be used for spraying. For aerial spraying, COREXIT™ EC9527A is applied undiluted. Typical application altitudes of 30 to 50 feet have been used, although higher altitudes may be effective under certain conditions. Actual effective altitudes will depend on the application equipment, weather and aircraft. Careful selection of spray nozzles is critical to achieve desired dose levels, since droplet size must be controlled. Many nozzles used for agricultural spraying are of low capacity and produce too fine a spray. A quarter-inch open pipe may be all that is necessary if the aircraft travels at 120 mph (104 knots) or more, since the air shear at these speeds will be sufficient to break the dispersant into the proper sized droplets. Boat Spraying - COREXIT™ EC9527A may be applied by workboats equipped with spray booms mounted ahead of the bow wake or as far forward as possible. The preferred and most effective method of application from a workboat is to use a low-volume, low-pressure pump so the chemical can be applied undiluted. Spray equipment designed to provide a five to ten percent diluted dispersant solution to the spray booms can also be used. COREXIT™ EC9527A should be applied as droplets, not fogged or atomized. Natural wave or boat wake action usually provides adequate mixing energy to disperse the oil. Recent tests have indicated that a fire monitor modified with a screen cap for droplet size may also be useful for applying COREXIT™ EC9527A. Due to the increased volume output and the greater reach of the fire monitor, significantly more area can be covered in a shorter period of time. System Calibration - Spray systems should be calibrated at temperatures anticipated to insure successful application and dosage control. 2. Concentration/Application Rate: A treatment rate of about 2 to 10 U.S. gallons per acre, or a dispersant to oil ratio of 1:50 to 1: 10 is recommended. This rate varies depending on the type of oil, degree of weathering, temperature, and thickness of the slick. 3. Conditions for Use: As with all dispersants, timely application ensures the highest degree of success. Early treatment with COREXIT™ EC9527A, even at reduced treat rates, can reduce the "mousse" forming tendencies of the spilled oil. COREXIT™ EC9527A is useful on oil spills in salt water. Dispersants 117 COREXIT™ EC9527A ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) COREXIT™ EC9527A Menidia beryllina 14.57 96-hr Mysidopsis bahia 24.14 48-hr No. 2 Fuel Oil Menidia beryllina 10.72 96-hr Mysidopsis bahia 16.12 48-hr COREXIT™ EC9527A & Menidia beryllina 4.49 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 6.60 48-hr Reference Toxicant (DSS) Menidia beryllina 7.07 96-hr Mysidopsis bahia 9.82 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (%) Prudhoe Bay Crude 37.4 South Louisiana Crude 63.4 Average of Prudhoe Bay and South Louisiana Crudes 50.4 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 163°F 2. Pour Point: < - 40°F 3. Viscosity: 160 cSt at 32°F 4. Specific Gravity: 0.98 - 1.02 5. pH: 6.1 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: Water, Propylene Glycol, 2-Butoxyethanol 8. Additives: CONFIDENTIAL 9. Solubility: Complete Dispersants 118 COREXIT™ EC9527A ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) <0.005 <0.01 1.0 <0.2 <0.1 <0.003 <0.1 0.1 <0.01 <0.01 Dispersants 119 COREXIT™ EC9527A ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #D-2 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: APRIL 22, 1985 REVISED LISTING DATE: JANUARY 26, 1996 "NEOS AB3000" I. NAME, BRAND, OR TRADEMARK NEOS AB3000 Type of Product: Dispersant (Hydrocarbon Solvent Based) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT NEOS Company Limited Daisan Kendai Building 1-2, 3-chome Isobedori Chuo-ku, Kobe, 651-0084 Japan Phone: updated information required E-mail: updated information required (Mr. T. Ishii, Manager) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS NEOS Company Limited Daisan Kendai Building 1-2, 3-chome Isobedori Chuo-ku, Kobe, Japan Phone: updated information required E-mail: updated information required (Mr. T. Ishii, Manager) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: NEOS AB3000 is flammable; keep away from open flame. 2. Ventilation: Special ventilation is not required; however, natural ventilation is recommended. 3. Skin and eye contact; protective clothing; treatment in case of contact: Contact may cause skin and eye irritation. Goggles and rubber clothing are recommended during application. In case of contact with skin or eye, flush with copious amounts of fresh water. If severe, consult a doctor. 4.a. Maximum storage temperature: 158°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 50°F to 140°F 4.d. Temperatures of phase separations and chemical changes: Phase separation and chemical changes do not appear between the temperature range of 32°F to 158°F. V. SHELF LIFE 3/18/2016 7/27/2022 Dispersants 120 NEOS AB3000 ------- The shelf life is five (5) years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spray neat concentrate on the oil slick in atomized form by means of a manual pump, or spray with a pump system incorporating an ejector system for drawing concentrate from the drum or stock tank. For aerial application, use a spray boom with pressure nozzles or rotating atomizers mounted on helicopters or airplanes. 2. Concentration/Application Rate: The application rate is 65 gallons of dispersant per ton of oil. Five (5) to fifteen (15) parts of dispersant to suctioned water is recommended for ejector systems. For aerial application, 75 to 125 gallons per ton of oil is recommended. 3. Conditions for Use: NEOS AB3000 can be used in salt water. It is effective with crude and residual heavy oil. The dispersant is also effective at controlling volatile emissions from the oil. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) NEOS AB3000 Menidia beryllina 91.1 96-hr Mysidopsis bahia 33.0 48-hr No. 2 Fuel Oil Menidia beryllina 201.8 96-hr Mysidopsis bahia 11.5 48-hr NEOS AB3000 & Menidia beryllina 57.0 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 25.0 48-hr Reference Toxicant (DSS) Menidia beryllina 1.5 96-hr Mysidopsis bahia 9.3 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (%) Prudhoe Bay Crude 19.7 South Louisiana Crude 89.8 Average of Prudhoe Bay and South Louisiana Crudes 54.8 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: No flash point to 212°F Dispersants 121 NEOS AB3000 ------- 2. Pour Point: Less than 32°F 3. Viscosity: 30.7 cSt at 104°F 4. Specific Gravity: 0.924 at 59°F 5. pH: 8.0 (5wt % aq., at 77°F) 6. Surface Active Agents: Nonionic and Cationic surfactants 7. Solvents: Paraffin 8. Additives: None 9. Solubility: NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.1 Cadmium <0.1 Chromium 0.26 Copper <0.05 Lead 0.21 Mercury <0.001 Nickel 0.076 Zinc 1.1 Cyanide <0.05 Chlorinated Hydrocarbons <0.10 Dispersants 122 NEOS AB3000 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 3/22/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #D-3 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: FEBRUARY 23, 1988 REVISED LISTING DATE: JANUARY 26, 1996 "MARE CLEAN 200" I. NAME, BRAND, OR TRADEMARK MARE CLEAN 200 Type of Product: Dispersant (Solvent-Based) (formerly MARE CLEAN 505) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Ichinen Chemicals Co., Ltd Mita Twin Building, East Wing 8F 4-2-8 Shibaura, Minato-ku, Tokyo, Japan 108-0023 Phone: updated information required Fax: updated information required E-mail: updated information required (Mr. Tsuyoshi Imai) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Ichinen Chemicals Co., Ltd Mita Twin Building, East Wing 8F 4-2-8 Shibaura, Minato-ku Tokyo, Japan 108-0023 Phone: updated information required Fax: updated information required E-mail: updated information required (Mr. Tsuyoshi Imai) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: The flash point is 212°F @ 20°F 2. Ventilation: Is required. Use in closed room is not recommended. 3. Skin and eye contact; protective clothing; treatment in case of contact: Use protective goggles to avoid eye contact. In case of eye contact, wash immediately with plenty of water and consult with physician. 4.a. Maximum storage temperature: 122°F 4.b. Minimum storage temperature: 21°F 4.c. Optimum storage temperature range: 32°F to 86°F 4.d. Temperatures of phase separations and chemical changes: Phase separation does not relate to temperatures. Chemical changes may occur at temperatures above 194°F. Dispersants 123 MARE CLEAN 505 ------- V. SHELF LIFE The shelf life of MARE CLEAN 200 is 10 years when stored indoors. (Container will deteriorate before contents.) VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Sprinkle the dispersant on the oil spill, then 5-10 minutes later stir the surface intensively. For convenience, MARE CLEAN 200 may be diluted with water if desired. 2. Concentration/Application Rate: Use 53-66 gallons of MARE CLEAN 200 per ton of oil 3. Conditions for Use: The performance of MARE CLEAN 200 is not affected by water salinity. At temperatures below 40°F or in case of heavy crude oil spill, MARE CLEAN 200 should be used without dilution. MARE CLEAN 200 is an effective dispersant for any liquid hydrocarbon. VII. TOXICITY AND EFFECTIVENESS 1. Toxicity: Material Tested Species LC50 (DDm) MARE CLEAN 200 Menidia beryllina 1996.00 96-hr Mysidopsis bahia 938.00 48-hr No. 2 Fuel Oil Menidia beryllina 10.72 96-hr Mysidopsis bahia 16.12 48-hr MARE CLEAN 200 and Menidia beryllina 42.00 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 9.84 48-hr Reference Toxicant (SDS) Menidia beryllina 7.07 96-hr Mysidopsis bahia 9.82 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OILS Oil Effectiveness (%) Prudhoe Bay Crude 63.97 South Louisiana Crude 84.14 Average of Prudhoe Bay and South Louisiana Crudes 74.06 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 212°F@ 20°F 2. Pour Point: 14 @ 10°F 3. Viscosity: 2.4 @ 5 cSt at 104°F 4. Specific Gravity: 0.95 @ 0.03 at 77°F 5. pH: 7.7 @ 1.0 (10% solution) Dispersants 124 MARE CLEAN 505 ------- 6. Surface Active Agents: A mixture of sorbitan fatty acid esters, polysorbates, and polyoxyethylene fatty acid esters. 7. Solvents: Paraffinic hydrocarbons (CAS 74664-93-0) 8. Additives: None 9. Solubility: NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.50 Cadmium <0.100 Chromium <0.500 Copper <0.250 Lead <2.50 Mercury <0.0200 Nickel <0.250 Zinc 0.611 Cyanide <0.01 Chlorinated Hydrocarbons <0.10 Dispersants 125 MARE CLEAN 505 ------- TECHNICAL PRODUCT BULLETIN #D-4 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: APRIL 13, 1994 REVISED LISTING DATE: DECEMBER 18, 1995 "COREXIT™ EC9500A" I. NAME, BRAND, OR TRADEMARK COREXIT™ EC9500A Type of Product: Dispersant (formerly COREXIT 9500) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO - Non-flammable; DOT - Non-hazardous. 2. Ventilation: Use with ventilation equal to unobstructed outdoors in moderate breeze. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye contact. In case of eye contact, immediately flush eyes with large amounts of water for at least 15 minutes. Get prompt medical attention. Avoid contact with skin and clothing. In case of skin contact, immediately flush with large amounts of water, and soap if available. Remove contaminated clothing, including shoes, after flushing has begun. If irritation persists, seek medical attention. For open systems where contact is likely, wear long sleeve shirt, chemical resistant gloves, and chemical protective goggles. 4.a. Maximum storage temperature: 170°F 4.b. Minimum storage temperature: -30°F 4.c. Optimum storage temperature range: 40°F to 100°F 4.d. Temperatures of phase separations and chemical changes: None Dispersants 126 COREXIT™ EC9500A ------- V. SHELF LIFE The shelf life of unopened drums of COREXIT™ EC9500A is unlimited. Containers should always be capped when not in use to prevent contamination and evaporation of solvents. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: COREXIT™ EC9500A contains the same surfactants present in COREXIT™ EC9527A and a new improved oleophilic solvent delivery system. Aerial Spraying - Aircraft provide the most rapid method of applying dispersants to an oil spill and a variety of aircraft can be used for spraying. For aerial spraying, COREXIT™ EC9500A is applied undiluted. Typical application altitudes of 30 to 50 feet have been used, although higher altitudes may be effective under certain conditions. Actual effective altitudes will depend on the application equipment, weather and aircraft. Careful selection of spray nozzles is critical to achieve desired dose levels, since droplet size must be controlled. Many nozzles used for agricultural spraying are of low capacity and produce too fine a spray. A quarter-inch open pipe may be all that is necessary if the aircraft travels at 120 mph (104 knots) or more, since the air shear at these speeds will be sufficient to break the dispersant into the proper sized droplets. Boat Spraying - COREXIT™ EC9500A may also be applied by workboats equipped with spray booms mounted ahead of the bow wake or as far forward as possible. The preferred and most effective method of application from a workboat is to use a low-volume, low-pressure pump so the chemical can be applied undiluted. Spray equipment designed to provide a five to ten percent diluted dispersant solution to the spray booms can also be used. COREXIT™ EC9500A should be applied as droplets, not fogged or atomized. Natural wave or boat wake action usually provides adequate mixing energy to disperse the oil. Recent tests have indicated that a fire monitor modified with a screen cap for droplet size control may also be useful for applying COREXIT™ EC9500A. Due to the increased volume output and the greater reach of the fire monitor, significantly more area can be covered in a shorter period of time. System Calibration - Spray systems should be calibrated at temperatures anticipated to insure successful application and dosage control. Application at sub-freezing temperatures may require larger nozzle, supply lines and orifices due to higher product viscosity. 2. Concentration/Application Rate: A treatment rate of about 2 to 10 U.S. gallons per acre, or a dispersant to oil ratio of 1:50 to 1:10 is recommended. This rate varies depending on the type of oil, degree of weathering, temperature, and thickness of the slick. 3. Conditions for Use: As with all dispersants, timely application ensures the highest degree of success. Early treatment with COREXIT™ EC9500A, even at reduced treat rates, can also counter the "mousse" forming tendencies of the spilled oil. COREXIT™ EC9500A is useful on oil spills in salt water. Dispersants 127 COREXIT™ EC9500A ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) COREXIT™ EC9500A Menidia beryllina 25.20 96-hr Mysidopsis bahia 32.23 48-hr No. 2 Fuel Oil Menidia beryllina 10.72 96-hr Mysidopsis bahia 16.12 48-hr COREXIT™ EC9500A & Menidia beryllina 2.61 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 3.40 48-hr Reference Toxicant (SDS) Menidia beryllina 7.07 96-hr Mysidopsis bahia 9.82 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OILS Oil Effectiveness (%) Prudhoe Bay Crude 45.3 South Louisiana Crude 54.7 Average of Prudhoe Bay and South Louisiana Crudes 50.0 VIII. MICROBIOLOGICAL PROPERTIES NA IX. PHYSICAL PROPERTIES 1. FlashPoint: 181.4°F 2. Pour Point: <-71°F 3. Viscosity: 22.5 cSt at 104°F 4. Specific Gravity: 0.95 at 60°F 5. pH: 6.2 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: CONFIDENTIAL 8. Solvents: CONFIDENTIAL 9. Additives: None 10. Solubility: Miscible Dispersants 128 COREXIT™ EC9500A ------- X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.16 Cadmium ND Chromium 0.03 Copper 0.10 Lead ND Mercury ND Nickel ND Zinc ND Cyanide ND Chlorinated hydrocarbons ND Dispersants 129 COREXIT™ EC9500A ------- TECHNICAL PRODUCT BULLETIN #D-5 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: APRIL 22, 1999 "DISPERSIT SPC 1000™" (aka, SEACARE E.P.A. (ECOSPERSE™ POLLUTION ABATEMENT)) I. NAME, BRAND, OR TRADEMARK DISPERSIT SPC 1000™ (aka, SEACARE E.P.A. (ECOSPERSE™ POLLUTION ABATEMENT)) Type of Product: Dispersant (Water Based) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT U.S. Polychemical Corp. 584 Chestnut Ridge Road Chestnut Ridge, NY 10977 Phone: (845) 356-5530 Fax: (845)356-6656 E-mail: bruceg@uspoly.com (Mr. Bruce Gebhardt) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS U.S. Polychemical Corp. 584 Chestnut Ridge Road Chestnut Ridge, NY 10977 Phone: (845) 356-5530 Fax: (845)356-6656 E-mail: bruceg@uspoly.com (Mr. Bruce Gebhardt) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO: Non-flammable; DOT: Non-hazardous 2. Ventilation: None normally required. Adequate to maintain fume levels below the TLV. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid prolonged contact with skin and eyes. Flush eyes with plenty of water for at least 15 minutes. Get medical attention. Wear long sleeve shirt, chemical resistant gloves, and chemical protective goggles in case of exposure to mist. 4.a. Maximum storage temperature: 180°F 4.b. Minimum storage temperature: -25°F 4.c. Optimum storage temperature range: 40°F to 140°F 4.d. Temperatures of phase separations and chemical changes: None Dispersants 130 DISPERSIT SPC 1000™ ------- V. SHELF LIFE The shelf life of DISPERSIT SPC 1000™ is unlimited in unopened containers. Containers must be kept closed when not in use to prevent contamination. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: The dispersant may be applied by any conventional methods such as 1) aerial spraying and 2) boat spraying to accommodate weather conditions. 2. Concentration/Application Rate: A dispersant to oil ratio ranging from 1 part dispersant to 50 parts oil to 1 part dispersant to 10 parts oil; or an application rate of about 2-10 gallons (7.6 liters- 37.9 liters) per acre (4840 square meters) is suggested. These rates will be dependent on the type of oil, degree of weathering, temperature and extent of oil slick. 3. Conditions for Use: Timely application ensures the highest degree of successful dispersion of the oil spill. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) DISPERSIT SPC 1000™ Menidia beryllina 3.5 96-hr Mysidopsis bahia 16.6 48-hr No. 2 Fuel Oil Menidia beryllina 11.6 96-hr Mysidopsis bahia 11.7 48-hr DISPERSIT SPC 1000™ Menidia beryllina 7.9 96-hr & No. 2 Fuel Oil (1:10) Mysidopsis bahia 8.2 48-hr Reference Toxicant (SDS) Menidia beryllina 6.3 96-hr Mysidopsis bahia 11.7 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness Prudhoe Bay Crude 40 South Louisiana Crude 105 Average of Prudhoe Bay and South Louisiana Crudes 73 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM D-56-87: 208°F 2. Pour Point, ASTM D-97-87: <-20°C 3. Viscosity, ASTM D-445-88: 144CPS, @ 68°F 4. Specific Gravity, ASTM D-1298-85(90): 0.995, @ 68°F 5. pH, ASTM D-1293-84(90): 10.0 6. Surface Active Agents: Anionic and non-ionic, proprietary, surfactants 7. Solvents: Proprietary, non-petroleum based 8. Additives: None Dispersants 131 DISPERSIT SPC 1000™ ------- 9. Solubility in Water: Complete X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <1.00 Cadmium <2.00 Chromium <2.00 Copper <2.00 Lead <1.00 Mercury <0.04 Nickel <10.00 Zinc <2.00 Cyanide <2.00 Chlorinated Hydrocarbons <5.00 Dispersants 132 DISPERSIT SPC 1000™ ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #D-6 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: SEPTEMBER 20, 2000 "JD-109" I. NAME, BRAND, OR TRADEMARK JD-109 Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT GlobeMark Resources Ltd. 1312 Mill Creek Drive Sal ado, TX 76571 Mobile: (254) 231-2251 E-mail: fiddler656@gmail.com Website: www.globemarkresources.com (Ms. Joannie Docter) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS GlobeMark Resources Ltd. 1312 Mill Creek Drive Sal ado, TX 76571 Mobile: (254) 231-2251 E-mail: fiddler656@gmail.com Website: www.globemarkresources.com (Ms. Joannie Docter) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO - Nonflammable; DOT - Nonhazardous 2. Ventilation: Use with ventilation equal to unobstructed outdoors in a moderate breeze. 3. Skin and eye contact, protective clothing, treatment in case of contact: Avoid skin and clothing contact. If skin contact occurs, immediately wash with large amounts of soap and water (if possible). Remove any contaminated clothing and shoes. Launder before reusing. If irritation persists, seek medical assistance. For areas where contact is likely, wear long sleeve shirt, chemical resistant gloves, and chemical resistant goggles. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: - 4°F 4.c. Optimum storage temperature range: 32°F to 90°F 4.d. Temperatures of phase separations and chemical changes: None 3/22/2016 7/27/2022 Dispersants 133 JD-109 ------- V. SHELF LIFE The shelf life of unopened drums of JD-109 in unlimited. Containers should be capped when not being used to prevent contamination and evaporation. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: The most rapid and effective method of applying JD-109 to a oil spill is by spraying. Temperature ranges for application should not drop below 32°F or exceed 120°F. Aerial Spraying - Typical application altitudes of 30 to 50 feet are advised although higher altitudes may be used if conditions warrant. Spray nozzle should be about Vi inches in diameter flying at 104 knots or more to create enough water shear sufficient to break the dispersant into proper sized droplets. A V2 inch diameter nozzle may be needed for temperatures below 50°F. Boat Spraying - JD-109 can also be applied by workboats with spray booms mounted as far forward as possible of the bow or wake. The most effective application from a workboat is a low-volume, low-pressure pump. 2. Concentration/Application Rate: A treatment rate of about 2 to 10 US gallons (7.6 to 37.9 liters) per acre (4,840 square meters) or a dispersant to oil ratio of 1:50 to 1:10 is recommended. The rate may vary depending on the type of oil, degree of weathering, temperature and thickness of slick. 3. Conditions for Use: As with any oil related spill, timely application of a dispersant will ensure the highest degree of success. Timely treatment with JD-109, even at low application rates, can counter the "mousse" forming effect of the spilled oil. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested JD-109 No. 2 Fuel Oil JD-109 & No. 2 Fuel Oil (1:10) Reference Toxicant (SRT) LC50 (ppm) 1.90 96-hr 1.18 48-hr 96-hr 48-hr 9.35 3.13 Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL on Prudhoe Bay Crude South Louisiana Crude Average of Prudhoe Bay and South Louisiana Crudes 3.84 96-hr 3.51 48-hr 2.63 96-hr 8.06 48-hr Effectiveness (°/ 26 91 58.5 Dispersants 134 JD-109 ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM D3278-89: 93°C 2. Pour Point, ASTM D97-87: -19°C 3. Viscosity, ASTM D445-88: 202.9 cSt 4. Specific Gravity, ASTM D1298-85 (90): 1.02 5. pH, ASTM D1293-84 (90): 9.45 6. Surface Active Agents: Anionic and nonionic, proprietary, surfactants 7. Solvents: Proprietary, ester based 8. Additives: None 9. Solubility in Water: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <10 Cadmium <10 Chromium <10 Copper <10 Lead <10 Mercury <1 Nickel <10 Zinc <10 Cyanide <0.5 Chlorinated Hydrocarbons <1.4 Dispersants 135 JD-109 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 5/18/2006 7/27/2022 TECHNICAL PRODUCT BULLETIN #D-7 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: AUGUST 06, 2001 "JD-2000™" I. NAME, BRAND, OR TRADEMARK JD-2000™ Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT GlobeMark Resources Ltd. 1312 Mill Creek Drive Sal ado, TX 76571 Mobile: (254) 231-2251 E-mail: fiddler656@gmail.com Website: www.globemarkresources.com (Ms. Joannie Docter) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS GlobeMark Resources Ltd. 1312 Mill Creek Drive Sal ado, TX 76571 Mobile: (254) 231-2251 E-mail: fiddler656@gmail.com Website: www.globemarkresources.com (Ms. Joannie Docter) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO - Non-flammable. This product is not regulated by DOT when shipped domestically by land. 2. Ventilation: Use with ventilation equal to unobstructed outdoors in a moderate breeze. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid skin and clothing contact. If skin contact occurs, immediately wash with large amounts of soap and water (if possible). Remove any contaminated clothing and shoes. Launder before reusing. If irritation persists, seek medical assistance. For areas where contact is likely, wear long sleeve shirt, chemical resistant gloves, and chemical resistant goggles. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: -30°F 4.c. Optimum storage temperature range: 30°F to 90°F 4.d. Temperatures of phase separations and chemical changes: None Dispersants 136 JD-2000™ ------- V. SHELF LIFE The shelf life of unopened drums of JD-2000™ is unlimited. Containers should be capped when not being used to prevent contamination and evaporation. Opened container should be used within 1 year for optimal performance. Poly containers are recommended for storage near wet environments, i.e., ships, harbors, ports, etc. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: JD-2000™ is free of phosphates, aromatic chlorinated solvents, branched ethoxylated alcohols, and hydrotreated distillates. Optimum temperature for application is above 30°F. Aerial Spraying - Typical application altitudes of 30 to 50 feet are advised although higher altitudes may be used if conditions warrant. Spray nozzle should be about Vi inch in diameter flying at 104 knots or more to create enough air shear sufficient to break the dispersant into proper sized droplets. A V2 inch diameter nozzle may be needed for temperatures from 30°F to 30°F. Boat Spraying - JD-2000™ can also be applied by workboats with spray booms mounted as far forward as possible of the bow or wake. The most effective application from a workboat is a low-volume, low-pressure pump. 2. Concentration/Application Rate: JD-2000™ is an oil spill dispersant concentrate that may be diluted by 5 to 10 percent with water if needed. A treatment rate of about 2 to 10 U.S. gallons (7.6 to 37.9 liters) per acre (4,840 square meters) or a dispersant to oil ratio of 1:50 to 1:10 is recommended. The rate may vary depending on the type of oil, degree of weathering, temperature, and thickness of slick. 3. Conditions for Use: As with any oil related spill, timely (preferably within 48 hours) application of a dispersant will ensure the highest degree of success. Timely treatment with JD- 2000™, even at low application rates, can counter the "mousse" forming effect of the spilled oil. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) JD-2000™ Menidia beryllina 407.00 96-hr Mysidopsis bahia 90.50 48-hr No. 2 Fuel Oil Menidia beryllina 8.39 96-hr Mysidopsis bahia 2.58 48-hr JD-2000™ & No. 2 Fuel Oil Menidia beryllina 3.59 96-hr (1:10) Mysidopsis bahia 2.19 48-hr Reference Toxicant (SDS) Menidia beryllina 2.22 96-hr Mysidopsis bahia 10.50 48-hr Dispersants 137 JD-2000™ ------- 2. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (%) Prudhoe Bay Crude 60.4 South Louisiana Crude 77.8 Average of Prudhoe Bay and South Louisiana Crudes 69.1 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point (SW1010): 212°F 2. Pour Point (ASTM D97): -36°F 3. Viscosity (ASTM D445):65.2 cSt 4. Specific Gravity 60/60 (ASTM D287): 0.99 5. pH (EPA 150.1): 7.54 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: None 9. Solubility in Water: Dispersible in fresh and salt water. Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.24 Cadmium <0.10 Chromium <0.10 Copper <0.10 Lead 0.43 Mercury <0.10 Nickel <0.10 Zinc 0.11 Cyanide <0.20 Chlorinated Hydrocarbons <2.00 Dispersants 138 JD-2000™ ------- TECHNICAL PRODUCT BULLETIN #D-8 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 04, 2002 "NOKOMIS 3-F4" I. NAME, BRAND, OR TRADEMARK NOKOMIS 3-F4 Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Mar-Len Supply, Inc. 23159 Kidder Street Hayward, CA 94545 Phone: (510) 782-3555 Fax: (510) 782-2032 E-mail: marlensupply@vahoo.com (Mrs. Shirley Winter or Mr. Curt Winter) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Mar-Len Supply, Inc. 23159 Kidder Street Hayward, CA 94545 Phone: (510) 782-3555 Fax: (510) 782-2032 E-mail: marlensupplv@vahoo.com (Mrs. Shirley Winter or Mr. Curt Winter) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (water based) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of eye contact, flush with water; in case of skin contact, wash with water; and if swallowed, drink water to dilute and induce vomiting. 4.a. Maximum storage temperature: 212°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 50°F 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE 15 years or more if stored correctly in plastic drums. Dispersants 139 NOKOMIS 3-F4 ------- VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Application of the product may be made directly from 33 and 35 gallon drums (marketing sizes) by fitting the drum with a "T" connection and pumping fresh or salt water across the junction, which will pull the dispersant from the drum into the water stream and onto the oil spill. 2. Concentration/Application Rate: For heavy concentrations of crude or Bunker C oil, apply the product undiluted. Where lighter fractions of petroleum are involved, the product can be diluted up to one part dispersant to 30 parts water. 3. Conditions for Use: Effective in salt water, and can be used on water of any temperature. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) NOKOMIS 3-F4 Menidia beryllina 29.80 96-hr Mysidopsis bahia 32.20 48-hr No. 2 Fuel Oil Menidia beryllina 100.00 96-hr Mysidopsis bahia 72.70 48-hr NOKOMIS 3-F4 & Menidia beryllina 100.00 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 58.40 48-hr Reference Toxicant (DSS) Menidia beryllina 159.60 96-hr Mysidopsis bahia 267.70 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness Prudhoe Bay Crude 62.20 South Louisiana Crude 64.90 Average of Prudhoe Bay and South Louisiana Crudes 63.55 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: None 2. Pour Point: 28°F 3. Viscosity: 290 cps at 20°C (68°F) 4. Specific Gravity: 1.0065g/cc at20°C (68°F) 5. pH: 10.3 (at room temperature) 6. Surface Active Agents: Confidential 7. Solvents: None 8. Additives: None 9. Solubility: Completely water soluble Dispersants 140 NOKOMIS 3-F4 ------- X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.30 Cadmium <5.00 Chromium <10.00 Copper <10.00 Lead <10.00 Mercury <0.05 Nickel <10.00 Zinc <10.00 Cyanide <2.00 Chlorinated Hydrocarbons <1.00 Dispersants 141 NOKOMIS 3-F4 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #D-9 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JUNE 28, 2002 "BIODISPERS" I. NAME, BRAND, OR TRADEMARK BIODISPERS Type of Product: Dispersant (formerly PETROBIODISPERS) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Petrotech America Corporation 130 William Street, Suite 802 New York, NY 10038 Phone: (212)933-9071, ext. 7001 Fax:(877)226-4028 E-mail: Info@helpenvironmental.com (Mr. Lawrence Gallo) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Petrotech America Corporation Manufacturing Plant: 130 William Street, Suite 802 Clariant Corp. New York, NY 1003 8 Charlotte, NC Phone: (212)933-9071, ext. 7001 Fax: (877) 226-4028 E-mail: Info@helpenvironmental.com (Mr. Lawrence Gallo) H.E.L.P. Environmental 926 3rd Avenue Brooklyn, NY 11232 IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION I. Flammability: Non-flammable 2. Ventilation: Use general ventilation to minimize exposure to vapor or mist. 3. Skin and eye contact; protective clothing; treatment in case of contact: Skin contact - immediately flush with copious amounts of water. Remove and wash contaminated clothing and shoes. If irritation persists, see a doctor. Eye contact - may cause eye irritation. In case of contact, immediately flush eyes with plenty of water. If irritation persists, immediately see a doctor. Hygienic practices - wear safety glasses. Wear gloves in accordance with routine laboratory safety precautions. 7/19/2021 7/27/2022 Dispersants 142 BIODISPERS ------- 4.a. Maximum storage temperature: >70°C 4.b. Minimum storage temperature: -25°C 4.c. Optimum storage temperature range: 4.d. Temperatures of phase separations and chemical changes: No phase or chemical separation observed. V. SHELF LIFE The product has unlimited shelf life. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Recommended application is by aircraft, fireboat monitors or similar apparatus. 2. Concentration/Application Rate: Concentration varies with spilled material - Solvents at 5%, light oils at 10%, medium oils at 10%, and heavy oils at 10%. 3. Conditions for Use: Data is for water temperature of 40°F to 65°F. There are no known application restrictions. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) BIODIPSERS Menidia beryllina 13.46 96-hr Mysidopsis bahia 78.90 48-hr No. 2 Fuel Oil Menidia beryllina 12.42 96-hr Mysidopsis bahia 2.82 48-hr BIODIPSERS & Menidia beryllina 5.95 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.66 48-hr Reference Toxicant (SDS) Menidia beryllina 11.84 96-hr Mysidopsis bahia 21.81 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (%) Prudhoe Bay Crude 51.0 South Louisiana Crude 63.0 Average of Prudhoe Bay and South Louisiana Crudes 57.0 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM Method D56: 193°F 2. Pour Point, ASTM Method D97: - 26°F 3. Viscosity at 40°C, ASTM Method D445: Initial boil point 104.2°C, at 50 mL 109°C, at 70 mL 111°C, at 80 mL 113.7°C, final temperature 307.1°C) 4. Specific Gravity: 0.965 Dispersants 143 BIODISPERS ------- 5. pH: 7 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: Water 8. Additives: None 9. Solubility: Product is 100% soluble in water. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <2.50 Cadmium <0.75 Chromium <0.75 Copper <0.50 Lead <5.00 Nickel <1.20 Zinc <0.50 Cyanide 3.90* Chlorinated Hydrocarbons <5.00 *During the analysis of cyanide on sample #V202057-01 (Petrotech Dispersant) analyst encountered interferences due to the matrix of sample. Soapy residue created a false positive for cyanide. Sample showed no traces of cyanide. Value related to the soap film turbidity. Dispersants 144 BIODISPERS ------- TECHNICAL PRODUCT BULLETIN #D-10 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 26, 2002 "SEA BRAT #4" I. NAME, BRAND, OR TRADEMARK SEA BRAT #4 Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT B.R.A.T. Microbial Products Inc. 208 Cinnabar Bay Court League City, TX 77573 Phone: (713) 724-9226 E-mail: alabastercorp@gmail.com (Mr. John Sheffield) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS B.R.A.T. Microbial Products Inc. 208 Cinnabar Bay Court League City, TX 77573 Phone: (713) 724-9226 E-mail: alabastercorp@gmail.com (Mr. John Sheffield) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wear safety glasses or goggles, gloves, and rubber boots. Wash after each shift. Remove and wash contaminated clothing before reuse. No respiratory protection is required. Local exhaust is desirable. Mechanical exhaust is helpful in congested areas. Skin contact - flush with water. Seek medical attention if irritation persists. Eye contact - flush with water using eye cup or fountain for 15 minutes. Seek medical attention if irritation persists. Ingestion - seek medical attention. Inhalation - no medical attention is required with inhalation. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: NA 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE Indefinite when stored properly. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spray affected area with a high pressure pump. Always apply in Dispersants 145 SEA BRAT #4 ------- compliance with federal, state, and local laws. 2. Concentration/Application Rate: Dilution ratios of 1 part SEA BRAT #4 to 9 parts water for a 10 percent solution. 3. Conditions for Use: May be applied to the coastal waters of the U.S. It is designed for hydrocarbon spills on water temperatures between 50°F and 90°F. It is best applied with nozzle pressure of between 80 psi and 100 psi, with a direct hard spray and continuously moving the stream of water over the entire surface. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) SEA BRAT #4 Menidia beryllina 30.00 96-hr Mysidopsis bahia 14.00 48-hr No. 2 Fuel Oil Menidia beryllina 16.00 96-hr Mysidopsis bahia 14.00 48-hr SEA BRAT #4 & Menidia beryllina 23.00 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 18.00 48-hr Reference Toxicant (DSS) Menidia beryllina 1.14 96-hr Mysidopsis bahia 0.98 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL VENDOR LAB REPORT: Oil Effectiveness (%) Prudhoe Bay Crude 53.55 South Louisiana Crude 60.65 Average of Prudhoe Bay and South Louisiana Crudes 57.10 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM Method D56: 200°F 2. Pour Point, ASTM Method D97: 4°F 3. Viscosity (furol seconds): 380 at 77°F 4. Specific Gravity (g/cc): 0.994 at 70°F 5. pH: 9.45 6. Surface Active Agents: Surfactants 7. Solvents: Propylene glycol 8. Additives: None 9. Solubility: Soluble in all ratios. Dispersants 146 SEA BRAT #4 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) <0.05 <0.05 <0.05 <0.05 <0.05 <0.0002 <0.05 0.215 <0.05 <0.05 Dispersants 147 SEA BRAT #4 ------- TECHNICAL PRODUCT BULLETIN #D-11 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JANUARY 30, 2003 "FINASOL® OSR 52" (aka, SEACARE ECOSPERSE 52) I. NAME, BRAND, OR TRADEMARK FINASOL® OSR 52 (aka, SEACARE ECOSPERSE 52) Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT TotalEnergies Fluids 24 cours Michelet La Defense 10 92069 Paris La Defense Cedex France Phone: 011-33-1-41-35-30-48 United States: (713) 297-4651 24-hour Emergency Number: (713) 297-1996 E-mail: beniamin.swoboda@totalenergi es.com Website: www.specialfluids.totalenergies.com (Mr. Benjamin Swoboda) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Importer/U.S. Distributor TOTAL SPECIALTIES USA, INC. 1201 Louisiana Street, Suite 1800 Houston, TX 77002 Phone: (713)297-4651 Fax: (713)297-4689 E-mail: peter.egan@totalenergies.com Website: www.specialfluids.totalenergies.com (Mr. Peter Egan) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Keep well away from sources of ignition and heat. Avoid the accumulation of static electricity. Provide grounding. 2. Ventilation: Keep containers closed when not in use. Do not inhale vapors, fumes, or mists. In case of inhalation, take the person into fresh air. Ensure adequate ventilation is provided if there is any risk of vapors, mists, or aerosols forming. In the event of serious problems, call a doctor or summon medical assistance urgently. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wear appropriate long sleeve shirts, chemical resistant gloves and goggles. Avoid contact with skin and eyes. In case of contact, wash immediately with plenty of water. Avoid contact with clothing. In case of Dispersants 148 FINASOL® OSR 52 ------- contact, wash immediately and remove contaminated clothing. Prolonged and repeated contact with the skin may cause skin disorders. In case of ingestion, do not induce vomiting to prevent aspiration into the respiratory tract. 4.a. Maximum storage temperature: 65°C 4.b. Minimum storage temperature: -20°C 4.c. Optimum storage temperature range: 5 - 35°C 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE The shelf life of unopened drums of FINASOL® OSR 52 is potentially unlimited when the containers remain capped and sealed to prevent contamination and evaporation of solvents, and are stored in a place with stable temperatures and are unexposed to direct sunlight. After storage, stir the product and assure uniformity before use. Testing of FINASOL® OSR 52 is recommended every three years and then on a yearly basis to ensure it remains fit for its intended usage. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: FINASOL® OSR 52 is applied effectively by aircraft or from boats. It can also be applied by hand held sprayers as well as with backpack spray units. Spraying must not give too fine or atomized droplets as in fog. It must be done as moderately coarse droplets, with diameters in the range of 500 - 1000 m, whether application is by surface vessel, aircraft, or land-based equipment. 2. Concentration/Application Rate: Use FINASOL® OSR 52 from 1:5 to 1:50, according to the nature of the oil, its state of weathering, temperature, thickness of the slick, and other circumstances of the spill. A 1:10 ratio would correspond appreciatively to 26 gallons per ton of oil. Aerial spraying - FINASOL® OSR 52 is sprayed undiluted when applied from aircrafts, usually between 30 and 50 feet altitude, or at higher altitude in poor weather conditions. Boat spraying - FINASOL® OSR 52 is sprayed undiluted using a low-pressure system. Spraying equipment providing 5 to 10% dilution of FINASOL® OSR 52 can also be used. 3. Conditions for Use: Diluted application in low salinity water is not recommended. Use only receptacles, joints, pipes, etc. which are resistant to hydrocarbons. Do not spray at high pressure (> 3 bar). FINASOL® OSR 52 is designed to treat spills in salt water. Dispersants 149 FINASOL® OSR 52 ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) Menidia beryllina 11.66 96-hr Mysidopsis bahia 9.37 48-hr Menidia beryllina 5.95 96-hr Mysidopsis bahia 2.37 48-hr Menidia beryllina 5.40 96-hr Mysidopsis bahia 2.37 48-hr Menidia beryllina 8.54 96-hr Mysidopsis bahia 21.81 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL VENDOR LAB REPORT: FINASOL® OSR 52 No. 2 Fuel Oil FINASOL® OSR 52 & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) on Prudhoe Bay Crude South Louisiana Crude Average of Prudhoe Bay and South Louisiana Crudes Effectiveness 32.50 71.60 52.10 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM Method D-3278-89: 110°C 2. Pour Point, ASTM Method D-97-87: -27°C 3. Viscosity, ASTM Method D-445-88: 58.5 cSt 4. Specific Gravity, ASTM Method D-1298-85 (90): 1.01 5. pH, ASTM Method D-1293-84 (90): 8.57 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Dispersible in water. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Antimony <10.0 Arsenic <10.0 Barium <10.0 Cadmium <10.0 Chromium <10.0 Copper <10.0 Lead <10.0 Mercury <1.0 Dispersants 150 FINASOL® OSR 52 ------- Nickel Selenium Silver Zinc Cyanide Chlorinated Hydrocarbons <10.0 <10.0 <10.0 <10.0 <0.4 <4.4 Dispersants 151 FINASOL® OSR 52 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #D-12 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JANUARY 03, 2005 "SAF-RON GOLD" (aka, SF-GOLD DISPERSANT) I. NAME, BRAND, OR TRADEMARK SAF-RON GOLD (aka, SF-GOLD DISPERSANT) Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Sustainable Environmental Technologies Inc. 55 Ivan Allen Jr. Boulevard, Suite 850 Atlanta, GA 30308 Customer Service: Phone: (404) 946-3585 24-hour Emergency Number: Phone: updated information required E-mail: updated information required Website: updated information required (Mr. Bruce Richards) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Sustainable Environmental Technologies Inc. 55 Ivan Allen Jr. Boulevard, Suite 850 Atlanta, GA 30308 Customer Service: Phone: (404) 946-3585 24-hour Emergency Number: Phone: updated information required E-mail: updated information required Website: updated information required (Mr. Bruce Richards) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Special ventilation is not required. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment required; however, goggles are recommended. Skin contact - if irritation occurs flush with water; seek medical attention if irritation persists. Eye contact - flush with plenty of water; seek medical attention if irritation persists. 3/18/2016 7/27/2022 Dispersants 152 SAF-RON GOLD ------- 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 40 - 120°F 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE The shelf life is unlimited in unopened containers. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Sprayer, Boat, Aircraft. 2. Concentration/Application Rate: A dispersant to oil ratio ranging from 1:50 to 1:10 is recommended. For heavy high-viscosity oils - 8 gallons of SAF-RON GOLD will disperse approximately 70 gallons of crude oil or bunker C. Also for use with heavy high viscosity oils, SAF-RON GOLD can be used as a concentrate or diluted at a dispersant to water ratio of 1:10. For lighter oils, SAF-RON GOLD can be diluted at mixtures of 1:20 to 1:100. A recommended dispersant to water ratio of 1:40 can be used for most spills. Ratios are dependent upon type of oil and weather conditions. 3. Conditions for Use: Any applicable condition determined by authorities for dispersant use. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) SAF-RON GOLD Menidia beryllina 29.43 96-hr Mysidopsis bahia 63.00 48-hr No. 2 Fuel Oil Menidia beryllina 16.76 96-hr Mysidopsis bahia 5.93 48-hr SAF-RON GOLD Menidia beryllina 9.25 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 3.04 48-hr Reference Toxicant (SLS) Menidia beryllina 15.94 96-hr Mysidopsis bahia 9.83 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL VENDOR LAB REPORT: Oil Effectiveness (%) Prudhoe Bay Crude 84.80 South Louisiana Crude 53.80 Average of Prudhoe Bay and South Louisiana Crudes 69.30 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTMD-56: >100°C 2. Pour Point, ASTMD-97: -2.5°C 3. Viscosity @40°C, ASTM Method D-445: 1.42 cSt Dispersants 153 SAF-RON GOLD ------- 4. Specific Gravity @60°F/60°F, ASTM Method D-287: 1.014 5. pH: 8.8 6. Surface Active Agents: Proprietary blend of surface-active agents. 7. Solvents: None. 8. Additives: None. 9. Solubility: Fully water soluble. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.01 Cadmium <0.005 Chromium 0.140 Copper 0.324 Lead <0.005 Mercury <0.020 Nickel <0.005 Zinc 0.0671 Cyanide <0.20 Chlorinated Hydrocarbons <0.80 Dispersants 154 SAF-RON GOLD ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #D-13 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JUNE 16, 2005 "ZI-400" (aka, ZI-400 OIL SPILL DISPERSANT) I. NAME, BRAND, OR TRADEMARK ZI-400 (aka, ZI-400 OIL SPILL DISPERSANT) Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Z.I. Chemicals 340 S Lemon Avenue #5358 Walnut, CA 91789 Phone: updated information required E-mail: updated information required Website: www.zichemicals.com (Ms. Annie Mack) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Z.I. Chemicals 340 S Lemon Avenue #5358 Walnut, CA 91789 Phone: updated information required E-mail: updated information required Website: www.zichemicals.com (Ms. Annie Mack) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-Hazardous). 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required; however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40 - 120°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Unlimited in sealed polydrums of totes (as delivered). 3/18/2019 7/27/2022 Dispersants 155 ZI-400 ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: ZI-400 may be applied by the usual method of aerial or boat spraying. For smaller spills a drum pump with sprayer may be used, mixing with water as required depending on the type and viscosity of oil being treated. 2. Concentration/Application Rate: On heavy oils use ZI-400 directly on the spill, or up to approximately a 1:10 dilution ratio (product:water). Lighter oils will require a 1:10 to 1:30 product to water dilution ratio. Warmer waters (greater than 78°F) and/or good agitation during application will require less product. 3. Conditions for Use: No limitations as to usage within optimum temperature parameters (application may be made at or above 35°F, with optimum above 48°F). VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) ZI-400 Menidia beryllina 31.76 96-hr Mysidopsis bahia 20.96 48-hr No. 2 Fuel Oil Menidia beryllina 18.05 96-hr Mysidopsis bahia 2.66 48-hr ZI-400 Menidia beryllina 8.35 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 1.77 48-hr Reference Toxicant (SLS) Menidia beryllina 16.13 96-hr Mysidopsis bahia 27.80 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL VENDOR LAB REPORT: Oil Effectiveness (%) Prudhoe Bay Crude 50.10 South Louisiana Crude 89.80 Average of Prudhoe Bay and South Louisiana Crudes 69.90 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM D-56: >93°C 2. Pour Point, ASTMD-97: 12.6°F 3. Viscosity, ASTM D-445: 18.80 cSt @ 40°C 4. Specific Gravity, ASTM D-1298: 1.026 @ 60°F 5. pH, ASTM D-1293: 10.9 6. Surface Active Agents: Proprietary 7. Solvents: Proprietary 8. Additives: None. 9. Solubility: Miscible in oil, water, and solvents. Dispersants 156 ZI-400 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) <10 <10 <10 <10 <10 <1 <10 <10 <0.5 <1.0 Dispersants 157 ZI-400 ------- TECHNICAL PRODUCT BULLETIN #D-14 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 31, 2008 "NOKOMIS 3-AA" I. NAME, BRAND, OR TRADEMARK NOKOMIS 3-AA Type of Product: Water-Based Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Mar-Len Supply, Inc. 23159 Kidder Street Hayward, CA 94545 Phone: (510) 782-3555 Fax:(510)782-2032 E-mail: marlensupply@vahoo.com (Mrs. Shirley Winter or Mr. Curt Winter) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Mar-Len Supply, Inc. 23159 Kidder Street Hayward, CA 94545 Phone: (510) 782-3555 Fax:(510)782-2032 E-mail: marlensupplv@vahoo.com (Mrs. Shirley Winter or Mr. Curt Winter) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (water based) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of eye contact, flush with water; in case of skin contact, wash with water; and if swallowed, drink water to dilute and induce vomiting. 4.a. Maximum storage temperature: 160°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 32 - 140°F 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE In excess of 24 months or more if stored correctly in plastic drums. Dispersants 158 NOKOMIS 3-AA ------- VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Aerial applied dispersant - spray from an aircraft flying with a controllable speed at altitudes of 30 to 50 feet. Spray nozzles should be sized to cover an area using 5 gallons per surface acre. Spray from boat: NOKOMIS 3-AA can be applied by ships of workboat with spray booms mounted as far forward as possible. NOKOMIS 3-AA will generally be marketed in 55 gallon plastic drums. Application of the products may be made directly from the drum. By using a direct connection from pump to drum NOKOMIS 3-AA can be applied at full strength to the oil spill. The determination of whether to use NOKOMIS 3-AA at full strength or diluted with water must be determined by observations and evaluations made on-site at the oil spill. Portable engine powered centrifugal water pumps are a satisfactory means of moving the dispersant from the container to the spill's surface. Diesel-powered larger capacity pump may also be used. If the spill is confined to a small area, a hand-pump connected directly to the 55 gallon drum can be used. Hose diameters and lengths will relate to capacities required for the specific situation and distances from the pump to container and the spill. Fire hose has been successfully used, and with hand pumps small diameter hose is adequate. Fog nozzles on the dispersing end of the hose provide a fine spray of NOKOMIS 3-AA full strength or diluted as appropriate. Any type of hose nozzle can be used, but preferable one with the ability to produce a spray rather than a coarse stream. 2. Concentration/Application Rate: NOKOMIS 3-AA may be applied to oil spills at full strength, or diluted with sea water. Where large areas of water may be covered with heavy concentrations of crude or Bunker C oil, it may be advantageous to apply NOKOMIS 3-AA at full strength. Where lighter fractions of petroleum are involved it is possible that dilutions of up to one part NOKOMIS 3-AA to 30 parts water may be applicable. Approximately 5 gallons of NOKOMIS 3-AA can be used for one surface acre of oil spill. 3. Conditions for Use: Once NOKOMIS 3-AA is applied to the water's surface, to obtain the most efficient emulsification of the oil it is necessary to agitate and mix dispersant, oil, and water thoroughly. In open unconfined areas, the use of ship propellers has been determined a practical way of accomplishing this purpose. By passing over the spill area on a grid system, the vessel's propellers will churn the water, causing the needed mixing. For a large spill, two or more vessels may be needed to apply the product and agitate the water. In and around piers and similar confined areas it is necessary to apply the product from small boats, the shore, or pier itself. Where it is impossible or impractical to supply agitation with propellers of a vessel it is necessary to use pumps and a hose, applying salt water in the coarse stream and under sufficient pressure to cause surface turbulences and subsequent mixing. Dispersants 159 NOKOMIS 3-AA ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) NOKOMIS 3-AA Menidia beryllina 34.22 96-hr Mysidopsis bahia 20.16 48-hr No. 2 Fuel Oil Menidia beryllina 22.50 96-hr Mysidopsis bahia 11.07 48-hr NOKOMIS 3-AA & Menidia beryllina 7.03 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 5.56 48-hr Reference Toxicant (CUSO4) Menidia beryllina 5.36 96-hr Mysidopsis bahia 7.83 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (% Prudhoe Bay Crude 63.20 South Louisiana Crude 65.70 Average of Prudhoe Bay and South Louisiana Crudes 64.50 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: None 2. Pour Point: 25 °F 3. Viscosity: 72.3 sus at 100°F 4. Specific Gravity: 1.031 at 60°F 5. pH: 9.0 6. Surface Active Agents: Confidential 7. Solvents: Propylene glycol and Water 8. Additives: None 9. Solubility: Completely water soluble Dispersants 160 NOKOMIS 3-AA ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) <0.12 <0.25 <0.25 <0.25 <0.12 <0.0016 <0.25 <1.0 0.034 <0.10 Dispersants 161 NOKOMIS 3-AA ------- TECHNICAL PRODUCT BULLETIN #D-16 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 18, 2011 "ACCELL CLEAN® DWD" I. NAME, BRAND, OR TRADEMARK ACCELL CLEAN® DWD Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Advanced BioCatalytics Corporation 18010 Skypark Circle, #130 Irvine, California 92614-6456 Office Phone: (949) 771-0209 General E-mail: info@abiocat.com Website: www.abiocat.com Product Management: Mobile: (949) 981-6510 E-mail: cpodella@abiocat.com (Mr. Carl Podella) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Advanced BioCatalytics Corporation 18010 Skypark Circle, #130 Irvine, California 92614-6456 Office Phone: (949) 771-0209 General E-mail: info@abiocat.com Website: www.abiocat.com Product Management: Mobile: (949) 981-6510 E-mail: cpodella@abiocat.com (Mr. Carl Podella) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Combustible as defined by DOT and USCG. 2. Ventilation: Use in well ventilated areas. 3. Skin and eye contact; protective clothing; treatment in case of contact: Protective clothing is recommended. Avoid eye contact. In case of eye contact, immediately flush with large amounts of water for at least 15 minutes. Get prompt medical attention. Avoid direct contact with skin and clothing. In case of skin contact, immediately flush with large amounts of water. Remove contaminated clothing, including shoes, after flushing has begun. If irritation persists, seek medical attention. For open systems were contact is likely, wear long sleeve shirt, chemical resistant gloves, and protective chemical goggles. 4.a. Maximum storage temperature: 130°F/55°C Dispersants 162 ACCELL CLEAN® DWD ------- 4.b. Minimum storage temperature: 30°F/-1°C 4.c. Optimum storage temperature range: 40°F to 100°F/4°C to 38°C 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE The shelf life of unopened drums of ACCELL CLEAN® DWD is unlimited. Containers should always remain capped when not in use to prevent contamination and evaporation. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Aircrafts provide the most rapid method of applying dispersants to an oil spill and a variety of aircraft can be used for spraying. For aerial spraying, ACCELL CLEAN® DWD is applied undiluted. Typically application altitudes of 30 to 50 feet are recommended, although higher altitudes may be effective under certain conditions. Actual effective altitudes will depend on the application equipment, weather and aircraft. Careful selection of spray nozzles is critical to achieve desired dose levels, since droplet size must be controlled. A quarter- inch open pipe may be all that is necessary if the aircraft travels at 120 mph (104 knots) or more, since the air shear at these speeds will be sufficient to break the dispersant into the proper sized droplets. Agricultural spray delivery systems may not be suitable because of too fine of spray and too little delivery of ACCELL CLEAN® DWD to the affected area. Boat Spraying: ACCELL CLEAN® DWD may also be applied from boats equipped with spray booms mounted ahead of the bow wake or as far forward as possible. The most effective method of application from a boat is to apply ACCELL CLEAN® DWD using a low-volume, low- pressure pump so the ACCELL CLEAN® DWD can be applied undiluted. ACCELL CLEAN® DWD should not be fogged or atomized. Natural wave or boat wake action usually provides adequate mixing energy to disperse the oil. Application at sub-freezing temperatures may require larger nozzle, supply lines and orifices due to higher product viscosity. 2. Concentration/Application Rate: A treatment rate of about 10 gallons per acre, or a dispersant to oil ratio of 1:10 is optimal. The rate varies depending on the type of oil, degree of weathering, temperatures, and thickness of the slick. 3. Conditions for Use: For optimal results, ACCELL CLEAN® DWD early treatment of oil- contaminated waters is beneficial. ACCELL CLEAN® DWD can be used on weathered oils. Dispersants 163 ACCELL CLEAN® DWD ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested ACCELL CLEAN® DWD Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 5.66 96-hr 2.07 48-hr 11.10 96-hr 1.68 48-hr 8.05 96-hr 1.32 48-hr 6.60 96-hr 30.80 48-hr No. 2 Fuel Oil ACCELL CLEAN® DWD & No. 2 Fuel Oil (1:10) Reference Toxicant (DDS) b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (%) Prudhoe Bay Crude South Louisiana Crude Average of Prudhoe Bay and South Louisiana Crudes 58.70 96.03 77.37 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. FlashPoint: 130°F/55°C 2. Pour Point: -20.2°F/-29°C 3. Viscosity: 130 SUS @100°F 4. Specific Gravity: 1.0329 @60°F 5. pH: 5.8 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Miscible Dispersants 164 ACCELL CLEAN® DWD ------- X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium ND Copper ND Lead ND Mercury ND Nickel ND Zinc ND Cyanide ND Chlorinated Hydrocarbons ND Dispersants 165 ACCELL CLEAN® DWD ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 7/23/2021 7/27/2022 TECHNICAL PRODUCT BULLETIN #D-17 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 01, 2011 "FFT-SOLUTION®" I. NAME, BRAND, OR TRADEMARK FFT-SOLUTION® Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Fog Free Technologies, LLC 4365 Dorchester Road Building 300, Suite 301 North Charleston, SC 29405 Product Management: Office Phone: (843) 735-6626 Mobile: (478) 697-2588 E-mail: updated information required Website: www.fogfreetechnologies.com (Mr. William Knight) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Fog Free Technologies, LLC 4365 Dorchester Road Building 300, Suite 301 North Charleston, SC 29405 Product Management: Office Phone: (843) 735-6626 Mobile: (478) 697-2588 E-mail: updated information required Website: www.fogfreetechnologies.com (Mr. William Knight) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO: Non-Flammable, DOT: Non-Hazardous 2. Ventilation: Lowest level of skin protection is acceptable, but no special ventilation is required. 3. Skin and eye contact; protective clothing; treatment in case of contact: Lowest level of skin protection is acceptable. Avoid eye contact. In case of eye contact, immediately flush eyes with large amounts of water for at least 15 minutes. Avoid contact with skin. In case of skin contact, immediately flush with water and soap if available. For open systems where contact is likely, wear long sleeve shirt, chemical resistant gloves and chemical goggles. Dispersants 166 FFT-SOLUTION® ------- 4.a. Maximum storage temperature: 170°F 4.b. Minimum storage temperature: 30°F 4.c. Optimum storage temperature range: 40°F to 105°F 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE The shelf life of unopened drums of FFT-Solution® is limited to 60 months. Storage should be in a semi-controlled warehouse, out of direct sunlight. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Aerial Spraying - Aircraft provide the most rapid method of applying dispersants to an oil spill and a variety of aircraft can be used for spraying. For aerial spraying, FFT-Solution® is applied undiluted. Typical application altitudes of 30 to 50 feet have been used, although higher altitudes may be effective under certain conditions. Actual effective altitudes will depend upon application equipment, weather, and aircraft. Careful selection of spray nozzles is critical to achieve desired dose levels, since droplet size must be controlled. Many nozzles used for agricultural spraying are of low capacity and product fine a spray. A quarter-inch open pipe may be all that is necessary if the aircraft travels at 120 mph (104 knots) or more, since the air shear at these speeds will be sufficient to break the dispersant into the proper sized droplets. Optimal temperatures for application are between 33°F and 105°F. Boat Spraying - FFT-Solution® may also be applied by workboats equipped with spray booms mounted on the stern of the vessel. (Mounting boom on the stern prevents any over spray from making contact with boat operators.) The preferred and most effective method of application from a workboat is to use a low-volume, low-pressure pump so the chemical can be applied undiluted. Standard agriculture spray equipment is designed to make dosage adjustments or provide different spray tips that effect dosage rates. Natural wave or boat wake action usually provides adequate mixing energy to disperse the oil. A typical agriculture spray boom can be mounted to the stern to get wide coverage. The booms on shrimp boats also can be retrofitted to cover a much wider path during applications. The manufacturer also recommends that in lieu of spray tips on the booms, spray tips be changed into solid tubing for injection of FFT-Solution® 3 to 5 feet below the water surface. This will get the thicker crude slicks injected faster and with better results. FFT-Solution® should be applied as droplets, not fogged or atomized. 2. Concentration/Application Rate: A treatment rate of about 2 to 10 U.S. gallons per acre, or dispersant to oil ratio of 1:50 to 1:10 is recommended. This rate varies depending on the type of oil, degree of weathering, temperature, and thickness of the slick. 3. Conditions for Use: FFT-Solution® can be applied to weathered oil as well as light, medium, or heavy oils. Early treatment even at reduced treatment rates, can also counter the foaming tendencies of the spilled oil in turbulent waters. FFT-Solution® can be used on any type oil spills in salt water. Dispersants 167 FFT-SOLUTION® ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested FF T - S OLUTION® Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 5.34 96-hr 2.72 48-hr 40.80 96-hr 5.19 48-hr 5.14 96-hr 2.75 48-hr 2.42 96-hr 6.97 48-hr No. 2 Fuel Oil FF T - S OLUTION® & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (%) Prudhoe Bay Crude South Louisiana Crude Average of Prudhoe Bay and South Louisiana Crudes 49.97 48.87 49.42 VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 170°F 2. Pour Point: 23°F 3. Viscosity: 450 SUS @100°F 4. Specific Gravity: 1.0302 @60°F 5. pH: 9.96 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: None 9. Solubility: Product is 100% soluble in water Dispersants 168 FFT-SOLUTION® ------- X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium ND Copper ND Lead ND Mercury ND Nickel ND Zinc ND Cyanide ND Chlorinated Hydrocarbons ND Dispersants 169 FFT-SOLUTION® ------- TECHNICAL PRODUCT BULLETIN #D-18 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: APRIL 23, 2012 "MARINE D-BLUE CLEAN™" I. NAME, BRAND, OR TRADEMARK MARINE D-BLUE CLEAN™ Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT AGS Solutions, Inc. 5647 Nunn Street Houston, TX 77087 Phone: (713) 645-4933 Fax: (713)645-4903 E-mail: agssolutionsinc@gmail.com Website: www.agstx.com (Mrs. Linda Whiteley) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS AGS Solutions, Inc. 5647 Nunn Street Houston, TX 77087 Phone: (713) 645-4933 Fax: (713)645-4903 E-mail: agssolutionsinc@gmail.com Website: www.agstx.com (Mrs. Linda Whiteley) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: No special requirements. Drums and similar containers should be kept closed. Store in steel or plastic containers. 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of contact with eyes, wash thoroughly with plenty of clean water. Seek medical attention if irritation develops. Rubber protective gloves should be used if prolonged use of product is anticipated. Goggles, long sleeve shirt, and rubber gloves are recommended during application. 4.a. Maximum storage temperature: 170°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 40°F to 110°F 4.d. Temperatures of phase separations and chemical changes: Marine D-Blue Clean™ has a pour point of 30°F and may cause chemical changes at temperatures >110°F. Dispersants 170 MARINE D-BLUE CLEAN™ ------- V. SHELF LIFE Marine D-Blue Clean™ has a shelf life of >2 years, if unopened. Cleaner older than 24 months may still be viable. Ensure product is mixed well and then inspect to confirm the product is suitable for application. The product will not lose effectiveness unless the temperatures in >140°F. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Sprayer, boat, aircraft. Marine D-Blue Clean™ is to be used to disperse petroleum-based products in salt water. It may be applied by any conventional methods such as aerial spraying or surface vessel spraying, to accommodate weather conditions. Marine D-Blue Clean™ is to be applied undiluted, for aerial spraying. Timely application provides optimal results. Spray concentrated on the oil slick in atomized form such as with a manual pump or a pump system using moderately coarse droplets rather than a fine mist. 2. Concentration/Application Rate: Marine D-Blue Clean™ can be applied with a variety of spraying equipment, depending upon the type and scale of the water to be cleaned. For heavy concentrations of crude oil spill or temperatures below 40°F, Marine D-Blue Clean™ should be used without dilution in neat form. A dispersant to oil ratio up to 1 part dispersant to 20 parts of oil is suggested. Dose rates may vary depending on type and amount of petroleum spilled, and other site specific conditions such as weather, temperatures and extent of oil slick. 3. Conditions for Use: The performance of Marine D-Blue Clean™ is not affected by water salinity. Marine D-Blue Clean™ is useful on oil spills in salt water. It is effective with crude and residual heavy oil spills. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) MARINE D-BLUE CLEAN™ Menidia beryllina 18.00 96-hr Mysidopsis bahia 56.00 48-hr No. 2 Fuel Oil Menidia beryllina 18.00 96-hr Mysidopsis bahia 18.00 48-hr MARINE D-BLUE CLEAN™ & Menidia beryllina 32.00 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 18.00 48-hr Reference Toxicant (DSS) Menidia beryllina 1.06 96-hr Mysidopsis bahia 0.97 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OIL Oil Effectiveness (% Prudhoe Bay Crude 45.00 South Louisiana Crude 55.59 Average of Prudhoe Bay and South Louisiana Crudes 50.30 Dispersants 171 MARINE D-BLUE CLEAN™ ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: 30°F 3. Viscosity: 17.29 cSt @ 100°C 4. Specific Gravity: 1.035 @70°F 5. pH: 11.89 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: None 9. Solubility: Completely soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.25 Cadmium <0.005 Chromium <0.08 Copper <0.30 Lead <0.015 Mercury <0.0025 Nickel <0.350 Zinc <2.015 Cyanide <0.050 Chlorinated Hydrocarbons ND Dispersants 172 MARINE D-BLUE CLEAN™ ------- TECHNICAL PRODUCT BULLETIN #D-19 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 1, 2013 "COREXIT™ EC9500B" I. NAME, BRAND, OR TRADEMARK COREXIT™ EC9500B Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: DOT HazMat Classification - This product meets the criteria for classification as a Class 3 combustible liquid (49 CFR §173.120(b)(1)). However, it does not contain combustion, and, therefore, is not subject to the requirements for the Hazardous Materials Regulations (49 CFR §173.120(b)(3)). 2. Ventilation: Use with adequate ventilation equal to unobstructed outdoors in moderate breeze. 3. Skin and eye contact; protective clothing; treatment in case of contact: Do not get in eyes, on skin, or on clothing. In case of eye contact, rinse immediately with plenty of water and seek medical advice promptly. In case of skin contact, wash immediately with plenty of soap and water. If irritation persists or symptoms develop, seek medical attention. If clothing is contaminated, remove clothing and thoroughly wash the affected area. Do not take internally. In the event of oral ingestion, do not induce vomiting (can cause chemical pneumonia if aspirated into lungs). If conscious, wash out mouth and give water to drink. Get medical attention. If inhaled, remove to fresh air, treat symptomatically. Get medical attention. Dispersants 173 COREXIT™ EC9500B ------- For open systems where contact is likely, wear Tyvek, chemical resistant gloves (e.g., nitrile), and chemical splash goggles. Where concentrations in air may be high (e.g., confined area), the use of a half face filter mask or air supplied breathing apparatus is recommended. 4.a. Maximum storage temperature: 170°F 4.b. Minimum storage temperature: 40°F 4.c. Optimum storage temperature range: 40°F to 100°F 4.d. Temperatures of phase separations and chemical changes: No phase changes or chemical reactions are anticipated in the minimum to maximum storage range. Below 40°F, surfactant may slowly precipitate out of the solution, but it will return back into solution when warmed. V. SHELF LIFE The shelf life of unopened drums of COREXIT™ EC9500B is potentially unlimited when containers remain capped and sealed to prevent contamination and evaporation of solvents. Testing of COREXIT™ EC9500B is recommended every five years to ensure it remains fit for its intended purpose. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: For aerial spraying, apply COREXIT™ EC9500B undiluted. Various fixed-wing aircraft or helicopters can be used for spraying over a large area, from an altitude of 30 to 50 feet or even higher, depending on the application equipment and aircraft. Typical application altitudes of 30 to 50 feet have been used, although higher altitudes may be effective under certain conditions. Actual altitudes will depend on the application equipment, weather and aircraft. Careful selection of spray nozzles is critical to achieve desired dose levels, since droplet size must be controlled. Many nozzles used for agricultural spraying are of low capacity and produce too fine a spray. Avoid nozzles that produce a mist or fog. No nozzle may be necessary if the aircraft travels at 120 mph (104 knots) or more, since the air shear at these speeds will be sufficient to break the chemical stream into appropriately-sized droplets. For boat spraying (spray boom), COREXIT™ EC9500B may also be applied by workboats equipped with spray booms mounted ahead of the bow wake or as far forward as possible. The most effective method of application from a workboat could be the use of a low-volume, low- pressure pump. Spray equipment designed to provide a diluted dispersant solution to the spray booms can also be used. Dispersant concentrations in the 5 to 10 percent range are recommended; lower concentrations may result in significant fall-off in effectiveness. COREXIT™ EC9500B should be applied as droplets, not fogged or atomized. Natural wave or boat wake action usually provides adequate mixing energy to disperse the oil. Water from a fire hose can also be used for agitation of the treated slick. For boat spraying (fire monitor), a slightly modified fire monitor may be useful for applying dispersant concentrates such as COREXIT™ EC9500B from a boat. A screen cap is used on the nozzle of the monitor to obtain a uniform spray pattern with the proper sized droplet. Due to the volume output and the greater reach of the fire monitor, significantly more area can be covered in a shorter period of time than using conventional spray booms. Dispersants 174 COREXIT™ EC9500B ------- System Calibration - To facilitate successful application and dosage control, calibrate spray systems at the temperatures anticipated. Application at sub-freezing temperatures may require larger nozzle, supply lines and orifices due to higher product viscosity. 2. Concentration/Application Rate: A treatment rate of about 2 to 10 U.S. gallons per acre, or a dispersant to oil ratio of 1:50 to 1:10 is recommended; lower concentrations may also be used. This rate varies depending on the type of oil, degree of weathering, temperature, and thickness of the slick. 3. Conditions for Use: COREXIT™ EC9500B can be used on oil spills in salt waters and at any water temperature. The product can be used on most oils, weathered spills, and "chocolate mousse" (water-oil emulsions). Viscous oil may require higher dosage rates. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) COREXIT™ EC9500B Menidia beryllina 29.13 96-hr Mysidopsis bahia 10.00 48-hr No. 2 Fuel Oil Menidia beryllina 7.54 96-hr Mysidopsis bahia 2.51 48-hr COREXIT™ EC9500B & No. 2 Fuel Oil (1:10) Menidia beryllina 4.46 96-hr Mysidopsis bahia 2.13 48-hr Reference Toxicant (SLS) Menidia beryllina 12.19 96-hr Mysidopsis bahia 10.53 48-hr b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OILS Oil Effectiveness (%) Prudhoe Bay Crude 57.0 South Louisiana Crude 50.9 Average of Prudhoe Bay and South Louisiana Crudes 53.9 VIII. MICROBIOLOGICAL PROPERTIES NA IX. PHYSICAL PROPERTIES 1. Flash Point: 164°F 2. Pour Point: -44.0°F 3. Viscosity: 21.78 cSt at 40°C 4. Specific Gravity: 0.9626 at 15°C 5. pH: 6.29 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: CONFIDENTIAL 8. Solvents: CONFIDENTIAL Dispersants 175 COREXIT™ EC9500B ------- 9. Additives: None 10. Solubility: Miscible X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.0108 Cadmium <0.0020 Chromium <0.0060 Copper <0.0060 Lead <0.0040 Mercury <1.0000 (ug/L) Nickel <0.0100 Zinc <0.0060 Cyanide <0.0100 Chlorinated hydrocarbons 1.7600 Dispersants 176 COREXIT™ EC9500B ------- TECHNICAL PRODUCT BULLETIN #D-20 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 06, 2019 "CHIMEC CHIMSPERSE 6000" I. NAME, BRAND, OR TRADEMARK CHIMEC CHIMSPERSE 6000 Type of Product: Dispersant II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT CHIMEC S.p.A. Via deH'informatica 5 00071 Pomezia (RM), Italy Phone: +39-06-91825291 Fax: +39-06-91825225 E-mail: fnanchi@chimec.it (Mr. Francesco Nanchi, Deputy and Special Prosecutor for Manufacturing, Shipping, Safety, and Environment) CHIMEC Technical Manager and Primary Contact: Phone: +39-06-91825258 Fax: +39-06-91825262 E-mail: mmantarro@chimec.it (Mrs. Milena Mantarro) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS CHIMEC Technical Manager and Primary Contact: Phone: +39-06-91825258 Fax: +39-06-91825262 E-mail: mmantarro@chimec.it (Mrs. Milena Mantarro) CHIMEC S.p.A. Via deirinformatica 5 00071 Pomezia (RM), Italy Phone: +39-06-918251 Fax: +39-06-9194170 E-mail: mortolani@chimec.it (Mrs. Maria Angela Ortolani, Chairperson and Legal Representative) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-Flammable. 2. Ventilation: None under normal conditions. If exposure levels are exceeded or irritation is experienced, wear approved respiratory protection. In case of inadequate ventilation, oxygen deficient atmosphere, or where exposure levels are not known, wear approved respiratory protection (e.g., a mask fit for organic vapors (Al)). If inhaled, go into open air and ventilate suspected area. Obtain medical attention if breathing difficulty persists. 3. Skin and eye contact; protective clothing; treatment in case of contact: For skin protection, wear latex or neoprene gloves, and clothing with chemically resistant materials and fabric (e.g., trivalent suit). For eye and face protection, wear chemical safety glasses; or face shield with safety glasses. General first aid measures include never give anything by mouth to an unconscious person. If feeling unwell, see medical advice. After skin contact, remove Dispersants 177 CHIMEC CHIMSPERSE 6000 ------- contaminated clothing and drench affected area with water for at least 15 minutes. Obtain medical attention if irritation develops or persists. In case of eye contact, immediately rinse with water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get immediate medical advice/attention. If ingested, rinse mouth. DO NOT induce vomiting and obtain medical attention. 4.a. Maximum storage temperature: 104°F (40°C) continuous 4.b. Minimum storage temperature: -4°F (-20°C) 4.c. Optimum storage temperature range: 32°F (0°C) to 80°F (27°C) 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE The shelf life of opened containers is 12 months. If sealed as delivered, shelf life of closed containers is 24 months. Shelf life may be extended to 48 months after analytical checks. According to internal procedures for dispersant products, after 24 months the Chimec Quality Control department checks analytical parameters based on technical specifications before extending shelf life to 48 months. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: CHIMEC CHIMSPERSE 6000 may be applied by the usual methods (e.g., NIMBUS package, the Modular Aerial Spray System (MASS) package, or the Aerial Dispersant Delivery System (ADDS) package). The preferred and most effective method of application from a workboat is to use a low-volume, low-pressure pump. 2. Concentration/Application Rate: CHIMEC CHIMSPERSE 6000 is preferably used undiluted. A typical treatment rate is 10 to 15 L/acre or a DOR (dispersant to oil ratio) of 1:50 to 1:10. However, the treatment rate can vary depending on the type or oil, degree of weathering, temperature, and thickness of oil slick. For heavy oils, a 1:10 dilution ratio (product: water) is recommended. Lighter oils will require a 1:10 to 1:30 (product:water) dilution ratio. Warmer waters (greater than 78°F) and/or good agitation during application will require less product. 3. Conditions for Use: CHIMEC CHIMSPERSE 6000 can be used in salt water, with no limitations as to usage if within optimum temperature parameters (application may be made at or above 35°F, with optimum above 48°F). VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested CHIMSPERSE 6000 Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 2.51 96-hr 3.43 48-hr 4.48 96-hr 3.26 48-hr 3.01 96-hr 1.88 48-hr 1.86 96-hr 9.44 48-hr No. 2 Fuel Oil CHIMSPERSE 6000 & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Dispersants 178 CHIMEC CHIMSPERSE 6000 ------- b. Effectiveness: SWIRLING FLASK DISPERSANT EFFECTIVENESS TEST WITH SOUTH LOUISIANA (S/L) AND PRUDHOE BAY (P/B) CRUDE OILS Oil Effectiveness (% Prudhoe Bay Crude 48.30 South Louisiana Crude 58.50 Average of Prudhoe Bay and South Louisiana Crudes 53.40 VIII. MICROBIOLOGICAL PROPERTIES NA IX. PHYSICAL PROPERTIES 1. Flash Point: >100°F 2. Pour Point: -28°C 3. Viscosity: 26.8 cSt at 40°C 4. Specific Gravity: 0.9987 at 60°F 5. pH: 7.3 7. Surface Active Agents: CONFIDENTIAL 8. Solvents: CONFIDENTIAL 9. Additives: None 10. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 1.24 Cadmium <0.122 Chromium 0.254 Copper <0.272 Lead <0.118 Mercury <0.0132 Nickel 0.778 Zinc 5.24 Cyanide 1.75 Chlorinated hydrocarbons <1.80 Dispersants 179 CHIMEC CHIMSPERSE 6000 ------- MISCELLANEOUS OIL SPILL CONTROL AGENTS: TECHNICAL NOTEBOOK BULLETINS Miscellaneous Oil Spill Control Agents 180 Miscellaneous Oil Spill Control Agents ------- TECHNICAL PRODUCT BULLETIN #M-12 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 31, 1992 REVISED LISTING DATE: SEPTEMBER 13, 1995 "PES-51" I. NAME, BRAND, OR TRADEMARK PES-51 Type of Product: Miscellaneous Oil Spill Control Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Practical Environmental Solutions (Formerly known as Petroleum Environmental Services) P.O. Box 12563 San Antonio, Texas 78212 Phone: (210) 493-7172 Mobile Phone: (210) 875-4011 Fax: (210) 493-7172 E-mail: simsbi@aol.com Website: www.pes51.com (Mr. Bill Sims) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Practical Environmental Solutions (Formerly known as Petroleum Environmental Services) P.O. Box 12563 San Antonio, Texas 78212 Phone: (210) 493-7172 Mobile Phone: (210) 875-4011 Fax: (210) 493-7172 E-mail: simsbi@aol.com Website: www.pes51.com (Mr. Bill Sims) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: 124°F 2. Ventilation: Handle product in a normal well ventilated place. 3. Skin and eye contact; protective clothing; treatment in case of contact: Although PES-51 is expected not to pose any specific health hazard, the following precautions are recommended due to possible irritation from the biological by-produc2ts contained in the product: Avoid contact with skin, eyes, and clothing. Avoid prolonged or repeated contact with skin, breathing mist, and do not take internally. Keep product away from heat, sparks, and flames, and store in a cool, dry, well ventilated place, away from incompatible materials. Vent container in warm weather to relieve pressure. Do not cut, grind, weld, or drill on or near product containers. Handle empty containers just as would the full ones. Miscellaneous Oil Spill Control Agents 181 PES-51 ------- 4.a. Maximum storage temperature: NA. 4.b. Minimum storage temperature: NA 4.c. Optimum storage temperature range: NA 4.d. Temperatures of phase separations and chemical changes: Not applicable, butPES-51 freezes at -142°F. V. SHELF LIFE 6 years (unopened drum), 1 year (opened drum). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: The following PES-51 application methods are applicable for the full range of PES-51 industrial uses, including shoreline and surface treatment, tank cleaning and equipment decontamination. The selection of the method(s) will be dependent on the level and extent of hydrocarbon contamination, type of oil, and its degree of weathering/emulsion and the nature and type of surface to be treated or cleaned. Equipment availability, logistics and manpower requirements should also be considered. Application methods may be combined, if necessary. In addition, for shoreline cleaning, the treatment area will be boomed and contained prior to PES-51 usage. For equipment decontamination, the use of portable de-con pools or secondary containment liners are recommended. PORTABLE EQUIPMENT Hand Held Spraying - Spray PES-51 on the contaminated area using a Chapin Steel Sprayer #1729 (or equivalent), 2.5 gallons capacity, or the AU 8000 MicroNair sprayer. After application, allow 3 to 5 minutes for soaking without allowing evaporation of PES-51 (weather dependent). When saturation is attained, hydrocarbon will be seen running off the impacted surface. Rinse the treated surface with available water (fresh or sea water) from the pump until no hydrocarbon remains. The water should be used at ambient temperature. Depending on level and extent of contamination, a pressure washer may also be used for rinsing (ambient may be used). Collect the effluent hydrocarbons with absorbent booms and pads, and squeeze off the oil contaminants from the booms and pads for reuse as process oil. Airless Sprayer - Depending on the level and extent of the hydrocarbon contamination and the nature of the impacted surface, an airless type sprayer may be used for direct product application. Common types of airless sprayers are: Airlessco, Graeco or equivalents. These airless sprayers can have single or multi-hose attachments and can include wand extensions as required. Application rate and pressure will vary depending on the equipment type and site specific conditions. After spraying with PES-51, allow to soak for 3 to 5 minutes (weather dependent) avoiding evaporation, rinse/flush surfaces with pumps, fire hoses, deluge headers or pressure washers (ambient). Miscellaneous Oil Spill Control Agents 182 PES-51 ------- Pressure Washer with Syphon Feed System - Depending on the level and extent of the hydrocarbon contamination and the nature of the impacted surface proposed for treatment, a pressure washer may be used for direct product application. In most applications, hot water (greater than 120°F) is not necessary. Common types of pressure washers are: Hotsy and Lambda, or equivalents. These pressure washers have a variable rate "detergent syphon feed" system for PES-51 application and can have single or multi-hose attachments which can include wand extensions. Application rate and pressure will vary depending on equipment type and site specific conditions. After spraying with PES-51, allow to soak for 3 to 5 minutes (weather dependent) avoiding evaporation, rinse/flush surfaces with pumps, fire hoses, deluge headers or pressure washers (ambient). Air Knife (Modified for PES-51 Application) - PES has developed a patent-pending modified air knife system for product application. This method was developed primarily for rocky, cobble, bedrock type shorelines with both surface subsurface oil. The modified air knife delivers the PES-51 in both a liquid stream (125 psi) or as an aerosol. Compressed air is used to dilate subsurface sediments and allow for distribution of the PES-51. The air knife method is also applicable for surface treatment of impacted rocks, bulkheads, seawalls, rip-rap jetties, etc. After spraying with PES-51, allow to soak for 3 to 5 minutes (weather dependent) avoiding evaporation, rinse/flush surfaces with pumps, fire hoses, deluge headers or pressure washers (ambient). For subsurface treatment, continue flushing with large quantities of low-pressure seawater at ambient temperatures. MOBILE EQUIPMENT Boat Spraying - The recommended application rate is 1 to 5 gallons per 200 sq. ft., from a boat with speed of 1 to 3 knots, depending on the sea conditions and oil film thickness on the rocks. For a boat with a mounted AU-8110 MicroNair sprayer (or equivalent sprayer) and a spray swath of about 20 feet, traveling at approximately two knots, 25 acres/hr will be treated. After spraying, rinse PES-51 off the rocks with a hard, coarse spray of sea water. Standard size pumps with fire hoses or deluge headers may be used. Higher pressure rinses may be required if oil is thick and weathered. The shoreline may also be sprayed from the beach side, which will force the oil into the containment boom. Helicopter Deployed Spraying - Aerial spraying can be utilized for shore treatments and pretreatment with the AU 5000 atomizer (MicroNair) or equivalent sprayer. The recommended aerial application of PES-51 is 14 to 23 liters/minute. The AU 5000 (or equivalent) can be used with fixed-wing aircraft and helicopters operating at speeds of 90 MPH (145 km/hr) and more. The smaller AU 7000 sprayer (or equivalent) is recommended for use at airspeeds below 90 MPH. After spraying, the hydrocarbons can be rinsed off the shore rocks as described above with hand held pumps, deluge headers or boat spraying. Vehicular Spraying - The recommended vehicular spraying is 50 to 150 ft2/gallon depending on climatic conditions. A MicroNair vehicle-mounted sprayer is recommended. This unit is a self- Miscellaneous Oil Spill Control Agents 183 PES-51 ------- contained sprayer kit that combines the AU 8000 sprayhead (or equivalent) with a powerful 4- stroke engine and a 60 liter chemical tank to give complete product coverage. After spraying, the hydrocarbons can then be rinsed off the shore rocks as described above with hand held pumps, deluge headers or boat spraying. 2. Concentration/Application Rate: The product comes already mixed, and ready for use. For specific application, see rate of application as indicated above. 3. Conditions for Use: Water temperature and salinity do not affect the product performance. PES-51 is effective against hydrocarbons only, and the age of the hydrocarbon is not relevant. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) PES-51 Menidia beryllina 137.00 96-hr Mysidopsis bahia 54.00 48-hr No. 2 Fuel Oil Menidia beryllina 200.00 96-hr Mysidopsis bahia 11.50 48-hr PES-51 & Menidia beryllina 435.00 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 14.50 48-hr Reference Toxicant (DSS) Menidia beryllina 2.20 96-hr Mysidopsis bahia 9.80 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 124°F 2. Pour Point: -50°F at 30 min. 3. Viscosity: 30 cSt at 28°C 4. Specific Gravity: 0.840 at 25°C 5. pH: 6.7 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: CONFIDENTIAL 8. Solvents: CONFIDENTIAL 9. Additives: CONFIDENTIAL 10. Solubility: NA Miscellaneous Oil Spill Control Agents 184 PES-51 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) < 0.005 < 0.01 < 0.05 < 0.05 < 0.05 < 0.005 < 0.01 < 0.05 < 1.00 < 0.01 Miscellaneous Oil Spill Control Agents 185 PES-51 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #M-17 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: FEBRUARY 25, 1994 REVISED LISTING DATE: JUNE 14, 1995 "CIAGENT" I. NAME, BRAND, OR TRADEMARK CIAGENT Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier (formerly CI AGENT, CHEAP INSURANCE, & PETRO-CAPTURE) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT CIAGENT Solutions, LLC 11760 Commonwealth Dr. Louisville, KY 40299 Phone: updated information required Fax: updated information required E-mail: dan@ciagent.com (Mr. Dan Parker) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS CIAGENT Solutions, LLC 11760 Commonwealth Dr. Louisville, KY 40299 Phone: updated information required Fax: updated information required E-mail: dan@ciagent.com (Mr. Dan Parker) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Flammable solid at >210°F. 2. Ventilation: Normal ventilation is adequate. 3. Skin and eye contact; protective clothing; treatment in case of contact: Product may cause slight eye irritation if in contact with eyes. Use protective eye goggles when handling the product. In case of eye contact, flush eyes with water. In an enclosed environment, workers should wear a dust mask for personal comfort. In case of a confined space fire, do not enter without full bunker gear and positive pressure NIOSH approved self-contained breathing apparatus. Maintain fire watch at 450°F. 4.a. Maximum storage temperature: 190°F 4.b. Minimum storage temperature: None 4.c. Optimum storage temperature range: 50°F - 80°F 3/17/2016 7/27/2022 Miscellaneous Oil Spill Control Agents 186 CIAGENT ------- 4.d. Temperatures of phase separations and chemical changes: None. Avoid contact with strong oxidizing agents due to possible oxidation reaction with the product. V. SHELF LIFE > 5 years, if stored in cool dry area, away from direct sunlight. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: For small scale spills on water (salt or fresh), CIAGENT can be broadcast directly onto the spill, spreading a thin layer from the outer edge into the middle of the spill. Agitation is not necessary. The product is also available in oil absorbent, water repellant booms and pillows. For large spills on water (fresh or salt), CIAGENT may be deployed with an air or water stream directed at the leading edge of the spill. Because of its fine particulate nature, static buildup may occur if the product is applied in dry form at a high rate of delivery. Dispensing material should be properly grounded to prevent this. The product is relatively non- abrasive and should not harm machinery or pumping systems. Agitation is not necessary. The polymer has a specific gravity of less than one and will tend to separate and move to the surface when mixed with water. Therefore, in the case of water carrying media, the product should be introduced "just in time" as the media is sprayed, or agitation will be needed to keep the product suspended. The product will remove oils and other hazardous hydrocarbon based materials from fresh or salt water. CIAGENT may be used in a flow-through filter to remediate contaminated water. CIAGENT encapsulates and solidifies the oil, while continuing to float even after saturation. The solidified oil or hazardous material may be removed from water using a vacuum pump or fish net. The material should be put into appropriate containers and disposed of in accordance with federal, state and local regulations. For spills on land, the product would be applied in the same manner as in the water-based spill situation. Agitation is not necessary. To recover solidified oil or hazardous materials from spills on land, the spent material may be collected and swept up using an industrial vacuum cleaner, broom, or shovel. The material should be put into appropriate containers and disposed of in accordance with federal, state and local regulations. 2. Concentration/Application Rate: In general, a 10% to 30% by weight application is required to solidify light, medium, and heavy oils. Solidification may occur faster if additional CIAGENT is applied. 3. Conditions for Use: CIAGENT is equally effective in fresh or salt water, and under any weather conditions; however, colder temperatures may slow the solidification process. The product is most effective on water temperatures between 32°F and 120°F. Depending on the age and/or viscosity of the material, varying amounts of CIAGENT may be required to obtain complete solidification. The recovered solidified oil or hazardous materials may be landfilled, incinerated, used as a secondary fuel, or otherwise disposed of according to federal, state and local regulations. Miscellaneous Oil Spill Control Agents 187 CIAGENT ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) CIAGENT Menidia beryllina 2227.00 96-hr Mysidopsis bahia 2617.00 48-hr No. 2 Fuel Oil Menidia beryllina 4.36 96-hr Mysidopsis bahia 1.45 48-hr CIAGENT & Menidia beryllina 5.93 96-hr No. 2 Fuel (1:10) Mysidopsis bahia 1.73 48-hr Reference Toxicant (DSS) Menidia beryllina 3.68 96-hr Mysidopsis bahia 6.82 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA IX. PHYSICAL PROPERTIES AND COMPONENTS 1. Flash Point: No flash observed at 210DF. 2. Pour Point: Not applicable; solid samples 3. Viscosity: Not applicable; solid samples 4. Specific Gravity: 0.94 g/cm3 5. pH: 7.81 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: None 8. Solvents: None 9. Additives: None 10. Solubility: Negligible X. ANALYSIS FOR HEAVY METALS AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <1.0 Cadmium <2.5 Chromium <2.0 Copper <2.5 Lead <5.0 Mercury <0.050 Nickel <5.0 Zinc <2.5 Cyanide <0.50 Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 188 CIAGENT ------- TECHNICAL PRODUCT BULLETIN #M-18 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 29, 1994 REVISED LISTING DATE: MARCH 12, 1997 "ZYME-FLOW" (aka, ZYME-TREAT, MARI-ZYME, UNITED 658 PETRO-ZYME) I. NAME, BRAND, OR TRADEMARK ZYME-FLOW (aka, ZYME-TREAT, MARI-ZYME, UNITED 658 PETRO-ZYME)Type of Product: Miscellaneous Oil Spill Control Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT United Laboratories, Inc. 320 37th Avenue St. Charles, IL 60174 Phone: (630) 377-0900 x7408 or (800) 323-2594 Fax: (630) 377-0960 E-mail: nsherrel@unitedlabsine.com (Ms. Nancy Sherrel) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS United Laboratories, Inc. 320 37th Avenue St. Charles, IL 60174 Phone: (630) 377-0900 x7408 or (800) 323-2594 Fax: (630) 377-0960 E-mail: nsherrel @unitedl ab sine. com (Ms. Nancy Sherrel) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: No mechanical ventilation required 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye contact due to possible mild eye irritation. In case of eye contact, flush eyes with water. Protective clothing is normally not required. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 0°F 4.c. Optimum storage temperature range: 0°F - 120°F 4.d. Temperatures of phase separations and chemical changes: > 3 freeze-thaw cycles. V. SHELF LIFE 1 year minimum. Miscellaneous Oil Spill Control Agents 189 ZYME-FLOW ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: United's ZYME-FLOW is a chemically designed product that will make heavy crudes more pumpable, and break the adhesion between oils and soil, rock or sand. ZYME-FLOW can be applied where the contaminated soil or sand is temporarily removed and placed into a device that can provide mechanical agitation (e.g., a cement mixer or a fractionating tank). Unagitated tanks may also be used, but more time will be required to achieve the goal. Add ZYME-FLOW solution to the tank. As agitation continues, oils with a specific gravity of less than one will float, while oils with a specific gravity of greater than one will settle. The floating or settled oil can then be removed from the soil or sand. As ZYME-FLOW will not emulsify oils, the recovered oils are almost anhydrous, and the water can be collected and reused. Another method is to physically isolate a small area that is to be cleaned with damming collars, sand bags or other means on the sides and a none permeable layer on the bottom (if possible). Then wash the contaminated area with ZYME-FLOW solution using a pressurized water stream. Keep the area super-saturated with water for several hours to allow oil residues to float to the surface for collection. ZYME-FLOW can be used to wash the inside or outside of a ship or barge that has been contaminated with oil, using a high pressure sprayer. Bilges of a ship, or barge can also be cleaned using a 1% ZYME-FLOW solution, and allowing the natural movement of the ship to provide the agitation. 2. Concentration/Application Rate: The exact dilution of ZYME-FLOW will vary between 50:1 and 200:1 depending on temperature, viscosity and type of petroleum product. 3. Conditions for Use: ZYME-FLOW is effective in all non-frozen waters with greater efficacy as the temperature increases. The product efficiency is not affected by salinity, but it will be affected by tar sand. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) ZYME-FLOW Menidia beryllina 35.00 96-hr Mysidopsis bahia 26.00 48-hr No. 2 Fuel Oil Menidia beryllina 6.90 96-hr Mysidopsis bahia 3.70 48-hr ZYME-FLOW & Menidia beryllina 8.70 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 1.60 48-hr Reference Toxicant (SDS) Menidia beryllina 7.07 96-hr Mysidopsis Bahia 18.60 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA Miscellaneous Oil Spill Control Agents 190 ZYME-FLOW ------- IX. PHYSICAL PROPERTIES 1. Flash Point: None 2. Pour Point: 32°F 3. Viscosity: <10 cps 4. Specific Gravity: 0.99 5. pH: 7.0 - 8.0 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: CONFIDENTIAL 8. Solvents: NA 9. Additives: CONFIDENTIAL 10. Solubility: Soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.005 Cadmium 0.002 Chromium 0.002 Copper 0.020 Lead 0.007 Mercury 0.0004 Nickel 0.070 Zinc 0.040 Cyanide 0.300 Chlorinated Hydrocarbons <1.00 Miscellaneous Oil Spill Control Agents 191 ZYME-FLOW ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 11/03/2008 7/27/2022 TECHNICAL PRODUCT BULLETIN #M-19 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: APRIL 22, 1996 "WASTE-SET #3200®" I. NAME, BRAND, OR TRADEMARK WASTE-SET #3200® Type of Product: Miscellaneous Oil Spill Control Agent - Oil Spill Solidifying Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Environmental & Fire Technology, LLC Address: updated information required Phone: updated information required (Mr. Cal Blystra) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Environmental & Fire Technology, LLC Address: updated information required Phone: updated information required (Mr. Cal Blystra) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Product will not burn unless preheated. Avoid elevated temperatures (>200°F) for extended periods (>5 days). Product has a tendency to accumulate a static charge during transport, which is a potential fire hazard if used near flammables. 2. Ventilation: Avoid generating dust clouds. 3. Skin and eye contact; protective clothing; treatment in case of contact: May cause mild mechanical irritation to eyes, skin and respiratory tract. Dust may cause coughing and watery eyes. Pre-existing eye, skin and respiratory disorders may be aggravated by this product. Wear NIOSH-approved respirator to prevent overexposure. Refer to transitional occupational exposure limits established by OSHA in 29CFR 1910.1000. Flush eyes with water; wash skin with soap and water; if molten, treat as for burns. Remove person(s) to fresh air if excessive amounts of dust have been inhaled. Protective gloves and safety glasses should be worn. If material is released or spilled, sweep up or vacuum and place in an approved container. 4.a. Maximum storage temperature: 200°F 4.b. Minimum storage temperature: None 4.c. Optimum storage temperature range: <200°F 4.d. Temperatures of phase separations and chemical changes: >450°F Miscellaneous Oil Spill Control Agents 192 WASTE-SET #3200 ------- V. SHELF LIFE Unlimited. VI. RECOMMENDED APPLICATION PROCEDURE 1 .Application Method: Spills on Water - For spills on water, surround the spill with WASTE-SET® 3200 to prevent migration. Reinforce containment line with a boom or sweep if necessary. WASTE-SET® and the resulting reacted material will float. If the interior of the diked spill is not to be reclaimed, fill in the remaining surface area of the spill by broadcasting additional WASTE-SET® 3200 evenly over the spill until the WASTE- SET® no longer reacts with the spill. Alternatively, the product may be introduced under the surface of the spill to rise and react with oils in the suspension layer. WASTE-SET® can then be swept or netted from the surface of the water. Spills on Hard Surfaces - For spills on hard surfaces, apply WASTE-SET 3200® heavily to perimeter of spill to prevent migration. After surrounding the spill, reinforcement of the containment line thus formed with a boom or sweep may be advisable depending on the volume and flow rate. If the interior of the diked spill is not to be reclaimed, fill in the remaining surface of the spilled material by evenly distributing additional WASTE-SET 3200® until the WASTE-SET® no longer reacts with the spill and remains white and on the surface. Disposal - Dispose of reacted material in accordance with local, state, and federal regulation. Under the EPA Toxicity Characteristic Leaching Procedures (TCLP), WASTE-SET encapsulated material may be eligible for disposal in landfills. Incineration results in extremely low ash content. Dependent upon the nature of the encapsulated material, it may also be disposed of by incorporation into synthetic surfaces such as asphalt. WASTE-SET® will effectively "encapsulate" crude oil and petroleum-based products, such as gasoline, kerosene, and diesel fuel; in addition to the various following liquid and vapor-phase contaminants: Aliphatic hydrocarbons Esters Aromatic hydrocarbons Ethers Chlorinated hydrocarbons Ketones Alcohols Other hydrocarbons 2. Concentration/Application Rate: One pound WASTE-SET® per five pounds of oil (May vary with viscosity and temperature). 3. Conditions for Use: No limitations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) WASTE-SET 3200® Menidia beryllina >10000.0 96-hr Miscellaneous Oil Spill Control Agents 193 WASTE-SET #3200 ------- Mysidopsis bahia 5431.0 48-hr No. 2 Fuel Oil Menidia beryllina 274.0 96-hr Mysidopsis bahia 29.0 48-hr WASTE-SET 3200® & Menidia beryllina 552.0 96-hr No. 2 Fuel Oil Mysidopsis bahia 58.0 48-hr Reference Toxicant (SDS) Menidia beryllina 1.8 96-hr Mysidopsis bahia 4.9 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: No flash observed at 310°F 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: 0.94 5. pH: NA 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: NA 8. Solvents: None 9. Additives: None 10. Solubility: Insoluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium 0.44 Copper 0.98 Lead 0.08 Mercury ND Nickel 0.38 Zinc 3.1 Cyanide ND Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 194 WASTE-SET #3200 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 11/03/2008 7/27/2022 TECHNICAL PRODUCT BULLETIN #M-20 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: APRIL 22, 1996 "WASTE-SET #3400®" I. NAME, BRAND, OR TRADEMARK WASTE-SET #3400® Type of Product: Miscellaneous Oil Spill Control Agent - Oil Spill Solidifying Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Environmental & Fire Technology, LLC Address: updated information required Phone: updated information required (Mr. Cal Blystra) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Environmental & Fire Technology, LLC Address: updated information required Phone: updated information required (Mr. Cal Blystra) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Product will not burn unless preheated. Avoid elevated temperatures (>200°F) for extended periods (>5 days). Product has a tendency to accumulate a static charge during transport, which is a potential fire hazard if used near flammables. 2. Ventilation: Avoid generating dust clouds. 3. Skin and eye contact; protective clothing; treatment in case of contact: May cause mild mechanical irritation to eyes, skin and respiratory tract. Dust may cause coughing and watery eyes. Pre-existing eye, skin and respiratory disorders may be aggravated by this product. Wear NIOSH-approved respirator to prevent overexposure. Refer to transitional occupational exposure limits established by OSHA in 29CFR 1910.1000. Flush eyes with water; wash skin with soap and water; if molten, treat as for burns. Remove person(s) to fresh air if excessive amounts of dust have been inhaled. Protective gloves and safety glasses should be worn. If material is released or spilled, sweep up or vacuum and place in an approved container. 4.a. Maximum storage temperature: 200°F 4.b. Minimum storage temperature: None 4.c. Optimum storage temperature range: <200°F 4.d. Temperatures of phase separations and chemical changes: >450°F Miscellaneous Oil Spill Control Agents 195 WASTE-SET #3400 ------- V. SHELF LIFE Unlimited. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spills on Water - For spills on water, surround the spill with WASTE-SET® 3400 to prevent migration. Reinforce containment line with a boom or sweep if necessary. WASTE-SET® and the resulting reacted material will float. If the interior of the diked spill is not to be reclaimed, fill in the remaining surface area of the spill by broadcasting additional WASTE-SET 3400® evenly over the spill until the WASTE-SET® no longer reacts with the spill. Alternatively, the product may be introduced under the surface of the spill to rise and react with oils in the suspension layer. WASTE-SET® can then be swept or netted from the surface of the water. Spills on Hard Surfaces - For spills on hard surfaces, apply WASTE-SET® 3400 heavily to perimeter of spill to prevent migration. After surrounding the spill, reinforcement of the containment line thus formed with a boom or sweep may be advisable depending on the volume and flow rate. If the interior of the diked spill is not to be reclaimed, fill in the remaining surface of the spilled material by evenly distributing additional WASTE-SET® 3400 until the WASTE- SET® no longer reacts with the spill and remains white and on the surface. Disposal - Dispose of reacted material in accordance with local, state, and federal regulation. Under the EPA Toxicity Characteristic Leaching Procedures (TCLP), WASTE-SET® encapsulated material may be eligible for disposal in landfills. Incineration results in extremely low ash content. Dependent upon the nature of the encapsulated material, it may also be disposed of by incorporation into synthetic surfaces such as asphalt. WASTE-SET® will effectively "encapsulate" crude oil and petroleum-based products, such as gasoline, kerosene, and diesel fuel; in addition to the various following liquid and vapor-phase contaminants: Aliphatic hydrocarbons Esters Aromatic hydrocarbons Ethers Chlorinated hydrocarbons Ketones Alcohols Other hydrocarbons 2. Concentration/Application Rate: One pound WASTE-SET® per five pounds of oil (May vary with viscosity and temperature). 3. Conditions for Use: No limitations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) WASTE-SET 3400® Menidia beryllina >10000.0 96-hr Mysidopsis bahia >10000.0 48-hr No. 2 Fuel Oil Menidia beryllina 274.0 96-hr Mysidopsis bahia 29.0 48-hr Miscellaneous Oil Spill Control Agents 196 WASTE-SET #3400 ------- WASTE-SET 3400® & Menidia beryllina 442.0 96-hr No. 2 Fuel Oil Mysidopsis bahia 36.0 48-hr Reference Toxicant (SDS) Menidia beryllina 1.8 96-hr Mysidopsis bahia 4.9 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: No flash observed at 350°F 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: 0.91 5. pH: NA 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: NA 8. Solvents: None 9. Additives: None 10. Solubility: Insoluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium 0.41 Copper 0.97 Lead 0.08 Mercury ND Nickel 3.3 Zinc 4.0 Cyanide ND Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 197 WASTE-SET #3400 ------- TECHNICAL PRODUCT BULLETIN #M-22 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: FEBRUARY 27, 1998 REVISED LISTING DATE: OCTOBER 5, 1998 "PX-700®" I. NAME, BRAND, OR TRADEMARK PX-700® Type of Product: Miscellaneous Oil Spill Control Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Enviro-Tech 715 NE 19th Place #22 Cape Coral, FL 33909 Phone: (239) 673-8280 Fax: (239) 424-8408 E-mail: info@px700.com Website: www.px700.com (Mr. Charlie Jones) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Enviro-Tech 715 NE 19th Place #22 Cape Coral, FL 33909 Phone: (239) 673-8280 Fax: (239) 424-8408 E-mail: info@px700.com Website: www.px700.com (Mr. Charlie Jones) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Not flammable; no special precautions necessary. 2. Ventilation: None required; no vapor emissions at normal temperatures, summer and winter. 3. Skin and eye contact; protective clothing; treatment in case of contact: Product contains a surfactant; avoid prolonged skin contact. Mild eye irritant; in case of eye contact, flush with copious amounts of water. No protective clothing required. Contact treatment is to flush with water. Product is acidic (pH 3.5-4.0). Eye protection is recommended as a precaution against splashing. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 30°F 4.c. Optimum storage temperature range: 65°F - 85°F 4.d. Temperatures of phase separations and chemical changes: Separation may occur after 3 months. Separation will not affect product performance. Miscellaneous Oil Spill Control Agents 198 PX-700™ ------- V. SHELF LIFE Two years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: To remove oily sheen from areas surrounding an oil spill, spray undiluted PX-700® directly over area at an application rate of one gallon for every 900 to 1200 square feet of surface area. Dilute PX-700® 25:1 for cleaning equipment and other surfaces. Either spray or immerse equipment, as applicable. Dilute PX-700® 50:1 for immersing wildlife to remove oil. 2. Concentration/Application Rate: At normal temperatures product is free flowing and applied full strength to remove oily sheen from aquatic environments, soils, and wastewater. 3. Conditions for Use: Water salinity, water temperature, types and ages of pollutants. Do not allow product to freeze, as separation may occur. Product may work more slowly at low temperatures. At full strength or diluted with fresh water, product will have a specific gravity lower than sea water and should float. Use of PX-700® should aid skimming and other conventional oil recovery operations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (DDm) PX-700® Menidia beryllina 380.00 96-hr Mysidopsis bahia 297.00 48-hr No. 2 Fuel Oil Menidia beryllina 7.07 96-hr Mysidopsis bahia 1.89 48-hr PX-700® Menidia beryllina 5.65 96-hr & No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.77 48-hr Reference Toxicant (DDS) Menidia beryllina 6.16 96-hr Mysidopsis bahia 23.00 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: Not flammable 2. Pour Point: 30°F 3. Viscosity: Equivalent to water 4. Specific Gravity: 1.0 5. pH: 3.5 to 4.0 standard units 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL Miscellaneous Oil Spill Control Agents 199 PX-700™ ------- 7. Surface Active Agents: Less than 5% Cocamide 8. Solvents: None 9. Additives: Citric acid for pH control 10. Solubility: 100% soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.47 Cadmium ND Chromium ND Copper 0.14 Lead ND Mercury ND Nickel ND Zinc 0.77 Cyanide ND Chlorinated Hydrocarbons CONFIDENTIAL Miscellaneous Oil Spill Control Agents 200 PX-700™ ------- TECHNICAL PRODUCT BULLETIN #M-23 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 23, 1998 "ALSOCUP" I. NAME, BRAND, OR TRADEMARK ALSOCUP Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT REVCOM Associates 1550 Rimpau Avenue #53 Corona, CA 92881 Phone: (951)737-0104 E-mail: revcom@sbcglobal.net (Mr. Dave Naylor, President) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS REVCOM Associates 1550 Rimpau Avenue #53 Corona, CA 92881 Phone: (951)737-0104 E-mail: revcom@sbcglobal.net (Mr. Dave Naylor, President) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: NA 2. Ventilation: NA 3. Skin and eye contact; protective clothing; treatment in case of contact: ALSOCUP is practically non-irritating to the eyes and is non-irritating to the skin. Safety glasses and protective clothing should be worn when applying the material. The product is not expected to cause irritation to the nose, throat, or respiratory tract. 4.a. Maximum storage temperature: 163°F 4.b. Minimum storage temperature: 0°F 4.c. Optimum storage temperature range: 0°F to 163°F 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE ALSOCUP has a shelf life of five years. Miscellaneous Oil Spill Control Agents 201 ALSOCUP ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: ALSOCUP is used to collect petroleum-based products spilled on water or land. When ALSOCUP comes into contact with a petroleum product it chemically bonds and traps the petroleum. Once captured, spilled product cannot be released from ALSOCUP. ALSOCUP does not absorb water and will not sink. The product can be collected by skimming with pumps or mechanical devices. 2. Concentration/Application Rate: ALSOCUP is used by applying one pound of product to each 10 pounds of spilled petroleum products. 3. Conditions for Use: Water temperature does not appear to affect the ability of ALSOCUP to collect petroleum products. Heavy seas may prevent containment of an oil spill, and the product would lose efficiency if the oil product dispersed. Booms and dams that contain the petroleum product into an area are most effective when using ALSOCUP. In water the motion of the sea will mix the product with oil. On land a mechanical means is necessary to combine the oil with ALSOCUP. ALSOCUP will collect petroleum products at any stage; however, it is most effective early in the spill before dispersion. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: ALSOCUP is a non-toxic substance. The product is generally considered to have a low order of acute oral toxicity. Material Tested Species LC50 (DDm) ALSOCUP Menidia beryllina >100 96-hr Mysidopsis bahia >100 48-hr No. 2 Fuel Oil Menidia beryllina 8.1 96-hr Mysidopsis bahia 3.9 48-hr ALSOCUP & No. 2 Fuel Oil (1:10) Menidia beryllina 14.0 96-hr Mysidopsis bahia 10.0 48-hr Reference Toxicant (DSS) Menidia beryllina NA Mysidopsis bahia NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: NA 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: NA 5. pH: NA 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: NA 9. Solubility in Water: NA Miscellaneous Oil Spill Control Agents 202 ALSOCUP ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.0211 0.090 0.456 0.445 0.454 0.00492 0.474 0.433 ND NA Miscellaneous Oil Spill Control Agents 203 ALSOCUP ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 5/18/2006 7/27/2022 TECHNICAL PRODUCT BULLETIN #M-24 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JANUARY 26, 2001 "RAPIDGRAB 2000™" I. NAME, BRAND, OR TRADEMARK RAPIDGRAB 2000™ Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT GlobeMark Resources Ltd. 1312 Mill Creek Drive Sal ado, TX 76517 Mobile: (254) 231-2251 E-mail: fiddler656@gmail.com Website: www.globemarkresources.com (Ms. Joannie Docter) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS GlobeMark Resources Ltd. 1312 Mill Creek Drive Sal ado, TX 76517 Mobile: (254) 231-2251 E-mail: fiddler656@gmail.com Website: www.globemarkresources.com (Ms. Joannie Docter) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO - Non-flammable; DOT - Non-hazardous 2. Ventilation: Use with ventilation equal to unobstructed outdoors in a moderate breeze. 3. Skin and eye contact; protective covering; treatment in case of contact: Avoid skin and clothing contact. If skin contact occurs, immediately wash with large amounts of water and soap (if possible). Remove any contaminated clothing or shoes. Launder before reusing. If irritation persists, seek medical assistance. For areas where contact is likely, wear long sleeve shirt, chemical resistant gloves, and chemical resistant goggles. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 0°F 4.c. Optimum storage temperature range: 32°F to 90°F 4.d. Temperatures of phase separations and chemical changes: None Miscellaneous Oil Spill Control Agents 204 RAPIDGRAB 2000™ ------- V. SHELF LIFE The shelf life of unopened drums of RAPIDGRAB 2000™ is unlimited. Containers should be capped when not being used to prevent contamination and evaporation. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: RAPIDGRAB 2000™ is a non-ionic liquid formulation that may be effectively applied by mist spraying onto floating oil slicks and sheens that are often found in harbors and at sea as the result of oil leakage and spills from ships. It instantly reduces and confines floating oils by the oleophitic synergistic effect of contraction and congealment into a physical state that greatly simplifies cleanup operations. Oil slicks and sheens may be reduced by up to 1,000 percent or more. The broad temperature range for RAPIDGRAB 2000™ sprays are from 32°F to 120°F. Aerial Spraying - Typical application altitudes of 30 to 50 feet are advised although higher altitudes may be used if condition warrant. Spray nozzle should be about Vi inches in diameter at 104 knots or more to create enough air shear sufficient to break the RAPIDGRAB 2000™ into proper sized droplets. A '/2-inch diameter nozzle may be needed for temperatures below 50°F. Boat Spraying - Mist sprays may be applied from shipboard by power "foggers." 2. Concentration/Application Rate: RAPIDGRAB 2000™ should be mist sprayed full strength on surface oil until sufficient herding results are achieved. Results will vary depending on oil type, temperature, wave action, and viscosity. 3. Conditions for Use: RAPIDGRAB 2000™ is designed to be used after oil has been contained by booms or other similar apparatus. Timely treatment with RAPIDGRAB 2000™, even at low application rates, can help to contain the sheen/spreading effect of the oil slick. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested RAPIDGRAB 2000™ Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 5.13 96-hr 2.29 48-hr 9.34 96-hr 3.12 48-hr 4.07 96-hr 2.60 48-hr 2.97 96-hr 6.71 48-hr No. 2 Fuel Oil RAPIDGRAB 2000™ & No. 2 Fuel Oil (1:10) Reference Toxicant (SRTT) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Miscellaneous Oil Spill Control Agents 205 RAPIDGRAB 2000™ ------- IX. PHYSICAL PROPERTIES 1. FlashPoint: 110°C 2. Pour Point: 30°F 3. Viscosity: 20.2 4. Specific Gravity: 0.84 5. pH: 6.95 6. Surface Active Agents: Oleophitic surfactant 7. Solvents: Proprietary formulation oleophitic surfactants 8. Additives: None 9. Solubility in Water: Miscible in oil and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium ND Copper ND Lead ND Mercury <0.1 Nickel ND Zinc ND Cyanide 2.8 Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 206 RAPIDGRAB 2000™ ------- LISTING CHANGES PENDING; VERIFICATION BY MANUFACTURER AND EPA REQUIRED TECHNICAL PRODUCT BULLETIN #M-25 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 9, 2006 "OIL SOLUTIONS POWDER" (aka, AQUA N-CAP™ POLYMER) I. NAME, BRAND, OR TRADEMARK OIL SOLUTIONS POWDER (aka, AQUA N-CAP™ POLYMER) Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Oil Solutions International 35 Mill Street Amityville, NY 11701 Phone: (631)608-8889 Fax: (631)789-1676 E-mail: 4oilgreen@gmail.com Website: www.cleaningupoil.com (Mr. Dennis J. Traina, President) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Oil Solutions International 35 Mill Street Amityville, NY 11701 Phone: (631)608-8889 Fax: (631)789-1676 E-mail: 4oilgreen@gmail.com Website: www.cleaningupoil.com (Mr. Dennis J. Traina, President) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Work in a well-ventilated area. Avoid excessive inhalation of dust. 3. Skin and eye contact; protective covering; treatment in case of contact: Skin contact - No recommendation is made specifying the need for personal protective clothing to prevent skin contact. Person(s) should wash daily at the end of each work shift. Exposed areas should be thoroughly washed with water. Eye contact - Product may cause irritation as any normal dust. Wear appropriate eye protection, compliant with ANSI Standard Z87.1, to prevent eye contact. If eye irritation or redness is experienced, promptly wash eyes with large amounts of water, for at least 15 minutes, occasionally lifting the lower and upper lids. Should eye irritation persist, seek Miscellaneous Oil Spill Control Agents 207 OIL SOLUTIONS POWDER ------- medical attention immediately. Contact lenses should not be worn when working with this product. Inhalation - Wear appropriate respiratory protection, compliant with OSHA standard 29 CFR 1910.134, to prevent inhalation. If a respiratory disorder is observed, remove person(s) from the work area immediately. Should respiratory disorder persist, seek medical attention immediately. Ingestion - Rinse mouth with water and seek medical attention immediately. 4.a. Maximum storage temperature: 185°F 4.b. Minimum storage temperature: NA 4.c. Optimum storage temperature range: 185°F 4.d. Temperatures of phase separations and chemical changes: None. Polymer may accumulate static charge during transport, handling, and processing. Static charge can be a potential fire hazard in the presence of volatile or flammable materials or in high airborne dust conditions. V. SHELF LIFE Not limited. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Apply OIL SOLUTIONS POWDER along the outer edges of spill area to prevent spill migration. Proceed by applying product onto remaining spill area, until a light white excess of product is observed. OIL SOLUTIONS POWDER may be broadcast onto the spill by hand or with a mechanical blower. Lighter hydrocarbons and synthetic oils will clump into a soft cluster like material easily recoverable with a net or other means as appropriate. 2. Concentration/Application Rate: Apply OIL SOLUTIONS POWDER at a rate of 0.5 to 2 lbs per gallon of spilled hydrocarbon. Depending on the type of hydrocarbon and recovery operations employed, more or less product may be used to achieve recoverable solid mat/residue. Allow approximately 30-60 minutes of contact time, product will form an elastic or rubber-like mat material. Mat like material may be removed whole or segmented as appropriate. 3. Conditions for Use: OIL SOLUTIONS POWDER differs from traditional sorbents in that it initially behaves like a synthetic sorbent, then as a solidifier as the molecular microencapsulating process occurs. Once encapsulated, the spilled oil is captured within the polymer matrix. OIL SOLUTIONS POWDER is designed to cleanup a wide variety of crude oil, refined hydrocarbon products (i.e., fuels, oils, hydraulic fluids), and synthetic fluids spilled on water and surfaces. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) OIL SOLUTIONS POWDER Menidia beryllina 484,000 96-hr Mysidopsis bahia 104,000 48-hr No. 2 Fuel Oil Menidia beryllina 15.80 96-hr Mysidopsis bahia 1.45 48-hr OIL SOLUTIONS POWDER & Menidia beryllina 22.50 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.13 48-hr Reference Toxicant (SRTT) Menidia beryllina 3.65 96-hr Mysidopsis bahia 9.55 48-hr Miscellaneous Oil Spill Control Agents 208 OIL SOLUTIONS POWDER ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 230°F 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: 0.91 5. pH: 4.08 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: None 9. Solubility in Water: Negligible X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <1.0 Cadmium <0.05 Chromium <0.325 Copper 17.25 Lead <0.08 Mercury 0.02 Nickel <0.225 Zinc <0.45 Cyanide <0.1 Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 209 OIL SOLUTIONS POWDER ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 7/23/2021 7/27/2022 TECHNICAL PRODUCT BULLETIN #M-26 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JUNE 30, 2008 "ELASTOL" (aka, SEPARATE, LIQUID ELASTOL) I. NAME, BRAND, OR TRADEMARK ELASTOL (aka, SEPARATE, LIQUID ELASTOL) Type of Product: Miscellaneous Oil Spill Control Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Action Additives, Inc. 205 Industrial Road P.O. Box 965 Ducktown, TN 37326 Phone: updated information required (Mr. Tim Kaylor) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Design Engineering Systems Analysis P.O. Box 293 Alexandria, VA 22313 Phone: (703)4613912 E-mail: escambos@actionadditivesinc.com (Mr. Ernest T. Scambos) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Autoignition temperature for product is 392°F. Product is combustible in liquid form and can form combustible mixtures and possibly explosive mixtures above the flash point. Use water spray to cool fire exposed surfaces and to protect personnel. Isolate "fuel" supple from fire. Use foam, dry chemical, or water spray to extinguish fire. Avoid spraying water directly into storage containers due to danger of boil over. Product is volatile and gives off invisible vapors. Either the liquid or vapor may settle in low areas or travel some distance along the ground or surface to ignition source where they may ignite. 2. Ventilation: Product is moderately volatile. Ensure proper ventilation. Avoid formation and inhalation of spray mist and vapors. Do not wear contaminated clothing. Keep away from fire and heated objects. Avoid formation of aerosols. Avoid squirting and use dosage pump when transferring. 3. Skin and eye contact; protective covering; treatment in case of contact: Protection depends on use and condition of work environment. Ensure good personal hygiene, wash hands regularly Miscellaneous Oil Spill Control Agents 210 ELASTOL ------- with soap and water. Avoid contact with skin and eyes and inhalation of fumes/aerosols. All new protective gear must be of CE standard. There must be an eye rinsing kit available at the work place. Where there is danger of inhalation, use mask with brown filter. If the product is sprayed and there is a risk of aerosol formation, use mask with combination filter A2-P2. When used regularly, measuring routines for solvent measurement should be implemented. Level of contamination should be kept as low as possible. 4.a. Maximum storage temperature: ~160°F 4.b. Minimum storage temperature: -100°F 4.c. Optimum storage temperature range: 40-70°F 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE At least 5 years when stored at temperatures below 150°F. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: ELASTOL can be applied to the surface of an oil/water separator tank or added to a waste stream before it enters a separation tank. ELASTOL floats on water, dissolving when it comes in contact with petroleum products (e.g., gasoline, diesel, jet fuel, fuel oil, crude, etc.). It remains effective for long periods, but naturally degrades when exposed to the atmosphere over longer periods. ELASTOL treated oil may increase the performance of containment and recovery equipment: • Containment booms - may have higher current and tow speed capability • Mechanical skimming equipment - may be improved 2 to 10 times its normal recovery rates • Drum skimmers - may recover little or no water with the oil When applied early to a spill, ELASTOL may reduce emulsification and dispersion of oil. In addition, it may reduce the penetration of oil into porous soils and sandy beaches. 2. Concentration/Application Rate: ELASTOL can be used at very low concentrations from 100- 1,500 ppm (0.01% to 0.15%). The amount of ELASTOL to be used is dependent upon the viscosity of the oil being removed. For example, one gallon of ELASTOL will remove: • 13 gallons of gasoline • 34 gallons of diesel • 84 gallons of medium oil • 150 gallons of heavy oil 3. Conditions for Use: ELASTOL may be used on fresh or salt water (under warm or cold temperatures). Prompt application may maximize effectiveness. The older the pollutants the few light oil elements remain in the oil, which may reduce the effectiveness of recovery. Miscellaneous Oil Spill Control Agents 211 ELASTOL ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested ELASTOL No. 2 Fuel Oil ELASTOL & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 1,333 96-hr 94 5.4 3.3 8.2 3.7 7.4 10.7 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 176°F 2. Pour Point: -71°F 3. Viscosity: 3.46 cSt @ 77°F 4. Specific Gravity: 0.83@t 60°F 5. pH: 6.8-7.0 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility in Water: Insoluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium ND Copper ND Lead ND Mercury ND Nickel ND Zinc 1.4 Cyanide ND Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 212 ELASTOL ------- TECHNICAL PRODUCT BULLETIN #M-27 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JUNE 03, 2010 "OIL BOND®" I. NAME, BRAND, OR TRADEMARK OIL BOND® Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Solidification Products International, Inc. P.O. Box 35 524 Forrest Road Northford, CT 06472 Phone: (203) 484-9494 Toll Free: (800) 758-3634 Fax:(203)484-9492 E-mail: dgannon@oilbarriers.com (Ms. Donna Gannon) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Solidification Products International, Inc. P.O. Box 35 524 Forrest Road Northford, CT 06472 Phone: (203) 484-9494 Toll Free: (800) 758-3634 Fax:(203)484-9492 E-mail: dgannon@oilbarriers.com (Ms. Donna Gannon) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Not classified as flammable, but will burn. Maintain a fire watch if OIL BOND® is heated above 450°F. 2. Ventilation: Normal ventilation is adequate. For confined space entry or lack of exhaust in a contained area, avoid generating dust. Dust in excessive concentration can result in an explosive mixture in air. Wear approved NIOSH respirator with particulate pre-filter for dust. 3. Skin and eye contact; protective covering; treatment in case of contact: Product dust may be mildly irritating to eyes and respiratory tract. Wear approved standard issue work clothes, gloves, dust mask, and dust tight goggles as needed. In case of contact with eyes, flush with water. If prolonged skin contact, wash with soap and water. For inhalation of dust, remove to fresh air. 4.a. Maximum storage temperature: 180°F 4.b. Minimum storage temperature: None Miscellaneous Oil Spill Control Agents 213 OIL BOND® ------- 4.c. Optimum storage temperature range: Ambient. Avoid elevated temperatures >200°F for extended periods of time. 4.d. Temperatures of phase separations and chemical changes: >450°F chance of auto- combustion. Avoid strong oxidizing agents. V. SHELF LIFE 5 years. Store OIL BOND® in cool, dry area away from direct sunlight to prolong shelf life. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: OIL BOND® will absorb and solidify hydrocarbon spills on freshwater and saltwater or land applications. For small spills, OIL BOND® may be broadcast by hand, and booms and pillows may be used to ring the spill. For large spills, OIL BOND® may be distributed by equipment with an air or water stream. Ground all dispensing equipment if deploying dry OIL BOND® at a high rate of speed to prevent static discharge. Introduce OIL BOND® with dispensing water spray just before final discharge to allow mixing of OIL BOND® with the water stream. Allow OIL BOND® contact time with the spilled fuel or hydrocarbon waste for 10 minutes to 1 hour before collection to allow absorption and solidification. Lighter fuels require less solidification time than heavier viscosity fuels such as No. 6 fuel oil or heavy crude. OIL BOND® is non-toxic and biologically inactive, and will remain floating on the surface of the water before and after solidification. Collect solidified materials with a net or vacuum equipment from the surface of the water. For land spills shovel, sweep, or vacuum solidified material. Place the solidified debris in approved, labeled, and sealed containers as required by local, state, federal, international, or country- specific regulations. Depending on the inherent nature of the spilled liquid that was solidified, disposal options include landfilling, incineration, waste to energy incineration, or use as a secondary fuel. 2. Concentration/Application Rate: OIL BOND® should be applied at a rate of 15% to 30% by weight to a spilled hydrocarbon liquid. Lighter viscosity hydrocarbon waste and oils require less OIL BOND® than heavier fuels. Conditions for use on spills may be highly variable, degraded product or extremely heavy viscosity fuels may require additional OIL BOND® to obtain complete solidification. 3. Conditions for Use: OIL BOND® may be used on any hydrocarbon waste, oil or fuel on freshwater, saltwater, or land applications. During rough weather with high winds or seas a conventional containment collection boom is recommended to corral the spill allowing easier retrieval and contact time with OIL BOND®. Cold water temperatures may require longer contact time to fully solidify a spill. Miscellaneous Oil Spill Control Agents 214 OIL BOND® ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested OIL BOND® No. 2 Fuel Oil OIL BOND® & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) >10000 96-hr >10000 48-hr 3.0 7.1 3.8 9.6 8.0 11.3 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: NA, solid product 3. Viscosity: NA, solid product 4. Specific Gravity: 0.21 5. pH: 8.8 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: Pigment/Antioxidant 9. Solubility in Water: Insoluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.6 Cadmium <0.32 Chromium <0.32 Copper 0.71 Lead <0.32 Mercury <0.07 Nickel 0.97 Zinc 0.32 Cyanide <0.50 Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 215 OIL BOND® ------- TECHNICAL PRODUCT BULLETIN #M-28 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: AUGUST 17, 2010 "AQUAFLEX®" I. NAME, BRAND, OR TRADEMARK AQUAFLEX® (OPEN-CELL ELASTOMERIC SORBENTS) Type of Product: Miscellaneous Oil Spill Control Agent (formerly OPFLEX®^ II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT AquaFlex Holdings LLC P.O. Box 355 West Hyannisport, MA 02672 Phone: (508) 345-6520 Fax: (508) 425-2990 E-mail: ssmith@aflx.com Website: www.aqflx.com (Mr. Scott Smith) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS AquaFlex Holdings LLC P.O. Box 355 West Hyannisport, MA 02672 Phone: (508) 345-6520 Fax: (508) 425-2990 E-mail: ssmith@aflx.com Website: www.aqflx.com (Mr. Scott Smith) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements. No special handling is required. 3. Skin and eye contact; protective covering; treatment in case of contact: No special equipment or clothing required. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous 4.b. Minimum storage temperature: No minimum 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable Miscellaneous Oil Spill Control Agents 216 AQUAFLEX® ------- V. SHELF LIFE Shelf life is unlimited when stored in plastic bags. VI. RECOMMENDED APPLICATION PROCEDURE 1. Example - AquaFlex foam is fabricated into 40 6-foot strips that are in mesh netting. These booms can be connected end-to-end and positioned behind containment booms to absorb oil that has breached the containment. 2. Example - AquaFlex foam is fabricated into 1/4" x 16" x 18" pads that can be deployed by placing on an oil patch to absorb the oil from the water surface. 3. Example - AquaFlex foam can be cut into small cubes such as 1 cubes and contained in a net or mesh tube to create a very high surface area absorbent boom. 4. Example - AquaFlex foam can be fabricated into mega pads of 1/4" x 1 foot x 6 foot sections to be connected on the back of a containment boom system to absorb oil which flows over the boom, especially in marsh areas. 5. Example - AquaFlex foam can be fabricated into multiple mops that are strung between support posts at the shoreline to remove oil from the surf. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested AQUAFLEX® No. 2 Fuel Oil AQUAFLEX® & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) >35640 96-hr 8630 48-hr 3.35 2.24 5.49 1.67 12.19 10.53 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: NA 2. Pour Point: NA, solid product 3. Viscosity: NA, solid product 4. Specific Gravity: 0.0415 g/mL 5. pH: NA 6. Surface Active Agents: NA 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL Miscellaneous Oil Spill Control Agents 217 AQUAFLEX® ------- 9. Solubility in Water: Insoluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.179 (brl) Cadmium <0.089 (brl) Chromium <0.268 (brl) Copper 1.74 Lead 0.286 Mercury <0.0031 (brl) Nickel <0.446 (brl) Zinc 139 Cyanide 0.498 Chlorinated Hydrocarbons <2.43 (brl) Miscellaneous Oil Spill Control Agents 218 AQUAFLEX® ------- TECHNICAL PRODUCT BULLETIN #M-29 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: AUGUST 17, 2010 "GELCO 200" I. NAME, BRAND, OR TRADEMARK GELCO 200 Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT UESS, Ltd. Box 6088 Drayton Valley, AB, Canada T7A 1R6 Phone: (780) 621-6870 E-mail: hugh.morrison@telus.net (Mr. Hugh Morrison) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS UESS, Ltd. Box 6088 Drayton Valley, AB, Canada T7A 1R6 Phone: (780) 621-6870 E-mail: hugh.morrison@telus.net (Mr. Hugh Morrison) *Currently only one distributor, which serves as a point of contact. IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: >150°F 2. Ventilation: Store in well-ventilated location. Where local exhaust ventilation is not practical and odors are detected, use a negative pressure half face respirator with a cartridge designed to protect against organic vapors and dust if also present, a particulate pre-filter should be used. For high airborne dust concentrations, use a cartridge to be used against nuisance dust. 3. Skin and eye contact; protective covering; treatment in case of contact: Use cloth gloves if desired. Dust-tight mono-glasses and standard issue work-wear. In case of contact with eyes or skin, flush with water. 4.a. Maximum storage temperature: 200°F 4.b. Minimum storage temperature: None 4.c. Optimum storage temperature range: 40-90°F 4.d. Temperatures of phase separations and chemical changes: Begins to oxidize exothermically at high temperatures (230°F). 4.e. Store in a cool, dry location. Away from direct sunlight or sources of intense heat. Miscellaneous Oil Spill Control Agents 219 GELCO 200 ------- 4.f. Maintain fire watch if material temperature reaches 536°F (280°C). 4.g. Product may accumulate static charge during processing, handling, and transport. Earth/ground all equipment used in handling and applying this product. 4.h. Avoid contact with strong oxidizing agents. 4.i. Do not stack Flexible Intermediate Bulk Containers or palletized bags. V. SHELF LIFE >10 years when stored in dry, cool area out of sunlight. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: For small scale spills on water (fresh or salt), GELCO 200 can be broadcast directly onto the spill by hand or small hand held spreader from the outer edge back into the middle of the spill. Agitation is not necessary for GELCO 200 to be effective. The product can also be used and is available in booms, socks, and pillows. For large spills on water (fresh or salt), GELCO 200 may be deployed with an air or water stream directed at the leading edge of the spill. Dispensing equipment should be properly grounded to prevent static electricity build-up if pumping GELCO 200 in dry form at high rates of delivery. If used with a water carrying media, product will require agitation to keep product suspended if there is a delay or travel time associated between batching and delivering product upon spill. GELCO 200 will remove oils and other hazardous hydrocarbon based materials from both salt and fresh water. GELCO 200 encapsulates and solidifies the oil, and remains buoyant even after total saturation. The solidified products can be removed from the water with hand vacs, vacuum barges, commercial fishing nets, and conveyors. Solidified materials should be placed into appropriate containers and disposed of in accordance with all applicable federal, state, and local regulations. Land Application For spills on land, the product would be applied in the same manner. The product can also be applied by sand-blasting equipment/hopper or pneumatic air seeders. Agitation is not necessary in most scenarios. Some fine agitation may be necessary to remove contaminated materials from native grasses and marsh areas. Many factors are taken into consideration before determining the best method(s) of application. They include weather, geography, access, land use, and habitat of affected spill area. When removing contaminants from land, it should be a priority to minimize the volume of land taken to preserve the integrity of the land and to minimize the volume of waste requiring disposal. To recover solidified oil or hazardous materials from spills on land, the solidified product can be collected and removed efficiently and effectively using a variety of manual and mechanical Miscellaneous Oil Spill Control Agents 220 GELCO 200 ------- means. Manual methods include picking up by hand, using brooms, rakes, shovels, and squeegees to remove and pick up solidified petroleum waste product. Mechanical means include using hand held vacuums, portable vac units, vac-trucks, or commercial shop vacs. Once the spilled product is solidified by GELCO 200, it will not leach. GELCO 200 is extremely hydrophobic and will not take on water, which may help to keep the volume of waste produced down, depending on the characterization of any non-solidified oil and water remaining in the area treated. Pressure flushing the solidified product or raw into a containment area where it can be solidified - a boomed area, containment dike, bell hole, etc. for removal by vacuum - is also a very practical method for removal. Land spill cleanup of solidified oil/product Collection and disposal of materials generated from application to oil spilled on land involve greater variation in waste composition, and appropriate disposal techniques have to be selected for the particular circumstances. Proper precautions, including testing as necessary to identify the characteristics of wastes generated from the application of GELCO 200, should be taken to determine the safe and legally required means of recovering, handling, storing, transporting, treating, recycling, or disposing of materials produced from the application of GELCO 200 to oil spilled on land. All materials should be placed into appropriate containers, characterized by knowledge or testing as to waste type, and handled, stored, transported, treated, or disposed of in accordance with all applicable federal, state, and local regulations. Professional advice should be obtained where needed. 2. Concentration/Application Rate: GELCO 200 is usually applied at a ratio of 5-20% of GELCO 200 to waste by weight to solidify light, medium, and heavy hydrocarbons. Solidification typically occurs 1-3 minutes for most oils. GELCO 200 has been used effectively on heavier crudes including Bunker C within the application rates noted above. 3. Conditions for Use: GECLO 200 is effective in all environments and under a broad range of weather conditions. The product is most effective on water temperatures between 32°F and 120°F. Depending upon the age and/or viscosity of the material, varying amounts of GELCO 200 may be required to obtain complete solidification. The recovered solidified product can be disposed of in landfills, incinerated, or disposed of in accordance with all applicable federal, state, and local regulations. Some products can be recovered from the solidified mass through a heat process that would allow the solidified product to release itself from the GELCO 200. UESS, Ltd. has had TCLP tests completed on several occasions and have not had any field instances of product being released in our methods of recovery and disposal to date due to pressure related issues. Miscellaneous Oil Spill Control Agents 221 GELCO 200 ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested GELCO 200 No. 2 Fuel Oil GELCO 200 & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) >10000 96-hr >1000 9.26 6.58 3.15 3.51 8.03 14.5 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >150°F 2. Pour Point: NA, solid product 3. Viscosity: NA, solid product 4. Specific Gravity: 0.25 g/cm3 at 4°C 5. pH: 4.75 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: CONFIDENTIAL 9. Solubility in Water: Insoluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.577 Cadmium <0.289 Chromium <0.577 Copper <0.577 Lead <0.577 Mercury <0.100 Nickel 5.91 Zinc 0.788 Cyanide ND Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 222 GELCO 200 ------- LAST COMMUNICATION WITH MANUFACTURER: 1/10/2017 LAST ATTEMPT: 7/27/2022 TECHNICAL PRODUCT BULLETIN #M-30 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: APRIL 26, 2012 "NORSOREX® APX" I. NAME, BRAND, OR TRADEMARK NORSOREX® APX Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT D-NOV GmbH Perfektastrasse 86 A-1230 Vienna Austria, Europe Office: updated information required Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Mr. Gerhard Karall, COO) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS D-NOV GmbH Perfektastrasse 86 A-1230 Vienna Austria, Europe D-NOV GmbH Perfektastrasse 86 A-1230 Vienna Austria, Europe Office: updated information required Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Mr. Gerhard Karall, COO) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: >174°F 2. Ventilation: Dust explosions are possible while handling organic powders at high Miscellaneous Oil Spill Control Agents 223 NORSOREX® APX ------- concentrations; therefore, provide proper air ventilation with fresh air or other methods to avoid dust formation. General dust limits (DE-TRGS 900): 3 mg/m3 (respirable dust fraction), 10 mg/m3 (inhalable dust fraction), short-term exposure value (TRGS 900, 2.3) - excess factor 4. For short-term exposure wear dust masks. 3. Skin and eye contact; protective covering; treatment in case of contact: Avoid contact to skin and eyes. Do not breathe dust. Wear protective goggles, gloves, and clothing. Following skin contact, wash with plenty of water and pH-neutral soap. Obtain medical attention if irradiation symptoms persist. Following eye contact, remove contact lenses immediately and rinse with plenty of water (also under the eyelids) for at least 15 minutes. Obtain medical attention. Following ingestion, remove all of product from the respiratory system and wash oral cavity. Drink 200-300 ml of water. Do not induce vomiting without medical advice. Obtain medical attention. 4.a. Maximum storage temperature: 45°C/113°F 4.b. Minimum storage temperature: -5°C/23°F 4.c. Optimum storage temperature range: -5°C to 30°C/23°F to 86°F 4.d. Temperatures of phase separations and chemical changes: The material composition does not change with the temperature (no phase separation). Chemical changes occur at temperatures >45°C/113°F with oxygen. The material changes from white to yellow and the absorption behavior decreases. V. SHELF LIFE Shelf life is 3 years from date of production. Keep material stored in original containers in a dark, dry area until use. The product should be used within 6 months after opening the original container. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: NORSOREX® APX is a special polymer with very high affinity for hydrocarbons and, since it is hydrophobic, it is also insoluble in water. NORSOREX® APX can be used in free powder or pad form (sealed bags containing the powder). NORSOREX® APX powder can bond to a variety of liquid hydrocarbons in two stages. First, due to the fast absorption process further oil spreading is prevented (forming of a gel). Second, the oil solidifies to a non-leaching inert, firm cohesive "rubber-like" mass within a few hours, which can be easily collected and burned, disposed of or used for other purposes (e.g., rubber industry in a full green recycle process). It is a combination of an adsorption and absorption process. Use NORSOREX® APX powder or pads by estimating the hydrocarbon quantity and checking with the application chart to individuate the necessary quantity. The suggestion to optimize the usage is to keep ratio values of NORSOREX® APX to hydrocarbon as close as possible to the application chart. If possible, use pretests to test the process. Deploy NORSOREX® APX in the environment where there is hydrocarbon to be removed or recovered. NORSOREX® APX can be applied by hand or through mechanical spreading. According to the desired performance, wait the necessary reaction time. Reaction takes place within minutes and it reaches 80 percent of its efficiency after only a few hours. Maximum efficiency (100 percent) can be reached in less than 24 hours. Once NORSOREX® APX has reacted, it is possible to recover the hydrocarbon in solid Miscellaneous Oil Spill Control Agents 224 NORSOREX® APX ------- form. 2. Concentration/Application Rate: Type of Hydrocarbon (HC) kgHc/kgAP X kgAPx/kgH c kgAPx/m3H c Lhc/Lap X Lapx/Lh c Benzene 23.0 0.043 38.1 9.189 0.109 Toluene 18.0 0.056 48.2 7.267 0.138 Hexane 4.2 0.238 155.9 2.245 0.445 Heptane 5.0 0.200 135.9 2.575 0.388 Cyclorhexane 6.8 0.147 114.6 3.055 0.327 Di chl orom ethane/Methyl ene chloride 18.0 0.056 73.9 4.737 0.211 Chloroform 26.0 0.038 57.0 6.136 0.163 T ri chl oroethane/T ri chl oroethy 1 en e 31.8 0.031 45.9 7.623 0.131 Tetrachl oroethene/Tri chl oroethy 1 ene 31.0 0.032 52.3 6.689 0.149 1,2-Dichlorobenze 27.4 0.036 47.4 7.377 0.136 Pyralene 60 (60% PCB/40%TCB) 36.4 0.027 39.3 8.909 0.112 Pyralene 78 (78% PCB/22% TCB) 28.8 0.035 52.4 6.675 0.150 Diethyl glycol 2.7 0.370 3.11.1 1.125 0.889 Diocytlphthalate 2.8 0.357 353.9 0.990 1.010 Heavy Crude Oil A 12.0 0.083 75.0 4.667 0.214 Heavy Crude Oil B 9.0 0.111 88.9 3.938 0.254 Light Crude Oil 9.5 0.105 88.4 3.958 0.253 Kerosene 10.2 0.098 79.4 4.407 0.227 Diesel 10.0 0.100 82.3 4.253 0.235 Aromatic Process Oils 8.3 0.120 120.5 2.905 0.344 Naphthenic Process Oils 8.3 0.120 108.4 3.228 0.310 Paraffinic Process Oils 4.0 0.250 217.5 1.609 0.621 Refrigerator Oils 10.7 0.093 81.3 4.305 0.232 Turbine Oils 4.3 0.233 209.3 1.672 0.598 Machine Oils 4.5 0.222 200.0 1.750 0.571 Motor Oils 3.8 0.263 228.9 1.529 0.654 Vegetable Oils 2.7 0.370 337.0 1.038 0.963 HC - Hydrocarbon APX - NORSOREX® APX kgxx - Kilogram of xx M3xx - Cubic meters of xx Lxx - Liter of xx kgAPX./m3HC - Kilograms of NORSOREX® APX per cubic Bulk density of NORSOREX® APX powder: 0.35 g/cm3 The results are tested at room temperature (23°C/73°F) and most substrates show an improvement of 10 until 15% at Miscellaneous Oil Spill Control Agents 225 NORSOREX® APX ------- Type of Hydrocarbon (HC) kgHc/kgAP X kgAPx/kgH c kgAPx/m3H c Lhc/Lap X Lapx/Lh c meter of hydrocarbon 40°C. The best performance is achieved at 60°C with an improvement of about 30%. At higher temperatures the effect of improvement falls and over 100°C significant. 3. Conditions for Use: To recover the solidified NORSOREX® APX from the environment, mechanically collect the material and transport it to the nearest designated disposal location. NORSOREX® APX has the capability of 3.5 bar of pressure before it will start leaking. Do not discharge into drains, surface waters, or ground waters. NORSOREX® APX is not biodegradable. The resulting "rubber-like" material could still be hazardous so extreme caution should be exercised when handling these materials. Very polar substances such as organic acids, alcohols or glycols show a reduced absorption efficiency of the product. The water temperature has an influence on the reaction time. Cold water slows down the solidification process. The ages of pollutants only have an influence on the absorption performance if their viscosity or polarity are increased to the typical values for the "fresh" pollutant. Avoid damage to NORSOREX® APX pads if the application environment is characterized by rough water. This will ensure the easiest deployment and recovery procedure. If allowed by current regulations and if properly contained, the free powder form is recommended to optimize the contact interface between NORSOREX® APX and the liquid hydrocarbon. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested NORSOREX® APX No. 2 Fuel Oil NORSOREX® APX & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) >100,000.00 96-hr >100,000.00 48-hr 15.10 96-hr 2.41 48-hr 39.80 96-hr 3.06 48-hr 2.01 96-hr 6.63 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Miscellaneous Oil Spill Control Agents 226 NORSOREX® APX ------- IX. PHYSICAL PROPERTIES 1. Flash Point: 174°F 2. Pour Point: NA 3. Viscosity: NA 4. Specific Gravity: 0.91047 at 60°F 5. pH: 7.10 6. Surface Active Agents: Polynorbornene 7. Solvents: NA 8. Additives: Phenolic antioxidant, flow agent 9. Solubility in Water: Insoluble in water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium 0.40 Copper 0.14 Lead ND Mercury 0.011 Nickel ND Zinc 55.40 Cyanide 0.222 Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 227 NORSOREX® APX ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #M-31 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 9, 2015 "CAS 100®" I. NAME, BRAND, OR TRADEMARK CAS 100® Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Tradewinds Environmental Safety Services SA de CV Calle 1 "E" No. 245 por 30 y 36 Col. Campestre Merida, Mexico C.P 97120 Phone: updated information required E-mail: updated information required (Mr. Michael Harper) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS EPC Evolved Products, Inc. 5889 Greenwood Plaza Boulevard, Suite 201 Greenwood Village, CO 80111 Phone: 720-496-0023 E-mail: dave.washington@epces.com (Mr. Dave Washington) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-Flammable 2. Ventilation: Work in well ventilated area. Avoid excessive inhalation of fine particles. 3. Skin and eye contact; protective covering; treatment in case of contact: Avoid contact to eyes. Do not breathe in particles. Wear protective goggles, gloves and clothing. Following skin contact, wash with plenty of soap and water. Remove exposed or contaminated clothing, taking care not to contaminate the eyes. Please seek medical attention if adverse effects continue after flushing. Following eye contact, remove contact lenses (if necessary) and rinse with gently running water for at least 15 minutes. Obtain medical attention. Following ingestion, call physician or poison control center for most current information. If professional advice is not available, do not induce vomiting. Drink large quantities of water. Following inhalation, move to fresh air location. Seek medical attention if adverse symptoms continue after removal to fresh air. 4.a. Maximum storage temperature: 140°F 3/10/2016 7/27/2022 Miscellaneous Oil Spill Control Agents 228 CAS 100® ------- 4.b. Minimum storage temperature: -40°F 4.c. Optimum storage temperature range: -40°F to 140°F 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE The shelf life of CAS 100® is 1 year from date of production if stored in a dry dark location. Keep material stored in original containers in a dark, dry area until use. If the product is exposed to UV rays consistently, it will degrade over time. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: In powder form, apply CAS 100® along the outer edges of spill area to prevent migration. Continue to apply CAS 100® inside spill area until the area is saturated with product. Depending on type of hydrocarbon, the resulting oil/CAS 100® mixture can be rolled up like a carpet or clumps of the solid can be removed with a net. In pad form, booms can be used to prevent migration of oil spill. Pads can be used to clean up the spill area by placing them on the oil spill itself. Once the pad is saturated, it can be easily removed by simply picking up the pad. 2. Concentration/Application Rate: CAS 100® is used by applying 1 pound of product to each 10 pounds of spilled hydrocarbon. The contact time varies from just a few seconds to several hours depending upon the quantity of the spill. Hydrocarbon viscosities decrease as temperatures increase causing an increase in the time required for the gelling process of hydrocarbon to CAS 100®. 3. Conditions for Use: CAS 100® can be used on any concentration of water salinity and water temperature. There is no restriction of the types of ages of the hydrocarbon being processed. Depending upon the types of the hydrocarbon, the resulting CAS 100®/oil mixture can be in the form of a carpet, rubber ball or crumb like material. CAS 100® has a fast gelling characteristic, which prevents the hydrocarbon from spreading further. Once the hydrocarbon comes in contact with CAS 100®, the result is a non-leaching solid within a few minutes (or hours) depending on the size of the spill. The resulting solid should be collected at the spill site and disposed of according to federal, state and local regulations. Collecting the solid at the spill site will prevent the resulting CAS 100®/oil mixture from reaching open water. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested CAS 100® Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) >1000 96-hr >1000 48-hr 4.81 96-hr 1.93 48-hr 5.94 96-hr 1.41 48-hr 8.84 96-hr 23.00 48-hr No. 2 Fuel Oil CAS 100® & No. 2 Fuel Oil Menidia beryllina (1:10) Reference Toxicant (SDS) Mysidopsis bahia Menidia beryllina Mysidopsis bahia Miscellaneous Oil Spill Control Agents 229 CAS 100® ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: NA (solid material) 3. Viscosity: NA (solid material) 4. Specific Gravity: 0.51 5. pH: 6.94 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: NA 9. Solubility in Water: Insoluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <2.0 Cadmium <0.5 Chromium <1.0 Copper <2.5 Lead <2.0 Mercury <0.029 Nickel <4.0 Zinc <5.0 Cyanide <0.22 Chlorinated Hydrocarbons ND Miscellaneous Oil Spill Control Agents 230 CAS 100® ------- TECHNICAL PRODUCT BULLETIN #M-32 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: APRIL 21, 2016 "S-200 OILGONE®" I. NAME, BRAND, OR TRADEMARK S-200 OILGONE® Type of Product: Miscellaneous Oil Spill Control Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT RBL Environmental, LLC* 1311 Dorothy Avenue Phoenixville, PA 19460 Phone: (610) 520-7665 E-mail: iim.lynn@iepusa.com (Mr. James Lynn) (*RBL Environmental, LLC is the manufacturer and marketer for International Environmental Products) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS RBL Environmental, LLC 1311 Dorothy Avenue Phoenixville, PA 19460 Phone: (610) 520-7665 E-mail: iim.lynn@iepusa.com (Mr. James Lynn) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-Flammable 2. Ventilation: Ensure good ventilation. This can be achieved by local suction and or general air extraction. If this is insufficient to maintain the concentration under Workplace Exposure Limits (WEL), suitable breathing protection should be worn. Applies only if maximum permissible exposure values are listed below. Respiration protection normally not necessary. If Occupational Exposure Standards (OES) or Maximum Exposure Limits (MELs) are exceeded, use appropriate air purifying respirator with filter. EXPOSURE CONTROL/PERSONAL PROTECTION Exposure limit values: Not applicable Name WEL-TWA WEL-STEL Content 2-(2-butoxyethoxy)-ethanol 10 ppm 15 ppm 1-5% Butyl carbitol® (67.5 mg/m3) (101.2 mg/m3) (WEL, EC) (WEL, EC) WEL-TWA: Workplace Exposure Limit-Time-Weighted Average; WEL-STEL: Workplace Exposure Limit-Short-Term Exposure Limit; EC: European Commission 3. Skin and eye contact; protective covering; treatment in case of contact: General hygiene Miscellaneous Oil Spill Control Agents 231 S-200 OILGONE® ------- measures for the handling of chemicals are applicable. Wash hands before breaks and at end of shift. Keep away from food, drink and animal feeding supplies. Skin Protection: wear protective work garments (e.g., safety shoes, long-sleeves). Wear chemical resistant protective gloves; or if applicable, gloves made of protective neoprene or butyl rubber. Protective hand cream is recommended. Eye Protection: wear tight fitting protective goggles with side protection. 4.a. Maximum storage temperature: 132°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 55°F to 85°F 4.d. Temperatures of phase separations and chemical changes: <0°F and >212°F. Phase separation will be eliminated when returning to ambient temperatures. V. SHELF LIFE Recommended shelf life is 10 years if product is kept in the unopened, original container. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: S-200 OILGONE® is a water like liquid and can be sprayed with traditional liquid spraying equipment, such as pressurized sprayers or backpack sprayers. Apply product directly to the hydrocarbon. 2. Concentration/Application Rate: The recommended application rate for spraying on the spill is approximately 1:1 by weight of the product as compared to the hydrocarbon being agglomerated. For example, use 1 gallon of product for every 1 gallon of hydrocarbon to be treated. For sheens, apply 1 gallon of product for every 8 square yards of surface area. 3. Conditions for Use: S-200 OILGONE® is a hydrocarbon coagulator used for the cleanup of hydrocarbon spills on water. These hydrocarbons include, but are not limited to, gasoline, No. 2 to No. 6 Fuel Oil, jet fuels, kerosene, lubricating oils, hydraulic oils and crude oils. Once applied, the hydrocarbon will agglomerate with S-200 OILGONE® and remain on the water's surface. To prevent the hydrocarbon or agglomeration from reaching open water during application, use traditional booms to contain the spill. The agglomeration will form gel like balls, eliminating the sheen and allowing for the product:oil mixture to be removed from the water's surface using traditional skimming tools. The resulting gel like balls should be collected at the spill site and disposed of according to federal, state and local regulations. S-200 OILGONE® can be used in salt, brackish or fresh water. The product can be applied at any ambient temperature on any hydrocarbon pollutant whether fresh or weathered. The size of the gel balls will be dependent on the quantity (not type) of hydrocarbon spilled. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested S-200 OILGONE® No. 2 Fuel Oil S-200 OILGONE® & No. 2 Fuel Oil (1:10) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 326.22 96-hr 47.29 48-hr 21.11 96-hr 2.56 48-hr 15.83 96-hr 2.46 48-hr Miscellaneous Oil Spill Control Agents 232 S-200 OILGONE® ------- LC50 (ppm) 3.47 96-hr 4.91 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Material Tested Species Reference Toxicant (SDS) Menidia beryllina Mysidopsis bahia IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: 29 °F 3. Viscosity: 6.9 cst@40°C 4. Specific Gravity: 0.9796 5. pH: 7.01 6. Surface Active Agents: Confidential 7. Solvents: Confidential 8. Additives: Confidential 9. Solubility in Water: Miscible X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.5 Cadmium <0.25 Chromium <0.25 Copper <0.5 Lead <0.6 Mercury <0.0025 Nickel <0.5 Zinc 0.54 Cyanide <0.025 Chlorinated Hydrocarbons <0.1 Miscellaneous Oil Spill Control Agents 233 S-200 ------- TECHNICAL PRODUCT BULLETIN #M-33 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: AUGUST 22, 2016 "HYDRO-BOND™" I. NAME, BRAND, OR TRADEMARK HYDRO-BOND™ Type of Product: Miscellaneous Oil Spill Control Agent - Solidifier II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Oil Spill Solutions, LLC 153 Foster Street Center, TX 75935 Phone: (936) 598-6595 Fax: (936) 598-6338 E-mail: fred@,fredwulf.com Website: www.oilspillsolutionsllc.com (Mr. Fred Wulf) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Oil Spill Solutions, LLC 153 Foster Street Center, TX 75935 Phone: (936) 598-6595 Fax: (936) 598-6338 E-mail: fred@,fredwulf.com Website: www.oilspillsolutionsllc.com (Mr. Fred Wulf) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-Flammable (DOT: Non-Hazardous) 2. Ventilation: Personal protective equipment should be used when applying Hydro-Bond™. Recommended equipment would include safety glasses or goggles, disposable respirators, nuisance dust mask or procedural mask, disposable gloves and long sleeves. Odors/vapors may produce mild and temporary discomfort to the respiratory tract resulting in wheezing, tightness in the chest, shortness of breath and coughing. Although they may be present in low amounts, dust and small pieces of material may aggravate bronchitis, asthma, and emphysema if inhaled. 3. Skin and eye contact; protective covering; treatment in case of contact: Hydro-Bond™ in contact with the skin may result in irritation (redness, itching) or other effects with some individuals. In case of skin contact wash exposed skin thoroughly with soap and water. As some are sensitive or allergic to natural rubber (Latex), if irritation develops and is prolonged and/or sore, consult a physician. Hydro-Bond™ material is abrasive if it enters the eye, which can cause irritation to sever damage if left untreated. In case of eye contact flush eyes with plenty of water Miscellaneous Oil Spill Control Agents 234 HYDRO-BOND™ ------- for at least 15 minutes. Avoid rubbing the eye. If experiencing prolonged irritation or soreness, seek medical attention. In the event that Hydro-Bond™ is ingested there may be irritation of mucus membranes of mouth, throat, esophagus and stomach along with nausea may occur. Abrasion to the mouth, esophagus, stomach and intestinal tract may occur. If inhaled, in emergency situations, use proper respiratory protection and immediately remove the affected person from the exposure. Keep at rest. Administer artificial respiration if breathing has stopped. Seek medical attention. If swallowed do not induce vomiting. Rinse mouth well with water. Never give anything by mouth to an unconscious person. Seek medical attention. Repeated unprotected exposure to Hydro-Bond™ may result in sensitization to susceptible individuals. General advice: If negative symptoms develop while handling the product, move out of the area to prevent further exposure. Consult a physician as a precautionary measure if symptoms develop after being subjected to unprotected exposure of the material. If eye or skin irritation occurs flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Unlimited in sealed poly drums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Product is best used in contained systems such as barriers, socks, mats, blankets, etc. Containment systems should be fully deployed before the application of Hydro- Bond™ to better facilitate rapid and complete recovery. For smaller spills a drum pump with sprayer and large orifice may be used to apply the Hydro-Bond™ material, mixing with salt or fresh water, depending on the spill being in salt or fresh water, as required depending on the type and viscosity of oil being treated. Aged hydrocarbon pollutants will tend to be more concentrated and more viscous; this may require additional quantities of Hydro-Bond™ to be applied. A higher viscosity hydrocarbon spill will require higher concentrations of Hydro-Bond™ and longer dwell times to ensure maximum absorption. 2. Concentration/Application Rate: In contained spills, product may be applied directly to water- borne spills on a 1:18 ratio by weight or a 1:1 ratio by volume. On heavy oils use Product directly on the spill with a 1:1 ratio by volume of spilled contaminant. 3. Conditions for Use: Effective in salt water or fresh water, with no limitation as to usage within optimum temperature parameters (application may be made at or above 30°F). In applications wherein the salinity of the water is higher in content, application of Hydro-Bond™ should be targeted more accurately to the spill concentrations as the hydrocarbon pollutant will be concentrated closer to the surface and effort should be made to ensure that the exposed pollutant is covered to the greatest extent possible. After treatment with Hydro-Bond™, residue should be collected by means of surface skimmers, vacuum pumps, skimming booms, etc. and removed from the site. The specific collection process and methodologies should be determined by on-site coordinator based on practices of the area and available equipment. Collected residue should be disposed of in accordance with local, state, and federal regulations. Miscellaneous Oil Spill Control Agents 235 HYDRO-BOND™ ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) HYDRO-BOND™ Menidia beryllina 6544.77 96-hr Mysidopsis bahia 5000.00 48-hr No. 2 Fuel Oil Menidia beryllina 41.81 96-hr Mysidopsis bahia 5.88 48-hr HYDRO-BOND™ & No. 2 Menidia beryllina 19.93 96-hr Fuel Oil (1:10) Mysidopsis bahia 1.93 48-hr Reference Toxicant (SDS) Menidia beryllina 7.52 96-hr Mysidopsis bahia 5.47 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: N/A 3. Viscosity: N/A 4. Specific Gravity: 0.9524 @60°F 5. pH: N/A 6. Surface Active Agents: N/A 7. Solvents: N/A 8. Additives: None 9. Solubility in Water: Not soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <2.0 Cadmium <1.0 Chromium 6.07 Copper 69.0 Lead 53.5 Mercury <0.020 Nickel 2.16 Zinc 4140 Cyanide <0.118 Chlorinated Hydrocarbons <80 (ug) Miscellaneous Oil Spill Control Agents 236 HYDRO-BOND™ ------- TECHNICAL PRODUCT BULLETIN #M-34 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: APRIL 16, 2021 "AQUAPAL®" I. NAME, BRAND, OR TRADEMARK AQUAPAL® (OPEN-CELL POLYOLEFIN FOAM SORBENT) Type of Product: Miscellaneous Oil Spill Control Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Palziv North America 7966 NC 56 Highway Louisburg, NC 27549 Phone: (508) 345-6520 Fax: (919) 496-2523 E-mail: ssmith@aqflx.com Website: www.palzivna.com (Mr. Scott Smith) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Palziv North America 7966 NC 56 Highway Louisburg, NC 27549 Phone: (919) 497-0010 Fax: (919) 496-2523 E-mail: tlehnartz@palzivna.com Website: www.palzivna.com (Mr. Tom Lehnartz) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous). 2. Ventilation: No special requirements. No special handling is required. 3. Skin and eye contact; protective covering; treatment in case of contact: No special equipment or clothing required; however, at all times, from deployment to reuse to disposal of AquaPal®, it is recommended that deployment personnel wear appropriate personal protective equipment including, but not limited to, impervious gloves, goggles, face masks/shields (as necessary that be dependent upon local air quality testing), and Tyvek suits. If eye or skin irritation occurs, flush with plenty of fresh water. Depending upon the type of spill and specific oil spilled, there may be supplemental safety requirement at the spill site. It is strongly recommended that deployment personnel follow all health and safety recommendations established for the spill site. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days. 4.b. Minimum storage temperature: No minimum 4.c. Optimum storage temperature range: 40°F to 120°F Surface Collecting Agents 237 Surface Collecting Agents ------- 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Shelf life is unlimited when stored in plastic bags. VI. RECOMMENDED APPLICATION PROCEDURE Mechanism of Action: AquaPal® is an open-cell foam manufactured in continuous rolls from polymers that are naturally oleophilic (and thus water repellant/hydrophobic). AquaPal® is deployed in roll form and/or fabricated into various configurations (e.g., eelgrass, pads, netted booms). When placed in an environment of oil and water, AquaPal® attracts oil and repels water. The open-cell structure provides capillaries for the oil to fill, and oil travels into the foam structure by capillary action. AquaPal® should be removed from the spill environment when the products are saturated with oil; and the oil should be disposed of according to federal, state, and local regulations. The following are examples of various product configurations of AquaPal®: • Example - AquaPal® foam rolls with thickness of 1/4 - 3/8 inches, widths of 20 to 60 inches, and lengths of 2 - 100 feet can be deployed directly on an oil patch/slick to absorb the oil from the water surface. • Example - AquaPal® foam is fabricated into 10-foot strips to make round, netted booms. These booms can be connected end-to-end and positioned in front and/or behind containment booms to absorb oil that has breached the containment. • Example - AquaPal® foam is fabricated into 3/8-inch-thick x 1/2-inch-wide x 6-inch-long pads that can be deployed by placing on an oil patch to absorb the oil from the water surface. • Example - AquaPal® foam can be cut into small strips such as 3/8-inch-thick x 1/2-inch-wide x 6 inches long and contained in a net or mesh bag to create a high surface area oil absorbent filter bag. • Example - AquaPal® foam can be fabricated into eelgrass configurations of 5-foot sections with a rope and carabiner clips at each end with eelgrass blades of 3/8-inch-thick x 3/4- inches wide x 18 inches long to be connected on the back of a containment boom systems to absorb oil which flows over or under the boom, especially in marsh areas and other sensitive ecosystems. Surface Collecting Agents 238 Surface Collecting Agents ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested AQUAPAL® No. 2 Fuel Oil AQUAPAL® & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 3134.10 96-hr >17040.00 48-hr 18.84 96-hr 3.40 48-hr 17.76 96-hr 3.56 48-hr 3.56 96-hr 7.02 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point (ASTM D-56): >212°F 2. Pour Point: NA, solid product 3. Viscosity: NA, solid product 4. Specific Gravity (ASTM D-792): 0.386 g/mL 5. pH: NA 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: CONFIDENTIAL 9. Solubility in Water: Not soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <3.86 (mg/L) Cadmium <0.725 (mg/L) Chromium <1.70 (mg/L) Copper 1.90 (mg/L) Lead <1.21 (mg/L) Mercury <0.0036 (mg/L) Nickel 0.954 (mg/L) Zinc 16.3 (mg/L) Cyanide 0.02 (mg/L) Chlorinated Hydrocarbons <5.00 (mg/L) Surface Collecting Agents 239 Surface Collecting Agents ------- SURFACE COLLECTING AGENTS: TECHNICAL NOTEBOOK BULLETINS Surface Collecting Agents 240 Surface Collecting Agents ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 3/14/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #S-5 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JUNE 29, 2012 "THICKSLICK 6535" I. NAME, BRAND, OR TRADEMARK THICKSLICK 6535 Type of Product: Surface Collecting Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Desmi, Inc. 1119 Cavalier Boulevard Chesapeake, VA 23323 Phone: updated information required E-mail: pla@desmi.com Website: http ://www.desmi.com (Mr. Peter Lane) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Desmi, Inc. 1119 Cavalier Boulevard Chesapeake, VA 23323 Phone: updated information required Phone: (716) 662-0632 E-mail: pla@desmi.com Website: http://www.desmi.com (Mr. Peter Lane) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO - Non-Flammable; DOT - Non-Hazardous 2. Ventilation: Use with ventilation equal to unobstructed outdoors in a moderate breeze 3. Skin and eye contact; protective covering; treatment in case of contact: May produce eye irritation in some persons and produce eye damage 24 hours or more after instillation. May cause skin irritation after prolonged or repeated exposure. Avoid skin and clothing contact. If skin contact occurs, immediately wash with large amounts of soap and water (if possible). Remove any contaminated clothing and shoes. Launder before reusing. If irritation persists, seek medical assistance. For areas where contact is likely, wear long sleeve shirt, chemical resistant gloves, and chemical resistant goggles. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: -40°F 4.c. Optimum storage temperature range: 59°F to 77°F Surface Collecting Agents 241 THICKSLICK 6535 ------- 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE Minimum of three years in unopened container. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spray on water around the perimeter of an oil slick using a pressurized backpack sprayer or aerial applicator. 2. Concentration/Application Rate: 6.4 U.S. gallons/mile (or 15L/km). 3. Conditions for Use: THICKSLICK 6535 is designed to aid in situ burning of free oil in calm water with drift ice where fire boom would be ineffective. When sprayed on the water around the perimeter of an oil slick, THICKSLICK 6535 will concentrate the oil to a thickness suitable for igniting a burn. It works in all water temperatures and salinities and works best with fluid petroleum that has not weathered significantly. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested THICKSLICK 6535 No. 2 Fuel Oil THICKSLICK 6535 & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 138 96-hr 286 48-hr 37.6 96-hr 2.43 48-hr 5.91 96-hr 1.53 48-hr 3.02 96-hr 8.23 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >180°F 2. Pour Point: 21.2 °F 3. Viscosity: 118 SUS at 100 °F 4. Specific Gravity: 0.9745 at 60°F 5. pH: 6.45 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: None 9. Solubility in Water: Partly miscible Surface Collecting Agents 242 THICKSLICK 6535 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) ND ND ND ND ND ND ND ND ND ND Surface Collecting Agents 243 THICKSLICK 6535 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 3/14/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #S-6 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JUNE 29, 2012 "SILTECH OP-40" I. NAME, BRAND, OR TRADEMARK SILTECH OP-40 Type of Product: Surface Collecting Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Desmi, Inc. 1119 Cavalier Boulevard Chesapeake, VA 23323 Phone: updated information required E-mail: pla@desmi.com Website: http ://www.desmi.com (Mr. Peter Lane) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Desmi, Inc. 1119 Cavalier Boulevard Chesapeake, VA 23323 Phone: updated information required E-mail: pla@desmi.com Website: http://www.desmi.com (Mr. Peter Lane) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO - Non-Flammable; DOT - Non-Hazardous 2. Ventilation: Use with ventilation equal to unobstructed outdoors in a moderate breeze 3. Skin and eye contact; protective covering; treatment in case of contact: May produce eye irritation in some persons and produce eye damage 24 hours or more after instillation. May cause skin irritation after prolonged or repeated exposure. Avoid skin and clothing contact. If skin contact occurs, immediately wash with large amounts of soap and water (if possible). Remove any contaminated clothing and shoes. Launder before reusing. If irritation persists, seek medical assistance. For areas where contact is likely, wear long sleeve shirt, chemical resistant gloves, and chemical resistant goggles. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: -40°F 4.c. Optimum storage temperature range: 59°F to 77°F 4.d. Temperatures of phase separations and chemical changes: None Surface Collecting Agents 244 SILTECH OP-40 ------- V. SHELF LIFE Minimum of three years in unopened container. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spray on water around the perimeter of an oil slick using a pressurized backpack sprayer or aerial applicator. 2. Concentration/Application Rate: 6.4 U.S. gallons/mile (or 15L/km). 3. Conditions for Use: SILTECH OP-40 is designed to aid in situ burning of free oil in calm water with drift ice where fire boom would be ineffective. When sprayed on the water around the perimeter of an oil slick, SILTECH OP-40 will concentrate the oil to a thickness suitable for igniting a burn. It works in all water temperatures and salinities and works best with fluid petroleum that has not weathered significantly. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested SILTECH OP-40 No. 2 Fuel Oil SILTECH OP-40 & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 3.33 6.83 40.50 6.43 9.70 3.27 2.33 8.68 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >180°F 2. Pour Point: -74.2 °F 3. Viscosity: 53 SUS at 100 °F 4. Specific Gravity: 0.98816 at 60°F 5. pH: 8.03 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: None 9. Solubility in Water: Partly miscible Surface Collecting Agents 245 SILTECH OP-40 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) ND ND ND ND ND ND ND ND ND ND Surface Collecting Agents 246 SILTECH OP-40 ------- SURFACE WASHING AGENTS: TECHNICAL NOTEBOOK BULLETINS Surface Washing Agents 247 Surface Washing Agents ------- TECHNICAL PRODUCT BULLETIN #SW-2 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JANUARY 7, 1985 REVISED LISTING DATE: AUGUST 21, 1995 "TOPSALL #30" (aka, SUPERALL #38) I. NAME, BRAND, OR TRADEMARK TOPSALL #30 (AKA, SUPERALL #38) Type of Product: Surface Washing Agent (Oil and Petroleum Cleaning Agent) (formerly #D-20) II. NAME, ADDRESS, AND TELEPHONE TOPSALL #30 Stutton North Corporation P.O. Box 724 Mandeville, LA 70470 Phone: (985) 626-3900 Fax:(985)674-0476 (Mr. David Anton) NUMBER OF MANUFACTURER/CONTACT SUPERALL #38 Superall Products LLP P.O. Box 2954 Spring, TX 77383 Phone: (281)351-4800 Fax: (281) 351-4855 E-mail: info@superall.com Website: www.superall.com (Mr. Sammy Roberts II) III. NAME, ADDRESS, AND TELEPHONE TOPSALL #30 Stutton North Corporation P.O. Box 724 Mandeville, LA 70470 Phone: (985) 626-3900 Fax:(985) 674-0476 (Mr. David Anton) NUMBER OF PRIMARY DISTRIBUTORS SUPERALL #38 Superall Environmental LLC P.O. Box 2954 Spring, TX 77383 Phone: (281)351-4800 Fax: (281) 351-4855 E-mail: info@superall.com Website: www.superall.com (Mr. Sammy Roberts II) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: TOPSALL #30 (aka, SUPERALL #38) is non-flammable. 2. Ventilation: Normal type household ventilation is adequate for handling and storage. 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of contact with eyes, wash thoroughly with large amounts of water. If irritation persists, seek medical attention. Use protective gloves for manual cleaning. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 20°F Surface Washing Agents 248 TOPSALL #30 ------- 4.c. Optimum storage temperature range: 40°F to 100°F 4.d. Temperatures of phase separations and chemical changes: TOPSALL #30 (aka, SUPERALL #38) has a pour point of 20°F and a boiling point of 212°F. V. SHELF LIFE TOPSALL #30 (aka, SUPERALL #38) has a shelf life of not less than two years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: For general use, apply by spray, mop, etc. Agitate severe spots and rinse thoroughly for a residue-free surface. 2. Concentration/Application Rate: Normal cleaning (rigs and platforms, bilges, decks, waterline scum, shop machinery and equipment) use 1 part TOPSALL #30 (aka, SUPERALL #38) to up to 20 parts water. Heavy cleaning (degassing tanks and barges, engine rooms and soot, oil stained concrete, petroleum based drilling muds) use 1 part TOPSALL #30 (aka, SUPERALL #38) to up to 15 parts water. Severe cleaning (Black magic, Bunker C, crude oil, holding tanks, grease traps) use 1 part TOPSALL #30 (aka, SUPERALL #38) to up to 5 parts water. Steam cleaning use 1 part TOPSALL #30 (aka, SUPERALL #38) to up to 50 parts of water. Pressure wash use 1 part TOPSALL #30 (aka, SUPERALL #38) to up to 30 parts water. DO NOT USE UNDILUTED ON COMPOSITION FLOORS, WATER BASED PAINTED SURFACES, OR ALUMINUM. 3. Conditions for Use: Recommended for cleaning petroleum fractions from decks, platforms, bilges, rigs, and other seagoing equipment, as noted above. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) TOPSALL #30 Menidia beryllina 156.60 96-hr (aka, SUPERALL #38) Mysidopsis bahia 115.80 48-hr No. 2 Fuel Oil Menidia beryllina 6.40 96-hr Mysidopsis bahia 1.30 48-hr TOPSALL #30 Menidia beryllina 4.60 96-hr (aka, SUPERALL #38) & Mysidopsis bahia 5.00 48-hr No. 2 Fuel Oil (1:10) Reference Toxicant (DSS) Menidia beryllina 1.60 96-hr Mysidopsis bahia 10.00 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. Surface Washing Agents 249 TOPSALL #30 ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: 20°F 3. Viscosity: 30.53 SUS at 100°F 4. Specific Gravity: 1.06 at 70°F 5. pH: 12.6 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility: Miscible with water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.05 Cadmium <0.002 Chromium 0.031 Copper 0.25 Lead 0.02 Mercury <0.01 Nickel <0.01 Zinc 0.25 Cyanide <0.1 Chlorinated Hydrocarbons <0.1 Surface Washing Agents 250 TOPSALL #30 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 11/03/2008 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-9 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MAY 25, 1989 REVISED LISTING DATE: APRIL 16, 1996 "CN-110" I. NAME, BRAND, OR TRADEMARK CN-110 Type of Product: Surface Washing Agent (formerly D-37) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Chemex, Inc. 107-B Balboa Drive Broussard, LA 70518 Phone: updated information required E-mail: updated information required (Contact: updated information required) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Chemex, Inc. 107-B Balboa Drive Broussard, LA 70518 Phone: updated information required E-mail: updated information required (Contact: updated information required) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: None needed. 3. Skin and eye contact; protective clothing; treatment in case of contact: As in handling any industrial chemical, the standard precautions of wearing chemical-resistant gloves and eye protection are recommended. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: -40°F 4.c. Optimum storage temperature range: 70°F-80°F 4.d. Temperatures of phase separations and chemical changes: Product does not lose effectiveness between temperatures of -40°F through 120°F, although it will become hazy if the temperature is sustained at less than 30°F over a 24-hour period. Surface Washing Agents 251 CN-110 ------- V. SHELF LIFE: CN-110 has a shelf life of 2 years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: There are no application restrictions. The preferred application method is by spraying and/or applying the product over the pollutant (primarily oil of any viscosity) on the stained area. Immediately, the product begins to work on breaking the physical bond between the oil and the object desired to be cleaned. The full effect of CN-110 on hard, porous and most non-porous materials usually takes a minimum of 30 minutes with a maximum retention time of 60 minutes. Then the freed oil is sprayed off with available water. The oil is then safely and effectively skimmed without dispersed oil remaining in the affected waters. If "herding" or "corralling" a slick is desired, CN-110 can also be applied without the increased toxicities by dispersing minute particles of oil into the affected water stream. 2. Concentration/Application Rate: Application concentration for cleaning shorelines is approximately 1 gallon per 75-100 square feet of affected area. Depending on depths of shorelines, this amount will give a residual of much less than 1 ppm of CN-110 in the affected waters. This residual should be lower than the toxicity of the spilled oil. If "herding" is desired, the application concentration should be in its original state while either spraying CN-110 around the slick or dropping small amounts from a plane. The resulting residual concentration in this case should be the same as shoreline cleaning or less. If it is desired that CN-110 be added to a high-pressure cleaning system or steam, the dilution rate should be no lower than 10%. This will lower the CN-110 residual in the affected waters to the parts per billion range. 3. Conditions for Use: Preferably fresh water, at temperature of 32°F. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) CN-110 Menidia beryllina 52,233.00 96-hr Mysidopsis bahia 12,262.00 48-hr No. 2 Fuel Oil Menidia beryllina 1.90 96-hr Mysidopsis bahia 0.90 48-hr CN-110 Menidia beryllina 7.40 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 1.19 48-hr Reference Toxicant (DSS) Menidia beryllina 1.80 96-hr Mysidopsis bahia 5.90 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA Surface Washing Agents 252 CN-110 ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: None 2. Pour Point: 30°F 3. Viscosity: 45.7 cSt at 78°F 4. Specific Gravity: 1.025 5. pH: 11.4 6. Surface Active Agents: Trace amounts of a sulfonated compound 7. Solvents: None 8. Additives: Complex silicate solution 9. Solubility: NA X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons * Duplicate Analyses CYANIDES, AND CHLORINATED Concentration (ppm) <0.22 <0.088 0.109/0.131* 0.238/0.234* <0.275 <0.0001 <0.11 <0.374/<0.369* 0.25 ND Surface Washing Agents 253 CN-110 ------- TECHNICAL PRODUCT BULLETIN #SW-10 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 21, 1989 REVISED LISTING DATE: SEPTEMBER 27, 1995 "COREXIT™ EC9580A" I. NAME, BRAND, OR TRADEMARK COREXIT™ EC9580A Type of Product: Surface Washing Agent (hydrocarbon based) (formerly COREXIT 9580 SHORELINE CLEANER; D-38) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Corexit Environmental Solutions LLC 11177 South Stadium Drive Sugar Land, TX 77478 Product Management: Phone: (281)632-8827 E-mail: corexitinfo@corexit.com (Mr. Huw Jones) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO nonflammable; DOT combustible 2. Ventilation: Use with ventilation equal to unobstructed outdoors in moderate breeze. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with eyes, skin and clothing. Wash skin with soap and water. Flush eyes with plenty of water until irritation subsides. Remove to fresh air. 4.a. Maximum storage temperature: 170°F 4.b. Minimum storage temperature: -30°F 4.c. Optimum storage temperature range: 40°F-100°F 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE The shelf life of unopened drums of COREXIT™ EC9580A is unlimited. Surface Washing Agents 254 OREXIT™ EC9580A ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: COREXIT™ EC9580A contains a balanced formula of specifically selected biodegradable surfactants in a de-aromatized hydrocarbon solvent system. COREXIT™ EC9580A has a very low degree of toxicity to marine and shoreline organisms. Shorelines, Mangroves, and Seagrasses - COREXIT™ EC9580A is sprayed directly on the oiled rocky shorelines, mangroves or seagrasses full strength as supplied. After a soak time of zero to thirty minutes, rinse the cleaner and the oil released from the shoreline surface into the water where it can be readily recovered by conventional means such as skimmers or absorbents. The soak time may vary with temperature, oil density and degree of weathering. 2. Concentration/Application Rate: The recommended dosage is approximately 1 gallon per 100 square feet but this can vary depending on the amount of weathering and oiling. The product should be applied full strength as supplied. Since it is hydrocarbon-based, the product should not be diluted with water during application as this will greatly reduce effectiveness. 3. Conditions for Use: COREXIT™ EC9580A is useful on shorelines in fresh or salt water. It is effective on all types of oil including heavily weathered and emulsified oil ("chocolate mousse") containing up to 50 percent water. VII. TOXICITY AND EFFECTIVENESS ~. Toxicity: Material Tested Species LC50 (ppm) COREXIT™ EC9580A Menidia beryllina 86.88 96-hr Mysidopsis bahia 31.96 48-hr No. 2 Fuel Oil Menidia beryllina 10.72 96-hr Mysidopsis bahia 16.12 48-hr COREXIT™ EC9580A & Menidia beryllina 13.20 96-hr No.2 Fuel Oil (1:10) Mysidopsis bahia 9.06 48-hr Reference Toxicant (DSS) Menidia beryllina 7.02 96-hr Mysidopsis bahia 9.82 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 174°F 2. Pour Point: -65°F 3. Viscosity: 8 cSt at 104°F, 28 cSt at 32°F 4. Specific Gravity: 0.810 at 60°F 5. pH: Not Applicable ~. Surface Active Agents: CONFIDENTIAL Surface Washing Agents 255 OREXIT™ EC9580A ------- 7. Solvents: De-aromatized Hydrocarbon 8. Additives: None 9. Solubility: Not Applicable X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.06 Cadmium <0.002 Chromium 0.003 Copper <0.001 Lead <0.009 Mercury <0.0002 Nickel 0.01 Zinc 0.041 Cyanide <0.05 Chlorinated Hydrocarbons ND Surface Washing Agents 256 OREXIT™ EC9580A ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-11 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JUNE 26, 1989 REMOVAL DATE: SEPTEMBER 15, 1994 RELISTING DATE: JULY 07, 2010 "DE-SOLV-IT INDUSTRIAL FORMULA" I. NAME, BRAND, OR TRADEMARK DE-SOL V-IT INDUSTRIAL FORMULA Type of Product: Surface Washing Agent (formerly D-40) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Orange-Sol Blending and Packaging 1400 N Fiesta Boulevard Gilbert, AZ 85233 Phone: (800) 877-7771 Fax: (480) 497-0444 E-mail: updated information required Website: www.orange-sol.com (Mr. Albert Farnsworth or Mr. Jack Farnsworth at (480) 319-0141) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Bell Tech Master Distributor P.O. Box 2198 Valdez, AK 99686 Phone: (907) 602-0111 Fax: (907) 835-4535 E-mail: bellenterprise@cvinternet.net (Mr. Randy Bell) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Not regulated unless shipped by land in a package having a capacity of 3,500 gallons or more). Combustible Class IIIA per OSHA, 29 CFR 1910.106 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment of clothing required; however, goggles are recommended where splash is potential. If eye or skin 3/03/2016 7/27/2022 Surface Washing Agents 257 PREMIER 99 ------- irritation occurs, flush with ample fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: -20°F 4.c. Optimum storage temperature range: 0°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Two (2) years in sealed polydrums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: DE-SOLV-IT (DSI) is to be used in neat form. DSI works just as well with fresh or salt water. This product works well with all types of oils. Product can be used on oil-contaminated beaches. 2. Concentration/Application Rate: Use DSI directly on the contaminated area, or up to approximately a 1:10 dilution ratio (product:water). Lighter oils will require a 1:10 to 1:30 product to water dilution ratio. Warmer waters (greater than 78°F) and/or good agitation during application will require less product. Response personnel can determine best method to collect clean up residue. Clean up residue should be collected and disposed of in accordance to local, state, and federal regulations. 3. Conditions for Use: Effective in salt or fresh water, with no limitations as to usage within optimum temperature parameters (application may be made at or above 35°F, with optimum above 48°F). VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) DE-SOLV-IT Menidia beryllina 37.71 96-hr Mysidopsis bahia 4.57 48-hr No. 2 Fuel Oil Menidia beryllina 3.76 96-hr Mysidopsis bahia 2.04 48-hr DE-SOLV-IT & Menidia beryllina 9.40 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 1.68 48-hr Reference Toxicant (SLS) Menidia beryllina 12.25 96-hr Mysidopsis bahia 11.71 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 145°F 2. Pour Point: -84°F 3. Viscosity: 1.8 cSt @ 40°C Surface Washing Agents 258 PREMIER 99 ------- 4. Specific Gravity: 1.8345 @60°F 5. pH: 6.6 6. Surface Active Agents: Nonionic PROPRIETARY Surfactants 7. Solvents: PROPRIETARY 8. Additives: None 9. Solubility: Miscible in oil and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.010 Cadmium <0.005 Chromium <0.015 Copper <0.015 Lead <0.010 Mercury <1 |ig/L Nickel <0.025 Zinc 0.0.15 Cyanide <0.010 Chlorinated Hydrocarbons <6.00 Surface Washing Agents 259 PREMIER 99 ------- LISTING CHANGES PENDING; VERIFICATION BY MANUFACTURER AND EPA REQUIRED TECHNICAL PRODUCT BULLETIN #SW-12 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 11, 1989 REVISED LISTING DATE: NOVEMBER 2, 1995 "PREMIER 99" I. NAME, BRAND, OR TRADEMARK PREMIER 99 Type of Product: Surface Washing Agent (Water Based) (formerly D-41) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Gold Coast Chemical Products 2357 Stirling Road Dania Beach, FL 33312 Phone: (954) 893-0044 Fax: (954) 893-8884 E-mail: noslime@goldcoastchemical.com (Mr. Eli Finkelberg or Ms. Maria Morris) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Gold Coast Chemical Products 2357 Stirling Road Dania Beach, FL 33312 Phone: (954) 893-0044 Fax:(954) 893-8884 E-mail: noslime@goldcoastchemical.com (Mr. Eli Finkelberg or Ms. Maria Morris) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: None 2. Ventilation: Adequate ventilation is needed if in closed environment. 3. Skin and eye contact; protective clothing; treatment in case of contact: Skin and eye contact: Detergents will defat skin and eyes. May cause irritation. Protective clothing: Use protective gloves for manual cleaning and splash goggles. Treatment in case of contact: If splashed on skin, wash with copious amounts of water. If ingested, drink diluted vinegar or lemon juice. Get medical attention. 4.a. Maximum storage temperature: 125°F 4.b. Minimum storage temperature: 0°F 4.c. Optimum storage temperature range: 0°F - 75°F Surface Washing Agents 260 PREMIER 99 ------- Avoid freezing the product. If material freezes and separation is experienced, it should be warmed and mixed together. 4.d. Temperatures of phase separations and chemical changes: No separation expected down to 20°F. V. SHELF LIFE Unopened material - at least 5 years is expected. Opened material - at least 2 years is expected. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Apply by spray, mop, or pressure washer, etc. Agitate severe spots. Rinse thoroughly for residue free surface. 2. Concentration/Application Rate: Normal Cleaning - 1 part PREMIER 99 to up to 20 parts water. Heavy Cleaning - 1 part PREMIER 99 to up to 15 parts water. Severe Cleaning - 1 part PREMIER 99 to up to 5 parts water. Steam Cleaning - 1 part PREMIER 99 to up to 50 parts water. Pressure Wash - 1 part PREMIER 99 to up to 30 parts water. 3. Conditions for Use: Water salinity, water temperature, types and ages of pollutants are not determined. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) PREMIER 99 Menidia beryllina 565.70 96-hr Mysidopsis bahia 94.70 48-hr No. 2 Fuel Oil Menidia beryllina 10.20 96-hr Mysidopsis bahia 2.10 48-hr PREMIER 99 & Menidia beryllina 8.20 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.50 48-hr Reference Toxicant (DSS) Menidia beryllina 1.55 96-hr Mysidopsis bahia 7.96 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 160°F Surface Washing Agents 261 PREMIER 99 ------- 2. Pour Point: NA 3. Viscosity: 15 cps 4. Specific Gravity: 1.01 5. pH: 10- 11.5 6. Surface Active Agents: Active 8000* - Purity Chemical <10% 7. Solvents: <5% 8. Additives: <5% 9. Solubility: Complete in Water *NOTE: Particular chemical composition of Active 8000 is considered by Purity Chemical as a trade secret. More detailed information can be given by Purity Chemical - Mr. Jim Palmer, 1800 NW 70th Avenue, Miami, FL 33126, 1-800-654-0235, FAX (305) 592-2601. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic < 0.01 Cadmium < 0.0005 Chromium <0.1 Copper <0.1 Lead < 0.005 Mercury <0.001 Nickel < 0.5 Zinc <0.1 Cyanide < 0.005 Chlorinated Hydrocarbons ND Surface Washing Agents 262 PREMIER 99 ------- LISTING CHANGES PENDING; VERIFICATION BY MANUFACTURER AND EPA REQUIRED TECHNICAL PRODUCT BULLETIN #SW-15 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: APRIL 23,1990 REVISED LISTING DATE: AUGUST 30, 1995 "SIMPLE GREEN®" I. NAME, BRAND, OR TRADEMARK SIMPLE GREEN® Type of Product: Surface Washing Agent (Water Based) (formerly D-46) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Sunshine Makers, Inc. 15922 Pacific Coast Highway Huntington Beach, CA 92649 Phone: (800) 228-0709 Phone: (562) 795-6000 Fax: (562) 592-3830 E-mail: LLorincz@simplegreen.com (Ms. Laura Lorincz) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Sunshine Makers, Inc. 15922 Pacific Coast Highway Huntington Beach, CA 92649 Phone: (800) 228-0709 Phone: (562) 795-6000 Fax: (562) 592-3830 E-mail: LLorincz@simplegreen.com (Ms. Laura Lorincz) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Not required. 3. Skin and eye contact; protective clothing; treatment in case of contact: SIMPLE GREEN® is safe for use on skin and will not cause irritation in the majority of users. Avoid contact with eyes, irritation may result. Wear splash goggles or full face-shield and have eye washing equipment available in areas where potential is high for eye contact. No special precautions or additional protective equipment are required during handling or use. SIMPLE GREEN® is provided with a Material Safety Data Sheet (No. 1002). Surface Washing Agents 263 SIMPLE GREEN® ------- 4.a. Maximum storage temperature: 140°F 4.b. Minimum storage temperature: 34°F 4.c. Optimum storage temperature range: >32°F and <140°F 4.d. Temperatures of phase separations and chemical changes: SIMPLE GREEN® is stable and phase separation will not occur at temperatures within the above storage range. V. SHELF LIFE SIMPLE GREEN® has an unlimited shelf life. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spray on oily surface. 2. Concentration/Application Rate: For open water, spray concentrated product directly on surface of oil at a ratio of 4 parts of oil to 1 part of SIMPLE GREEN®. Site conditions may warrant alternative procedures to maintain effectiveness. 3. Conditions for Use: Equally effective in fresh water, estuarine, and marine environments at all temperatures. SIMPLE GREEN® contains no known EPA Priority Pollutants. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) SIMPLE GREEN® Menidia beryllina 27.90 96-hr Mysidopsis bahia 77.60 48-hr No. 2 Fuel Oil Menidia beryllina 6.50 96-hr Mysidopsis bahia 3.70 48-hr SIMPLE GREEN® & Menidia beryllina 8.30 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 4.40 48-hr Reference Toxicant (DSS) Menidia beryllina 7.80 96-hr Mysidopsis bahia 21.20 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. VIII. MICROBIOLOGICAL ANALYSIS SIMPLE GREEN® contains no microorganisms, enzymes, or biological material. IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: None 3. Viscosity: 2.0 Centistokes at 78°F 4. Specific Gravity: 1.0257 g/ml at 72°F 5. pH: 9.5 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL Surface Washing Agents 264 SIMPLE GREEN® ------- 8. Additives: CONFIDENTIAL 9. Solubility: Infinitely miscible. (Increasing salt concentrations in marine ecosystems will lead to complexes with SIMPLE GREEN® that may become visible at ratios above one part SIMPLE GREEN® to 99 parts seawater.) X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <5.0000 Cadmium <0.0233 Chromium 0.1150 Copper <0.7500 Lead 0.0776 Mercury <0.0125 Nickel <2.3000 Zinc <4.4000 Cyanide <1.0000 Chlorinated Hydrocarbons <1.0 Surface Washing Agents 265 SIMPLE GREEN® ------- TECHNICAL PRODUCT BULLETIN #SW-16 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 8, 1991 REVISED LISTING DATE: JUNE 14, 1995 "AQUACLEAN" I. NAME, BRAND, OR TRADEMARK AQUACLEAN Type of Product: Surface Washing Agent (formerly D-52) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Madison Chemical Company, Inc. 3141 Clifty Drive Madison, IN 47250 Phone: (812) 273-6000 Fax:(812) 273-6002 E-mail: steve.preece@madchem.com (Dr. Steve Preece) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Madison Chemical Company, Inc. 3141 Clifty Drive Madison, IN 47250 Phone: (812) 273-6000 Fax:(812)273-6002 E-mail: steve.preece@madchem.com (Dr. Steve Preece) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Handle in a well-ventilated space. Local exhaust is recommended if TLV's are exceeded. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye and skin contact. In case of such contact, immediately flush with large amount of cool water for at least 15 minutes, and call a physician. Wear protective eye goggles, impermeable protective gloves, and protective clothing when handling the product. Wash contaminated protective equipment (including clothing, shoes, eye goggles, gloves, etc.) thoroughly in soap and water, rinse repeatedly in clean water and dry before reuse. Avoid ingestion, breathing dusts, mists, or fumes. In case of ingestion, induce vomiting, give water and call a physician. In case of inhalation, move the affected person to fresh air, and call a physician. 4.a. Maximum storage temperature: 140°F Surface Washing Agents 266 AQUACLEAN ------- 4.b. Minimum storage temperature: 50°F 4.c. Optimum storage temperature range: >50°F to <104°F 4.d. Temperatures of phase separations and chemical changes: <50°F, >104°F V. SHELF LIFE 18 months if stored between 50°F and 104°F, and away from acids. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: AQUACLEAN may be introduced with a pressure spray to cover the affected area, after the appropriate dilution or concentration is prepared. After application, agitate spill area with water using a solid stream flow. For manual cleaning with AQUACLEAN, follow instructions in the product data sheet provided by the manufacturer. 2. Concentration/Application Rate: For small spills, dilute 3 to 1 with water and apply as above. For large spills, prepare a 33% solution of AQUACLEAN and apply through a foam eductor at 6% setting with approximately 90 gallons per minute flow at the nozzle. For spills on shorelines and beaches, dilute AQUACLEAN 50% with fresh water and apply using a pressure spray to cover the entire contaminated area. Then rinse with fresh water. 3. Conditions for Use: Water temperature should be above 41°F. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material tested Species LC50 (ppm) AQUACLEAN Menidia beryllina 70.7 96-hr Mysidopsis bahia 32.7 48-hr No. 2 Fuel Oil Menidia beryllina 4.4 96-hr Mysidopsis bahia 1.8 48-hr AQUACLEAN and Menidia beryllina 6.5 96-hr No. 2 Fuel (1:10) Mysidopsis bahia 2.1 48-hr Reference Toxicant (DSS) Menidia beryllina 1.4 96-hr Mysidopsis bahia 4.9 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Surface Washing Agents 267 AQUACLEAN ------- IX. PHYSICAL PROPERTIES 1. Flash Point: None detected 2. Pour Point: -20°F 3. Viscosity: 16.5 cP at 25°C (77°F) 4. Specific Gravity: 1.06 at 25°C (77°F) 5. pH: 11.8 (at full strength) 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: Anionic and nonionic synthetic surfactants. 8. Solvents: CONFIDENTIAL 9. Additives: CONFIDENTIAL 10. Solubility: Completely soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 1.10 Cadmium 0.16 Chromium 0.20 Copper 0.66 Lead 1.83 Mercury <0.01 Nickel 0.80 Zinc 0.29 Cyanide 0.06 Chlorinated hydrocarbons 4.20 Surface Washing Agents 268 AQUACLEAN ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 6/10/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-18 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: OCTOBER 23, 1996 "NATURE'S WAY HS" (There is only one listing and no "aka 's "for this product.) I. NAME, BRAND, OR TRADEMARK NATURE'S WAY HS Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Integra Environmental, Ltd. 5825 Central crest Houston, TX 77092 Phone: updated information required Fax: updated information required Email: updated information required Website: updated information required (Ms. Cathy Kaiser) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Integra Environmental, Ltd. 5825 Central crest Houston, TX 77092 Phone: updated information required Fax: updated information required Email: updated information required Website: updated information required (Ms. Cathy Kaiser) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: No special precautions are required, but in case of inhalation, move person to fresh air. 3. Skin and eye contact; protective clothing; treatment in case of contact: Flush contaminated skin with plenty of water for at least 15 minutes. Consult a physician if irritation develops. Protective gloves are recommended for extended or prolonged contact, (e.g., immersing hands). Tight fitting safety goggles are recommended for handling product in concentrated form, especially if contacts are worn. 4.a. Maximum storage temperature: 130°F Surface Washing Agents 269 NATURE'S WAY HS ------- 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature: 90°F 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE NATURE'S WAY HS has a five year shelf life. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: NATURE'S WAY HS may be applied by spraying, pouring, dispensing equipment, or by manual or automatic scrubber machines. Do not mix the product with any other cleaner nor allow any other cleaners to contact surfaces where HS is being used. Hot water should never be used. 2. Concentration/Application Rate: Apply NATURE'S WAY HS full strength (undiluted) to surface area with sprayer, concentrating on areas with heaviest contamination first. To speed clean-up of shorelines and beaches, pressure spray into cracks and crevices prior to scrubbing. Agitate and scrub well using power brushes, hand brushes, brooms or mops. If possible, allow the scrubbed solution to remain on the surface for at least 15 minutes. If allowed to soak overnight, the next morning the treated surface must be re-wet with water, reagitated, and rinsed. Additional product will not be necessary at that time. 3. Conditions for Use: For heavily contaminated surfaces, NATURE'S WAY HS should always be used full strength. For moderate accumulations HS may be diluted to as little as 2 oz. per gallon of cool water for cleaning light contamination. For average contamination, a dilution of 12 oz. per gallon is recommended (1 part NATURE'S WAY HS to 10 parts water). For light use, 4 to 6 oz. of product per gallon water will be sufficient. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (DDm) NATURE'S WAY HS Menidia beryllina 152.14 96-hr Mysidopsis bahia 193.00 48-hr No. 2 Fuel Oil Menidia beryllina 3.15 96-hr Mysidopsis bahia 0.96 48-hr NATURE'S WAY HS Menidia beryllina 3.91 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 1.07 48-hr Reference Toxicant (DSS) Menidia beryllina 96-hr Mysidopsis bahia 5.71 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. a. Effectiveness: NA Surface Washing Agents 270 NATURE'S WAY HS ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: NA 2. Pour Point: Flowable at all temperatures above freezing 3. Viscosity: <100 CPS 4. Specific Gravity: 1.01 5. pH: 8-9.5 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: NA X. ANALYSIS FOR HEAVY METALS AND CHLORINATED HYDROCARBONS ComDOund Concentration (dditi) Arsenic <0.003 Cadmium <0.005 Chromium <0.010 Copper 0.020 Lead <0.002 Mercury <0.0002 Nickel <0.030 Zinc 0.260 Cyanide <0.020 Chlorinated Hydrocarbons ND Surface Washing Agents 271 NATURE'S WAY HS ------- TECHNICAL PRODUCT BULLETIN #SW-19 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JANUARY 30, 1997 "CYTOSOL" I. NAME, BRAND, OR TRADEMARK CYTOSOL Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT CytoCulture International, Inc. 122 Martina Street Point Richmond, CA 94801-3829 Phone: (510) 233-0102 Fax: (510) 233-3777 Emergency Mobile: (510) 233-0102 E-mail First Response: rvwedel@gmail.com E-mail: cytoculture@gmail.com Website: www.cvtosolbiosolvent.com Website: www.cvtoculture.com (Dr. Randall von Wedel) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS CytoCulture International, Inc. Foss Environmental, Inc. 122 Martina Street 7440 West Marginal Point Richmond, CA 94801-3829 Seattle, WA 98108-4141 Phone: (510) 233-0102 Phone: (206) 768-1450 Fax: (510) 233-3777 Fax: (206) 767-3460 Emergency Mobile: (510) 233-0102 (Mr. Larry Pintler) E-mail First Response: rvwedel@gmail.com E-mail: cvtoculture@ gm ail. com Website: www.cvtosolbiosolvent.com Website: www.cvtoculture.com (Dr. Randall von Wedel) Advanced Cleanup Technologies, Inc. 20928 Lamberton Avenue Carson, CA 90810 Phone: (800) 334-2284 Fax: (310) 763-9076 (Mr. Walt Dorn) Surface Washing Agents 272 CYTOSOL ------- IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. However, keep the product away from heat and avoid contact with strong oxidizing agents. Ensure proper disposal of product-saturated absorbents, rags, and combustible materials to avoid the possibility of spontaneous combustion. 2. Ventilation: Product is not volatile. However, in the event of aerosol inhalation, immediately move victim to fresh air. If victim has stopped breathing, give artificial respiration, preferably by mouth to mouth. Get medical attention immediately. 3. Skin and eye contact; protective clothing; treatment in case of contact: The CYTOSOL contains no volatile hydrocarbons or petroleum constituents. However, as a precautionary measure, wear gloves and safety glasses meeting the specifications of ANSI Standard Z87.1. Avoid breathing aerosols. Avoid prolonged contact with skin. 4.a. Maximum storage temperature: 110°F 4.b. Minimum storage temperature: 39°F 4.c. Optimum storage temperature: 55°F 4.d. Temperatures of phase separations and chemical changes: Avoid freezing. At temperatures below the cloud point (43°F), the product may become cloudy, but will return to normal upon warming, with no effect on performance. Store product in airtight containers, if possible, without excessive exposure to moisture. V. SHELF LIFE Closed container: 10 years in a dry environment. Open container: 1 year in a warm, humid environment. The product does not deteriorate appreciably over time, but will grow bacteria if water condensation accumulates in the container. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: The CYTOSOL is applied to oiled shorelines to extract and recover weathered petroleum by flotation with passive water deluges from header pipes or manual spraying. Remaining residual hydrocarbons are biodegraded, either passively by intrinsic bioremediation, or aggressively by enhancing the process with controlled amounts of nutrients and/or acclimated cultures of bacteria cultured from the site, when approved by local, state and federal agencies. The CYTOSOL process is most suitable for the treatment of heavily oiled shorelines that do not respond well to conventional treatments, or that are considered too sensitive for mechanical/pressure wash strategies. Prior to the application of CYTOSOL, collection booms, oil skimmers, sorbent pads, or other appropriate containment and collection mechanisms must be deployed and operational. 2. Concentration/Application Rate: CYTOSOL may be applied with a variety of spraying or washing equipment, depending upon the scale and type of shoreline to be cleaned. The product is to be used only neat and undiluted, for direct application to spilled oil. For large beach areas, CYTOSOL can be sprayed from water trucks or work boats equipped with pumps, hoses, and Surface Washing Agents 273 CYTOSOL ------- nozzles to deliver the product as an aerial spray. In smaller applications, CYTOSOL may be applied with hand sprayers or portable pumps to spray the product directly onto oiled surfaces. Dose rates will vary with the type and amount of petroleum spilled, the extent of weathering, and other site specific conditions, including temperature, porosity of shoreline, and residence time available to let the product contact the oil. In general, the ratio of applied CYTOSOL to crude oil is between 0.5:1 and 1:1. The quantity of CYTOSOL applied should be approximately equivalent to the quantity of petroleum accumulated on the shoreline, or as required to dissolve and remove weathered oil. After application, the product should be allowed to penetrate and dissolve the weathered petroleum for at least one hour, preferably longer. Cold weather applications will require more contact time before initiating recovery. In tidal areas, it is advisable to apply the CYTOSOL as the tide is ebbing (receding) to maximize contact time. Trapped oil may continue to be released for several days, requiring that containment devices be left in place. 3. Conditions for Use: The following shoreline types are appropriate for the use of CYTOSOL: Coarse sand beaches where petroleum has penetrated into sand; marsh areas and vegetated wetlands where oil has coated plants and become trapped; concrete bulkheads, rip rap and piers that may have trapped oil; oiled pilings; gravel or cobble shorelines and rocky shores, where oil has become trapped in pockets; and, public beaches, fisheries, hatcheries, river banks, and other sensitive or high impact sites. The CYTOSOL has been fielded tested successfully for removing oil from mussel beds and intertidal zones, pilings and concrete rip rap. The CYTOSOL also proved effective in facilitating the removal of oil from the banks and vegetation along an oiled creek. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (DDm) CYTOSOL Menidia beryllina 738.0 96-hr Mysidopsis bahia 124.0 48-hr No. 2 Fuel Oil Menidia beryllina 38.9 96-hr Mysidopsis bahia 5.9 48-hr CYTOSOL & Menidia beryllina 24.3 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 7.0 48-hr Reference Toxicant (DSS) Menidia beryllina 13.8 96-hr Mysidopsis bahia 22.2 48-hr NOTE: This toxicity data was derived with the EPA protocols for dispersants using a blender to emulsify the product into the water for testing organisms. The CYTOSOL emulsion created microdroplets of product which may have had direct physical effects on the test larvae. Since the solubility of the product in water is so low (14 ppm or less), it is probable that the observed effects on the test organisms was caused by larvae having direct contact with droplets of product rather than by a true chemical toxicity from the trace amount of dissolved product. In practice, the CYTOSOL would not be emulsified to any great extent during application. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. Surface Washing Agents 274 CYTOSOL ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 360°F 2. Pour Point: 10°F 3. Viscosity: 4.15 CST @ 104°F 4. Specific Gravity: 0.8877 @ 60°F 5. pH: Neutral 6. Surface Active Agents: None 7. Solvents: No Petroleum Distillates 8. Additives: CONFIDENTIAL 9. Solubility: 14 ppm in fresh water, 7 ppm in sea water X. ANALYSIS FOR HEAVY METALS AND CHLORINATED HYDROCARBONS Compound Concentration Arsenic ND Cadmium ND Chromium ND Copper ND Lead ND Mercury ND Nickel ND Zinc ND Cyanide ND Chlorinated Hydrocarbons ND Surface Washing Agents 275 CYTOSOL ------- TECHNICAL PRODUCT BULLETIN #SW-20 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 21, 1997 "BIOSOLVE® PINKWATER®" I. NAME, BRAND, OR TRADEMARK BIOSOLVE® PINKWATER® Type of Product: Surface Washing Agent (formerly BIOSOLVE® HYDROCARBON MITIGATION™ AGENT) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT The BioSolve® Company 24 Victory Lane Dracut, MA 01826 Phone: (781) 482-7900 or (800) 225-3909 Fax: (781)482-7909 Website: www.biosolve.com E-mail: info@biosolve.com (Mr. Stephen Hosmer) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS The BioSolve® Company 24 Victory Lane Dracut, MA 01826 Phone: (781) 482-7900 or (800) 225-3909 Fax: (781)482-7909 Website: www.biosolve.com E-mail: info@biosolve.com (Mr. Stephen Hosmer) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal 3.Skin and eye contact; protective clothing; treatment in case of contact: Flush contaminated eyes thoroughly with water for 15 minutes, and get medical attention. Remove contaminated clothing, wash exposed area with soap and water, wash clothing before reuse. Get medical attention if irritation develops. Get medical attention for ingestion. No medical attention is necessary with inhalation. There are no special storage requirements or special handling precautions; use good normal hygiene. 4.a. Maximum storage temperature: 120°F (50°C) 4.b. Minimum storage temperature: 35°F (1.5°C) 4.c. Optimum storage temperature: 60°F (15°C) Surface Washing Agents 276 BIOSOLVE® PINKWATER® ------- 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE BIOSOLVE® has a 10+ year shelf life if unopened. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Dilute or use eductors to specified rate and apply through fire hose, power washers, steam powered units, or chemical boom sprayers with nozzles that produce a shearing action. Special nozzles to apply the solution as droplets are not necessary. For shoreline cleanup involving heavy or weathered crude, presoak to a 6% solution may be necessary. 2. Concentration/Application Rate: BIOSOLVE® is a highly concentrated product and must be diluted with water before use. Dilution ratios vary depending on site specific conditions. Dilution ratio's normally run at 6%, 3%, or 1%. For heavy, mousse, or weathered oil, a 3% to 6% solution should be applied. For light or refined products, apply at 2% to 3%. For sheens, apply at .5 to 1%. Since testing shows that BIOSOLVE® quickly emulsifies weathered crude, it is not critical to apply immediately after a spill occurs; impact considerations can be fully considered prior to action taken. Surface Washing Applications: BIOSOLVE® applied through power washers in light dilution is very effective in attaining the removal of oils from rock, cobblestone, shorelines, and sea walls. In marsh or wetland applications, BIOSOLVE® prevents the oil from clinging to grasses and mangroves. Rigs and Platforms: BIOSOLVE® is used to inert undersea pipelines before plugging and abandonment, degas tanks and platforms during work over operations, and to wash drill cuttings to remove oils and prevent sheens on surface waters. 3. Conditions for Use: May be used with salt or fresh water. Temperature is not relevant. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) BIOSOLVE® Menidia beryllina 6.4 96-hr Mysidopsis bahia 3.6 48-hr No. 2 Fuel Oil Menidia beryllina 5.6 96-hr Mysidopsis bahia 2.7 48-hr BIOSOLVE® & Menidia beryllina 7.4 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 1.3 48-hr Reference Toxicant (SDS) Menidia beryllina 7.2 96-hr Mysidopsis bahia 13.4 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and Surface Washing Agents 277 BIOSOLVE® PINKWATER® ------- application rates for field use. b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES (Liquid concentrate) 1. Flash Point: NA, Water based >200°F (93.3°C) 2. Pour Point: 32.9°F (0.5°C) 3. Viscosity: 77.5 Centistrokes (concentrate), 490 centipoise (concentrate), 15 centipoise at 6%, at 60.08°F or 15.6°C 4. Specific Gravity: 1.025 at 60°F or 15.5°C 5. pH: 9.37 +/- 0.5 6. Chemical Name and Percentage by Weight of the Total Formulation: CONFIDENTIAL 7. Surface Active Agents: CONFIDENTIAL 8. Solvents: CONFIDENTIAL 9. Additives: CONFIDENTIAL 10. Solubility: Complete-true solution formed with water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.2 Cadmium <0.18 Chromium <0.5 Copper <0.6 Lead <0.2 Mercury <0.07 Nickel <0.6 Silver <0.4 Zinc 0.51 Cyanide <0.01 Chlorinated Hydrocarbons <0.5 Surface Washing Agents 278 BIO SOLVE® PINKWATER® ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-21 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: MARCH 2, 1998 "PETROTECH 25" I. NAME, BRAND, OR TRADEMARK PETROTECH 25 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Petrotech America Corporation 130 William Street, Suite 802 New York, NY 10038 Phone: (212)933-9071, ext. 7001 Fax: (877) 226-4028 E-mail: Info@helpenvironmental.com (Mr. Lawrence Gallo) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Petrotech America Corporation Manufacturing Plant: 130 William Street, Suite 802 Clariant Corp. New York, NY 1003 8 Charlotte, NC Phone: (212)933-9071, ext. 7001 Fax: (877) 226-4028 E-mail: Info@helpenvironmental.com (Mr. Lawrence Gallo) H.E.L.P. Environmental 926 3rd Avenue Brooklyn, NY 11232 IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION I. Flammability: Non-flammable. 2. Ventilation: Normal. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special handling is required beyond that prescribed under the general OSHA rules for non-hazardous, non- flammable and noncorrosive liquids. This is not to suggest that contact with eyes and skin is totally without risk for allergy. Contact with eyes and skin is to be avoided, as suggested under OSHA procedures. 4.a. Maximum storage temperature: +45°C 7/19/2021 7/27/2022 Surface Washing Agents 279 PETROTECH 25 ------- 4.b. Minimum storage temperature: -5°C (can be stored below its freezing point without detectable loss of performance provided that it is warmed to within liquid range prior to application.) 4.c. Optimum storage temperature: >-5°C and <+45°C 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE PETROTECH 25 has an unlimited shelf-life when maintained in the factory sealed containers and stored within the prescribed temperature limits. Climatic factors such as humidity have no effect on closed container storage although the product is hygroscopic and will absorb water if left for long periods in open containers. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: It is recommended that the surface washing agent PETROTECH 25 be applied to contaminated surfaces in one of three ways: (a) a mixture of ten parts PETROTECH 25 to ninety parts water, either fresh or saltwater, should be discharged over the surface by commercial pressure washer, hot or cold; (b) the same mixture discharged on the surface using standard firefighting apparatus preferably at a nozzle pressure of 100 PSI plus; or (3) PETROTECH 25 in concentrated form can be applied to the surface and manually or mechanically brushed and then water applied. 2. Concentration/Application Rate: Generally, PETROTECH 25 is applied neat in its factory supplied concentrate form. However, for lighter oils where educting or proportioning equipment is available, an aqueous solution of PETROTECH 25 between 3 and 10 percent may be used. Broadly speaking, PETROTECH 25 has no solvent action. For any given oil spill of a specific nature, the application rate is unaffected by neat or diluted application as long as the concentrate to oil ratio remains the same. Applications of diluted PETROTECH 25 in the 6 - 10 percent range via firefighting equipment can be used on automobile and aviation gasoline's together with the lighter oils such as diesel and all jet fuels. The dosage of PETROTECH 25 to be used depends upon two factors: 1) The nature of the oil, and 2) The energy used in its application to the contaminated substrate. 3. Conditions for Use: May be used with salt or fresh water. Temperature is not relevant. Surface Washing Agents 280 PETROTECH 25 ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) PETROTECH 25 Menidia beryllina 601.0 96-hr Mysidopsis bahia 350.0 48-hr No. 2 Fuel Oil Menidia beryllina 2.8 96-hr Mysidopsis bahia 1.8 48-hr PETROTECH 25 & No. 2 Fuel Oil Menidia beryllina 3.4 96-hr (1:10) Mysidopsis bahia 1.0 48-hr Reference Toxicant (DSS) Menidia beryllina 7.9 96-hr Mysidopsis bahia 19.8 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES (Liquid concentrate) 1. Flash Point: None 2. Pour Point: 0°C 3. Viscosity: 700 CP 4. Specific Gravity: 1.03 5. pH: 7.5 6. Chemical Name and Percentage by Weight of Total Formulation: CONFIDENTIAL 7. Surface Active Agents: CONFIDENTIAL 8. Solvents: CONFIDENTIAL 9. Additives: CONFIDENTIAL 10. Solubility: 100% X. ANALYSIS FOR HEAVY METALS AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.10 Cadmium <0.08 Chromium <0.10 Copper <0.26 Lead 0.047 Mercury <0.0005 Nickel <0.40 Zinc 0.256 Cyanide 0.70 Chlorinated Hydrocarbons ND Surface Washing Agents 281 PETROTECH 25 ------- TECHNICAL PRODUCT BULLETIN #SW-23 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: MARCH 1, 1999 "PETRO-CLEAN" I. NAME, BRAND, OR TRADEMARK PETRO-CLEAN Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT B.R.A.T. Microbial Products Inc. 208 Cinnabar Bay Court League City, TX 77573 Phone: (713) 724-9226 E-mail: alabastercorp@gmail.com (Mr. John Sheffield) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS B.R.A.T. Microbial Products Inc. 208 Cinnabar Bay Court League City, TX 77573 Phone: (713) 724-9226 E-mail: alabastercorp@gmail.com (Mr. John Sheffield) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal 3. Skin and eye contact: Protective clothing; treatment in case of contact. Eyes-flush with water using eye cup of fountain for 15 minutes. Seek medical attention if irritation persists. Wash contaminated clothing and footwear before reuse. Ingestion - seek medical attention. Inhalation - no medical attention is required. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE Indefinite when stored properly. Surface Washing Agents 282 PETRO-CLEAN ------- VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: PETRO-CLEAN is applied through power washers or even garden type sprayers in light dilution is very effective in removing petrochemical hydrocarbons from rocks, shorelines, sea walls, bridges, and highways. In wetland applications, PETRO-CLEAN prevents hydrocarbons from attaching to grasses, trees, rocks, etc. 2. Concentration/Application Rate: Dilute or use eductors to specified rate and apply through fire hose, power washers, or sprayers to contaminated area. PETRO-CLEAN is a highly concentrated product and must be diluted before use. Dilution ratios vary depending on the specific conditions of the contaminated site. Normal recommended dilutions are from 0.5% to 6%. On heavy or weathered crude, pre-soaking with 6% may be necessary. For light or refined products, apply as 3% to 6% solution. For sheens on water apply a 0.5% to 1.0% solution. 3. Conditions for Use: May be used with salt or fresh water VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested PETRO-CLEAN No. 2 Fuel Oil PETRO-CLEAN & No. 2 Fuel Oil (1:10) Reference Toxicant (DSS) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: > 200°F 2. Pour Point: -17°F 3. Viscosity: 1.26@75°F 4. Specific Gravity: 0.99 @ 75°F 5. pH: 8.05 (10% solution, s.u.) 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility in Water: 100 percent Species LC50 (ppm) Menidia beryllina 100 96-hr Mysidopsis bahia 110 48-hr Menidia beryllina 110 96-hr Mysidopsis bahia 110 48-hr Menidia beryllina 115 96-hr Mysidopsis bahia 105 48-hr Menidia beryllina 1.14 96-hr Mysidopsis bahia 0.98 48-hr Surface Washing Agents 283 PETRO-CLEAN ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) <0.10 <0.10 <0.01 <0.01 <0.002 <0.01 <0.01 <0.01 <2.0 <1.0 Surface Washing Agents 284 PETRO-CLEAN ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 8/17/2012 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-24 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JULY 14, 2000 "DO-ALL #18" I. NAME, BRAND, OR TRADEMARK DO-ALL #18 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Radcob Solutions, Inc. 4800 North State Road 7, Suite #105 Lauderdale Lakes, FL 33319 Phone: (954) 249-2178 Fax: (954) 640-7080 Email: updated information required Website: updated information required (Mr. Adam Goldberg) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Radcob Solutions, Inc. 4800 North State Road 7, Suite #105 Lauderdale Lakes, FL 33319 Phone: (954) 249-2178 Fax: (954) 640-7080 Email: updated information required Website: updated information required (Mr. Adam Goldberg) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: DO-ALL #18 is water based, contains no solvents and is non-flammable. 2. Ventilation: Normal room ventilation. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with skin, eyes, and clothing. Wear safety glasses or goggles and protective gloves when handling. In case of eye contact, flush immediately with water for at least 15 minutes. If persistent irritation occurs, call a physician. For skin contact, wash thoroughly with soap and water. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 100°F Surface Washing Agents 285 DO-ALL# 18 ------- 4.d. Temperatures of phase separations and chemical changes: DO-ALL #18 has a pour point of 32°F and phase separation occurs at 105°F. V. SHELF LIFE DO-ALL #18 has a shelf life of at least two (2) years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: May be diluted with fresh or salt water. For general use, apply by spray, mop, etc. Agitate severe spots, rinse thoroughly for residue-free surface. 2. Concentration/Application Rate: To clean oil from beaches, rocks, and piers as a shore-line cleaner, first use a pre-treatment or soaking, using one (1) part DO-ALL #18 diluted with three (3) parts of water. Allow 30 to 45 minutes to soften viscous oil deposits (soak time may vary with temperature, oil density, and degree of weathering). After the soaking period, dilute one (1) part of DO-ALL #18 with 15 parts of water and apply with a high pressure water hose (50 - 100 PSI). Oil released can then be removed by vacuuming, skimmers, or absorbents. For normal cleaning of shop machinery, bilges, decks, waterline scum, rigs, and platforms, dilute one (1) part DO-ALL #18 with up to 20 parts of water. For heavy cleaning and degreasing of tanks, barges, engine rooms and soot, oil stained concrete, and petroleum based drilling muds, dilute one (1) part DO-ALL #18 with up to 15 parts of water. For severe cleaning of holding tanks, grease traps, black magic, crude oil, and Bunker C, dilute one (1) part DO-ALL #18 with up to five (5) parts of water. For steam cleaning, dilute one (1) part of DO-ALL #18 with up to 50 parts of water. For pressure washing, dilute one (1) part DO-ALL #18 with up to 30 parts of water. DO NOT USE UNDILUTED ON COMPOSITION FLOORS, WATER-BASED PAINTED SURFACES, OR ALUMINUM, 3. Conditions for Use: Recommended for cleaning petroleum fractions from beaches, rocks, piers, bilges, decks, waterline scum, rigs, platforms, tanks, barges, engine rooms, machinery, holding tanks, and grease traps. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested DO-ALL #18 Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 66.10 96-hr 288.00 48-hr No. 2 Fuel Oil 9.10 96-hr 0.65 48-hr 9.38 96-hr 0.57 48-hr 6.36 96-hr 16.53 48-hr DO-ALL #18 & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Surface Washing Agents 286 DO-ALL# 18 ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: 32°F 3. Viscosity: 1.8 @ 68°F 4. Specific Gravity: 1.07 @ 68°F 5. pH:13.1 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility in Water: Soluble with water. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND (<0.02) Cadmium ND (<0.02) Chromium ND (<0.02) Copper 0.33 Lead ND (<0.02) Mercury ND (<0.00) Nickel ND (<0.10) Zinc 0.28 Cyanide 0.26 Chlorinated Hydrocarbons ND (<0.30) Surface Washing Agents 287 DO-ALL# 18 ------- TECHNICAL PRODUCT BULLETIN #SW-25 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JULY 9, 2001 "SC-1000®" I. NAME, BRAND, OR TRADEMARK SC-1000® Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT GEMTEK® Products 4640 East Elwood Street Phoenix, AZ 85040 Emergency Number: (602) 265-8586 Phone: (800)331-7022 Fax:(602)265-7241 E-mail: sarahkristoff@gemtek.com (Ms. Sarah S. Kristoff) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS GEMTEK® Products 4640 East Elwood Street Phoenix, AZ 85040 Emergency Number: (602) 265-8586 Phone: (800)331-7022 Fax:(602)265-7241 E-mail: sarahkristoff@gemtek.com (Ms. Sarah S. Kristoff) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: General room ventilation is satisfactory. 3.Skin and eye contact; protective clothing; treatment in case of contact: Non-irritating, no first aid needed. May be an eye irritant. Do not spray into eyes; safety glasses are recommended. If irritation does occur, rinse thoroughly with water. 4.a. Maximum storage temperature: None. 4.b. Minimum storage temperature: Room temperature. 4.c. Optimum storage temperature range: 70°F to 90°F 4.d. Temperatures of phase separations and chemical changes: Low temperature can cause handling problems; viscosity of material will increase. The product is an organic compound and it will not typically stratify. The cloud point is 54°F. At 212°F it will boil and at somewhat less (around 130°F) water vapor will form. Repeat freeze/thaw/boiling cycles over a 30-day period Surface Washing Agents 288 SC-1000™ ------- has not demonstrated noticeable break down of the product. V. SHELF LIFE Minimum of 5 years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: SC-1000® is a highly concentrated cleaning compound capable of a multitude of cleaning applications with dilutions ranging from full strength to far in excess of 1:350. Depending on the specific factors in the cleaning environment, the desired cleaning speed with the least amount of SC-1000® can be determined. When diluting, it is recommended that SC-1000® be added to premeasured water to minimize foaming in the solution. 2. Concentration/Application Rate: Beach Waterfront, Rocky Soils, Break Water Structures, and Pier Facilities: For beach sands or light rocky soils, burning or creating a temporary shallow wash tank is most successful. Fill one-half of the tank with contaminated beach sand, then add a solution of SC-1000® and clean water (ocean or fresh) to cover the sand. Gentle agitation will release the oil to the surface of the tank where it can be collected. For rocky surfaces spray with a 20 percent solution of SC-1000® using a horizontal eductor sprayer, spraying side-to-side, allowing the soil to dwell for several minutes before spraying top-to-bottom with clean ocean or fresh water to rinse oil into perimeter oil booms, blankets or impermeable sheeting. Washing Marine Vegetation - Use a non-pressure/impact spraying equipment to dispense a 0.01 percent SC-1000® solution and allow to stand for 5-10 minutes before a final rinsing with fresh or ocean water. Washing Marine Equipment - For wet oils and bunker crude, use SC-1000™ at 20 percent solution (preferably warmer than 80°F) and spray or wipe. Apply directly to equipment, allow to dwell for 1-2 minutes and then spray rinse with fresh or ocean water. For hardened oils, fuels, and viscous lubricants, apply SC-1000® blended with SC-Supersolve™ (a non-toxic, low aromatic, water miscible solvent) at the ratio of 80/20 then dilute with water to a 50 percent solution, spray or wipe onto surface, let stand for 1-2 minutes before rinsing. Heavy Cleaning Examples - Dilution full strength 1:5; diesel engines, auto parts, baked on oil or lube grease, dried oil/enamel, latex paints, thick food syrups, insect smears, dried animal or vegetable fats, hard resins, thick dust-laden oily dirt, asphalt and grass or plant stains. Average Cleaning Examples - Dilution 1:5 up to 1:20; automotive work counters and tools, food and beverage processing equipment, oily or food-laden floors, manufacturing work areas, vehicle maintenance, shipping containers, utility equipment, and parts washers. General Maintenance Examples - 1:20 up to 1:100; vehicle washing, general janitorial for offices/schools/hospitals/recreation and related equipment, pressure sprayers, food preparation and storage, painted/plastic laminate surfaces, sports equipment, general cleaning, immersion tanks, and ultrasonics. 3. Conditions for Use: SC-1000® may be used on any surface that is compatible with water. The product may tarnish some soft aluminum surfaces if not adequately diluted and rinsed with water. Surface Washing Agents 289 SC-1000™ ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (ppm) SC-1000® Menidia beryllina 26.40 96-hr Mysidopsis bahia 15.20 48-hr No. 2 Fuel Oil Menidia beryllina 8.85 96-hr Mysidopsis bahia 1.57 48-hr SC-1000® & No. 2 Fuel Oil Menidia beryllina 4.72 96-hr Mysidopsis bahia 2.13 48-hr Reference Toxicant (SDS) Menidia beryllina 2.22 96-hr Mysidopsis bahia 10.5 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: 25°F 3. Viscosity: <10 cps @ 25°C 4. Specific Gravity: 1.009 5. pH: 10.2 - 10.5 6. Surface Active Agents: CONFIDENTIAL. 7. Solvents: None. 8. Additives: CONFIDENTIAL. 9. Solubility in Water: Soluble in water. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 1.33 Cadmium ND Chromium ND Copper 0.100 Lead ND Mercury ND Nickel ND Zinc 0.20 Cyanide ND Chlorinated Hydrocarbons ND Surface Washing Agents 290 SC-1000™ ------- TECHNICAL PRODUCT BULLETIN #SW-26 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: AUGUST 06, 2001 "GOLD CREW SW" I. NAME, BRAND, OR TRADEMARK GOLD CREW SW Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Gold Crew Products & Services, LLC P.O. Box 12032 Orange, CA 92869 Phone: (714)288-8781 Mobile: (714)318-5997 E-mail: ifigueira@goldcrew.net E-mail: ifigueira@ecschem.com (Mr. Jim Figueira) ECS 5713 Wollochet Drive NW, Suite B Gig Harbor, WA 98332 Phone: (253) 263-8040 E-mail: egrubbs@ecschem.com Website: www.ecschem.com (Mr. Ed Grubbs) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Gold Crew Products & Services, LLC P.O. Box 12032 Orange, CA 92869 Phone: (714)288-8781 Mobile: (714)318-5997 E-mail: i fi gueira@ gol dcrew. net E-mail: ifigueira@ecschem.com (Mr. Jim Figueira) ECS 5713 Wollochet Drive NW, Suite B Gig Harbor, WA 98332 Phone: (253) 263-8040 E-mail: egrubbs@ecschem.com Website: www.ecschem.com (Mr. Ed Grubbs) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Normal. 3. Skin and eye contact; protective clothing; treatment in case of contact: Extensive testing indicates that GOLD CREW SW is non-hazardous and non-toxic to humans; however, good hygiene practices should always be followed as outlined below: Eyes- flush with water; get medical attention if required; Skin - remove contaminated clothing, wash exposed area, and wash clothing before use. If irritation develops get medical attention; Ingestion - get medical attention if required; Inhalation - none considered necessary. 4.a. Maximum storage temperature: When above 120°F, keep container closed and stored in a cool dark place. Evaporation may change product's characteristics. 4.b. Minimum storage temperature: Product will freeze below 25°F. No phase separation will occur. If frozen, thaw, and stir well. Surface Washing Agents 291 GOLD CREW SW ------- 4.c. Optimum storage temperature range: 25°F to 120°F 4.d. Temperatures of phase separations and chemical changes: No separation at any temperature between 32-120°F. No tendency to "layer out" or separate, standing for 30 days. No separation of layering after freezing. V. SHELF LIFE 20 years (unopened). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Apply through hand pump sprayer and allow to soak. 2. Concentration/Application Rate: As a presoak dilute 20 parts water to 1 part SW. For crude oil, allow about 1 hour. For medium distillates, allow 30 minutes. For light distillates, allow 15 minutes. Time may vary depending on weather conditions. After allowing the solution to presoak, wash the area in the following manner: Apply through a power washer or through a steam powered unit at 1 percent, 3 percent, or 5 percent depending on oil viscosity and temperature. 3. Conditions for Use: Equally effective with salt or fresh water. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested GOLD CREW SW No. 2 Fuel Oil GOLD CREW SW & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200 2. Pour Point: 25°F 3. Viscosity: 33.87 CST 4. Specific Gravity: 1.035 5. pH: 9.76 +/- 0.01 6. Surface Active Agents: CONFIDENTIAL. 7. Solvents: None. Species LC50 ism.) Menidia beryllina 13.80 96-hr Mysidopsis bahia 20.40 48-hr Menidia beryllina 6.75 96-hr Mysidopsis bahia 2.82 48-hr Menidia beryllina 6.34 96-hr Mysidopsis bahia 2.70 48-hr Menidia beryllina 2.22 96-hr Mysidopsis bahia 9.52 48-hr Surface Washing Agents 292 GOLD CREW SW ------- 8. Additives: CONFIDENTIAL. 9. Solubility in Water: Complete. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <1.0 Cadmium <0.10 Chromium <1.0 Copper <1.0 Lead <0.5 Mercury <0.02 Nickel <1.0 Zinc 0.44 Cyanide ND Chlorinated Hydrocarbons ND Surface Washing Agents 293 GOLD CREW SW ------- TECHNICAL PRODUCT BULLETIN #SW-28 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 05, 2001 "NALE-IT" I. NAME, BRAND, OR TRADEMARK NALE-IT Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT SPL Control LLC P.O. Box 627 Elmore City, OK 73433 Phone: (580) 788-2187 E-mail: splcontrol@aol.com (Mr. Tom Luster) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS SPL Control LLC P.O. Box 627 Elmore City, OK 73433 Phone: (580) 788-2187 E-mail: splcontrol@aol.com (Mr. Tom Luster) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Workers should be in well ventilated areas; if in a confined area, use a respirator. 3. Skin and eye contact; protective clothing; treatment in case of contact: Workers should wear protective goggles or safety glasses. Prolonged contact with skin may result in dryness. 4.a. Maximum storage temperature: NA 4.b. Minimum storage temperature: >32°F 4.c. Optimum storage temperature range: 40°F to 200°F 4.d. Temperatures of phase separations and chemical changes: No phase separation or hazardous polymerization will occur. V. SHELF LIFE Indefinite. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: NALE-IT may be applied using a pressure sprayer. 2. Concentration/Application Rate: For pit closures, surface hydrocarbon spills, compressor Surface Washing Agents 294 NALE-IT ------- stations, pipeline and flow line leaks, well head and tank farm leaks, and highway spills, (petroleum products) mix 1 part NALE-IT with 20 parts water. 3. Conditions for Use: Equally effective with fresh or salt water. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested NALE-IT No. 2 Fuel Oil NALE-IT & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) b. Effectiveness: NA Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: 30°F 3. Viscosity: 1.18 4. Specific Gravity: 1.02 5. pH: 6.8-7.2 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility in Water: Soluble in fresh and sat water. LC50 (ppm) 273.30 96-hr 69.00 48-hr 6.93 96-hr 2.29 48-hr 3.82 96-hr 1.84 48-hr 2.60 96-hr 8.56 48-hr Surface Washing Agents 295 NALE-IT ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.82 ND ND 0.173 ND ND ND 0.18 ND ND Surface Washing Agents 296 NALE-IT ------- TECHNICAL PRODUCT BULLETIN #SW-30 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JULY 24, 2002 "F-500" I. NAME, BRAND, OR TRADEMARK F-500 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Hazard Control Technologies, Inc. 150 Walter Way Fayetteville, GA 30214 Phone: (770)719-5112 Fax: (770)719-5117 E-mail: egriffin@hct-world.com (Ms. Esther Griffin) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Hazard Control Technologies, Inc. 150 Walter Way Fayetteville, GA 30214 Phone: (770)719-5112 Fax: (770)719-5117 E-mail: egriffin@hct-world.com (Ms. Esther Griffin) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Local exhaust - no special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: Eye contact - may cause eye irritation, flush with water. Wear splash proof protection goggles or full-face shield. If irritation persists contact a physician. Skin contact - may cause mild irritation, flush with water. Wear rubber and vinyl gloves and apron. Product has been tested and found to be non- skin sensitizing per OECD 406. Ingestion - may cause gastrointestinal irritation. Drink plenty of water to dilute. Do not induce vomiting. If irritation persists contact a physician. Inhalation - elevated temperature vapors may cause irritation to respiratory tract. Remove to fresh air. 4.a. Maximum storage temperature: 130°F 4.b. Minimum storage temperature: 17°F 4.c. Optimum storage temperature range: 35°F - 130°F 4.d. Temperatures of phase separations and chemical changes: NA Surface Washing Agents 297 F-500 ------- V. SHELF LIFE The shelf life is 15 years when stored between 35°F - 130°F in unopened containers. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Standard fire apparatus spray nozzle with agitation onto and into spill. 2. Concentration/Application Rate: 1 part F-500:8 parts hydrocarbon:32 parts water (fresh or salt). 3. Conditions for Use: Water temperature: 33°F - 211°F. Effective on both polar and non-polar hydrocarbons VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested F-500 No. 2 Fuel Oil F-500 & No. 2 Fuel Oil (1:10) Reference Toxicant (DSS) b. Effectiveness: NA Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) <10.00 96-hr 32.00 48-hr 56.00 96-hr 100.00 48-hr <10.00 96-hr 32.00 48-hr 1.14 96-hr 0.98 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: -17°F 3. Viscosity: 54-56 centistokes @ 72°F 4. Specific Gravity: 0.99 g/cc @ 72°F 5. pH: 7.00 6. Surface Active Agents: PROPRIETARY/CONFIDENTIAL 7. Solvents: None 8. Additives: None 9. Solubility in Water: Complete Surface Washing Agents 298 F-500 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) <0.03 <0.01 <0.01 <0.05 <0.025 <0.005 <0.02 <0.07 <0.02 <0.10 Surface Washing Agents 299 F-500 ------- TECHNICAL PRODUCT BULLETIN #SW-31 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: OCTOBER 27, 2003 "ENVIROCLEAN" I. NAME, BRAND, OR TRADEMARK ENVIROCLEAN Type of Product: Surface Washing Agent (formerly ENVIRO CLEAN 165) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Blind Gate Holdings, LLC 14 Largo Woods Place The Woodlands, TX 77382 Phone: (281)216-6363 E-mail: igibson@evergreenchems.com E-mail: mgibson@ever greenchems.com Website: www, ever greenchem s. com (Mr. Jonathan Gibson) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Evergreen Chemical Solutions, LLC 6700 Woodlands Parkway, Suite 230-250 Spring, TX 77382 Phone: 281-216-6363 E-mail: igibson@evergreenchems.com Website: www, ever greenchem s. com (Mr. Jonathan Gibson) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Normal. 3. Skin and eye contact; protective clothing; treatment in case of contact: Use good normal hygiene and avoid contact with skin and eyes. Gloves and goggles are recommended for field application and product handling. If contact with eyes flush with water for 15 minutes and seek medical attention. For contact with skin, wash area with soap and water. May cause redness, edema, and drying of skin. Seek medical attention if irritation develops. In case of ingestion, seek medical attention. Not considered an inhalation risk. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 28°F 4.c. Optimum storage temperature range: 30°F - 120°F 4.d. Temperatures of phase separations and chemical changes: Temperature fluctuations will not Surface Washing Agents 300 ENVIROCLEAN ------- cause separation or deterioration of product. Product blend is stable and will not undergo phase separation of ingredients or stratification of contents over time. V. SHELF LIFE Unlimited if unopened. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Dilute product with water prior to use. Apply product via manual pressure applicator (i.e., hand pump), or other delivery equipment, to impacted surfaces. Allow product to soak prior to rinse/recovery if heavily saturated with oil. On hard surfaces, product may be applied and agitated with a brush or other physical means prior to recovery of effluent. Product may also be pre-mixed and used in a batch tank or through an eduction/metering system for flushing and recovery operations. 2. Concentration/Application Rate: ENVIROCLEAN is a concentrated product and must be diluted prior to use. Concentrations vary based upon type of oil and degree of surface saturation. For light ends (i.e., gas condensate/gasoline) a 1% - 2% solution may be used to flush area to containment. (A higher concentration solution of 6% should be used if flammable vapor presents an explosion hazard.) For lighter oils (i.e., No. 2 Fuel Oil) a 3% solution may be used to flush impacted areas to containment. For heavy ends (i.e., crude oil/No. 6 Fuel Oil) a 6% solution of ENVIROCLEAN should be applied and allowed to soak into containment/substrate for up to an hour to allow for release of oil. The surface should then be flushed to containment with a 1% - 3% solution of ENVIROCLEAN. Product may be used as noted above through any pressure or steam equipment. The use of a "hot" unit is recommended when oils are at low temperature or have been weathered. 3. Conditions for Use: ENVIROCLEAN may be diluted with hard, soft, brackish, salt, or most waters of sufficient quality for operations. Surface Washing Agents 301 ENVIROCLEAN ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) ENVIROCLEAN Menidia beryllina 27.80 96-hr Mysidopsis bahia 22.60 48 hr No. 2 Fuel Oil Menidia beryllina 8.77 96-hr Mysidopsis bahia 1.53 48-hr ENVIROCLEAN& No. 2 Fuel Oil (1:10) Menidia beryllina 8.13 96-hr Mysidopsis bahia 1.76 48 hr Reference Toxicant (DSS) Menidia beryllina 1.83 96-hr Mysidopsis bahia 3.37 48 hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: 28.8°F 3. Viscosity: 9 Centipose 4. Specific Gravity: 1.028 5. pH: 8.63 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility in Water: Complete X. ANALYSIS FOR HEAVY METALS, CYANIDE, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons AND CHLORINATED Concentration (ppm) <0.002 <0.001 <0.005 <0.002 <0.005 <0.0002 <0.005 <0.002 <0.1 <0.05 Surface Washing Agents 302 ENVIROCLEAN ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-32 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 21, 2006 "BG-CLEAN™ 401" I. NAME, BRAND, OR TRADEMARK BG-CLEAN™ 401 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Amiran BioChemicals, LLC 7221 South 10th Street Oak Creek, WI 53154 Phone: updated information required Fax: updated information required (Dr. Mohsen Amiran) Phone: updated information required Fax: updated information required E-mail: updated information required (Mr. Sherwin Amiran) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Amiran BioChemicals, LLC 7221 South 10th Street Oak Creek, WI 53154 Phone: updated information required Fax: updated information required (Dr. Mohsen Amiran) BioCenter, Inc. P.O. Box 170498 Milwaukee, WI 53217 Phone: (414) 768-7100 Fax: (414)768-7106 E-mail: skelling@aol.com (Mr. Scott Kelling) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: BG-CLEAN™ 401 is not classified as flammable by either USDOT or IMO regulations. 3/09/2016 7/27/2022 Surface Washing Agents 303 BG-CLEAN™ 401 ------- 2. Ventilation: Avoid prolonged breathing of vapors. 3. Skin and eye contact; protective clothing; treatment in case of contact: BG-CLEAN™ 401 is an organic compound with a slightly alkaline pH. No extraordinary precautions are required during handling. Avoid unnecessary contact with skin or eyes. No special protective clothing is required. Body areas exposed to BG-CLEAN™ 401 may be flushed with water to clean off the chemical. 4.a. Maximum storage temperature: 180°F 4.b. Minimum storage temperature: -25°F 4.c. Optimum storage temperature range: 68°F 4.d. Temperatures of phase separations and chemical changes: BG-CLEAN™ 401 is not adversely affected by changes in storage temperature unless evaporation is allowed to occur. Phase separation does not occur when the product is stored in below freezing conditions. BG- CLEAN™ 401 is ready for use as soon as it is rewarmed to approximately 34-40°F. Product will expand when frozen. V. SHELF LIFE The shelf life of unopened containers of BG-CLEAN™ 401 is unlimited. Containers should always be capped when not in use to prevent contamination and evaporation. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: BG-CLEAN™ 401 is applied by one of two methods. 1) For situations where cleanup starts shortly after contamination and the oil has not yet weathered, use a high pressure spray. BG-CLEAN™ 401 is proportioned into a stream of water and sprayed directly on the surface to be cleaned at a rate of 60-70 gpm. 2) For difficult cleaning situations such as weathered crude oil on a rocky beach, a three step procedure should be used. First presoak the contaminated area by proportioning BG-CLEAN™ 401 into a low pressure stream of water at a rate of about 20 gpm. Allow the spray to soak for 15-30 minutes. Then proportion BG- CLEAN™ 401 into a high pressure water stream and apply at a rate of 60-70 gpm. Selection of the best procedure depends on site conditions. BG-CLEAN™ 401 effectiveness is increased when applied with water heated to between 100°F and 180°F. As ambient temperature decreases, the benefits of applying heated spray increase. The efficiency of BG-CLEAN™ 401 depends directly on mixing of the BG-CLEAN™ 401 molecules with the hydrocarbon molecules. Given good mixing, BG-CLEAN™ 401 can be used on all hydrocarbons except asphalt. 2. Concentration/Application Rate: Dilute BG-CLEAN™ 401 water. The amount of spray required varies with the amount of oil. Concentrations ranging from 5:1 to 100:1 have been found useful depending on hydrocarbon concentrations and viscosity. During application, adjust the concentration of BG-CLEAN™ 401 to suit the cleaning effect desired. 3. Conditions for Use: BG-CLEAN™ 401 is recommended as a cleaner for piers, seawalls, pilings, ship's hulls, and rocky beaches. It can be used on metal, wood, and plastics. BG- CLEAN™ 401 is also highly useful for cleaning contaminated solids such as soil. This includes a range from normal soil aggregate to 100% sand. Two conditions are required for maximum cleaning; thorough mixing of BG-CLEAN™ 401 with the oil and an adequate concentration of Surface Washing Agents 304 BG-CLEAN™ 401 ------- BG-CLEAN™ 401. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested BG-CLEAN™ 401 No. 2 Fuel Oil BG-CLEAN™ 401 No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) b. Effectiveness: NA Species LC50 (ppm) Menidia beryllina 787. .00 96-hr Mysidopsis bahia 477. .00 48-hr Menidia beryllina 16. .90 96-hr Mysidopsis bahia 2. .92 48-hr Menidia beryllina 13. .10 96-hr Mysidopsis bahia 2. .86 48-hr Menidia beryllina 3. .93 96-hr Mysidopsis bahia 8. .80 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM D-93: >76.6°C (>170°F) 2. Pour Point, ASTM D-97: -4°C 3. Viscosity, ASTMD-88: 24 SUS@ 100°F 4. Specific Gravity, ASTM D-1298: 1.00604 @ 60°F 5. pH: 8.227 6. Surface Active Agents: Proprietary 7. Solvents: Proprietary 8. Additives: Proprietary 9. Solubility: Miscible in water. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.118 Cadmium <0.020 Chromium <0.125 Copper 0.049 Lead 0.166 Mercury <0.02 Nickel <0.125 Zinc 0.280 Cyanide 0.002 Chlorinated Hydrocarbons ND Surface Washing Agents 305 BG-CLEAN™ 401 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 7/15/2021 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-33 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 27, 2006 "E-SAFE®" I. NAME, BRAND, OR TRADEMARK E-SAFE® Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT PLUTUS Environmental Technologies, Inc. 3138 Hatcher Mountain Road 300 John L Marshall Drive Sevierville, TN 37862-8323 Phone: (865)214-0350 E-mail: plutusceo@mail.com (Mr. James Hatcher) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS PLUTUS Environmental Technologies, Inc. 3138 Hatcher Mountain Road 300 John L Marshall Drive Sevierville, TN 37862-8323 Phone: (865)214-0350 E-mail: plutusceo@mail.com (Mr. James Hatcher) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable until >170°F 2. Ventilation: Handle in a well-ventilated space. Local exhaust is recommended if TLV's are exceeded. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye and (sensitive) skin contact. In case of contact, immediately flush with large amount of cool water of at least 5 minutes. Wear protective eye goggles when using any chemicals. Impermeable protective gloves are recommended for sensitive skin types. Protective clothing is not required. Rinse contaminated clothing, shoes, goggles, and gloves in simple tap water to remove any chemical residue. Avoid ingestion, breathing dusts, mists, or fumes. In case of ingestion drink several glasses of water. Do not induce vomiting. In case of inhalation, move affected person to fresh air. 4.a. Maximum storage temperature: 160°F Surface Washing Agents 306 E-SAFE® ------- 4.b. Minimum storage temperature: -15°F 4.c. Optimum storage temperature range: 40°F - 110°F 4.d. Temperatures of phase separations and chemical changes: No phase separations will occur. Continued exposure to direct sunlight may cause a change in color, but performance is not affected. V. SHELF LIFE Unlimited if left in unopened containers stored at 40°F - 110°F and away from direct sunlight. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: E-SAFE® may be introduced with a pressure spray to cover the affected area. The contaminated area should be thoroughly moistened. Following the spray application the treated area should be soaked with water to facilitate penetration. Heavy soil such as clay will be cleaned by E-SAFE®, but tilling or aerating the soil will rapidly shorten penetration time. Sand or loam ay require heavy dosage with E-SAFE® because hydrocarbon migration is so rapid in these soil types. Treatment of fouled beach areas should have E-SAFE® sprayed on all contaminated surfaces. Any remaining hydrocarbons may then be effectively vacuumed or wiped away from the treated surfaces. Incidental wave action or rainfall will enhance coverage and penetration by E-SAFE®. 2. Concentration/Application Rate: E-SAFE® should be applied full strength. Beginning treatment for hydrocarbon contaminated surface is one gallon of E-SAFE® per 100 square foot of surface area. This dosage is recommended when the ambient temperature is 72°F and humidity is moderate. Higher temperature or lower humidity will increase the need for repeated applications or a higher volume of E-SAFE® per application. 3. Conditions for Use: E-SAFE® works on all soil types and weather conditions that allow hydrocarbon penetration. E-SAFE® follows the same path, channel, or gradient as the contaminant. When visible detection reveals that E-SAFE® has been absorbed by, or has penetrated the soil, water should be applied to the site. E-SAFE® is soluble in water and also breaks the surface tension of the transporting water molecules. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested E-SAFE® Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 329.00 96-hr 257.00 48-hr 5.45 96-hr 10.20 48-hr 8.77 96-hr 14.20 48-hr 8.07 96-hr 16.00 48-hr No. 2 Fuel Oil E-SAFE® No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) b. Effectiveness: NA Surface Washing Agents 307 E-SAFE® ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM D-93: >170°F 2. Pour Point, ASTM D-97: -27°C 3. Viscosity, ASTMD-88: 11SFS@ 100°F 4. Specific Gravity, ASTM D-1298: 1.0118 @ 60°F 5. pH: 8.04 6. Surface Active Agents: Confidential 7. Solvents: Confidential 8. Additives: Confidential 9. Solubility: Soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.005 Cadmium <0.0008 Chromium <0.025 Copper 0.061 Lead 0.082 Mercury <0.007 Nickel <0.003 Zinc 0.214 Cyanide 0.200 Chlorinated Hydrocarbons ND Surface Washing Agents 308 E-SAFE® ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 7/15/2021 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-34 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 27, 2006 "SHEEN-MAGIC®" I. NAME, BRAND, OR TRADEMARK SHEEN-MAGIC® Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT PLUTUS Environmental Technologies, Inc. 3138 Hatcher Mountain Road 300 John L Marshall Drive Sevierville, TN 37862-8323 Phone: (865)214-0350 E-mail: plutusceo@mail.com (Mr. James Hatcher) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS PLUTUS Environmental Technologies, Inc. 3138 Hatcher Mountain Road 300 John L Marshall Drive Sevierville, TN 37862-8323 Phone: (865)214-0350 E-mail: plutusceo@mail.com (Mr. James Hatcher) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable until >170°F 2. Ventilation: Handle in a well-ventilated space. Local exhaust is recommended if TLV's are exceeded. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye and (sensitive) skin contact. In case of contact, immediately flush with large amount of cool water of at least 5 minutes. Wear protective eye goggles when using any chemicals. Impermeable protective gloves are recommended for sensitive skin types. Protective clothing is not required. Rinse contaminated clothing, shoes, goggles, and gloves in simple tap water to remove any chemical residue. Avoid ingestion, breathing dusts, mists, or fumes. In case of ingestion drink several glasses of water. Do not induce vomiting. In case of inhalation, move affected person to fresh air. 4.a. Maximum storage temperature: 160°F Surface Washing Agents 309 SHEEN-MAGIC® ------- 4.b. Minimum storage temperature: -8°F 4.c. Optimum storage temperature range: 40°F - 110°F 4.d. Temperatures of phase separations and chemical changes: No phase separations will occur. V. SHELF LIFE Unlimited if left in unopened containers stored at 40°F - 110°F and away from direct sunlight. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: SHEEN-MAGIC® recommended treatment is light misting of contaminated surface. Heavier hydrocarbons such as crude oil should be boomed or vacuumed away as much as possible before application of the SHEENMAGIC®. Treatment of fouled beach areas should have SHEEN-MAGIC® sprayed on all contaminated surfaces. Incidental wave action or rainfall will enhance coverage and penetration by SHEEN-MAGIC®. Any remaining hydrocarbons may then be effectively vacuumed or wiped away from the treated surfaces. Aerial application should be delivered at height and air speed that will create air shear necessary to deliver droplets as per nozzle manufacturer's recommendations. Mist spray from surface vehicles may be delivered from power fogger units. Hand sprayers are generally used for small treatment areas. 2. Concentration/Application Rate: One ounce per 50 square yards of surface is the normal treatment for diesel spills. Heavier hydrocarbon sheens may require additional treatment to remove the contaminant. 3. Conditions for Use: SHEEN-MAGIC® works in all weather conditions that allow hydrocarbon penetration. SHEEN-MAGIC® should be used as soon as the temperature and weather conditions allow delivery to the spill area. Heavier concentrations may be required when the temperature/humidity will cause rapid evaporation of the spray. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) SHEEN-MAGIC® Menidia beryllina 183.00 96-hr Mysidopsis bahia 161.00 48-hr No. 2 Fuel Oil Menidia beryllina 4.57 96-hr Mysidopsis bahia 3.04 48-hr SHEEN-MAGIC® Menidia beryllina 7.82 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 5.75 48-hr Reference Toxicant (SDS) Menidia beryllina 11.70 96-hr Mysidopsis bahia 5.36 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Surface Washing Agents 310 SHEEN-MAGIC® ------- IX. PHYSICAL PROPERTIES 1. Flash Point, ASTM D-93: >170°F 2. Pour Point, ASTM D-97: -22°C 3. Viscosity, ASTMD-88: 11SFS@ 100°F 4. Specific Gravity, ASTM D-1298: 1.0127 @ 60°F 5. pH: 8.10 6. Surface Active Agents: Confidential 7. Solvents: Confidential 8. Additives: Confidential 9. Solubility: Soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.005 Cadmium <0.0008 Chromium 0.026 Copper 0.023 Lead 0.085 Mercury <0.007 Nickel <0.003 Zinc 0.231 Cyanide 0.200 Chlorinated Hydrocarbons ND Surface Washing Agents 311 SHEEN- ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-35 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JUNE 16, 2008 "PROCLEANS" I. NAME, BRAND, OR TRADEMARK PROCLEANS Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Eximco International, Inc. 5250 Gulfton, #2-B Houston, TX 77081 Phone: updated information required E-mail: updated information required (Mr. Nat Brown) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Eximco International, Inc. 5250 Gulfton, #2-B Houston, TX 77081 Phone: updated information required E-mail: updated information required E-mail: (Mr. Nat Brown) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Normal. 3. Skin and eye contact; protective clothing; treatment in case of contact: Flush contaminated eyes thoroughly with water for 15 minutes, and get medical attention. Remove contaminated clothing, wash exposed area with soap and water, and wash clothing before use. Get medical attention if irritation develops. Get medical attention if ingested. No medical attention is necessary if inhaled. 4.a. Maximum storage temperature: 130°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 50°F to 100°F 4.d. Temperatures of phase separations and chemical changes: NA 3/16/2016 7/27/2022 Surface Washing Agents 312 PROCLEANS ------- V. SHELF LIFE Approximately 2 years at recommended temperatures if unopened. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Apply specified dilute solution using fire hoses or heated pressure washers onto the contaminated solid surface of the spill. 2. Concentration/Application Rate: Use ten parts water to one part product. Dilution rates may be adjusted to suit different job conditions. Apply 10 to 15 gallons of diluted PROCLEANS to one cubic yard of contamination. 3. Conditions for Use: May be used with fresh or salt water. Warmer temperatures may improve results. Most effective if used on solid surfaces such as shoreline beaches and rocks contaminated with light and medium weight crude oils and refined petroleum products. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) PROCLEANS Menidia beryllina 83.73 96-hr Mysidopsis bahia 83.98 48-hr No. 2 Fuel Oil Menidia beryllina 7.41 96-hr Mysidopsis bahia 11.68 48-hr PROCLEANS & Menidia beryllina 4.78 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 11.68 48-hr Reference Toxicant (CuS04) Menidia beryllina 0.73 96-hr Mysidopsis bahia 0.77 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >186°F 2. Pour Point: 34.6°F 3. Viscosity: 2.41 cST @ 104°F 4. Specific Gravity: 1.01 @ 25°C 5. pH: 6.8 6. Surface Active Agents: Anionic and nonionic 7. Solvents: None. 8. Additives: None 9. Solubility in Water: NA Surface Washing Agents 313 PROCLEANS ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.690 ND ND ND ND ND ND 0.738 ND ND Surface Washing Agents 314 PROCLEANS ------- TECHNICAL PRODUCT BULLETIN #SW-36 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 30, 2009 "SPILLCLEAN" SPILLCLEAN ["Concentrate"] (aka, FIREMAN'S BRAND SPILLCLEAN) I. NAME, BRAND, OR TRADEMARK SPILLCLEAN SPILLCLEAN ["Concentrate"] = 30% Active Ingredients and 70% Water (aka, FIREMAN'S BRAND SPILLCLEAN) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Super Sat Ventures, Inc. S96 W34577 Jericho Drive Eagle, WI 53119 Phone: (414) 840-9223 E-mail: dwk@ssvinc.com (Mr. Daniel W. Klein) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Super Sat Ventures, Inc. S96 W34577 Jericho Drive Eagle, WI 53119 Phone: (414) 840-9223 E-mail: dwk@ssvinc.com (Mr. Daniel W. Klein) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: >210°F 2. Ventilation: General room ventilation is expected to be satisfactory. 3. Skin and eye contact; protective clothing; treatment in case of contact: Product may cause mild skin irritation. Wear impervious gloves, safety goggles, and full cover clothes. Eye wash and safety shower should be accessible. If eye contact, flush immediately with water for at least 15 minutes. If skin contact, wash with soap and water. If swallowed, give two glasses of water (do not induce vomiting). Seek medical attention for eye and skin contact and ingestion. 4.a. Maximum storage temperature: <210°F 4.b. Minimum storage temperature: >32°F 4.c. Optimum storage temperature range: 50°F - 70°F 4.d. Temperatures of phase separations and chemical changes: <32°F and >210°F Surface Washing Agents 315 SPILLCLEAN [CONCENTRATE] ------- V. SHELF LIFE 3 years. Avoid extreme heat and store in a dry, cool area. VI. RECOMMENDED APPLICATION PROCEDURES Please note: SPILLCLEAN comes in two forms "Concentrate" and "Original Formula." SPILLCLEAN ["Concentrate"] is 30% Active Ingredients and 70% Water while SPILLCLEAN ["Original Formula"] is 10% Active Ingredients and 90% Water. SPILLCLEAN ["Concentrate"] and SPILLCLEAN ["Original Formula"] are for on land and surface use only. They should not be used around or near bodies of water when there is a reasonable chance of mixing in with water. Once the contaminant/SPILLCLEAN ["Concentrate"] solution mixes with the body of water, "control" of the contaminant will be lost since SPILLCLEAN is water soluble. SPILLCLEAN is a formula designed to solubilize and emulsify oil and oil-type products such as motor oil, gasoline, diesel fuel, and transmission fluid. When such products are accidentally spilled and need to be cleaned up from hard surfaces such as streets and driveways, SPILLCLEAN is an effective material to use. Being a surfactant-type material, SPILLCLEAN allows the spilled contaminant to be emulsified and then lifted and separated from the hard surface. The resulting spill/contaminant can then be picked up, vacuumed up, or flushed with water, all in accordance with federal, state, and local regulations. 1. Application Method: SPILLCLEAN ["Concentrate"] 30% Active Ingredients and 70% Water - squeeze product directly around outside perimeter of oil/gasoline/antifreeze spill using squeeze bottle container. This process is designed to "contain" the contaminant and keep if from migrating down a hard surface like a city street, parking lot, or garage floor. SPILLCLEAN ["Concentrate"] is more viscous than oil/gasoline, and will "hold" the contaminant in place. Once the contaminant is contained, the user can apply SPILLCLEAN ["Original Formula"] over the "body" of the contaminant if the spill is large (over 2 gallons). If the spill is small (less than 2 gallons), the user can apply either SPILLCLEAN ["Concentrate"] or SPILLCLEAN ["Original Formula"] to the "body" of the contaminant spill. Using a broom or broom-like applicator, sweep SPILLCLEAN in with the contaminant until thoroughly blended in place. The original bright red color of SPILLCLEAN ["Concentrate"] and SPILLCLEAN ["Original Formula"] will dissipate when it is thoroughly mixed with the contaminant. SPILLCLEAN ["Original Formula"] 10%) Active Ingredients and 90%) Water - apply over the "body" of the contaminant if the spill is large (over 2 gallons). If the spill is small (less than 2 gallons), the user can apply SPILLCLEAN ["Concentrate"] or SPILLCLEAN ["Original Formula"] to the "body" of the contaminant spill. SPILLCLEAN ["Original Formula"] is designed to "attach" to a contaminant and remove it from a hard surface like a city street, parking lot, or garage floor. It is recommended to be used on any size contaminant spill, large or small. This product is designed to penetrate into the surface pores and molecularly "attach" with the contaminant, thus making the contaminant "water soluble." The contaminant can be removed Surface Washing Agents 316 SPILLCLEAN [CONCENTRATE] ------- from the pores (of the asphalt, concrete, epoxy surface, etc.) with a 60psi water supply. The user can then dispose of the resulting mixture according to regulations. This product can be applied using a vast number of different applicators, especially with regard to firefighting equipment. Using a broom or broom-like applicator, sweep SPILLCLEAN in with the contaminant until thoroughly blended in place. The original bright red color of SPILLCLEAN ["Concentrate"] and SPILLCLEAN ["Original Formula"] will dissipate when it is thoroughly mixed with the contaminant. When SPILLCLEAN'S bright red color has dissipated (upon mixing) with the contaminant, it can be wiped clean with a rag or wet-vacuumed, collected, and disposed of according to EPA, federal, state, and local regulations. Additionally, a dry sorbent may be applied to the resulting SPILLCLEAN/contaminant/water mixture, shoveled up and disposed of according to applicable regulations. 2. Concentration/Application Rate: For Surface and Land Application Only: SPILLCLEAN ["Concentrate"] 30% Active Ingredients and 70% Water - for spills less than 2 gallons squeeze a one-half inch ribbon of straight product around the perimeter of the oil/gasoline spill, followed by an "X" pattern over the body of the spill. For spills greater than 2 gallons squeeze a one-half inch ribbon of straight product around the perimeter of the oil/gasoline spill. The general purpose of SPILLCLEAN ["Concentrate"] is to "contain" the contaminant from migrating, and therefore should not be diluted with water during application. SPILLCLEAN ["Original Formula"] 10% Active Ingredients and 90% Water - concentration rate is based on equipment used and disposal method. Typical usage will be (0 to 100 parts water) plus 1 part SPILLCLEAN ["Original Formula"] all applied to 1 part contaminant (oil/gasoline spill). The resulting mixture of SPILLCLEAN and oil must be disposed of in accordance with EPA, federal, state, and local agencies that regulate disposal of contaminant. The resulting SPILLCLEAN contaminant mixture should be wet-vacuumed up and placed in a proper container and disposed. 3. Conditions for Use: Water Salinity: Water soluble, not applicable for use on water Water Temperature: >32°F and <120°F Types of Pollutants: Automobile motor oil, gasoline, diesel fuel, and transmission fluid Ages of Pollutants: 0 to 20 years old VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) SPILLCLEAN ["Concentrate"] Menidia beryllina 24.30 96-hr Mysidopsis bahia 10.00 48-hr Surface Washing Agents 317 SPILLCLEAN [CONCENTRATE] ------- No. 2 Fuel Oil SPILLCLEAN ["Concentrate"] & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia 6.60 96-hr 2.20 48-hr 3.30 96-hr 1.30 48-hr 8.90 96-hr 10.70 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: SPILLCLEAN ["Concentrate"] = >210°F 2. Pour Point: SPILLCLEAN ["Concentrate"] = 27.0°F 3. Viscosity: SPILLCLEAN ["Concentrate"] = 6400cPs@25°C 4. Specific Gravity: SPILLCLEAN ["Concentrate"] = 1.030 5. pH: SPILLCLEAN ["Concentrate"] = 7.20 6. Surface Active Agents: Confidential 7. Solvents: Confidential 8. Additives: Confidential 9. Solubility: Water soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.02 <0.007 <0.01 <0.01 <0.02 <0.00003 <0.01 <0.01 0.137 <0.01 Surface Washing Agents 318 SPILLCLEAN [CONCENTRATE] ------- TECHNICAL PRODUCT BULLETIN #SW-37 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 15, 2010 "TXCHEM HE-1000™" I. NAME, BRAND, OR TRADEMARK TXCHEM HE-1000™ Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Texas EnviroChem, Inc. 17890 Airfield Lane Pearland, TX 77581 Phone: (713) 806-4099 (Mr. Pete Franks) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Texas EnviroChem, Inc. 17890 Airfield Lane Pearland, TX 77581 Phone: (713) 806-4099 (Mr. Pete Franks) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Not flammable 2. Ventilation: Recommended, respirator in confined area 3. Skin and eye contact; protective clothing; treatment in case of contact: Wear rubber gloves and eye protection. If eye contact, wash eyes thoroughly for 15 minutes; including upper and lowers lids, and seek medical attention. For skin contact, irritation is possible, wash with soap and water for 15 minutes. If irritation persists, seek medical attention. 4.a. Maximum storage temperature: 95°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 75°F 4.d. Temperatures of phase separations and chemical changes: No phase changes have been observed. V. SHELF LIFE One year in a sealed container. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: TXCHEM HE-1000™ is applied by pressure sprayer, heated pressure washer, fire hoses or mixing on or into hydrocarbon contaminated media. Surface Washing Agents 319 TXCHEM HE-1000™ ------- 2. Concentration/Application Rate: TXCHEM HE-1000™ should be diluted to a one (1) part concentrated chemical to ten (10) parts water solution. Apply ten to fifteen gallons of diluted solution to one cubic yard of contaminated media. Agitate to slurry. Dilution rate may change due to level of hydrocarbon contamination. Please see manufacturer's instructions for additional application dilutions. Excess washing solution should be disposed of according to local, state, and federal regulations. 3. Conditions for Use: Pollutants should be of hydrocarbon in nature. Greater results occur at ambient temperatures greater than 50°F. Fresh or salt water can be used with no performance change. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) TXCHEM HE-1000™ Menidia beryllina 91.33 96-hr Mysidopsis bahia 65.52 48-hr No. 2 Fuel Oil Menidia beryllina 5.84 96-hr Mysidopsis bahia 2.17 48-hr TXCHEM HE-1000™ & Menidia beryllina 7.07 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.11 48-hr Reference Toxicant (SLS) Menidia beryllina 15.27 96-hr Mysidopsis bahia 12.84 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >210°F 2. Pour Point: 23.0°F 3. Viscosity: 1.99cSt 4. Specific Gravity: 0.999 5. pH: 7.20 6. Surface Active Agents: Confidential 7. Solvents: NA 8. Additives: Confidential 9. Solubility: NA X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium 0.0366 Surface Washing Agents 320 TXCHEM HE-1000™ ------- Copper 0.0402 Lead 0.0189 Mercury ND Nickel 0.0125 Zinc 0.29 Cyanide <0.05 Chlorinated Hydrocarbons ND Surface Washing Agents 321 TXCHEM HE-1000™ ------- TECHNICAL PRODUCT BULLETIN #SW-38 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MAY 11, 2010 "NOKOMIS 5-W" I. NAME, BRAND, OR TRADEMARK NOKOMIS 5-W Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Mar-Len Supply, Inc. 23159 Kidder Street Hayward, CA 94545 Phone: (510) 782-3555 Fax: (510) 782-2032 E-mail: marlensupply@vahoo.com (Mrs. Shirley Winter or Mr. Curt Winter) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Mar-Len Supply, Inc. 23159 Kidder Street Hayward, CA 94545 Phone: (510) 782-3555 Fax:(510)782-2032 E-mail: marlensupplv@vahoo.com (Mrs. Shirley Winter or Mr. Curt Winter) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (water based) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of eye contact, flush with water; in case of skin contact, wash with water; and, if swallowed drink water to dilute and induce vomiting. 4.a. Maximum storage temperature: 212°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 50°F 4.d. Temperatures of phase separations and chemical changes: NA V. SHELF LIFE 15 years or more if stored correctly in plastic drums. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: NOKOMIS 5-W is a concentrated liquid, non-hazardous cleaner. Can be Surface Washing Agents 322 NOKOMIS 5-W ------- used full strength or diluted with fresh or salt water. NOKOMIS 5-W is marketed in plastic containers. 2. Concentration/Application Rate: Dilution ratios are determined by the individual cleaning application. For washing equipment contaminated with soluble crude and/or bunker fuel oil use a 5:1 cleaning solution. Spray or brush onto surface, agitate with a stiff bristle brush, and rinse with fresh or salt water. For pressure washing, pre-spray surface with concentrate and allow to dwell on surface one to ten minutes (depending on age of oil). For shoreline areas and beaches with rocky, breakwaters contain the area of beach sand and gravel by creating a sand bather around a small contaminated area. Spray contaminated area with a 10:1 solution. Add salt or freshwater, agitate surface to help release oil from sand. Allow time for oil to surface and recover oil. To clean larger tidal rock surfaces, apply 5:1 or 20 percent mixture of NOKOMIS 5-W. Spray solution onto rocks with a garden type pump sprayer. Agitate with a stiff bristle brush. Allow to dwell on surface until surface looks soluble. Contain with a boom or use oil absorbent pads to recover oil. 3. Conditions for Use: Fresh or salt water can be used. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested NOKOMIS 5-W No. 2 Fuel Oil NOKOMIS 5-W No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) b. Effectiveness: NA Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 10.46 21.52 4.25 2.11 3.07 2.24 13.01 9.05 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: None 2. Pour Point: 28°F 3. Viscosity: 31.00 cps 4. Specific Gravity: 1.0065 g/cc 5. pH: 10.4 6. Surface Active Agents: Confidential 7. Solvents: None 8. Additives: None 9. Solubility: Completely water soluble Surface Washing Agents 323 NOKOMIS 5-W ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.037 <0.050 <0.050 <0.050 <0.025 <0.0064 <0.050 1.7 0.042 <0.500 Surface Washing Agents 324 NOKOMIS 5-W ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-39 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 02, 2010 "G-CLEAN OSC-1809" I. NAME, BRAND, OR TRADEMARK G-CLEAN OSC-1809 (aka, OIL SPILL CLEANUP) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Green Earth Technologies 1136 Celebration Boulevard Celebration, FL 34347 Phone: (330) 540-4220 Fax: (815)331-0931 E-mail: mlukco@getg.com E-mail: iloch@getg.com Website: www.getg.com (Mr. Michael Lukco) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Green Earth Technologies 1136 Celebration Boulevard Celebration, FL 34347 Phone: (330) 540-4220 Fax: (815)331-0931 E-mail: mlukco@getg.com E-mail: iloch@getg.com Website: www.getg.com (Mr. Michael Lukco) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: As defined by OSHA's Hazard Communication Standard, this product is non-hazardous with no evidence of adverse effects. No personal protection or exposure controls. 4.a. Maximum storage temperature: 140°F continuous up to 5 days 4.b. Minimum storage temperature: 35°F 8/23/2012 7/27/2022 Surface Washing Agents 325 G-CLEAN OSC 1809 ------- 4.c. Optimum storage temperature range: 50°F to 98°F 4.d. Temperatures of phase separations and chemical changes: May begin freezing at or below 25°F as product begins to thaw. Mix product with agitator until product becomes homogenous. V. SHELF LIFE Five to ten years in sealed polydrums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Product may be applied to any surface for removal of oils. Select proper dilution depending on product types and material surface prior to application. For treatment of large areas, properly diluted product may be applied by spraying with a pressure washer, portable fire pump or any other suitable pump with seawater or freshwater suction that is equipped with a chemical inductor or feed pump. For smaller areas, properly diluted product may be applied with scrubber, mop, cloth or damp sponge. Apply liberally, adjusting dilution on site as necessary. 2. Concentration/Application Rate: For heavily weathered oil on rocks, a diluted solution of 3 parts water to 1 part product is recommended. For heavily weathered oil on beaches/sand, a diluted solution of 5 parts water to 1 part product is ideal. For tar balls, no dilution is necessary and it is suggested to apply directly at full strength. For removing oil from vegetation, a diluted solution of 10/20 parts water to 1 part product is preferred. Product may be diluted with either salt water or fresh water. Warmer waters (greater than 78°F) and/or good agitation during application will require less product. 3. Conditions for Use: Best results are obtained by allowing diluted solution to soak for at least 30 minutes to soften the oil deposits. Reapplication may be necessary in severely contaminated areas. A sorbent boom or vacuum suction equipment should be positioned to collect the washed off effluent. When proper containment equipment is in place and a soaking period of at least 30 minutes has been achieved, a diluted solution of 20 parts water and 1 part product should be applied at mid-pressure (approximately 100 PSI). Adjust the pressure and angle of the hose sprayer to achieve optimum results, adjusting dilution as necessary on site. Product and effluent should be vacuumed up or absorbed in absorbent boom and disposed of according to EPA guidelines. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) G-CLEAN OSC-1809 Menidia beryllina 11.49 96-hr Mysidopsis bahia 7.32 48-hr No. 2 Fuel Oil Menidia beryllina 2.51 96-hr Mysidopsis bahia 2.24 48-hr G-CLEAN OSC-1809 & Menidia beryllina 6.05 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.51 48-hr Reference Toxicant (SLS) Menidia beryllina 12.25 96-hr Mysidopsis bahia 11.71 48-hr Surface Washing Agents 326 G-CLEAN OSC 1809 ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: -16°F 3. Viscosity: 60.77 at40°C 4. Specific Gravity: 1.029 @60°F 5. pH: 11.3 6. Surface Active Agents: Nonionic, Surfactants, PROPRIETARY 7. Solvents: Plant-based, PROPRIETARY 8. Additives: None 9. Solubility: Completely water soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.004 Cadmium <0.002 Chromium 2.004 Copper 0.068 Lead <0.004 Mercury <1 |ig/L Nickel 0.0132 Zinc 0.0136 Cyanide <0.25 Chlorinated Hydrocarbons <5.00 Surface Washing Agents 327 G-CLEAN OSC 1809 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 3/16/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-40 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 06, 2010 "GREEN BEAST™ OIL SPILL & ODOR REMEDIATOR" (aka, GREEN BEAST WASHING AGENT; ALL PURPOSE CLEANER & REMEDIATOR) I. NAME, BRAND, OR TRADEMARK GREEN BEAST™ OIL SPILL & ODOR REMEDIATOR (aka, GREEN BEAST WASHING AGENT; ALL PURPOSE CLEANER & REMEDIATOR) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT BioFusion Corporation 310 Godwin Avenue Ridgewood, NJ 07450 Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Mr. David Gubb) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Brightside Products, LLC MSC Industrial Supply Company, Inc. 310 Godwin Avenue 75 Maxess Road Ridgewood, NJ 07450 Melville, NY 11747 Phone: updated information required Phone: (800) 645-7270 Fax: updated information required Website: www.mscdirect.com E-mail: updated information required (Mr. David Gubb) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required; however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of water. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 113°F 4.d. Temperatures of phase separations and chemical changes: Stable Surface Washing Agents 328 GREEN BEAST™ OIL SPILL & ODOR REMEDIATOR ------- V. SHELF LIFE Unlimited in sealed polydrums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: The diluted composition of the present formulation is preferably applied to a surface to be cleaned under pressure (i.e., power washing), but will work well poured directly onto the contaminated area. It is advantageous to apply the diluted final composition at high pressure, above 500 psi, but it is not required. 2. Concentration/Application Rate: For treating hydrocarbons on beaches, rocks, and hard surfaces the final composition is diluted 1:15 with fresh or sea water and is applied to the hydrocarbons at a rate of about 4 gallons for 1000 square feet of contaminated area. For spills which are of heavy consistency, the diluted mixture is preferably applied at a rate of about 1.3 gallons for 1000 square feet of contaminated area and the diluted final composition is preferably applied over a period of three consecutive days. Residue should be collected and disposed of in accordance with local, state, and federal practices and laws. 3. Conditions for Use: The composition of the present formulation is diluted into water, preferably at a temperature of about 38°F to about 60°F. While the composition is active below about 38°F, the activity is slightly reduced. The composition is also active at temperatures above about 60°F; however, at these elevated temperatures the composition is less stable and is denatured at a greater rate than at lower temperatures. Preferably, the diluted compositions of the present formulation are used immediately after the dilution into about 38°F to 60°F water. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Product No. 2 Fuel Oil Product & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) b. Effectiveness: NA Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 29.18 30.42 2.51 2.24 7.15 2.24 12.25 11.71 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >85°C 2. Pour Point: +26°F Surface Washing Agents 329 GREEN BEAST™ OIL SPILL & ODOR REMEDI AT OR ------- 3. Viscosity: 3.87 at40°C 4. Specific Gravity: 0.9986 @60°F 5. pH: 4.5 6. Surface Active Agents: Anionic andNonionic, PROPRIETARY SURFACTANTS 7. Solvents: None 8. Additives: Nutrient and Protein Package, PROPRIETARY 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.0088 Cadmium <0.002 Chromium 0.1752 Copper 0.0360 Lead <0.004 Mercury <1 |ig/L Nickel <0.010 Zinc 0.0840 Cyanide <0.010 Chlorinated Hydrocarbons <5.00 Surface Washing Agents 330 GREEN BEAST™ OIL SPILL & ODOR REMEDI AT OR ------- TECHNICAL PRODUCT BULLETIN #SW-41 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 13, 2010 "TULXA" I. NAME, BRAND, OR TRADEMARK TULXA Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Grupo Arthuriana S.A. de C.V. Cuernavaca No. 43 Colonia Condesa, Delegacion Cuauhtemoc Mexico, Distrito Federal C.P. 06140 Phone: 01 52 (55) 52 41 11 90 Fax: 01 52 (55) 53 61 13 54 E-mail: sgarcia@arthuriana. com.mx. sgarcia@onsite.com.mx or bescorcia@arthuriana.com.mx. bescorcia@onsite.com.mx Website: www.grupoarthuriana.com.mx (Ms. Susana Garcia Ballesteros) (Ms. Bertha Escorcia Rodriguez) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Grupo Arthuriana S.A. de C.V. Cuernavaca No. 43 Colonia Condesa, Delegacion Cuauhtemoc Mexico, Distri to Federal C.P. 06140 Phone: 01 52 (55) 52 41 11 90 Fax: 01 52 (55) 53 61 13 54 E-mail: sgarcia@arthuriana.com.mx, sgarcia@onsite.com.mx or bescorcia@arthuriana.com.mx, bescorcia@onsite.com.mx Website: www.grupoarthuriana.com.mx (Ms. Susana Garcia Ballesteros) (Ms. Bertha Escorcia Rodriguez) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Wear protective mask. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with eyes, in case of contact rinse with fresh water. Do not ingest. If swallowed do not induce vomiting and contact a doctor immediately. Use normal protective equipment for handling powder, such as a mask or eye shield. If eye or skin irritation occurs, flush with plenty of fresh Surface Washing Agents 331 TULXA ------- water. 4.a. Maximum storage temperature: 104°F or40°C 4.b. Minimum storage temperature: 52°F or20°C 4.c. Optimum storage temperature range: 77°F or 25°C and 95°F or 35°C 4.d. Temperatures of phase separations and chemical changes: >104°F or 40°C V. SHELF LIFE Two years if stored in dry, fresh environment. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Tulxa can be applied using conventional spraying equipment using low to moderate pressure. Tulxa can be applied directly to any surfaces coated with oil (e.g., beaches, rocks, plants). 2. Concentration/Application Rate: Tulxa can be diluted with fresh water up to a ratio of 1:200. Higher concentration of Tulxa may be required for weathered oils. Optimum concentration should be determined on site based on the type and age of the oil being removed. The product is fully miscible with water with minimal mixing. 3. Conditions for Use: It is recommended to do a test to measure the amount of oils removed and check the time and dilution at which the fats are separated. The product should completely separate the oils in 25 minutes. Although, it may be necessary to let the mixture stay in contact with surface for a longer period of time depending on the type and age of the oil. Residue should be collected and disposed of in accordance with local, state, and federal practices and laws. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) TULXA Menidia beryllina 16.50 96-hr Mysidopsis bahia 11.33 48-hr No. 2 Fuel Oil Menidia beryllina 4.94 96-hr Mysidopsis bahia 1.31 48-hr TULXA& Menidia beryllina 6.08 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.24 48-hr Reference Toxicant (SLS) Menidia beryllina 12.19 96-hr Mysidopsis bahia 10.53 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >185°F 2. Pour Point: 22°F 3. Viscosity: 30.77 cSt @ 40°C Surface Washing Agents 332 TULXA ------- 4. Specific Gravity: 1.0263 @60°F 5. pH: 5.0 6. Surface Active Agents: NA 7. Solvents: NA 8. Additives: None 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.002 Cadmium <0.001 Chromium 0.4436 Copper 0.0034 Lead <0.002 Mercury <1 |ig/L Nickel <0.005 Zinc 0.0278 Cyanide <0.013 Chlorinated Hydrocarbons <1.00 Surface Washing Agents 333 TULXA ------- TECHNICAL PRODUCT BULLETIN #SW-42 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 28, 2010 "MARINE GREEN CLEAN™" I. NAME, BRAND, OR TRADEMARK MARINE GREEN CLEAN™ Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT AGS Solutions, Inc. 5647 Nunn Street Houston, TX 77087 Phone: (713) 645-4933 Fax: (713)645-4903 E-mail: agssolutionsinc@gmail.com Website: www.agstx.com (Mrs. Linda Whiteley) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS AGS Solutions, Inc. 5647 Nunn Street Houston, TX 77087 Phone: (713) 645-4933 Fax: (713)645-4903 E-mail: agssolutionsinc@gmail.com Website: www.agstx.com (Mrs. Linda Whiteley) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Respiratory protection is not considered necessary for normal use. If exposure to vapors or mists is possible, such as is a fire emergency, NIOSH approved respiratory protection for organic vapors should be used. Mechanical ventilation is not normally required. 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of contact with eyes, wash thoroughly with plenty of clean water. Seek medical attention if irritation develops. Rubber protective gloves should be used if prolonged use of product is anticipated. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 0°F 4.c. Optimum storage temperature range: 33°F to 100°F 4.d. Temperatures of phase separations and chemical changes: >100°F Surface Washing Agents 334 MARINE GREEN CLEAN™ ------- V. SHELF LIFE Shelf life is > 2 years. The product may lose its effectiveness at temperatures >140°F. Make sure bulk containers are properly vented. Drums and similar containers should be kept closed. Store in steel or plastic containers. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: For general use, apply product by spray, mop, or with standard steam and pressure wash cleaning equipment. It can also be applied using a foam generator, or any convenient sprayer. Product can be used as is or by using heat and pressure or mechanical scrubbing. Rinse thoroughly with fresh water for a residue-free surface. In direct applications, foaming will be most effective as it will allow more contact time for the product to work. In a typical foam cleaning application operation the surface to be cleaned will be thoroughly covered with foam and allowed to stand for several minutes. The foam is rinsed away with clean water using a hot pressure of low pressure washer. Product can be applied with a variety of spraying or washing equipment, depending upon the type and scale of the shoreline or beach to be cleaned. For large areas such as beaches, the product can be sprayed from water trucks or other vehicles equipped with pumps, hoses, and nozzles to aerially deliver cleaner. On smaller oily surfaces, the product can be applied with hand sprayers or portable pumps may be used to spray directly onto oily surfaces. Dose rates may vary depending on type and amount of petroleum spilled, and other site conditions such as water, temperatures, and porosity of shoreline. Cold weather applications will require more contact time before initiating recovery. The treated product can be removed by several means including but not limited to: sorbent pads, oil skimmers, collection booms, use of vacuum trucks, berm collecting, drumming, frac tanks, or other appropriate containment and collection mechanism. 2. Concentration/Application Rate: For spills on shorelines and beaches, the product can be used undiluted up to 14% dilution with fresh water. After application, the product should be allowed to penetrate and dissolve the oily surface for up to 30 minutes, longer is preferable - if possible, to maximize contact time. For light cleaning, use up to 1:50 parts product to water. For heavy cleaning, use up to 1:14 parts product to water. 3. Conditions for Use: Product can be used in fresh or salt water, sand beaches, gravel, cobble, coarse sand and rocky shores, public beaches, and other sensitive or high impact sites. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) MARINE GREEN CLEAN™ Menidia beryllina 46.00 96-hr Mysidopsis bahia 89.00 48-hr No. 2 Fuel Oil Menidia beryllina 18.00 96-hr Mysidopsis bahia 22.00 48-hr MARINE GREEN CLEAN™ & Menidia beryllina 34.00 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 45.00 48-hr Reference Toxicant (DSS) Menidia beryllina 1.06 96-hr Mysidopsis bahia 0.97 48-hr Surface Washing Agents 335 MARINE GREEN CLEAN™ ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: NA 2. Pour Point: 30°F 3. Viscosity: 77.2 cSt @ 25°C 4. Specific Gravity: 1.032 @70°F 5. pH: 11-12.5 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: None 9. Solubility: Completely soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.648 Cadmium 0.030 Chromium 0.143 Copper 0.154 Lead <0.025 Mercury <0.013 Nickel 0.357 Zinc 2.540 Cyanide <0.02 Chlorinated Hydrocarbons ND Surface Washing Agents 336 MARINE GREEN CLEAN™ ------- TECHNICAL PRODUCT BULLETIN #SW-43 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 28, 2010 "MARINE GREEN CLEAN PLUS™" I. NAME, BRAND, OR TRADEMARK MARINE GREEN CLEAN PLUS™ Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT AGS Solutions, Inc. 5647 Nunn Street Houston, TX 77087 Phone: (713) 645-4933 Fax: (713)645-4903 E-mail: agssolutionsinc@gmail. com Website: www.agstx.com (Mrs. Linda Whiteley) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS AGS Solutions, Inc. 5647 Nunn Street Houston, TX 77087 Phone: (713) 645-4933 Fax: (713)645-4903 E-mail: agssolutionsinc@gmail. com Website: www.agstx.com (Mrs. Linda Whiteley) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Respiratory protection is not considered necessary for normal use. If exposure to vapors or mists is possible, such as is a fire emergency, NIOSH approved respiratory protection for organic vapors should be used. Mechanical ventilation is not normally required. 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of contact with eyes, wash thoroughly with plenty of clean water. Seek medical attention if irritation develops. Rubber protective gloves should be used if prolonged use of product is anticipated. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 0°F 4.c. Optimum storage temperature range: 33°F to 100°F 4.d. Temperatures of phase separations and chemical changes: >100°F Surface Washing Agents 337 MARINE GREEN PLUS™ ------- V. SHELF LIFE Shelf life is > 2 years. The product will not lose its effectiveness unless the temperatures is >140°F. Make sure bulk containers are properly vented. Drums and similar containers should be kept closed. Store in steel or plastic containers. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: For general use, apply product by spray, mop, or with standard steam and pressure wash cleaning equipment. It can also be applied using a foam generator, or any convenient sprayer. Product can be used as is or by using heat and pressure or mechanical scrubbing. Rinse thoroughly with fresh water for a residue-free surface. In direct applications, foaming will be most effective as it will allow more contact time for the product to work. In a typical foam cleaning application operation the surface to be cleaned will be thoroughly covered with foam and allowed to stand for several minutes. The foam is rinsed away with clean water using a hot pressure of low pressure washer. Product can be applied with a variety of spraying or washing equipment, depending upon the type and scale of the shoreline or beach to be cleaned. For large areas such as beaches, the product can be sprayed from water trucks or other vehicles equipped with pumps, hoses, and nozzles to aerially deliver cleaner. On smaller oily surfaces, the product can be applied with hand sprayers or portable pumps may be used to spray directly onto oily surfaces. Dose rates may vary depending on type and amount of petroleum spilled, and other site conditions such as water, temperatures, and porosity of shoreline. Cold weather applications will require more contact time before initiating recovery. The treated product can be removed by several means including but not limited to: sorbent pads, oil skimmers, collection booms, use of vacuum trucks, berm collecting, drumming, frac tanks, or other appropriate containment and collection mechanism. 2. Concentration/Application Rate: For spills on shorelines and beaches, the product can be used undiluted up to 14% dilution with fresh water. After application, the product should be allowed to penetrate and dissolve the oily surface for up to 30 minutes, longer is preferable - if possible, to maximize contact time. For light cleaning, use up to 1:200 parts product to water. For heavy cleaning, use up to 1:14 parts product to water. 3. Conditions for Use: Product can be used in fresh or salt water, sand beaches, gravel, cobble, coarse sand and rocky shores, public beaches, and other sensitive or high impact sites. Surface Washing Agents 338 MARINE GREEN PLUS™ ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested MARINE GREEN CLEAN PLUS™ No. 2 Fuel Oil MARINE GREEN CLEAN PLUS™ & No. 2 Fuel Oil (1:10) Reference Toxicant (DSS) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: NA 2. Pour Point: 28°F 3. Viscosity: 80.2 cSt @ 25°C 4. Specific Gravity: 8.6 @70°F 5. pH: 11-12.5 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Completely soluble X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Species LC50 (DDm) Menidia beryllina 28 .00 96-hr Mysidopsis bahia 53 .00 48-hr Menidia beryllina 18 .00 96-hr Mysidopsis bahia 23 .00 48-hr Menidia beryllina 30 .00 96-hr Mysidopsis bahia 32 .00 48-hr Menidia beryllina 1 .06 96-hr Mysidopsis bahia 0 .97 48-hr AND CHLORINATED Concentration (ppm) 0.827 0.025 0.078 0.062 <0.025 <0.013 0.220 1.990 <0.02 ND CYANIDE, Surface Washing Agents 339 MARINE GREEN PLUS™ ------- BULLETIN UPDATES IN BOLD TECHNICAL PRODUCT BULLETIN #SW-44 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 5, 2010 UPDATED LISTING LETTER DATE: MARCH 1, 2023 "CLEANGREEN® PLANET WASH" I. NAME, BRAND, OR TRADEMARK CLEANGREEN® PLANET WASH Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT U.S. AG, LLC P.O. Box 368 Hogansville, GA 30230 Phone: (706) 637-1111 E-mail: carl@unitedstatesag.com Website: www.unitedstatesag.com (Mr. Carl Schneider) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS U.S. AG, LLC 7054 Lone Oak Road Hogansville, GA 30230 Phone: (706) 637-1111 E-mail: carl@unitedstatesag.com Website: www.unitedstatesag.com (Mr. Carl Schneider) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required, however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable Surface Washing Agents 340 CLEANGREEN® PLANET WASH ------- V. SHELF LIFE 5 years in sealed polydrums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Product may be applied to any oil coated surface, such as beaches, equipment, rocks, etc. A variety of pumps or sprayers may be used for direct application to contaminates, back-pack, drum pumps, pick-up sprayers, etc. 2. Concentration/Application Rate: Where ever higher oil concentrations occur use approximately a 1:10 dilution ratio (product:water). Lightly soiled areas will require a 1:10 to 1:30 ratio. 3. Conditions for Use: Residue from surface washing should be collected and disposed of according to local, state, and federal regulations. The collection of residue can be determined on a site by site basis based on best practices of the area. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested CLEANGREEN® PLANET WASH No. 2 Fuel Oil CLEANGREEN® PLANET WASH & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: +25°F 3. Viscosity: 3.72 @40°C 4. Specific Gravity: 1.0691 @70°F 5. pH: 9.9 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Miscible in oil, water, and solvents Species LC50 (ppm) Menidia beryllina 136.10 96-hr Mysidopsis bahia 70.70 48-hr Menidia beryllina 3.35 96-hr Mysidopsis bahia 2.24 48-hr Menidia beryllina 4.73 96-hr Mysidopsis bahia 2.24 48-hr Menidia beryllina 12.25 96-hr Mysidopsis bahia 10.53 48-hr Surface Washing Agents 341 CLEANGREEN® PLANET WASH ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.0265 <0.005 0.0985 <0.0150 <0.0100 0.0005 <0.0250 0.2455 <0.300 <5.0 Surface Washing Agents 342 CLEANGREEN® PLANET WASH ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 8/05/2010 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-45 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 5, 2010 "SOC-10" I. NAME, BRAND, OR TRADEMARK SOC 10 (SURFACE OIL CLEANER) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Oil Treatment International AG Seestrasse 5 CH-6300 Zug Switzerland Phone: updated information required Fax: updated information required (Mr. Paul Schuler, CEO) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Eco-Oil Treatment Technologies Corporation 18 Poppy Hills Laguna Niguel, CA 92677 Phone: (949) 903-40336 (24-Hour) E-mail: EcoOilTreatment@gmail.com (Mr. William Azzalino) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (water based) 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: In case of eye contact, flush with water. In case of skin contact, wash with water. If swallowed, drink water to dilute and induce vomiting. 4.a. Maximum storage temperature: 60°C 4.b. Minimum storage temperature: 0°C 4.c. Optimum storage temperature range: 10°C to 30°C 4.d. Temperatures of phase separations and chemical changes: 85°C V. SHELF LIFE 2 years or more if stored correctly in plastic drums and at recommended temperatures. Surface Washing Agents 343 SOC 10 ------- VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Product may be applied by manual or mechanical means including but not limited to: hand operated spraying flask, spraying equipment and jet spraying equipment. Application mixture, once applied, should be washed with water or any suitable type for desired end result after about 3 minutes. Application mixture can be applied without further action or may be scrubbed, rubbed, or abraded as desired until diluted hydrocarbons have been removed from soil, sand, or rocks. 2. Concentration/Application Rate: Product should be applied at a 1:12 product to water ratio: 1:12(1 oz of SOC 10 concentrated: 11 oz water or 1 ml SOC 10 concentrated to 11 ml water). 3. Conditions for Use: Product may be used in fresh, river, brackish, or salt water of any temperature above 35°F. Optimum temperature for normal contamination is 25°C for heavy or aged oil. Product is suitable for use on crude oils and petroleum products that retain the majority of their VOCs including oil slicks, oil sheens, oil emulsions, and oil spills. It is not suitable for use on tar balls or other tar masses, or tar sands. For in-situ washing of sands, soils, and vegetation, a lined recovery trench may be built down slope to recover any residue. As washing occurs, pump residue from trench and dispose according to federal, state, and local regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) SOC 10 Menidia beryllina 20,007 96-hr Mysidopsis bahia 9,639 48-hr No. 2 Fuel Oil Menidia beryllina 3.76 96-hr Mysidopsis bahia 2.04 48-hr SOC 10 & Menidia beryllina 6.31 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.24 48-hr Reference Toxicant (SLS) Menidia beryllina 12.19 96-hr Mysidopsis bahia 10.53 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. FlashPoint: 122°F 2. Pour Point: 29°F 3. Viscosity: 1.261 cps @40°C 4. Specific Gravity: 0.9970 g/cc @60°F 5. pH: 7.3 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: None 9. Solubility: Completely water soluble Surface Washing Agents 344 SOC 10 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Concentration (ppm) Arsenic <0.050 Cadmium <0.035 Chromium <0.025 Copper <0.050 Lead <0.060 Mercury 0.0005 Nickel <0.050 Zinc 0.052 Cyanide <0.150 Chlorinated Hydrocarbons <1.0 Surface Washing Agents 345 SOC 10 ------- TECHNICAL PRODUCT BULLETIN #SW-46 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 17, 2010 "BIOGRASS EXTRA®" I. NAME, BRAND, OR TRADEMARK BIOGRASS EXTRA® Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Quimica del Desierto, S. De R.L. de C.V. Madrid 2001-A Col. Mirador Chihuahua City, Chihuahua, Mexico C.P. 31205 Phone: +52-1-614-110-2650 E-mail: erich.wolf@biograssextra.com Website: www.biograssextra.com (Ing. Erich Wolf) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS HRD Ecological Equations LLC 1417 Palma Plaza Austin, Texas, 78703 Phone: (512) 789-4881 E-mail: info@biograssextra.com (Mr. Howard Reed) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous). 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required; however goggles are recommended. In case of eye irritation, flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Mix well before use if outside the 60-85°F range. Surface Washing Agents 346 BIOGRASS EXTRA® ------- V. SHELF LIFE Two years minimum. VI. RECOMMENDED APPLICATION PROCEDURES Recommended application procedures depending on concentration of contaminants, water salinity levels, water temperature, and the type and age of the contaminant. There are two means of application: power spraying or direct application. a. Application via power spraying: Use of a power washer to spray the contaminated surface. The action may be improved by warming the product during use. b. Application via direct application: Remove contaminated soil, sand, etc. into a container. Irrigate the affected ground with the product and let it soak in. Agitate the mixture of water/product/ground and add additional water to float the contaminant off of the surface. A layer of product-contaminant will form which may be physically separated from the soil. The oil in this layer may be separated by dehydration or pumping to prepare the contaminant for disposal or reclamation. The clean soil or sand may be returned to its original environment. The residue should be removed and disposed of as required by local, state, or federal regulations. The on-site coordinator can determine the best way to recover the residue based on the spill type, surface, and environment of the area. Concentrations: The concentration of the BIOGRASS® EXTRA product to be used depends on the density of the contaminant. Normally the product is used in a one-to-one proportion with the contaminant. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested BIOGRASS® EXTRA No. 2 Fuel Oil BIOGRASS® EXTRA & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Species LC50 (DDm) Menidia beryllina 548.66 96-hr Mysidopsis bahia 703.43 48-hr Menidia beryllina 2.51 96-hr Mysidopsis bahia 2.24 48-hr Menidia beryllina 2.54 96-hr Mysidopsis bahia 2.24 48-hr Menidia beryllina 12.25 96-hr Mysidopsis bahia 11.71 48-hr Surface Washing Agents 347 BIOGRASS EXTRA® ------- IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: 21.0°F 3. Viscosity: 1.37 cSt @40°C 4. Specific Gravity: 1.0253 @60°F 5. pH: 7.1 6. Surface Active Agents: Anionic and nonionic, proprietary, surfactants 7. Solvents: Water 8. Additives: Sodium phosphate dibasic, sodium chloride 9. Solubility: Miscible in water and some solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.0702 Cadmium 0.0024 Chromium 0.0174 Copper 0.0158 Lead 0.0086 Mercury <0.001 Nickel 0.0580 Zinc 0.3092 Cyanide <0.010 Chlorinated Hydrocarbons <1.0 Surface Washing Agents 348 BIOGRASSEXTRA® ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-47 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 25, 2010 "ENVIRONMENTAL 1 CRUDE OIL CLEANER" I. NAME, BRAND, OR TRADEMARK ENVIRONMENTAL 1 CRUDE OIL CLEANER (aka, ENVIRONMENTAL 1 WASHING AGENT) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Environmental 1, LLC P.O. Box 9 Jackson, TN 38302 Phone: (615) 269-0506 Fax: (615)269-0025 E-mail: info@environmental-one.com E-mail: mfb@environmental-one.com Website: www.environmental-one.com (Ms. Mary Frances Blankenship, President) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Environmental 1, LLC P.O. Box 9 Jackson, TN 38302 Phone: (615) 269-0506 Fax: (615)269-0025 E-mail: info@environmental-one.com E-mail: mfb@environmental-one.com Website: www.environmental-one.com (Ms. Mary Frances Blankenship, President) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable, no hazards or restrictions 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required; however goggles are recommended if used with a pressure washer. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 140°F 4.b. Minimum storage temperature: 35°F 4/04/2016 7/27/2022 Surface Washing Agents 349 ENVIRONMENTAL 1 CRUDE OIL CLEANER ------- 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Unlimited in sealed polydrums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES ENVIRONMENTAL 1 CRUDE OIL CLEANER cleans oil from solid surfaces such as beaches, rocks, machines, buildings, tools, and other hard surfaces. 1. Spray ENVIRONMENTAL 1 CRUDE OIL CLEANER on oil surface to be cleaned with a drum pump sprayer or for smaller jobs use a hand pump sprayer. 2. On areas of heavy oil accumulation use product directly on the spill, or for areas of lighter accumulation use a 1:10 to 1:30 dilution ratio (product:water). 3. The oil and cleaner form a loose emulsion that can be rinsed away. Oil displaced from hard surfaces can be skimmed from the rinse water, absorbed with an oil absorbent, or removed via commercial waste removal. 4. May be used with fresh or salt water in normal climatic temperatures. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested ENVIRONMENTAL 1 CRUDE OIL CLEANER No. 2 Fuel Oil ENVIRONMENTAL 1 CRUDE OIL CLEANER & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: +26.0°F 3. Viscosity: 3.34 cSt @ 40°C 4. Specific Gravity: 1.01 @ 15°C 5. pH: 6.2 6. Surface Active Agents: Anionic, nonionic, zwitterionic surfactants 7. Solvents: None 8. Additives: Preservative Species LC50 (DDm) Menidia beryllina 22.68 96-hr Mysidopsis bahia 16.27 48-hr Menidia beryllina 2.24 96-hr Mysidopsis bahia 0.99 48-hr Menidia beryllina 2.19 96-hr Mysidopsis bahia 0.43 48-hr Menidia beryllina 12.25 96-hr Mysidopsis bahia 11.71 48-hr Surface Washing Agents 350 ENVIRONMENTAL 1 CRUDE OIL CLEANER ------- 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.0021 Cadmium <0.0010 Chromium <0.0030 Copper <0.0030 Lead <0.0020 Mercury <0.0005 Nickel <0.0050 Zinc <0.0030 Cyanide <0.010 Chlorinated Hydrocarbons <5.00 Surface Washing Agents 351 ENVIRONMENTAL 1 CRUDE OIL CLEANER ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-48 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: OCTOBER 4, 2010 "SANDKLENE 950" I. NAME, BRAND, OR TRADEMARK SANDKLENE 950 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT MDEChem, Inc. 923 10th Street PMB 101 Floresville, TX 78114 Phone: updated information required E-mail: updated information required Website: www.mdechem.com (Mr. Paul Sack) III. NAME, ADDRESS, AND Imperial Petroleum, Inc. 101 NW 1st Street #213 Evansville, IN 47708 Phone: (812)867-1433 E-mail: Jwilsonx 1 @aol.com (Mr. Jeff Wilson) Archer Petroleum Corp. 490-580 Hornby St. Vancouver, Canada V6C 3B6 604-683-7588 (Mr. Colin Bowkett) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Normal 3. Skin and eye contact; protective clothing; treatment in case of contact: Wear chemically impervious gloves. No other special equipment or clothing is required; however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 3/16/2016 7/27/2022 TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Mailing Address: Imperial Petroleum, Inc. P.O. Box 1006 Evansville, IN 47706 (Mr. Jeff Wilson) Surface Washing Agents 352 SANDKLENE 950 ------- 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Unlimited in sealed drums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: SANDKLENE 950 is most effective in enclosed systems using centrifuges, shearing devices, or similar high speed equipment to process material. Under these conditions, SANDKLENE 950 and water are recycled continuously. In smaller applications on solid surfaces, SANDKLENE 950 may be applied with sprayers using water diluted product directly onto solid oil coated surfaces. 2. Concentration/Application Rate: Oil contaminated sands are placed in an enclosed chamber with a solution of SANDKLENE 950 and water. The concentration of SANDKLENE 950 in water ranges from about 0.15% to about 1.0%. The total volume of solution is 350 gallons per 3 cubic yards of contaminated sand. The mixture is agitated at an elevated temperature in the range of 100°F to 150°F. The actual treatment rate will vary within the recommended range, depending upon the nature of sand, the nature of the oil, and the percentage of oil content. 3. Conditions for Use: The water and oil parts are separated from the sand. The water part is continuously recycled, the oil is recovered, and the sand can be disposed according to federal, state, and local regulations. Dose rates and SANDKLENE 950 concentrations will vary with the type and amount of petroleum present, the extent of weathering, and other site specific conditions, including temperature and time available to let the solution contact the oil. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (DDm) SANDKLENE 950 Menidia beryllina 1768.73 96-hr Mysidopsis bahia 1263.78 48-hr No. 2 Fuel Oil Menidia beryllina 8.95 96-hr Mysidopsis bahia 2.41 48-hr SANDKLENE 950& Menidia beryllina 4.48 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.24 48-hr Reference Toxicant (DLS) Menidia beryllina 12.25 96-hr Mysidopsis bahia 11.71 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: +10°F 3. Viscosity: 3.69 cSt @ 40°C Surface Washing Agents 353 SANDKLENE 950 ------- 4. Specific Gravity: 1.2806 @60°F 5. pH: 9.4 6. Surface Active Agents: None 7. Solvents: None 8. Additives: None 9. Solubility: Completely soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.540 Cadmium <0.209 Chromium 1.100 Copper <0.205 Lead <0.494 Mercury 0.0009 Nickel <0.274 Zinc <0.204 Cyanide <1.150 Chlorinated Hydrocarbons <0.100 Surface Washing Agents 354 SANDKLENE 950 ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-49 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 10, 2010 "DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE" I. NAME, BRAND, OR TRADEMARK DE-SOL V-IT CLEAN AWAY APC SUPER CONCENTRATE Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Orange-Sol Blending and Packaging 1400 N Fiesta Boulevard Gilbert, AZ 85233 Phone: (800) 877-7771 Fax: (480) 497-0444 E-mail: updated information required Website: www.orange-sol.com (Mr. Albert Farnsworth or Mr. Jack Farnsworth at (480) 319-0141) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Bell Tech Master Distributor P.O. Box 2198 Valdez, AK 99686 Phone: (907) 602-0111 Fax: (907) 835-4535 E-mail: bellenterprise@cvinternet.net (Mr. Randy Bell) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-combustible 2. Ventilation: No special requirements 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment of clothing required; however, goggles are recommended where splash is potential. If eye or skin irritation occurs, flush with ample fresh water. 4.a. Maximum storage temperature: 210°F 4.b. Minimum storage temperature: 34°F 4.c. Optimum storage temperature range: 55°F to 90°F 3/03/2016 7/27/2022 Surface Washing Agents 355 DE-SOL V-IT CLEAN AWAY APC SUPER CONCENTRATE ------- 4.d. Temperatures of phase separations and chemical changes: There are no known phase separations, chemical changes, or other altercations that will change the effectiveness of the product. V. SHELF LIFE Two (2) years in sealed drums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE can be used on all oil coated surfaces including sand and rocks through a detergency mechanism. Product should be used with handheld sprayers or for larger applications applied with truck mounted sprayers. Remove contamination with DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE, followed by a rinse. 2. Concentration/Application Rate: For oil spill removal and heavy duty cleaning, dilute product with water using a 1:1 ratio. 3. Conditions for Use: DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE can be used in salt or fresh water, with no limitations as to usage within the optimum temperature parameters (application may be made at or above 35°F, with optimum above 48°F). Cleaning of oil soaked areas should be done in a contained area and residue should be collected. For sand or vegetation cleaning, a berm may be constructed down slope that will collect the residue for disposal. All disposal residues should be done according to federal, state, and local regulations. In general, the technique used for collection of the oil/soap residue should be determined by the onsite contractor based on the environment of the area to be cleaned and the equipment and materials available for collection. Cleanup residue should be collected and disposed of in accordance with local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE No. 2 Fuel Oil DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 20.95 96-hr 30.95 48-hr 4.07 96-hr 0.86 48-hr 6.42 96-hr 0.69 48-hr 12.04 96-hr 8.19 48-hr b. Effectiveness: NA Surface Washing Agents 356 DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: +20°F 3. Viscosity: 3.1 cSt @ 40°C 4. Specific Gravity: 1.024 @60°F 5. pH: 9.03 6. Surface Active Agents: PROPRIETARY 7. Solvents: PROPRIETARY 8. Additives: Yes 9. Solubility: 100 percent X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <1.0 Cadmium <0.5 Chromium <0.5 Copper <2.0 Lead <1.0 Mercury <0.005 Nickel <1.0 Zinc <2.5 Cyanide 0.08 Chlorinated Hydrocarbons <0.05 Surface Washing Agents 357 DE-SOLV-IT CLEAN AWAY APC SUPER CONCENTRATE ------- LISTING CHANGES PENDING; VERIFICATION BY MANUFACTURER AND EPA REQUIRED TECHNICAL PRODUCT BULLETIN #SW-50 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: NOVEMBER 17, 2010 "EO ALL PURPOSE SOAP-LAVENDER" I. NAME, BRAND, OR TRADEMARK EO ALL PURPOSE SOAP-LAVENDER Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT EO Products/Small World Trading Company 90 Windward Way San Rafael, CA 94901 Phone: (415) 945-1900 Fax: (415)945-7117 E-mail: kimberly@eoproducts.com or sam@eoproducts.com Website: www.eoproducts.com (Ms. Kimberly Luce or Mr. Sam Borri) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS EO Products/Small World Trading Company 90 Windward Way San Rafael, CA 94901 Phone: (415) 945-1900 Fax:(415) 945-7117 E-mail: kimberly@eoproducts.com or sam@eoproducts.com Website: www.eoproducts.com (Ms. Kimberly Luce or Mr. Sam Borri) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Normal 3. Skin and eye contact; protective clothing; treatment in case of contact: Rinse thoroughly after use. Avoid eye contact. In case of such contact, immediately flush with large amounts of cool water for at least 15 minutes. Consult a physician if irritation develops. Protective gloves are recommended for extended or prolonged contact (e.g., immersing hands). Wear safety glasses if the method of use presents the likelihood of eye contact. Do not ingest. In case of ingestion, consult a physician. 4.a. Maximum storage temperature: 45°C Surface Washing Agents 358 EO ALL PURPOSE SOAP LAVENDER ------- 4.b. Minimum storage temperature: 4°C 4.c. Optimum storage temperature range: 22°C to 30°C 4.d. Temperatures of phase separations and chemical changes: Phase separation may occur at <15°C (but will restore to original condition at optimum temperature). V. SHELF LIFE Three (3) years (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: EO ALL PURPOSE SOAP may be applied by pouring, spraying (when diluted 1:4), dispensing equipment, or by scrubbing machines. 2. Concentration/Application Rate: Apply EO ALL PURPOSE SOAP full strength (undiluted) to surface area by pouring or with dispensing equipment concentrating on areas with heaviest contamination first. Apply diluted (1:4 dilution rate) EO ALL PURPOSE SOAP with sprayer. Agitate and scrub well. Rinse thoroughly. For heavily contaminated surfaces, EO ALL PURPOSE SOAP should always be used full strength (undiluted). For average to light contamination, EO ALL PURPOSE SOAP may be diluted from 2x-10x with water. 3. Conditions for Use: During cleaning, contain the oil soaked area and collect residue. For sand and vegetation cleaning, a berm may be constructed down slope that will collect the residue for disposal. All disposal of residue should be done according to federal, state, and local regulations. In general, the technique used for the collection of the oil/soap residue should be determined by the on-site contractor based on the environment of the area to be cleaned, and equipment and materials available for collection. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) EO ALL PURPOSE Menidia beryllina 21.33 96-hr SOAP Mysidopsis bahia 83.65 48-hr No. 2 Fuel Oil Menidia beryllina 8.95 96-hr Mysidopsis bahia 2.41 48-hr EO ALL PURPOSE Menidia beryllina 3.14 96-hr SOAP & No. 2 Fuel Oil Mysidopsis bahia 2.37 48-hr (1:10) Reference Toxicant Menidia beryllina 12.04 96-hr (SLS) Mysidopsis bahia 8.19 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C Surface Washing Agents 359 EO ALL PURPOSE SOAP LAVENDER ------- 2. Pour Point: +24°F 3. Viscosity: 349.5 cSt @ 40°C 4. Specific Gravity: 1.0208 @60°F 5. pH: 5.88 6. Surface Active Agents: PROPRIETARY 7. Solvents: PROPRIETARY 8. Additives: PROPRIETARY 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons CYANIDE, AND CHLORINATED Concentration (ppm) <0.540 <0.209 0.202 <0.205 <0.494 <0.000388 5.99 <0.204 <1.15 <2.0 Surface Washing Agents 360 EO ALL PURPOSE SOAP LAVENDER ------- TECHNICAL PRODUCT BULLETIN #SW-51 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: DECEMBER 7, 2010 "DYNAMIC GREEN™" I. NAME, BRAND, OR TRADEMARK DYNAMIC GREEN™ Type of Product: Surface Washing Agent (Water-based) II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Wechem, Inc. 5734 Susitna Drive Harahan, LA 70123 Phone: (800) 426-0512 Phone: (504) 733-1152 Fax:(504)733-2218 E-mail: mwisecarver@ wechem.com or lhernandez@wechem.com Website: www.wechem.com (Mr. Mike Wisecarver) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Wechem, Inc. 5734 Susitna Drive Harahan, LA 70123 Phone: (800) 426-0512 Phone: (504) 733-1152 Fax:(504)733-2218 E-mail: mwisecarver@wechem.com or lhernandez@wechem.com Website: www.wechem.com (Mr. Mike Wisecarver) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Not required. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wear protective gloves that are chemical resistant, rubber. In case of skin contact, wash with soap and water. If irritation develops seek medical attention. Wear safety glasses/goggles for eye protection. In case of eye contact flush with water for 15 minutes. If irritation develops seek medical attention. 4.a. Maximum storage temperature: 140°F 4.b. Minimum storage temperature: 34°F 4.c. Optimum storage temperature range: >50°F and <100°F 4.d. Temperatures of phase separations and chemical changes: <35°F and >100°F. Surface Washing Agents 361 DYNAMIC GREEN™ ------- V. SHELF LIFE DYNAMIC GREEN™ has a shelf life of 6-10 years in sealed poly drums or totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Product may be applied to any surface for removal of oils. The product can be applied through power washers, garden type sprayers, fire pump or any other portable pump with seawater or freshwater suction that is equipped with a chemical inductor or feed pump. For smaller areas properly diluted DYNAMIC GREEN™ may be applied with sponge, mop, scrub brush or cloth. Apply liberally, adjusting dilution on site if necessary. 2. Concentration/Application Rate: For heavily weathered oil on rocks, a diluted solution of 4 parts water to 1 part product is recommended. For heavily weathered oil on beaches/sand a diluted solution of 7 parts water to 1 part product is effective. For removing oil from vegetation, a diluted solution of 10/20 parts water to 1 part product is preferred. Product is effective in fresh or salt water. 3. Conditions for Use: Allow diluted product to soak for 20-30 minutes to soften and lift oil from surface. Reapplication may be necessary for severely contaminated areas. Vacuum suction equipment and sorbent boom or pads should be used to collect the washed effluent. When proper containment equipment is in place and a soak time of 20 minutes has been achieved, a diluted solution of 20 parts water to 1 part product should be applied through a pressure washer or flushing device to remove oils. Product and oil should be vacuumed up or absorbed with absorbent boom and disposed of according to EPA guidelines. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested DYNAMIC GREEN™ Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 106.00 96-hr 66.60 48-hr 13.00 96-hr 3.16 48-hr 6.85 96-hr 3.30 48-hr No. 2 Fuel Oil EO ALL PURPOSE SOAP & No. 2 Fuel Oil (1:10) Reference Toxicant Menidia beryllina Mysidopsis bahia 2.67 96-hr 9.14 48-hr (SDS) b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Surface Washing Agents 362 DYNAMIC GREEN™ ------- IX. PHYSICAL PROPERTIES 1. Flash Point: >200°F 2. Pour Point: -16°F 3. Viscosity: <10 cSt @ 78°F 4. Specific Gravity: 1.01 @77°F 5. pH: 7.5 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Infinitely miscible X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.25 Cadmium <0.25 Chromium <0.25 Copper <0.25 Lead <0.25 Mercury <2.00 Nickel <0.25 Zinc <0.25 Cyanide <0.50 Chlorinated Hydrocarbons ND Surface Washing Agents 363 DYNAMIC GREEN™ ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 8/29/2012 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-52 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: DECEMBER 9, 2010 "VERU-SOLVE™ MARINE 200 HP" I. NAME, BRAND, OR TRADEMARK VERU-SOLVE™ MARINE 200 HP Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT VeruTEK® Technologies 65 West Dudley Town Road, Suite 100 Bloomfield, CT 06002 Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Ms. Bethany McAvoy) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS VeruTEK® Technologies 65 West Dudley Town Road, Suite 100 Bloomfield, CT 06002 Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Ms. Bethany McAvoy) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Use in a well ventilated area. 3. Skin and eye contact; protective clothing; treatment in case of contact: Prevent eye contact, wear safety glasses or goggles. If eye contact occurs remove contact lenses at once. Flush with water for at least 15 minutes. If irritation persists seek medical attention. Prevent skin contact, nitrile gloves are recommended. Boots, aprons, or bodysuits should be worn as necessary. Contact with product may cause slight redness. Prolonged or repeated exposure may cause drying of skin. If skin contact occurs wash affected area with copious amounts of soap and water. Respiratory protection is not normally required. If adequate ventilation is unavailable use NIOSH approved air-purifying respirator with organic vapor cartridge or canister. The product is not likely toxic. If ingestion occurs DO NOT induce vomiting. Rinse mouth thoroughly with Surface Washing Agents 364 VERU-SOLVE™ MARINE 200 HP ------- water. Offer water to drink. DO NOT administer anything by mouth to an unconscious person. 4.a. Maximum storage temperature: Should not exceed 110°F (43.3°C) 4.b. Minimum storage temperature: Above 41°F (5°C) 4.c. Optimum storage temperature range: Between 41°F and 110°F (5°C to 43.3°C) 4.d. Temperatures of phase separations and chemical changes: Stable. There is no known temperature within the maximum and minimum storage temperature that would cause phase separation, chemical changes, or other known alterations to the effectiveness of the product. V. SHELF LIFE Indefinite, product will not degrade over time. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: VERU-SOLVE™ MARINE 200 HP is an aqueous based liquid without solids that can be readily applied through standard spray equipment. VERU-SOLVE™ MARINE 200 HP is suited for treating oil shorelines, sensitive environments, and for treating access limited areas. VERU-SOLVE™ MARINE 200 HP may be applied directly to oil on shoreline, beaches, rocks, or marsh surfaces by agricultural or standard sprayers attached to all terrain vehicles (ATVs), or workboats equipped with spray booms. The preferred and most effective method of application is to use a low-volume, low-pressure pump. 2. Concentration/Application Rate: The product can be applied undiluted to the spilled oil. VERU-SOLVE™ MARINE 200 HP should be applied as droplets, not fogged or atomized. System Calibration - Spray systems should be calibrated to insure accurate application rates for successful application and dosage control. 3. Conditions for Use: VERU-SOLVE™ MARINE 200 HP is sprayed directly on oil coated materials; and can be used on fresh or aged oil or oil combinations. Application may be limited at sub-freezing temperatures (<31 °F) without inclusion of antifreeze additives. VERU-SOLVE™ MARINE 200 HP can be applied at temperatures above freezing without notable changes in viscosity with increasing temperature. Application is not affected by increasing salinity. VERU- SOLVE™ MARINE 200 HP can be used at temperatures above freezing and at temperatures above 70°F. VERU-SOLVE™ MARINE 200 HP will separate the oil and water from the sand or soiled surface. Cleaning of oil soaked surfaces should be done in a contained area and residue should be collected. For sand or vegetation cleaning, a berm may be constructed down slope that will collect the residue for disposal. Oil that has separated from sand or vegetation may be recovered from the substrate and collected for disposal. All disposal of residue should be done in accordance with federal, state, and local regulations. In general, the technique used for the collection of the oil/product residue should be determined by the On-Scene Coordinator based on the environment of the area to be cleaned, equipment and materials available for collection, and disposal regulations. Surface Washing Agents 365 VERU-SOLVE™ MARINE 200 HP ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) VERU-SOLVE™ Menidia beryllina 418.32 96-hr MARINE 200 HP Mysidopsis bahia 76.98 48-hr No. 2 Fuel Oil Menidia beryllina 13.36 96-hr Mysidopsis bahia 1.94 48-hr VERU-SOLVE™ Menidia beryllina 10.67 96-hr MARINE 200 HP & No. Mysidopsis bahia 2.51 48-hr 2 Fuel Oil (1:10) Reference Toxicant Menidia beryllina 13.36 96-hr (SLS) Mysidopsis bahia 12.08 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: +18°F 3. Viscosity: 1.77391 cSt @ 40°C 4. Specific Gravity: 1.017 @60°F 5. pH: 7.01 6. Surface Active Agents: PROPRIETARY 7. Solvents: None 8. Additives: None 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons CYANIDE, AND CHLORINATED Concentration (ppm) 0.0025 <0.0010 0.0326 0.0093 <0.0020 0.00109 0.0077 0.0165 <0.010 <0.025 Surface Washing Agents 366 VERU-SOLVE™ MARINE 200 HP ------- TECHNICAL PRODUCT BULLETIN #SW-53 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JANUARY 26, 2011 "NATURAMA G3 A-5" I. NAME, BRAND, OR TRADEMARK NATURAMA G3 A-5 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Green Life Development, Inc. Merlin-Tao Ltd. 5112 W. Charleston Boulevard, Suite C 65 Yigal Alon Street POB 91 Las Vegas, NV 89146 Tel Aviv, Israel 67443 Mobile: (702) 355-5102 Phone: 972-3-562-8020 Fax: (702) 448-6977 Fax: 972-3-562-8021 E-mail: david@greenlifedevelopment.com E-mail: asaf@merlin-tao.com Website: www.greenlifedevelopment.com Website: www.merlin-tao.com (Mr. David A. Levy) (Mr. Asaf Yaari, CEO) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Green Life Development, Inc. 5112 W. Charleston Boulevard, Suite C Las Vegas, NV 89146 Mobile: (702)355-5102 Fax: (702) 448-6977 E-mail: david@greenlifedevelopment.com Website: www.greenlifedevelopment.com (Mr. David A. Levy) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing is required; however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE NATURAMA G3 A-5 has unlimited shelf life in sealed poly drums. Surface Washing Agents 367 NATURAMA G3 A-5 ------- VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Product may be applied by any method (e.g., drum pump, pressurized spray applicator, brush, or aqueous wash tank), depending on the surface; and type and viscosity of the oil/contamination to be treated. 2. Concentration/Application Rate: The dilution ratio depends on the amount and type of contamination to be removed. For light contamination areas a 1:6 dilution ratio (product to fresh/salt water) with a 2-3 minutes wait. For heavier/thick/burnt contamination, the exact ratio should be determined by the field coordinator but a general starting point of 20-25% should remove most contamination (grease, burnt oil, diesel, tar, etc.) after a contact time of 10-15 minutes before rinsing with water/steam. 3. Conditions for Use: Cleanup residue must be collected and should be disposed of in accordance with local, state, and federal regulations. Where possible, the product/oil mixture can be recovered and processed using an oil separator system or a stagnant tank. A circulating wash tank fitted with an oil separator or filter system extends the life of NATURAMA G3 A-5 by weeks, greatly impacting the waste reduction. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) NATURAMA G3 A-5 Menidia beryllina 577.68 96-hr Mysidopsis bahia 482.97 48-hr No. 2 Fuel Oil Menidia beryllina 2.39 96-hr Mysidopsis bahia 0.32 48-hr NATURAMA G3 A-5 & Menidia beryllina 3.68 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.24 48-hr Reference Toxicant (SLS) Menidia beryllina 12.25 96-hr Mysidopsis bahia 12.08 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >93°C 2. Pour Point: +28°F 3. Viscosity: 1.3628 cSt @ 40°C 4. Specific Gravity: 1.006 @60°F 5. pH: 8.39 6. Surface Active Agents: PROPRIETARY 7. Solvents: PROPRIETARY 8. Additives: None 9. Solubility: Miscible in oil, water, and solvents Surface Washing Agents 368 NATURAMA G3 A-5 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.0092 <0.002 0.0262 <0.006 0.0062 0.0005 <0.01 <0.0166 0.014 <26.30 Surface Washing Agents 369 NATURAMA G3 A-5 ------- TECHNICAL PRODUCT BULLETIN #SW-54 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: FEBRUARY 25, 2011 "SAFE KLEEN" I. NAME, BRAND, OR TRADEMARK SAFE KLEEN Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Anti Slip Solutions Ltd Beauchamp House 402/403 Stourpout Road Kidderminster, Worcestershire DY12 1AB, UK Phone: 44 (0) 345-222-5613 E-mail: info@safe-grip.co.uk (Mr. Dan Bayliss) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS V4 Distributing 507 West Bird Avenue Nampa, ID 83686 Phone: (208) 571-8596 E-mail: info@v4distributing.com (Mr. Todd Vitek) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO Non-flammable (DOT: Non-hazardous) 2. Ventilation: Provide adequate ventilation. 3. Skin and eye contact; protective clothing; treatment in case of contact: Chemical eye goggles should be worn. In case of contact with eyes, rinse immediately with plenty of clean water for at least 15 minutes and seek medical advice. PVC or rubber gloves are recommended. Use protective clothing. Remove contaminated clothing and wash with soap and water. 4.a. Maximum storage temperature: 130°F 4.b. Minimum storage temperature: 40°F 4.c. Optimum storage temperature range: >40°F to <130°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Five years if stored in tightly closed containers under dry conditions within temperature range. Surface Washing Agents 370 SAFE-KLEEN ------- VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: For general use apply the product by spray, brush, mop, or standard pressure washing equipment. 2. Concentration/Application Rate: SAFE KLEEN is a concentrated liquid that can be used either as supplied or diluted with hot or cold, fresh or salt water. For small spills dilute 1:3 (product to water) and apply as described. For larger spills prepare a solution of SAFE KLEEN diluted with 50 percent water and apply as described. Concentrations may be adjusted to take account of temperatures, types and age of oil/contaminant and other local site conditions. Surface contact time will also be dependent on temperature. For low temperatures and conditions of heavy contamination extend the contact time, where possible agitation of the product during application time will assist the efficiency of the cleaning. Thoroughly rinse with water. 3. Conditions for Use: Response personnel can determine the best method to collect residue, which can include, but is not limited to, oil skimmers, collecting booms, vacuum equipment, absorbent materials, and other appropriate containment and collecting mechanisms. The cleanup residue should be collected and disposed of in accordance with local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested Species LC50 (DDm) SAFE KLEEN Menidia beryllina 170.00 96-hr Mysidopsis bahia 258.00 48-hr No. 2 Fuel Oil Menidia beryllina 3.30 96-hr Mysidopsis bahia 6.20 48-hr SAFE KLEEN & Menidia beryllina 2.60 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 6.50 48-hr Reference Toxicant (SDS) Menidia beryllina 7.60 96-hr Mysidopsis bahia 16.90 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: NA; water-based product 2. Pour Point: NA; water-based product 3. Viscosity: 2.33 cSt @ 40°C 4. Specific Gravity: 1.060 @68°F 5. pH: 11.5-13.0 6. Surface Active Agents: PROPRIETARY 7. Solvents: None 8. Additives: PROPRIETARY 9. Solubility: Totally soluble Surface Washing Agents 371 SAFE-KLEEN ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) <0.31 <0.16 <0.16 <0.16 <0.16 <0.025 <0.16 <0.16 ND ND Surface Washing Agents 372 SAFE-KLEEN ------- TECHNICAL PRODUCT BULLETIN #SW-55 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: FEBRUARY 25, 2011 "CORIBA 700 SR" (aka, CORIBA 700 ER, CORIBA 700 OS) I. NAME, BRAND, OR TRADEMARK CORIBA 700 SR (aka, CORIBA 700 ER, CORIBA 700 OS) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Coriba Technologies, LLC 5708 Cadron Creek North Little Rock, AR 72116 Phone: (501) 834-2972 E-mail: ronrios@bellsouth.net (Mr. Harvey G. Cobb) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS MLU Services 573 Hawthorne Avenue Athens, GA 30606 Phone: (706) 569-7300 Fax: (706) 425-0300 (Mr. Billy Ulm) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal (contains ammonia) 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye contact due to possible mild eye irritation. In case of eye contact, flush eyes with water for at least 15 minutes. In the case of skin contact, flush with water for at least 15 minutes. If irritation occurs and persists, obtain medical attention. Protective clothing is not normally required. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 33°F 4.c. Optimum storage temperature range: 33°F - 100°F 4.d. Temperatures of phase separations and chemical changes: Does not separate. V. SHELF LIFE Two years unopened minimum. Surface Washing Agents 373 CORIBA 700 SR ------- VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: CORIBA 700 SR is covered by U.S. Patent #7678201 (issued on March 16, 2010). The process is designed to remove and recover oil from sand. The product does not react with or alter the oil. Contaminated sand is transferred into a standard sand washer filled with 700 SR. The product is an aqueous solution that, upon contact, reduces the interfacial tension between the oil and the sand. The oil no longer adheres to the sand and is free to float to the surface of the processor and is removed with an auger. The cleaned sand is dried in a centrifuge and the collected liquid is recycled back to the processor. The product has a high vapor pressure and evaporates from the sand leaving no residue or contamination. The separated oil is transferred to a conical vertical tower where it concentrates at the surface and is siphoned off to be used as a fuel or sent to a refinery for further processing. The process solution that collects in the conical tower is recycled back to the processor. The clean, dry sand can be disposed as appropriate. Any sand that collects in the bottom of the conical tower is sent back through the processor. The process can be set up on a beach, waste treatment facility or on a barge for treating sensitive areas like barrier islands. The process chemical is not designed to come into contact with any body of water. There process is not designed to treat contaminated water. The process does not consume the process chemical. Any chemical that remains after the sand has been cleaned can be returned to the manufacturer or sent to an appropriate waste treatment facility. 2. Concentration/Application Rate: CORIBA 700 SR is used at full strength. It is delivered in aqueous solution. The application rate is 200 gallons/ton of oil-contaminated sand. 3. Conditions for Use: CORIBA 700 SR can be applied to contaminated sand as long as the sand mixture is not frozen. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested CORIBA 700 SR No. 2 Fuel Oil CORIBA 700 SR & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 1470.00 96-hr 3810.00 48-hr 11.10 96-hr 3.29 48-hr 22.80 96-hr 3.58 48-hr 5.70 96-hr 9.04 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Surface Washing Agents 374 CORIBA 700 SR ------- IX. PHYSICAL PROPERTIES 1. Flash Point: 102°F 2. Pour Point: 200°F 3. Viscosity: 1.0 cps 4. Specific Gravity: 0.981 5. pH: 11.4 6. Surface Active Agents: None 7. Solvents: None 8. Additives: PROPRIETARY 9. Solubility: Miscible with water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.05 Cadmium <0.002 Chromium 0.031 Copper 0.25 Lead 0.02 Mercury <0.01 Nickel <0.01 Zinc 0.25 Cyanide <0.1 Chlorinated Hydrocarbons <0.1 Surface Washing Agents 375 CORIBA 700 SR ------- TECHNICAL PRODUCT BULLETIN #SW-56 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: FEBRUARY 25, 2011 "CORIBA 713 SR" (aka, CORIBA 713 ER, CORIBA 713 OS) I. NAME, BRAND, OR TRADEMARK CORIBA 713 SR (aka, CORIBA 713 ER, CORIBA 713 OS) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Coriba Technologies, LLC 5708 Cadron Creek North Little Rock, AR 72116 Phone: (501) 834-2972 E-mail: ronrios@bellsouth.net (Mr. Harvey G. Cobb) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS MLU Services 573 Hawthorne Avenue Athens, GA 30606 Phone: (706) 569-7300 Fax: (706) 425-0300 (Mr. Billy Ulm) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal (contains ammonia) 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid eye contact due to possible mild eye irritation. Use chemical safety goggles and/or full face shield where splashing is possible. In case of eye contact, flush eyes with water for at least 15 minutes. Wear impervious protective clothing, including boots, gloves, lab coat, apron or coveralls, as appropriate, to prevent skin contact. In the case of skin contact, flush with water for at least 15 minutes. If irritation occurs and persists, obtain medical attention. Protective clothing is not normally required. 4.a. Maximum storage temperature: 100°F 4.b. Minimum storage temperature: 33°F 4.c. Optimum storage temperature range: 33°F - 100°F 4.d. Temperatures of phase separations and chemical changes: Does not separate. Surface Washing Agents 376 CORIBA 713 SR ------- V. SHELF LIFE Two years unopened minimum. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: CORIBA 713 SR is covered by U.S. Patent #7678201 (issued on March 16, 2010). The process is designed to remove and recover oil from sand. The product does not react with or alter the oil. Contaminated sand is transferred into a standard sand washer filled with 713 SR. The product is an aqueous solution that, upon contact, reduces the interfacial tension between the oil and the sand. The oil no longer adheres to the sand and is free to float to the surface of the processor and is removed with an auger. The cleaned sand is dried in a centrifuge and the collected liquid is recycled back to the processor. The product has a high vapor pressure and evaporates from the sand leaving no residue or contamination. The separated oil is transferred to a conical vertical tower where it concentrates at the surface and is siphoned off to be used as a fuel or sent to a refinery for further processing. The process solution that collects in the conical tower is recycled back to the processor. The clean, dry sand can be disposed as appropriate. Any sand that collects in the bottom of the conical tower is sent back through the processor. The process can be set up on a beach, waste treatment facility or on a barge for treating sensitive areas like barrier islands. The process chemical is not designed to come into contact with any body of water. There process is not designed to treat contaminated water. The process does not consume the process chemical. Any chemical that remains after the sand has been cleaned can be returned to the manufacturer or sent to an appropriate waste treatment facility. 2. Concentration/Application Rate: CORIBA 713 SR is used at full strength. It is delivered in aqueous solution. The application rate is 200 gallons/ton of oil-contaminated sand. 3. Conditions for Use: CORIBA 713 SR can be applied to contaminated sand as long as the sand mixture is not frozen. The process is effective at ambient temperature. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested CORIBA 713 SR No. 2 Fuel Oil CORIBA 713 SR & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 1070.00 2350.00 11.10 3.29 9.55 4.04 5.70 9.04 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Surface Washing Agents 377 CORIBA 713 SR ------- IX. PHYSICAL PROPERTIES 1. Flash Point: 212°F 2. Pour Point: 220°F 3. Viscosity: 1.0 cps 4. Specific Gravity: 0.997 5. pH: 11.0 6. Surface Active Agents: None 7. Solvents: None 8. Additives: PROPRIETARY 9. Solubility: Miscible with water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.05 Cadmium <0.002 Chromium 0.031 Copper 0.25 Lead 0.02 Mercury <0.01 Nickel <0.01 Zinc 0.25 Cyanide <0.1 Chlorinated Hydrocarbons <0.1 Surface Washing Agents 378 CORIBA 713 SR ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 7/19/2021 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-57 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MAY 11, 2011 "JEP-MARINE CLEAN" (aka, ECOVOOM-MARINE) I. NAME, BRAND, OR TRADEMARK JEP-MARINE CLEAN (aka, ECOVOOM-MARINE) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Nuance Solutions* 900 E. 103rd Street, Suite D Chicago, IL 60628 Phone: (800) 621-8553 Fax:(800)621-1276 (Mr. Neil Houtsma) (*Nuance Solutions is the manufacturer for Jubilee Environmental Products, product owner) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Jubilee Environmental Products 406 S. Boulder, Suite 820 Tulsa, OK 74103 Phone: (918) 277-1113 Fax: (918) 296-3997 E-mail: iubilinc@aol.com Sales and Inquiries: Phone: (918) 277-1113 Fax: (918) 296-3997 E-mail: iubilinc@aol.com (Mr. Thomas J. Rhein, President) Restored Cleaner LLC 2475 Fairfield Avenue Bridgeport, CT 06605 Phone: (203) 335-9555 Fax:(203)335-9550 E-mail: info@restoredcleaner.com Sales and Inquiries: Phone: (203) 335-9555 Fax:(203)335-9550 E-mail: info@restoredcleaner.com (Mr. Col ton Amster) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Normal. 3. Skin and eye contact; protective clothing; treatment in case of contact: Respiratory protection not required under normal conditions. Protect against generated mists using protective clothing in order to minimize contact (i.e., boots, apron, face shield). Use safety glasses/goggles during handling and application to prevent eye contact. Wear rubber/PVC gloves to prevent skin Surface Washing Agents 379 JEP-MARINE CLEAN ------- contact. 4.a. Maximum storage temperature: 90°F 4.b. Minimum storage temperature: 40°F 4.c. Optimum storage temperature range: 40 - 90°F; product freezes at 32°F 4.d. Temperatures of phase separations and chemical changes: 120°F V. SHELF LIFE In unopened containers, shelf life is minimum 2 years. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Product may be diluted with fresh or salt water, and may be applied to any type of surfaces that have been coated with oil or other petroleum-based substances resulting from a spill (e.g., beaches, rocks). Manual pump sprayers should be used to presoak the contaminated areas, and pressure washers should be used to agitate the contaminated areas after a presoak has been applied. 2. Concentration/Application Rate: Shoreline Cleaning - presoak the surface needing to be cleaned, using a manual pump sprayer, with a dilution rate of one (1) part to three (3) parts water for approximately 10 to 15 minutes, without letting the product dry or evaporate. After the contaminated areas have been presoaking for the allotted time, run a dilution rate of one (1) part product to fifteen (15) parts water, through a pressure washer directly onto the contaminant. 3. Conditions for Use: Option temperature range for use is 45 to 212°F. When the contaminants have been released, they can be removed using sorbent pads, suction booms or skimmers, and hauled away and disposed of according to local, state, and federal law. It is recommended that for older or crustier contaminants higher pressure and stronger dilutions be used. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested JEP-MARINE CLEAN No. 2 Fuel Oil JEP-MARINE CLEAN & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 88.40 96-hr 153.90 2.70 1.63 3.58 2.32 8.84 14.90 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >100°C Surface Washing Agents 380 JEP-MARINE CLEAN ------- 2. Pour Point: -14°C 3. Viscosity: 1.1 cSt 4. Specific Gravity: 1.041 5. pH: 11.2 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: Water 8. Additives: CONFIDENTIAL 9. Solubility: Miscible with water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.004 Cadmium 0.084 Chromium 0.082 Copper 0.138 Lead <0.025 Mercury <0.0012 Nickel <0.025 Zinc 0.219 Cyanide 0.01 Chlorinated Hydrocarbons <0.01 Surface Washing Agents 381 JEP-MARINE CLEAN ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 9/27/2012 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-58 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JUNE 28, 2011 "ETHOS CLEAN" I. NAME, BRAND, OR TRADEMARK ETHOS CLEAN Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT MAG7 Venture Group, LLC, DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Mr. Greg Goodell or Mr. Trevor Quig) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS MAG7 Venture Group, LLC, DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Mr. Greg Goodell or Mr. Trevor Quig) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Move subject to fresh air. If breathing is difficult, obtain medical help. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wash affected skin area with water. Consult physician of irritation persists. Skin irritation will not occur with most users. Flush eyes with a large amount of water for at least 15 minutes. Consult physician if irritation persists. Wear safety glasses and neoprene or rubber gloves during application. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: NA. Phase separation will not Surface Washing Agents 382 ETHOS CLEAN ------- occur within the storage range. Product should be stored out of direct sunlight unless it is in an Ultraviolet (UV) light resistant container. V. SHELF LIFE 2 years in a sealed (unopened) container (tote, drum, pail) as delivered. 1 year in an opened container). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Apply ETHOS CLEAN to oil or contaminant with sprayer, pressure washer, mop, sponge, brush, or rags. Application times will depend on the level of contaminant with a minimum of 30 minutes recommended soak time. The required soak time to remove oil will vary with oil density and degree of weathering. ETHOS CLEAN separates the oil from the physical surface to allow the oil to be sprayed off with a water rinse. ETHOS CLEAN should be mixed into soil applications to increase the effectiveness and reduce the application time. 2. Concentration/Application Rate: Pure concentrate can be used for heavy contamination. Dilution ratios for most applications range from 2 to 1 (parts water to parts ETHOS CLEAN) to 10 to 1 (parts water to parts ETHOS CLEAN). Dilution ratios are dependent on the contamination level and application with heavier crude oil spills requiring a lower dilution ratio. Dilutions up to 50 to 1 (parts water to parts ETHOS CLEAN) can be used for lighter contaminations and cleaning. Rinse with water after usage for residue free surface. Surface cleaning typically requires 5 to 1 or 10 to 1 dilution ratio. These dilution ratios will require 1 gallon of ETHOS CLEAN per 250 square feet of surface area. These dilution ratios can be used in many applications including shorelines, rocks, and beaches. 3. Conditions for Use: Salt or fresh water (temperature ranges from 35°F to 120°F). Oil or contaminant can be skimmed from the water or rinsed and captured into collection containers and disposed of per local, state, and federal regulations. Dilution Intended Use 2:1 Heavy contamination such as oil spills 5:1 Direct application to heavily soiled areas VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested ETHOS CLEAN No. 2 Fuel Oil ETHOS CLEAN & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 3960.00 96-hr 4510.00 48-hr 26.30 96-hr 4.86 48-hr 25.00 96-hr 5.00 48-hr 2.23 96-hr 7.93 48-hr b. Effectiveness: NA Surface Washing Agents 383 ETHOS CLEAN ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 142°F 2. Pour Point: 30°F 3. Viscosity: 32 SUS @60°F 4. Specific Gravity: 1.1664 @60°F 5. pH: 11.6 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Complete in water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium 0.0813 Chromium 0.240 Copper 0.201 Lead 14.5 Mercury 5.0 (ppb) Nickel 2.12 Zinc ND Cyanide ND Chlorinated Hydrocarbons ND Surface Washing Agents 384 ETHOS CLEAN ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 9/27/2012 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-59 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JUNE 28, 2011 "OSR-10" I. NAME, BRAND, OR TRADEMARK OSR-10 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT MAG7 Venture Group, LLC, DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Mr. Greg Goodell or Mr. Trevor Quig) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS MAG7 Venture Group, LLC, DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: updated information required Fax: updated information required E-mail: updated information required Website: updated information required (Mr. Greg Goodell or Mr. Trevor Quig) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Move subject to fresh air. If breathing is difficult, obtain medical help. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wash affected skin area with water. Consult physician of irritation persists. Skin irritation will not occur with most users. Flush eyes with a large amount of water for at least 15 minutes. Consult physician if irritation persists. Wear safety glasses and neoprene or rubber gloves during application. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: NA. Phase separation will not Surface Washing Agents 385 OSR-10 ------- occur within the storage range. Product should be stored out of direct sunlight unless it is in an Ultraviolet (UV) light resistant container. V. SHELF LIFE 2 years in a sealed (unopened) container (tote, drum, pail) as delivered. 1 year in an opened container). VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Apply OSR-IO to oil or contaminant with sprayer, pressure washer, mop, sponge, or brush. Application times will depend on the level of contaminant with a minimum of 10 minutes recommended soak time. The required soak time to remove oil will vary with oil density and degree of weathering. OSR-IO separates the oil from the physical surface to allow the oil to be sprayed off with a water rinse. OSR-IO should be mixed into soil applications and agitated to increase the effectiveness and reduce the application time. 2. Concentration/Application Rate: Dilution ratios for most applications range from 2 to 1 (parts water to parts OSR-IO) to 15 to 1 (parts water to parts OSR-IO). Dilution ratios are dependent on the contamination level and application with heavier crude oil spills requiring a lower dilution ratio. Rinse with water after usage for residue free surface. Surface cleaning typically requires 5 to 1 or 10 to 1 dilution ratio. These dilution ratios will require 1 gallon of OSR-IO per 300 square feet of surface area. These dilution ratios can be used in many applications including shorelines, rocks, and beaches. 3. Conditions for Use: Salt or fresh water (temperature ranges from 35°F to 120°F). Oil or contaminant can be skimmed from the water or rinsed and captured into collection containers and disposed of per local, state, and federal regulations. Dilution Intended Use 2:1 Heavy/severe contamination such as oil spills 5:1 to 10:1 Moderate contamination 15:1 to 30:1 Light contamination VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested Species LC50 (ppm) OSR-10 Menidia beryllina 385.00 96-hr Mysidopsis bahia 399.00 48-hr No. 2 Fuel Oil Menidia beryllina 26.30 96-hr Mysidopsis bahia 4.86 48-hr OSR-10 & Menidia beryllina 16.00 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 4.77 48-hr Reference Toxicant (SDS) Menidia beryllina 2.23 96-hr Mysidopsis bahia 7.93 48-hr b. Effectiveness: NA Surface Washing Agents 386 OSR-10 ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: 143°F 2. Pour Point: 20°F 3. Viscosity: 37 SUS @60°F 4. Specific Gravity: 1.1672 @60°F 5. pH: 11.5 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Complete in water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium 0.209 Copper 0.150 Lead 7.57 Mercury 6.8 (ppb) Nickel 1.20 Zinc ND Cyanide ND Chlorinated Hydrocarbons ND Surface Washing Agents 387 OSR-10 ------- TECHNICAL PRODUCT BULLETIN #SW-60 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 13, 2011 "ACCELL CLEAN® SWA" I. NAME, BRAND, OR TRADEMARK ACCELL CLEAN® SWA Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Advanced BioCatalytics Corporation 18010 Skypark Circle, #130 Irvine, California 92614-6456 Office Phone: (949) 771-0209 General E-mail: info@abiocat.com Website: www.abiocat.com Product Management: Mobile: (949) 981-6510 E-mail: cpodella@abiocat.com (Mr. Carl Podella) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Advanced BioCatalytics Corporation 18010 Skypark Circle, #130 Irvine, California 92614-6456 Office Phone: (949) 771-0209 General E-mail: info@abiocat.com Website: www.abiocat.com Product Management: Mobile: (949) 981-6510 E-mail: cpodella@abiocat.com (Mr. Carl Podella) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Use in well-ventilated area. 3. Skin and eye contact; protective clothing; treatment in case of contact: Protective clothing is recommended. Avoid eye contact. In case of eye contact, immediately flush with large amounts of water for at least 15 minutes. Get prompt medical attention. Avoid direct contact with skin and clothing. In case of skin contact, immediately flush with large amounts of water. Remove contaminated clothing, including shoes, after flushing has begun. If irritation persists, seek medical attention. For open systems were contact is likely, wear long sleeve shirt, chemical resistant gloves, and protective chemical goggles. Surface Washing Agents 388 ACCELL CLEAN® SWA ------- 4.a. Maximum storage temperature: 130°F/55°C 4.b. Minimum storage temperature: 30°F/-1°C 4.c. Optimum storage temperature range: 40°F to 100°F/4°C to 38°C 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE The shelf life of unopened drums of ACCELL CLEAN® SWA is unlimited. Containers should always remain capped when not in use to prevent contamination and evaporation. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Spray ACCELL CLEAN® SWA onto oil-contaminated shorelines, mangroves, or seagrasses full strength as applied. Allow to soak for 15-30 minutes. Rocks may be scrubbed with a stiff bristle brush where appropriate. Rinse with fresh or salt water as appropriate. For weathered crude oil on sand, transfer oil-contaminated sand to sand washing equipment. Agitate sand/ACCELL CLEAN® SWA solution. ACCELL CLEAN® SWA will lift the oil from the sand due to its low interfacial tension. Remove water from sand by centrifuge. 2. Concentration/Application Rate: Recommended application rate is 1 gallon per 100 square feet, dependent on the amount of oil and the degree of weathering. For weathered crude oil from sand, prepare a cleaning solution of 0.25%-2.0% ACCELL CLEAN® SWA using fresh or salt water. 3. Conditions for Use: Collect the oil/product residue from the water's surface using skimmers, absorbent pads, or other conventional means. Dispose of used, clean up residue in accordance with local, state, and federal regulations. Dispose of clean sand as appropriate and ACCELL CLEAN® SWA solution can be recycled after centrifuge. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested Species LC50 (ppm) ACCELL CLEAN® SWA Menidia beryllina 24.12 96-hr Mysidopsis bahia 59.46 48-hr No. 2 Fuel Oil Menidia beryllina 17.13 96-hr Mysidopsis bahia 2.92 48-hr ACCELL CLEAN® SWA & Menidia beryllina 12.25 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.25 48-hr Reference Toxicant (DDS) Menidia beryllina 10.00 96-hr Mysidopsis bahia 29.00 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >180°F/82°C Surface Washing Agents 389 ACCELL CLEAN® SWA ------- 2. Pour Point: 10°F/-12°C 3. Viscosity: 68 SUS @60°F 4. Specific Gravity: 1.0141 @60°F 5. pH: 8.12 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Soluble in fresh or seawater X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <1.00 Cadmium <0.50 Chromium <1.00 Copper <2.50 Lead <1.00 Mercury <0.020 Nickel <4.00 Zinc <6.00 Cyanide <1.00 Chlorinated Hydrocarbons ND Surface Washing Agents 390 ACCELL CLEAN® SWA ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: 10/19/2016 7/27/2022 TECHNICAL PRODUCT BULLETIN #SW-61 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: OCTOBER 13, 2011 "EPA OIL FIELD SOLUTION™" (aka, HYDRO-CLEAN™, GLOBAL ENVIRONMENTAL CLEANER™, AW AN PRA OIL FIELD SOLUTION™) I. NAME, BRAND, OR TRADEMARK EPA OIL FIELD SOLUTION™ (aka, HYDRO-CLEAN™, GLOBAL ENVIRONMENTAL CLEANER™, AW AN PRA OIL FIELD SOLUTION™) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Environmental Protection Associates, Inc. 2578 Enterprise Road, Suite 141 Orange City, FL 32763 Phone: updated information required E-mail: updated information required Website: updated information required (Mr. Nathan Hall) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS International Green Building Group, Inc. AW AN International General Trading 10800 Main Street, Suite 150 P.O. Box 75352 Fairfax, VA 22030 Kingdom of Bahrain Phone: (202) 300-8324 Phone: 973-173-111-28 E-mail: info@internationalgreenbuildinggroup.com Fax: 973-172-950-05 Website: updated information required E-mail: iames@awanpra.com Website: www.awangroups.com Website: updated information required (Mr. James Gard) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required; however goggles are recommended. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F Surface Washing Agents 391 EPA OIL FIELD SOLUTION™ ------- 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE Unlimited in sealed polydrums or totes (as delivered). Avoid direct sunlight. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: Product may be applied to surfaces for removal of oils. Select proper dilution depending on material surface prior to application. For treatment of large areas, properly diluted product may be applied by spraying with a pressure washer, portable fire pump, or any other suitable pump with seawater or freshwater suction that is equipped with a chemical inductor or feed pump. For smaller areas, properly diluted product may be applied with scrubber, mop, cloth or damp sponge. Apply liberally, adjusting dilution on site as necessary. For shorelines, mangroves, and seagrasses product is sprayed directly on the oiled rocky surfaces full strength as supplied. After a soak time of zero to 30 minutes, the cleaner and oil released from the shoreline surface can be collected and disposed. The soak time may vary with temperature, oil density, and degree of weathering. 2. Concentration/Application Rate: For heavily weathered oil on rocks, a diluted solution of 3 parts water to 1 part product is recommended. For heavily weathered oil on beaches/sand, a diluted solution of 5 parts water to 1 part product is ideal. For removing oil from vegetation, a diluted solution of 10-20 parts water to 1 part product is preferred. Product may be diluted with either salt or fresh water. Warmer water (greater than 78°F) and/or good agitation during application will require less of the product. 3. Conditions for Use: Best results are obtained by allowing diluted solution to soak for at least 30 minutes to soften the oil deposits. Reapplication may be necessary in severely contaminated areas. A sorbent boom or vacuum suction equipment should be positioned to collect the washed off effluent. When proper containment equipment is in place and a soaking period of at least 30 minutes has been achieved, a diluted solution of 20 parts water and 1 part product should be applied at mid-pressure (approximately 100 PSI). Adjust pressure and angle of the hose sprayer to achieve optimum results, adjusting the dilution as necessary on site. Product and effluent should be vacuumed up or absorbed in absorbent boom and disposed of according to local, state, and federal regulations. EPA Oil Field Solution™ is useful on shorelines using fresh or salt water. It can be used on all types of oil including heavily weathered and emulsified ("chocolate mousse") containing up to 50 percent water. Surface Washing Agents 392 EPA OIL FIELD SOLUTION™ ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested EPA OIL FIELD SOLUTION™ No. 2 Fuel Oil EPA OIL FIELD SOLUTION™ & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 113.76 96-hr 114.60 3.00 1.41 2.94 1.12 12.25 12.06 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >95°F 2. Pour Point: -2°F 3. Viscosity: 1.137368 SUS @40°F 4. Specific Gravity: 1.11 @60°F 5. pH: 13.4 6. Surface Active Agents: Nonionic, proprietary, surfactants 7. Solvents: Proprietary 8. Additives: None 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.200 Cadmium <0.0600 Chromium <0.300 Copper <0.300 Lead <0.200 Mercury <1.00 (ug/1) Nickel <0.500 Zinc 2.31 Cyanide <0.0100 Chlorinated Hydrocarbons <250 (ug/1) Surface Washing Agents 393 EPA OIL FIELD SOLUTION™ ------- TECHNICAL PRODUCT BULLETIN #SW-62 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MARCH 5, 2012 "PETROMAX PSC 3" (aka, PETROMAX SOIL CLEANING AND WASHING AGENT) I. NAME, BRAND, OR TRADEMARK PETROMAX PSC 3 (aka, PETROMAX SOIL CLEANING AND WASHING AGENT) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Alfaluz S.A. Potosi 1517 Carrasco, Montevideo Uruguay Phone: 598-2-604-1006 Unites States: (305) 600-4927 Fax: (508)256-8318 E-mail: svonbergen@alfaluz.net Website: www.alfaluz.net (Mr. Scot von Bergen) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Alfaluz Inc. 1875 Post Oak Park Drive, Suite 523 Houston, Texas 77027 Phone: (832) 272-1816 Fax: (508) 256-8138 E-mail: mvonbergen@alfaluz.net (Mrs. Marina von Bergen) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required; however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable Surface Washing Agents 394 PETROMAX PSC 3 ------- V. SHELF LIFE Unlimited when stored in unopened, sealed 5 gallon containers, 55 gallon drums, poly drums, and totes. VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: PETROMAX PSC 3's mechanism of action is to reverse the charge of the particles (sand) holding the hydrocarbons, in such a way that the hydrocarbons and the particles reject each other thus allowing the hydrocarbons to be easily separated, removed, and collected. This is because the separated hydrocarbons maintain their globular integrity and are not dispersed nor solubilized into the water column. PETROMAX PSC 3 is applied via hydroblaster directly to the contaminated sand/soil and as it becomes fluidized it is sucked through a four inch hose into a mobile containment tank set up for the purpose at the job site. The contaminated material is cleaned through a three phase separation process: a) Solids Recovery: Once in the containment tank, the cleaned sand and soil particles precipitate immediately to the bottom, from which they are extracted via a slew-valve to secondary containment. Any entrained water within this containment is further recovered for reuse according to local, state, and federal regulations. b) Oil Recovery: During this process the hydrocarbons float to the surface of the tank and are removed by skimming. These removed hydrocarbons are collected and are sent to a refinery for processing. c) PETROMAX PSC 3/Water Recovery: This leaves only the used PETROMAX PSC 3/water solution in the tank, which can be reused or disposed of according to local, state, and federal regulations. The remaining water may contain some light particles in suspension. These particles are easily precipitated into cake residues which are then collected. The cake residues typically contain a water content below 10%. They can be dried in open air pits with plastic protection underneath or in 15 yard roll-off containers. Any contaminated water should be collected and sent to a standard water treatment facility. 2. Concentration/Application Rate: PETROMAX PSC 3 should be applied via hydroblaster lance with minimum 3200 psi pressure and 4-15 gallons per minute flow depending on material to be treated. For smaller spills, a smaller hydroblaster sprayer may be used, mixing fresh or salt water according to availability, and depending on the oil composition and viscosity in the contaminated sand and soil being treated. For large scale soil remediation and cleaning or soils and sands contaminated with heavy crude, direct PETROMAX PSC 3 directly on the spill (contaminated) material using a hydroblaster lance at a minimum pressure of 3500 psi, with a dilution ratio of approximately 1:10 (product:water). Lighter oil soil contamination will require a 1:20 to 1:30 product to water dilution ratio with pressures at 2800 psi minimum. Warmer water (greater than 70°F) may require less PETROMAX PSC 3. 3. Conditions for Use: A sorbent boom should be positioned during use to contain any runoff and the collected material should be disposed of according to local, state, and federal regulations. Surface Washing Agents 395 PETROMAX PSC 3 ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested PETROMAX PSC 3 No. 2 Fuel Oil PETROMAX PSC 3 & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 20332.19 96-hr 13460.87 1.90 1.68 1.99 1.00 12.25 12.35 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >185°F 2. Pour Point: +22°F 3. Viscosity: 1.5 est @40°C 4. Specific Gravity: 1.08 @60°F 5. pH: 13.23 6. Surface Active Agents: Anionic, proprietary 7. Solvents: None 8. Additives: Proprietary 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.121 Cadmium 0.332 Chromium 0.067 Copper <0.100 Lead 0.197 Mercury <0.50 (ug/1) Nickel <0.100 Zinc <0.100 Cyanide <0.010 Chlorinated Hydrocarbons <5.00 (ug/1) Surface Washing Agents 396 PETROMAX PSC 3 ------- TECHNICAL PRODUCT BULLETIN #SW-63 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 12, 2012 "GREEN TECHNOLOGIES SOLUTIONS-OIL RECOVERY (GTS-OR)" I. NAME, BRAND, OR TRADEMARK GREEN TECHNOLOGIES SOLUTIONS-OIL RECOVERY (GTS-OR) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT International Technologies and Services, Inc. 29258 Palos Verdes Drive East Rancho Palos Verdes, CA 90275 Phone: (310) 749-4487 E-mail: pilarladvbug@itsenvironmental.com Website: www.ITSEnvironmental.com (Ms. Pilar Ortega) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS International Technologies and Services, Inc. 29258 Palos Verdes Drive East Rancho Palos Verdes, CA 90275 Phone: (310) 749-4487 E-mail: pilarladybug@itsenvironmental.com Website: www.ITSEnvironmental.com (Ms. Pilar Ortega) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Handle in well ventilated space. 3. Skin and eye contact; protective clothing; treatment in case of contact: Product may cause minor irritation, so avoid eye and skin contact by wearing protective goggles, impermeable protective gloves, and protective clothing while handling the product. Wash contaminated clothing with soap and water, and dry prior to reuse. In case of contact, flush with large amounts of water for at least 15 minutes. Product may harmful if inhaled. In case of inhalation, move affected person to fresh air, and call a physician. Product may be harmful if swallowed. In case of ingestion, induce vomiting, give water, and call a physician. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 30°F 4.c. Optimum storage temperature range: >50°F to <100°F 4.d. Temperatures of phase separations and chemical changes: None V. SHELF LIFE One year minimum when stored between 50°F and 100°F. Surface Washing Agents 397 GREEN TECHNOLOGIES SOLUTIONS- OIL RECOVERY (GTS-OR) ------- VI. RECOMMENDED APPLICATION PROCEDURES 1. Application Method: GTS-OR may clean oil from beaches, rocks, riprap, pilings, and seawalls. GTS-OR application method can be adjusted depending on the scale and type of area to be cleaned. For large areas, GTS-OR can be sprayed from water trucks or water boats equipped with pumps, hoses, and nozzles to deliver the product as an aerial spray. The pump should be equipped with a chemical inductor or feed pump. In smaller applications, GTS-OR can be applied directly onto oiled surfaces using a pressure washer, steam powered unit, fire hose, or chemical boom sprayer with nozzles at mid-pressure (i.e., approximately 100 PSI) that produce a shearing action. For small applications, the product may be applied with mops, cloth, or damp sponges. For application in tidally influenced areas and to maximize contact time, GTS-OR should be applied during ebb tide (i.e., receding). Oil trapped between rocks or in crevices may be released over several days, requiring containment devises to be left in place. 2. Concentration/Application Rate: For heavily weathered oil on rocks, a diluted solution of 15 parts water to 1 part product is recommended. For heavily weathered oil on beaches/sand, a diluted solution of 10 parts water to 1 part product is ideal. For lightly-to-moderately oiled shorelines, mangroves, and seagrasses, the product should be sprayed directly to the affected surface at a 1:20 dilution ratio; a 1:10 dilution ratio is preferred for heavily oiled areas. 3. Conditions for Use: GTS-OR may be used in freshwater, estuarine, and marine environments. In all applications, the product may be diluted with either salt or fresh water, and the mixture should be allowed to penetrate and dissolve weathered petroleum for at least 30 minutes. Cold weather applications will require more contact time. Reapplication may be necessary for heavily oiled areas. The product may be used on both lighter oils (e.g., No. 2 Fuel Oil) and heavy ends (e.g., crude oil, No. 6 Fuel Oil). Prior to application, booms, oil skimmers, or other appropriate containment and collection mechanism should be deployed and operational. Collected product and oil mixture should be disposed of according to local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Materials Tested Species LC50 (ppm) GTS-OR Menidia beryllina 3930 96-hr Mysidopsis bahia 916 48-hr No. 2 Fuel Oil Menidia beryllina 8.16 96-hr Mysidopsis bahia 4.47 48-hr GTS-OR & Menidia beryllina 5.77 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.18 48-hr Reference Toxicant (SDS) Menidia beryllina 1.24 96-hr Mysidopsis bahia 4.77 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA Surface Washing Agents 398 GREEN TECHNOLOGIES SOLUTIONS- OIL RECOVERY (GTS-OR) ------- IX. PHYSICAL PROPERTIES 1. FlashPoint: 171°F 2. Pour Point: 35°F 3. Viscosity: 8.5 cSt @40°C 4. Specific Gravity: 1.009 @60°F 5. pH: 9.0 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility: Soluble in water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Concentration (ppm) 0.0084 <0.004 0.00064 0.180 0.00025 <0.00010 0.0012 0.017 <0.200 <2.5 Surface Washing Agents 399 GREEN TECHNOLOGIES SOLUTIONS- OIL RECOVERY (GTS-OR) ------- TECHNICAL PRODUCT BULLETIN #SW-64 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JULY 9, 2013 "SIMPLE GREEN® 2013 Reformulation" I. NAME, BRAND, OR TRADEMARK SIMPLE GREEN® 2013 REFORMULATION Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Sunshine Makers, Inc. 15922 Pacific Coast Highway Huntington Beach, CA 92649 Phone: (800) 228-0709 Phone: (562) 795-6000 Fax: (562) 592-3830 E-mail: LLorincz@simplegreen.com (Ms. Laura Lorincz) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Sunshine Makers, Inc. 15922 Pacific Coast Highway Huntington Beach, CA 92649 Phone: (800) 228-0709 Phone: (562) 795-6000 Fax: (562) 592-3830 E-mail: LLorincz@simplegreen.com (Ms. Laura Lorincz) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Not expected to cause respiratory irritation. However, use in well ventilated areas. If adverse effect occurs, move to fresh air. 3. Skin and eye contact; protective clothing; treatment in case of contact: Not expected to cause eye irritation. However, use protective glasses if splashing or spray-back is likely. If adverse effect occurs, flush eyes with water. Not expected to cause skin irritation. However, dermally sensitive users may experience dry skin and should use protective gloves. If adverse effect occurs, rinse skin with water. General hygiene considerations include washing hands thoroughly after handling and before eating or drinking. Ensure adequate ventilation. Keep out of reach of children. If ingested, drink plenty of water to dilute. 4.a. Maximum storage temperature: 109°F 4.b. Minimum storage temperature: 41°F Surface Washing Agents 400 SIMPLE GREEN® 2013 REFORMULATION ------- 4.c. Optimum storage temperature range: 42°F to 108°F 4.d. Temperatures of phase separations and chemical changes: SIMPLE GREEN® is stable and phase separation will not occur at temperatures within the maximum and minimum storage temperatures. If separation occurs, mix the product for reconstitution. V. SHELF LIFE SIMPLE GREEN® has a 5-year shelf life. Keep away from heat, sparks, open flame and direct sunlight. Do not pierce any part of the container. Keep container tightly closed. Keep in a cool dry area. Avoid prolonged exposure to direct sunlight. Do not store at temperatures above 109°F (42.7°C). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Spray or apply on oily surfaces (e.g., beaches, rocks, shorelines, pilings, etc.). 2. Concentration/Application Rate: a) Mix SIMPLE GREEN® in clean water at recommended concentration for strength of surface being cleaned: Degree that Surface is Covered in Oil Concentration of Simple Green® HEAVY - fresh, thick, viscous oil; porous surfaces Full strength to 25% MEDIUM - weathered, thinner coats of oil; non- 25% to 10% porous surfaces - use pressure washer equipment LIGHT - very light oil film; non-porous surfaces Less than 10% b) Apply SIMPLE GREEN® or diluted solution of Simple Green® to oiled surface via sponge, mop, coarse spray, foaming applicator, or pressure washer. c) Whenever possible, allow several minutes (5-10) of contact time to loosen oil. Do not allow product to dry on the surface or it will be difficult to remove. d) Wash and scrub as necessary. e) Rinse cleansed surfaces with clean water. Whenever possible, rinse should enter a pretreatment system (e.g., clarifier, oil/water separator, municipal sanitary sewer) before repurposing. 3. Conditions for Use: SIMPLE GREEN® can be used in freshwater, estuarine, and marine environments at all temperatures. Prior to application, booms, oil skimmers, or other appropriate containment and collection mechanism should be deployed and operational. Collected product and oil mixture should be disposed of according to local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) SIMPLE GREEN® Menidia beryllina 735.00 96-hr Mysidopsis bahia 541.00 48-hr No. 2 Fuel Oil Menidia beryllina 26.40 96-hr Mysidopsis bahia 3.37 48-hr Surface Washing Agents 401 SIMPLE GREEN® 2013 REFORMULATION ------- SIMPLE GREEN® & No. 2 Fuel Oil (1:10) Menidia beryllina 28.50 96-hr Mysidopsis bahia 5.05 48-hr Reference Toxicant (DSS) Menidia beryllina 1.69 96-hr Mysidopsis bahia 6.60 48-hr NOTE: This toxicity data was derived using the concentrated product. See Section VI of this bulletin for information regarding the manufacturer's recommendations for concentrations and application rates for field use. b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS SIMPLE GREEN® contains no microorganisms, enzymes, or biological material. IX. PHYSICAL PROPERTIES 1. Flash Point (ASTM 92): 98°C No Flash Point seen at or below 212°F (ASTM 93) 2. Pour Point: 0°C 3. Viscosity: <2.0 mm2/s at 40°C 4. Specific Gravity: 1.0283 g/ml at 60°F 5. pH: 9.0 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility: 100% soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.0031 Cadmium <0.0005 Chromium 0.013 Copper <0.0025 Lead <0.0005 Mercury 0.0016 Nickel 0.0054 Zinc 0.016 Cyanide <0.08 Chlorinated Hydrocarbons <5 Surface Washing Agents 402 SIMPLE GREEN® 2013 REFORMULATION ------- TECHNICAL PRODUCT BULLETIN #SW-65 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: JANUARY 23, 2014 "NONTOX™ SURFACE WASHING AGENT" I. NAME, BRAND, OR TRADEMARK NONTOX™ SURFACE WASHING AGENT Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Bio-Organic Catalyst, Inc. (wholly owned subsidiary of Neozyme International, Inc.) 711 West 17th Street, Suite E-6 Costa Mesa, CA 92627 Phone: (949) 515-1301 Phone: (800) 982-8676 Fax: (949)515-1314 E-mail: parker@bio-organic.com Website: www.bio-organic.com (Mr. Parker Dale, President) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Government Logistics Solutions Rolling Hills Construction and Demolition 3540 Chaneyville Road Recycling Center Owings, MD 20736 6990 Rolling Hills Road Phone: (410) 286-0098 Pensacola, FL 32505 Fax: (301) 812-2878 Phone: (850) 477-2687 (Mr. Charles M. Baker, Retired USAF (SMSgt (Mr. John Levitan - Mobile (850) 497-2724) sel), President) (Mr. Scott Miller - Mobile (850) 723-5715) (Kelly Davis - (240) 691-3946) (Mr. Charlie Davidson - Mobile (850) 776-2852) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: >93°C 2. Ventilation: None required. No respiratory protection required. 3. Skin and eye contact; protective clothing; treatment in case of contact: The use of protective eyewear and rubber gloves is recommended under good manufacturing practices. 4.a. Maximum storage temperature: 55°C 4.b. Minimum storage temperature: 2°C 4.c. Optimum storage temperature range: 25°C to 40°C 4.d. Temperatures of phase separations and chemical changes: No phase separations or chemical changes observed under optimum storage temperatures. Surface Washing Agents 403 NONTOX™ SURFACE WASHING AGENT ------- V. SHELF LIFE A minimum of two (2) years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: For general use apply the product by spray, mop or with standard steam and pressure wash cleaning equipment. It can also be applied using a foam generator or any convenient sprayer. Product can be used as is or by using heat and pressure or mechanical scrubbing. Rinse thoroughly with salt or fresh water for a residue-free surface. For direct applications foaming will be most effective as it will allow more contact time for the product to work. In a foam-cleaning application operation, the surface to be cleaned will be thoroughly covered with foam and allowed to stand for several minutes. The foam is rinsed away with clean water using a high pressure washer. The product can be applied with a variety of spraying or washing equipment, depending on the type and scale of the shoreline or beach to be cleaned. For large areas, such as beaches, the product can be sprayed from water trucks or other vehicles equipped with pumps, hoses and nozzles to aerially deliver the product. On smaller oily surfaces, the product can be applied with hand sprayers or portable pumps may be used to spray directly onto the contaminated areas. 2. Concentration/Application Rate: For spills on shorelines and beaches, the product can be used at a dilution of 1:17 parts product to water using salt or fresh water. After application, the product should be allowed to penetrate and dissolve the oily surface for up to 30 minutes. Longer is preferable to maximize contact time. For light cleaning use a ratio up to 1:50 parts product to water. For heavy cleaning use a ratio up to 1:17 parts product to water. Dose rates may vary depending on type and amount of petroleum spilled, and other site conditions such as water, temperatures and porosity of shoreline. Cold weather applications will require more contact time before initiating recovery. 3. Conditions for Use: The product can be used on sand beaches, gravel, cobble, and coarse sand and rocky shores. Water salinity should not negatively impact product use. Water temperatures below 2°C may impact application. Aged or highly viscous concentrations of hydrocarbons my require presoaking prior to removal. The treated product can be collected and removed by several means including, but not limited to, sorbent pads, oil skimmers, collection booms, or other appropriate containment and collection mechanism. All oily water mixtures should follow disposal procedures in accordance with current local, state and federal regulations. Surface Washing Agents 404 NONTOX™ SURFACE WASHING AGENT ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested NONTOX™ SURFACE WASHING AGENT No. 2 Fuel Oil NONTOX™ SURFACE WASHING AGENT & No. 2 Fuel Oil (1:10) Reference Toxicant (SLS) b. Effectiveness: NA Species LC50 (ppm) Menidia beryllina 203. .04 96-hr Mysidopsis bahia 316. .23 48-hr Menidia beryllina 2. .51 96-hr Mysidopsis bahia 2. .24 48-hr Menidia beryllina 3. .29 96-hr Mysidopsis bahia 2. .19 48-hr Menidia beryllina 12. .25 96-hr Mysidopsis bahia 12. .08 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 2.Flash Point (ASTM 92): >93°C 2. Pour Point: 2.22°C 3. Viscosity: 2.3373 cST @ 40°C 4. Specific Gravity: 1.005 at 68°F 5. pH: 3.46 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: None 8. Additives: CONFIDENTIAL 9. Solubility: 100% soluble X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.0100 Cadmium <0.0050 Chromium 0.1515 Copper 0.1530 Lead <0.0100 Mercury <0.5000 ug/L Nickel <0.0250 Zinc 4.781 Cyanide <0.0100 Chlorinated Hydrocarbons <2.50 Surface Washing Agents 405 NONTOX™ SURFACE WASHING AGENT ------- LAST COMMUNICATION WITH MANUFACTURER: LAST ATTEMPT: TECHNICAL PRODUCT BULLETIN #SW-66 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: MAY 7, 2015 "FORMULA 206-lx BIO-WASH™" (aka, CAST OFF™, FORMULA 206-lx) I. NAME, BRAND, OR TRADEMARK FORMULA 206-IX BIO-WASH™ (aka, CAST OFF™, FORMULA 206-lx) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Natural Soap Formulas, Inc. 3200 S Andrews Avenue, Suite 113 Fort Lauderdale, FL 33316 Phone: updated information required E-mail: updated information required (Ms. Kaylin D'Aire) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Natural Soap Formulas, Inc. 3200 S Andrews Avenue, Suite 113 Fort Lauderdale, FL 33316 Phone: updated information required E-mail: updated information required (Ms. Kaylin D'Aire) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable (DOT: Non-Hazardous) 2. Ventilation: Normal ventilation is adequate. No respiratory protection is required. If respiratory irritation or distress occurs, remove exposed person to fresh air. Seek medical attention if respiratory irritation or distress continues. 3. Skin and eye contact; protective clothing; treatment in case of contact: Protective eyewear is advisable for operator's comfort. If eye irritation occurs, flush eyes with water. After initial flushing, removal any contact lenses and continue flushing for 1 minute. Please seek medical attention, if eye irritation symptoms persist or if there are additional concerns. Wash hands after handling. If ingested, drink 2-4 glasses of water and allow the product to pass through the digestive system naturally. Ingesting large amounts may cause gastrointestinal distress due to emulsification of grease and oil in the digestive tract. Please seek medical attention, if symptoms persist of if there additional concerns. 3/16/2016 7/27/2022 Surface Washing Agents 406 FORMULA 206-IX BIO-WASH™ ------- 4.a. Maximum storage temperature: 120°F continuous, 130°F up to 5 days 4.b. Minimum storage temperature: 30°F 4.c. Optimum storage temperature range: 40°F to 110°F 4.d. Temperatures of phase separations and chemical changes: Stable V. SHELF LIFE 5 years in sealed poly drums or IBC totes (as delivered). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: FORMULA 206-lx BIO-WASH™ may be applied to hard surfaces including beaches, shorelines, and rocks; specifically to aid in the removal of oil and oil saturated soiling. Product may be applied by spray, high pressure wash, mop, scrub brush, cloth or sponge. Once applied to target surface, allow for a 5 to 30 minute dwell time, the product may be agitated using suitable physical methods (i.e., scrubbing to increase effectiveness). For large areas such as shorelines, product can be applied by vehicle or boat; spraying from fire eduction systems or boom system, hand-held or backpack sprayers, garden type sprayers, or from hoses attached to small pumps through power washers, fire pump or other portable pump with suction that is equipped with a chemical inductor or feed pump. After application, the removal of oil or oil saturated soiling can be done by rinsing with water where practicable followed by removal with physical methods, such as sorbent pads, mop or vacuum application to prevent contamination to open water. Ensure boom containment continues to be in place during oil/product removal procedures. 2. Concentration/Application Rate: FORMULA 206-lx BIO-WASH™ is typically diluted with using tap-water at ambient temperature; and can be diluted with sea water or any other suitable field expedient water source. The product is not affected by salinity or hard water dilution. Apply using a typical dilution ratio of 1:10 in the first instance. Product dilution varies with the severity of the contamination, contaminant viscosity, area of application and porosity, and nature of the surface to be decontaminated. A dilution ratio ranging from 1:5 to 1:200 is recommended for this product, there is no specific application rate; however, for large area application, 15 to 50 U.S. gallons per acre can be considered optimal. During application, the rate and concentration of the product can be adjusted to suit the cleaning effect desired. 3. Conditions for Use: FORMULA 206-lx BIO-WASH™ is most effective on hydrocarbon and bio-organic soiling on hard surfaces including beaches, shorelines, and rocks. A sorbent boom or other containment equipment should be positioned prior and remain in place during product use to collect runoff from application and removal operations. Collect and contain runoff from oil/product mixture and dispose of such material in accordance with local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Surface Washing Agents 407 FORMULA 206-IX BIO-WASH™ ------- Material Tested Species LC50 (ppm) FORMULA 206-lx BIO-WASH™ Menidia beryllina 157.00 96-hr Mysidopsis bahia 123.00 48-hr No. 2 Fuel Oil Menidia beryllina 3.60 96-hr Mysidopsis bahia 5.80 48-hr FORMULA 206-lx BIO-WASH™ & Menidia beryllina 3.90 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 4.10 48-hr Reference Toxicant (SDS) Menidia beryllina 10.00 96-hr Mysidopsis bahia 19.00 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 3. Flash Point (ASTM 93): 130°F 2. Pour Point (D2500): 30°F 3. Viscosity (ASTMD88): 26 SUS @ 100°F 4. Specific Gravity (ASTM D1217): 1.0137 g/ml at 60°F 5. pH (EPA 9040C): 10.6 6. Surface Active Agents: Natural fatty acid soaps 7. Solvents: Hydrofurfuryl Alcohol 8. Additives: NA 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic ND Cadmium ND Chromium 0.0173 Copper 0.115 Lead ND Mercury ND Nickel 0.160 Zinc 0.556 Cyanide ND Chlorinated Hydrocarbons ND Surface Washing Agents 408 FORMULA 206-IX BIO-WASH™ ------- TECHNICAL PRODUCT BULLETIN #SW-67 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 3, 2015 "RHAMNOWASH 10" I. NAME, BRAND, OR TRADEMARK RHAMNOWASH 10 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Rhamnolipid, Inc. 511 West Bay Street, Suite 350 Tampa, FL 33606 Phone: (917) 576-7381 Direct: (704) 564-6445 E-mail: greccosg@rhamnolipid.com Website: http://www.rhamnolipid.com (Mr. Samuel G. Grecco) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Rhamnolipid Companies, Inc. 511 West Bay Street, Suite 350 Tampa, FL 33606 Phone: (917) 576-7381 Direct: (704) 564-6445 E-mail: kdesanto@rhamnolipid.com Website: http://www.rhamnolipid.com (Mr. Keith DeSanto) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO, Non-flammable; DOT, Non-Hazardous 2. Ventilation: Inhalation causes irritation. Use in properly ventilated areas, with approved respiratory mask and goggles. Avoid creating mist where possible. If inhaled, allow plenty of fresh air and loosen clothing around neck. Contact physician immediately. 3. Skin and eye contact; protective clothing; treatment in case of contact: Exposure to skin can cause irritation if person has a history of dermal allergic reaction. Limit exposure and use rubber gloves. Wash with soap and water. If product comes in contact with the eyes, excess redness and swelling of the conjunctiva may occur. Causes moderate to severe irritation, which is experienced as discomfort or pain, excessive blinking and tear production, with marked excessive redness and swelling. Corneal injury may occur. Immediately flush with water for at least 15 minutes. DO NOT remove contact lenses, if worn. Obtain medical attention without delay, preferably from an ophthalmologist. To avoid eye contact, wear goggles or a face shield. Surface Washing Agents 409 RHAMNOWASH 10 ------- Ingestion of product can lead to nausea or diarrhea. If ingested, give two glasses of water to dilute product. DO NOT induce vomiting. Contact physician immediately. Treat as you would any chemical or biological material. Always wash hands thoroughly after use. Follow product sheets and SDS instructions. 4.a. Maximum storage temperature: 105°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 35°F to 75°F 4.d. Temperatures of phase separations and chemical changes: Phase separation may occur over time, but mild agitation will reconstitute mixture. V. SHELF LIFE The shelf life of unopened containers (i.e., drums, totes, etc.) of RHAMNOWASH 10 exceeds five (5) years. Containers should always be capped when not in use to prevent spillage and/or contamination. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: RHAMNOWASH 10 can remove oil (e.g., crude, different grades of fuel oil, gasoline, and other petrochemicals) from soil, shorelines, sandy beaches, mangroves, or sea grasses. The product may be applied by hand or using mechanical sprayers, pressure washers, or mechanical soil washing equipment. After a soak time of approximately 30 minutes to 3 to 4 hours (depending on the nature of the spill repeat as necessary), the residual mixture may be recovered using conventional methods. Actual cleaning time will likely depend on the environmental conditions, chemistry of the spilled oil, and the cleaning method employed. 2. Concentration/Application Rate: On heavy oils, use RHAMNOWASH 10 (neat) directly on the spill, or use a 1:100 dilution ratio (product: water) depending on the nature of the oil (e.g., crude vs refined) and environmental conditions (e.g., warm vs cold water). Lighter oils may need a 1:100 to 1:1000 dilution ratios depending on the oil's specific gravity and environmental conditions. RHAMNOWASH 10 maintains its surfactant properties at high levels of dilution, and works best when diluted with water (can use either saltwater or freshwater). 3. Conditions for Use: RHAMNOWASH 10 can be applied on oiled surfaces and shorelines in both freshwater and saltwater. Water temperatures less than 65°F may require higher dilution rates. Sorbent booms, oil skimmers, or other containment equipment should be positioned prior to and remain in place during product use to collect runoff from application and removal operations. Collect and contain runoff from oil/product mixture and dispose of such material in accordance with local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) RHAMNOWASH 10 Menidia beryllina 76.64 96-hr Mysidopsis bahia 164.61 48-hr Surface Washing Agents 410 RHAMNOWASH 10 ------- No. 2 Fuel Oil Menidia beryllina 10.85 96-hr Mysidopsis bahia 2.27 48-hr RHAMNOWASH 10 & Menidia beryllina 13.70 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.15 48-hr Reference Toxicant (SDS) Menidia beryllina 7.52 96-hr Mysidopsis bahia 5.47 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point (ASTM D-56): >100°C 2. Pour Point (ASTM D-97): 2.6°C 3. Viscosity (ASTM D-445): 2.02 est @ 40°C 4. Specific Gravity (ASTM D1298): 1.009 at 60°F 5. pH (ASTM D-1293): 6.5 6. Surface Active Agents: Anionic and nonionic, proprietary surfactants 7. Solvents: None 8. Additives: None 9. Solubility: Miscible X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.250 Cadmium <0.099 Chromium <0.250 Copper <0.740 Lead <0.200 Mercury <0.0033 Nickel <0.200 Zinc <5.000 Cyanide <2.500 Chlorinated Hydrocarbons <5.000 Surface Washing Agents 411 RHAMNOWASH 10 ------- TECHNICAL PRODUCT BULLETIN #SW-68 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: AUGUST 22, 2016 "ADP-7" I. NAME, BRAND, OR TRADEMARK ADP-7 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Petro-Green, Inc. Mailing Address 3952 Candlenut Lane Petro-Green, Inc. Dallas, TX 75244 P.O. Box 814665 Phone: updated information required Dallas, TX 75381 E-mail: adp7@petro-green. com (Mr. Michael Paddock) E-mail: michael.paddock@petro-green.com Website: www.petro-green.com (Mr. Michael Paddock) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Petro-Green, Inc. Mailing Address 3952 Candlenut Lane Petro-Green, Inc. Dallas, TX 75244 P.O. Box 814665 Phone: updated information required Dallas, TX 75381 E-mail: adp7@petro-green. com (Mr. Michael Paddock) E-mail: michael,paddock@petro-green.com Website: www.petro-green.com (Mr. Michael Paddock) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-Flammable (DOT: Non-Hazardous) 2. Ventilation: In most instances there will be no special requirements. However, if exposure limits are exceeded or irritation is experienced, NIOSH/MSHA approved respiratory protection should be worn. Positive pressure supplied air respirators may be required for high airborne contaminant concentrations. 3. Skin and eye contact; protective clothing; treatment in case of contact: First Aid: Skin/Body Contact - Wash off immediately with soap and water while removing all contaminated clothing and shoes. Wash all before reuse. Consult physician if irritation persists. Eyes - Immediately flush with plenty of water. After initial flushing, remove contact lenses if present and continue flushing for at least 15 minutes. If symptoms persist contact physician. Ingestion - Rinse mouth. Drink plenty of water. Do NOT induce vomiting. If symptoms persist contact physician. Surface Washing Agents 412 ADP-7 ------- Inhalation - Move to fresh air. If breathing is irregular or stopped administer artificial respiration. Call physician. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 26°F 4.c. Optimum storage temperature range: 40°F to 110°F 4.d. Temperatures of phase separations and chemical changes: Stable within storage temperature range. V. SHELF LIFE Unlimited in sealed poly drums (as delivered). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: For spills on soils, sandy or rocky areas: ADP-7 can be pre-mixed into water, or educed into a water flow, to be sprayed directly onto the oil spill. 2. Concentration/Application Rate: For spills on land: Typical dilution is one gallon of ADP-7 diluted with 42 gallons of water (approximately 2.4% concentration). Higher water temperatures (over 78°F) and/or good agitation during application will allow you to reduce the concentration strength. Aged or asphaltic spills may be more resistant to removal. Heating the solution to 150°F in a hot water washing rig, or a common oil field "hot oiler" truck will increase effectiveness. 3. Conditions for Use: ADP-7 is effective in salt water or fresh water, with no limitations as to usage within optimum temperature parameters (application may be made at or above 35°F, with optimum above 48°F). A sorbent boom or other containment equipment should be positioned prior to product application and should remain in place during product use to collect runoff from application and removal operations. The oil/product residue should be collected and removed from the site. Collection process should be determined by onsite coordinator based on practices of the area. Residue should be disposed of according to local, state and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested Species LC50 (ppm) ADP-7 Menidia beryllina 20.28 96-hr Mysidopsis bahia 22.36 48-hr No. 2 Fuel Oil Menidia beryllina 17.46 96-hr Mysidopsis bahia 5.30 48-hr ADP-7 & Menidia beryllina 14.10 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 3.24 48-hr Reference Toxicant (SDS) Menidia beryllina 3.42 96-hr Mysidopsis bahia 7.81 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS Surface Washing Agents 413 ADP-7 ------- NA IX. PHYSICAL PROPERTIES 1. Flash Point (ASTM D-56): >212°F 2. Pour Point (ASTM D-97): 21°F 3. Viscosity (ASTM D-445): 81.4 est @ 40°C 4. Specific Gravity (ASTM D-287): 1.0985 at 60°F 5. pH (ASTM D-1293): 9.9 6. Surface Active Agents: Anionic and nonionic 7. Solvents: Confidential 8. Additives: Confidential 9. Solubility: Miscible in oil, water, and solvents X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.485 Cadmium <0.243 Chromium <0.243 Copper <0.485 Lead <0.585 Mercury <3.26 |ig/L Nickel <0.485 Zinc <0.485 Cyanide <0.115 Chlorinated Hydrocarbons <2.00 Surface Washing Agents 414 ADP-7 ------- TECHNICAL PRODUCT BULLETIN #SW-69 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION ORIGINAL LISTING DATE: SEPTEMBER 7, 2016 "WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE" (aka, HEAVY DUTY DEGREASER CONCENTRATE) I. NAME, BRAND, OR TRADEMARK WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE (aka, HEAVY DUTY DEGREASER CONCENTRATE) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT KetecaUSA, Inc. 4280 W. Opportunity Way Phoenix, AZ 85086 Phone: (602) 278-7789 Fax: (602)535-1305 E-mail: sales@ketecausa.com E-mail: kparks@ketecausa.com Web site: www.ketecawaterworks.com (Ms. Kathy Parks) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS KetecaUSA, Inc. 4280 W. Opportunity Way Phoenix, AZ 85086 Phone: (602) 278-7789 Fax: (602)535-1305 E-mail: sales@ketecausa.com E-mail: kparks@ketecausa.com Web site: www.ketecawaterworks.com (Ms. Kathy Parks) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-Flammable (DOT: Non-Hazardous) 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with eyes, slight irritation may result. Wear splash goggles or full face-shield and have eye washing equipment available in areas where potential is high for eye contact. Skin contact will not cause irritation in the majority of users. If eye or skin irritation occurs, flush with plenty of fresh water. No special precautions or additional protective equipment are required during handling or use. Surface Washing Agents 415 WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE ------- Water Works™ Heavy Duty Degreaser Concentrate is provided with a Safety Data Sheet. 4.a. Maximum storage temperature: 100°F continuous, 110°F up to 5 days, keep away from direct sun light. 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: >32°F to <100°F 4.d. Temperatures of phase separations and chemical changes: Stable and phase separation will not occur at temperatures within the storage temperature range. V. SHELF LIFE 12 months from date of manufacturer in unopened original packaging (as delivered). Containers should always remain closed when not in use to prevent contamination and evaporation. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Product may be applied to rocks, shoreline, and beaches for removal of oil. Select proper dilution depending on product types and contaminated material surface prior to application. For treatment of large areas, properly diluted product may be applied by spraying with a pressure washer, portable fire pump or any other suitable pump with seawater or freshwater suction that is equipped with a chemical inductor or feed pump. For smaller areas, properly diluted product may be applied with scrubber, mop, cloth or damp sponge. Apply liberally, adjusting dilution on site as necessary. 2. Concentration/Application Rate: For heavily weathered oil on rocks, applying concentrated or diluted solution at 5 parts water to 1 part product is recommended. For heavily weathered oil on beaches/sand, a diluted solution of 2 parts water to 1 part product is ideal. For tar balls, no dilution is necessary and applying product at full strength is recommended. For removing oil from vegetation, a diluted solution of 10-20 parts water to 1 part product is preferred. Product may be diluted with either saltwater or freshwater. Warmer waters (greater than 78°F) and/or good agitation during application will require less product. 3. Conditions for Use: Can be used in freshwater, estuarine, and marine environments at all temperatures. Prior to application, booms, oil skimmers, or other appropriate containment and collection mechanism should be deployed and operational. Collected product and oil mixture should be disposed of according to local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE No. 2 Fuel Oil WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE & Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina LC50 (ppm) 68.70 96-hr 91.70 48-hr 11.53 96-hr 2.10 48-hr 14.60 96-hr Surface Washing Agents 416 WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE ------- 2.27 48-hr 7.68 96-hr 5.27 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA No. 2 Fuel Oil (1:10) Mysidopsis bahia Reference Toxicant (SDS) Menidia beryllina Mysidopsis bahia IX. PHYSICAL PROPERTIES 1. Flash Point (ASTM D-56): >212°F 2. Pour Point (ASTM D-97): 26°F 3. Viscosity (ASTM D-445): 2.66 est @ 40°C 4. Specific Gravity (ASTM D-1298): 1.0728 at 60°F 5. pH (ASTM D-1293): 9.4 6. Surface Active Agents: Proprietary surfactants 7. Solvents: None 8. Additives: None 9. Solubility: Soluble in water X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.001 Cadmium <0.001 Chromium <0.005 Copper <0.01 Lead 0.0163 Mercury <0.0002 Nickel 0.0167 Zinc 0.025 Cyanide 0.21 Chlorinated Hydrocarbons 6.22 Surface Washing Agents 417 WATER WORKS™ HEAVY DUTY DEGREASER CONCENTRATE ------- TECHNICAL PRODUCT BULLETIN #SW-70 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: MARCH 05, 2019 "X4JH2000" I. NAME, BRAND, OR TRADEMARK X4JH2000 Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT X4 Environmental Inc. 14702 Jersey Shore Drive Houston, TX 77047 Phone: (281) 846-6003 E-mail: benlux.tam@x4environmental.com (TszFung Benlux Tam) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS X4 Environmental Inc. 14702 Jersey Shore Drive Houston, TX 77047 Phone: (281) 846-6003 E-mail: benlux.tam@x4environmental.com (TszFung Benlux Tam) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable 2. Ventilation: Recommend using a respirator in confined areas. 3. Skin and eye contact; protective covering; treatment in case of contact: Wear rubber gloves and eye protection. In case of eye contact, wash eyes thoroughly for 15 minutes including upper and lower lids; and seek medical attention. In case of skin contact, irritation is possible; wash with soap and water for 15 minutes. If irritation persists, seek medical attention. 4.a. Maximum storage temperature: 95°F 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 75°F 4.d. Temperatures of phase separations and chemical changes: No phase changes have been observed. V. SHELF LIFE One year in a sealed container; and six months for an opened container. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: X4JH2000 is applied by spraying apparatus or mixing on or into media Surface Washing Agents 418 X4JH2000 ------- using excavator and 2-inch discharge hose, fire nozzle, or water pump; and water trucks. 2. Concentration/Application Rate: X4JH2000 is a water-based chemical. Use a ratio of 1 to 1.5 U.S. gallons of X4JH2000 to 10 parts water (i.e., tap, salt or fresh water) per cubic yard of contaminated media. 3. Conditions for Use: Ambient temperature should be above 50°F. Water salinity and age of hydrocarbon pollutants are not a condition of use. Prior to application, use oil spill absorbent, boom and/or pad to prevent X4JH2000 from run off into ditches, creeks, and waterways. Place collected booms, pads, and absorbents in black 55-gallon poly-bags, use duct tape to seal, and then place bags in hazardous waste container for disposal. Collected containment materials should be disposed of according to local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested Species LC50 (DDm) X4JH2000 Menidia beryllina 145.89 96-hr Mysidopsis bahia 40.26 48-hr No. 2 Fuel Oil Menidia beryllina 18.82 96-hr Mysidopsis bahia 1.49 48-hr X4JH2000 & Menidia beryllina 18.59 96-hr No. 2 Fuel Oil (1:10) Mysidopsis bahia 2.07 48-hr Reference Toxicant (SLS) Menidia beryllina 4.64 96-hr Mysidopsis bahia 8.42 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point (ASTM D-56): >220°F 2. Pour Point (ASTM D-57): +28°F 3. Viscosity (ASTM D-445): 4.99cSt at 40°C 4. Specific Gravity (ASTM D-1298): 1.06 at 60°F 5. pH (ASTM D-1293): 4.69 6. Surface Active Agents: HS Code 340211 anionic organic surface-active agents 7. Solvents: Not applicable 8. Additives: Not applicable 9. Solubility in Water: Not applicable Surface Washing Agents 419 X4JH2000 ------- X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS CYANIDE, AND CHLORINATED Compound Concentration (ppm) Arsenic <0.050 Cadmium <0.025 Chromium <0.050 Copper <0.100 Lead <0.050 Mercury <0.010 Nickel <0.050 Zinc 0.461 Cyanide <0.025 Chlorinated Hydrocarbons <1.000 Surface Washing Agents 420 X4JH2000 ------- TECHNICAL PRODUCT BULLETIN #SW-71 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: JUNE 30, 2020 "TASMANIA C-CLENZ" I. NAME, BRAND, OR TRADEMARK TASMANIA C-CLENZ Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE Head Office Physical Address Tasmania Limited 104 Forest Drive La Lucia, 4051, Durban, South Africa (Mr. John Webster, CEO) vtBER OF MANUFACTURER/CONTACT Headquarter's Office Postal Address Tasmania Limited P.O. 242 Umhlanga Rocks, 4320, Durban, South Africa (Mr. John Webster, CEO) Product Management Office: (+27) 562-9490 Mobile: (+27) 82-775-6555 U.S. Number: (904) 352-7195 E-mail: iohn.webster@tasmanialimited.com Website: www.tasmanialimited.com (Mr. John Webster, CEO) U.S. Postal Address Tasmania Limited 1958 East Peachtree Street Nashville, AR 71852 Phone: (936) 777-4270 E-mail: moxxyoil@gmail.com (Mr. Jeff Parker) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Skyfirm SA (Pty) Ltd Sam Jariri Nicol Grove Office Park 6314 Washington Blvd William Nicol Drive Arlington, VA 22205 Johannesburg, 2191, South Africa Office: (202) 664-9250 Mobile: (+27) 76-280-0624 E-mail: sam.iariri@tasmanialimited.com E-mail- martin@skyfirmsa.com (Mr. Sam Jariri) (Mr. Martin Schnuir) Tasmania Limited 6 Lauderdale, 50 Chartwell Drive Umhlanga Rocks, 4015, South Africa Mobile: (+27) 71-419-1421 E-mail: russ@tasmanialimited.com (Mr. Russell Parsons) Surface Washing Agents 421 TASMANIA C-CLENZ ------- IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: IMO - Non-flammable; DOT - Non-hazardous. 2. Ventilation: Handle in well ventilated space, local exhaust is recommended if threshold limit values are exceeded. If used in a confined area, wear a respirator. If used outdoors, no special equipment is needed. 3. Skin and eye contact; protective covering; treatment in case of contact: Use good normal hygiene and avoid contact with skin and eyes. Wear rubber or vinyl gloves when applying the product. Impermeable protective gloves are recommended for sensitive skin types. If contact is made, wash with soap and water. Contact may cause redness, edema and drying of skin. Seek medical attention if irritation develops. Wear protective eye goggles at all times. If in contact with eyes, flush with water for 15 minutes and seek medical attention. Rinse contaminated clothing, shoes, goggles and gloves in simple tap water to remove any chemical residue. In case of ingestion, give water and call a doctor or medical professional. Remove to fresh air. 4.a. Maximum storage temperature: 160°F 4.b. Minimum storage temperature: -25°F 4.c. Optimum storage temperature range: 60-90°F 4.d. Temperatures of phase separations and chemical changes: Temperature fluctuations will not cause separation or deterioration of the product. There are no chemical changes to the product at either the maximum or minimum temperature, the product is stable and will not undergo phase separation of ingredients or stratification of contents over time. V. SHELF LIFE The shelf life of an unopened TASMANIA C-CLENZ drum is 3 years. In case of opened drums, shelf life is 2 years. Keep product away from direct sunlight. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: TASMANIA C-CLENZ is for land use only. There are no application restrictions. The preferred application method is to apply the product over pollutant or stained area with a hand sprayer, pressure sprayer or a heated pressure spray unit. For the first application of TASMANIA C-CLENZ to shoreline contamination, use cold water/low pressure washing (<50 PSI) to remove any liquid oil that has adhered to the substrate, pooled on the surface or become trapped in vegetation. The average soak time of light oil contamination is 15-30 minutes. The average soak time of heavy oil contamination is 30-45 minutes, which allows the viscous oil deposits to soften. The actual soak time may vary with temperature, oil density and degree of weathering. The product starts to work on breaking the physical bond between the oil and the surface to be cleaned. In the case of heavy oil on the rocks or oil displaced into crevices, use warm water and moderate to high pressure washing with a temperature of 90°F and 100 PSI. When accessible or applicable, a work boat with mounted spray booms can be used to spray the product on the shoreline. Personnel can also apply the product with a hand sprayer or pressure sprayer. 2. Concentration/Application Rate: For heavily contaminated oil on rocks, use a full strength solution (non-diluted). For heavily weathered oil on beaches and rocks, a dilution of 5 parts water and 1 part product is ideal. For light contamination on the rocks, beaches and sand, a Surface Washing Agents 422 TASMANIA C-CLENZ ------- dilution of 10 parts water and one part product is used. Product can be diluted with either fresh or salt water. For removing oil from vegetation, a diluted solution of 15 parts water and one part product is preferred. Application rate is 1 gallon of product per square foot of surface area. 3. Conditions for Use: Used for cleaning petroleum fractions from shoreline, beaches and rocks. The water temperature can vary from 30-140°F. Best results are obtained by allowing either the non-diluted of diluted product to soak for 15-45 minutes depending on the severity of the pollutant on the area and whether the oil is weathered or is heavy oil. Adjust the pressure angle of the sprayer for optimal results. TASMANIA C-CLENZ can be used for contamination with all types of oil including heavily weathered and emulsified to light oil fractions, only the dilution amount will be adjusted. In the case of high temperatures above 75°F, use full strength TASMANIA C-CLENZ as the temperature and humidity will cause rapid evaporation of the spray. Greater results occur at ambient temperatures greater than 50°F. The salinity of the water has no effect on the performance of the product. Prior to application, use booms to prevent the product and oil mixture from entering open water. The product and oil mixture can be removed by either vacuum, skimmers or oil absorbents being applied in the boomed off area. The product and oil mixture, along with containment materials, should be disposed of according to local, state, and federal regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity Material Tested TASMANIA C-CLENZ No. 2 Fuel Oil TASMANIA C-CLENZ & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 141.16 96-hr 34.27 6.17 2.11 5.24 1.93 3.47 8.75 48-hr 96-hr 48-hr 96-hr 48-hr 96-hr 48-hr b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point (ASTM D-56): >100°C 2. Pour Point (ASTM D-97): +26°C 3. Viscosity (ASTM D-445): 2.299cSt at 60°F 4. Specific Gravity (ASTM D-287): 0.9678 at 60°F 5. pH: 7.0 6. Surface Active Agents: Confidential Surface Washing Agents 423 TASMANIA C-CLENZ ------- 7. Solvents: Confidential 8. Additives: Confidential 9. Solubility in Water: 100% X. ANALYSIS FOR HEAVY METALS, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons CYANIDE, AND CHLORINATED Concentration (ppm) 0.275 0.122 0.0406 0.272 0.154 0.0132 0.0154 0.195 0.00198 0.00050 Surface Washing Agents 424 TASMANIA C-CLENZ ------- TECHNICAL PRODUCT BULLETIN #SW-72 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: MAY 17, 2021 "GOLD CREW® TC" I. NAME, BRAND, OR TRADEMARK GOLD CREW® TC (aka, TRAFFIC COLLISION, SPILL CLEANUP AGENT) Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Gold Crew Products & Services, LLC P.O. Box 2039 Orange, CA 92869 Mobile: (714)318-5997 E-mail: ifigueira@goldcrew.net E-mail: ifigueira@ecschem.com (Mr. Jim Figueira) ECS 5713 Wollochet Drive NW, Suite B Gig Harbor, WA 98332 Phone: (253) 263-8040 E-mail: egrubbs@ecschem.com Website: www.ecschem.com (Mr. Ed Grubbs) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS ECS 5713 Wollochet Drive NW, Suite B Gig Harbor, WA 98332 Phone: (253) 263-8040 E-mail: egrubbs@ecschem.com Website: www.ecschem.com (Mr. Ed Grubbs) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Normal. 3. Skin and eye contact; protective clothing; treatment in case of contact: Good hygiene practices should always be followed. Wear impervious gloves for solutions or where contact is repeated. Avoid contact with eyes, skin, and clothing. Handle in accordance with good industrial hygiene and safety practices. For eye contact, flush with water and get medical attention if required. For skin contact, remove contaminated clothing and wash exposed area, and wash clothing before next use. If irritation develops get medical attention. If ingested, get medical attention. 4.a. Maximum storage temperature: When above 120°F, keep container closed and stored in a cool dark place. Evaporation may change product's characteristics. 4.b. Minimum storage temperature: Product will freeze below 25°F. No phase separation will occur. If frozen, thaw, and stir well. 4.c. Optimum storage temperature range: 25°F to 120°F. Use normal storage conditions, but store away from incompatible materials. Surface Washing Agents 425 GOLD CREW® TC ------- 4.d. Temperatures of phase separations and chemical changes: No separation at any temperature between 32-120°F. No tendency to "layer out" or separate, standing for 30 days. No separation of layering after freezing. V. SHELF LIFE 2 years (unopened); and 1 year (opened). VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Gold Crew® TC's mechanism of action desorbs or strips the hydrocarbon off the surface of the solid through surface tension reduction enhanced with physical agitation. The action is not a chemical reaction. 2. Concentration/Application Rate: For small hard surface area, active wash: Apply undiluted through hand pump sprayer. Apply to cover immediate work area. Use scrub brush to agitate. Use appropriate sorbent material to pick up and contain. For releasing from hard surface using presoak and/or power wash action: Boom off immediate work area. Use undiluted as presoak. Apply to cover the focused work area. Work on a test area first to determine site specific application. For crude oil, allow up to a 20-minute presoak. For medium distillates, allow 10 (±) minutes. For light distillates, allow 5 minutes. Times may vary depending on weather conditions/oil viscosity and site-specific conditions. After determining and applying the solution for presoak, wash down the area in the following manner: Gold Crew® TC should be used through a power washer or through a steam powered unit at 1 to 5 percent eduction rate to decrease the water's surface tension and enhance power washing effectiveness. Wash to boomed containment area and remove by absorbent or skimmer. Dispose of waste material according to federal, state, and local regulations. For power wash with no presoak, used undiluted through power washer for crude and heavy oils. For lighter distillate's dilute 50:50 with water. Follow containment and recovery methods. 3. Conditions for Use: Equally effective with salt or fresh water. Product will freeze in very low temperature but when thawed, will not affect performance. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested GOLD CREW® TC No. 2 Fuel Oil GOLD CREW® TC & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) b. Effectiveness: NA Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 630.00 96-hr 503.00 48-hr 8.77 96-hr 3.00 48-hr 5.65 96-hr 4.25 48-hr 1.90 96-hr 9.03 48-hr Surface Washing Agents 426 GOLD CREW® TC ------- VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >200 2. Pour Point: 32°F 3. Viscosity: 1.52 est @ 71°F (22°C); 1.213 est @ 104°F (40°C) 4. Specific Gravity: 1.002 5. pH: 8.78 (±0.01) 6. Surface Active Agents: CONFIDENTIAL. 7. Solvents: None. 8. Additives: CONFIDENTIAL. 9. Solubility in Water: Complete. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic 0.0343 Cadmium <0.0020 Chromium <0.0050 Copper 0.0166 Lead <0.0060 Mercury <0.0008 Nickel <0.0050 Zinc <0.0200 Cyanide <0.0050 Chlorinated Hydrocarbons ND Surface Washing Agents 427 GOLD CREW® TC ------- TECHNICAL PRODUCT BULLETIN #SW-73 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: SEPTEMBER 29, 2021 "DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE" I. NAME, BRAND, OR TRADEMARK DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Greenworld Innovations Corp. 3813 Highgate Drive Valrico, FL 33594 Phone: (407) 574-3898 Fax: (813)413-6073 E-mail: info@gwi.world Website: www.deoilit.com (Mr. Ron McCarthy, CEO, or Mr. Danny Schillaci, COO) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Greenworld Innovations Corp. 3813 Highgate Drive Valrico, FL 33594 Phone: (407) 574-3898 Fax: (813)413-6073 E-mail: info@gwi.world Website: www.deoilit.com (Mr. Ron McCarthy, CEO, or Mr. Danny Schillaci, COO) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: No mechanical ventilation required; fresh air supply recommended for inside confined spaces. 3. Skin and eye contact; protective clothing; treatment in case of contact: May cause eye irritation, manufacturer recommends use of goggles during application. In case of eye contact, flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes. For skin contact, wash exposed skin with soap and water. If redness, itching or a burning sensation develops get medical attention. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days. 4.b. Minimum storage temperature: 35°F. 4.c. Optimum storage temperature range: 40°F to 120°F. 4.d. Temperatures of phase separations and chemical changes: Stable; however, avoid freezing Surface Washing Agents 428 DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE ------- application solution (concentrated product diluted with water) to avoid possible separation. V. SHELF LIFE The shelf life of unopened containers is unlimited. Containers should remain capped when not in use to prevent contamination or evaporation. Activated concentrate (i.e., product diluted with water) has unlimited shelf life if kept capped. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Product is to be used in diluted form and works just as well with fresh or salt water. This product works well with all types of oils contaminating shorelines, beaches, and rocks. Dilute to 30:1 (this is the application solution comprised of 30 parts water and one part product), spray on surface areas, and allow to soak time for 15 minutes before rinsing with water. For stubborn oil cleanup, after soaking scrub with brush before rinsing. Spraying means using mechanical methods such as a pump that can deliver 30 psi or greater. Rinsing is best performed with a pressure washer if available. Prior to application, use booms to prevent the product and oil mixture from entering open water. Water run-off can be collected by a vacuum apparatus as surface tension of the treated oil is reduced making pick up efforts easier (should not stick to vacuuming). The product and oil mixture, along with containment materials, should be disposed of according to local, state, and federal regulations. 2. Concentration/Application Rate: The volume of an application solution for shoreline cleanup means adding water (30 parts) to product (one part) and is dependent on size of cleanup area. In general the calculation of application solution (water plus product) volume in gallons is (Length x Width)*(0.08) - scale is in feet. As an example, a boundary of contaminated shoreline measuring 50 feet x 12 feet, would be 600 square feet. Then 600 square feet * 0.08 = 48 gallons, at 30:1 dilution ratio this would be 1.5 gallons of product and 46.5 gallons of water. Water does not need to be filtered and can be salt or fresh. 3. Conditions for Use: Outside air temperature of 50°F to 125°F is optimal; otherwise, there is no specific restrictions outside this range other than avoid freezing of application solution. Water temperature for activating the application solution produces optimal performance between 95°F to 125°F; otherwise, there is no specific restrictions outside this range other than avoid freezing application solution. Water source for application solution can be fresh, or a non-potable source such as natural sources (i.e., lakes, ocean). Ambient water temperature at source of oil spill should be above 35°F. Do no freeze product, possible separation could occur. Manufacturer resting time of dilution application solution includes: • When creating a diluted application solution according to a selected dilution ratio, the combined solution of water and product needs to rest. • Resting time of 30 minutes to one hour stabilizing at ambient temperature to which you are to apply the application solution is optimal. Surface Washing Agents 429 DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE No. 2 Fuel Oil PRODUCT & No. 2 Fuel Oil (1:10) Reference Toxicant (DSS) b. Effectiveness: NA Species Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia LC50 (ppm) 144.59 96-hr 76.64 48-hr 10.55 96-hr 3.90 48-hr 4.65 4.13 3.98 8.36 96-hr 48-hr 96-hr 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >212°F 2. Pour Point: 26°F 3. Viscosity: 1.505 cSt @ 40°C 4. Specific Gravity: 1.1959 @ 60°F 5. pH: 12.9 6. Surface Active Agents: Anionic and nonionic surfactants, proprietary 7. Solvents: CONFIDENTIAL. 8. Additives: CONFIDENTIAL. 9. Solubility in Water: High solubility in water. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.050 Cadmium <0.025 Chromium <0.015 Copper <0.050 Lead <0.050 Mercury <1.00 ug/L Nickel <0.050 Zinc 0.249 Cyanide 0.0774 Chlorinated Hydrocarbons <0.005 Surface Washing Agents 430 DE-OIL-IT INDUSTRIAL STRENGTH CONCENTRATE ------- TECHNICAL PRODUCT BULLETIN #SW-74 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: NOVEMBER 17, 2021 "ECOGREEN" I. NAME, BRAND, OR TRADEMARK ECOGREEN Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Rose Rock Products, LLC P.O. Box 721926 Oklahoma City, OK 73172 Phone: (405) 883-1095 E-mail: Ken.Murphy@RoseRockEnv.com Website: www.RoseRockEnv.com (Mr. Ken Murphy, CEO) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Rose Rock Products, LLC EcoTec, LLC P.O. Box 721926 3 Nancy Court, Suite 4 Oklahoma City, OK 73172 Wappingers Falls, NY 12590 Phone: (405) 883-1095 Phone: (845) 897-0003 E-mail: Ken.Murphy@RoseRockEnv.com E-mail: WJordan@EcoTecLLC.com Website: www.RoseRockEnv.com Website: www.EcoTecLLC.com (Mr. Ken Murphy, CEO) (Mr. Wyatt Jordan) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Always keep exposure below permissible exposure limits. In general, dilution ventilation is a satisfactory health hazard control for this substance. However, if conditions of use create discomfort to the worker, a local exhaust system should be considered. 3. Skin and eye contact; protective clothing; treatment in case of contact: As prescribed in the OSHA Standard for Personal Protective Equipment (29 CFR 1910.132), employers must perform a Hazard Assessment for all workplaces to determine the need for, and selection of, proper protective equipment for each task performed. For skin and eye contact, use good normal hygiene and avoid contact with skin and eyes. For prolonged or repeated handling, use impervious gloves. Gloves should be tested to determine suitability for prolonged contact. Use of impervious apron and boots are recommended. Wear face shield, safety glasses, or chemical goggles are recommended for field application and product handling. If contact with eyes, flush with water for 15 minutes and see medical attention if irritation develops. For contact with skin, wash area with soap and water. May cause redness and drying of skin. Seek medical attention if Surface Washing Agents 431 ECOGREEN ------- irritation develops. In case of ingestion, seek medical attention. Not considered an inhalation risk. 4.a. Maximum storage temperature: 120°F. 4.b. Minimum storage temperature: Freeze temperature is 32°F. No deterioration in performance is expected as a result of freezing. Thaw product and mix thoroughly prior to use. 4.c. Optimum storage temperature range: 35°F to 120°F. 4.d. Temperatures of phase separations and chemical changes: Temperature fluctuations will not cause separation or deterioration of product. Product blend is stable and will not undergo phase separation of ingredients or stratification of contents over time. V. SHELF LIFE Unlimited shelf life (unopened), product should be used within 12 months of opening. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: Dilute product with water prior to use. Apply diluted product via manual pressure applicator (i.e., hand pump), or other delivery equipment, to impacted surfaces. Allow product to soak prior to rinse/recovery if heavily saturated with oil. On hard surfaces, product may be applied and agitated with a brush or other physical means prior to recovery of effluent. Product may also by pre-mixed and used in a batch tank or through an eduction/metering system for flushing and recovery operations. Any common pressure washer, either hot or cold, will be effective for proper application at recommended dilutions of ECOGREEN. Proper containment contingencies should be deployed prior to application of ECOGREEN solution to stranded oils on impacted substrates to ensure adequate recovery of treated oils. 2. Concentration/Application Rate: ECOGREEN is a concentrated product and must be diluted prior to use. Concentrations vary based upon type of oil and degree of surface saturation. For Light Ends (i.e., gas condensate/gasoline) a 1% to 2% solution may be used to flush area to containment. Note: A higher concentration solution of 5% to 6% should be used if flammable vapor presents an explosion hazard. For Lighter Oils (i.e., Diesel Fuel, #2 Fuel Oil) a 3% solution may be used to flush impacted areas to containment. For Heavy Ends (i.e., Crude Oil, #6 Fuel Oil) a 6% solution of ECOGREEN should be applied and allowed to soak into containment/substrate for up to an hour to allow for release of oil. The surface should then be flushed to containment with a 1% to 3% solution of ECOGREEN. Product may be used as noted above through any pressure or steam equipment. The use of a "hot" unit is recommended when oils are at low temperature or have been weathered. 3. Conditions for Use: ECOGREEN may be diluted with hard, soft, brackish, salt, or most waters of sufficient quality for operations. Upon proper application as noted above, all treated fluids should be flushed and/or directed to proper containment and recovery. Affected shorelines and other surfaces should be isolated with containment booms and/or sorbent materials prior to treatment to avoid release of treated fluids to open waters. Diversion of swales and temporary catchment sumps may be used for vacuum recovery of treated effluents. All recovered fluids should be disposed of in accordance with all federal, state, and local regulations. Surface Washing Agents 432 ECOGREEN ------- VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested ECOGREEN (neat) No. 2 Fuel Oil ECOGREEN & No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) b. Effectiveness: NA Species LC50 (ppm) Menidia beryllina 111.00 96-hr Mysidopsis bahia 104.00 48-hr Menidia beryllina 11.30 96-hr Mysidopsis bahia 1.74 48-hr Menidia beryllina 5.73 96-hr Mysidopsis bahia 1.84 48-hr Menidia beryllina 1.76 96-hr Mysidopsis bahia 4.24 48-hr VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: >230°F 2. Pour Point: 32.0°F 3. Viscosity: 4.403 cSt @ 104°F 4. Specific Gravity: 1.015 @ 60°F 5. pH: 8.3 6. Surface Active Agents: CONFIDENTIAL. 7. Solvents: CONFIDENTIAL. 8. Additives: CONFIDENTIAL. 9. Solubility in Water: Complete. X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS Compound Concentration (ppm) Arsenic <0.500 Cadmium <0.100 Chromium <0.250 Copper <0.500 Lead <0.300 Mercury <0.151 Nickel <0.250 Zinc <1.250 Cyanide <1.000 Chlorinated Hydrocarbons All < Method Quantification Limit Surface Washing Agents 433 ECOGREEN ------- NEW PRODUCT LISTING TECHNICAL PRODUCT BULLETIN #SW-75 USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION LISTING DATE: FEBRUARY 16, 2023 "ABLUOL OSASA H/C" I. NAME, BRAND, OR TRADEMARK ABLUOL OSASA H/C Type of Product: Surface Washing Agent II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT Taiwan Surfactant Corporation 8F1., No. 11, Sec. 1 Chung Shan North Road Taipei, 104, Taiwan Phone: 886-2-25410022 E-mail: twsa@twsa.com.tw Website: https://www.taiwan-surfactant.com/ (Mr. Lun Hsieh) III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS Taiwan Surfactant Corporation 8F1., No. 11, Sec. 1 Chung Shan North Road Taipei, 104, Taiwan Phone: 886-2-25410022 E-mail: twsa@twsa.com.tw Website: https://www.taiwan-surfactant.com/ (Mr. Lun Hsieh) IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION 1. Flammability: Non-flammable. 2. Ventilation: Normal ventilation, use of a respirator in confined areas is recommended. 3. Skin and eye contact; protective clothing; treatment in case of contact: As in handling any industrial chemical, the standard precautions of wearing chemical-resistant gloves and eye protection are recommended. Additional precautions include using non-sparking tools and avoiding exposure to aerosol vapor. 4.a. Maximum storage temperature: 212°F. 4.b. Minimum storage temperature: 32°F 4.c. Optimum storage temperature range: 68°F. Surface Washing Agents 434 ABLUOL OSASA H/C ------- 4.d. Temperatures of phase separations and chemical changes: May begin freezing below 25°F as product begins to get turbid. Stir until product becomes homogenous. No chemical changes. V. SHELF LIFE Two years (unopened). After confirming there is no contamination in opened barrels, opened barrels will have a shelf life of two years. VI. RECOMMENDED APPLICATION PROCEDURE 1. Application Method: ABLUOL OSASA H/C is water-based formulation. The product is used to remove oil from hard surfaces such as shorelines, rock, and sand. Prior to application of ABLUOL OSASA H/C, collection booms, oil skimmers, sorbent pads, or other appropriate containment and collection mechanism must be deployed and operational. Apply diluted product via manual pressure washer, spraying tools, or hand pumps. 2. Concentration/Application Rate: ABLUOL OSASA H/C is a highly concentrated product and must be diluted with water (salt or fresh) before use. Dilution ratios vary depending on the specific conditions of the contaminated site. The dilution ratio is approximately 1:80 to 1:100 (product: water). The application ratio of this diluted product to oil is approximately 1:10. For shorelines and rock, ABLUOL OSASA H/C is to be used in approximately a 1:80 to 1:100 dilution ratio (product:water). ABLUOL OSASA H/C is sprayed directly on the oiled rocky shorelines or rock. A dilution of ABLUOL OSASA H/C with warm waters (up to 176°F or 80°C) during application will enhance its washing effect on shorelines and rocks. After applying the diluted ABLUOL OSASA H/C by hand or spraying tools, soaking for approximately 10 minutes, the washing work can be started. Application of pressure washer will accelerate the washing process. For use on sand, ABLUOL OSASA H/C is to be used in approximately a 1:80 to 1:100 dilution ratio (product:water) under stirring. Oil will separate from sand and float on the surface of spray water for timely collection or adsorption. 3. Conditions for Use: Do not mix the product with any other cleaner or allow other cleaners to contact surfaces while using ABLUOL OSASA H/C. ABLUOL OSASA H/C does not contain petroleum distillates. The product works well with all types of oils and with salt or fresh water. Use booms or other containments prior application of ABLUOL OSASA H/C to prevent the product/oil mixture from reaching open water. Collect, remove, and dispose of product/oil mixture from site according to federal, state, and local regulations. VII. TOXICITY AND EFFECTIVENESS a. Toxicity: Material Tested ABLUOL OSASA H/C Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Menidia beryllina Mysidopsis bahia Species LC50 (ppm) 19.80 96-hr 28.10 48-hr 6.22 96-hr 1.41 48-hr 3.33 96-hr 1.32 48-hr 1.69 96-hr 4.64 48-hr No. 2 Fuel Oil ABLUOL OSASA H/C No. 2 Fuel Oil (1:10) Reference Toxicant (SDS) Surface Washing Agents 435 ABLUOL OSASA H/C ------- b. Effectiveness: NA VIII. MICROBIOLOGICAL ANALYSIS NA IX. PHYSICAL PROPERTIES 1. Flash Point: No flash 2. Pour Point: -21°C 3. Viscosity: 161 cSt @ 40°C 4. Specific Gravity: 1.102 @ 60°F 5. pH: 4.93 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: Water 8. Additives: CONFIDENTIAL 9. Solubility in Water: Soluble in fresh and salt water. AND CHLORINATED Concentration (ppm) <0.50 <0.10 <0.25 <0.50 <0.30 <0.0136 <0.25 <1.25 <1.00 Non Detect X. ANALYSIS FOR HEAVY METALS, CYANIDE, HYDROCARBONS Compound Arsenic Cadmium Chromium Copper Lead Mercury Nickel Zinc Cyanide Chlorinated Hydrocarbons Surface Washing Agents 436 ABLUOL OSASA H/C ------- |